DATASHEET Common-mode Chokes RN series Current-compensated Chokes Rated currents from 0.3 to 10 A Approvals DC to 400 Hz frequency 100 kHz to 3 MHz common-mode resonance frequency Dual-choke configurations Multiple PCB-mounting options Performance indicators RN chokes are attenuating common-mode or asymmetric (P/N -> E) interference signals, by being connected in series with the phase and neutral lines of an AC powerline input. Symmetrical components of the noise are also attenuated by the leakage inductance (stray inductance) of the windings. These chokes are typically used in conjunction with suppression capacitors. Features and benefits High saturation resistance and excellent thermal behavior Through hole pin connections Dual-choke configuration Technical specifications Small compact design Multiple housing options Operating voltage Operating frequency Rated currents Rated inductance Stray inductance 300 VAC Custom-specific versions are available on request DC to 400 Hz Higher temperature versions Inductance reduction (DC bias with IN) High potential test voltage winding-towinding @ 25C winding-to-housing @ 25C MTBF @ 40C/230 V (Mil-HB-217F) Surge current @ 10 msec Less than 10% (25C) Temperature range (operation and storage) -40C to 100C (40/100/56) acc. IEC 60068-1 Flammability corresponding to Potting compound UL 94V-0 Housing UL 94V-0 Ringcore coating UL 94V-0 Design corresponding to UL 1283, IEC/EN 60938-1 0.3 to 10 A @ rated ambient temperature 0.4 to 100 mH Fully potted design usable for ruggedized applications Typically 1% of LN 1500 VAC, 60 sec, guaranteed 1500 VAC, 2 sec, factory test 4000 VAC, 60 sec, guaranteed >5,000,000 hours 20 x IN @ 25C Typical applications Switch-mode power applications Suppressing common-mode interference levels EMI input filters For suppression-equipment with no earth connection Phase-angle control circuits in combination with saturating chokes Typical electrical schematic 2 EMC/EMI Products Schaffner Group Datasheets 28 Jan 2020 Choke selection table Current @ ambient (lN) A B H Weight temperature (LN) (RDC) [A] [C] [mH] [mOhm] RN 102-0.3-02-22M 0.3 40 [mm] [mm] [mm] (g) 22.0 1300 10.0 10.0 9.0 RN 102-0.3-02-12M 0.3 4 buy 40 12.0 1100 10.0 10.0 9.0 3 buy RN 102-0.6-02-4M4 RN 102-1-02-3M0 0.6 40 4.4 380 10.0 10.0 9.0 3 1.0 40 3.0 210 10.0 10.0 9.0 3 RN 102-1.5-02-1M6 1.5 40 1.6 94 10.0 10.0 9.0 3 RN 102-2-02-1M1 2.0 40 1.1 70 10.0 10.0 9.0 3 RN 112-0.4-02-39M 0.4 40 39.0 1500 15.0 10.0 12.6 6 RN 112-0.4-02-27M 0.4 40 27.0 1400 15.0 10.0 12.6 6 RN 112-0.5-02-27M 0.5 40 27.0 1200 15.0 10.0 12.6 6 RN 112-0.5-02-18M 0.5 40 18.0 1100 15.0 10.0 12.6 6 RN 112-0.5-02-15M 0.5 40 15.0 700 15.0 10.0 12.6 6 RN 112-0.6-02-15M 0.6 40 15.0 490 15.0 10.0 12.6 6 RN 112-0.8-02-10M 0.8 40 10.0 380 15.0 10.0 12.6 6 RN 112-1.2-02-6M8 1.2 40 6.8 250 15.0 10.0 12.6 6 RN 112-1.5-02-3M3 1.5 40 3.3 102 15.0 10.0 12.6 6 RN 112-2-02-1M8 2.0 40 1.8 74 15.0 10.0 12.6 6 RN 112-2-02-1M0 2.0 40 1.0 70 15.0 10.0 12.6 6 RN 112-2.6-02-0M4 2.6 40 0.4 40 15.0 10.0 12.6 6 RN 112-3.6-02-0M4 3.6 40 0.4 27 15.0 10.0 12.6 6 RN 112-4-02-0M7 4.0 40 0.7 24 15.0 10.0 12.6 6 RN 114-0.3-02-47M 0.3 40 47.0 1700 20.1 12.5 13.2 10 RN 114-0.5-02-39M 0.5 40 39.0 830 20.1 12.5 13.2 11 RN 114-0.8-02-27M 0.8 40 27.0 500 20.1 12.5 13.2 11 RN 114-1-02-15M 1.0 40 15.0 370 20.1 12.5 13.2 10 RN 114-1.2-02-10M 1.2 40 10.0 195 20.1 12.5 13.2 10 RN 114-1.5-02-6M8 1.5 40 6.8 123 20.1 12.5 13.2 11 RN 114-2-02-4M2 2.0 40 4.2 100 20.1 12.5 13.2 11 RN 114-2.5-02-3M3 2.5 40 3.3 72 20.1 12.5 13.2 11 RN 114-3-02-2M0 3.0 40 2.0 52 20.1 12.5 13.2 10 RN 114-4-02-1M5 4.0 40 1.5 34 20.1 12.5 13.2 11 RN 116-0.5-02-47M 0.5 60 47.0 960 20.1 12.5 13.2 11 RN 116-0.5-02-39M 0.5 60 39.0 920 20.1 12.5 13.2 11 RN 116-0.5-02-27M 0.5 60 27.0 790 20.1 12.5 13.2 11 RN 116-0.8-02-27M 0.8 60 27.0 370 20.1 12.5 13.2 13 RN 116-1-02-15M 1.0 60 15.0 260 20.1 12.5 13.2 12 RN 116-1-02-10M 1.0 60 10.0 210 20.1 12.5 13.2 11 RN 116-1.3-02-6M8 1.3 60 6.8 140 20.1 12.5 13.2 12 RN 116-1.5-02-10M 1.5 60 10.0 148 20.1 12.5 13.2 12 RN 116-1.7-02-4M0 1.7 60 4.0 87 20.1 12.5 13.2 12 RN 116-2-02-3M3 2.0 60 3.3 70 20.1 12.5 13.2 12 RN 116-2-02-2M2 2.0 60 2.2 66 20.1 12.5 13.2 11 RN 122-0.5-02-56M 0.5 40 56.0 1800 25.0 15.0 16.5 20 RN 122-0.6-02-47M 0.6 40 47.0 1300 25.0 15.0 16.5 20 RN 122-0.8-02-39M 0.8 40 39.0 1000 25.0 15.0 16.5 20 RN 122-1-02-18M 1.0 40 18.0 630 25.0 15.0 16.5 19 RN 122-1-02-10M 1.0 40 10.0 560 25.0 15.0 16.5 19 RN 122-1.5-02-10M 1.5 40 10.0 250 25.0 15.0 16.5 20 RN 122-2-02-6M8 2.0 40 6.8 156 25.0 15.0 16.5 20 RN 122-2-02-5M0 2.0 40 5.0 140 25.0 15.0 16.5 21 RN 122-2.5-02-5M6 2.5 40 5.6 110 25.0 15.0 16.5 20 RN 122-3-02-4M5 3.0 40 4.5 80 25.0 15.0 16.5 21 RN 122-4-02-3M3 4.0 40 3.3 46 25.0 15.0 16.5 22 RN 122-4-02-1M8 4.0 40 1.8 42 25.0 15.0 16.5 22 Choke Inductance Resistance 3 EMC/EMI Products Choke Schaffner Group Current @ ambient (lN) temperature (LN) (RDC) [A] [C] [mH] RN 142-0.5-02-82M 0.5 40 RN 142-1-02-33M 1.0 RN 142-1.4-02-27M RN 142-2-02-6M8 Datasheets 28 Jan 2020 A B H Weight [mOhm] [mm] [mm] [mm] (g) 82.0 2700 30.0 20.0 19.7 36 40 33.0 810 30.0 20.0 19.7 37 1.4 40 27.0 500 30.0 20.0 19.7 40 2.0 40 6.8 192 30.0 20.0 19.7 36 RN 142-4-02-3M3 4.0 40 3.3 67 30.0 20.0 19.7 38 RN 142-6-02-1M8 6.0 40 1.8 20 30.0 20.0 19.7 40 RN 143-0.5-02-100M 0.5 40 100.0 2900 30.0 20.0 19.7 36 RN 143-1-02-47M 1.0 40 47.0 890 30.0 20.0 19.7 38 RN 143-2-02-10M 2.0 40 10.0 240 30.0 20.0 19.7 42 RN 143-4-02-3M9 4.0 40 3.9 59 30.0 20.0 19.7 39 RN 143-6-02-1M8 6.0 40 1.8 20 30.0 20.0 19.7 42 RN 152-1-02-68M 1.0 40 68.0 1300 40.0 15.0 25.0 75 RN 152-2-02-18M 2.0 40 18.0 350 40.0 15.0 25.0 64 RN 152-4-02-6M8 4.0 40 6.8 87 40.0 15.0 25.0 74 RN 152-6-02-3M9 6.0 40 3.9 42 40.0 15.0 25.0 68 RN 152-8-02-2M7 8.0 40 2.7 22 40.0 15.0 25.0 73 RN 152-10-02-1M8 10.0 40 1.8 14 40.0 15.0 25.0 73 RN 202-0.3-02-22M 0.3 40 22.0 1300 5.1 15.2 13.5 4 RN 202-0.3-02-12M 0.3 40 12.0 1100 5.1 15.2 13.5 4 RN 202-0.6-02-4M4 0.6 40 4.4 380 5.1 15.2 13.5 4 RN 202-1-02-3M0 1.0 40 3.0 210 5.1 15.2 13.5 4 RN 202-1.5-02-1M6 1.5 40 1.6 94 5.1 15.2 13.5 4 RN 202-2-02-1M1 2.0 40 1.1 70 5.1 15.2 13.5 4 RN 204-0.3-02-22M 0.3 40 22.0 1300 7.6 10.0 14.3 3 RN 204-0.3-02-12M 0.3 40 12.0 960 7.6 10.0 14.3 3 RN 204-0.6-02-4M4 0.6 40 4.4 350 7.6 10.0 14.3 3 RN 204-1-02-3M0 1.0 40 3.0 192 7.6 10.0 14.3 3 RN 204-1.5-02-1M6 1.5 40 1.6 96 7.6 10.0 14.3 3 RN 204-2-02-1M1 2.0 40 1.1 57 7.6 10.0 14.3 3 RN 212-0.4-02-39M 0.4 40 39.0 1500 10.0 15.0 20.0 8 RN 212-0.4-02-27M 0.4 40 27.0 1400 10.0 15.0 20.0 8 RN 212-0.5-02-27M 0.5 40 27.0 1200 10.0 15.0 20.0 8 RN 212-0.5-02-18M 0.5 40 18.0 1100 10.0 15.0 20.0 8 RN 212-0.5-02-15M 0.5 40 15.0 700 10.0 15.0 20.0 8 RN 212-0.6-02-15M 0.6 40 15.0 490 10.0 15.0 20.0 8 RN 212-0.8-02-10M 0.8 40 10.0 380 10.0 15.0 20.0 8 RN 212-1.2-02-6M8 1.2 40 6.8 250 10.0 15.0 20.0 8 RN 212-1.5-02-3M3 1.5 40 3.3 102 10.0 15.0 20.0 8 RN 212-2-02-1M8 2.0 40 1.8 74 10.0 15.0 20.0 8 RN 212-2-02-1M0 2.0 40 1.0 70 10.0 15.0 20.0 8 RN 212-2.6-02-0M4 2.6 40 0.4 40 10.0 15.0 20.0 8 RN 212-3.6-02-0M4 3.6 40 0.4 27 10.0 15.0 20.0 8 RN 212-4-02-0M7 4.0 40 0.7 24 10.0 15.0 20.0 8 RN 214-0.3-02-47M 0.3 40 47.0 1700 12.5 10.0 25.0 14 RN 214-0.5-02-56M 0.5 40 56.0 1700 12.5 10.0 25.0 15 RN 214-0.5-02-39M 0.5 40 39.0 830 12.5 10.0 25.0 14 RN 214-0.8-02-27M 0.8 40 27.0 500 12.5 10.0 25.0 15 RN 214-1-02-15M 1.0 40 15.0 370 12.5 10.0 25.0 14 RN 214-1.2-02-10M 1.2 40 10.0 195 12.5 10.0 25.0 15 RN 214-1.5-02-6M8 1.5 40 6.8 123 12.5 10.0 25.0 15 RN 214-2-02-4M2 2.0 40 4.2 100 12.5 10.0 25.0 14 Inductance Resistance 4 EMC/EMI Products Schaffner Group Current @ ambient (lN) temperature (LN) (RDC) [A] [C] [mH] RN 214-2-02-2M2 2.0 40 RN 214-2.5-02-3M3 2.5 RN 214-3-02-2M0 Datasheets 28 Jan 2020 A B H Weight [mOhm] [mm] [mm] [mm] (g) 2.2 67 12.5 10.0 25.0 14 40 3.3 72 12.5 10.0 25.0 15 3.0 40 2.0 52 12.5 10.0 25.0 14 RN 214-4-02-1M5 4.0 40 1.5 34 12.5 10.0 25.0 15 RN 216-0.5-02-47M 0.5 60 47.0 960 12.5 10.0 25.0 15 RN 216-0.5-02-39M 0.5 60 39.0 920 12.5 10.0 25.0 15 RN 216-0.5-02-27M 0.5 60 27.0 790 12.5 10.0 25.0 15 RN 216-0.8-02-27M 0.8 60 27.0 370 12.5 10.0 25.0 16 RN 216-1-02-15M 1.0 60 15.0 260 12.5 10.0 25.0 16 RN 216-1-02-10M 1.0 60 10.0 210 12.5 10.0 25.0 15 RN 216-1.3-02-6M8 1.3 60 6.8 140 12.5 10.0 25.0 16 RN 216-1.5-02-10M 1.5 60 10.0 148 12.5 10.0 25.0 16 RN 216-1.7-02-4M0 1.7 60 4.0 87 12.5 10.0 25.0 16 RN 216-2-02-3M3 2.0 60 3.3 70 12.5 10.0 25.0 16 RN 216-2-02-2M2 2.0 60 2.2 66 12.5 10.0 25.0 15 RN 218-0.4-02-100M 0.4 40 100 2800 10.0 12.5 20.0 8 RN 218-0.6-02-47M 0.6 40 47.0 1200 10.0 12.5 20.0 8 RN 218-0.7-02-39M 0.7 40 39.0 1150 10.0 12.5 20.0 8 RN 218-0.9-02-27M 0.9 40 27.0 620 10.0 12.5 20.0 8 RN 218-1-02-22M 1.0 40 22.0 520 10.0 12.5 20.0 8 RN 218-1.1-02-15M 1.1 40 15.0 420 10.0 12.5 20.0 8 RN 218-1.4-02-10M 1.4 40 10.0 330 10.0 12.5 20.0 8 RN 218-1.7-02-6M8 1.7 40 6.8 180 10.0 12.5 20.0 8 RN 218-2.2-02-3M3 2.2 40 3.3 100 10.0 12.5 20.0 8 RN 222-0.5-02-56M 0.5 40 56.0 1800 15.0 12.5 29.3 27 RN 222-0.6-02-47M 0.6 40 47.0 1300 15.0 12.5 29.3 26 RN 222-0.8-02-39M 0.8 40 39.0 1000 15.0 12.5 29.3 27 RN 222-1-02-33M 1.0 40 33.0 1300 15.0 12.5 29.3 29 RN 222-1-02-18M 1.0 40 18.0 630 15.0 12.5 29.3 26 RN 222-1.5-02-10M 1.5 40 10.0 250 15.0 12.5 29.3 26 RN 222-2-02-6M8 2.0 40 6.8 156 15.0 12.5 29.3 28 RN 222-2.5-02-5M6 2.5 40 5.6 110 15.0 12.5 29.3 27 RN 222-3-02-4M5 3.0 40 4.5 80 15.0 12.5 29.3 28 RN 222-4-02-3M3 4.0 40 3.3 46 15.0 12.5 29.3 28 RN 232-0.6-02-47M 0.6 40 47.0 1300 15.0 12.5 34.3 37 RN 232-1-02-18M 1.0 40 18.0 390 15.0 12.5 34.3 38 RN 232-1.6-02-10M 1.6 40 10.0 170 15.0 12.5 34.3 38 RN 232-2.5-02-5M6 2.5 40 5.6 86 15.0 12.5 34.3 38 RN 232-4-02-3M3 4.0 40 3.3 54 15.0 12.5 34.3 38 RN 242-0.5-02-82M 0.5 40 82.0 2700 15.0 12.5 34.3 37 RN 242-1-02-33M 1.0 40 33.0 810 15.0 12.5 34.3 38 RN 242-1.4-02-27M 1.4 40 27.0 500 15.0 12.5 34.3 38 RN 242-2-02-6M8 2.0 40 6.8 192 15.0 12.5 34.3 37 RN 242-4-02-3M3 4.0 40 3.3 67 15.0 12.5 34.3 38 RN 242-6-02-1M8 6.0 40 1.8 20 15.0 12.5 34.3 41 Choke Inductance Resistance Test conditions: Measuring frequency: 10 kHz; 50 mV; Inductance tolerance: +50%, -30%; Resistance tolerance: 15% @ 25C; Electrical characteristics @ 25C: 2C; Stray Inductance measurement between pin 1 and 2 (pin 3 and 4 shorted) For mechanical tolerances refer to mechanical data section. 5 EMC/EMI Products Product selector Thermal Derating If higher ambient temperatures than the specified apply, the nominal current needs to be reduced according to the graph below. Schaffner Group Datasheets 28 Jan 2020 6 EMC/EMI Products Schaffner Group Typical attenuation/resonance frequency characteristics Per CISPR 17; 50 /50 asym X can be exchanged with either 1 or 2 for different housing configuration, attenuation is similar RN 102, RN 202 RN 204 RN 112, RN 212 (<1 A) RN 112, RN 212 (>1 A) RN 114, RN 214 RN 116, RN 216 Datasheets 28 Jan 2020 7 EMC/EMI Products Schaffner Group RN 218 RN 122, RN 222 RN 232 RN 142, RN 242 RN 143 RN 152 Datasheets 28 Jan 2020 EMC/EMI Products Schaffner Group Datasheets 28 Jan 2020 Mechanical data RN 112, RN 114, RN 116, RN 122, RN 142/3 3 4 1 2 B 4 3 2 1 P 1 W 3 P B 4 2 A H H 3 4 1 2 P A W H W A RN 152 B RN 102 L 1 P RN 204 A 3 2 1 4 3 2 1 2 L P L 4 3 2 1 3 4 P P B W B 4 H B 4 A H P P H W A RN 212, RN 218 1 2 L P RN 214, RN 216, RN 222, RN 232, RN 242 A 3 H 4 3 2 1 W 4 P 1 2 L P Pin material: Steel (base), Cu (under plating), Sn (final plating 6m) Dimensions A B H L W P OP (0.6 mm) (0.6 mm) (0.3 mm) (0.3 mm) (0.3 mm) (0.5 mm) (0.1 mm) RN 102 10.0 mm 10.0 mm 9.0 mm 14.0 mm 14.0 mm 4.0 mm 0.6 mm RN 112 15.0 mm 10.0 mm 12.6 mm 17.7 mm 17.1 mm 4.0 mm 0.8 mm RN 114 20.1 mm 12.5 mm 13.2 mm 22.5 mm 21.5 mm 4.0 mm 0.8 mm RN 116 20.1 mm 12.5 mm 13.2 mm 22.5 mm 21.5 mm 4.0 mm 0.8 mm RN 122 25.0 mm 15.0 mm 16.5 mm 28.0 mm 27.0 mm 4.0 mm 0.8 mm RN 142 30.0 mm 20.0 mm 19.7 mm 33.1 mm 32.5 mm 4.3 mm 0.8 mm RN 143 30.0 mm 20.0 mm 19.7 mm 33.1 mm 32.5 mm 4.3 mm 0.8 mm RN 152 40.0 mm 15.0 mm 25.0 mm 43.0 mm 41.8 mm 4.5 mm 1.2 mm RN 202 5.1 mm 15.2 mm 13.5 mm 8.8 mm 18.2 mm 4.5 mm 0.8 mm RN 204 7.6 mm 10.0 mm 14.3 mm 9.0 mm 14.0 mm 4.0 mm 0.5 mm RN 212 10.0 mm 15.0 mm 20.0 mm 12.5 mm 18.0 mm 4.0 mm 0.8 mm RN 214 12.5 mm 10.0 mm 25.0 mm 15.5 mm 23.0 mm 4.0 mm 0.8 mm RN 216 12.5 mm 10.0 mm 25.0 mm 15.5 mm 23.0 mm 4.0 mm 0.8 mm RN 218 10.0 mm 12.5 mm 20.0 mm 12.5 mm 18.0 mm 4.0 mm 0.8 mm RN 222 15.0 mm 12.5 mm 29.3 mm 18.0 mm 31.0 mm 4.0 mm 0.8 mm RN 232 15.0 mm 12.5 mm 34.3 mm 18.0 mm 31.0 mm 4.2 mm 0.8 mm RN 242 15.0 mm 12.5 mm 34.3 mm 18.0 mm 31.0 mm 4.2 mm 0.8 mm Please visit www.schaffner.com to find more details on filter connections. 4 3 2 1 W RN 202 1 3 2 P L 3 4 P L B 8 9 EMC/EMI Products Schaffner Group Datasheets 28 Jan 2020 Headquarters, global innovation and development Sales and application centers Switzerland Schaffner Group Industrie Nord Nordstrasse 11e 4542 Luterbach T +41 32 681 66 26 info@schaffner.com China Schaffner EMC Ltd. Shanghai T20-3 C, No 565 Chuangye Road, Pudong district 201201 Shanghai T +86 21 3813 9500 cschina@schaffner.com www.schaffner.com.cn Spain Schaffner EMC Espana Calle Calendula 93, Miniparc III, Edificio E El Soto de Moraleja, Alcobendas 28109 Madrid T +34 917 912 900 F +34 917 912 901 spainsales@schaffner.com Finland Schaffner Oy Sauvonrinne 19 H 08500 Lohja T +358 10 567 2855 finlandsales@schaffner.com Sweden Schaffner EMC AB Ostermalmstorg 1 114 42 Stockholm T +46 8 5050 2425 swedensales@schaffner.com www.schaffner.com France Schaffner EMC S.A.S. 16-20 Rue Louis Rameau 95875 Bezons T +33 1 34 34 30 60 F +33 1 39 47 02 28 francesales@schaffner.com Germany Schaffner Deutschland GmbH Schoemperlenstrasse 12B 76185 Karlsruhe T +49 721 56910 F +49 721 569110 germanysales@schaffner.com India Schaffner India Pvt. Ltd REGUS WORLD TRADE CENTRE WTC, 22nd Floor Unit No 2238, Brigade Gateway Campus, 26/1, Dr. Rajkumar Road Malleshwaram (W) 560055 Bangalore T +91 80 67935355 indiasales@schaffner.com To find your local partner within Schaffner`s global network: www.schaffner.com (c) 2018 Schaffner Group The content of this document has been carefully checked and understood. However, neither Schaffner nor its subsidiaries assume any liability whatsoever for any errors or inaccuracies of this document and the consequences thereof. Published specifications are subject to change without notice. Product suitability for any area of application must ultimately be determined by the customer. In all cases, products must never be operated outside their published specifications. Schaffner does not guarantee the availability of all published products. This disclaimer shall be governed by substantive Swiss law and resulting disputes shall be settled by the courts at the place of business of Schaffner Holding AG. Latest publications and a complete disclaimer can be downloaded from the Schaffner website. All trademarks recognized. Italy Schaffner EMC S.r.l. Via Ticino, 30 20900 Monza (MB) T +39 039 21 41 070 italysales@schaffner.com Japan Schaffner EMC K.K. Taiju-Seimei Sangenjaya Bldg. 1-32-12, Kamiuma, Setagaya-ku 154-0011 Tokyo T +81 3 5712 3650 F +81 3 5712 3651 japansales@schaffner.com www.schaffner.jp Singapore Schaffner EMC Pte Ltd. #05-09, Kg Ubi Ind. Estate 408705 Singapore T +65 6377 3283 F +65 6377 3281 singaporesales@schaffner.com Switzerland Schaffner EMV AG Industrie Nord Nordstrasse 11e 4542 Luterbach T +41 32 681 66 26 switzerlandsales@schaffner.com Taiwan R.O.C. Schaffner EMV Ltd. 20 Floor-2, No 97, Section 1, XinTai 5th Road 22175 XiZhi District New Taipei City 22175 T +886 2 2697 5500 F +886 2 2697 5533 taiwansales@schaffner.com www.schaffner.com.tw Thailand Schaffner EMC Co. Ltd. Northern Region Industrial Estate 67 Moo 4 Tambon Ban Klang Amphur Muangg P.O. Box 14 51000 Lamphun T +66 53 58 11 04 F +66 53 58 10 19 thailandsales@schaffner.com United Kingdom Schaffner Ltd. 5 Ashville Way, Molly Millars Lane Wokingham RG41 2PL Berkshire T +44 118 9770070 F +44 118 9792969 uksales@schaffner.com USA Schaffner EMC Inc. 52 Mayfield Avenue Edison, New Jersey T +1 732 225 9533 F +1 732 225 4789 usasales@schaffner.com www.schaffnerusa.com Schaffner North America 6722 Thirlane Road 24019 Roanoke, Virginia T +1 276 228 7943 F +1 276 228 7953 Schaffner North America 823 Fairview Road 24382 Wytheville, Virginia T +1 276 228 7943 F +1 276 228 7258