CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
18-Mbit QDR® II SRAM
Four-Word Burst Architecture
Cypress Semiconductor Corporation 198 Champion Court San Jose, CA 95134-1709 408-943-2600
Document Number: 001-58904 Rev. *C Revised March 1, 2011
18-Mbit QDR® II SRAM Four-Word Burst Architectu re
Features
Separate independent read and write data ports
Supports concurrent transactions
333-MHz clock for high bandwidth
Four-word burst for reducing address bus frequency
Double data rate (DDR) interfaces on both read and write ports
(data transferred at 666 MHz) at 333 MHz
Two input clocks (K and K) for precise DDR timing
SRAM uses rising edges only
Two Input Clocks for Output Data (C and C) to minimize Clock
skew and flight time mismatches
Echo clocks (CQ and CQ) simplify data capture in high speed
systems
Single multiplexed address input bus latches address inputs
for read and write ports
Separate port selects for depth expansion
Synchronous internally self-timed writes
QDR® II operates with 1.5 cycle read latency when DOFF is
asserted HIGH
Operates similar to QDR I device with 1 cycle read latency when
DOFF is asserted LOW
Available in ×8, ×9, ×18, and ×36 configurations
Full data coherency, providing most current data
Core VDD = 1.8 V (±0.1 V); I/O VDDQ = 1.4 V to VDD
Supports both 1.5 V and 1.8 V I/O supply
Available in 165-ball FBGA package (13 × 15 × 1.4 mm)
Offered in both Pb-free and non Pb-free packages
Variable drive HSTL output buffers
JTAG 1149.1 compatible test access port
PLL for accurate data placement
Configurations
CY7C1311KV18 – 2 M × 8
CY7C1911KV18 – 2 M × 9
CY7C1313KV18 – 1 M × 18
CY7C1315KV18 – 512 K × 36
Functional Description
The CY7C1311KV18, CY7C1911KV18, CY7C1313KV18, and
CY7C1315KV18 are 1.8 V Synchronous Pipelined SRAMs,
equipped with QDR II architecture. QDR II architecture consists
of two separate ports: the read port and the write port to access
the memory array. The read port has dedicated data outputs to
support read operations and the write port has dedicated data
inputs to support write operations. QDR II architecture has
separate data inputs and data outputs to completely eliminate
the need to ‘turnaround’ the data bus that exists with common
I/O devices. Each port can be accessed through a common
address bus. Addresses for read and write addresses are
latched on alternate rising edges of the input (K) clock. Accesses
to the QDR II read and write ports are independent of one
another. To maximize data throughput, both read and write ports
are equipped with DDR interfaces. Each address location is
associated with four 8-bit words (CY7C1311KV18), 9-bit words
(CY7C1911KV18), 18-bit words (CY7C1313KV18), or 36-bit
words (CY7C1315KV18) that burst sequentially into or out of the
device. Because data can be transferred into and out of the
device on every rising edge of both input clocks (K and K and C
and C), memory bandwidth is maximized while simplifying
system design by eliminating bus ‘turnarounds’.
Depth expansion is accomplished with port selects, which
enables each port to operate independently.
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
Selection Guide
Description 333 MHz 300 MHz 250 MHz 200 MHz 167 MHz Unit
Maximum operating frequency 333 300 250 200 167 MHz
Maximum operating current × 8 520 490 430 380 340 mA
× 9 520 490 430 380 340
× 18 530 500 440 390 350
× 36 730 670 590 500 450
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 2 of 33
Logic Block Diagram (CY7C1311KV18)
Logic Block Diagram (CY7C1911KV18)
512 K x 8 Array
CLK
A(18:0)
Gen.
K
K
Control
Logic
Address
Register
D[7:0]
Read Add. Decode
Read Data Reg.
RPS
WPS
Control
Logic
Address
Register
Reg.
Reg.
Reg.
16
19
32
8
NWS[1:0]
VREF
Write Add. Decode
Write
Reg
16
A(18:0)
19
8
CQ
CQ
DOFF
Q[7:0]
8
8
8
Write
Reg
Write
Reg
Write
Reg
C
C
512 K x 8 Array
512 K x 8 Array
512 K x 8 Array
8
CLK
A(18:0)
Gen.
K
K
Control
Logic
Address
Register
D[8:0]
Read Add. Decode
Read Data Reg.
RPS
WPS
Control
Logic
Address
Register
Reg.
Reg.
Reg.
18
19
36
9
BWS[0]
VREF
Write Add. Decode
Write
Reg
18
A(18:0)
19
9
CQ
CQ
DOFF
Q[8:0]
9
9
9
Write
Reg
Write
Reg
Write
Reg
C
C
512 K x 9 Array
512 K x 9 Array
512 K x 9 Array
512 K x 9 Array
9
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 3 of 33
Logic Block Diagram (CY7C1313KV18)
Logic Block Diagram (CY7C1315KV18)
CLK
A(17:0)
Gen.
K
K
Control
Logic
Address
Register
D[17:0]
Read Add. Decode
Read Data Reg.
RPS
WPS
Control
Logic
Address
Register
Reg.
Reg.
Reg.
36
18
72
18
BWS[1:0]
VREF
Write Add. Decode
Write
Reg
36
A(17:0)
18
18
CQ
CQ
DOFF
Q[17:0]
18
18
18
Write
Reg
Write
Reg
Write
Reg
C
C
256 K x 18 Array
256 K x 18 Array
256 K x 18 Array
256 K x 18 Array
18
128 K x 36 Array
CLK
A(16:0)
Gen.
K
K
Control
Logic
Address
Register
D[35:0]
Read Add. Decode
Read Data Reg.
RPS
WPS
Control
Logic
Address
Register
Reg.
Reg.
Reg.
72
17
144
36
BWS[3:0]
VREF
Write Add. Decode
Write
Reg
72
A(16:0)
17
128 K x 36 Array
128 K x 36 Array
128 K x 36 Array
36
CQ
CQ
DOFF
Q[35:0]
36
36
36
Write
Reg
Write
Reg
Write
Reg
C
C
36
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 4 of 33
Contents
Pin Configuration ............................................................. 5
165-ball FBGA (13 × 15 × 1.4 mm) Pinout .................. 5
Pin Definitions .................................................................. 7
Functional Overview ........................................................ 9
Read Operations .........................................................9
Write Operations .........................................................9
Byte Write Operations .................................................9
Single Clock Mode ...................................................... 9
Concurrent Transactions ........................................... 10
Depth Expansion ....................................................... 10
Programmable Impedance ........................................ 10
Echo Clocks .............................................................. 10
PLL ............................................................................10
Application Example ...................................................... 11
Truth Table ......................................................................11
Write Cycle Descriptions ............................................... 12
Write Cycle Descriptions ............................................... 12
Write Cycle Descriptions ............................................... 13
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 14
Disabling the JTAG Feature ......................................14
Test Access Port—Test Clock ................................... 14
Test Mode Select (TMS) ...........................................14
Test Data-In (TDI) ..................................................... 14
Test Data-Out (TDO) ................................................. 14
Performing a TAP Reset ........................................... 14
TAP Registers ...........................................................14
TAP Instruction Set ...................................................14
TAP Controller State Diagram .......................................16
TAP Controller Block Diagram ......................................17
TAP Electrical Characteristics ......................................17
TAP AC Switching Characteristics ............................... 18
TAP Timing and Test Conditions .................................. 18
Identification Register Definitions ................................ 19
Scan Register Sizes ....................................................... 19
Instruction Codes ........................................................... 19
Boundary Scan Order .................................................... 20
Power Up Sequence in QDR II SRAM ........................... 21
Power Up Sequence ................................................. 21
PLL Constraints ......................................................... 21
Maximum Ratings ........................................................... 22
Operating Range ............................................................. 22
Neutron Soft Error Immunity ......................................... 22
Electrical Characteristics ............................................... 22
DC Electrical Characteristics ..................................... 22
AC Electrical Characteristics ..................................... 24
Capacitance .................................................................... 25
Thermal Resistance ........................................................ 25
Switching Characteristics .............................................. 26
Switching Waveforms .................................................... 28
Ordering Information ...................................................... 29
Ordering Code Definitions ......................................... 29
Package Diagram ............................................................ 30
Acronyms ....................................................................... 31
Document Conventions ................................................. 31
Units of Measure ....................................................... 31
Document History Page ................................................. 32
Sales, Solutions, and Legal Information ...................... 33
Worldwide Sales and Design Support ....................... 33
Products .................................................................... 33
PSoC Solutions ......................................................... 33
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 5 of 33
Pin Configuration
The pin configurations for CY7C1311KV18, CY7C1911KV18, CY7C1313KV18, and CY7C1315KV18 follow.[1]
165-ball FBGA (13 × 15 × 1.4 mm) Pinout
CY7C1311KV18 (2 M × 8)
12345678910 11
ACQ NC/72M A WPS NWS1KNC/144M RPS ANC/36MCQ
BNC NC NC A NC/288M K NWS0ANCNCQ3
CNC NC NC VSS ANCAV
SS NC NC D3
DNC D4 NC VSS VSS VSS VSS VSS NC NC NC
ENC NC Q4 VDDQ VSS VSS VSS VDDQ NC D2 Q2
FNC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC
GNC D5 Q5 VDDQ VDD VSS VDD VDDQ NC NC NC
HDOFF VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ
JNC NC NC VDDQ VDD VSS VDD VDDQ NC Q1 D1
KNC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC
LNC Q6 D6 VDDQ VSS VSS VSS VDDQ NC NC Q0
MNC NC NC VSS VSS VSS VSS VSS NC NC D0
NNC D7 NC VSS AAAV
SS NC NC NC
PNC NC Q7 A A C A A NC NC NC
RTDOTCKAAACAAATMSTDI
CY7C1911KV18 (2 M × 9)
12345678910 11
ACQ NC/72M A WPS NC K NC/144M RPS ANC/36MCQ
BNC NC NC A NC/288M K BWS0ANCNCQ4
CNC NC NC VSS ANCAV
SS NC NC D4
DNC D5 NC VSS VSS VSS VSS VSS NC NC NC
ENC NC Q5 VDDQ VSS VSS VSS VDDQ NC D3 Q3
FNC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC
GNC D6 Q6 VDDQ VDD VSS VDD VDDQ NC NC NC
HDOFF VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ
JNC NC NC VDDQ VDD VSS VDD VDDQ NC Q2 D2
KNC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC
LNC Q7 D7 VDDQ VSS VSS VSS VDDQ NC NC Q1
MNC NC NC VSS VSS VSS VSS VSS NC NC D1
NNC D8 NC VSS AAAV
SS NC NC NC
PNC NC Q8 A A C A A NC D0 Q0
RTDOTCKAAACAAATMSTDI
Note
1. NC/36M, NC/72M, NC/144M, and NC/288M are not connected to the die and can be tied to any voltage level.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 6 of 33
CY7C1313KV18 (1 M × 18)
12345678910 11
ACQ NC/144M NC/36M WPS BWS1KNC/288M RPS ANC/72MCQ
BNC Q9 D9 A NC K BWS0ANCNCQ8
CNC NC D10 VSS ANCAV
SS NC Q7 D8
DNC D11 Q10 VSS VSS VSS VSS VSS NC NC D7
ENC NC Q11 VDDQ VSS VSS VSS VDDQ NC D6 Q6
FNC Q12 D12 VDDQ VDD VSS VDD VDDQ NC NC Q5
GNC D13 Q13 VDDQ VDD VSS VDD VDDQ NC NC D5
HDOFF VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ
JNC NC D14 VDDQ VDD VSS VDD VDDQ NC Q4 D4
KNC NC Q14 VDDQ VDD VSS VDD VDDQ NC D3 Q3
LNC Q15 D15 VDDQ VSS VSS VSS VDDQ NC NC Q2
MNC NC D16 VSS VSS VSS VSS VSS NC Q1 D2
NNC D17 Q16 VSS AAAV
SS NC NC D1
PNC NC Q17 A A C A A NC D0 Q0
RTDOTCKAAACAAATMSTDI
CY7C1315KV18 (512 K × 36)
12345678910 11
ACQ NC/288M NC/72M WPS BWS2KBWS1RPS NC/36M NC/144M CQ
BQ27 Q18 D18 A BWS3KBWS
0AD17Q17Q8
CD27 Q28 D19 VSS ANCAV
SS D16 Q7 D8
DD28 D20 Q19 VSS VSS VSS VSS VSS Q16 D15 D7
EQ29 D29 Q20 VDDQ VSS VSS VSS VDDQ Q15 D6 Q6
FQ30 Q21 D21 VDDQ VDD VSS VDD VDDQ D14 Q14 Q5
GD30 D22 Q22 VDDQ VDD VSS VDD VDDQ Q13 D13 D5
HDOFF VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ
JD31 Q31 D23 VDDQ VDD VSS VDD VDDQ D12 Q4 D4
KQ32 D32 Q23 VDDQ VDD VSS VDD VDDQ Q12 D3 Q3
LQ33 Q24 D24 VDDQ VSS VSS VSS VDDQ D11 Q11 Q2
MD33 Q34 D25 VSS VSS VSS VSS VSS D10 Q1 D2
ND34 D26 Q25 VSS AAAV
SS Q10 D9 D1
PQ35 D35 Q26 A A C A A Q9 D0 Q0
RTDOTCKAAACAAATMSTDI
Pin Configuration (continued)
The pin configurations for CY7C1311KV18, CY7C1911KV18, CY7C1313KV18, and CY7C1315KV18 follow.[1]
165-ball FBGA (13 × 15 × 1.4 mm) Pinout
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 7 of 33
Pin Definitions
Pin Name I/O Pin Description
D[x:0] Input-
synchronous
Data Input Signals. Sampled on the rising edge of K and K clocks when valid write operations are active.
CY7C1311KV18 D[7:0]
CY7C1911KV18 D[8:0]
CY7C1313KV18 D[17:0]
CY7C1315KV18 D[35:0]
WPS Input-
synchronous
Write Port Select Active LOW. Sampled on the rising edge of the K clock. When asserted active, a write
operation is initiated. Deasserting deselects the write port. Deselecting the write port ignores D[x:0].
NWS0,
NWS1,
Input-
synchronous
Nibble Write Select 0, 1 Active LOW (CY7C1311KV18 only). Sampled on the rising edge of the K and
K clocks when write operations are active. Used to select which nibble is written into the device during
the current portion of the write operations. NWS0 controls D[3:0] and NWS1 controls D[7:4].
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select
ignores the corresponding nibble of data and it is not written into the device.
BWS0,
BWS1,
BWS2,
BWS3
Input-
synchronous
Byte Write Select 0, 1, 2, and 3 Active LOW. Sampled on the rising edge of the K and K clocks when
write operations are active. Used to select which byte is written into the device during the current portion
of the write operations. Bytes not written remain unaltered.
CY7C1911KV18 BWS0 controls D[8:0]
CY7C1313KV18 BWS0 controls D[8:0] and BWS1 controls D[17:9].
CY7C1315KV18 BWS0 controls D[8:0], BWS1 controls D[17:9],
BWS2 controls D[26:18] and BWS3 controls D[35:27].
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select
ignores the corresponding byte of data and it is not written into the device.
A Input-
synchronous
Address Inputs. Sampled on the rising edge of the K clock during active read and write operations. These
address inputs are multiplexed for both read and write operations. Internally, the device is organized as
2 M × 8 (4 arrays each of 512 K × 8) for CY7C1311KV18, 2 M × 9 (4 arrays each of 512 K × 9) for
CY7C1911KV18, 1 M × 18 (4 arrays each of 256 K × 18) for CY7C1313KV18 and 512 K × 36 (4 arrays
each of 128 K × 36) for CY7C1315KV18. Therefore, only 19 address inputs are needed to access the
entire memory array of CY7C1311KV18 and CY7C1911KV18, 18 address inputs for CY7C1313KV18 and
17 address inputs for CY7C1315KV18. These inputs are ignored when the appropriate port is deselected.
Q[x:0] Outputs-
synchronous
Data Output Signals. These pins drive out the requested data when the read operation is active. Valid
data is driven out on the rising edge of the C and C clocks during read operations, or K and K when in
single clock mode. On deselecting the read port, Q[x:0] are automatically tristated.
CY7C1311KV18 Q[7:0]
CY7C1911KV18 Q[8:0]
CY7C1313KV18 Q[17:0]
CY7C1315KV18 Q[35:0]
RPS Input-
synchronous
Read Port Select Active LOW. Sampled on the rising edge of positive input clock (K). When active, a
read operation is initiated. Deasserting deselects the read port. When deselected, the pending access is
allowed to complete and the output drivers are automatically tristated following the next rising edge of the
C clock. Each read access consists of a burst of four sequential transfers.
C Input clock Positive Input Clock for Output Data. C is used in conjunction with C to clock out the read data from the
device. C and C can be used together to deskew the flight times of various devices on the board back to
the controller. See Application Example on page 11 for further details.
CInput clock Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from the
device. C and C can be used together to deskew the flight times of various devices on the board back to
the controller. See Application Example on page 11 for further details.
K Input clock Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device and
to drive out data through Q[x:0] when in single clock mode. All accesses are initiated on the rising edge of K.
KInput clock Negative Input Clock Input. K is used to capture synchronous inputs being presented to the device and
to drive out data through Q[x:0] when in single clock mode.
CQ Echo clock CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock for
output data (C) of the QDR II. In the single clock mode, CQ is generated with respect to K. The timings
for the echo clocks are shown in the Switching Characteristics on page 26.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 8 of 33
CQ Echo clock CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock for
output data (C) of the QDR II. In the single clock mode, CQ is generated with respect to K. The timings
for the echo clocks are shown in the Switching Characteristics on page 26.
ZQ Input Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus
impedance. CQ, CQ, and Q[x:0] output impedance are set to 0.2 x RQ, where RQ is a resistor connected
between ZQ and ground. Alternatively, this pin can be connected directly to VDDQ, which enables the
minimum impedance mode. This pin cannot be connected directly to GND or left unconnected.
DOFF Input PLL Turn Off Active LOW. Connecting this pin to ground turns off the PLL inside the device. The timings
in the PLL turned off operation differs from those listed in this data sheet. For normal operation, this pin
is connected to a pull up through a 10 K or less pull up resistor. The device behaves in QDR I mode
when the PLL is turned off. In this mode, the device can be operated at a frequency of up to 167 MHz
with QDR I timing.
TDO Output TDO for JTAG.
TCK Input TCK Pin for JTAG.
TDI Input TDI Pin for JTAG.
TMS Input TMS Pin for JTAG.
NC N/A Not Connected to the Die. Can be tied to any voltage level.
NC/36M N/A Not Connected to the Die. Can be tied to any voltage level.
NC/72M N/A Not Connected to the Die. Can be tied to any voltage level.
NC/144M N/A Not Connected to the Die. Can be tied to any voltage level.
NC/288M N/A Not Connected to the Die. Can be tied to any voltage level.
VREF Input-
reference
Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs, and AC
measurement points.
VDD Power supply Power Supply Inputs to the Core of the Device.
VSS Ground Ground for the Device.
VDDQ Power supply Power Supply Inputs for the Outputs of the Device.
Pin Definitions (continued)
Pin Name I/O Pin Description
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 9 of 33
Functional Overview
The CY7C1311KV18, CY7C1911KV18, CY7C1313KV18,
CY7C1315KV18 are synchronous pipelined Burst SRAMs with a
read port and a write port. The read port is dedicated to read
operations and the write port is dedicated to write operations.
Data flows into the SRAM through the write port and flows out
through the read port. These devices multiplex the address
inputs to minimize the number of address pins required. By
having separate read and write ports, the QDR II completely
eliminates the need to turn around the data bus and avoids any
possible data contention, thereby simplifying system design.
Each access consists of four 8-bit data transfers in the case of
CY7C1311KV18, four 9-bit data transfers in the case of
CY7C1911KV18, four 18-bit data transfers in the case of
CY7C1313KV18, and four 36-bit data transfers in the case of
CY7C1315KV18 in two clock cycles.
This device operates with a read latency of one and half cycles
when DOFF pin is tied HIGH. When DOFF pin is set LOW or
connected to VSS then device behaves in QDR I mode with a
read latency of one clock cycle.
Accesses for both ports are initiated on the positive input clock
(K). All synchronous input timing is referenced from the rising
edge of the input clocks (K and K) and all output timing is
referenced to the output clocks (C and C, or K and K when in
single clock mode).
All synchronous data inputs (D[x:0]) pass through input registers
controlled by the input clocks (K and K). All synchronous data
outputs (Q[x:0]) pass through output registers controlled by the
rising edge of the output clocks (C and C, or K and K when in
single clock mode).
All synchronous control (RPS, WPS, BWS[x:0]) inputs pass
through input registers controlled by the rising edge of the input
clocks (K and K).
CY7C1313KV18 is described in the following sections. The
same basic descriptions apply to CY7C1311KV18,
CY7C1911KV18 and CY7C1315KV18.
Read Operations
The CY7C1313KV18 is organized internally as four arrays of
256 K × 18. Accesses are completed in a burst of four sequential
18-bit data words. Read operations are initiated by asserting
RPS active at the rising edge of the positive input clock (K). The
address presented to the address inputs is stored in the read
address register. Following the next K clock rise, the
corresponding lowest order 18-bit word of data is driven onto the
Q[17:0] using C as the output timing reference. On the
subsequent rising edge of C, the next 18-bit data word is driven
onto the Q[17:0]. This process continues until all four 18-bit data
words are driven out onto Q[17:0]. The requested data is valid
0.45 ns from the rising edge of the output clock (C or C, or K or
K when in single clock mode). To maintain the internal logic, each
read access must be enabled to complete. Each read access
consists of four 18-bit data words and takes two clock cycles to
complete. Therefore, read accesses to the device cannot be
initiated on two consecutive K clock rises. The internal logic of
the device ignores the second read request. Read accesses can
be initiated on every other K clock rise. Doing so pipelines the
data flow such that data is transferred out of the device on every
rising edge of the output clocks (C and C, or K and K when in
single clock mode).
When the read port is deselected, the CY7C1313KV18 first
completes the pending read transactions. Synchronous internal
circuitry automatically tristates the outputs following the next
rising edge of the positive output clock (C). This enables a
seamless transition between devices without the insertion of wait
states in a depth expanded memory.
Write Operations
Write operations are initiated by asserting WPS active at the
rising edge of the positive input clock (K). On the following K
clock rise the data presented to D[17:0] is latched and stored into
the lower 18-bit write data register, provided BWS[1:0] are both
asserted active. On the subsequent rising edge of the negative
input clock (K) the information presented to D[17:0] is also stored
into the write data register, provided BWS[1:0] are both asserted
active. This process continues for one more cycle until four 18-bit
words (a total of 72 bits) of data are stored in the SRAM. The
72 bits of data are then written into the memory array at the
specified location. Therefore, write accesses to the device
cannot be initiated on two consecutive K clock rises. The internal
logic of the device ignores the second write request. Write
accesses can be initiated on every other rising edge of the
positive input clock (K). Doing so pipelines the data flow such
that 18 bits of data can be transferred into the device on every
rising edge of the input clocks (K and K).
When deselected, the write port ignores all inputs after the
pending write operations are completed.
Byte Write Operations
Byte write operations are supported by the CY7C1313KV18. A
write operation is initiated as described in the Write Operations
section. The bytes that are written are determined by BWS0 and
BWS1, which are sampled with each set of 18-bit data words.
Asserting the appropriate Byte Write Select input during the data
portion of a write latches the data being presented and writes it
into the device. Deasserting the Byte Write Select input during
the data portion of a write enables the data stored in the device
for that byte to remain unaltered. This feature is used to simplify
read, modify, or write operations to a byte write operation.
Single Clock Mode
The CY7C1313KV18 is used with a single clock that controls
both the input and output registers. In this mode the device
recognizes only a single pair of input clocks (K and K) that control
both the input and output registers. This operation is identical to
the operation if the device had zero skew between the K/K and
C/C clocks. All timing parameters remain the same in this mode.
To use this mode of operation, the user must tie C and C HIGH
at power on. This function is a strap option and not alterable
during device operation.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 10 of 33
Concurrent Transactions
The read and write ports on the CY7C1313KV18 operate
independently of one another. As each port latches the address
inputs on different clock edges, the user can read or write to any
location, regardless of the transaction on the other port. If the
ports access the same location when a read follows a write in
successive clock cycles, the SRAM delivers the most recent
information associated with the specified address location. This
includes forwarding data from a write cycle that was initiated on
the previous K clock rise.
Read access and write access must be scheduled such that one
transaction is initiated on any clock cycle. If both ports are
selected on the same K clock rise, the arbitration depends on the
previous state of the SRAM. If both ports are deselected, the
read port takes priority. If a read was initiated on the previous
cycle, the write port takes priority (as read operations cannot be
initiated on consecutive cycles). If a write was initiated on the
previous cycle, the read port takes priority (as write operations
cannot be initiated on consecutive cycles). Therefore, asserting
both port selects active from a deselected state results in
alternating read or write operations being initiated, with the first
access being a read.
Depth Expansion
The CY7C1313KV18 has a port select input for each port. This
enables for easy depth expansion. Both port selects are sampled
on the rising edge of the positive input clock only (K). Each port
select input can deselect the specified port. Deselecting a port
does not affect the other port. All pending transactions (read and
write) are completed before the device is deselected.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and VSS to allow the SRAM to adjust its output
driver impedance. The value of RQ must be 5 × the value of the
intended line impedance driven by the SRAM, the allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175 and 350 , with VDDQ = 1.5 V. The
output impedance is adjusted every 1024 cycles upon power up
to account for drifts in supply voltage and temperature.
Echo Clocks
Echo clocks are provided on the QDR II to simplify data capture
on high speed systems. Two echo clocks are generated by the
QDR II. CQ is referenced with respect to C and CQ is referenced
with respect to C. These are free running clocks and are
synchronized to the output clock of the QDR II. In the single clock
mode, CQ is generated with respect to K and CQ is generated
with respect to K. The timing for the echo clocks is shown in the
Switching Characteristics on page 26.
PLL
These chips use a PLL that is designed to function between
120 MHz and the specified maximum clock frequency. During
power up, when the DOFF is tied HIGH, the PLL is locked after
20 s of stable clock. The PLL can also be reset by slowing or
stopping the input clocks K and K for a minimum of 30 ns.
However, it is not necessary to reset the PLL to lock to the
desired frequency. The PLL automatically locks 20 s after a
stable clock is presented. The PLL may be disabled by applying
ground to the DOFF pin. When the PLL is turned off, the device
behaves in QDR I mode (with one cycle latency and a longer
access time).
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 11 of 33
Application Example
Figure 1 shows four QDR II used in an application.
Figure 1. Application Example
Truth Table
The truth table for CY7C1311KV18, CY7C1911KV18, CY7C1313KV18, and CY7C1315KV18 follow.[2, 3, 4, 5, 6, 7]
Operation KRPS WPS DQ DQ DQ DQ
Write cycle:
Load address on the rising
edge of K; input write data
on two consecutive K and
K rising edges.
L–H H[8] L[9] D(A) at K(t + 1)D(A + 1) at K(t + 1)D(A + 2) at K(t + 2)D(A + 3) at K(t + 2)
Read cycle:
Load address on the rising
edge of K; wait one and a
half cycle; read data on
two consecutive C and C
rising edges.
L–H L[9] XQ(A) at C(t + 1)Q(A + 1) at C(t + 2)Q(A + 2) at C(t + 2)Q(A + 3) at C(t + 3)
NOP: No operation L–H H H D = X
Q = High Z
D = X
Q = High Z
D = X
Q = High Z
D = X
Q = High Z
Standby: Clock stopped Stopped X X Previous state Previous state Previous state Previous state
R = 250ohms
Vt
R
R = 250ohms
Vt
Vt
R
Vt = Vddq/2
R = 50ohms
R
CC#
D
A
SRAM #4
R
P
S
#
W
P
S
#
B
W
S
#K
ZQ
CQ/CQ#
Q
K#
CC#
D
AK
SRAM #1
R
P
S
#
W
P
S
#
B
W
S
#
ZQ
CQ/CQ#
Q
K#
BUS
MASTER
(CPU
or
ASIC)
DATA IN
DATA OUT
Address
RPS#
WPS#
BWS#
Source K
Source K#
Delayed K
Delayed K#
CLKIN/CLKIN#
Notes
2. X = ‘Don't Care’, H = Logic HIGH, L = Logic LOW, represents rising edge.
3. Device powers up deselected with the outputs in a tristate condition.
4. ‘A’ represents address location latched by the devices when transaction was initiated. A + 1, A + 2, and A +3 represents the address sequence in the burst.
5. ‘t’ represents the cycle at which a read/write operation is started. t + 1, t + 2, and t + 3 are the first, second and third clock cycles respectively succeeding the ‘t’ clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. Ensure that when the clock is stopped K = K and C = C = HIGH. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
8. If this signal was LOW to initiate the previous cycle, this signal becomes a ‘Don’t Care’ for this operation.
9. This signal was HIGH on previous K clock rise. Initiating consecutive read or write operations on consecutive K clock rises is not permitted. The device ignores the
second read or write request.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 12 of 33
Write Cycle Descriptions
The write cycle description table for CY7C1311KV18 and CY7C1313KV18 are as follows.[10, 11]
BWS0/
NWS0
BWS1/
NWS1
KKComments
L L L–H During the data portion of a write sequence
CY7C1311KV18 both nibbles (D[7:0]) are written into the device.
CY7C1313KV18 both bytes (D[17:0]) are written into the device.
L L L–H During the data portion of a write sequence
CY7C1311KV18 both nibbles (D[7:0]) are written into the device.
CY7C1313KV18 both bytes (D[17:0]) are written into the device.
L H L–H During the data portion of a write sequence
CY7C1311KV18 only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1313KV18 only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
L H L–H During the data portion of a write sequence
CY7C1311KV18 only the lower nibble (D[3:0]) is written into the device, D[7:4] remains unaltered.
CY7C1313KV18 only the lower byte (D[8:0]) is written into the device, D[17:9] remains unaltered.
H L L–H During the data portion of a write sequence
CY7C1311KV18 only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1313KV18 only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
H L L–H During the data portion of a write sequence
CY7C1311KV18 only the upper nibble (D[7:4]) is written into the device, D[3:0] remains unaltered.
CY7C1313KV18 only the upper byte (D[17:9]) is written into the device, D[8:0] remains unaltered.
H H L–H No data is written into the devices during this portion of a write operation.
H H L–H No data is written into the devices during this portion of a write operation.
Write Cycle Descriptions
The write cycle description table for CY7C1911KV18 is as follows. [10, 11]
BWS0K K
LL–H During the data portion of a write sequence, the single byte (D[8:0]) is written into the device.
L L–H During the data portion of a write sequence, the single byte (D[8:0]) is written into the device.
HL–H No data is written into the device during this portion of a write operation.
H L–H No data is written into the device during this portion of a write operation.
Notes
10. X = ‘Don't Care’, H = Logic HIGH, L = Logic LOW, represents rising edge.
11. Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS0, NWS1, BWS0, BWS1, BWS2, and BWS3 can be altered on
different portions of a write cycle, as long as the setup and hold requirements are achieved.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 13 of 33
Write Cycle Descriptions
The write cycle description table for CY7C1315KV18 follows.[12, 13]
BWS0BWS1BWS2BWS3K K Comments
LLLLL–H During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
LLLLL–H During the data portion of a write sequence, all four bytes (D[35:0]) are written into
the device.
L H H H L–H During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
L H H H L–H During the data portion of a write sequence, only the lower byte (D[8:0]) is written
into the device. D[35:9] remains unaltered.
H L H H L–H During the data portion of a write sequence, only the byte (D[17:9]) is written into
the device. D[8:0] and D[35:18] remains unaltered.
H L H H L–H During the data portion of a write sequence, only the byte (D[17:9]) is written into
the device. D[8:0] and D[35:18] remains unaltered.
H H L H L–H During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
H H L H L–H During the data portion of a write sequence, only the byte (D[26:18]) is written into
the device. D[17:0] and D[35:27] remains unaltered.
H H H L L–H During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
H H H L L–H During the data portion of a write sequence, only the byte (D[35:27]) is written into
the device. D[26:0] remains unaltered.
HHHHL–H No data is written into the device during this portion of a write operation.
HHHHL–H No data is written into the device during this portion of a write operation.
Notes
12. X = ‘Don't Care’, H = Logic HIGH, L = Logic LOW, represents rising edge.
13. Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS0, NWS1, BWS0, BWS1, BWS2, and BWS3 can be altered on
different portions of a write cycle, as long as the setup and hold requirements are achieved.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 14 of 33
IEEE 1149.1 Serial Boundary Scan (JTAG)
These SRAMs incorporate a serial boundary scan test access
port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard #1149.1-2001. The TAP operates using JEDEC
standard 1.8 V I/O logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternatively be connected to VDD through a pull up resistor. TDO
must be left unconnected. Upon power up, the device comes up
in a reset state, which does not interfere with the operation of the
device.
Test Access Port—Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. This pin may be left
unconnected if the TAP is not used. The pin is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI pin is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information about
loading the instruction register, see the TAP Controller State
Diagram on page 16. TDI is internally pulled up and can be
unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.
Test Data-Out (TDO)
The TDO output pin is used to serially clock data out from the
registers. The output is active, depending upon the current state
of the TAP state machine (see Instruction Codes on page 19).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.
Performing a TAP Reset
A reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This reset does not affect the operation of the
SRAM and can be performed when the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a high Z state.
TAP Registers
Registers are connected between the TDI and TDO pins to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction registers. Data
is serially loaded into the TDI pin on the rising edge of TCK. Data
is output on the TDO pin on the falling edge of TCK.
Instruction Register
Three-bit instructions are serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO pins, as shown in TAP Controller Block Diagram on
page 17. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary ‘01’ pattern to allow for
fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that is placed between TDI and
TDO pins. This enables shifting of data through the SRAM with
minimal delay. The bypass register is set LOW (VSS) when the
BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several no connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions are
used to capture the contents of the input and output ring.
The Boundary Scan Order on page 20 shows the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in Identification Register Definitions on
page 19.
TAP Instruction Set
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Instruction
Codes on page 19. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in this section in detail.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 15 of 33
IDCODE
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is supplied a
Test-Logic-Reset state.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High Z state until the next command is supplied during the
Update IR state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.
The TAP controller clock can only operate at a frequency up to
20 MHz, while the SRAM clock operates more than an order of
magnitude faster. Because there is a large difference in the clock
frequencies, it is possible that during the Capture-DR state, an
input or output undergoes a transition. The TAP may then try to
capture a signal while in transition (metastable state). This does
not harm the device, but there is no guarantee as to the value
that is captured. Repeatable results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK captured in the boundary scan register.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required, that is, while the data
captured is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.
EXTEST OUTPUT BUS TRISTATE
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tristate mode.
The boundary scan register has a special bit located at bit #47.
When this scan cell, called the ‘extest output bus tristate’, is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive the
output bus. When LOW, this bit places the output bus into a
High Z condition.
This bit is set by entering the SAMPLE/PRELOAD or EXTEST
command, and then shifting the desired bit into that cell, during
the Shift-DR state. During Update-DR, the value loaded into that
shift-register cell latches into the preload register. When the
EXTEST instruction is entered, this bit directly controls the output
Q-bus pins. Note that this bit is preset HIGH to enable the output
when the device is powered up, and also when the TAP controller
is in the Test-Logic-Reset state.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 16 of 33
TAP Controller State Diagram
The state diagram for the TAP controller follows.[14]
Test-Logic
Reset
Test-Logic/
Idle
Select
DR-Scan
Capture-DR
Shift-DR
Exit1-DR
Pause-DR
Exit2-DR
Update-DR
1
0
1
1
0
1
0
1
0
0
0
1
1
1
0
10
10
0
0
1
0
1
1
0
1
0
0
1
1
0
Select
IR-Scan
Capture-IR
Shift-IR
Exit1-IR
Pause-IR
Exit2-IR
Update-IR
Note
14. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 17 of 33
TAP Controller Block Diagram
TAP Electrical Characteristics
Over the Operating Range[15, 16, 17]
Parameter Description Test Conditions Min Max Unit
VOH1 Output HIGH voltage IOH =2.0 mA 1.4 V
VOH2 Output HIGH voltage IOH =100 A1.6 V
VOL1 Output LOW voltage IOL = 2.0 mA 0.4 V
VOL2 Output LOW voltage IOL = 100 A 0.2 V
VIH Input HIGH voltage 0.65 VDD VDD + 0.3 V
VIL Input LOW voltage –0.3 0.35 VDD V
IXInput and output load current GND VI VDD –5 5A
0
012..29
3031
Boundary Scan Register
Identification Register
012..
.
.106
012
Instruction Register
Bypass Register
Selection
Circuitry
Selection
Circuitry
TAP Controller
TDI TDO
TCK
TMS
Notes
15. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics Table.
16. Overshoot: VIH(AC) < VDDQ + 0.85 V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > 1.5 V (Pulse width less than tCYC/2).
17. All voltage referenced to Ground.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 18 of 33
TAP AC Switching Characteristics
Over the Operating Range[18, 19]
Parameter Description Min Max Unit
tTCYC TCK Clock Cycle Time 50 ns
tTF TCK Clock Frequency 20 MHz
tTH TCK Clock HIGH 20 ns
tTL TCK Clock LOW 20 ns
Setup Times
tTMSS TMS Setup to TCK Clock Rise 5 ns
tTDIS TDI Setup to TCK Clock Rise 5 ns
tCS Capture Setup to TCK Rise 5 ns
Hold Times
tTMSH TMS Hold after TCK Clock Rise 5 ns
tTDIH TDI Hold after Clock Rise 5 ns
tCH Capture Hold after Clock Rise 5 ns
Output Times
tTDOV TCK Clock LOW to TDO Valid 10 ns
tTDOX TCK Clock LOW to TDO Invalid 0 ns
TAP Timing and Test Conditions
Figure 2 shows the TAP timing and test conditions.[19]
Figure 2. TAP Timing and Test Conditions
t
TL
t
TH
(a)
TDO
C
L
= 20 pF
Z
0
= 50
GND
0.9 V
50
1.8 V
0 V
ALL INPUT PULSES
0.9 V
Test Clock
Test Mode Select
TCK
TMS
Test Data In
TDI
Test Data Out
t
TCYC
t
TMSH
t
TMSS
t
TDIS
t
TDIH
t
TDOV
t
TDOX
TDO
Notes
18. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
19. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 19 of 33
Identification Register Definitions
Instruction Field Value Description
CY7C1311KV18 CY7C1911KV18 CY7C1313KV18 CY7C1315KV18
Revision number
(31:29)
000 000 000 000 Version number.
Cypress device ID
(28:12)
11010011011000101 11010011011001101 11010011011010101 11010011011100101 Defines the type of
SRAM.
Cypress JEDEC ID
(11:1)
00000110100 00000110100 00000110100 00000110100 Allows unique
identification of
SRAM vendor.
ID register
presence (0)
1111Indicates the
presence of an ID
register.
Scan Register Sizes
Register Name Bit Size
Instruction 3
Bypass 1
ID 32
Boundary Scan 107
Instruction Codes
Instruction Code Description
EXTEST 000 Captures the input and output ring contents.
IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operation.
SAMPLE Z 010 Captures the input and output contents. Places the boundary scan register between TDI and
TDO. Forces all SRAM output drivers to a High Z state.
RESERVED 011 Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD 100 Captures the input and output ring contents. Places the boundary scan register between TDI
and TDO. Does not affect the SRAM operation.
RESERVED 101 Do Not Use: This instruction is reserved for future use.
RESERVED 110 Do Not Use: This instruction is reserved for future use.
BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM
operation.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 20 of 33
Boundary Scan Order
Bit # Bump ID Bit # Bump ID Bit # Bump ID Bit # Bump ID
06R 28 10G 56 6A 84 2J
16P 29 9G 57 5B 85 3K
26N 30 11F 58 5A 86 3J
37P 31 11G 59 4A 87 2K
47N 32 9F 60 5C 88 1K
57R 33 10F 61 4B 89 2L
68R 34 11E 62 3A 90 3L
78P 35 10E 63 1H 91 1M
89R 36 10D 64 1A 92 1L
911P 37 9E 65 2B 93 3N
10 10P 38 10C 66 3B 94 3M
11 10N 39 11D 67 1C 95 1N
12 9P 40 9C 68 1B 96 2M
13 10M 41 9D 69 3D 97 3P
14 11N 42 11B 70 3C 98 2N
15 9M 43 11C 71 1D 99 2P
16 9N 44 9B 72 2C 100 1P
17 11L 45 10B 73 3E 101 3R
18 11M 46 11A 74 2D 102 4R
19 9L 47 Internal 75 2E 103 4P
20 10L 48 9A 76 1E 104 5P
21 11K 49 8B 77 2F 105 5N
22 10K 50 7C 78 3F 106 5R
23 9J 51 6C 79 1G
24 9K 52 8A 80 1F
25 10J 53 7A 81 3G
26 11J 54 7B 82 2G
27 11H 55 6B 83 1J
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 21 of 33
Power Up Sequence in QDR II SRAM
QDR II SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations.
Power Up Sequence
Apply power and drive DOFF either HIGH or LOW (All other
inputs can be HIGH or LOW).
Apply VDD before VDDQ.
Apply VDDQ before VREF or at the same time as VREF
.
Drive DOFF HIGH.
Provide stable DOFF (HIGH), power and clock (K, K) for 20 s
to lock the PLL.
PLL Constraints
PLL uses K clock as its synchronizing input. The input must
have low phase jitter, which is specified as tKC Var.
The PLL functions at frequencies down to 120 MHz.
If the input clock is unstable and the PLL is enabled, then the
PLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide 20 s of stable clock to
relock to the desired clock frequency.
Figure 3. Power Up Waveforms
> 20Ps Stable clock
Start Normal
Operation
DOFF
Stable(< +/- 0.1V DC per 50ns )
Fix HIGH (or tie to V
DDQ)
K
K
DDQDD
VV
/DDQDD
VV
/
Clock Start (Clock Starts after Stable)
DDQ
DD
VV
/
~
~
~
~
Unstable Clock
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 22 of 33
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage temperature ................................ –65 C to +150 C
Ambient temperature with power applied . –55 C to +125 C
Supply voltage on VDD relative to GND........–0.5 V to +2.9 V
Supply voltage on VDDQ relative to GND....... –0.5 V to +VDD
DC applied to outputs in High Z ........ –0.5 V to VDDQ + 0.3 V
DC input voltage[20] ............................. –0.5 V to VDD + 0.3 V
Current into outputs (LOW) ......................................... 20 mA
Static discharge voltage (MIL-STD-883, M. 3015).. > 2001 V
Latch up current..................................................... > 200 mA
Operating Range
Range
Ambient
Temperature (TA) VDD[21] VDDQ[21]
Commercial 0 C to +70 C 1.8 ± 0.1 V 1.4 V to
VDD
Industrial –40 °C to +85 °C
Neutron Soft Error Immunity
Parameter Description Test
Conditions Typ Max* Unit
LSBU Logical
single-bit
upsets
25 °C 197 216 FIT/
Mb
LMBU Logical
multi-bit
upsets
25 °C 00.01 FIT/
Mb
SEL Single event
latch up
85 °C 00.1 FIT/
Dev
* No LMBU or SEL events occurred during testing; this column represents a
statistical 2, 95% confidence limit calculation. For more details refer to Appli-
cation Note Accelerated Neutron SER Testing and Calculation of Terrestrial
Failure Rates - AN54908
Electrical Characteristics
DC Electrical Characteristics
Over the Operating Range[22]
Parameter Description Test Conditions Min Typ Max Unit
VDD Power supply voltage 1.7 1.8 1.9 V
VDDQ I/O supply voltage 1.4 1.5 VDD V
VOH Output HIGH voltage Note 23 VDDQ/2 – 0.12 VDDQ/2 + 0.12 V
VOL Output LOW voltage Note 24 VDDQ/2 – 0.12 VDDQ/2 + 0.12 V
VOH(LOW) Output HIGH voltage IOH =0.1 mA, nominal impedance VDDQ – 0.2 VDDQ V
VOL(LOW) Output LOW voltage IOL = 0.1 mA, nominal impedance VSS 0.2 V
VIH Input HIGH voltage VREF + 0.1 VDDQ + 0.3 V
VIL Input LOW voltage –0.3 VREF – 0.1 V
IXInput leakage current GND VI VDDQ 5 5 A
IOZ Output leakage current GND VI VDDQ, output disabled 5 5 A
VREF Input reference voltage[25] Typical value = 0.75 V 0.68 0.75 0.95 V
Notes
20. Overshoot: VIH(AC) < VDDQ + 0.85 V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > 1.5 V (Pulse width less than tCYC/2).
21. Power up: Assumes a linear ramp from 0 V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
22. All voltage referenced to Ground.
23. Output are impedance controlled. IOH = (VDDQ/2)/(RQ/5) for values of 175 ohms <= RQ <= 350 .
24. Output are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175 ohms <= RQ <= 350 ohms.
25. VREF (min) = 0.68 V or 0.46 VDDQ, whichever is larger, VREF (max) = 0.95 V or 0.54 VDDQ, whichever is smaller.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 23 of 33
IDD [26] VDD operating supply VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
333 MHz (× 8) 520 mA
(× 9) 520
(× 18) 530
(× 36) 730
300 MHz (× 8) 490 mA
(× 9) 490
(× 18) 500
(× 36) 670
250 MHz (× 8) 430 mA
(× 9) 430
(× 18) 440
(× 36) 590
200 MHz (× 8) 380 mA
(× 9) 380
(× 18) 390
(× 36) 500
167 MHz (× 8) 340 mA
(× 9) 340
(× 18) 350
(× 36) 450
Electrical Characteristics (continued)
DC Electrical Characteristics
Over the Operating Range[22]
Parameter Description Test Conditions Min Typ Max Unit
Note
26. The operation current is calculated with 50% read cycle and 50% write cycle.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 24 of 33
ISB1 Automatic power down
current
Max VDD,
Both ports deselected,
VIN VIH or VIN VIL
f = fMAX = 1/tCYC,
inputs static
333 MHz (× 8) 270 mA
(× 9) 270
(× 18) 270
(× 36) 270
300 MHz (× 8) 260 mA
(× 9) 260
(× 18) 260
(× 36) 260
250 MHz (× 8) 250 mA
(× 9) 250
(× 18) 250
(× 36) 250
200 MHz (× 8) 250 mA
(× 9) 250
(× 18) 250
(× 36) 250
167 MHz (× 8) 250 mA
(× 9) 250
(× 18) 250
(× 36) 250
AC Electrical Characteristics
Over the Operating Range[27]
Parameter Description Test Conditions Min Typ Max Unit
VIH Input HIGH voltage VREF + 0.2 V
VIL Input LOW voltage VREF – 0.2 V
Note
27. Overshoot: VIH(AC) < VDDQ + 0.85 V (Pulse width less than tCYC/2), Undershoot: VIL(AC) > 1.5 V (Pulse width less than tCYC/2).
Electrical Characteristics (continued)
DC Electrical Characteristics
Over the Operating Range[22]
Parameter Description Test Conditions Min Typ Max Unit
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 25 of 33
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter Description Test Conditions Max Unit
CIN Input capacitance TA = 25 C, f = 1 MHz, VDD = 1.8 V, VDDQ = 1.5 V 4pF
COOutput capacitance 4pF
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
Parameter Description Test Conditions 165 FBGA
Package Unit
JA Thermal resistance
(junction to ambient)
Test conditions follow standard test methods and
procedures for measuring thermal impedance, in
accordance with EIA/JESD51.
13.7 °C/W
JC Thermal resistance
(junction to case)
3.73 °C/W
Figure 4. AC Test Loads and Waveforms
1.25 V
0.25 V
R = 50
5pF
INCLUDING
JIG AND
SCOPE
All Input Pulses
Device RL= 50
Z0= 50
VREF = 0.75 V
VREF = 0.75 V
[28]
0.75 V
Under
Tes t
0.75 V
Device
Under
Te s t
OUTPUT
0.75 V
VREF
VREF
OUTPUT
ZQ
ZQ
(a)
Slew Rate = 2 V/ns
RQ =
250
(b)
RQ =
250
Note
28. Unless otherwise noted, test conditions are based on signal transition time of 2 V/ns, timing reference levels of 0.75 V, Vref = 0.75 V, RQ = 250 , VDDQ = 1.5 V, input
pulse levels of 0.25 V to 1.25 V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of Figure 4.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 26 of 33
Switching Characteristics
Over the Operating Range[29, 30]
Cypress
Parameter
Consortium
Parameter Description
333 MHz 300 MHz 250 MHz 200 MHz 167 MHz
Unit
Min Max Min Max Min Max Min Max Min Max
tPOWER VDD(typical) to the First Access[31] 1 1 1 1 1 ms
tCYC tKHKH K Clock and C Clock Cycle Time 3.0 8.4 3.3 8.4 4.0 8.4 5.0 8.4 6.0 8.4 ns
tKH tKHKL Input Clock (K/K; C/C) HIGH 1.20 1.32 1.6 2.0 2.4 ns
tKL tKLKH Input Clock (K/K; C/C) LOW 1.20 1.32 1.6 2.0 2.4 ns
tKHKH tKHKH K Clock Rise to K Clock Rise and C
to C Rise (rising edge to rising edge)
1.35 1.49 1.8 2.2 2.7 ns
tKHCH tKHCH K/K Clock Rise to C/C Clock Rise
(rising edge to rising edge)
01.30 01.45 01.8 02.2 02.7 ns
Setup Times
tSA tAVKH Address Setup to K Clock Rise 0.4 0.4 0.5 0.6 0.7 ns
tSC tIVKH Control Setup to K Clock Rise
(RPS, WPS)
0.4 0.4 0.5 0.6 0.7 ns
tSCDDR tIVKH Double data rate control setup to
Clock (K/K) Rise
(BWS0, BWS1, BWS2, BWS3)
0.3 0.3 0.35 0.4 0.5 ns
tSD tDVKH D[X:0] Setup to Clock (K/K) Rise 0.3 0.3 0.35 0.4 0.5 ns
Hold Times
tHA tKHAX Address Hold after K Clock Rise 0.4 0.4 0.5 0.6 0.7 ns
tHC tKHIX Control Hold after K Clock Rise
(RPS, WPS)
0.4 0.4 0.5 0.6 0.7 ns
tHCDDR tKHIX Double data rate control Hold after
Clock (K/K) Rise
(BWS0, BWS1, BWS2, BWS3)
0.3 0.3 0.35 0.4 0.5 ns
tHD tKHDX D[X:0] Hold after Clock (K/K) Rise 0.3 0.3 0.35 0.4 0.5 ns
Notes
29. Unless otherwise noted, test conditions are based on signal transition time of 2 V/ns, timing reference levels of 0.75 V, Vref = 0.75 V, RQ = 250 , VDDQ = 1.5 V, input
pulse levels of 0.25 V to 1.25 V, and output loading of the specified IOL/IOH and load capacitance shown in (a) of Figure 4.
30. When a part with a maximum frequency above 167 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is operated
and outputs data with the output timings of that frequency range.
31. This part has a voltage regulator internally; tPOWER is the time that the power must be supplied above VDD minimum initially before a read or write operation is initiated.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 27 of 33
Output Times
tCO tCHQV C/C Clock Rise (or K/K in Single
Clock mode) to Data Valid
0.45 0.45 0.45 0.45 0.50 ns
tDOH tCHQX Data Output Hold after Output C/C
Clock Rise (Active To Active)
–0.45 –0.45 –0.45 –0.45 –0.50 ns
tCCQO tCHCQV C/C Clock Rise to Echo Clock Valid 0.45 0.45 0.45 0.45 0.50 ns
tCQOH tCHCQX Echo Clock Hold after C/C Clock
Rise
–0.45 –0.45 –0.45 –0.45 –0.50 ns
tCQD tCQHQV Echo Clock High To Data Valid 0.25 0.27 0.30 0.35 0.40 ns
tCQDOH tCQHQX Echo Clock High To Data Invalid –0.25 –0.27 –0.30 –0.35 –0.40 ns
tCQH tCQHCQL OutPut Clock (CQ/CQ) HIGH[32] 1.25 1.4 1.75 2.25 2.75 ns
tCQHCQHtCQHCQHCQ Clock Rise to CQ Clock Rise
(rising edge to rising edge)[32]1.25 1.4 1.75 2.25 2.75 ns
tCHZ tCHQZ Clock (C/C) Rise to High Z
(Active to High Z)[33, 34]
0.45 0.45 0.45 0.45 0.50 ns
tCLZ tCHQX1 Clock (C/C) Rise to Low Z [33, 34] –0.45 –0.45 –0.45 –0.45 –0.50 ns
PLL Timing
tKC Var tKC Var Clock Phase Jitter 0.20 0.20 0.20 0.20 0.20 ns
tKC lock tKC lock PLL Lock Time (K, C)[35] 20 20 20 20 20 s
tKC Reset tKC Reset K Static to PLL Reset 30 30 30 30 30 ns
Switching Characteristics (continued)
Over the Operating Range[29, 30]
Cypress
Parameter
Consortium
Parameter Description
333 MHz 300 MHz 250 MHz 200 MHz 167 MHz
Unit
Min Max Min Max Min Max Min Max Min Max
Notes
32. These parameters are extrapolated from the input timing parameters (tCYC/2 - 250 ps, where 250 ps is the internal jitter). These parameters are only guaranteed by
design and are not tested in production.
33. tCHZ, tCLZ, are specified with a load capacitance of 5 pF as in (b) of AC Test Loads and Waveforms. Transition is measured ± 100 mV from steady-state voltage.
34. At any voltage and temperature tCHZ is less than tCLZ and tCHZ less than tCO.
35. For frequencies 300 MHz or below, the Cypress QDR II devices surpass the QDR consortium specification for PLL lock time (tKC lock) of 20 µs (min. spec.) and will
lock after 1024 clock cycles (min. spec.), after a stable clock is presented, per the previous 90 nm version.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 28 of 33
Switching Waveforms
Figure 5. Read/Write/Deselect Sequence[36, 37, 38]
K
12345
67
RPS
WPS
A
Q
D
C
C
READ READWRITE WRITE
NOP NOP
DON’T CARE UNDEFINED
CQ
CQ
K
A0 A1
tKH tKHKH
tKL tCYC
ttHC
tSA tHA
A2
SC tt
HCSC
A3
tKHCH
tKHCH
tCQD
tCLZ
DOH
tCHZ
t
ttKL
tCYC
tCCQO
tCCQO
tCQOH
tCQOH
KHKH KH
Q00 Q03
Q01 Q02 Q20 Q23
Q21 Q22
tCO tCQDOH
t
tCQH tCQHCQH
D10 D11 D12 D13
tSD
tHD
tSD
tHD
D30 D31 D32 D33
Notes
36. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0+1.
37. Outputs are disabled (High Z) one clock cycle after a NOP.
38. In this example, if address A2 = A1, then data Q20 = D10, Q21 = D11, Q22 = D12, and Q23 = D13. Write data is forwarded immediately as read results. This note
applies to the whole diagram.
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 29 of 33
Ordering Information
The following table contains only the parts that are currently available. If you do not see what you are looking for, contact your local
sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page at
http://www.cypress.com/products
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Table 1. Ordering Information
Speed
(MHz) Ordering Code
Package
Diagram Package Type
Operating
Range
333 CY7C1911KV18-333BZC 51-85180 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Commercial
CY7C1313KV18-333BZC
CY7C1315KV18-333BZC
300 CY7C1911KV18-300BZC 51-85180 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Commercial
CY7C1315KV18-300BZC
CY7C1911KV18-300BZXC 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Pb-free
CY7C1315KV18-300BZXC
250 CY7C1911KV18-250BZC 51-85180 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Commercial
CY7C1313KV18-250BZC
CY7C1315KV18-250BZC
CY7C1911KV18-250BZXC 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Pb-free
CY7C1315KV18-250BZXC
CY7C1313KV18-250BZI 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Industrial
CY7C1315KV18-250BZI
CY7C1313KV18-250BZXI 165-ball fine-pitch ball grid array (13 × 15 × 1.4 mm) Pb-free
CY7C1315KV18-250BZXI
Ordering Code Definitions
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 30 of 33
Package Diagram
Figure 6. 165-ball FBGA (13 × 15 × 1.4 mm), 51-85180
A
1
PIN 1 CORNER
15.00±0.10
13.00±0.10
7.00
1.00
Ø0.50 (165X)
Ø0.25 M C A B
Ø0.08 M C
B
A
0.15(4X)
SEATING PLANE
0.53±0.05
0.25 C
0.15 C
PIN 1 CORNER
TOP VIEW
BOTTOM VIEW
2345678910
10.00
14.00
B
C
D
E
F
G
H
J
K
L
M
N
11
1110986754321
P
R
P
R
K
M
N
L
J
H
G
F
E
D
C
B
A
A
15.00±0.10
13.00±0.10
B
C
1.00
5.00
0.36
-0.06
+0.14
1.40 MAX.
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)
NOTES :
PACKAGE WEIGHT : 0.475g
JEDEC REFERENCE : MO-216 / ISSUE E
PACKAGE CODE : BB0AC
51-85180 *C
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 31 of 33
Acronyms Document Conventions
Units of Measure
Acronym Description
DDR double data rate
FBGA fine-pitch ball grid array
HSTL high-speed transceiver logic
I/O input/output
JTAG joint test action group
LSB least significant bit
LMBU logical multiple bit upset
LSBU logical single bit upset
MSB most significant bit
PLL phase locked loop
QDR quad data rate
SEL single event latch up
SRAM static random access memory
TAP test access port
TCK test clock
TMS test mode select
TDI test data-in
TDO test data-out
Symbol Unit of Measure
µs micro seconds
ns nano seconds
ohms
Kkilo ohms
VVolts
µA micro Amperes
mA milli Amperes
mm milli meter
ms milli seconds
MHz Mega Hertz
pF pico Farad
WWatts
°C degree Celcius
[+] Feedback
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
Document Number: 001-58904 Rev. *C Page 32 of 33
Document History Page
Document Title: CY7C1311KV18/CY7C1911KV18/CY7C1313KV18/CY7C1315KV18, 18-Mbit QDR® II SRAM Four-Word Burst
Architecture
Document Number: 001-58904
Rev. ECN No. Orig. of
Change
Submission
Date Description of change
** 2860800 VKN 01/20/2010 New datasheet
*A 2897083 AJU 03/22/10 Removed inactive parts
*B 3076901 NJY 11/03/2010 Changed status from Preliminary to Final.
Updated Ordering Information.
Added Ordering Code Definitions.
Added Acronyms and Document Conventions.
*C 3167511 NJY 02/09/2011 Added Note 35.
Updated Ordering Information.
[+] Feedback
Document Number: 001-58904 Rev. *C Revised March 1, 2011 Page 33 of 33
QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All product and company names mentioned in this document
are the trademarks of their respective holders.
CY7C1311KV18, CY7C1911KV18
CY7C1313KV18, CY7C1315KV18
© Cypress Semiconductor Corporation, 2010-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive cypress.com/go/automotive
Clocks & Buffers cypress.com/go/clocks
Interface cypress.com/go/interface
Lighting & Power Control cypress.com/go/powerpsoc
cypress.com/go/plc
Memory cypress.com/go/memory
Optical & Image Sensing cypress.com/go/image
PSoC cypress.com/go/psoc
Touch Sensing cypress.com/go/touch
USB Controllers cypress.com/go/USB
Wireless/RF cypress.com/go/wireless
PSoC Solutions
psoc.cypress.com/solutions
PSoC 1 | PSoC 3 | PSoC 5
[+] Feedback