PTGL07BD680N3B51B0 - Murata - Datasheet.Support

Cat.No.R03E-3

Murata

Manufacturing Co., Ltd.

NTC/PTC Thermistors

for Automotive

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

2
3
5
6
4
1
Part Numbering 2
Basic Characteristics of NTC Thermistor 6
Basic Characteristics of POSISTORr7
NTC Thermistor Chip Type 0402 (1005) Size  8
NTC Thermistor Chip Type 0603 (1608) Size  10
For NTC Thermistors Chip Type Standard Land Pattern Dimensions 11
For NTC Thermistors Chip Type Temperature Characteristics (Center Value) 12
For NTC Thermistors Chip Type Specifications and Test Methods  15
For NTC Thermistors Chip Type !Caution/Notice 17
NTC Thermistor Lead Type for Temperature Sensor 20
For NTC Thermistors Lead Type Temperature Characteristics (Center Value) 21
For NTC Thermistors Lead Type Specifications and Test Methods 22
For NTC Thermistors Lead Type !Caution/Notice 23
PTC Thermistor (POSISTORr) for Overheat Sensing Chip Type 0603 (1608) Size
24
Chip Type of POSISTORr for Overheat Protection Specifications and Test Methods 27
PTC Thermistor (POSISTORr) for Overcurrent Protection Chip Type 0805 (2012)  Size
29
Chip Type of POSISTORr for Overheat Protection Specifications and Test Methods 31
For POSISTORr Chip Type !Caution/Notice 33
PTC Thermistor (POSISTORr) for Overcurrent Protection Lead Type 39
POSISTORr Lead Type for Overheat Protection Specifications and Test Methods 49
POSISTORr Lead Type for Overheat Protection !Caution/Notice 52
For NTC Thermistors Chip Type Package 53
For NTC Thermistors Lead Type Package 55
For POSISTORr Chip Type Package 56
For POSISTORr Lead Type Package 57
POSISTORr and "POSISTOR" in this catalog are
the trademarks of Murata Manufacturing Co., Ltd.
CONTENTS
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Recycled Paper
1
2
3
4
5
6
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore,  it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our 
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note R03E.pdf
07.3.21

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

o Part Numbering

qProduct ID

wSeries

yResistance Tolerance

uIndividual Specifications

NTC Thermistors for Temperature Compensation Chip Type

NC NTC Thermistors Chip Type

E

F

J

P

±3%

±1%

±5%

0S

Individual Specifications

Product ID

Code

Series

Resistance Tolerance

Code

(Part Number)

tResistance

Expressed by three figures. The unit is ohm (Ω). The first and

second figures are significant digits, and the third figure

expresses the number of zeros which follow the two figures.

Structures and others are expressed by two figures.

102

103

104

Ex.)

1kΩ

10kΩ

100kΩ

Code Resistance

for Automotive

iPackaging

RB

RC

Paper Taping 4mm Pitch (4000 pcs.)

Paper Taping 2mm Pitch (10000 pcs.)

Code Packaging

Plated Termination Series

eDimensions (LgW)

15

18

Code Dimensions (LgW)

1.00g0.50mm

1.60g0.80mm

EIA

0402

0603

rTemperature Characteristics

WB

WD

WF

WL

WM

XC

XF

XQ

XH

XM

XV

XW

Code Temperature Characteristics

Nominal B-Constant 4050e4099K

Nominal B-Constant 4150e4199K

Nominal B-Constant 4250e4299K

Nominal B-Constant 4450e4499K

Nominal B-Constant 4500e4549K

Nominal B-Constant 3100e3149K

Nominal B-Constant 3250e3299K

Nominal B-Constant 3650e3699K

Nominal B-Constant 3350e3399K

Nominal B-Constant 3500e3549K

Nominal B-Constant 3900e3949K

Nominal B-Constant 3950e3999K

y

J

e

18

w

P

r

XH

t

103

u

0S

i

RB

NC

q

2

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

qProduct ID

wSeries

tResistance Tolerance

yIndividual Specifications

NTC Thermistors for Temperature Sensor Lead Type

NT NTC Thermistors

E

F

±3%

±1%

E1

N6

Individual Specifications

Product ID

Code Resistance Tolerance

Code

(Part Number)

rResistance

Expressed by three figures. The unit is ohm (Ω). The first and

second figures are significant digits, and the third figure

expresses the number of zeros which follow the two figures.

A lead structure and other specifications are expressed by two digits.

202

203

Ex.)

2kΩ

20kΩ

Code Resistance

Bulk

Standard Taping

SS0

Temperature Sensors for Automotive Equipment

Code

uPackaging

A0

B0

Ammo Pack

Bulk

Code Packaging

Series

eTemperature Characteristics

WB

WC

WD

WF

XM

XH

XR

XV

Nominal B-Constant 4050e4099K

Nominal B-Constant 4100e4149K

Nominal B-Constant 4150e4199K

Nominal B-Constant 4250e4299K

Nominal B-Constant 3500e3549K

Nominal B-Constant 3350e3399K

Nominal B-Constant 3700e3749K

Nominal B-Constant 3900e3949K

Code Temperature Characteristics

t

F

w

SS0

e

XH

r

103

y

E1

u

B0

NT

q

y

Q

e

18

w

F

r

BB

t

471

u

S2

i

RB

PR

q

qProduct ID

wSeries

rTemperature Characteristics

yResistance Tolerance

uIndividual Specifications

PTC Thermistors (POSISTORr) for Overheat Sensing Chip Type

PR PTC Thermistors Chip Type

Q

R

Ffor Overheat Sensing

AR

AS

BA

BB

BC

BD

BE

BF

BG

Curie Point 120°C

Curie Point 130°C

Curie Point 110°C

Curie Point 100°C

Curie Point 90°C

Curie Point 80°C

Curie Point 70°C

Curie Point 60°C

Curie Point 50°C

Special Tolerance

Temperature Characteristics

S2

Individual Specifications

Product ID

Code

Series

Resistance Tolerance

±5°C

±3°C

Sensing Temp. Tolerance

Code

(Part Number)

tResistance

Expressed by three figures. The unit is ohm (Ω). The first and

second figures are significant digits, and the third figure

expresses the number of zeros which follow the two figures.

471

Ex.)

470Ω

Code Resistance

for Automotive

eDimensions (LgW)

18 1.60g0.80mm

Code Dimensions (LgW)

iPackaging

RB

Packaging

Code

Paper Taping (4mm Pitch) (4000 pcs.)

3

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

y

M

e

21

w

G

r

AR

t

420

u

S1

i

RA

PR

q

qProduct ID

wSeries

rTemperature Characteristics

yResistance Tolerance

uIndividual Specifications

PTC Thermistors (POSISTORr) for Circuit Protection

PR PTC Thermistors Chip Type M

Q

Gfor Overcurrent Protection

AR Curie Point 120°C

±20%

Special Tolerance

Temperature Characteristics

S1

Individual Specifications

Product ID

Code

Series

Resistance Tolerance

Code

(Part Number)

tResistance

Expressed by three-digit alphanamerics. The unit is ohm (Ω). The

first and second figures are significant digits, and the third figure

expresses the number of zeros which follow the two figures. If

there is a decimal point, it is expressed by the capital letter "R". In

this case, all figures are significant digits.

420

471

Ex.)

42Ω

470Ω

Code Resistance

for Automotive

eDimensions (LgW)

21 2.00g1.25mm

Code Dimensions (LgW) iPackaging

RA

RK

Packaging

Code

Embossed Taping (4mm Pitch) (4000 pcs.)

Embossed Taping (4mm Pitch) (3000 pcs.)

4

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

qProduct ID

eDimensions

uResistance Tolerance

iIndividual Specifications

PTC Thermistors (POSISTORr) for Circuit Protection Lead Type

PT PTC Thermistors

K

M

±10%

±20%

4B51

Individual Specifications

Product ID

Code Resistance Tolerance

Code

(Part Number)

yResistance

Expressed by three-digit alphanamerics. The unit is ohm (Ω). The

first and second figures are significant digits, and the third figure

expresses the number of zeros which follow the two figures. If

there is a decimal point, it is expressed by the capital letter "R". In

this case, all figures are significant digits.

R22

2R2

220

Ex.)

0.22Ω

2.2Ω

22Ω

Code Resistance

Lead Type, others

oPackaging

A0

B0

Packaging

Code

Ammo Pack

Bulk

wSeries

GL for Circuit Protection Lead Type

Code Series

rIndividual Specifications

4

5

6

7

9

A

C

E

Sfor Automotive

Individual Specifications

Code

Dimensions

tTemperature Characteristics

AR

AS

Curie Point 120°C

Curie Point 130°C

Temperature CharacteristicsCode

Nominal Body Diameter 4mm Series

Nominal Body Diameter 5mm Series

Nominal Body Diameter 6mm Series

Nominal Body Diameter 7mm Series

Nominal Body Diameter 9mm Series

Nominal Body Diameter 10mm Series

Nominal Body Diameter 12mm Series

Nominal Body Diameter 14mm Series

w

GL

PT

qur

AS

t

220

y

K

i

4B51

o

B0

S

e

4

5

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

6

1. Zero-power Resistance of Thermistor: R

2. B-Constant

Measured by zero-power in specified ambient

temperatures.

R=R0 expB (1/T-1/T0)..............(1)

R: Resistance in ambient temperature T (K)

(K: absolute temperature)

R0: Resistance in ambient temperature T0 (K)

B: B-constant of Thermistor

as (1) formula

B=Rn (R/R0) / (1/T-1/T0)............(2)

3. Thermal Dissipation Constant

When electric power P (mW) is spent in ambient

temperature T1 and thermistor temperature rises T2,

there is a formula as follows

P=C (T2-T1)..................(3)

C: Thermal dissipation constant (mW/°C)

Thermal dissipation constant is varied with dimensions,

measurement conditions, etc.

4. Thermal Time Constant

Period in which Termistor's temperature will change

63.2% of its temperature difference from ambient

temperature T0 (°C) to T1 (°C).

5. Rated Electric Power

Shows necessary electric power that Thermistor's

temperature rises 100˚C by self heating in ambient

temperature 25˚C.

6. Permissive Operating Current

It is possible to keep Thermistor's temperature rising max.

1˚C.

Resistance vs. Temperature

!Basic Characteristics

Thermal Time Constant

102

101

Resistance vs. Temperature Characteristics, R/R25

−20 Temperature (˚C)

0 20406080 120100

10−2

10−1

1

B=3450

B=3900

B=4100

Basic Characteristics of NTC Thermistor

T1

T0

Time

63.2%

X

Temperature

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

7

1. Resistance - Temperature Characteristics

POSISTORr has three main characteristics.

Although there is a negligible difference between the

normal and "Curie Point" temperature, POSISTORr

shows almost constant resistance - temperature

characteristics. Yet they have resistance - temperature

characteristics that cause resistance to sharply increase

when the temperature exceeds the Curie Point.

The Curie Point (C.P.) is defined as temperature which

the resistance value is twice the one at 25 °C.

2. Current - Voltage Characteristics (Static Characteristics)

This shows the relation between applied voltage when

voltage applied to POSISTORr causes balancing of

inner heating and outer thermal dissipation and stabilized

current. This has both a maximum point of current and

constant output power.

3. Current - Time Characteristics (Dynamic Characteristics)

This shows the relation between current and time before

inner heating and outer thermal dissipation arrive at

equilibrium state. This features having large initial current

and abruptly continuous attenuating portion.

Resistance - Temperature Characteristic

!Basic Characteristics

Resistance Change Ratio, R/R25

105

104

103

102

10

1

0 50 100 150 200

Temperature (˚C)

Current - Voltage Characteristics (Static Characteristics)

Current - Time Characteristics (Dynamic Characteristics)

Ta=25˚C

10

1

3

2

0.1 1 10 10

Current (mA)

Voltage (V)

1.5

1.0

0.5

Current (A)

Time (sec.)

Ta=25˚C

BD BC BB AR

Basic Characteristics of POSISTORr

C.P. (AR: 120°C)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

8

1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

NTC/PTC Thermistors for Automotive

NTC Thermistor Chip Type 0402 (1005) Size (Meet AEC-Q200rev.C)

0402/0603 sized Chip NTC Thermistors have Ni barrier

termination and provide excellent solderability

and offer high stability in environment by unique

inner construction.

■ Features

1. NCP15xx0S series can meet AEC-Q200rev.C

requirements

2. Excellent solderability and high stability in

environment

3. Excellent long time aging stability

4. High accuracy in resistance and B-constant

5. Reflow soldering possible

6. Lead is not contained in the product

7. NCP15 series are recognized by UL

(UL1434, File No.E137188 Vol.2, Sec.2).

■ Applications

1. Car audio, car navigation

2. Various engine control units

3. Circuits for ETC equipment

4. Various motor driving circuits

5. Temperature compensation for various circuits

Electrode

(Ag System + Ni Plating + Sn Plating)

0.25±0.10 0.25±0.10

1.0±0.05

(in mm)

0.5±0.05

Part Number Resistance

(25°C)

(ohm)

B-Constant

(25-50°C)

(K)

Permissive Operating

Current (25°C)

(mA)

Rated Electric

Power (25°C)

(mW)

Typical Dissipation

Constant (25°C)

(mW/°C)

Operating

Temperature Range

(°C)

NCP15XC220p0SRC 22 3100 ±3% 6.70 100 1.0 -40 to 125

NCP15XC330p0SRC 33 3100 ±3% 5.50 100 1.0 -40 to 125

NCP15XC470p0SRC 47 3100 ±3% 4.60 100 1.0 -40 to 125

NCP15XC680p0SRC 68 3100 ±3% 3.80 100 1.0 -40 to 125

NCP15XF101p0SRC 100 3250 ±3% 3.10 100 1.0 -40 to 125

NCP15XF151p0SRC 150 3250 ±3% 2.50 100 1.0 -40 to 125

NCP15XM221p0SRC 220 3500 ±3% 2.10 100 1.0 -40 to 125

NCP15XM331p0SRC 330 3500 ±3% 1.70 100 1.0 -40 to 125

NCP15XQ471p0SRC 470 3650 ±2% 1.40 100 1.0 -40 to 125

NCP15XQ681p0SRC 680 3650 ±3% 1.20 100 1.0 -40 to 125

NCP15XQ102p0SRC 1.0k 3650 ±2% 1.00 100 1.0 -40 to 125

NCP15XW152p0SRC 1.5k 3950 ±3% 0.81 100 1.0 -40 to 125

NCP15XW222p0SRC 2.2k 3950 ±3% 0.67 100 1.0 -40 to 125

NCP15XW332p0SRC 3.3k 3950 ±3% 0.55 100 1.0 -40 to 125

NCP15XM472p0SRC 4.7k 3500 ±2% 0.46 100 1.0 -40 to 125

NCP15XW682p0SRC 6.8k 3950 ±3% 0.38 100 1.0 -40 to 125

NCP15XH103p0SRC 10k 3380 ±1% 0.31 100 1.0 -40 to 125

NCP15XV103p0SRC 10k 3900 ±3% 0.31 100 1.0 -40 to 125

NCP15XW153p0SRC 15k 3950 ±3% 0.25 100 1.0 -40 to 125

NCP15WL223p0SRC 22k 4485 ±1% 0.21 100 1.0 -40 to 125

NCP15XW223p0SRC 22k 3950 ±3% 0.21 100 1.0 -40 to 125

NCP15WB333p0SRC 33k 4050 ±3% 0.17 100 1.0 -40 to 125

NCP15WL333p0SRC 33k 4485 ±1% 0.17 100 1.0 -40 to 125

NCP15WB473p0SRC 47k 4050 ±1% 0.14 100 1.0 -40 to 125

NCP15WL473p0SRC 47k 4485 ±1% 0.14 100 1.0 -40 to 125

NCP15WD683p0SRC 68k 4150 ±3% 0.12 100 1.0 -40 to 125

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

9

1

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Part Number Resistance

(25°C)

(ohm)

B-Constant

(25-50°C)

(K)

Permissive Operating

Current (25°C)

(mA)

Rated Electric

Power (25°C)

(mW)

Typical Dissipation

Constant (25°C)

(mW/°C)

Operating

Temperature Range

(°C)

Continued from the preceding page.

NCP15WL683p0SRC 68k 4485 ±1% 0.12 100 1.0 -40 to 125

NCP15WF104p0SRC 100k 4250 ±1% 0.10 100 1.0 -40 to 125

NCP15WL104p0SRC 100k 4485 ±1% 0.10 100 1.0 -40 to 125

NCP15WL154p0SRC 150k 4485 ±1% 0.08 100 1.0 -40 to 125

NCP15WM154p0SRC 150k 4500 ±3% 0.08 100 1.0 -40 to 125

NCP15WM224p0SRC 220k 4500 ±3% 0.06 100 1.0 -40 to 125

NCP15WM474p0SRC 470k 4500 ±3% 0.04 100 1.0 -40 to 125

A blank column is filled with resistance tolerance codes (J: ±5%). Please contact us for other tolerances.

Resistance tolerance ±1% is also available for the following type.

10k ohm: NCP15XH103F0SRC

47k ohm: NCP15WB473F0SRC

100k ohm: NCP15WF104F0SRC

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

10

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

NTC/PTC Thermistors for Automotive

NTC Thermistor Chip Type 0603 (1608) Size (Meet AEC-Q200rev.C)

0402/0603 sized Chip NTC Thermistors have Ni barrier

termination and provide excellent solderability and

offer high stability in environment by unique inner

construction.

■ Features

1. NCP18xx0S series can meet AEC-Q200rev.C requirements

2. Excellent solderability and high stability in environment

3. Excellent long time aging stability

4. High accuracy in resistance and B-constant

5. Flow/Reflow soldering possible

6. Lead is not contained in the product

7. NCP18 series are recognized by UL

(UL1434, File No.E137188 Vol.2, Sec.2 ).

■ Applications

1. Car audio, car navigation

2. Various engine control units

3. Circuits for ETC equipment

4. Various motor driving circuits

5. Temperature compensation for various circuits

Electrode

(Ag System + Ni Plating + Sn Plating)

0.2—0.6 0.2—0.6

1.6±0.15

(in mm)

0.8±0.15

Part Number Resistance

(25°C)

(ohm)

B-Constant

(25-50°C)

(K)

Permissive Operating

Current (25°C)

(mA)

Rated Electric

Power (25°C)

(mW)

Typical Dissipation

Constant (25°C)

(mW/°C)

Operating

Temperature Range

(°C)

NCP18XF101p0SRB 100 3250 ±3% 3.10 100 1.0 -40 to 125

NCP18XF151p0SRB 150 3250 ±3% 2.50 100 1.0 -40 to 125

NCP18XM221p0SRB 220 3500 ±3% 2.10 100 1.0 -40 to 125

NCP18XM331p0SRB 330 3500 ±3% 1.70 100 1.0 -40 to 125

NCP18XQ471p0SRB 470 3650 ±2% 1.40 100 1.0 -40 to 125

NCP18XQ681p0SRB 680 3650 ±3% 1.20 100 1.0 -40 to 125

NCP18XQ102p0SRB 1.0k 3650 ±2% 1.00 100 1.0 -40 to 125

NCP18XW152p0SRB 1.5k 3950 ±3% 0.81 100 1.0 -40 to 125

NCP18XW222p0SRB 2.2k 3950 ±3% 0.67 100 1.0 -40 to 125

NCP18XW332p0SRB 3.3k 3950 ±3% 0.55 100 1.0 -40 to 125

NCP18XM472p0SRB 4.7k 3500 ±2% 0.46 100 1.0 -40 to 125

NCP18XW682p0SRB 6.8k 3950 ±3% 0.38 100 1.0 -40 to 125

NCP18XH103p0SRB 10k 3380 ±1% 0.31 100 1.0 -40 to 125

NCP18XW153p0SRB 15k 3950 ±3% 0.25 100 1.0 -40 to 125

NCP18XW223p0SRB 22k 3950 ±3% 0.21 100 1.0 -40 to 125

NCP18WB333p0SRB 33k 4050 ±3% 0.17 100 1.0 -40 to 125

NCP18WB473p1SRB 47k 4050 ±1.5% 0.14 100 1.0 -40 to 125

NCP18WB473p0SRB 47k 4050 ±2% 0.14 100 1.0 -40 to 125

NCP18WD683p0SRB 68k 4150 ±3% 0.12 100 1.0 -40 to 125

NCP18WF104p3SRB 100k 4200 ±1% 0.10 100 1.0 -40 to 125

NCP18WF104p0SRB 100k 4250 ±2% 0.10 100 1.0 -40 to 125

NCP18WM154p0SRB 150k 4500 ±3% 0.08 100 1.0 -40 to 125

NCP18WM224p0SRB 220k 4500 ±3% 0.06 100 1.0 -40 to 125

NCP18WM474p0SRB 470k 4500 ±3% 0.04 100 1.0 -40 to 125

A blank column is filled with resistance tolerance codes (J: ±5%). Please contact us for other tolerances.

Resistance tolerance ±1% is also available for the following type.

10k ohm: NCP18XH103F0SRB

47k ohm: NCP18WB473F1SRB

100k ohm: NCP18WF104F3SRB

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For NTC Thermistors Chip Type Standard Land Pattern Dimensions

11

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Chip

Land

Solder Resist

b a

c

(in mm)

Part Number Soldering

Methods c

NCP15 Reflow Soldering 0.5

NCP18 Flow Soldering

Reflow Soldering

0.6-0.8

b

0.4-0.5

0.8-0.9

a

0.4

0.6-1.0

0.6-0.80.6-0.70.6-0.8

Chip (LgW)

Dimensions (mm)

1.0g0.5

1.6g0.8

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

1

Continued on the following page.

355.823

273.975

213.003

166.943

131.997

105.318

84.670

68.628

55.981

45.859

37.819

31.396

26.211

22.000

18.560

15.735

13.403

11.462

9.842

8.488

7.348

6.399

5.595

4.896

4.299

3.795

3.360

2.983

2.656

2.367

2.116

1.901

1.712

1.543

NCPppXC220

22Ω

533.734

410.962

319.504

250.415

197.996

157.978

127.005

102.942

83.972

68.789

56.728

47.094

39.317

33.000

27.840

23.603

20.104

17.193

14.763

12.732

11.022

9.598

8.392

7.345

6.448

5.692

5.040

4.474

3.983

3.551

3.173

2.851

2.568

2.314

NCPppXC330

33Ω

760.166

585.310

455.051

356.652

281.994

224.998

180.886

146.614

119.596

97.972

80.794

67.073

55.997

47.000

39.651

33.616

28.633

24.487

21.026

18.133

15.698

13.670

11.952

10.461

9.184

8.107

7.179

6.373

5.673

5.057

4.520

4.060

3.657

3.296

NCPppXC470

47Ω

1099.815

846.832

658.372

516.007

407.991

325.529

261.707

212.123

173.033

141.747

116.894

97.042

81.016

68.000

57.368

48.636

41.426

35.428

30.421

26.235

22.712

19.778

17.293

15.134

13.288

11.729

10.386

9.220

8.208

7.317

6.539

5.874

5.291

4.768

NCPppXC680

68Ω

1824.175

1390.685

1070.653

831.138

650.960

514.441

409.700

328.877

265.759

215.785

176.395

145.161

120.152

100.000

83.669

70.361

59.456

50.470

43.029

36.830

31.649

27.364

23.756

20.651

18.011

15.800

13.908

12.263

10.844

9.622

8.563

7.648

6.850

6.162

NCPppXF101

100Ω

2736.262

2086.028

1605.979

1246.708

976.440

771.661

614.550

493.315

398.639

323.677

264.592

217.742

180.228

150.000

125.503

105.541

89.184

75.705

64.543

55.246

47.473

41.045

35.634

30.976

27.016

23.700

20.862

18.394

16.265

14.434

12.844

11.472

10.275

9.243

NCPppXF151

150Ω

4947.904

3703.755

2798.873

2135.887

1645.037

1278.034

1000.620

789.612

627.752

502.474

405.010

328.480

268.044

220.000

181.576

150.668

125.681

105.336

88.717

75.059

63.777

54.415

46.631

40.115

34.637

30.013

26.110

22.790

19.957

17.541

15.453

13.663

12.114

10.778

NCPppXM221

220Ω

7421.856

5555.632

4198.309

3203.831

2467.555

1917.051

1500.930

1184.418

941.628

753.711

607.514

492.720

402.066

330.000

272.365

226.002

188.521

158.004

133.076

112.588

95.666

81.622

69.946

60.172

51.955

45.019

39.165

34.186

29.935

26.312

23.180

20.494

18.171

16.168

NCPppXM331

330Ω

17104.854

12685.248

9505.855

7193.219

5493.436

4229.599

3283.675

2568.411

2024.158

1606.275

1283.691

1032.245

835.351

680.000

556.733

458.287

379.320

315.504

263.749

221.579

186.998

158.499

134.960

115.383

99.029

85.356

73.839

64.140

55.905

48.888

42.918

37.795

33.409

29.618

NCPppXQ681

680Ω

25.154

18.655

13.979

10.578

8.079

6.220

4.829

3.777

2.977

2.362

1.888

1.518

1.229

1.000

0.819

0.674

0.558

0.464

0.388

0.326

0.275

0.233

0.199

0.170

0.146

0.126

0.109

0.094

0.082

0.072

0.063

0.056

0.049

0.044

NCPppXQ102

1.0kΩ

51.791

37.172

27.005

19.843

14.728

11.044

8.362

6.389

4.922

3.825

2.994

2.361

1.876

1.500

1.207

0.978

0.797

0.653

0.538

0.446

0.371

0.311

0.261

0.221

0.187

0.160

0.137

0.117

0.101

0.088

0.076

0.067

0.058

0.051

NCPppXW152

1.5kΩ

11822.473

8767.745

6570.224

4971.784

3796.933

2923.400

2269.599

1775.225

1399.050

1110.220

887.257

713.463

577.375

470.000

384.800

316.757

262.177

218.069

182.297

153.150

129.249

109.551

93.281

79.750

68.446

58.996

51.036

44.332

38.640

33.790

29.664

26.123

23.091

20.472

NCPppXQ471

470Ω

3100K 3100K 3100K 3100K 3250K 3250K

3500K 3500K 3650K 3650K 3950K3650K

Resistance (Ω) Resistance (Ω) Resistance (Ω) Resistance (Ω) Resistance (Ω) Resistance (Ω)

Resistance (Ω) Resistance (Ω) Resistance (Ω) Resistance (kΩ) Resistance (kΩ)Resistance (Ω)

Detailed Resistance-Temperature Tables are downloadable from the following URL.

http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

Temp. (°C)

B-Constant

Resistance

Part Number

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

Temp. (°C)

B-Constant

Resistance

Part Number

For NTC Thermistors Chip Type Temperature Characteristics (Center Value)

12

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

2

Continued from the preceding page.

Continued on the following page.

517.912

371.724

270.048

198.426

147.278

110.439

83.617

63.888

49.221

38.245

29.936

23.613

18.756

15.000

12.074

9.780

7.969

6.531

5.382

4.459

3.713

3.108

2.613

2.208

1.873

1.597

1.367

1.174

1.013

0.878

0.763

0.665

0.582

0.511

NCPppXW153

15kΩ

759.605

545.196

396.070

291.025

216.008

161.977

122.638

93.702

72.191

56.093

43.907

34.633

27.509

22.000

17.709

14.344

11.688

9.578

7.894

6.540

5.446

4.559

3.832

3.239

2.748

2.342

2.004

1.722

1.486

1.287

1.119

0.975

0.854

0.750

NCPppXW223

22kΩ

1073.436

753.900

535.073

383.590

277.643

202.813

149.462

111.082

83.233

62.858

47.831

36.664

28.304

22.000

17.214

13.557

10.744

8.566

6.871

5.543

4.497

3.669

3.009

2.481

2.056

1.713

1.434

1.206

1.019

0.866

0.739

0.633

0.545

0.471

NCPppWL223

22kΩ

1227.263

874.449

630.851

460.457

339.797

253.363

190.766

144.964

111.087

85.842

66.861

52.470

41.471

33.000

26.430

21.298

17.266

14.076

11.538

9.506

7.870

6.549

5.475

4.595

3.874

3.282

2.789

2.379

2.038

1.751

1.509

1.306

1.134

0.987

NCPppWB333

33kΩ

1610.154

1130.850

802.609

575.385

416.464

304.219

224.193

166.623

124.850

94.287

71.747

54.996

42.455

33.000

25.822

20.335

16.115

12.849

10.306

8.314

6.746

5.503

4.513

3.721

3.084

2.569

2.151

1.809

1.529

1.299

1.108

0.949

0.817

0.707

NCPppWL333

33kΩ

1747.920

1245.428

898.485

655.802

483.954

360.850

271.697

206.463

158.214

122.259

95.227

74.730

59.065

47.000

37.643

30.334

24.591

20.048

16.433

13.539

11.209

9.328

7.798

6.544

5.518

4.674

3.972

3.388

2.902

2.494

2.150

1.860

1.615

1.406

NCPppWB473

47kΩ

195.652

148.171

113.347

87.559

68.237

53.650

42.506

33.892

27.219

22.021

17.926

14.674

12.081

10.000

8.315

6.948

5.834

4.917

4.161

3.535

3.014

2.586

2.228

1.925

1.669

1.452

1.268

1.110

0.974

0.858

0.758

0.672

0.596

0.531

NCPppXH103

10kΩ

328.996

237.387

173.185

127.773

95.327

71.746

54.564

41.813

32.330

25.194

19.785

15.651

12.468

10.000

8.072

6.556

5.356

4.401

3.635

3.019

2.521

2.115

1.781

1.509

1.284

1.097

0.941

0.810

0.701

0.608

0.530

0.463

0.406

0.358

NCPppXV103

10kΩ

3950K 3950K 4485K 4050K 4485K 4050K

3380K 3900K

Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)

Resistance (kΩ) Resistance (kΩ)

Detailed Resistance-Temperature Tables are downloadable from the following URL.

http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

Temp. (°C)

B-Constant

Resistance

Part Number

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

Temp. (°C)

B-Constant

Resistance

Part Number

75.961

54.520

39.607

29.103

21.601

16.198

12.264

9.370

7.219

5.609

4.391

3.463

2.751

2.200

1.771

1.434

1.169

0.958

0.789

0.654

0.545

0.456

0.383

0.324

0.275

0.234

0.200

0.172

0.149

0.129

0.112

0.098

0.085

0.075

NCPppXW222

2.2kΩ

113.941

81.779

59.411

43.654

32.401

24.297

18.396

14.055

10.829

8.414

6.586

5.195

4.126

3.300

2.656

2.152

1.753

1.437

1.184

0.981

0.817

0.684

0.575

0.486

0.412

0.351

0.301

0.258

0.223

0.193

0.168

0.146

0.128

0.113

NCPppXW332

3.3kΩ

105.705

79.126

59.794

45.630

35.144

27.303

21.377

16.869

13.411

10.735

8.653

7.018

5.726

4.700

3.879

3.219

2.685

2.250

1.895

1.604

1.363

1.163

0.996

0.857

0.740

0.641

0.558

0.487

0.426

0.375

0.330

0.292

0.259

0.230

NCPppXM472

4.7kΩ

234.787

168.515

122.422

89.953

66.766

50.066

37.906

28.963

22.313

17.338

13.571

10.705

8.503

6.800

5.474

4.434

3.613

2.961

2.440

2.022

1.683

1.409

1.185

1.001

0.849

0.724

0.620

0.532

0.459

0.398

0.346

0.302

0.264

0.232

NCPppXW682

6.8kΩ

3950K 3950K 3500K 3950K

Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)

For NTC Thermistors Chip Type Temperature Characteristics (Center Value)

13

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

3

Continued from the preceding page.

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

Temp. (°C)

B-Constant

Resistance

Part Number

4879.254

3426.818

2432.149

1743.590

1262.012

921.875

679.373

504.919

378.333

285.717

217.414

166.654

128.653

100.000

78.247

61.622

48.835

38.937

31.231

25.195

20.441

16.675

13.677

11.277

9.346

7.785

6.517

5.482

4.634

3.935

3.357

2.877

2.476

2.141

NCPppWL104

100kΩ

7318.881

5140.228

3648.224

2615.385

1893.018

1382.813

1019.059

757.379

567.499

428.575

326.121

249.981

192.979

150.000

117.370

92.433

73.252

58.406

46.846

37.793

30.661

25.013

20.516

16.916

14.019

11.678

9.776

8.223

6.951

5.902

5.035

4.315

3.714

3.211

NCPppWL154

150kΩ

7899.466

5466.118

3834.499

2720.523

1951.216

1415.565

1036.984

767.079

572.667

431.264

327.405

250.538

193.166

150.000

117.281

92.293

73.090

58.240

46.665

37.605

30.453

24.804

20.293

16.679

13.776

11.428

9.520

7.966

6.688

5.639

4.772

4.052

3.454

2.955

NCPppWM154

150kΩ

11585.884

8016.973

5623.931

3990.100

2861.784

2076.162

1520.909

1125.049

839.912

632.521

480.194

367.455

283.310

220.000

172.012

135.364

107.198

85.419

68.441

55.153

44.665

36.379

29.763

24.462

20.205

16.761

13.962

11.684

9.809

8.270

6.998

5.942

5.067

4.334

NCPppWM224

220kΩ

24751.661

17127.169

12014.762

8524.305

6113.811

4435.437

3249.216

2403.515

1794.358

1351.294

1025.870

785.018

605.252

470.000

367.480

289.186

229.014

182.485

146.215

117.828

95.420

77.718

63.584

52.260

43.166

35.808

29.828

24.961

20.955

17.668

14.951

12.695

10.824

9.259

NCPppWM474

470kΩ

4485K 4485K

4500K 4485K 4500K

Resistance (kΩ) Resistance (kΩ)

Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

Temp. (°C)

B-Constant

Resistance

Part Number

2293.249

1610.605

1143.110

819.487

593.146

433.281

319.305

237.312

177.816

134.287

102.184

78.327

60.467

47.000

36.776

28.962

22.952

18.301

14.679

11.842

9.607

7.837

6.428

5.300

4.393

3.659

3.063

2.577

2.178

1.849

1.578

1.352

1.164

1.006

NCPppWL473

47kΩ

3317.893

2330.237

1653.862

1185.641

858.168

626.875

461.974

343.345

257.266

194.287

147.841

113.325

87.484

68.000

53.208

41.903

33.208

26.477

21.237

17.133

13.900

11.339

9.300

7.668

6.356

5.294

4.432

3.728

3.151

2.676

2.283

1.956

1.684

1.456

NCPppWL683

68kΩ

4397.119

3088.599

2197.225

1581.881

1151.037

846.579

628.988

471.632

357.012

272.500

209.710

162.651

127.080

100.000

79.222

63.167

50.677

40.904

33.195

27.091

22.224

18.323

15.184

12.635

10.566

8.873

7.481

6.337

5.384

4.594

3.934

3.380

2.916

2.522

NCPppWF104

100kΩ

2735.359

1937.391

1389.345

1008.014

738.978

547.456

409.600

309.217

235.606

180.980

140.139

109.344

85.929

68.000

54.167

43.421

35.016

28.406

23.166

18.997

15.657

12.967

10.794

9.021

7.575

6.387

5.407

4.598

3.922

3.359

2.887

2.489

2.155

1.870

NCPppWD683

68kΩ

4485K 4485K 4250K ∗4150K

Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)Resistance (kΩ)

∗ B-Constant of NCP18WF104F1SRB is 4200K. Please contact us for the detail data.

Detailed Resistance - Temperature Tables are downloadable from the following URL.

http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en

For NTC Thermistors Chip Type Temperature Characteristics (Center Value)

14

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

No.

AEC-Q200 Test Item

Specifications AEC-Q200 Test Methods

-

Pre-and Post-

Stress

Electrical Test

1

(*1)

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

High Temperature

Exposure

(Storage)

2125±3 °C in air for 1000 hours.

Measurement at 24±2 hours after test condition.

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Temperature

Cycling

3

Perform the 1000 cycles according to the four heat treatments

listed in the following table.

Measurement at 24±2 hours after test condition.

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Moisture

Resistance

4

Apply the 24 hours heat (25 to 65 °C) and humidity (80 to 98%)

treatment shown below, 10 consecutive times.

Measurement at 24±2 hours after test condition.

(*2)

•Resistance(R25) change should be less than ±10%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Biased Humidity5 85±2 °C, 85%RH in air for 1000 hours

with Permissive Operating Current.

Measurement at 24±2 hours after test condition.

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Operational Life6 125±3 °C in air for 1000 hours

with Permissive Operating Current.

Measurement at 24±2 hours after test condition.

No defects of abnormalities.

External Visual7 Visual Inspection.

Within the specified dimensions.

Physical

Dimension

8Using calipers

N/A

Terminal Strengh

(Leaded)

9

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Resistance to

Solvents

10 Per MIL-STD-202 Method 215

Solvent 1: 1 part (by volume) of isopropyl alcohol

3 part (by volume) of mineral spirits.

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Mechanical Shock11 Per MIL-STD-202 Method 213 Test Condition F

1500g's, 0.5ms, In 3 directions perpendicularly intersecting

each other (total 18 times).

(*1)

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Vibration12

Simple harmonic motion between 10Hz to 2.0k Hz and back to

10 Hz of max. amplitude 1.5mm for 20 minutes. This motion

should be applied for 12 times in each of 3 mutually

perpendicular directions (total of 36 times).

(*1)

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Resistance to

Soldering Heat

13 Per MIL-STD-202 Method 210

Test Condition B, 260 °C for 10 +/-1 seconds

• The Test Condition specification (*1,*2) is applied to the follow P/N.

P/N: NCP15XH103**SR*, NCP15WL233**SR*, NCP15WL333**SR*, NCP15WL473**SR*, NCP15WL683**SR*, NCP15WL104**SR*,

NCP15WL154**SR*, NCP15WB473**SR*, NCP15WF104**SR*, NCP18XH103**SR*,

(*1) Resistance(R25) change should be less than 1%

B-constant(B25/50) change should be less than 1%

(*2) Resisitance(R25) change should be less than 5%

B-constant(B25/50) change should be less than 1%

Step

Temp. (deg.C)

Time (min.) -55+0/-3

15±3

Room Temp.

1125+3/-0

15±3

Room Temp.

1

1234

Humidity

90 to 98% Humidity

80 to 98% Humidity

90 to 98% Humidity

80 to 98% Humidity

90 to 98%

One cycle 24 hours

Temperature(deg.C)

Hours

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Initial measurement

+10deg.C

-2

Continued on the following page.

For NTC Thermistors Chip Type Specifications and Test Methods

15

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

No.

AEC-Q200 Test Item

Specifications AEC-Q200 Test Methods

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Thermal Shock14

Perform the 300 cycles according to the two heat treatments

listed in the following table. (Maximum transfer time is 20

seconds.)

Measurement at 24±2 hours after test condition.

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

ESD15 Per AEC-Q200-004

Minimum 95% of the whole electrode surface

should be covered with solder.

Solderability16 Per J-STD-002

SMD b) Method B @ 215 °C category 3.

Within the specified tolerance.

Electrical

Characterization

17 Resistance at 25 °C.

B-constant (B25-50)

N/A

Flammability18

(*1)

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Board Flex19

Per AEC-Q200-005

Bend the board 2.0mm for 60 seconds.

Use the follow land size.

(*1)

•Resistance(R25) change should be less than ±5%.

•B-constant(B25/50) change should be less than ±2%.

•No visible damage.

Terminal Strengh

(SMD)

20

Per AEC-Q200-006

Apply an *18N force to the side of device for 60 seconds.

Use follow land size.

*5N (NCP15****0SRC)

• The Test Condition specification (*1,*2) is applied to the follow P/N.

P/N: NCP15XH103**SR*, NCP15WL233**SR*, NCP15WL333**SR*, NCP15WL473**SR*, NCP15WL683**SR*, NCP15WL104**SR*,

NCP15WL154**SR*, NCP15WB473**SR*, NCP15WF104**SR*, NCP18XH103**SR*,

(*1) Resistance(R25) change should be less than 1%

B-constant(B25/50) change should be less than 1%

(*2) Resisitance(R25) change should be less than 5%

B-constant(B25/50) change should be less than 1%

Continued from the preceding page.

Step

Temp. (°C)

Time (min.) -55+0/-3

15±3 125+3/-0

15±3

1 2

Type

NCP15****0SRC

NCP18****0SRB 0.4

0.6 1.2

1.8 0.5

0.6

(in mm)

a b c

ac

b

Type

NCP15****0SRC

NCP18****0SRB 0.4

1.0 1.5

3.0 0.5

1.2

(in mm)

a b c

ac

b

For NTC Thermistors Chip Type Specifications and Test Methods

16

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For NTC Thermistors Chip Type !Caution/Notice

17

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ !Caution (Storage and Operating Condition)

This product is designed for application in an

ordinary environment (normal room temperature,

humidity and atmospheric pressure).

Do not use under the following conditions because

all these factors can deteriorate the product

characteristics or cause failures and burn-out.

1. Corrosive gas or deoxidizing gas

(Chlorine gas, Hydrogen sulfide gas, Ammonia gas,

Sulfuric acid gas, Nitric oxide gas, etc.)

2. Volatile or flammable gas

3. Dusty conditions

4. Under vacuum, or under high or low-pressure

5. Wet or humid locations

6. Places with salt water, oils, chemical liquids or

organic solvents

7. Strong vibrations

8. Other places where similar hazardous conditions

exist

■ !Caution (Other)

Be sure to provide an appropriate fail-safe function

on your product to prevent secondary damages that may be

caused by the abnormal function or the failure of our

product.

■ Notice (Storage and Operating Condition)

To keep solderability of product from declining, the

following storage condition is recommended.

1. Storage condition:

Temperature -10 to +40 degrees C

Humidity less than 75%RH (not dewing condition)

2. Storage term:

Use this product within 6 months after delivery by

first-in and first-out stocking system.

3. Handling after unpacking:

After unpacking, reseal product promptly or

store it in a sealed container with a drying agent.

4. Storage place:

Do not store this product in corrosive gas

(Sulfuric acid gas, Chlorine gas, etc.) or in direct

sunlight.

■ Notice (Rating)

Use this product within the specified temperature

range.

Higher temperature may cause deterioration of the

characteristics or the material quality of this

product.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

1

Allowable Reflow Soldering Temperature and Time Standard Soldering Conditions

Locate this

product

horizontal to the

direction in

which stress

acts.

Keep this product on the

PC Board away from the

Separation Line.

Worst ← A-B-C-D → Better

Component Direction

Mounting Close to Board Separation Line

A

B

D

C

Perforation

Holes

Slit

1. Mounting Position

2. Reflow Soldering Conditions

Choose a mounting position that minimizes the stress

imposed on the chip during flexing or bending of the

board.

Continued on the following page.

Time (sec.)

Temperature (°C)

280

270

260

250

240

230

220

2100 1109020 30 40 50 60 70 1008010

Temperature (°C)

Preheating (in air)

Soldering

Gradual cooling

(in air)

300

200

100

01-2 min.

20 sec. max.

Preheating: 160±10°C, 1-2 minutes

Soldering: 230-270°C, 20 seconds max.

Time (sec.)

Temperature (°C)

280

270

260

250

240

230

220 0 9020 30 40 50 60 70 8010

Temperature (°C)

Preheating (in air)

Soldering

Gradual cooling

(in air)

300

200

100

01-2 min.

20 sec. max.

Preheating: 160±10°C, 1-2 minutes

Soldering: 240-270°C, 20 seconds max.

(NCP18 Series)

(NCP15 Series)

Time (sec.)

Temperature (°C)

280

270

260

250

240

230

220

2100 10 20 30

Preheating (in air)

Soldering

Gradual cooling

(in air)

300

200

100

01-2 min.

10 sec. max.

Preheating: 160±10°C, 1-2 minutes

Soldering: 230-260°C, 10 seconds max.

3. Flow Soldering Conditions

(NCP18 Series)

Allowable Flow Soldering Temperature and Time Standard Soldering Conditions

■ Notice (Soldering and Mounting)

For NTC Thermistors Chip Type !Caution/Notice

18

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

2

For removing the flux after soldering, observe the

following points in order to avoid deterioration of the

characteristics or any change of the external electrodes'

quality.

(1) Solder and Paste

(a) Reflow Soldering: NCP15/NCP18 Series

Use RA/RMA type or equivalent type of solder paste.

For your reference, we are using the solder paste

below for any internal tests of this product.

•RMA9086 90-4-M20 (Sn:Pb=63wt%:37wt%)

(Manufactured by Alpha Metals Japan Ltd.)

•M705-221BM5-42-11

(Sn:Ag:Cu=96.5wt%:3.0wt%:0.5wt%)

(Manufactured by Senju Metal Industry Co., Ltd.)

(b) Flow Soldering: NCP18 Series

We are using the solder paste below for any internal

tests of this product.

•Sn:Pb=63wt%:37wt%

•Sn:Ag:Cu=96.5wt%:3.0wt%:0.5wt%

(2) Flux

Use Rosin-based flux.

Do not use strong acidic flux (with halide content

exceeding 0.2wt%)

NCP15 NCP18

Continued from the preceding page.

4. Solder and Flux

5. Cleaning Conditions

After cleaning, promptly dry this product.

6. Drying

Isopropyl Alcohol

Less than 5 minutes at

room temp. or less than

2 minutes at 40°C max.

Less than 5 minutes

20W/r Frequency of 28

to 40kHz.

Isopropyl Alcohol

Less than 5 minutes at

room temp. or less than

2 minutes at 40°C max.

Less than 1

minute

20W/

r

Frequency of

several 10 to 100kHz.

Solvent

Dipping Cleaning

Ultrasonic Cleaning

Thin or insufficient adhesive may result in loose

component contact with land during flow soldering.

Low viscosity adhesive causes chips to slip after

mounting.

NCP15

NCP18

100µm

150µm

1/3EVTVE

0.2mmVTVE

Part Number The Solder Paste Thickness T

Reference: Optimum Solder Amount

T

E

Electrode

Solder Solder

The amount of solder is critical. Standard height of fillet is

shown in the table below.

Too much soldering may cause mechanical stress,

resulting in cracking, mechanical and/or electronic

damage.

8. Adhesive Application and Curing

7. Printing Conditions of Solder Paste

For NTC Thermistors Chip Type !Caution/Notice

19

2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Handling)

The ceramic of this product is fragile, and care must

be taken to not load an excessive press-force, or to not

give a shock at handling.

Such forces may cause cracking or chipping.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

20

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

NTC/PTC Thermistors for Automotive

NTC Thermistor Lead Type for Temperature Sensor

Solder Plated Copper Ply Wire

ø0.4±0.03

31±1

2.5±1.0

6.0 max.

3.0 max. (*3.3 max.) 1.8 max. (*2.5 max.)

Epoxy Resin

(in mm)

* It applies to NTSS0XM202, NTSS0WB203

and NTSS0WC303 Type.

■ Temperature Tolerance - Temperature Characteristics

Resistance tolerance:1% B - Constant tolerance:1%

Temperature (°C)

Temperature Tolerance (±°C)

0

1.0

2.0

3.0

-50 0 50 100 150

Resistance tolerance:1% B - Constant tolerance:0.5%

Temperature (°C)

Temperature Tolerance (±°C)

0

1.0

2.0

3.0

-50 0 50 100 150

This product is a sensor type NTC Thermistor to be

useful in the normal temperature range developed by

the unique ceramic technology and the automatic

assembly.

■ Features

1. High-accuracy of B-Constant tolerance:+/-0.5%

+/-1% of resistance and +/-0.5% of B-Constant

is realized due to technical advantages of the

material and manufacturing process.

2. Quick response

This product provides faster response time due to

its smaller size.

3. Taping type is available.

4. Strong lead strength

Original lead-wiring technique assures reliable

connection. It can be formed and bent flexibly

according to the mounting condition.

■ Applications

1. Car audio, car navigation

2. Various engine control units

3. Circuits for ETC equipment

4. Various motor driving circuits

5. Temperature compensation for various circuits

Part Number Resistance

(25°C)

(k ohm)

B-Constant

(25-50°C)

(K)

Permissive Operating

Current (25°C)

(mA)

Rated Electric

Power (25°C)

(mW)

Typical Dissipation

Constant (25°C)

(mW/°C)

Thermal Time

Constant

(25°C)(s)

Operating

Temperature Range

(°C)

NTSS0XM202pE1B0 2.0 3500 ±0.5% 1.05 21 2.1 7 -40 to 125

NTSS0XR502pE1B0 5.0 3700 ±1% 0.68 15 1.5 7 -40 to 125

NTSS0XH103pE1B0 10 3380 ±0.5% 0.38 15 1.5 7 -40 to 125

NTSS0XV103pE1B0 10 3900 ±0.5% 0.46 15 1.5 7 -40 to 125

NTSS0WB203pE1B0 20 4050 ±1% 0.31 21 2.1 7 -40 to 125

NTSS0WC303pE1B0 30 4100 ±1% 0.26 21 2.1 7 -40 to 125

NTSS0WD503pE1B0 50 4150 ±1% 0.20 15 1.5 7 -40 to 125

NTSS0WF104pE1B0 100 4250 ±1% 0.14 15 1.5 7 -40 to 125

A blank column is filled with resistance tolerance codes (F: ±1%, E: ±3%).

Taping type of part numbers with "N6A0" is available (Lead spacing=5mm).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

Y40

Y35

Y30

Y25

Y20

Y15

Y10

Y5

0

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

80

85

90

95

100

105

110

115

120

125

44.657

33.505

25.388

19.402

14.961

11.644

9.133

7.198

5.716

4.571

3.682

2.987

2.437

2.000

1.651

1.371

1.143

0.958

0.807

0.683

0.582

0.497

0.426

0.367

0.318

0.276

0.240

0.210

0.183

0.161

0.142

0.125

0.111

0.099

123.484

92.295

69.614

52.860

40.480

31.275

24.339

19.154

15.148

11.964

9.520

7.624

6.160

5.000

4.082

3.354

2.773

2.299

1.914

1.607

1.356

1.149

0.978

0.834

0.714

0.612

0.527

0.456

0.396

0.345

0.302

0.264

0.232

0.205

195.652

148.171

113.347

87.559

68.237

53.650

42.506

33.892

27.219

22.021

17.926

14.674

12.081

10.000

8.315

6.948

5.834

4.917

4.161

3.535

3.014

2.586

2.228

1.925

1.669

1.452

1.268

1.110

0.974

0.858

0.758

0.671

0.596

0.531

347.808

248.591

179.973

131.832

97.679

73.119

55.301

42.257

32.582

25.324

19.847

15.679

12.478

10.000

8.068

6.552

5.353

4.399

3.635

3.020

2.521

2.115

1.783

1.510

1.284

1.096

0.939

0.808

0.698

0.605

0.527

0.460

0.403

0.354

NTSppXM202 NTSppXR502 NTSppXH103 NTSppXV103

Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)

1

733.007

524.831

380.184

277.845

205.260

153.642

116.016

88.125

67.522

52.168

40.617

31.847

25.151

20.000

16.014

12.902

10.457

8.527

6.993

5.771

4.789

3.992

3.343

2.809

2.376

2.020

1.724

1.476

1.264

1.085

0.935

0.812

0.708

0.617

1149.500

819.651

591.391

430.529

316.870

236.337

177.842

134.630

102.816

79.183

61.460

48.045

37.834

30.000

23.955

19.249

15.560

12.657

10.354

8.525

7.058

5.869

4.905

4.113

3.472

2.945

2.509

2.143

1.832

1.571

1.350

1.171

1.019

0.886

1948.575

1387.289

999.456

728.895

537.039

399.167

299.469

226.186

172.393

132.857

103.089

80.430

63.201

50.000

39.825

31.918

25.733

20.877

17.034

13.929

11.439

9.485

7.906

6.614

5.558

4.686

3.967

3.373

2.878

2.465

2.118

1.828

1.583

1.374

4256.752

3005.888

2148.514

1555.020

1137.312

839.314

625.338

469.127

355.224

272.045

209.803

162.713

127.117

100.000

79.215

63.150

50.649

40.885

33.195

27.014

22.079

18.226

15.124

2.598

10.542

8.852

7.463

6.321

5.374

4.585

3.925

3.376

2.913

2.520

NTSppWB203 NTSppWC303 NTSppWD503 NTSppWF104

Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)

3500K 3700K 3380K 3900K 4050K 4100K 4150K 4250K

2.0kΩ5.0kΩ10kΩ10kΩ20kΩ30kΩ50kΩ100kΩ

Temp. (°C)

B-Constant

Resistance

Part Number

Detailed Resistance-Temperature Tables are downloadable from the following URL.

http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en

For NTC Thermistors Lead Type Temperature Characteristics (Center Value)

21

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

No. Item Rating Value Method of Examination

•Resistance (R25) fluctuation rate less than ±1%

•B-Constant (B25/50) fluctuation rate less than ±1%

•Resistance (R25) fluctuation rate less than ±2%

•B-Constant (B25/50) fluctuation rate less than ±1%

•Normal appearance

•Normal electrical characteristics on 500Vdc, 1 minute

•No visible damage

•Resistance (R25) change less than ±1%

•B-Constant (B25/50) change less than ±1%

No visible damage on lead wire

•No visible damage

•Resistance (R25) change less than ±1%

•B-Constant (B25/50) change less than ±1%

•Resistance (R25) change less than ±1%

•B-Constant (B25/50) change less than ±1%

•Resistance (R25) fluctuation rate less than ±2%

•B-Constant (B25/50) fluctuation rate less than ±1%

High Temp. Test 1

High Temp. Test 2

Low Temp. Test

Humidity Test

High Temp.

Pressure Test

Heat Shock Test

High Temp.

Continuous Load Test

Humidy Continuous

Load Test

Insulation

Break-down

Voltage

1

2

3

4

5

6

7

8

9

More than 90% of lead wire surface should be covered by

solder.

Resistance to

Soldering Heat

Solderability

11

12

Lead Wire Pull

Strength

Lead Wire

Bending Strength

13

14

Drop Test

Vibration

15

16

121±2°C, 2atm. in saturated vapor, leave for 2 +1/-0 hours

without loading

100±2°C in air, with Permissive Operating Current for 1000

+48/-0 hours

85±2°C, 85%RH in air, with Permissive Operating Current for

1000 +48/-0 hours

2mm length of coating resin from the top of thermistor is to be

dipped into beads of lead (Pb), and D.C 500V is applied to

circuit between beads of lead (Pb) and lead wire.

-55±3°C, 30 minutes in air

125±2°C, 30 minutes in air (1 cycle)

Continuous 1000 +4/-0 cycles without loading

125±3°C in air, for 1000 +48/-0 hours without loading

-40±3°C in air, for 1000 +48/-0 hours without loading

60±2°C, 90-95%RH in air, for 1000 +48/-0 hours without loading

150±2°C in air, for 500 +48/-0 hours without loading

•Normal appearance

•Resistance (R25) fluctuation rate less than ±1%

•B-Constant (B25/50) fluctuation rate less than ±1%

Solvent Proof10 Using Chlorine Washing Solvents, Boiling, 10 minutes

Supersonic, 10 minutes

Both lead wires are immersed into 350±10°C solder for 3.5±0.5

seconds or 260±5°C solder for 10±1 seconds according to

Fig-1. (solder <JIS Z 3282 H60A>)

Both lead wires are immersed into flux (25wt% colophony <JIS

K 5902> isopropyl alcohol <JIS K 8839>) for 5-10 seconds.

Then both lead wires are immersed into 235±5°C solder <JIS Z

3282 H60A> for 2±0.5 seconds. according to Fig-1.

One end of a lead wire should be fixed and 2.5N force for 10

seconds should be applied to the other lead wire as shown in

Fig-2.

One lead wire is held and 2.5N force is applied.

Then the body of NTC thermistor is bent 90° degrees and again

bent back to the initial position.

This sequence should be completed twice. See Fig-3.

NTC Thermistor should be dropped without any force onto

concrete floor from 1 meter height one time.

NTC Thermistor is to be fixed to the vibration test equipment.

Frequency: 10-2000-10Hz (20 minutes)

Max amplitude: 3.0mm

Vibrated for a period of 4 hours in 3 perpendicular directions

each other (for total of 12 hours.)

6.0±1.0mm

Solder

Fig-1

2.5N (10 sec.)

Fig-2

2.5N

90˚

Fig-3

∗•R25 is zero-power resistance of Thermistor in 25°C.

•After each test, NTC Thermistor should be kept for 1 hour at room temperature (normal humidity and normal atmospheric pressure).

Then the resistances (R25 and R50) should be measured and the appearance should be visually examined.

For NTC Thermistors Lead Type Specifications and Test Methods

22

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For NTC Thermistors Lead Type !Caution/Notice

23

3

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ !Caution (Storage and Operating Condition)

This product is designed for application in an

ordinary environment (normal room temperature,

humidity and atmospheric pressure).

Do not use under the following conditions because

all these factors can deteriorate the product

characteristics or cause failures and burn-out.

1. Corrosive gas or deoxidizing gas

(Chlorine gas, Hydrogen sulfide gas, Ammonia gas,

Sulfuric acid gas, Nitric oxide gas, etc.)

2. Volatile or flammable gas

3. Dusty conditions

4. Under vacuum, or under high or low-pressure

5. Wet or humid locations

6. Places with salt water, oils, chemical liquids or

organic solvents

7. Strong vibrations

8. Other places where similar hazardous conditions

exist

■ !Caution (Other)

Be sure to provide an appropriate fail-safe function

on your product to prevent secondary damages that may be

caused by the abnormal function or the failure of our

product.

■ Notice (Storage and Operating Condition)

To keep solderability of product from declining, the

following storage condition is recommended.

1. Storage condition:

Temperature -10 to +40 degrees C

Humidity less than 75%RH (not dewing condition)

2. Storage term:

Use this product within 6 months after delivery by

first-in and first-out stocking system.

3. Handling after unpacking:

After unpacking, reseal product promptly or

store it in a sealed container with a drying agent.

4. Storage place:

Do not store this product in corrosive gas

(Sulfuric acid gas, Chlorine gas, etc.) or in direct

sunlight.

■ Notice (Rating)

Use this product within the specified temperature

range.

Higher temperature may cause deterioration of the

characteristics or the material quality of this

product.

■ Notice (Soldering and Mounting)

1. Be sure that the preheat-up does not melt the

soldering of this product. Excessive heat may

cause failure to open, short or insulation break

down.

2. Do not touch the body with soldering iron.

The soldering point should be min. 5mm away from

the root of lead wire.

■ Notice (Handling)

1. The ceramic element of this product is fragile, and

care must be taken not to load an excessive

press-force or not to give a shock at handling.

Such forces may cause cracking or chipping.

2. Do not apply an excessive force to the lead.

Otherwise, it may cause junction between lead and

element to break or crack. Holding element by side

lead wire is recommended when lead wire is bent or

cut.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

24

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

NTC/PTC Thermistors for Automotive

PTC Thermistor (POSISTORr) for Overheat Sensing Chip Type 0603 (1608) Size

This chip "POSISTOR" is SMD type for overheat sensing

for power transistors, power diodes and power ICs in

hybrid circuits.

■ Features

1. SMD type is helpful for miniaturizing the circuit

because of small size and lightweight.

2. Excellent thermal response because of no coating.

3. Elements of solid-state construction provides

excellent mechanical vibration and impact

resistance.

4. Contactless operation provides prolonged service

life and noiseless operation.

5. Lead is not contained in the terminations.

L

T

Part Number

L W T

Dimensions (mm)

e g

1.6±0.15 0.8±0.15 0.8±0.15 0.1 to 0.6

-

PRF18_RB

W

e eg

Part Number Sensing Temperature

(at 4.7k ohm)

(°C)

Maximum

Voltage

(V)

Resistance

(at 25°C)

(ohm)

Temperature Range

(°C)

PRF18BG471QS2RB 65 ±5°C 32 470 ±50% -40 to 150

PRF18BF471QS2RB 75 ±5°C 32 470 ±50% -40 to 150

PRF18BE471QS2RB 85 ±5°C 32 470 ±50% -40 to 150

PRF18BD471QS2RB 95 ±5°C 32 470 ±50% -40 to 150

PRF18BC471QS2RB 105 ±5°C 32 470 ±50% -40 to 150

PRF18BB471QS2RB 115 ±5°C 32 470 ±50% -40 to 150

PRF18BA471QS2RB 125 ±5°C 32 470 ±50% -40 to 150

PRF18AR471QS2RB 135 ±5°C 32 470 ±50% -40 to 150

PRF18AS471QS2RB 145 ±5°C 32 470 ±50% -40 to 150

Please contact us for UL recognized products.

■ Standard Land Pattern Dimensions

a

c

Solder resist

(in mm)

b

Land

Chip

Part Number Chip (LgW) a

Dimensions (mm)

b c

1.6g0.8

Soldering

Methods

Flow Soldering 0.6-1.0 0.8-0.9 0.6-0.8

Reflow Soldering 0.6-0.8 0.6-0.7 0.6-0.8

PRF18

■ Resistance - Temperature Characteristics (Typical)

–40 –20 0 20 40 60

Temperature (˚C)

80 100 120 140 160

1

0.1

10

100

1000

Resistance Change (R/R25)

BEBDBCBBBA

AR

AS

BF

BG

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

25

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Overheat Protection Circuit

R1

R2

Thermal

+Vcc

RL

RE

Connection

PTH

■ Overheat Sensing Circuit

R1

RL1

RL2

RE1

RE2

Load

+Vcc

PTH

■ Resistance - Temperature Characteristics Range (Ref. Only)

PRF18BG471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18BF471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18BE471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18BD471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

26

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Resistance - Temperature Characteristics Range (Ref. Only)

PRF18BC471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18BB471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18BA471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18AR471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

PRF18AS471QS2RB

Temperature (°C)

Resistance (Ω)

–20–40 0 20 40 60 80 100 120 140 160

100

100000

10000

1000

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

Soldered PTC on Test Board∗1, and apply force on back side of

Test Board shown below:

Bending Speed: 1.0mm/s

Bending Strength: 2.0mm

Hold time: 5±1 seconds

Board Dimension: 100 A40 A1.6t mm

Board Material: Glass Epoxy

JIS C 5102 term 8.4

Solder temp.: 230±5°C

Solder: Sn63%/Pb37% (or 60%/40%)

Soaking time: 3±0.5 seconds

Soaking position: Until a whole electrode is soaked

Solder temp.: 260±5°C

Solder: Sn63%/Pb37% (or 60%/40%)

Flux: Containing less than 0.2wt% of chlorine.

Soaking time: 10±0.5 seconds

Soaking position: Until a whole electrode is soaked.

Preheating: 150±5°C 3 minutes

Soldered PTC to PCB∗1

+150±3°C leave for 1000±12 hours

No. Item Rating Value Method of Examination

There is no detachment sign of electrode.

Normal appearance

Resistance change: not to exceed ±20%∗2

Normal appearance

Resistance change: not to exceed ±20%∗2

Min. 95% electrode is covered with new solder.

Resistance change: not to exceed ±20%∗2

Resistance change: not exceed ±20%∗2

Normal appearance on the section showed

by slanting line parts of the electrodes on the figure.

Normal appearance

Resistance change: not to exceed ±20%∗2

The resistance value should be within the specified tolerance.

Resistance Value

(at 25˚C)

Adhesive Strength

Vibration

Resistance

1

2

3

Resistance to

Bending of

Substance

Solderability

Dry Heat

Resistance

4

5

Soldering Heat

Resistance

6

7

EIAJ ET-7403 term 9

Prepare soldered PTC to PCB ∗1 and add the force of 5.0N in

the direction shown below. (PTC=POSISTORr)

Soldered PTC to PCB∗1

Vibration: 10-2000-10Hz (20 minutes)

Max. Amplitude: 3.0mm

Vibrate for 4 hours in each of 3 mutually perpendicular planes for

a total of 12 hours. This test condition is according to "MIL-STD-

204D"

After applying maximum operating voltage for 3 minutes and

leaving for 2 hours at 25°C, measured by applying voltage of

less than 1.5Vdc (by a direct current of less than 10mA).

Soldered PTC to PCB∗1

-40±3°C leave for 1000±12 hours

Cold Resistance8

Soldered PTC to PCB∗1

+85±3°C 80-85%RH leave for 1000±12 hours

Damp Heat

Resistance

9

Soldered PTC to PCB∗1

Cycles: 1000 cycles

Soldered PTC to PCB∗1

85±3°C, 80-85%RH (in air), load max. operating voltage for

1000±12 hours

Thermal Shock∗3

High Temperature

Humidity Load

10

11

PTC

FF

Glass Epoxy PCB

50

45±2

45±2Bending

20

R230

(in mm)

PTC

Force

Electrode PTC

Continued on the following page.

Step

1

2-55+0, -3

+125+3, -0

Temp. (°C) 30

30

Time (minutes)

27

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Chip Type of POSISTORr for Overheat Protection Specifications and Test Methods

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

∗1 Above mentioned soldering is done under the following conditions at our site.

• Glass-Epoxy PC board

• Standard land dimension

• Standard solder paste

• Standard solder profile

Above conditions are mentioned in Notice.

∗2 Measure resistance after the test by applying voltage of less than 1.5Vdc by a direct current of less than 10mA after product is left at 25±2°C for 2 hours.

∗3 We cannot guarantee the resistance change in Thermal Shock (No.10) in case of defective mounting.

No. Item Rating Value Method of Examination

Normal appearance

Resistance change: not to exceed ±20%∗2

High Temperature

Load

12 Soldered PTC to PCB∗1

+85±3°C (in air), load max. operating voltage for 1000±12

hours.

Continued from the preceding page.

28

4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Chip Type of POSISTORr for Overheat Protection Specifications and Test Methods

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

29

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

NTC/PTC Thermistors for Automotive

PTC Thermistor (POSISTORr) for Overcurrent Protection Chip Type 0805 (2012) Size

Overcurrent Protection device with resettable function

suitable for current limiting resistor.

This product is chip type PTC thermistor for

overcurrent protection which is suitable for the

following

•Countermeasure for short circuit testing

•Current limiting resistor

■ Features

1. Rapid operation to protect the circuit in an

overcurrent condition abnormality such as a

short circuit.

By removing the overcurrent condition, these

products automatically return to the initial

condition and can be used repeatedly.

2. Suitable for countermeasure to short circuit test

in safety standard

3. Stable resistance after operation due to ceramic

PTC

4. Similar size (0603 size) is possible due to the

large capacity for electric power.

5. Possible to use these products as current

limiting resistors with overcurrent protection

functions

6. SMD type is helpful for miniaturizing circuits

because of its small size and lightweight

7. Lead is not contained in the terminations

L

T

Part Number

L W T

Dimensions (mm)

e g

2.0±0.2

1.25±0.2 0.9±0.2

0.2 min.

0.5 min.

2.0±0.2

1.25±0.2 1.25±0.2

0.2 min.

0.5 min.

PRG21_RA

PRG21_RK

W

e eg

Part Number Max.

Voltage

(V)

Non-operating

Current (at +85°C)

(mA)

Non-operating

Current (at +105°C)

(mA)

Trip Current

(at -40°C)

(mA)

Max.

Current

(mA)

Resistance

(at 25°C)

(ohm)

Temperature

Range

(°C)

PRG21AR420MS1RA 20 25 15 130 590 42 ±20% -40 to 105

PRG21AR220MS1RK 16 45 25 250 900 22 ±20% -40 to 105

■ Standard Land Pattern Dimensions

a

c

Solder resist

(in mm)

b

Land

Chip

Part Number Soldering

Methods Chip (LgW) a

Dimensions (mm)

b c

Reflow Soldering 2.0g1.25 1.0-1.2 0.5-0.7 1.0-1.2

PRG21

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

30

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Protective Threshold Current Range

PRG21AR220MS1RK

300

250

200

150

100

50

0

Current (mA)

Ambient Temperature (°C)

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Protective threshold current

Trip current

Non operating current

PRG21AR420MS1RA

160

140

120

100

80

60

40

20

0

Ambient Temperature (°C)

Current (mA)

Protective threshold current

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Trip current

Non operating current

■ Operating Time (Typical Curve)

PRG21AR220MS1RK

Overcurrent (mA)

Operating Time (sec.)

0 100 200 300 400 500 600

10

8

6

4

2

0

Y40°C

W25°CAmbient Temp.

W85°C

W105°C

PRG21AR420MS1RA

Overcurrent (mA)

Operating Time (sec.)

0 100 200 300 400 500

10

8

6

4

2

0

Y40°C

W25°CAmbient Temp.

W85°C

W105°C

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

No. Item Rating Value Method of Examination

Normal appearance

Resistance change: not to exceed ±20%∗2

-40 to +105°C

Operating Temp. 11 The temperature range with maximum voltage applied to the

POSISTORr.

-40 to +125°C

Operating Temp. 22 The temperature range which with zero voltage applied to

POSISTORrafter it was soldered to PCB.

The resistance value shall be within the specified tolerance.

Resistance Value

(at 25˚C)

3After applying maximum operating voltage for 3 minutes and

leaving for 2 hours at 25°C, measured by applying voltage of

less than 1.5Vdc (by a direct current of less than 10mA).

Without damage

Withstanding

Voltage

4

We apply 120% of the maximum voltage to PTC by rising

gradually for 180±5 seconds at 25°C. (A protective resistor is to

be connected in series, and the inrush current through PTC

must be limited below maximum rated value.)

Soldered PTC on Test Board ∗1, and apply force on back side

of Test Board shown below:

Bending Speed: 1.0mm/s

Bending Strength: 2.0mm

Hold Time: 5±1 seconds

Board Dimension: 100A40A1.6t mm

Board Material: Glass Epoxy

JIS C 5102 term 8.4

Solder Temp.: 230±5°C

Solder: Sn63%/Pb37% (or 60%/40%)

Soaking Time: 3±0.5 seconds

Soaking Position: Until a whole electrode is soaked

Solder: Sn 63%/Pb 37% (or 60%/40%) solder paste

Flux: Containing less than 0.2wt% of chlorine.

Preheating: 150±5°C 3 minutes

Peak Temp.: 260±5°C 10±5 seconds (reflow)

PCB: JIS C 6484

Glass Epoxy PCB

Soldered PTC to PCB∗1

+125±3°C leave for 1000±12 hours.

There is no detachment sign of electrode.

Normal appearance

Resistance change: not to exceed ±20%∗2

Normal appearance

Resistance change: not to exceed ±20%∗2

Min. 95% electrode is covered with new solder.

Resistance change: not to exceed ±20%∗2

Normal appearance

Resistance change: not to exceed ±20%∗2

Adhesive Strength

Vibration

Resistance

5

6

Resistance to

Bending of

Substance

Solderability

Dry Heat

Resistance

7

8

Soldering Heat

Resistance

9

10

EIAJ ET-7403 term 9

Prepare soldered PTC to PCB ∗1 and add a force of 5.0N in the

direction shown below. (PTC=POSISTORr)

Soldered PTC to PCB ∗1

Vibration: 10-2000-10Hz (20 min.)

Max. Amplitude: 3.0mm

Vibrate for 4 hours in each of 3 mutually perpendicular planes for

a total of 12 hours. This test condition is according to "MIL-STD-

204D"

Soldered PTC to PCB∗1

-40±3°C leave for 1000±12 hours.

Cold Resistance11

Soldered PTC to PCB∗1

+85±3°C 80-85%RH leave for 1000±12 hours.

Damp Heat

Resistance

12

PTC

FF

Glass Epoxy PCB

50

45±2

45±2Bending

20

R230

(in mm)

PTC

Force

Continued on the following page.

Soldered PTC to PCB∗1

Cycles: 1000 cycles

Thermal Shock∗3

13 Step

1

2-55+0, -3

+125+3, -0

Temp. (°C) 30

30

Time (minutes)

31

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Chip Type of POSISTORr for Overheat Protection Specifications and Test Methods

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

∗1 Above mentioned soldering is done under the following conditions at our site.

• Glass-Epoxy PC board

• Standard land dimension

• Standard solder paste

• Standard solder profile

Above conditions are mentioned in Notice.

∗2 Measure resistance after the test by applying voltage of less than 1.5Vdc by a direct current of less than 10mA after product is left at 25±2°C for 2 hours.

∗3 We cannot guarantee the resistance change in Thermal Shock (No.10) in case of defective mounting.

No. Item Rating Value Method of Examination

Normal appearance

Resistance change: not to exceed ±20%∗2

High Temperature

Load

15

Soldered PTC to PCB∗1

125±3°C (in air), PTC is applied max. operating voltage for

1.5 hours on and 0.5 hours off. This cycle is repeated for 1000±10

hours.

Continued from the preceding page.

Soldered PTC to PCB∗1

85±3°C, 80-85%RH (in air), load max. operating voltage for

1000±12 hours.

High Temperature

Humidity Load

14

32

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Chip Type of POSISTORr for Overheat Protection Specifications and Test Methods

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For POSISTORr Chip Type !Caution/Notice

33

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ !Caution (Storage and Operating Condition)

This product is designed for application in an

ordinary environment (normal room temperature,

humidity and atmospheric pressure). Do not use under

the following conditions because all these factors

can deteriorate the characteristics or cause product

failure and burn-out.

1. Corrosive gas or deoxidizing gas (Chlorine gas,

Hydrogen sulfide gas, Ammonia gas, Sulfuric acid

gas, Nitric oxide gas, etc.)

2. Volatile or flammable gas

3. Dusty conditions

4. Under vacuum, or under high or low-pressure

5. Wet or humid conditions

6. Places with salt water, oils, chemical liquids or

organic solvents

7. Strong vibrations

8. Other places where similar hazardous conditions

exist

■ !Caution (Other)

Be sure to provide an appropriate fail-safe function

on your product to prevent secondary damage that may be

caused by the abnormal function or the failure of our

product.

■ Notice (Storage and Operating Condition)

To keep solderability of product from declining,

following storage condition is recommended.

1. Storage condition:

Temperature -10 to +40 degrees C

Humidity less than 75%RH (not dewing condition)

2. Storage term:

Use this product within 6 months after delivery

by first-in and first-out stocking system.

3. Handling after unpacking:

After unpacking, promptly reseal this product or

store it in a sealed container with a drying agent.

4. Storage place:

Do not store this product in corrosive gas

(Sulfuric acid, Chlorine, etc.) or in direct

sunlight.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

(2) Drying

After cleaning, promptly dry this product.

To remove the flux after soldering, observe the following

points in order to avoid deterioration of the characteristics

or any change to the external electrodes quality.

(1) Cleaning Conditions

2-propanol

Less than 5 minutes

at room temp.

or

Less than 2 minutes

at 40˚C max.

Less than 1 minute

20W/L Frequency

of several 10kHz

to 100kHz.

Solvent Dipping Cleaning Ultrasonic Cleaning

A sufficient cleaning should be applied to remove flux completely.

In your mounting process, observe the following points in

order to avoid deterioration of the characteristics or

destruction of this product. The mounting quality of this

product may also be affected by the mounting conditions,

shown in the points below.

(1) Printing Conditions of Solder Paste

(a) Recommended thickness of solder paste printing

should be from 0.15 to 0.20mm.

(b) After soldering, the solder fillet should be a height

from 0.2 mm to the thickness of this product (see the

figure at right).

(c) Too much solder gives too strong mechanical stress

to this product. Such stress may cause cracking or

other mechanical damage. Also, it can destroy the

electrical performance of this product.

0.2mm V T V E

T

Solder

Electrode

1. Solder and Flux

2. Cleaning Conditions and Drying

3. Soldering Conditions

(1) Solder Paste

(a) Flow Soldering: Use Sn:Pb=60:40wt%,

Sn:Pb=63:37wt%, Sn:Ag:Cu=96.5:3.0:0.5wt% or

equivalent type of solder.

(b) Reflow Soldering: Use Sn:Pb=60:40wt%,

Sn:Pb=63:37wt%, Sn:Ag:Cu=96.5:3.0:0.5wt% or

equivalent type of solder paste.

For your reference, we are using '63Sn/37Pb

RMA9086 90-3-M18', manufactured by Alpha Metals

Japan Ltd., '96.5Sn/3.0Ag/0.5Cu M705-221BM5-42-

11', manufactured by Senju Metal Industry Co., Ltd.

for any Internal tests of this product.

(2) Flux

Use rosin-based flux. Do not use strong acidic flux (with

halide content exceeding 0.2wt%).

E

Continued on the following page.

■ Notice (Soldering and Mounting) 0603 (1608) Size

For POSISTORr Chip Type !Caution/Notice

34

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

Continued from the preceding page.

Time (sec.)

0 10 20 30 40 50 60

260

250

270

240

230

220

210

200

Allowable Reflow Soldering Temp. and Time

Temperature (°C)

(2) Adhesive Application and Curing

(a) If insufficient adhesive is applied, or if the adhesive

is not sufficiently hardened, this product may have a

loose contact with the land, during flow soldering.

(b) Too low viscosity of adhesive causes this product to

slip on board, after mounting.

(3) Allowable Soldering Temperature and Time

(a) Solder within the temperature and time

combinations, indicated by the slanted lines in the

following graphs.

(b) The excessive soldering conditions may cause

dissolution of metallization or deterioration of solder-

wetting on the external electrode.

(c) In the event that soldering is repeated more than

twice, the allowable reflow soldering time should be

the accumulated soldering time.

(4) Recommendable Temperature Profile for Soldering

(a) Insufficient preheating may cause a crack on

ceramic body. Difference between preheating

temperature and maximum temperature in the profile

should be 100°C.

(b) Rapid cooling by dipping in solvent or by other

means is not recommended.

(5) There may be a risk of unexpected failures

(tombstone, insufficient solder-wetting, etc.) in the

mounting process caused by the mounting conditions.

Please make sure that this product is correctly mounted

under specified mounting conditions.

,,

































QQRR

R

SS

S

TUUVVW

X

XX

Y

YYZ

[

\

\\

]

^^

^

_

`

`¢¢££

£

¤¤

¤

¥¦¦§§¨

©

©©

ª

ªª«

¬





®

¯¯

¯

°

±

Soldering Gradual cooling

(in air)

Preheating (in air)

1 to 2 min.

200

100

0

240°C

Flow Soldering Conditions

* In the event that soldering is repeated more than twice the

accumulated soldering time should be in the above allowable

soldering time (3).

*3 sec.max.

Preheating: 150±10°C, 1-2 minutes.

Soldering: 240°C, 3 seconds max.

Temperature (°C)

,



















Q

Q

R

S

T

UU

U

V

WXXYYZ[[\\]

^

_

__``¢

¢

£

¤

¥

¦¦

¦

§

¨©©ªª«¬¬®

¯

°

°°±±

Soldering Gradual cooling

(in air)

Preheating (in air)

1 to 2 min.

200

100

0

240°C

Reflow Soldering Conditions

* In the event that soldering is repeated more than twice the

accumulated soldering time should be in the above allowable

soldering time (3).

*20 sec.max.

Preheating: 150±10°C, 1-2 minutes.

Soldering: 240°C, 20 seconds max.

Temperature (°C)

Time (sec.)

0 10 20 30

260

250

270

240

230

220

210

200

Allowable Flow Soldering Temp. and Time

Temperature (°C)

For POSISTORr Chip Type !Caution/Notice

35

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

(2) Drying

After cleaning, promptly dry this product.

To remove the flux after soldering, observe the following

points in order to avoid deterioration of the characteristics

or any change to the external electrodes quality.

(1) Cleaning Conditions

2-propanol

Less than 5 minutes

at room temp.

or

Less than 2 minutes

at 40˚C max.

Less than 1 minute

20W/L Frequency

of several 10kHz

to 100kHz.

Solvent Dipping Cleaning Ultrasonic Cleaning

A sufficient cleaning should be applied to remove flux completely.

(1) Printing Conditions of Solder Paste

(a) Standard thickness of solder paste printing should

be from 0.15 to 0.20 mm.

(b) After soldering, the solder fillet should be a height

from 0.2 mm to the thickness of this product (see the

figure at right).

(c) Too much solder gives too strong mechanical stress

to this product. Such stress may cause cracking or

other mechanical damage. Also, it can destroy the

electrical performance of this product.

In your mounting process, observe the following points in

order to avoid deterioration of the characteristics or

destruction of this product. The mounting quality of this

product may also be affected by the mounting conditions,

shown in the points below.

This product is for reflow soldering only. Flow soldering

should not be allowed.

0.2mm V T V E

T

Solder

Electrode

1. Solder and Flux

2. Cleaning Conditions and Drying

3. Soldering Conditions

(1) Solder Paste

Use solder paste Sn:Pb=63:37wt%.

For your reference, we are using

63Sn/37Pb RMA9086 90-3-M18,

manufactured by Alpha Metals Japan Ltd.

96.5Sn/3.0Ag/0.5Cu M705-221BM5-42-11,

manufactured by Senju Metal Industry Co., LTD for any

Internal tests of this product.

(2) Flux

Use rosin-based flux. Do not use strong acidic flux

(with halide content exceeding 0.2wt%).

E

Continued on the following page.

■ Notice (Soldering and Mounting) 0805 (2012) Size

For POSISTORr Chip Type !Caution/Notice

36

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

(3) Standard Temperature Profile for Soldering

(a) Insufficient preheating may cause a crack on

ceramic body. Difference between preheating

temperature and maximum temperature in the profile

should be 100D.

(b) Rapid cooling by dipping in solvent or by other

means is not recommended.

,

















Q

Q

R

ST

T

UU

U

VWXXYZ[[\\]

^

_

__`¢

¢

£

¤¥

¥

¦¦

¦

§¨©©ª«¬¬®

¯

°

°°±

Soldering Gradual cooling

(in air)

Preheating (in air)

1 to 2 min.

200

100

0

240°C

Reflow Soldering Conditions

*In the event that soldering is repeated more than twice the

accumulated soldering time should be in the above allowable

soldering time (2).

*20 sec.max.

Preheating: 150T10°C, 1 to 2 minutes

Soldering: 240°C, 20 seconds max.

(4) There may be a risk of unexpected failures

(tombstone, insufficient solder-wetting, etc.) in the

mounting process, caused by the mounting conditions.

Please make sure that this product is correctly

mounted under specified mounting conditions.

(2) Allowable Soldering Temperature and Time

(a) Solder within the temperature and time

combinations, indicated by the slanted lines in the

graphs at right.

(b) The excessive soldering conditions may cause

dissolution of metallization or deterioration of solder-

wetting on the external electrode.

(c) In the event that soldering is repeated more than

twice, the allowable reflow soldering time should be

the accumulated soldering time.

Time (second)

0 10 20 30 40 50 60

260

250

270

240

230

220

210

200

Continued from the preceding page.

Allowable Reflow Soldering Temp. and Time

Temperature (°C)

For POSISTORr Chip Type !Caution/Notice

37

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For POSISTORr Chip Type !Caution/Notice

38

5

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Notice (Handling)

1. Do not give this product a strong press-force nor a

mechanical shock, because such mechanical forces may

cause cracking or chipping of this ceramic product.

Locate chip

horizontal to the

direction in

which stress

acts

Put this product on the

PC Board near the Slit,

not near the

Perforation Holes.

Keep this product on

the PC Board away

from the Separation

Line.

Worst A-C-B-D Better

Component Direction

Chip Mounting Close to Board Separation Point

A

B

D

C

Perforation Holes

Slit

Separation Line

2. Rapid cooling or heating during soldering is not

recommended.

Such treatment may destroy the element.

3. Resin coating

Please select a resin material with minimum hardness.

Shrinkage is much less if selecting a resin material.

4. Location on Printed Circuit Board (PC Board)

Choose a mounting position that minimizes the stress

imposed on the chip during flexing or bending of the

board. (Worse) (Better)

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

39

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

NTC/PTC Thermistors for Automotive

PTC Thermistor (POSISTORr) for Overcurrent Protection Lead Type

16V Series

This low-voltage, low-resistance type "POSISTOR" is

a circuit protector whose resistance value in normal

operation is very low and in abnormal situations like

motor lock or short circuit, will be increased to

restrain over current. This "POSISTOR" is most

suitable for low-voltage circuits and motor protection

for automotive grade applications.

■ Features

1. Best suited to meet the requirements for power

supply and motor protection. Error-free operation

is assured by rush current.

2. Circuit is protected until current is turned off.

3. Restores the original low resistance value

automatically once the overload is removed.

4. Non-contact design leads to long life and no noise.

Durable and strong against mechanical vibration and

shock because it is a solid element.

5. Lead (Pb) is not contained in the terminations.

F±1.5 φd±0.05

D max. T max.

H max.4.0±1.5

(in mm)

Part Number Max.

Voltage

(V)

Non-operating

Current (at +85°C)

(mA)

Trip Current

(at -30°C)

(mA)

Max.

Current

(A)

Resistance

(at 25°C)

(ohm)

Temperature

Range

(°C)

Body

Diameter (D)

(mm)

Thickness

(T)

(mm)

Height

(H)

(mm)

Lead

Space (F)

(mm)

Lead

Diameter

(phi d)(mm)

PTGL5SAR1R0M1B51B0 16 252 1095 2.0 1.0 ±20% -30 to 85 6.0 3.5 9.5 5.0 0.6

PTGL6SAR0R8M1B51B0 16 274 1193 3.0 0.8 ±20% -30 to 85 6.5 3.5 10.0 5.0 0.6

PTGL7SARR47M1B51B0 16 376 1634 5.0 0.47 ±20% -30 to 85 7.5 3.5 12.0 5.0 0.6

PTGL9SARR33M1B51B0 16 466 2026 7.0 0.33 ±20% -30 to 85 9.0 3.5 14.0 5.0 0.6

PTGLASARR27M1B51B0 16 545 2369 8.0 0.27 ±20% -30 to 85 10.1 3.5 15.0 5.0 0.6

PTGLCSAR0R2M1B51B0 16 692 3006 9.0 0.2 ±20% -30 to 85 11.3 3.5 16.0 5.0 0.6

PTGLESARR15M1B51B0 16 820 3561 10 0.15 ±20% -30 to 85 13.5 3.5 18.5 5.0 0.6

Maximum Current shows typical capacities of the transformer which can be used.

Taping type of part numbers with "A0" is available (Except PTGLESARR15M1B51B0).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

40

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

30-140V Series

New leaded type POSISTOR for overcurrent protection

as automotive grade can be used with wide temperature

range. This product is suitable for short-protect and

current limiting resistor on power supply equipment.

■ Features

1. This product has useful Protective threshold

current range with wide temperature range.

2. Small fluctuation in the circuit due to resistance

tolerance +/-10%.

3. Quick operating time due to small size compared

with conventional products.

4. Best suited to meet the requirements for power

supply and motor protector. Error-free operations

are assured by rush current.

5. Circuit is protected until current is turned off.

6. Restores the original low resistance value

automatically once the overload is removed.

7. Non-contact design leads to long life and no noise.

Durable and strong against mechanical vibration and

shock because it is a solid element.

8. Lead (Pb) is not contained in the terminations.

F±1.5 φd±0.05

D max. T max.

H max.4.0±1.5

(in mm)

Part Number Max.

Voltage

(V)

Non-operating

Current (at +85°C)

(mA)

Non-operating

Current (at +105°C)

(mA)

Trip Current

(at -40°C)

(mA)

Max.

Current

(A)

Resistance

(at 25°C)

(ohm)

Temperature

Range

(°C)

Body

Diameter (D)

(mm)

Height

(H)

(mm)

Lead

Space (F)

(mm)

Lead

Diameter

(phi d)(mm)

PTGL4SAS100K2N51B0

30 92 65 261 1.5 10 ±10% -40 to 125 4.5 9.5 5.0 0.5

PTGL4SAS100K2B51B0

30 127 89 359 2.0 10 ±10% -40 to 125 4.5 9.5 5.0 0.6

PTGL5SAS3R9K2B51B0

30 204 143 576 3.5 3.9 ±10% -40 to 125 5.5 10.5 5.0 0.6

PTGL7SAS2R7K2B51B0

30 255 179 720 4.5 2.7 ±10% -40 to 125 7.3 12.3 5.0 0.6

PTGL7SAS1R8K2B51B0

30 319 223 902 5.0 1.8 ±10% -40 to 125 7.3 12.3 5.0 0.6

PTGL9SAS1R2K2B51B0

30 422 296 1193 6.0 1.2 ±10% -40 to 125 9.3 14.3 5.0 0.6

PTGLCSAS0R8K2B51B0

30 520 364 1470 7.0 0.8 ±10% -40 to 125 11.5 16.5 5.0 0.6

PTGL4SAS100K3B51B0

51 128 89 361 1.0 10 ±10% -40 to 125 4.5 9.5 5.0 0.6

PTGL5SAS6R8K3B51B0

51 149 105 422 1.5 6.8 ±10% -40 to 125 5.5 10.5 5.0 0.6

PTGL7SAS3R3K3B51B0

51 233 163 659 3.0 3.3 ±10% -40 to 125 7.3 12.3 5.0 0.6

PTGL9SAS2R2K3B51B0

51 313 219 885 4.0 2.2 ±10% -40 to 125 9.3 14.3 5.0 0.6

PTGLCSAS1R2K3B51B0

51 449 315 1270 5.0 1.2 ±10% -40 to 125 11.5 16.5 5.0 0.6

PTGL4SAS220K4N51B0

60 67 47 190 1.0 22 ±10% -40 to 125 4.5 9.5 5.0 0.5

PTGL4SAS220K4B51B0

60 87 61 246 1.0 22 ±10% -40 to 125 4.5 9.5 5.0 0.6

PTGL5SAS100K4B51B0

60 129 90 364 1.5 10 ±10% -40 to 125 5.5 10.5 5.0 0.6

PTGL7SAS5R6K4N51B0

60 142 99 400 2.2 5.6 ±10% -40 to 125 7.3 12.3 5.0 0.5

PTGL7SAS5R6K4B51B0

60 174 122 492 3.0 5.6 ±10% -40 to 125 7.3 12.3 5.0 0.6

PTGL9SAS3R3K4B51B0

60 253 177 714 4.0 3.3 ±10% -40 to 125 9.3 14.3 5.0 0.6

PTGLCSAS2R2K4B51B0

60 334 234 942 5.0 2.2 ±10% -40 to 125 11.5 16.5 5.0 0.6

PTGL4SAS560K6B51B0

140 56 39 159 0.5 56 ±10% -40 to 125 5.5 10.5 5.0 0.6

PTGL5SAS270K6B51B0

140 80 56 227 1.0 27 ±10% -40 to 125 5.5 10.5 5.0 0.6

PTGL7SAS150K6B51B0

140 112 79 317 1.5 15 ±10% -40 to 125 7.3 12.3 5.0 0.6

PTGL9SAS120K6B51B0

140 146 102 413 2.0 12 ±10% -40 to 125 9.3 14.3 5.0 0.6

PTGL9SAS7R6K6B51B0

140 172 121 486 2.2 7.6 ±10% -40 to 125 9.3 14.3 5.0 0.6

PTGLCSAS4R7K6B51B0

140 236 165 666 3.5 4.7 ±10% -40 to 125 11.5 16.5 5.0 0.6

Maximum Current shows typical capacities of the transformer which can be used.

These series are recognized by UL.

Taping type is also available (PTGL_A0 series).

Thickness

(T)

(mm)

3.5

4.5

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

41

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ Protective Threshold Current Range (16V Series)

PTGL5SAR1R0M1B51B0

1400

1200

1000

800

600

400

200

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Trip current

Non operating current

Protective threshold

current

PTGL6SAR0R8M1B51B0

1400

1200

1000

800

600

400

200

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Trip current

Non operating current

Protective threshold

current

PTGL7SARR47M1B51B0

2000

1800

1600

1400

1200

1000

800

600

400

200

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Protective threshold

current

Trip current

Non operating current

PTGL9SARR33M1B51B0

2600

2400

2200

2000

1800

1600

1400

1200

1000

800

600

400

200

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Trip current

Non operating current

Protective threshold

current

PTGLASARR27M1B51B0

3000

2800

2600

2400

2200

2000

1800

1600

1400

1200

1000

800

600

400

200

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Trip current

Non operating current

Protective threshold

current

PTGLCSAR0R2M1B51B0

4000

3500

3000

2500

2000

1500

1000

500

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Trip current

Non operating current

Protective threshold

current

PTGLESARR15M1B51B0

4000

3500

3000

2500

2000

1500

1000

500

0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Ambient Temperature (°C)

Current (mA)

Trip current

Non operating current

Protective threshold

current

■ Protective Threshold Current Range (30V Series)

PTGL4SAS100K2N51B0

300

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

42

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Protective Threshold Current Range (30V Series)

PTGL4SAS100K2B51B0

400

350

300

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL5SAS3R9K2B51B0

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL7SAS2R7K2B51B0

800

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL7SAS1R8K2B51B0

1000

900

800

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL9SAS1R2K2B51B0

1400

1200

1000

800

600

400

200

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGLCSAS0R8K2B51B0

1600

1400

1200

1000

800

600

400

200

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

■ Protective Threshold Current Range (51V Series)

PTGL4SAS100K3B51B0

400

350

300

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL5SAS6R8K3B51B0

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

43

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Protective Threshold Current Range (51V Series)

PTGL7SAS3R3K3B51B0

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL9SAS2R2K3B51B0

1000

900

800

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGLCSAS1R2K3B51B0

1400

1200

1000

800

600

400

200

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

■ Protective Threshold Current Range (60V Series)

PTGL4SAS220K4N51B0

200

180

160

140

120

100

80

60

40

20

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL4SAS220K4B51B0

300

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL5SAS100K4B51B0

400

350

300

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL7SAS5R6K4N51B0

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL7SAS5R6K4B51B0

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

44

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Protective Threshold Current Range (60V Series)

PTGL9SAS3R3K4B51B0

800

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGLCSAS2R2K4B51B0

1000

800

600

400

200

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

■ Protective Threshold Current Range (140V Series)

PTGL4SAS560K6B51B0

180

160

140

120

100

80

60

40

20

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL5SAS270K6B51B0

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL7SAS150K6B51B0

350

300

250

200

150

100

50

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL9SAS120K6B51B0

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGL9SAS7R6K6B51B0

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

PTGLCSAS4R7K6B51B0

700

600

500

400

300

200

100

0

-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Ambient Temperature (°C)

Current (mA)

Protective

threshold current

Trip current

Non operating current

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

45

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Operating Time (Typical Curve) (16V Series)

PTGL5SAR1R0M1B51B0

100

10

1

0.10.1 1 10

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

PTGL6SAR0R8M1B51B0

100

10

1

0.10.1 1 10

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

PTGL7SARR47M1B51B0

100

10

1

0.10.1 1 10

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

PTGL9SARR33M1B51B0

100

10

1

0.10.1 1 10 100

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

PTGLASARR27M1B51B0

100

10

1

0.10.1 1 10 100

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

PTGLCSAR0R2M1B51B0

100

10

1

0.10.1 1 10 100

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

PTGLESARR15M1B51B0

100

10

1

0.10.1 1 10 100

Overcurrent (A)

Operating Time (sec.)

-30°C

+25°C

+85°CAmbient

Temp.

■ Operating Time (Typical Curve) (30V Series)

PTGL4SAS100K2N51B0

0.01

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

46

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Operating Time (Typical Curve) (30V Series)

PTGL4SAS100K2B51B0

0.01

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL5SAS3R9K2B51B0

0.01

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL7SAS2R7K2B51B0

0.01

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL7SAS1R8K2B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL9SAS1R2K2B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGLCSAS0R8K2B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

Ambient Temp.

- 30°C

- 10°C

25°C

60°C

85°C

■ Operating Time (Typical Curve) (51V Series)

PTGL4SAS100K3B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL5SAS6R8K3B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

47

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Operating Time (Typical Curve) (51V Series)

PTGL7SAS3R3K3B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL9SAS2R2K3B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGLCSAS1R2K3B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

Ambient Temp.

- 30°C

- 10°C

25°C

60°C

85°C

■ Operating Time (Typical Curve) (60V Series)

PTGL4SAS220K4N51B0

0.01

0.1

1

10

100

0.01 0.1 1

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL4SAS220K4B51B0

0.01

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL5SAS100K4B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL7SAS5R6K4N51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL7SAS5R6K4B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

Continued on the following page.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

48

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Continued from the preceding page.

■ Operating Time (Typical Curve) (60V Series)

PTGL9SAS3R3K4B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGLCSAS2R2K4B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

■ Operating Time (Typical Curve) (140V Series)

PTGL4SAS560K6B51B0

0.1

1

10

100

0.01 0.1 1

Overcurrent (A)

Operating Time (sec.)

Ambient Temp.

- 30°C

- 10°C

25°C

60°C

85°C

PTGL5SAS270K6B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGL7SAS150K6B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°CAmbient Temp.

85°C

PTGL9SAS120K6B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

Ambient Temp.

- 30°C

- 10°C

25°C

60°C

85°C

PTGL9SAS7R6K6B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

PTGLCSAS4R7K6B51B0

0.1

1

10

100

0.1 1 10

Overcurrent (A)

Operating Time (sec.)

- 30°C

- 10°C

25°C

60°C

85°CAmbient Temp.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

The load is gradually applied to each terminal of POSISTORr

until the force of 4.9N in the axial direction with fixing

POSISTORr's body itself and this load is being kept for 10

seconds.

POSISTORris held so that it is perpendicular to the lead wire

with 2.45N in the axial direction of the lead wire. The lead wire

is slowly bent toward 90° and returned; then it is slowly bent in

the opposite direction and returned to original state.

The lead wire of POSISTORris soaked in a Isopropyl Alcohol

(JIS K 8839) solution (about 25wt%) of colophony (JIS K 5902)

for 5-10 seconds. And, each lead wire is soaked in molten

solder (JIS Z 3282 H60A) at 235±5°C from the bottom to a

point of 2.0-2.5mm for 2±0.5 seconds.

The lead wire of POSISTORris soaked in molten solder (JIS Z

3282 H60A) at 350±10°C from the bottom to a point of 2.0-

2.5mm for 3.5±0.5 seconds.

After the device is left at room temperature (25°C) for 24±4

hours, the resistance is measured.

No. Item Rating Value Method of Examination

No problem

Satisfies ratings

(Trip Current, Non-operating Current)

No damage

Lead wire does not come off

Solder is applied around the lead wire covering 3/4

or more of the circumference without gap in the axial

direction.

∆R/R25V±15%

-30 to +85°C

Satisfies specification

Operating Temperature

Resistance (R25)

Withstanding Voltage

1

2

3

Protective Threshold Current

Tensile Strength of Lead

Wire Terminal

Solderability

4

5

Bending Strength of Lead

Wire Terminal

6

7

Resistance value is measured by applying voltage under

1.5Vdc (by a direct current of less than 10mA) at 25°C. (But it

must be measured after maximum voltage is applied 180

seconds and then is left for 2 hours at 25°C.)

We apply AC voltage 110% that of the maximum voltage to

POSISTORrby raising voltage gradually for 180±5 seconds at

25°C. (A protective resistor is to be connected in series, and

the inrush current through POSISTORrmust be limited below

maximum rated value.)

Maximum current measured in this examination. Voltage is

applied to POSISTORrin 3 minutes step by step on still air.

Stable current is measured at each step.

The temperature range with maximum voltage applied to the

POSISTORr.

At 85±3°C chamber, POSISTORris applied max. voltage for

1.5 hr on and 0.5 hr off. This cycle is repeated for 500±10

hours, and after the device is left at room temperature (25°C)

for 1 hour, the resistance measurement is performed. (A

protective resistance is to be connected in series and the

inrush current through POSISTORrmust be limited below

max. rated value.)

Terminal Durability of

Soldering

8

∆R/R25V±20%

No damage about marking

POSISTORris set in an environmental chamber at 40±2°C

and 90% to 95% humidity, for 500±4 hours.

And, after the device is left at room temperature (25°C) for

1 hour, the resistance measurement is performed.

Heat Resistant9

∆R/R25V±20%

No damage about marking

Resistance to Damp Heat10

■16V Series

POSISTORr Lead Type for Overheat Protection Specifications and Test Methods

49

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

Maximum current measured in this examination. Voltage is

applied to POSISTORrin 3 minutes step by step on still air

based on “Protective Threshold Current Test Conditions”

shown in next page. Stable current is measured at each step.

The load is gradually applied to each terminal of POSISTORr

until the force of 4.9N in the axial direction with fixing

POSISTORr's body itself and this load is being kept for 10

seconds.

POSISTORris held so that it is perpendicular to the lead wire

with 2.45N in the axial direction of the lead wire. The lead wire

is slowly bent toward 90° and returned; then it is slowly bent in

the opposite direction and returned to original state.

The lead wire of POSISTORris soaked in a Isopropyl Alcohol

(JIS K 8839) solution (about 25wt%) of colophony (JIS K 5902)

for 5-10 sec. And, each lead wire is soaked in molten solder

(JIS Z 3282 H60A) at 235±5°C from the bottom to a point of

2.0-2.5mm for 2±0.5 seconds.

No. Item Rating Value Method of Examination

Satisfies ratings

No problem

Satisfies ratings

(Trip Current, Non-operating Current)

No damage

Lead wire does not come off

Solder is applied around the lead wire covering 3/4

or more of the circumference without gap in the axial

direction.

-30 to +125°C

-40 to +125°C

Operating Temperature 1

Operating Temperature 2

Resistance (R25)

1

2

3

Withstanding Voltage

Protective Threshold Current

Bending Strength of Lead

Wire Terminal

4

5

Tensile Strength of Lead

Wire Terminal

6

7

The temperature range with following voltage applied to the

POSISTORr.

30V and 51V series: max. 16V, 60V series: max. 30V, 140V

series: max. 140V

Resistance value is measured by applying voltage under

1.0Vdc (by a direct current of less than 10mA) at 25°C. (But it

must be measured after it is applied maximum voltage for 180

seconds and then is left for 2 hours at 25°C.)

We apply AC voltage 120% that of the maximum voltage to

POSISTORrby raising voltage gradually for 180±5 seconds at

25°C. (A protective resistor is to be connected in series, and

the inrush current through POSISTORrmust be limited below

max. rated value.)

The temperature range with maximum voltage applied to the

POSISTORr.

The lead wire of POSISTORris soaked in molten solder (JIS Z

3282 H60A) at 350±10°C from the bottom to a point of 2.0-

2.5mm for 3.5±0.5 sec.

After the device is left at room temperature (25°C) for 24±4

hours, the resistance is measured.

Solderability8

∆R/R25V±15%

Acceleration: 98m/s2(10G)

Width: 1.5mm

Vibration: 10-500-10Hz

Vibrate for 11minutes Z24 cycles in each of 3 mutually

perpendicular planes for a total of 13.5 hours.

Terminal Durability of

Soldering

9

∆R/R25V±20%

POSISTORris set in an environmental chamber at 125±3°C

for 1000±12 hours. After the device is left at room temperature

(25°C) for one hour, the resistance measurement is performed.

Vibration Resistant10

POSISTORris set in an environmental chamber at -40±3°C

for 1000±12 hours. After the device is left at room temperature

(25°C) for one hour, the resistance measurement is performed.

Heat Resistant11

POSISTORris set in an environmental chamber at 85±3°C

and 80-85% humidity for 1000±12 hours. After the device is left

at room temperature (25°C) for one hour, the resistance

measurement is performed.

Cold Resistant

Resistance to Damp Heat

12

13

Continued on the following page.

■30-140V Series

POSISTORr Lead Type for Overheat Protection Specifications and Test Methods

50

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

25.0

5.0

2.5

1.0

fai 0.9

25.0

2.5 2.5

3.0

(in : mm)

D.C POWER

SUPPLY D.V +

-

POSISTORr

1Ω

Digital

Voltmeter D.V +

-Digital

Voltmeter

Continued from the preceding page.

Materials: Phenol

Size: 50x50xt1.6mm

Land Pattern: Cu land without through hole

(1) Substrate

(3) Measurement circuit

Solder POSISTORr on the substrate, then put the cover

(150mm cubed) surround POSISTORr to prevent flow of

wind.

(2) Measurement condition

Protective Threshold current test conditions

POSISTORr Lead Type for Overheat Protection Specifications and Test Methods

51

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

POSISTORr Lead Type for Overheat Protection !Caution/Notice

52

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

■ !Caution (Storage and Operating Condition)

This product is designed for application in an

ordinary environment (normal room temperature,

humidity and atmospheric pressure). Do not use under

the following conditions because all these factors

can deteriorate the characteristics or cause product

failure and burn-out.

1. Corrosive gas or deoxidizing gas (Chlorine gas,

Hydrogen sulfide gas, Ammonia gas, Sulfuric acid

gas, Nitric oxide gas, etc.)

2. Volatile or flammable gas

3. Dusty conditions

4. Under vacuum, or under high or low-pressure

5. Wet or humid conditions

6. Places with salt water, oils, chemical liquids or

organic solvents

7. Strong vibrations

8. Other places where similar hazardous conditions

exist

■ !Caution (Other)

Be sure to provide an appropriate fail-safe function

on your product to prevent secondary damage that may be

caused by the abnormal function or the failure of our

product.

■ Notice (Storage and Operating Condition)

To keep solderability of product from declining,

following storage condition is recommended.

1. Storage condition:

Temperature -10 to +40 degrees C

Humidity less than 75%RH (not dewing condition)

2. Storage term:

Use this product within 6 months after delivery

by first-in and first-out stocking system.

3. Handling after unpacking:

After unpacking, promptly reseal this product or

store it in a sealed container with a drying agent.

4. Storage place:

Do not store this product in corrosive gas

(Sulfuric acid, Chlorine, etc.) or in direct

sunlight.

■ Notice (Soldering and Mounting)

When the lead of this product is soldered, pay

attention as follows to avoid the decline of element

characteristics or break-down of the element.

1. Use Rosin type flux or non-activated flux

2. Do not dip the body into flux (flux should be coated

to lead wire only for soldering).

3. Be sure that preheating does not melt the

soldering of this product.

■ Notice (Handling)

1. Do not apply an excessive force to the lead.

Otherwise, it may cause the junction between lead

and element to break, or may crack the element.

Therefore, holding the element side lead wire is

recommended when lead wire is bent or cut.

2. This product does not have waterproof

construction. Splashed water may cause failure

mode such as decline of characteristics or current

leak.

3. When this product is operated, temperature of some

areas may be over 100 to 160 degrees C. Be sure that

surrounding parts and inserting material can

withstand the temperature. If the surrounding part

and material are kept under such conditions, they

may deteriorate or produce harmful gas

(Chlorine gas, Hydrogen sulfide gas, Ammonia gas,

Sulfuric acid gas, Nitric oxide gas, etc.). And

such harmful gas may deteriorate the element.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

NCP15

NCP18

10000

4000

Part Number Paper Tape

-

Embossed Tape

Quantity (pcs.)

(in mm)

40 min. 190-250

Vacant Section

210-250

Top Tape alone

Cover Tape alone

Leader Unit

Trailer Unit

Chip-mounting Unit

Direction of Feed

ø178±2.0

ø21.0±0.8

ø13.0±0.5

ø50 min.

2.0±0.5

10.0±1.5 2.0±0.5

(1) A tape in a reel contains Leader unit and Trailer unit where

products are not packed. (Please refer to the figure at right.)

(2) The top and base tapes or plastic and cover tape are not

stuck at the first five pitches minimum.

(3) A label should be attached on the reel. (MURATA's part

number, inspection number and quantity should be marked

on the label.)

(4) Taping reels are packed in a package.

1. Dimensions of Reel

2. Taping Method

Tape Carrier Packaging

Minimum Quantity Guide

Continued on the following page.

1

For NTC Thermistors Chip Type Package

53

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

(1) Other Conditions

q Packaging

Products are packaged in the cavity of the base tape and

sealed by top tape and bottom tape.

w Tape

Top tape and bottom tape have no joints and products

are packaged and sealed in the cavity of the base tape,

continuously.

(2) Peeling Force of Top Tape

(3) Pull Strength

Pull strength of top tape is specified at 10N minimum.

Pull strength of bottom tape shall be specified 5N minimum.

3. Paper Tape (NCP15/18 Series)

NCP15 Series

8mm Width 2mm Pitch Tape NCP18 Series

8mm Width 4mm Pitch Tape

1.1 max.

4.0±0.1 4.0±0.1

2.0±0.05 ø1.5

1.75±0.1

3.5±0.05

8.0±0.3

Direction of Feed

1.05∗

0.8 max.

4.0±0.1

2.0±0.05 ø1.5

1.75±0.1

3.5±0.05

1.15∗

8.0±0.3

Direction of Feed

0.65∗

(in mm)

∗ Reference Value∗ Reference Value

165-180°F

Peeling Angle: 165 to 180 degree against the fixed surface of tape.

Peeling Speed: 300mm/min.

Peeling Force: 0.1 - 0.6N

Continued from the preceding page.

1.85∗

+0.1

–0 +0.1

–0

2

For NTC Thermistors Chip Type Package

54

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For NTC Thermistors Lead Type Package

55

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Item Code Dimension (mm)

Pitch of Component

Pitch of Sprocket Hole

Lead Spacing

Length from Hole Center to Component Center

Length from Hole Center to Lead

Body Diameter

Deviation along Tape, Left or Right Defect

Carrier Tape Width

Position of Sprocket Hole

Lead Distance between Reference and Bottom Planes

Height of Component

Protrusion Length

Diameter of Sprocket Hole

Lead Diameter

Total Tape Thickness

Total Thickness, Tape and Lead Wire

Deviation across Tape

Portion to Cut in Case of Defect

Hole Down Tape Width

Hole Down Tape Position

Coating Extension on Lead

Body Thickness

P

P0

F

P2

P1

D

∆S

W

W1

H0

H2

I

D0

d

t1

t2

∆h1, ∆h2

L

W0

W2

e

T

12.7

12.7±0.3

5.0+0.8/–0.2

6.35±1.3

3.85±0.8

3.5 max.

0±2.0

18.0±0.5

9.0±0.5

16.0±1.0

4.0 max.

+0.5 to –1.0

4.0±0.1

0.50±0.03

0.6±0.3

1.6 max.

1.0 max.

11.0+0/–2.0

11.0 min.

1.5±1.5

Up to the crimp point

2.6 max.

(in mm)

■ Minimum Quantity Guide

■ Taping Dimension (NTSS_N6A0 Series)

P2

P0I

L

P∆S

H2

W2

W0H0W1

W

t2t1

∆h2∆h1

T

øD0

D

P1ød

F

e

Part Number Taping (Ammo Pack)

Minimum Quantity (pcs.)

Bulk*

NTSS 3000 100

* This quantity differs from actual delivery quantity in a package.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

*1.05 *Reference Value

1.1 max.

1.75±0.1

4.0±0.1

2.0±0.1

4.0±0.1

3.5±0.05

8.0±0.3

Direction feed

(1.85)

(in mm)

ø13.0±0.2

ø21.0±0.8

9.0

ø60

ø180W0

Y1.5

W1.0

Y0

W1.0

Y0

2.0±0.5

13.0±1.0

Reel Dimensions

Part Number Quantity (pcs.)

Paper Tape Embossed Tape

PR*18_RB

PR*21_RA

PR*21_RK

4000

-

4000

3000

1.45±0.1 Direction feed

1.75±0.1

4.0±0.1 4.0±0.1

2.0±0.1

3.5±0.05

8.0±0.3

ø1.5W0.1

Y0

2.25±0.1

ø1.0±0.1

1.30±0.05

0.25±0.05

1.45 Direction feed

1.75±0.1

4.0±0.1 4.0±0.1

2.0±0.1

3.5±0.05

8.0±0.3

ø1.0W0.3

Y0

ø1.5W0.1

Y0

2.25

1.1

0.2

PR*18_RB Series: Paper Tape

PR*21_RA Series: Embossed Tape PR*21_RK Series: Embossed Tape

! Minimum Quantity Guide

! Tape Dimensions

! Reel Dimensions

ø1.5W0.1

Y0

For POSISTORr Chip Type Package

56

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

For POSISTORr Lead Type Package

57

6

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

Pitch of Component

Pitch of Sprocket Hole

Lead Spacing

Length from Hole Center to Lead

Length from Hole Center to Component Center

Body Diameter

Body Thickness

Deviation along Tape, Left or Right Defect

Carrier Tape Width

Position of Sprocket Hole

Lead Distance between Reference and

Bottom Planes

Protrusion Length

Diameter of Sprocket Hole

Lead Diameter

Total Tape Thickness

Total Thickness of Tape and Lead Wire

Deviation across Tape

Portion to cut in Case of Defect

Hold Down Tape Width

Hold Down Tape Position

Coating Extension on Lead

P

P0

F

P1

P2

D

T

∆S

W

W1

H0

H2

I

D0

d

t1

t2

∆h1, ∆h2

L

W0

W2

e

12.7

12.7±0.3

5.0

3.85±0.8

6.35±1.3

Please see in Ratings

±1.5

18.0±0.5

16.0±1.0

6.0 max.

W0.5 — Y1.0

4.0±0.2

Please see in Ratings

0.6±0.3

2.0 max.

1.5 max.

11.0 min.

4.0 max.

Up to the center of crimp

Tolerance is determined by ∆S.

Deviation in the feeding direction

Including the inclination caused by lead bending

Deviation of tape width

CodeItem Dimensions (mm) Note

+0.8

–0.3

9.0+0.5

–0.75

11.0+0

–2.0

W0W2

W

W1

H0H2

∆h2∆h1

e

∆S

P2P

D

P1

P0

Fd

l

ø

D

0

L

t2

t1

T

■ Minimum Quantity Guide

c Taping Dimension (PTGL_A0 Series)

Part Number Taping (Ammo Pack)

Minimum Quantity (pcs.)

Bulk*

PTGL (16V Series)

PTGL (30 to 140V Series)

2000 100

1500 100

* This quantity differs from actual delivery quantity in a package.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21

Note:

1. Export Control

<

For customers outside Japan

>

No muRata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or

otherwise contribution to (1) any weapons (Weapons of Mass Destruction (nuclear, chemical or biological weapons or missiles) or conventional weapons) or (2)

goods or systems specially designed or intended for military end-use or utilization by military end-users.

<

For customers in Japan

>

For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is required

for export.

2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially

high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in

applications other than those specified in this catalog.

qAircraft equipment wAerospace equipment

eUndersea equipment rPower plant equipment

tMedical equipment yTransportation equipment (vehicles, trains, ships, etc.)

uTraffic signal equipment iDisaster prevention / crime prevention equipment

oData-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed above

3. Product specifications in this catalog are as of January 2007. They are subject to change or our products in it may be discontinued without advance notice.

Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or

product engineers.

4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or

transact the approval sheet for product specifications before ordering.

6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect

of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or

contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned

above under licenses without our consent.

7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process.

International Division

3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan

Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: intl@murata.co.jp

Head Office

1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan

Phone: 81-75-951-9111

http://www.murata.com/

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note R03E.pdf

07.3.21