RF PLL Frequency Synthesizers
Data Sheet
ADF4110/ADF4111/ADF4112/ADF4113
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2012 Analog Devices, Inc. All rights reserved.
FEATURES
ADF4110: 550 MHz; ADF4111: 1.2 GHz; ADF4112: 3.0 GHz;
ADF4113: 4.0 GHz
2.7 V to 5.5 V power supply
Separate charge pump supply (VP) allows extended tuning
voltage in 3 V systems
Programmable dual-modulus prescaler 8/9, 16/17, 32/33,
64/65
Programmable charge pump currents
Programmable antibacklash pulse width
3-wire serial interface
Analog and digital lock detect
Hardware and software power-down mode
APPLICATIONS
Base stations for wireless radio (GSM, PCS, DCS, CDMA,
WCDMA)
Wireless handsets (GSM, PCS, DCS, CDMA, WCDMA)
Wireless LANS
Communications test equipment
CATV equipment
GENERAL DESCRIPTION
The ADF4110 family of frequency synthesizers can be used to
implement local oscillators in the upconversion and downcon-
version sections of wireless receivers and transmitters. They
consist of a low noise digital PFD (phase frequency detector), a
precision charge pump, a programmable reference divider,
programmable A and B counters, and a dual-modulus prescaler
(P/P + 1). The A (6-bit) and B (13-bit) counters, in conjunction
with the dual-modulus prescaler (P/P + 1), implement an N
divider (N = BP + A). In addition, the 14-bit reference counter
(R counter) allows selectable REFIN frequencies at the PFD
input. A complete phase-locked loop (PLL) can be implemented
if the synthesizer is used with an external loop filter and voltage
controlled oscillator (VCO).
Control of all the on-chip registers is via a simple 3-wire
interface. The devices operate with a power supply ranging
from 2.7 V to 5.5 V and can be powered down when not in use.
FUNCTIONAL BLOCK DIAGRAM
N = BP + A
FUNCTION
LATCH
PRESCALER
P/P +1
13-BIT
B COUNTER
6-BIT
A COUNTER
14-BIT
R COUNTER
24-BIT
INPUT REGISTER
R COUNTER
LATCH
A, B COUNTER
LATCH
PHASE
FREQUENCY
DETECTOR
AV
DD
SD
OUT
19
13
14
22
SD
OUT
FROM
FUNCTION
LATCH
DGNDAGNDCE
RF
IN
A
RF
IN
B
LE
DATA
CLK
REF
IN
CPGND
V
P
DV
DD
AV
DD
LOCK
DETECT
ADF4110/ADF4111
ADF4112/ADF4113
6
LOAD
LOAD
REFERENCE
CHARGE
PUMP
M3 M2 M1
HIGH Z
MUX MUXOUT
CP
R
SET
CURRENT
SETTING 2
CPI3 CPI2 CPI1 CPI6 CPI5 CPI4
CURRENT
SETTING 1
03496-0-001
Figure 1. Functional Block Diagram
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 2 of 28
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Timing Characteristics ..................................................................... 5
Absolute Maximum Ratings ............................................................ 6
Transistor Count ........................................................................... 6
ESD Caution .................................................................................. 6
Pin Configurations and Function Descriptions ........................... 7
Typical Performance Characteristics ............................................. 8
Circuit Description ......................................................................... 12
Reference Input Section ............................................................. 12
RF Input Stage ............................................................................. 12
Prescaler (P/P + 1) ...................................................................... 12
A and B Counters ....................................................................... 12
R Counter .................................................................................... 12
Phase Frequency Detector (PFD) and Charge Pump ............ 13
Muxout and Lock Detect ........................................................... 13
Input Shift Register .................................................................... 13
Function Latch ............................................................................ 19
Initialization Latch ..................................................................... 20
Device Programming after Initial Power-Up ......................... 20
Resynchronizing the Prescaler Output .................................... 21
Applications ..................................................................................... 22
Local Oscillator for GSM Base Station Transmitter .............. 22
Using a D/A Converter to Drive the RSET Pin ......................... 23
Shutdown Circuit ....................................................................... 23
Wideband PLL ............................................................................ 23
Direct Conversion Modulator .................................................. 25
Interfacing ................................................................................... 26
PCB Design Guidelines for Chip Scale Package .................... 26
Outline Dimensions ....................................................................... 27
Ordering Guide ............................................................................... 28
REVISION HISTORY
8/12Rev. D to Rev. E
Changed CP-20-1 to CP-20-6 ........................................... Universal
Updated Outline Dimensions ........................................................ 28
Changes to Ordering Guide ........................................................... 28
5/12Rev. C to Rev. D
Changes to Figure 2 ........................................................................... 5
Changes to Figure 4 and Table 4 ...................................................... 7
Updated Outline Dimensions ........................................................ 28
Changes to Ordering Guide ........................................................... 28
3/04—Data sheet changed from Rev. B to Rev. C.
Updated Format .............................................................. Universal
Changes to Specifications ............................................................ 2
Changes to Figure 32 .................................................................. 22
Changes to the Ordering Guide ................................................ 28
3/03Data sheet changed from Rev. A to Rev. B.
Edits to Specifications ................................................................... 2
Updated OUTLINE DIMENSIONS ........................................ 24
1/01Data sheet changed from Rev. 0 to Rev. A.
Changes to DC Specifications in B Version, B Chips,
Unit, and Test Conditions/Comments Columns ................. 2
Changes to Absolute Maximum Rating ..................................... 4
Changes to FRINA Function Test ................................................. 5
Changes to Figure 8 ....................................................................... 7
New Graph AddedTPC 22 ....................................................... 9
Change to PD Polarity Box in Table V .................................... 15
Change to PD Polarity Box in Table VI ................................... 16
Change to PD Polarity Paragraph ............................................ 17
Addition of New Material
(PCB Design Guidelines for ChipScale package) ........... 23
Replacement of CP-20 Outline with CP-20 [2] Outline ....... 24
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 3 of 28
SPECIFICATIONS
AVDD = DVDD = 3 V ± 10%, 5 V ± 10%; AVDD ≤VP ≤ 6.0 V; AGND = DGND = CPGND = 0 V; RSET = 4.7 k; dBm referred to 50 Ω;
TA = TMIN to TMAX, unless otherwise noted. Operating temperature range is as follows: B Version: 40°C to +85°C.
Table 1.
Parameter B Version B Chips
1
Unit Test Conditions/Comments
RF CHARACTERISTICS (3 V) See Figure 29 for input circuit.
RF Input Sensitivity 15/0 15/0 dBm min/max
RF Input Frequency
ADF4110 80/550 80/550 MHz min/max For lower frequencies, ensure slew rate
(SR) > 30 V/µs.
ADF4110 50/550 50/550 MHz min/max Input level = 10 dBm.
ADF4111 0.08/1.2 0.08/1.2 GHz min/max For lower frequencies, ensure SR > 30 V/µs.
ADF4112 0.2/3.0 0.2/3.0 GHz min/max For lower frequencies, ensure SR > 75 V/µs.
ADF4112 0.1/3.0 0.1/3.0 GHz min/max Input level = 10 dBm.
ADF4113
0.2/3.7
0.2/3.7
Input level = 10 dBm. For lower frequencies,
ensure SR > 130 V/µs.
Maximum Allowable Prescaler Output
Frequency2 165 165 MHz max
RF CHARACTERISTICS (5 V)
RF Input Sensitivity 10/0 10/0 dBm min/max
RF Input Frequency
ADF4110 80/550 80/550 MHz min/max For lower frequencies, ensure SR > 50 V/µs.
ADF4111 0.08/1.4 0.08/1.4 GHz min/max For lower frequencies, ensure SR > 50 Vs.
ADF4112
0.1/3.0
0.1/3.0
For lower frequencies, ensure SR > 75 V/µs.
ADF4113 0.2/3.7 0.2/3.7 GHz min/max For lower frequencies, ensure SR > 130 V/µs.
ADF4113 0.2/4.0 0.2/4.0 GHz min/max Input level = 5 dBm.
Maximum Allowable Prescaler Output
Frequency2 200 200 MHz max
REFIN CHARACTERISTICS
REFIN Input Frequency 5/104 5/104 MHz min/max For f < 5 MHz, ensure SR > 100 V/µs.
Reference Input Sensitivity 0.4/AV
DD
0.4/AV
DD
V p-p min/max AV
DD
= 3.3 V, biased at AV
DD
/2. See Note 3.
3.0/AVDD 3.0/AVDD V p-p min/max AV
DD
= 5 V, biased at AV
DD
/2. See Note 3.
REFIN Input Capacitance 10 10 pF max
REFIN Input Current ±100 ±100 µA max
PHASE DETECTOR FREQUENCY
4
55 55 MHz max
CHARGE PUMP
I
CP
Sink/Source Programmable (see Table 9).
High Value 5 5 mA typ With RSET = 4.7 kΩ.
Low Value 625 625 µA typ
Absolute Accuracy 2.5 2.5 % typ With R
SET
= 4.7 kΩ.
RSET Range 2.7/10 2.7/10 kΩ typ See Table 9.
I
CP
3-State Leakage Current 1 1 nA typ
Sink and Source Current Matching 2 2 % typ 0.5 V ≤ VCP ≤ VP0.5 V.
I
CP
vs. V
CP
1.5 1.5 % typ 0.5 V ≤ V
CP
≤ V
P
0.5 V.
ICP vs. Temperature
2
2
VCP = VP/2.
LOGIC INPUTS
VINH, Input High Voltage 0.8 × DVDD 0.8 × DVDD V min
V
INL
, Input Low Voltage 0.2 × DV
DD
0.2 × DV
DD
V max
I
INH
/I
INL
, Input Current ±1 ±1 µA max
CIN, Input Capacitance 10 10 pF max
LOGIC OUTPUTS
V
OH
, Output High Voltage DV
DD
0.4 DV
DD
0.4 V min I
OH
= 500 µA.
V
OL
, Output Low Voltage 0.4 0.4 V max I
OL
= 500 µA.
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 4 of 28
Parameter B Version B Chips
1
Unit Test Conditions/Comments
POWER SUPPLIES
AV
DD
2.7/5.5 2.7/5.5 V min/V max
DV
DD
AV
DD
AV
DD
VP AVDD/6.0 AVDD/6.0 V min/V max AVDD ≤ VP ≤ 6.0 V. See Figure 25 and Figure 26.
I
DD5
(AI
DD
+ DI
DD
)
ADF4110 5.5 4.5 mA max 4.5 mA typical.
ADF4111 5.5 4.5 mA max 4.5 mA typical.
ADF4112
7.5
6.5
6.5 mA typical.
ADF4113 11 8.5 mA max 8.5 mA typical.
I
P
0.5 0.5 mA max T
A
= 25°C.
Low Power Sleep Mode 1 1 µA typ
NOISE CHARACTERISTICS
ADF4113 Normalized Phase Noise Floor6 215 −215 dBc/Hz typ
Phase Noise Performance
7
@ VCO output.
ADF4110: 540 MHz Output8 91 91 dBc/Hz typ @ 1 kHz offset and 200 kHz PFD frequency.
ADF4111: 900 MHz Output
9
87 87 dBc/Hz typ @ 1 kHz offset and 200 kHz PFD frequency.
ADF4112: 900 MHz Output9
90
90
@ 1 kHz offset and 200 kHz PFD frequency.
ADF4113: 900 MHz Output9 91 91 dBc/Hz typ @ 1 kHz offset and 200 kHz PFD frequency.
ADF4111: 836 MHz Output
10
78 78 dBc/Hz typ @ 300 Hz offset and 30 kHz PFD frequency.
ADF4112: 1750 MHz Output11 86 86 dBc/Hz typ @ 1 kHz offset and 200 kHz PFD frequency.
ADF4112: 1750 MHz Output
12
66 66 dBc/Hz typ @ 200 Hz offset and 10 kHz PFD frequency.
ADF4112: 1960 MHz Output
13
84 84 dBc/Hz typ @ 1 kHz offset and 200 kHz PFD frequency.
ADF4113: 1960 MHz Output13 85 85 dBc/Hz typ @ 1 kHz offset and 200 kHz PFD frequency.
ADF4113: 3100 MHz Output
14
86 86 dBc/Hz typ @ 1 kHz offset and 1 MHz PFD frequency.
Spurious Signals
ADF4110: 540 MHz Output9 97/106 97/106 dBc typ @ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4111: 900 MHz Output9 98/110 98/110 dBc typ @ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4112: 900 MHz Output
9
91/100 91/100 dBc typ @ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4113: 900 MHz Output9 100/110 100/110 dBc typ @ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4111: 836 MHz Output10 81/84 81/84 dBc typ @ 30 kHz/60 kHz and 30 kHz PFD frequency.
ADF4112: 1750 MHz Output
11
88/90 88/90 dBc typ @ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4112: 1750 MHz Output12 65/73 65/73 dBc typ @ 10 kHz/20 kHz and 10 kHz PFD frequency.
ADF4112: 1960 MHz Output
13
80/84 80/84 dBc typ @ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4113: 1960 MHz Output13
80/84
80/84
@ 200 kHz/400 kHz and 200 kHz PFD frequency.
ADF4113: 3100 MHz Output14 80/82 82/82 dBc typ @ 1 MHz/2 MHz and 1 MHz PFD frequency.
1The B chip specifications are given as typical values.
2This is the maximum operating frequency of the CMOS counters. The prescaler value should be chosen to ensure that the RF input is divided down to a frequency that
is less than this value.
3AC coupling ensures AVDD/2 bias. See Figure 33 for a typical circuit.
4Guaranteed by design.
5 TA = 25°C; AVDD = DVDD = 3 V; P = 16; SYNC = 0; DLY = 0; RFIN for ADF4110 = 540 MHz; RFIN for ADF4111, ADF4112, ADF4113 = 900 MHz.
6 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO, PNTOT, and subtracting 20logN (where N is the N divider
value) and 10logFPFD: PNSYNTH = PNTOT10logFPFD20logN.
7 The phase noise is measured with the EVAL-ADF411xEB1 evaluation board and the HP8562E spectrum analyzer. The spectrum analyzer provides the REFIN for the
synthesizer (fREFOUT = 10 MHz @ 0 dBm). SYNC = 0; DLY = 0 (Table 7).
8 fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 540 MHz; N = 2700; loop B/W = 20 kHz.
9 fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 900 MHz; N = 4500; loop B/W = 20 kHz.
10 fREFIN = 10 MHz; fPFD = 30 kHz; offset frequency = 300 Hz; fRF = 836 MHz; N = 27867; loop B/W = 3 kHz.
11 fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 1750 MHz; N = 8750; loop B/W = 20 kHz
12 fREFIN = 10 MHz; fPFD = 10 kHz; offset frequency = 200 Hz; fRF = 1750 MHz; N = 175000; loop B/W = 1 kHz.
13 fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 1960 MHz; N = 9800; loop B/W = 20 kHz.
14 fREFIN = 10 MHz; fPFD = 1 MHz; offset frequency = 1 kHz; fRF = 3100 MHz; N = 3100; loop B/W = 20 kHz.
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 5 of 28
TIMING CHARACTERISTICS
Guaranteed by design but not production tested. AVDD = DVDD = 3 V ± 10%, 5 V ± 10%; AVDD ≤ VP ≤ 6 V;
AGND = DGND = CPGND = 0 V; RSET = 4.7 kΩ; TA = TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter Limit at TMIN to TMAX (B Version) Unit Test Conditions/Comments
t1 10 ns min DATA to CLOCK setup time
t2 10 ns min DATA to CLOCK hold time
t3 25 ns min CLOCK high duration
t4 25 ns min CLOCK low duration
t5 10 ns min CLOCK to LE setup time
t6 20 ns min LE pulse width
CLOC
K
DATA
LE
LE
DB23 (MSB) DB22 DB2 DB1
(CONTROL BIT C2) DB0 (LSB)
(CONTROL BIT C1)
t
1
t
2
t
3
t
4
t
5
t
6
03496-002
Figure 2. Timing Diagram
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 6 of 28
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted
Table 3.
Parameter Rating
AV
DD
to GND1 0.3 V to +7 V
AV
DD
to DV
DD
0.3 V to +0.3 V
V
P
to GND 0.3 V to +7 V
V
P
to AV
DD
0.3 V to +5.5 V
Digital I/O Voltage to GND 0.3 V to V
DD
+ 0.3 V
Analog I/O Voltage to GND 0.3 V to V
P
+ 0.3 V
REF
IN
, RF
IN
A, RF
IN
B to GND 0.3 V to V
DD
+ 0.3 V
RF
IN
A to RF
IN
B ±320 mV
Operating Temperature Range
Industrial (B Version) 40°C to +85°C
Storage Temperature Range 65°C to +150°C
Maximum Junction Temperature 150°C
TSSOP θJA Thermal Impedance
150.4°C/W
LFCSP θJA Thermal Impedance
(Paddle Soldered)
122°C/W
LFCSP θJA Thermal Impedance
(Paddle Not Soldered)
216°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) 215°C
Infrared (15 sec) 220°C
1 GND = AGND = DGND = 0 V.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
This device is a high performance RF integrated circuit with an
ESD rating of <2 kV, and it is ESD sensitive. Proper precautions
should be taken for handling and assembly.
TRANSISTOR COUNT
6425 (CMOS) and 303 (Bipolar).
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 7 of 28
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
DV
DD
MUXOUT
LE
V
P
DATA
CLK
CE
DGND
R
SET
CP
CPGND
AGND
RF
IN
B
RF
IN
A
AV
DD
REF
IN
TOP VIEW
(Not to Scale)
ADF4110
ADF4111
ADF4112
ADF4113
03496-0-003
03496-0-004
NOTES
1. THE EXP OSED P ADDLE SHOULD BE CONNECT E D TO AGND.
14
13
12
1
3
4
LE
15 MUXOUT
DATA
CLK
11 CE
CPGND
AGND
2
AGND
RF
IN
B
5
RF
IN
A
7
AV
DD
6
AV
DD
8
REF
IN
9
DGND
10
DGND
19 R
SET
20 CP
18 V
P
17 DV
DD
16 DV
DD
ADF4110
ADF4111
ADF4112
ADF4113
TOP VI EW
(No t t o Scale)
Figure 3. TSSOP Pin Configuration Figure 4. LFCSP Pin Configuration
Table 4. Pin Function Descriptions
TSSOP
Pin No.
LFCSP
Pin No. Mnemonic Function
1 19 RSET Connecting a resistor bet
ween this pin and CPGND sets the maximum charge pump output current.
The nominal voltage potential at the RSET pin is 0.56 V. The relationship between ICP and RSET is
SET
maxCP R
I5.23
=
So, with R
SET
= 4.7 k, I
CPmax
= 5 mA.
2 20 CP Charge Pump Output. When enabled, this provides ±ICP to the external loop filter, which in turn
drives the external VCO.
3 1 CPGND Charge Pump Ground. This is the ground return path for the charge pump.
4 2, 3 AGND Analog Ground. This is the ground return path of the prescaler.
5 4 RFINB
Complementary Input to the RF Prescaler. This point should be decoupled to the ground plane with
a small bypass capacitor, typically 100 pF. See Figure 29.
6 5 RF
IN
A Input to the RF Prescaler. This small-signal input is ac-coupled from the VCO.
7 6, 7 AVDD Analog Power Supply. This may range from 2.7 V to 5.5 V. Decoupling capacitors to the analog ground
plane should be placed as close as possible to this pin. AV
DD
must be the same value as DV
DD
.
8 8 REFIN Reference Input. This is a CMOS input with a nominal threshold of VDD/2, and an equivalent input
resistance of 100 k. See Figure 28. This input can be driven from a TTL or CMOS crystal oscillator, or
can be ac-coupled.
9
9, 10
DGND
Digital Ground.
10 11 CE Chip Enable. A logic low on this pin powers down the device and puts the charge pump output into
three-state mode. Taking the pin high powers up the device depending on the status of the power-
down Bit F2.
11 12 CLK Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is
latched into the 24-bit shift register on the CLK rising edge. This input is a high impedance CMOS
input.
12 13 DATA Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This
input is a high impedance CMOS input.
13 14 LE Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into
one of the four latches; the latch is selected using the control bits.
14 15 MUXOUT This multiplexer output allows either the lock detect, the scaled RF, or the scaled reference
frequency to be accessed externally.
15 16, 17 DVDD Digital Power Supply. This may range from 2.7 V to 5.5 V. Decoupling capacitors to the digital ground
plane should be placed as close as possible to this pin. DV
DD
must be the same value as AV
DD
.
16 18 VP Charge Pump Power Supply. This should be greater than or equal to VDD. In systems where VDD is 3 V,
V
P
can be set to 6 V and used to drive a VCO with a tuning range of up to 6 V. 1
EPAD
Exposed Pad (LFCSP Only). The exposed paddle should be connected to AGND.
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 8 of 28
TYPICAL PERFORMANCE CHARACTERISTICS
FREQ PARAM DATA KEYWORD IMPEDANCE
–UNIT –TYPE –FORMAT –OHMS
GHz S MA R 50
FREQ MAGS11 ANGS11
1.05 0.9512 –40.134
1.10 0.93458 –43.747
1.15 0.94782 –44.393
1.20 0.96875 –46.937
1.25 0.92216 –49.6
1.30 0.93755 –51.884
1.35 0.96178 –51.21
1.40 0.94354 –53.55
1.45 0.95189 –56.786
1.50 0.97647 –58.781
1.55 0.98619 –60.545
1.60 0.95459 –61.43
1.65 0.97945 –61.241
1.70 0.98864 –64.051
1.75 0.97399 –66.19
1.80 0.97216 –63.775
FREQ MAGS11 ANGS11
0.05 0.89207 –2.0571
0.10 0.8886 –4.4427
0.15 0.89022 –6.3212
0.20 0.96323 –2.1393
0.25 0.90566 –12.13
0.30 0.90307 –13.52
0.35 0.89318 –15.746
0.40 0.89806 –18.056
0.45 0.89565 –19.693
0.50 0.88538 –22.246
0.55 0.89699 –24.336
0.60 0.89927 –25.948
0.65 0.87797 –28.457
0.70 0.90765 –29.735
0.75 0.88526 –31.879
0.80 0.81267 –32.681
0.85 0.90357 –31.522
0.90 0.92954 –34.222
0.95 0.92087 –36.961
1.00 0.93788 –39.343
03496-0-005
Figure 5. S-Parameter Data for the ADF4113 RF Input (up to 1.8 GHz)
–35
–30
–25
–20
–15
–10
–5
0
RF INPUT POWER (dBm)
0 1 2 3 4 5
RF INPUT FREQUENCY (GHz)
03496-0-006
V
DD
= 3V
V
P
= 3V
T
A
= +85°C
T
A
= +25°C
T
A
= –40°C
Figure 6. Input Sensitivity (ADF4113)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–2.0kHz –1.0kHz 900MHz 1.0kHz 2.0kHz
FREQUENCY
03496-0-007
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 s
AVERAGES = 19
REFERENCE
LEVEL = –4.2dBm
–91.0dBc/Hz
Figure 7. ADF4113 Phase Noise (900 MHz, 200 kHz, 20 kHz)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–2.0kHz –1.0kHz 900MHz 1.0kHz 2.0kHz
FREQUENCY
03496-0-008
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 s
AVERAGES = 19
REFERENCE
LEVEL = –4.2dBm
–92.5dBc/Hz
Figure 8. ADF4113 Phase Noise
(900 MHz, 200kHz, 20 kHz) with DLY and SYNC Enabled
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
PHASE NOISE (dBc/Hz)
FREQUENCY OFFSET FROM 900MHz CARRIER (Hz)
1k100 10k 100k 1M
03496-0-009
RMS NOISE = 0.52°
R
L
= –40dBc/Hz
Figure 9. ADF4113 Integrated Phase Noise
(900 MHz, 200 kHz, 20 kHz, Typical Lock Time: 400 µs)
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
PHASE NOISE (dBc/Hz)
FREQUENCY OFFSET FROM 900MHz CARRIER (Hz)
1k100 10k 100k 1M
03496-0-010
RMS NOISE = 0.62°
R
L
= –40dBc/Hz
Figure 10. ADF4113 Integrated Phase Noise
(900 MHz, 200 kHz, 35 kHz, Typical Lock Time: 200 µs)
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 9 of 28
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–400kHz –200kHz 900MHz 200kHz 400kHz
FREQUENCY
03496-0-011
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5s
AVERAGES = 30
REFERENCE
LEVEL = –4.2dBm
–90.2dBc/Hz
Figure 11. ADF4113 Reference Spurs (900 MHz, 200 kHz, 20 kHz)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–400kHz –200kHz 900MHz 200kHz 400kHz
FREQUENCY
03496-0-012
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 35kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5s
AVERAGES = 30
REFERENCE
LEVEL = –4.2dBm
–89.3dBc/Hz
Figure 12. ADF4113 (900 MHz, 200 kHz, 35 kHz)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–400Hz –200Hz 1750MHz 200Hz 400Hz
FREQUENCY
03496-0-013
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 3kHz
RES. BANDWIDTH = 10kHz
VIDEO BANDWIDTH = 10kHz
SWEEP = 477ms
AVERAGES = 10
REFERENCE
LEVEL = –8.0dBm
–75.2dBc/Hz
Figure 13. ADF4113 Phase Noise (1750 MHz, 30 kHz, 3 kHz)
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
PHASE NOISE (dBc/Hz)
FREQUENCY OFFSET FROM 1750MHz CARRIER (Hz)
1k100 10k 100k 1M
03496-0-014
RMS NOISE = 1.6°
R
L
= –40dBc/Hz
Figure 14. ADF4113 Integrated Phase Noise
(1750 MHz, 30 kHz, 3 kHz)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–80kHz –40kHz 1750MHz 40kHz 80kHz
FREQUENCY
03496-0-015
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 3kHz
RES. BANDWIDTH = 3Hz
VIDEO BANDWIDTH = 3Hz
SWEEP = 255s
POSITIVE PEEK DETECT
MODE
REFERENCE
LEVEL = –5.7dBm
–79.6dBc/Hz
Figure 15. ADF4113 Reference Spurs (1750 MHz, 30 kHz, 3 kHz)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–2.0kHz –1.0kHz 3100MHz 1.0kHz 2.0kHz
FREQUENCY
03496-0-016
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 1MHz
LOOP BANDWIDTH = 100kHz
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9s
AVERAGES = 45
REFERENCE
LEVEL = –4.2dBm
–86.6dBc/Hz
Figure 16. ADF4113 Phase Noise (3100 MHz, 1 MHz, 100 kHz)
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 10 of 28
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
PHASE NOISE (dBc/Hz)
FREQUENCY OFFSET FROM 3100MHz CARRIER (Hz)
10
3
10
2
10
4
10
5
10
6
03496-0-017
RMS NOISE = 1.7°
R
L
= 40dBc/Hz
Figure 17. ADF4113 Integrated Phase Noise
(3100 MHz, 1 MHz, 100 kHz)
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
OUTPUT POWER (dB)
–2.0MHz –1.0MHz 3100MHz 1.0MHz 2.0MHz
FREQUENCY
03496-0-018
V
DD
= 3V, V
P
= 5V
I
CP
= 5mA
PFD FREQUENCY = 1MHz
LOOP BANDWIDTH = 100kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 13s
AVERAGES = 1
REFERENCE
LEVEL = –17.2dBm
–80.6dBc/Hz
Figure 18. Reference Spurs (3100 MHz, 1 MHz, 100 kHz)
–180
–170
–160
–150
–140
–130
–120
PHASE NOISE (dBc/Hz)
PHASE DETECTOR FREQUENCY (kHz)
101 100 1000 10000
03496-0-019
V
DD
= 3V
V
P
= 5V
Figure 19. ADF4113 Phase Noise (Referred to CP Output)
vs. Phase Detector Frequency
PHASE NOISE (dBc/Hz)
–100
–90
–80
–70
–60
–40 –20 0 20 40 60 80 100
TEMPERATURE (°C)
03496-0-020
V
DD
= 3V
V
P
= 3V
Figure 20. ADF4113 Phase Noise vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
FIRST REFERENCE SPUR (dBc)
–100
–90
–80
–70
–60
–40 –20 0 20 40 60 80 100
TEMPERATURE (°C)
03496-0-021
V
DD
= 3V
V
P
= 5V
Figure 21. ADF4113 Reference Spurs vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
–105
–95
–85
–75
–65
–55
–45
–35
–25
–15
–5
FIRST REFERENCE SPUR (dBc)
0 1 2 3 4 5
TUNING VOLTAGE (V)
03496-0-022
V
DD
= 3V
V
P
= 5V
Figure 22. ADF4113 Reference Spurs (200 kHz) vs. VTUNE
(900 MHz, 200 kHz, 20 kHz)
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 11 of 28
PHASE NOISE (dBc/Hz)
–100
–90
–80
–70
–60
–40 –20 0 20 40 60 80 100
TEMPERATURE (°C)
03496-0-023
V
DD
= 3V
V
P
= 5V
Figure 23. ADF4113 Phase Noise vs. Temperature
(836 MHz, 30 kHz, 3 kHz)
FIRST REFERENCE SPUR (dBc)
–100
–90
–80
–70
–60
–40 –20 0 20 40 60 80 100
TEMPERATURE (°C)
03496-0-024
V
DD
= 3V
V
P
= 5V
Figure 24. ADF4113 Reference Spurs vs. Temperature
(836 MHz, 30 kHz, 3 kHz)
0
1
2
3
4
5
6
7
8
9
10
AI
DD
(mA)
PRESCALER VALUE
8/90 16/17 32/33 64/65
03496-0-025
ADF4113
ADF4112
ADF4110
ADF4111
Figure 25. AIDD vs. Prescaler Value
0
0.5
1.0
1.5
2.0
2.5
3.0
DI
DD
(mA)
PRESCALER OUTPUT FREQUENCY (MHz)
500 100 150 200
03496-0-026
V
DD
= 3V
V
P
= 3V
Figure 26. DIDD vs. Prescaler Output Frequency
(ADF4110, ADF4111, ADF4112, ADF4113)
–6
–4
–2
–3
–5
0
–1
I
CP
(mA)
2
1
4
3
6
5
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
V
CP
(V)
03496-0-027
V
PP
= 5V
I
CP
= 5mA
Figure 27. Charge Pump Output Characteristics for ADF4110 Family
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 12 of 28
CIRCUIT DESCRIPTION
REFERENCE INPUT SECTION
The reference input stage is shown in Figure 28. SW1 and SW2
are normally closed switches. SW3 is normally open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REFIN pin
on power-down.
BUFFER TO R COUNTER
REF
IN
100k
NC
SW2
SW3
NO
NC
SW1
POWER-DOWN
CONTROL
03496-0-028
Figure 28. Reference Input Stage
RF INPUT STAGE
The RF input stage is shown in Figure 29. It is followed by a
two-stage limiting amplifier to generate the current mode logic
(CML) clock levels needed for the prescaler.
AVDD
AGND
500500
1.6V
BIAS
GENERATOR
RFINA
RFINB
03496-0-029
Figure 29. RF Input Stage
PRESCALER (P/P + 1)
Along with the A and B counters, the dual-modulus prescaler
(P/P + 1) enables the large division ratio, N, to be realized (N =
BP + A). The dual-modulus prescaler, operating at CML levels,
takes the clock from the RF input stage and divides it down to a
manageable frequency for the CMOS A and B counters. The
prescaler is programmable; it can be set in software to 8/9,
16/17, 32/33, or 64/65. It is based on a synchronous 4/5 core.
A AND B COUNTERS
The A and B CMOS counters combine with the dual-modulus
prescaler to allow a wide ranging division ratio in the PLL
feedback counter. The counters are specified to work when the
prescaler output is 200 MHz or less. Thus, with an RF input
frequency of 2.5 GHz, a prescaler value of 16/17 is valid but a
value of 8/9 is not.
Pulse Swallow Function
The A and B counters, in conjunction with the dual-modulus
prescaler, make it possible to generate output frequencies that
are spaced only by the reference frequency divided by R. The
equation for the VCO frequency is
fVCO = [(P × B) + A]fREFIN/R
where:
fVCO = output frequency of external voltage controlled oscillator
(VCO)
P = preset modulus of dual-modulus prescaler
B = preset divide ratio of binary 13-bit counter(3 to 8191)
A = preset divide ratio of binary 6-bit swallow counter (0 to 63)
fREFIN = output frequency of the external reference frequency
oscillator
R = preset divide ratio of binary 14-bit programmable reference
counter (1 to 16383)
R COUNTER
The 14-bit R counter allows the input reference frequency to be
divided down to produce the reference clock to the phase
frequency detector (PFD). Division ratios from 1 to 16,383 are
allowed.
13-BIT B
COUNTER
6-BIT A
COUNTER
PRESCALER
P/P + 1
FROM RF
INPUT STAGE
MODULUS
CONTROL
N = BP + A
LOAD
LOAD
TO PFD
03496-0-030
Figure 30. A and B Counters
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 13 of 28
PHASE FREQUENCY DETECTOR (PFD) AND
CHARGE PUMP
The PFD takes inputs from the R counter and N counter (N =
BP + A) and produces an output proportional to the phase and
frequency difference between them. Figure 31 is a simplified
schematic. The PFD includes a programmable delay element
that controls the width of the antibacklash pulse. This pulse
ensures that there is no dead zone in the PFD transfer function
and minimizes phase noise and reference spurs. Two bits in the
reference counter latch, ABP2 and ABP1, control the width of
the pulse. See Table 7.
P
PROGRAMMABLE
DELAY U3
CLR2 Q2D2
U2
CLR1
Q1D1
CHARGE
PUMP
DOWN
UP
HI
HI
U1
ABP1 ABP2
R DIVIDER
N DIVIDER
CP OUTPUT
R DIVIDER
N DIVIDER
CP
CPGND
V
03496-0-031
Figure 31. PFD Simplified Schematic and Timing (In Lock)
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4110 family allows the user
to access various internal points on the chip. The state of
MUXOUT is controlled by M3, M2, and M1 in the function
latch. Table 9 shows the full truth table. Figure 32 shows the
MUXOUT section in block diagram form.
Lock Detect
MUXOUT can be programmed for two types of lock detect:
digital lock detect and analog lock detect.
Digital lock detect is active high. When LDP in the R counter
latch is set to 0, digital lock detect is set high when the phase
error on three consecutive phase detector (PD) cycles is less
than 15 ns. With LDP set to 1, five consecutive cycles of less
than 15 ns are required to set the lock detect. It stays high until
a phase error greater than 25 ns is detected on any subsequent
PD cycle.
The N-channel open-drain analog lock detect should be
operated with a 10 kΩ nominal external pull-up resistor. When
lock has been detected, this output is high with narrow low-
going pulses.
CONTROLMUX
DV
DD
MUXOUT
DGND
A
NALOG LOCK DETEC
T
DIGITAL LOCK DETECT
R COUNTER OUTPUT
N COUNTER OUTPUT
SDOUT
03496-0-032
Figure 32. MUXOUT Circuit
INPUT SHIFT REGISTER
The ADF4110 family digital section includes a 24-bit input shift
register, a 14-bit R counter, and a 19-bit N counter comprised of
a 6-bit A counter and a 13-bit B counter. Data is clocked into
the 24-bit shift register on each rising edge of CLK MSB first.
Data is transferred from the shift register to one of four latches
on the rising edge of LE. The destination latch is determined by
the state of the two control bits (C2, C1) in the shift register.
These are the two LSBs, DB1 and DB0, as shown in Figure 2.
The truth table for these bits is shown in Table 5.
Table 6 shows a summary of how the latches are programmed.
Table 5. C2, C1 Truth Table
Control Bits
C2 C1 Data Latch
0 0 R Counter
0 1 N Counter (A and B)
1 0 Function Latch (Including Prescaler)
1 1 Initialization Latch
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 14 of 28
Table 6. ADF4110 Family Latch Summary
N COUNTER LATCH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
B13 B12 B11 B8 B7 B6 B5 B4 B2 B1 A6 A5 A4 A3 A2 A1 C2 (0) C1 (1)B3
13-BIT B COUNTER CONTROL
BITS
RESERVED
DB2 DB1 DB0
G1 B10 B9
6-BIT A COUNTER
NIAGPC
FUNCTION LATCH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
CPI6 CPI5 CPI4 CPI1 TC4 TC3 TC2 TC1 F4 F3 F2 M3 M2 M1 PD1 F1 C2 (1) C1 (0)F5
TIMER COUNTER
CONTROL CONTROL
BITS
PRESCALER
VALUE
DB2 DB1 DB0
PD2 CPI3 CPI2
-REWOP 2NWOD
MUXOUT
CONTROL
CURRENT
SETTING
1
CURRENT
SETTING
2
KCOLTSAF EDOM
KCOLTSAF ELBANE
PC -EERHT ETATS
DP YTIRALOP
-REWOP 1NWOD
RETNUOC TESER
P1P2
INITIALIZATION LATCH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
CPI6 CPI5 CPI4 CPI1 TC4 TC3 TC2 TC1 F4 F3 F2 M3 M2 M1 PD1 F1 C2 (1) C1 (1)F5
TIMER COUNTER
CONTROL CONTROL
BITS
PRESCALER
VALUE
DB2 DB1 DB0
PD2 CPI3 CPI2
-REWOP 2NWOD
MUXOUT
CONTROL
CURRENT
SETTING
1
CURRENT
SETTING
2
KCOLTSAF EDOM
KCOLTSAF ELBANE
PC ETATS-EERHT
DP YTIRALOP
-REWOP 1NWOD
RETNUOC TESER
P1P2
TEST
MODE BITS
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
LDP T2 T1 R14 R13 R12 R11 R10 R8 R7 R6 R5 R4 R3 R2 R1 C2 (0) C1 (0)R9
14-BIT REFERENCE COUNTER, R CONTROL
BITS
DEVRESER
DB2 DB1 DB0
SYNCDLY ABP2 ABP1
ANTI-
BACKLASH
WIDTH
SYNC
DLY
KCOL TCETED NOISICERP
REFERENCE COUNTER LATCH
X
X X
X = DON'T CARE
X = DON'T CARE
03496-0-033
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 15 of 28
Table 7. Reference Counter Latch Map
OPERATION
LDP
THREE CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN
15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
FIVE CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN
15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
0
1
TEST MODE BITS SHOULD
BE SET TO 00 FOR NORMAL
OPERATION
R14
0
0
0
0
1
1
1
1
R13
0
0
0
0
1
1
1
1
R12
0
0
0
0
1
1
1
1
R3
0
0
0
1
1
1
1
1
R2
0
1
1
0
0
0
1
1
R1
1
0
1
0
0
1
0
1
DIVIDE RATIO
1
2
3
4
16380
16381
16382
16383
••••••••••
•••••••••
•••••••••
•••••••••
•••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
TEST
MODE BITS
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
LDP T2 T1 R14 R13 R12 R11 R10 R8 R7 R6 R5 R4 R3 R2 R1 C2 (0) C1 (0)R9
14-BIT REFERENCE COUNTER CONTROL
BITS
DEVRESER
DB2 DB1 DB0
SYNCDLY ABP2 ABP1
ANTI-
BACKLASH
WIDTH
SYNC
DLY
KCOL TCETED NOISICERP
ABP1ABP2
0
0
1
1
0
1
0
1
3.0ns
1.5ns
6.0ns
3.0ns
ANTIBACKLASH PULSE WIDTH
SYNCDLY
0
0
1
1
0
1
0
1
NORMAL OPERATION
OUTPUT OF PRESCALER IS RESYNCHRONIZED
WITH NONDELAYED VERSION OF RF INPUT
NORMAL OPERATION
OUTPUT OF PRESCALER IS RESYNCHRONIZED
WITH DELAYED VERSION OF RF INPUT
OPERATION
X
X = DON'T
CARE
03496-0-034
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 16 of 28
Table 8. AB Counter Latch Map
THESE BITS ARE NOT USED
BY THE DEVICE AND ARE
DON'T CARE BITS
A6
0
0
0
0
1
1
1
1
A5
0
0
0
0
1
1
1
1
A2
0
0
1
1
0
0
1
1
A1
0
1
0
1
0
1
0
1
A COUNTER
DIVIDE RATIO
0
1
2
3
60
61
62
63
••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
••••••••
•••••••••
•••••••••
B13
0
0
0
0
0
1
1
1
1
B12
0
0
0
0
0
1
1
1
1
B11
0
0
0
0
0
1
1
1
1
B3 B2 B1 B COUNTER DIVIDE RATIO
•••••••••
•••••••••
•••••••••
•••••••••
•••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
•••••••••
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
0
1
1
0
1
0
1
0
0
1
0
1
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
3
4
8188
8189
8190
8191
13-BIT B COUNTER
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
B13 B12 B11 B8 B7 B6 B5 B4 B2 B1 A6 A5 A4 A3 A2 A1B3
6-BIT A COUNTER
RESERVED
DB2
G1 B10 B9
NIAGPC
*SEE TABLE 9
F4 (FUNCTION LATCH)
FASTLOCK ENABLE* CP GAIN OPERATION
0
0
1
1
0
1
0
1
CHARGE PUMP CURRENT SETTING 1
IS PERMANENTLY USED.
CHARGE PUMP CURRENT SETTING 2
IS PERMANENTLY USED.
CHARGE PUMP CURRENT SETTING 1
IS USED.
CHARGE PUMP CURRENT IS SWITCHED
TO SETTING 2. THE TIME SPENT IN
SETTING 2 IS DEPENDENT UPON WHICH
FASTLOCK MODE IS USED. SEE FUNCTION
LATCH DESCRIPTION. N = BP + A, P IS PRESCALER VALUE SET IN THE
FUNCTION LATCH, B MUST BE GREATER THAN OR
EQUAL TO A. FOR CONTINUOUSLY ADJACENT VALUES
OF (N
X
F
REF
), AT THE OUTPUT, N
MIN
IS (P
2
–P).
X
X = DON'T CARE
X
C2 (0) C1 (1)
CONTROL
BITS
DB1 DB0
03496-0-035
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 17 of 28
Table 9. Function Latch Map
M3
0
0
0
0
1
1
1
1
M2
0
0
1
1
0
0
1
1
M1
0
1
0
1
0
1
0
1
OUTPUT
THREE-STATE OUTPUT
DIGITAL LOCK DETECT
(ACTIVE HIGH)
N DIVIDER OUTPUT
DV
DD
R DIVIDER OUTPUT
ANALOG LOCK DETECT
(N-CHANNEL OPEN-DRAIN)
SERIAL DATA OUTPUT
DGND
F1
0
1
COUNTER
OPERATION
NORMAL
R, A, B COUNTERS
HELD IN RESET
F2
0
1
PHASE DETECTOR
POLARITY
NEGATIVE
POSITIVE
F3
0
1
CHARGE PUMP OUTPUT
NORMAL
THREE-STATE
0
1
1
1
CE PIN
PD2 PD1 MODE
ASYNCHRONOUS POWER-DOWN
NORMAL OPERATION
ASYNCHRONOUS POWER-DOWN
SYNCHRONOUS POWER-DOWN
X
X
0
1
X
0
1
1
F5
X
0
1
FASTLOCK MODE
FASTLOCK DISABLED
FASTLOCK MODE 1
FASTLOCK MODE 2
F4
0
1
1
P1
0
1
0
1
PRESCALER VALUE
8/9
16/17
32/33
64/65
P2
0
0
1
1
CPI6
CPI3
CPI5
CPI2
CPI4
CPI1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
I
CP
(mA)
2.7k4.7k10k
1.09
2.18
3.26
4.35
5.44
6.53
7.62
8.70
0.63
1.25
1.88
2.50
3.13
3.75
4.38
5.00
0.29
0.59
0.88
1.76
1.47
1.76
2.06
2.35
CURRENT
SETTING
2
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
CPI6 CPI5 CPI4 CPI1
TC4 TC3 TC2 TC1
F4 F3 F2
M3 M2 M1
PD1
F1
C2(1) C1(0)
F5
CONTROL
BITS
PRESCALER
VALUE
DB2 DB1 DB0
PD2
P1
CPI3 CPI2
-REWOP 2NWOD
CURRENT
SETTING
1
TIMER COUNTER
CONTROL
KCOLTSAF EDOM
KCOLTSAF ELBANE
PC ETATS-EERHT
DP YTIRALOP
MUXOUT
CONTROL
-REWOP 1NWOD
RETNUOC TESER
P2
TC4
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
TC3
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
TC2
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
TC1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
TIMEOUT
(PFD CYCLES)
3
7
11
15
19
23
27
31
35
39
43
47
51
55
59
63
SEE FUNCTION LATCH,
TIMER COUNTER CONTROL
SECTION
03496-0-036
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 18 of 28
Table 10. Initialization Latch Map
M3
0
0
0
0
1
1
1
1
M2
0
0
1
1
0
0
1
1
M1
0
1
0
1
0
1
0
1
OUTPUT
THREE-STATE OUTPUT
DIGITAL LOCK DETECT
(ACTIVE HIGH)
N DIVIDER OUTPUT
DV
DD
R DIVIDER OUTPUT
ANALOG LOCK DETECT
(N-CHANNEL OPEN-DRAIN)
SERIAL DATA OUTPUT
DGND
TC4
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
TC3
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
TC2
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
TC1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
TIMEOUT
(PFD CYCLES)
3
7
11
15
19
23
27
31
35
39
43
47
51
55
59
63
F1
0
1
COUNTER
OPERATION
NORMAL
R, A, B COUNTERS
HELD IN RESET
F2
0
1
PHASE DETECTOR
POLARITY
NEGATIVE
POSITIVE
F3
0
1
CHARGE PUMP
OUTPUT NORMAL
THREE-STATE
0
1
1
1
CE PIN
PD2 PD1
MODE
ASYNCHRONOUS POWER-DOWN
NORMAL OPERATION
ASYNCHRONOUS POWER-DOWN
SYNCHRONOUS POWER-DOWN
X
X
0
1
X
0
1
1
F5
X
0
1
FASTLOCK MODE
FASTLOCK DISABLED
FASTLOCK MODE 1
FASTLOCK MODE 2
F4
0
1
1
P1
0
1
0
1
PRESCALER VALUE
8/9
16/17
32/33
64/65
P2
0
0
1
1
CPI6
CPI3
CPI5
CPI2
CPI4
CPI1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
I
CP
(mA)
2.7k4.7k10k
1.09
2.18
3.27
4.35
5.44
6.53
7.62
8.70
0.63
1.25
1.88
2.50
3.13
3.75
4.38
5.00
0.29
0.59
0.88
1.76
1.47
1.76
2.06
2.35
CURRENT
SETTING
2
DB23
DB22
DB21
DB20 DB19
DB18
DB17 DB16 DB15 DB14
DB12 DB11 DB10
DB9 DB8 DB7 DB6 DB5 DB4 DB3
DB13
CPI6 CPI5 CPI4
CPI1
TC4
TC3 TC2 TC1
F4 F3 F2
M3 M2 M1 PD1
F1
C2 (1) C1 (1)
F5
CONTROL
BITS
PRESCALER
VALUE
DB2 DB1 DB0
PD2
P1
CPI3 CPI2
-REWOP 2NWOD
CURRENT
SETTING
1
TIMER COUNTER
CONTROL
KCOLTSAF EDOM
KCOLTSAF ELBANE
PC ETATS-EERHT
DP YTIRALOP
MUXOUT
CONTROL
-REWOP 1NWOD
RETNUOC TESER
P2
SEE FUNCTION LATCH,
TIMER COUNTER CONTROL
SECTION
03496-0-037
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 19 of 28
FUNCTION LATCH
The on-chip function latch is programmed with C2, C1 set to 1.
Table 9 shows the input data format for programming the
function latch.
Counter Reset
DB2 (F1) is the counter reset bit. When DB2 is 1, the R counter
and the AB counters are reset. For normal operation, this bit
should be 0. Upon powering up, the F1 bit must be disabled,
and the N counter resumes counting in “close” alignment with
the R counter. (The maximum error is one prescaler cycle.)
Power-Down
DB3 (PD1) and DB21 (PD2) on the ADF411x provide
program-mable power-down modes. They are enabled by the
CE pin.
When the CE pin is low, the device is immediately disabled
regardless of the states of PD2, PD1.
In the programmed asynchronous power-down, the device
powers down immediately after latching a 1 into Bit PD1,
provided PD2 has been loaded with a 0.
In the programmed synchronous power-down, the device
power-down is gated by the charge pump to prevent unwanted
frequency jumps. Once power-down is enabled by writing a 1
into Bit PD1 (provided a 1 has also been loaded to PD2), the
device goes into power-down on the next charge pump event.
When a power-down is activated (either synchronous or
asynchronous mode including CE pin activated power-down),
the following events occur:
All active dc current paths are removed.
The R, N, and timeout counters are forced to their load
state conditions.
The charge pump is forced into three-state mode.
The digital clock detect circuitry is reset.
The RFIN input is debiased.
The reference input buffer circuitry is disabled.
The input register remains active and capable of loading
and latching data.
MUXOUT Control
The on-chip multiplexer is controlled by M3, M2, and M1 on
the ADF4110 family. Table 9 shows the truth table.
Fastlock Enable Bit
DB9 of the function latch is the fastlock enable bit. Fastlock is
enables only when this is 1.
Fastlock Mode Bit
DB10 of the function latch is the fastlock enable bit. When
fastlock is enabled, this bit determines which fastlock mode is
used. If the fastlock mode bit is 0, fastlock mode 1 is selected; if
the fastlock mode bit is 1, fastlock mode 2 is selected.
Fastlock Mode 1
The charge pump current is switched to the contents of Current
Setting 2.
The device enters fastlock by having a 1 written to the CP gain
bit in the AB counter latch. The device exits fastlock by having a
0 written to the CP gain bit in the AB counter latch.
Fastlock Mode 2
The charge pump current is switched to the contents of Current
Setting 2. The device enters fastlock by having a 1 written to the
CP gain bit in the AB counter latch. The device exits fastlock
under the control of the timer counter. After the timeout period
determined by the value in TC4 through TC1, the CP gain bit in
the AB counter latch is automatically reset to 0 and the device
reverts to normal mode instead of fastlock. See Table 9 for the
timeout periods.
Timer Counter Control
The user has the option of programming two charge pump cur-
rents. Current Setting 1 is meant to be used when the RF output
is stable and the system is in a static state. Current Setting 2 is
meant to be used when the system is dynamic and in a state of
change (i.e., when a new output frequency is programmed).
The normal sequence of events is as follows:
The user initially decides what the preferred charge pump
currents are going to be. For example, they may choose 2.5 mA
as Current Setting 1 and 5 mA as Current Setting 2.
At the same time, they must also decide how long they want the
secondary current to stay active before reverting to the primary
current. This is controlled by the timer counter control bits,
DB14 through DB11 (TC4 through TC1) in the function latch.
The truth table is given in Table 10.
A user can program a new output frequency simply by pro-
gramming the AB counter latch with new values for A and B. At
the same time, the CP gain bit can be set to 1, which sets the
charge pump with the value in CPI6CPI4 for a period deter-
mined by TC4 through TC1. When this time is up, the charge
pump current reverts to the value set by CPI3CPI1. At the
same time, the CP gain bit in the AB counter latch is reset to 0
and is ready for the next time the user wishes to change the
frequency.
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 20 of 28
Note that there is an enable feature on the timer counter. It is
enabled when Fastlock Mode 2 is chosen by setting the fastlock
mode bit (DB10) in the function latch to 1.
Charge Pump Currents
CPI3, CPI2, and CPI1 program Current Setting 1 for the charge
pump. CPI6, CPI5, and CPI4 program Current Setting 2 for the
charge pump. The truth table is given in Table 10.
Prescaler Value
P2 and P1 in the function latch set the prescaler values. The
prescaler value should be chosen so that the prescaler output
frequency is always less than or equal to 200 MHz. Thus, with
an RF frequency of 2 GHz, a prescaler value of 16/17 is valid but
a value of 8/9 is not.
PD Polarity
This bit sets the phase detector polarity bit. See Table 10.
CP Three-State
This bit controls the CP output pin. With the bit set high, the
CP output is put into three-state. With the bit set low, the CP
output is enabled.
INITIALIZATION LATCH
When C2, C1 = 1, 1, the initialization latch is programmed.
This is essentially the same as the function latch (programmed
when C2, C1 = 1, 0).
However, when the initialization latch is programmed, an addi-
tional internal reset pulse is applied to the R and AB counters.
This pulse ensures that the AB counter is at load point when the
AB counter data is latched, and the device begins counting in
close phase alignment.
If the latch is programmed for synchronous power-down (CE
pin high; PD1 bit high; PD2 bit low), the internal pulse also
triggers this power-down. The prescaler reference and the
oscillator input buffer are unaffected by the internal reset pulse,
so close phase alignment is maintained when counting resumes.
When the first AB counter data is latched after initialization, the
internal reset pulse is again activated. However, successive AB
counter loads after this will not trigger the internal reset pulse.
DEVICE PROGRAMMING AFTER INITIAL
POWER-UP
After initial power-up of the device, there are three ways to
program the device.
Initialization Latch Method
Apply VDD. Program the initialization latch (11 in 2 LSBs of
input word). Make sure the F1 bit is programmed to 0. Then, do
an R load (00 in 2 LSBs). Then do an AB load (01 in 2 LSBs).
When the initialization latch is loaded, the following occurs:
1. The function latch contents are loaded.
2. An internal pulse resets the R, A, B, and timeout counters
to load state conditions and three-states the charge pump.
Note that the prescaler band gap reference and the oscil-
lator input buffer are unaffected by the internal reset pulse,
allowing close phase alignment when counting resumes.
3. Latching the first AB counter data after the initialization
word activates the same internal reset pulse. Successive AB
loads do not trigger the internal reset pulse unless there is
another initialization.
CE Pin Method
1. Apply VDD.
2. Bring CE low to put the device into power-down. This is an
asynchronous power-down in that it happens immediately.
3. Program the function latch (10). Program the R counter
latch (00). Program the AB counter latch (01).
4. Bring CE high to take the device out of power-down. The R
and AB counters now resume counting in close alignment.
After CE goes high, a duration of 1 µs may be required for the
prescaler band gap voltage and oscillator input buffer bias to
reach steady state.
CE can be used to power the device up and down in order to
check for channel activity. The input register does not need to
be reprogrammed each time the device is disabled and enabled
as long as it has been programmed at least once after VDD was
initially applied.
Counter Reset Method
1. Apply VDD.
2. Do a function latch load (10 in 2 LSBs). As part of this,
load 1 to the F1 bit. This enables the counter reset.
3. Do an R counter load (00 in 2 LSBs). Do an AB counter
load (01 in 2 LSBs). Do a function latch load (10 in 2
LSBs). As part of this, load 0 to the F1 bit. This disables the
counter reset.
This sequence provides the same close alignment as the initiali-
zation method. It offers direct control over the internal reset.
Note that counter reset holds the counters at load point and
three states the charge pump but does not trigger synchronous
power-down. The counter reset method requires an extra
function latch load compared to the initialization latch method.
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 21 of 28
RESYNCHRONIZING THE PRESCALER OUTPUT
Table 7 (the Reference Counter Latch Map) shows two bits,
DB22 and DB21, which are labeled DLY and SYNC,
respectively. These bits affect the operation of the prescaler.
With SYNC = 1, the prescaler output is resynchronized with the
RF input. This has the effect of reducing jitter due to the
prescaler and can lead to an overall improvement in synthesizer
phase noise performance. Typically, a 1 dB to 2 dB
improvement is seen in the ADF4113. The lower bandwidth
devices can show an even greater improvement. For example,
the ADF4110 phase noise is typically improved by 3 dB when
SYNC is enabled.
With DLY = 1, the prescaler output is resynchronized with a
delayed version of the RF input.
If the SYNC feature is used on the synthesizer, some care must
be taken. At some point, (at certain temperatures and output
frequencies), the delay through the prescaler coincides with the
active edge on RF input; this causes the SYNC feature to break
down. It is important to be aware of this when using the SYNC
feature. Adding a delay to the RF signal, by programming
DLY = 1, extends the operating frequency and temperature
somewhat. Using the SYNC feature also increases the value of
the AIDD for the device. With a 900 MHz output, the ADF4113
AIDD increases by about 1.3 mA when SYNC is enabled and by
an additional 0.3 mA if DLY is enabled.
All the typical performance plots in this data sheet, except for
Figure 8, apply for DLY and SYNC = 0, i.e., no resynchroniza-
tion or delay enabled.
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 22 of 28
APPLICATIONS
LOCAL OSCILLATOR FOR GSM BASE STATION TRANSMITTER
Figure 33 shows the ADF4111/ADF4112/ADF4113 being used
with a VCO to produce the LO for a GSM base station
transmitter.
The reference input signal is applied to the circuit at FREFIN
and, in this case, is terminated in 50 Ω. A typical GSM system
would have a 13 MHz TCXO driving the reference input with-
out any 50 Ω termination. In order to have channel spacing of
200 kHz (GSM standard), the reference input must be divided
by 65, using the on-chip reference divider of the ADF4111/
ADF4112/ADF4113.
The charge pump output of the ADF4111/ADF4112/ADF4113
(Pin 2) drives the loop filter. In calculating the loop filter
component values, a number of items need to be considered. In
this example, the loop filter was designed so that the overall
phase margin for the system would be 45 degrees. Other PLL
system specifications are
KD = 5 mA
KV = 12 MHz/V
Loop Bandwidth = 20 kHz
FREF = 200 kHz
N = 4500
Extra Reference Spur Attenuation = 10 dB
All of these specifications are needed and used to come up with
the loop filter component values shown in Figure 33.
The loop filter output drives the VCO, which in turn is fed back
to the RF input of the PLL synthesizer. It also drives the RF out-
put terminal. A T-circuit configuration provides 50 matching
between the VCO output, the RF output, and the RFIN terminal
of the synthesizer.
In a PLL system, it is important to know when the system is in
lock. In Figure 33, this is accomplished by using the MUXOUT
signal from the synthesizer. The MUXOUT pin can be pro-
grammed to monitor various internal signals in the synthesizer.
One of these is the LD or lock-detect signal.
ADF4111
ADF4112
ADF4113
CE
CLK
DATA
LE
1000pF 1000pF REF
IN
100pF
CP
MUXOUT
CPGND
AGND
DGND
1nF
8.2nF
620pF
100pF
511
3.3k
5.6k
100pF
18
1
TO BE USED WHEN GENERATOR SOURCE IMPEDANCE IS 50.
2
OPTIONAL MATCHING RESISTOR DEPENDING ON RF
OUT
FREQUENCY.
DECOUPLING CAPACITORS ON AV
DD
, DV
DD
, AND V
P
OF THE ADF411x
AND ON THE POSITIVE SUPPLY OF THE VCO190-902T HAVE BEEN
OMITTED FROM THE DIAGRAM TO INCREASE CLARITY.
SPI COMPATIBLE SERIAL BUS
R
SET
RF
IN
A
RF
IN
B
AV
DD
DV
DD
V
P
FREF
IN
V
DD
V
P
LOCK
DETECT
V
CC
VCO190-902T 18
18
100pF
RF
OUT
4.7k
715 16
8
2
14
6
5
1
9
4
3
B
CP
51
2
03496-0-038
Figure 33. Local Oscillator for GSM Base Station
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 23 of 28
ADF4111
ADF4112
ADF4113
2.7k
VCO
GND
18
100pF
100pF
18
18
RFOUT
FREFIN
51
100pF
100pF
RFINA
RFINB
POWER SUPPLY CONNECTIONS AND DECOUPLING
CAPACITORS ARE OMITTED FOR CLARITY.
RSET
REFIN CP LOOP
FILTER
CE
CLK
DATA
LE
SPI COMPATIBLE SERIAL BUS
AD5320
12-BIT
V-OUT DAC
MUXOUT LOCK
DETECT
INPUT OUTPUT
2
14
6
5
1
8
03496-0-039
Figure 34. Driving the RSET Pin with a D/A Converter
USING A D/A CONVERTER TO DRIVE THE RSET PIN
A D/A converter can be used to drive the RSET pin of the
ADF4110 family, thus increasing the level of control over the
charge pump current, ICP. This can be advantageous in wide-
band applications where the sensitivity of the VCO varies over
the tuning range. To compensate for this, the ICP may be varied
to maintain good phase margin and ensure loop stability. See
Figure 34.
SHUTDOWN CIRCUIT
The attached circuit in Figure 35 shows how to shut down both
the ADF4110 family and the accompanying VCO. The ADG701
switch goes closed circuit when a Logic 1 is applied to the IN
input. The low cost switch is available in both SOT-23 and
MSOP packages.
WIDEBAND PLL
Many of the wireless applications for synthesizers and VCOs in
PLLs are narrow band in nature. These applications include the
various wireless standards like GSM, DSC1800, CDMA, and
WCDMA. In each of these cases, the total tuning range for the
local oscillator is less than 100 MHz. However, there are also
wideband applications for which the local oscillator could have
a tuning range as wide as an octave. For example, cable TV
tuners have a total range of about 400 MHz. Figure 36 shows an
application where the ADF4113 is used to control and program
the Micronetics M3500-2235. The loop filter was designed for
an RF output of 2900 MHz, a loop bandwidth of 40 kHz, a PFD
frequency of 1 MHz, ICP of 10 mA (2.5 mA synthesizer ICP
multiplied by the gain factor of 4), VCO KD of 90 MHz/V
(sensitivity of the M3500-2235 at an output of 2900 MHz), and
a phase margin of 45°C.
In narrow-band applications, there is generally a small variation
in output frequency (generally less than 10%) and a small
variation in VCO sensitivity over the range (typically 10% to
15%). However, in wideband applications, both of these
parameters have a much greater variation. In Figure 36, for
example, there is a 25% and +17% variation in the RF output
from the nominal 2.9 GHz. The sensitivity of the VCO can vary
from 120 MHz/V at 2750 MHz to 75 MHz/V at 3400 MHz
(+33%, 17%). Variations in these parameters change the loop
bandwidth. This in turn can affect stability and lock time. By
changing the programmable ICP, it is possible to get compensa-
tion for these varying loop conditions and ensure that the loop
is always operating close to optimal conditions.
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 24 of 28
V
DD
V
P
AV
DD
DV
DD
ADF4110
ADF4111
ADF4112
ADF4113
V
P
4.7k
VCO
V
CC
GND
1818
18
100pF
100pF
RF
OUT
REF
IN
51
100pF
100pF
DNGPC
DNGA
DNGD
RF
IN
A
RF
IN
B
DECOUPLING CAPACITORS AND INTERFACE SIGNALS HAVE
BEEN OMITTED FROM THE DIAGRAM TO INCREASE CLARITY.
R
SET
CP
CE
POWER-DOWN CONTROL V
DD
S
IN
DGND
LOOP
FILTER
ADG701
FREF
IN
1
8
715 16
2
6
5
9
43
10
03496-0-040
Figure 35. Local Oscillator Shutdown Circuit
VDD VP
AVDD DVDD
ADF4113
VP
2.8nF
680
130pF
3.3k
19nF
M3500-2235
VCC 1818
18
100pF
100pF
RFOUT
1000pF 1000pF
51
REFIN
MUXOUT LOCK
DETECT
51
100pF
100pF
DNGPC
DNGA
DNGD
RFINA
RFINB
CE
CLK
DATA
LE
SUBLAIRESELBITAPMOC-IPS
DECOUPLING CAPACITORS ON AV
DD
, DV
DD
, V
P
OF THE ADF4113
AND ON VCC OF THE M3500-2250 HAVE BEEN OMITTED FROM
THE DIAGRAM TO AID CLARITY.
RSET
CP
4.7k
12V
V_TUNE
GND
20V
1k
AD820
3k
OUT
FREFIN
3 4 9
5
6
14
2
1
8
7 15 16
03496-0-041
Figure 36. Wideband Phase-Locked Loop
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 25 of 28
DIRECT CONVERSION MODULATOR
In some applications, a direct conversion architecture can be
used in base station transmitters. Figure 37 shows the combina-
tion available from ADI to implement this solution.
The circuit diagram shows the AD9761 being used with the
AD8346. The use of dual integrated DACs such as the AD9761
with specified ±0.02 dB and ±0.004 dB gain and offset matching
characteristics ensures minimum error contribution (over
temperature) from this portion of the signal chain.
The local oscillator (LO) is implemented using the ADF4113. In
this case, the OSC 3B1-13M0 provides the stable 13 MHz
reference frequency. The system is designed for a 200 kHz
channel spacing and an output center frequency of 1960 MHz.
The target application is a WCDMA base station transmitter.
Typical phase noise performance from this LO is 85 dBc/Hz at
a 1 kHz offset.
The LO port of the AD8346 is driven in single-ended fashion.
LOIN is ac-coupled to ground with the 100 pF capacitor; LOIP
is driven through the ac coupling capacitor from a 50 source.
An LO drive level of between 6 dBm and 12 dBm is required.
The circuit of Figure 37 gives a typical level of 8 dBm.
The RF output is designed to drive a 50 Ω load but must be ac-
coupled as shown in Figure 37. If the I and Q inputs are driven
in quadrature by 2 V p-p signals, the resulting output power is
around 10 dBm.
RSET
ADF4113
18
100pF
18
REFIN
100pF
RFINARFINB
CP
SERIAL
DIGITAL
INTERFACE
TCXO
OSC 3B1-13M0
100pF
620pF
3.9k
3.3k
9.1nF
4.7k
18
100pF RF
OUT
POWER SUPPLY CONNECTIONS AND DECOUPLING CAPACITORS
ARE OMITTED FROM DIAGRAM TO INCREASE CLARITY.
AD9761
TxDAC
REFIO
FS ADJ
MODULATED
DIGITAL
DATA
QOUTB
IOUTA
IOUTB
QOUTA
AD8346
LOIN LOIP
VOUT
100pF 100pF
2k
51
910pF VCO190-1960T
IBBP
IBBN
QBBP
QBBN
LOW-PASS
FILTER
LOW-PASS
FILTER
03496-0-042
Figure 37. Direct Conversion Transmitter Solution
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 26 of 28
INTERFACING
The ADF4110 family has a simple SPI® compatible serial inter-
face for writing to the device. SCLK, SDATA, and LE control the
data transfer. When latch enable (LE) goes high, the 24 bits that
have been clocked into the input register on each rising edge of
SCLK get transferred to the appropriate latch. See Figure 2 for
the timing diagram and Table 5 for the latch truth table.
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible for the device is
833 kHz, or one update every 1.2 µs. This is certainly more than
adequate for systems that have typical lock times in the
hundreds of microseconds.
ADuC812 Interface
Figure 38 shows the interface between the ADF4110 family and
the ADuC812 MicroConverter®. Since the ADuC812 is based
on an 8051 core, this interface can be used with any 8051 based
microcontroller. The MicroConverter is set up for SPI master
mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF4110 family
needs a 24-bit word. This is accomplished by writing three 8-bit
bytes from the MicroConverter to the device. When the third
byte has been written, the LE input should be brought high to
complete the transfer.
When power is first applied to the ADF4110 family, three writes
are needed (one each to the R counter latch, N counter latch,
and initialization latch) for the output to become active.
I/O port lines on the ADuC812 are also used to control power-
down (CE input), and to detect lock (MUXOUT configured as
lock detect and polled by the port input).
When the ADuC812 is operating in the mode described above,
the maximum SCLOCK rate of the ADuC812 is 4 MHz. This
means that the maximum rate at which the output frequency
can be changed is 166 kHz.
SCLOCK
MOSI
I/O PORTS
ADuC812
SCLK
SDATA
LE
CE
MUXOUT
(LOCK DETECT)
ADF4110
ADF4111
ADF4112
ADF4113
03496-0-043
Figure 38. ADuC812 to ADF4110 Family Interface
ADSP-2181 Interface
Figure 39 shows the interface between the ADF4110 family and
the ADSP-21xx digital signal processor. The ADF4110 family
needs a 24-bit serial word for each latch write. The easiest way
to accomplish this using the ADSP-21xx family is to use the
auto buffered transmit mode of operation with alternate
framing. This provides a means for transmitting an entire block
of serial data before an interrupt is generated.
SCLK
DT
I/O FLAGS
ADSP-21xx
SCLK
SDATA
LE
CE
MUXOUT
(LOCK DETECT)
ADF4110
ADF4111
ADF4112
ADF4113
TFS
03496-0-044
Figure 39. ADSP-21xx to ADF4110 Family Interface
Set up the word length for 8 bits and use three memory
locations for each 24-bit word. To program each 24-bit latch,
store the three 8-bit bytes, enable the auto buffered mode, and
then write to the transmit register of the DSP. This last opera-
tion initiates the autobuffer transfer.
PCB DESIGN GUIDELINES FOR CHIP SCALE
PACKAGE
The lands on the chip scale package (CP-20) are rectangular.
The printed circuit board pad for these should be 0.1 mm
longer than the package land length and 0.05 mm wider than
the package land width. The land should be centered on the
pad. This ensures that the solder joint size is maximized.
The bottom of the chip scale package has a central thermal pad.
The thermal pad on the printed circuit board should be at least
as large as this exposed pad. On the printed circuit board, there
should be a clearance of at least 0.25 mm between the thermal
pad and the inner edges of the pad pattern. This ensures that
shorting is avoided.
Thermal vias may be used on the printed circuit board thermal
pad to improve thermal performance of the package. If vias are
used, they should be incorporated in the thermal pad at 1.2 mm
pitch grid. The via diameter should be between 0.3 mm and
0.33 mm, and the via barrel should be plated with 1 oz. copper
to plug the via.
The user should connect the printed circuit board thermal pad
to AGND.
Data Sheet ADF4110/ADF4111/ADF4112/ADF4113
Rev. E | Page 27 of 28
OUTLINE DIMENSIONS
0.50
BSC
0.65
0.60
0.55
0.30
0.25
0.18
COMPLIANT
TO
JEDEC STANDARDS MO-220-WGGD-1.
BOTTOM VIEWTOP VIEW
EXPOSED
PAD
PIN1
INDICATOR
4.10
4.00 SQ
3.90
SEATING
PLANE
0.80
0.75
0.70 0.05 MAX
0.02 NOM
0.20 REF
0.20 MIN
COPLANARITY
0.08
PIN 1
INDICATOR
2.30
2.10 SQ
2.00
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
1
20
6
10
11
1516
5
08-16-2010-B
Figure 40. 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-20-6)
Dimensions shown in millimeters
16 9
81
PIN 1
SEATING
PLANE
4.50
4.40
4.30
6.40
BSC
5.10
5.00
4.90
0.65
BSC
0.15
0.05
1.20
MAX 0.20
0.09 0.75
0.60
0.45
0.30
0.19
COPLANARITY
0.10
COM P LIANT T O JEDEC S TANDARDS M O-153- AB
Figure 41. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ADF4110/ADF4111/ADF4112/ADF4113 Data Sheet
Rev. E | Page 28 of 28
ORDERING GUIDE
Model1
Temperature Range
Package Description
Package Option2
ADF4110BCPZ 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4110BCPZ-RL 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4110BCPZ-RL7 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4110BRU 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4110BRU-REEL 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4110BRU-REEL7 -40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4110BRUZ 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4110BRUZ-RL 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4110BRUZ-RL7 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4111BCPZ
–40°C to +85°C
20-Lead Frame Chip Scale Package [LFCSP_WQ]
CP-20-6
ADF4111BCPZ-RL 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4111BCPZ-RL7 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4111BRU 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4111BRUZ 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4111BRUZ-RL 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4111BRUZ-RL7 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4112BCPZ 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4112BCPZ-RL 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4112BCPZ-RL7 –40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4112BRU 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4112BRU-REEL7 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4112BRUZ 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4112BRUZ-REEL 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4112BRUZ-REEL7
40°C to +85°C
16-Lead Thin Shrink Small Outline Package [TSSOP]
RU-16
ADF4113BCPZ 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4113BCPZ-RL
40°C to +85°C
20-Lead Frame Chip Scale Package [LFCSP_WQ]
CP-20-6
ADF4113BCPZ-RL7 40°C to +85°C 20-Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
ADF4113BRU 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4113BRU-REEL7 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4113BRUZ 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4113BRUZ-REEL 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4113BRUZ-REEL7 40°C to +85°C 16-Lead Thin Shrink Small Outline Package [TSSOP] RU-16
ADF4113BCHIPS 40°C to +85°C DIE
EVAL-ADF4113EBZ1 Evaluation Board
EVAL-ADF4113EBZ2 Evaluation Board
EVAL-ADF411XEB1 Evaluation Board
1 Z = RoHS Compliant Part.
2 CP-20-6 package was formerly CP-20-1 package.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03496-0-8/12(E)