DS90CP22 DS90CP22 800 Mbps 2x2 LVDS Crosspoint Switch Literature Number: SNLS053D DS90CP22 800 Mbps 2x2 LVDS Crosspoint Switch General Description Features DS90CP22 is a 2x2 crosspoint switch utilizing LVDS (Low Voltage Differential Signaling) technology for low power, high speed operation. Data paths are fully differential from input to output for low noise generation and low pulse width distortion. The non-blocking design allows connection of any input to any output or outputs. LVDS I/O enable high speed data transmission for point-to-point interconnects. This device can be used as a high speed differential crosspoint, 2:1 mux, 1:2 demux, repeater or 1:2 signal splitter. The mux and demux functions are useful for switching between primary and backup circuits in fault tolerant systems. The 1:2 signal splitter and 2:1 mux functions are useful for distribution of serial bus across several rack-mounted backplanes. The DS90CP22 accepts LVDS signal levels, LVPECL levels directly or PECL with attenuation networks. The individual LVDS outputs can be put into TRI-STATE by use of the enable pins. For more details, please refer to the Application Information section of this datasheet. DC - 800 Mbps low jitter, low skew operation 65 ps (typ) of pk-pk jitter with PRBS = 223-1 data pattern at 800 Mbps Single +3.3 V Supply Less than 330 mW (typ) total power dissipation Non-blocking "'Switch Architecture"' Balanced output impedance Output channel-to-channel skew is 35 ps (typ) Configurable as 2:1 mux, 1:2 demux, repeater or 1:2 signal splitter LVDS receiver inputs accept LVPECL signals Fast switch time of 1.2ns (typ) Fast propagation delay of 1.3ns (typ) Receiver input threshold < 100 mV Available in 16 lead TSSOP and SOIC packages Conforms to ANSI/TIA/EIA-644-1995 LVDS standard Operating Temperature: -40C to +85C Connection Diagrams 10105305 Order Number DS90CP22M-8 (SOIC) Order Number DS90CP22MT (TSSOP) 10105310 Diff. Output Eye-Pattern in 1:2 split mode @ 800 Mbps Conditions: 3.3 V, PRBS = 223-1 data pattern, VID = 300mV, VCM = +1.2 V, 200 ps/div, 100 mV/div (c) 2007 National Semiconductor Corporation 101053 www.national.com DS90CP22 800 Mbps 2x2 LVDS Crosspoint Switch December 5, 2007 DS90CP22 16L SOIC 16L SOIC Package Derating 16L TSSOP 16L TSSOP Package Derating ESD Rating: Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) -0.3V to +4V CMOS/TTL Input Voltage (EN0, -0.3V to (VCC + 0.3V) EN1, SEL0, SEL1) LVDS Receiver Input Voltage (IN +, IN-) -0.3V to +4V LVDS Driver Output Voltage (OUT +, OUT-) -0.3V to +4V LVDS Output Short Circuit Current Continuous Junction Temperature +150C Storage Temperature Range -65C to +150C Lead Temperature (Soldering, 4 sec.) +260C Maximum Package Power Dissipation at 25C 1.435 W 11.48 mW/C above +25C 0.866 W 9.6 mW/C above +25C > 5 kV (HBM, 1.5k, 100pF) > 250 V (EIAJ, 0, 200pF) Recommended Operating Conditions Supply Voltage (VCC) Receiver Input Voltage Operating Free Air Temperature Min Typ Max Unit s 3.0 3.3 3.6 V 0 VCC V -40 +25 +85 C Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified Symbol Parameter Conditions Min Typ Max Units VCC V CMOS/TTL DC SPECIFICATIONS (EN0,EN1,SEL0,SEL1) VIH High Level Input Voltage 2.0 VIL Low Level Input Voltage 0.8 V IIH High Level Input Current VIN = 3.6V or 2.0V; VCC = 3.6V +7 +20 A IIL Low Level Input Current VIN = 0V or 0.8V; VCC = 3.6V 1 10 A VCL Input Clamp Voltage ICL = -18 mA -0.8 -1.5 V GND LVDS OUTPUT DC SPECIFICATIONS (OUT0,OUT1) VOD Differential Output Voltage RL = 75 270 365 475 mV RL = 75, VCC = 3.3V, TA = 25C 285 365 440 mV 35 mV 1.0 1.2 1.45 V 35 mV 1 10 A VOD Change in VOD between Complimentary Output States VOS Offset Voltage (Note 3) VOS Change in VOS between Complimentary Output States IOZ Output TRI-STATE(R) Current TRI-STATE Output, VOUT = VCC or GND IOFF Power-Off Leakage Current VCC = 0V; VOUT = 3.6V or GND 1 10 A IOS Output Short Circuit Current VOUT+ OR VOUT- = 0V -15 -25 mA IOSB Both Outputs Short Circuit Current VOUT+ AND VOUT- = 0V -30 -50 mA 0 +100 mV LVDS RECEIVER DC SPECIFICATIONS (IN0,IN1) VTH Differential Input High Threshold VCM = +0.05V or +1.2V or +3.25V, VTL Differential Input Low Threshold Vcc = 3.3V -100 VCMR Common Mode Voltage Range VID = 100mV, Vcc = 3.3V 0.05 IIN Input Current VIN = +3.0V, VCC = 3.6V or 0V VIN = 0V, VCC = 3.6V or 0V 0 mV 3.25 V 1 10 A 1 10 A SUPPLY CURRENT ICCD Total Supply Current RL = 75, CL = 5 pF, EN0 = EN1 = High 98 125 mA ICCZ TRI-STATE Supply Current EN0 = EN1 = Low 43 55 mA Note 1: "Absolute Maximum Ratings" are these beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of "Electrical Characteristics" provides conditions for actual device operation. Note 2: All typical are given for VCC = +3.3V and TA = +25C, unless otherwise stated. Note 3: VOS is defined and measured on the ATE as (VOH + VOL) / 2. www.national.com 2 Over recommended operating supply and temperature ranges unless otherwise specified (Note 4) Symbol Min Typ TSET Input to SEL Setup Time, Figures 1, 2 (Note 5) 0.7 0.5 ns THOLD Input to SEL Hold Time, Figures 1, 2 (Note 5) 1.0 0.5 ns TSWITCH SEL to Switched Output, Figures 1, 2 0.9 1.2 1.7 ns TPHZ Disable Time (Active to TRI-STATE) High to Z, Figure 3 2.1 4.0 ns TPLZ Disable Time (Active to TRI-STATE) Low to Z, Figure 3 3.0 4.5 ns TPZH Enable Time (TRI-STATE to Active) Z to High, Figure 3 25.5 55.0 ns TPZL Enable Time (TRI-STATE to Active) Z to Low, Figure 3 25.5 55.0 ns TLHT Output Low-to-High Transition Time, 20% to 80%, Figure 5 290 400 580 ps THLT Output High-to-Low Transition Time, 80% to 20%, Figure 5 290 TJIT LVDS Data Path Peak to Peak Jitter, (Note 6) TPLHD Parameter Units 400 580 ps 40 90 ps VID = 300mV; PRBS=223-1 data pattern; VCM = 1.2V at 800Mbps 65 120 ps 0.9 1.3 1.6 ns 1.0 1.3 1.5 ns 0.9 1.3 1.6 ns 1.0 1.3 1.5 ns VCC = 3.3V, TA = 25C Propagation High to Low Delay, Figure 6 Propagation High to Low Delay, Figure 6 Max VID = 300mV; 50% Duty Cycle; VCM = 1.2V at 800Mbps Propagation Low to High Delay, Figure 6 Propagation Low to High Delay, Figure 6 TPHLD Conditions VCC = 3.3V, TA = 25C TSKEW Pulse Skew |TPLHD - TPHLD| 0 225 ps TCCS Output Channel-to-Channel Skew, Figure 7 35 80 ps Note 4: The parameters are guaranteed by design. The limits are based on statistical analysis of the device performance over PVT (process, voltage and temperature) range. Note 5: TSET and THOLD time specify that data must be in a stable state before and after the SEL transition. Note 6: The parameters are guaranteed by design. The limits are based on statistical analysis of the device performance over PVT range with the following equipment test setup: HP70004A (display mainframe) with HP70841B (pattern generator), 5 feet of RG-142 cable with DUT test board and HP83480A (digital scope mainframe) with HP83483A (20GHz scope module). 3 www.national.com DS90CP22 AC Electrical Characteristics DS90CP22 AC Timing Diagrams 10105302 FIGURE 1. Input-to-Select rising edge setup and hold times and mux switch time 10105303 FIGURE 2. Input-to-Select falling edge setup and hold times and mux switch time 10105304 FIGURE 3. Output active to TRI-STATE and TRI-STATE to active output time www.national.com 4 DS90CP22 10105306 FIGURE 4. LVDS Output Load 10105309 FIGURE 5. LVDS Output Transition Time 10105307 FIGURE 6. Propagation Delay Low-to-High and High-to-Low 10105308 FIGURE 7. Output Channel-to-Channel Skew in 1:2 splitter mode 5 www.national.com DS90CP22 DS90CP22 Pin Descriptions Pin Name # of Pin Input/Output IN+ 2 I Non-inverting LVDS input Description IN - 2 I Inverting LVDS input OUT+ 2 O Non-inverting LVDS Output OUT - 2 O Inverting LVDS Output EN 2 I A logic low on the Enable puts the LVDS output into TRISTATE and reduces the supply current SEL 2 I 2:1 mux input select GND 1 P Ground VCC 1 P Power Supply NC 2 No Connect PCB LAYOUT AND POWER SYSTEM BYPASS Circuit board layout and stack-up for the DS90CP22 should be designed to provide noise-free power to the device. Good layout practice also will separate high frequency or high level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (4 to 10 mils) for power/ground sandwiches. This increases the intrinsic capacitance of the PCB power system which improves power supply filtering, especially at high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range 0.01 F to 0.1 F. It is recommended practice to use two vias at each power pin of the DS90CP22 as well as all RF bypass capacitor terminals. Dual vias reduce the interconnect inductance by up to half, thereby reducing interconnect inductance and extending the effective frequency range of the bypass components. The outer layers of the PCB may be flooded with additional ground plane. These planes will improve shielding and isolation as well as increase the intrinsic capacitance of the power supply plane system. Naturally, to be effective, these planes must be tied to the ground supply plane at frequent intervals with vias. Frequent via placement also improves signal integrity on signal transmission lines by providing short paths for image currents which reduces signal distortion. There are more common practices which should be followed when designing PCBs for LVDS signaling. Please see Application Note: AN-1108 for additional information. Application Information MODES OF OPERATION The DS90CP22 provides three modes of operation. In the 1:2 splitter mode, the two outputs are copies of the same single input. This is useful for distribution / fan-out applications. In the repeater mode, the device operates as a 2 channel LVDS buffer. Repeating the signal restores the LVDS amplitude, allowing it to drive another media segment. This allows for isolation of segments or long distance applications. The switch mode provides a crosspoint function. This can be used in a system when primary and redundant paths are supported in fault tolerant applications. INPUT FAIL-SAFE The receiver inputs of the DS90CP22 do not have internal failsafe biasing. For point-to-point and multidrop applications with a single source, fail-safe biasing may not be required. When the driver is off, the link is in-active. If fail-safe biasing is required, this can be accomplished with external high value resistors. The IN+ should be pull to Vcc with 10k and the IN - should be pull to Gnd with 10k. This provides a slight positive differential bias, and sets a known HIGH state on the link with a minimum amount of distortion. UNUSED LVDS INPUTS Unused LVDS Receiver inputs should be tied off to prevent the high-speed sensitive input stage from picking up noise signals. The open input to IN+ should be pull to Vcc with 10k and the open input to IN- should be pull to Gnd with 10k. COMPATIBILITY WITH LVDS STANDARD The DS90CP22 is compatible with LVDS and Bus LVDS Interface devices. It is enhanced over standard LVDS drivers in that it is able to driver lower impedance loads with standard LVDS levels. Standard LVDS drivers provide 330mV differential output with a 100 load. The DS90CP22 provides 365mV with a 75 load or 400mV with 100 loads. This extra drive capability is useful in certain multidrop applications. In backplane multidrop configurations, with closely spaced loads, the effective differential impedance of the line is reduced. If the mainline has been designed for 100 differential impedance, the loading effects may reduce this to the 70 range depending upon spacing and capacitance load. Terminating the line with a 75 load is a better match than with 100 and reflections are reduced. UNUSED CONTROL INPUTS The SEL and EN control input pins have internal pull down devices. Unused pins may be tied off or left as no-connect (if a LOW state is desired). EXPANDING THE NUMBER OF OUTPUT PORTS To expand the number of output ports, more than one DS90CP22 can be used. Total propagation delay through the devices should be considered to determine the maximum expansion. For example, if 2 X 4 is desired, than three of the DS90CP22 are required. A minimum of two device propagation delays (2 x 1.3ns = 2.6ns (typ)) can be achieved. For a 2 X 8, a total of 7 devices must be used with propagation delay of 3 x 1.3ns = 3.9ns (typ). The power consumption will increase proportional to the number of devices used. Block Diagram www.national.com 6 DS90CP22 10105301 Function Table SEL0 SEL1 OUT0 OUT1 Mode 0 0 IN0 IN0 1:2 splitter 0 1 IN0 IN1 repeater 1 0 IN1 IN0 switch 1 1 IN1 IN1 1:2 splitter Note: 0 = low, 1 = high EN0 = EN1 = 1 for enable Typical Performance Characteristics Diff. Output Voltage (VOD) vs. Resistive Load (RT) 10105311 7 www.national.com DS90CP22 Peak-to-Peak Output Jitter at VCM = +0.4V vs. VID 10105312 Peak-to-Peak Output Jitter at VCM = +1.2V vs. VID 10105313 Peak-to-Peak Output Jitter at VCM = +1.6V vs. VID 10105314 www.national.com 8 DS90CP22 Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS90CP22M-8 See NS Package Number M16A 16-Lead (4.4mm Wide) Molded Thin Shrink Small Outline Package, JEDEC Order Number DS90CP22MT Order Number DS90CP22MTX (Tape and Reel) See NS Package Number MTC16 9 www.national.com DS90CP22 800 Mbps 2x2 LVDS Crosspoint Switch Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated