Dimensions in Inches (mm) www.hubbell-wiring.com
Dimensions in Inches (mm) www.hubbell-wiring.com
Section T
Wire Management Products
Index
Product Page Number
Kellems Wire Mesh Grips T-2–3
Pulling Grips T-4–16
DUA-PULL®Grips T-6
DUA-PULL®Feed Tube T-6
Overhead Multiple Strength T-7
Underground Pulling T-8–9
K-Type T-8
T-Type T-9
Special Purpose T-10–11
Non-Conductive T-10
Slack Grip Closed Mesh, Split Mesh T-10–11
Low Tension Light Duty Junior T-12
Wire Rope Splicing T-13
Cable Splicing T-14
Tools and Bands T-15
Swivels and Links T-16
Pulling Grip Technical Information T-17–27
Support Grips T-28–38
Standard Support T-30–33
Heavy Support T-34–35
Service Drop T-36–37
Bus Drop T-38
Conduit Riser T-39–42
Support Grip Technical Information T-43–48
Fiber Optic Cable Grips T-49–57
Pulling T-50–52
Support T-53
Fiber Optic Cable Grips Technical Information T-54–57
Strain Relief for Flexible Cord T-59–74
Deluxe Cord Grips T-60–64
Adaptors for Multi Pin Circular Connectors T-65
I-Grips T-66
Dust Tight Strain Relief Grips T-67
Strain Relief for Flexible Cord Technical Information T-68–74
Cord Connectors for Flexible Cord T-75–96
Straight Male Cord Connectors T-76–78
45° Male Cord Connectors T-79
90° Male Cord Connectors T-80
Straight Female & Underground Feeder T-81
Low Profile Straight Male NPT & PG Thread T-82
Accessories T-83
Hubbell Juniors Miniature Cord Connectors T-84–86
Cord Connectors and Hubbell Juniors Technical Information T-87–98
Strain Relief for Conduit Grips T-99–101
Hose Containment Grips T-102
Strain Relief for Conduit Grips Technical Information T-103–107
Non-Metallic Liquid Tight Conduit & Tubing T-108–109
Non-Metallic Liquid Tight Fittings T-110–111
Metallic Liquid Tight Fittings T-112–113
Non-Metallic Liquid Tight Conduit, Tubing & Fittings T-114–117
Metallic Liquid Tight Fittings T-118
Wire Management Products Index
Kellems®Grips Wire Management Products
T-2 Dimensions in Inches (mm)
www.hubbell-wiring.com
Support
Grip
Pulling
Grip
Seal-Tite®
Conduit
Grip
Strain
Relief
Grip
Deluxe
Cord Grip
Support
Grip
Support
Grip
Seal-Tite®
Conduit
Grip
Wire Management Products Kellems®Grips
T-3
Dimensions in Inches (mm) www.hubbell-wiring.com
Underground
Pulling Grip
Conduit
Riser
Grip
Deluxe
Cord
Grip
Hose
Containment
Grip
Cord
Connector
Strain
Relief
Grip
Bus
Drop
Grip
Deluxe
Cord
Grip
Support
Grip
Overhead
Pulling
Grip
Pulling Grips Wire Management Products
Kellems®Pulling Grips
Overhead, Underground, Commercial Construction, Specialty
Wire Management Products Pulling Grips
Kellems®Pulling Grips
Overhead, Underground, Commercial Construction, Special
2
Dimensions in Inches (mm) www.hubbell-wiring.com
Endless weave allows easy installation onto cable. It has a snag-free
low profile. Reusable tool.
Flexible or rotating eyes will mate easily with line stringing swivels
and links for attachment to pulling lines. They have great strength
for trouble free pulling jobs.
Shoulder protectors contain the cable inside the grip and smooth
the passage of the grip over line stringing blocks or conduit bends.
They protect the leading edge of the grip from abrasion.
The galvanized steel mesh grip provides strength for secure pulling
jobs and a slim profile with little build-up. It has flexibility to follow
cable path.
The multiweave styles available add strength for big pulling jobs
and provide positive gripping power.
Pulling Grips Wire Management Products
Pulling Grips
Overhead Pulling
Flexible Eye, Double Weave Mesh, Galvanized Steel
DUA-PULL®Grips
Read This Data
It is important that you read all breaking
strength, safety and technical data
relating to this product on pages
T-17 through T-27
.
DUA-PULL Grips
Diameter Range Ap
prox. Diameter
Conductor Rope* Breaking Eye B Over Cable
Diameter Diameter Strength E M Diameter & Grip** Color Catalog
Inches (cm) Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Inches (cm) Inches (cm) Code Numbers
.19”-.37” (.48-.94) .25”-.65” (.63-1.65) 6,500 (28,912) 10” (25.40) 24” (60.96) .22” (.55) .20” (.51) Black 033271037
.38”-.62” (.97-1.57) .50”-.90” (1.27-2.29) 14,000 (62,227) 12” (30.48) 36” (91.44) .375” (.95) .280” (.71) Dark Green 033271038
.63”-.87” (1.60-2.21) .75”-1.10” (1.90-2.79) 20,000 (88,960) 13” (33.02) 48” (121.92) .437” (1.11) .360” (.91) Red 033271039
.88”-1.12” (2.24-2.84) 1.00”-1.50” (2.54-3.81) 30,600 (136,109) 15” (38.10) 60” (152.40) .500” (1.27) .500” (1.27) Dark Blue 033271040
1.13”-1.37” (2.87-3.48) 1.25”-1.70” (3.17-4.32) 46,800 (208,166) 18” (45.72) 76” (193.04) .625” (1.59) .625” (1.59) Yellow 033271041
1.38”-1.90” (3.51-4.38) 1.50”-2.10” (3.81-5.33) 66,500 (245,792) 24” (60.96) 89” (226.06) .750” (1.90) .750” (1.90) Aluminum 033271042
E- Eye length M-Mesh length at nominal diameter
*For rope, select smallest size grip which meets required work load.
**Add to cable or rope diameter.
DUA-PULL Feed Tube
For Use Rope Feed Tube
With DUA- Diameter Length Catalog
PULL Grip Inches (cm) Inches (cm) Numbers
033271037 .25”-.65” (.63-1.65) 28” (71.12) 091061043
033271038 .50”-.90” (1.27-2.29) 40” (101.60) 091061044
033271039 .75”-1.10” (1.90-2.79) 52” (132.08) 091061045
033271040 1.00”-1.50” (2.54-3.81) 67” (170.18) 091061046
033271041 1.25”-1.70” (3.17-4.32) 83” (210.82) 091061047
033271042 1.50”-2.10” (3.81-5.33) 96” (243.84) 091061048
EM
B
T-6 Dimensions in Inches (mm)
www.hubbell-wiring.com
DUA-PULL Grips
DUA-PULL Pulling Grips are the highest strength pulling grips manufactured
for overhead transmission line stringing applications. They have a dual
function, not provided by any other grip, of working with both bare and
insulated conductors and synthetic rope.
Wire Management Products Pulling Grips
Pulling Grips
Overhead Pulling
Flexible or Rotating Eye, Triple, Double, Single Weave, Galvanized Steel
Multiple Strength Grips
Multiple Strength Style Grips
Multiple Strength Pulling Grips are designed for pulling ACSR, aluminum or
copper bare conductor, ground wires, messenger strands, wire rope and
insulated cables.
Multiple Strength Grip-Rotating Eye
Cable Diameter Approx. Breaking E M Rotating Eye Color Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Diameter Inches (cm) Code Numbers
.25”-.49” (.63-1.24) 6,800 (20,567) 5” (12.70) 26” (66.04) 7/8” (2.22) Dark Green 03302016
.50”-.74” (1.27-1.88) 10,000 (44,480) 6” (15.24) 32” (81.28) 1” (2.54) Brown 03302018
.75”-.99” (1.90-2.51) 14,400 (64,051) 6” (15.24) 41” (104.14) 1” (2.54) Light Blue 03302020
1.00”-1.24” (2.54-3.15) 24,600 (109,420) 8” (20.32) 52” (132.08) 13/8” (3.49) Gold 03302022
1.25”-1.49” (3.17-3.78) 30,600 (136,109) 8” (20.32) 56” (142.24) 15/8” (4.13) Black 03302024
1.50”-1.74” (3.81-4.42) 30,600 (136,109) 9” (22.86) 60” (152.40) 17/8” (4.76) Red 03302026
1.75”-2.24” (4.44-5.69) 48,000 (213,504) 10” (25.40) 70” (177.80) 17/8” (4.76) Dark Blue 03302028
2.00”-2.49” (5.08-6.32) 48,000 (213,504) 10” (25.40) 50” (127.00) 17/8” (4.76) Yellow 03302066
2.50”-2.99” (6.35-7.59) 48,000 (213,504) 10” (25.40) 52” (132.08) 17/8” (4.76) Orange 03302097
3.00”-3.49” (7.62-8.86) 48,000 (213,504) 10” (25.40) 54” (137.16) 17/8” (4.76) Aluminum 033021030
3.50”-3.99” (8.89-10.13) 48,000 (213,504) 10” (25.40) 58” (142.24) 17/8” (4.76) Light Green 033021031
E-Eye length M-Mesh length at nominal diameter
Multiple Strength Grip-Flexible Eye
Cable Diameter Approx. Breaking E M A-Eye Color Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Diameter Inches (cm) Code Numbers
.25”-.49” (.63-1.24) 6,800 (20,567) 9” (22.86) 26” (66.04) 1/4” (.63) Dark Green 03302044
.50”-.74” (1.27-1.88) 10,000 (44,480) 9” (22.86) 32” (81.28) 5/16” (.79) Brown 03302046
.75”-.99” (1.90-2.51) 14,400 (64,051) 11” (27.94) 41” (104.14) 3/8” (.95) Light Blue 03302048
1.00”-1.24” (2.54-3.15) 24,600 (109,420) 12” (30.48) 52” (132.08) 1/2” (1.27) Gold 03302050
1.25”-1.49” (3.17-3.78) 30,600 (136,109) 12” (30.48) 56” (142.24) 1/2” (1.27) Black 03302052
1.50”-1.74” (3.81-4.42) 30,600 (136,109) 12” (30.48) 60” (152.40) 1/2” (1.27) Red 03302054
1.75”-2.24” (4.44-5.69) 48,000 (215,504) 18” (45.72) 70” (177.80) 5/8” (1.59) Dark Blue 03302056
2.00”-2.49” (5.08-6.32) 48,000 (215,504) 18” (45.72) 50” (127.00) 5/8” (1.59) Yellow 033021078
2.50”-2.99” (6.35-7.59) 48,000 (215,504) 18” (45.72) 52” (132.08) 5/8” (1.59) Orange 033021079
3.00”-3.49” (7.62-8.86) 48,000 (215,504) 18” (45.72) 54” (137.16) 5/8” (1.59) Aluminum 033021080
3.50”-3.99” (8.89-10.13) 48,000 (215,504) 18” (45.72) 58” (142.24) 5/8” (1.59) Light Green 033021081
E-Eye length M-Mesh length at nominal diameter
ME
A
ME
T-7
Dimensions in Inches (mm) www.hubbell-wiring.com
Wire Management Products
Read This Data
It is important that you read all breaking
strength, safety and technical data
relating to this product on pages
T-17 through T-27.
Pulling Grips Wire Management Products
Pulling Grips
Underground Pulling
Rotating Eye, Double Weave, Galvanized Steel
K-Type Grips
Read This Data
It is important that you read all breaking
strength, safety and technical data
relating to this product on pages
T-17 through T-27.
K-Type Grips
Cable Diameter Approx. Breaking E M Rotating Eye Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Diameter Inches (cm) Numbers
Short
.50
”
-.61
”
(.27-1.55) 5,600 (24,909) 5
”
(12.70) 11
”
(27.94) 7/8
”
(2.22) 03301001
.62”-.74” (1.57-1.88) 6,800 (30,246) 5” (12.70) 11” (27.94) 7/8” (2.22) 03301002
.75”-.99” (1.90-2.51) 6,800 (30,246) 6” (15.24) 20” (50.80) 1” (2.54) 03301013
1.00”-1.24” (2.54-3.15) 12,800 (56,934) 7” (17.78) 20” (50.80) 13/8” (3.94) 03301014
1.25”-1.49” (3.17-3.78) 12,800 (56,934) 7” (17.78) 21” (53.34) 13/8” (3.94) 03301016
1.50”-1.99” (3.81-5.05) 16,400 (72,941) 7” (17.78) 25” (63.50) 13/8” (3.94) 03301017
2.00”-2.49” (5.08-6.32) 27,200 (120,986) 8” (20.32) 26” (66.04) 15/8” (4.13) 03301018
2.50”-2.99” (6.35-7.59) 33,000 (146,784) 10” (25.40) 28” (71.12) 17/8” (4.76) 03301019
3.00”-3.49” (7.62-8.86) 41,000 (182,368) 10” (25.40) 30” (76.20) 17/8” (4.76) 03301020
3.50”-3.99” (8.89-10.13) 48,000 (213,504) 10” (25.40) 32” (81.28) 17/8” (4.76) 03301021
4.00”-4.49” (10.16-11.40) 48,000 (213,504) 10” (25.40) 33” (83.82) 17/8” (4.76) 033011017
Standard
.50
”
-.61
”
(.27-1.55) 5,600 (24,909) 5
”
(12.70) 16
”
(40.64) 7/8
”
(2.22) 03301011
.62”-.74” (1.57-1.88) 6,800 (30,246) 5” (12.70) 16” (40.64) 7/8” (2.22) 03301012
.75”-.99” (1.90-2.51) 9,600 (42,700) 6” (15.24) 32” (81.28) 1” (2.54) 03301024
1.00”-1.49” (2.54-3.78) 16,400 (72,947) 7” (17.78) 33” (83.82) 13/8” (3.49) 03301025
1.50”-1.99” (3.81-5.05) 16,400 (72,947) 7” (17.78) 34” (86.36) 13/8” (3.49) 03301026
2.00”-2.49” (5.08-6.32) 27,200 (120,986) 9” (22.86) 36” (91.44) 15/8” (4.13) 03301027
2.50”-2.99” (6.35-7.59) 33,000 (146,784) 10” (25.40) 38” (96.52) 17/8” (4.76) 03301028
3.00”-3.49” (7.62-8.86) 41,000 (182,368) 10” (25.40) 39” (99.06) 17/8” (4.76) 03301029
3.50”-3.99” (8.89-10.13) 48,000 (213,504) 10” (25.40) 41” (104.14) 17/8” (4.76) 03301030
4.00”-4.49” (10.16-11.40) 48,000 (213,504) 10” (25.40) 42” (106.68) 17/8” (4.76) 03301031
4.50”-4.99” (11.43-12.67) 48,000 (213,504) 10” (25.40) 58” (147.32) 17/8” (4.76) 03301039
5.00”-5.99” (12.70-15.21) 48,000 (213,504) 10” (25.40) 60” (152.40) 17/8” (4.76) 03301047
6.00”-6.99” (15.24-17.75) 48,000 (213,504) 10” (25.40) 66” (167.64) 17/8” (4.76) 03301045
E-Eye length M-Mesh length at nominal diameter
Note: Refer to page T-26 for multiple cables in a single pulling grip.
T-8 Dimensions in Inches (mm)
www.hubbell-wiring.com
K-Type Grips
Kellems®Rotating Eye, K-Type Pulling Grips are made of high strength
galvanized steel strand. All Grips feature double weave mesh for greater
strength and added mesh contact on the cable, to handle longer or heavier
pulling jobs. The forged eye mates easily with a swivel or shackle.
ME
Wire Management Products Pulling Grips
Pulling Grips
Underground Pulling
Flexible Eye, Double Weave, Galvanized Steel
T-Type Grips
T-Type Grips
Kellems®Flexible T-Type Pulling Grips are made of high strength galvanized
steel strand. They feature double weave mesh for positive holding power in
medium to heavy pulling jobs. The grip eye will easily attach to a swivel.
T-Type Grips
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
Short
.50”-.61” (1.27-1.55) 4,500 (20,016) 8” (20.32) 21” (53.34) 033041082
.62
”
-.74
”
(1.57-1.88) 5,600 (24,909) 8
”
(20.32) 24
”
(60.96) 033041083
.75
”
-.99
”
(1.90-2.51) 6,800 (30,246) 9
”
(22.86) 24
”
(60.96) 033041084
1.00
”
-1.49
”
(2.54-3.78) 9,600 (42,701) 9
”
(22.86) 24
”
(60.96) 033041085
1.50
”
-1.99
”
(3.81-5.05) 16,400 (72,947) 11
”
(27.94) 24
”
(60.96) 033041086
2.00
”
-2.49
”
(5.08-6.32) 18,500 (82,288) 12
”
(30.48) 24
”
(60.96) 033041087
2.50
”
-2.99
”
(6.35-7.59) 24,500 (108,976) 12
”
(30.48) 24
”
(60.96) 033041088
3.00
”
-3.49
”
(7.62-8.86) 24,500 (108,976) 14
”
(35.56) 24
”
(60.96) 033041089
3.50
”
-3.99
”
(8.89-10.13) 31,000 (137,888) 14
”
(35.56) 26
”
(66.04) 033041090
Standard
.75”-.99” (1.90-2.51) 6,800 (30,246) 9” (22.86) 36” (91.44) 033041091
1.00
”
-1.49
”
(2.54-3.78) 9,600 (42,701) 9
”
(22.86) 36
”
(91.44) 033041092
1.50
”
-1.99
”
(3.81-5.05) 16,400 (72,947) 11
”
(27.94) 36
”
(91.44) 033041093
2.00
”
-2.49
”
(5.08-6.32) 18,500 (82,788) 12
”
(30.48) 36
”
(91.44) 033041094
2.50
”
-2.99
”
(6.35-7.59) 24,500 (108,976) 12
”
(30.48) 36
”
(91.44) 033041095
3.00
”
-3.49
”
(7.62-8.86) 24,500 (108,976) 14
”
(35.56) 36
”
(91.44) 033041096
3.50
”
-3.99
”
(8.89-10.13) 31,000 (137,888) 14
”
(35.56) 40
”
(101.60) 033041097
E-Eye length M-Mesh length at nominal diameter
Note: Refer to page T-26 for multiple cables in a single pulling grip.
T-9
Dimensions in Inches (mm) www.hubbell-wiring.com
Read This Data
It is important that you read all breaking
strength, safety and technical data
relating to this product on pages T-17
through T-27.
ME
Pulling Grips Wire Management Products
Pulling Grips
Special Purpose
T-10 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-17 through T-
27.
Kellems®Non-Conductive Pulling
Grips, made of a high strength,
non-conductive aramid fiber, are
available for pulling single cable or
cable bundles. Their braided double
weave design adds strength and
positive holding power.
Slack Pulling Grips are offered in
three styles made of galavanized
steel. The closed type is used when
the cable end is accessible. When
not, there are split lace and split rod
closing styles. All grips feature a
single offset eye for easy
attachment to a pulling line.
Non-Conductive Grips, Single Eye, Double Weave, Non-Metallic
Approx.
Breaking
Cable Diameter
Strength
E M A Color Catalog
Range Inches (cm)
Lbs. (N)
Inches (cm) Inches (cm) Inches (cm) Code Numbers
.50”-.62” (1.27-1.57) 4,000 (17,782) 5.5” (13.97) 24” (60.96) .44” (1.12) Green 03628001
.63”-.74” (1.60-1.88) 5,000 (22,240) 5.5” (13.97) 26” (66.04) .44” (1.12) Yellow 03628002
.75”-.99” (1.90-2.51) 6,000 (26,688) 6.0” (15.24) 31” (78.74) .63” (1.60) Red 03628003
1.00”-1.24” (2.54-3.15) 6,000 (26,688) 6.5” (16.51) 36” (91.44) .63” (1.60) Blue 03628004
1.25”-1.49” (3.17-3.78) 6,000 (26,688) 6.7” (17.02)
41.5” (105.41)
.63” (1.60) White 03628005
E-Eye length M-Mesh length at nominal diameter
Slack Grip-Closed Mesh,
Single Eye, Double Weave, Galvanized Steel
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
Standard
.75”-.99” (1.90-2.51) 2,600 (11,565) 7” (17.78) 12” (30.48) 03308003
1.00”-1.24” (2.54-3.15) 4,000 (17,792) 8” (20.32) 15” (38.10) 03308004
1.25”-1.49” (3.17-3.78) 5,400 (24,109) 8” (20.32) 16” (40.46) 03308005
1.50”-1.74” (3.81-4.42) 6,600 (29,357) 8” (20.32) 20” (43.18) 03308006
1.75”-1.99” (4.44-5.05) 10,000 (44,480) 10” (25.40) 18” (45.72) 03308007
2.00”-2.49” (5.08-6.32) 11,000 (48,928) 10” (25.40) 19” (48.26) 03308008
2.50”-2.99” (6.35-7.59) 11,000 (48,928) 10” (25.40) 20” (50.80) 03308009
3.00”-3.49” (7.62-8.86) 14,500 (64,496) 12” (30.48) 21” (53.34) 03308010
3.50”-3.99” (8.89-10.13) 14,500 (64,496) 12” (30.48) 22” (55.88) 03308011
E-Eye length M-Mesh length at nominal diameter
Note: Refer to page T-26 for multiple cables in a single pulling grip.
EM
A
ME
Wire Management Products Pulling Grips
Pulling Grips
Special Purpose
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-17 through T-
27.
Slack Pulling Grips are offered in
three styles made of galvanized
steel. The closed type is used when
the cable end is accessible. When
not accessible, there are split lace
and split rod closing styles. All grips
feature single offset eye for easy
attachment to a pulling line.
Slack Grip-Split Mesh, Rawhide Lace Closing,
Single Eye, Double Weave, Galvanized Steel
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
Standard
.75”-.99” (1.90-2.51) 2,500 (11,120) 7” (17.78) 12” (30.48) 03309003
1.00”-1.24” (2.54-3.15) 3,500 (15,568) 8” (20.32) 15” (38.10) 03309004
1.25”-1.49” (3.17-3.78) 4,000 (17,792) 8” (20.32) 16” (40.64) 03309005
1.50”-1.74” (3.81-4.42) 4,000 (17,792) 9” (22.86) 17” (43.18) 03309006
1.75”-1.99” (4.44-5.05) 4,000 (17,792) 10” (25.40) 18” (45.72) 03309007
2.00”-2.49” (5.08-6.32) 4,000 (17,792) 10” (25.40) 19” (48.26) 03309008
2.50”-2.99” (6.35-7.59) 4,000 (17,792) 10” (25.40) 20” (50.80) 03309009
Long
1.50”-1.99” (3.81-5.05) 4,000 (17,792) 9” (22.86) 25” (63.50) 03309015
2.00”-2.49” (5.08-6.32) 4,000 (17,792) 10” (25.40) 26” (66.04) 03309016
2.50”-2.99” (6.35-7.59) 4,000 (17,792) 10” (25.40) 29” (73.66) 03309017
3.00”-3.49” (7.62-8.86) 4,000 (17,792) 12” (30.48) 32” (81.28) 03309018
3.50”-3.99” (8.89-10.13) 4,000 (17,792) 12” (30.48) 35” (88.90) 03309019
Slack Grip-Split Mesh, Rod Closing,
Single Eye, Single Weave, Galvanized Steel
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.61” (1.27-1.55) 1,500 (6,672) 7” (17.78) 6” (15.24) 03310001
.62”-.74” (1.57-1.88) 1,800 (8,006) 7” (17.78) 8” (20.32) 03310002
.75”-.99” (1.90-2.51) 2,200 (9,786) 7” (17.78) 10” (25.40) 03310003
1.00”-1.24” (2.54-3.15) 3,400 (15,123) 8” (20.32) 12” (30.48) 03310004
1.25”-1.49” (3.17-3.78) 4,500 (20,016) 8” (20.32) 14” (35.56) 03310005
1.50”-1.74” (3.81-4.42) 5,800 (25,798) 9” (22.86) 15” (38.10) 03310006
1.75” -1.99” (4.44-5.05) 7,600 (33,805) 10” (25.40) 16” (40.64) 03310007
2.00”-2.49” (5.08-6.32) 9,000 (40,032) 10” (25.40) 19” (48.26) 03310008
2.50”-2.99” (6.35-7.59) 11,000 (48,928) 10” (25.40) 20” (50.80) 03310009
3.00”-3.49” (7.62-8.86) 12,000 (53,376) 12” (30.48) 21” (53.34) 03310010
3.50”-3.99” (8.89-10.13) 12,000 (53,376) 12” (30.48) 24” (60.96) 03310011
E-Eye length M-Mesh length at nominal diameter
Note: Refer to page T-26 for multiple cables in a single pulling grip.
T-11
Dimensions in Inches (mm) www.hubbell-wiring.com
EM
EM
Pulling Grips Wire Management Products
Pulling Grips
Low Tension
Flexible Eye, Single Weave, Galvanized Steel
T-12 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-17 through T-
27.
Light Duty Pulling Grips are made
of galvanized steel in a single
weave construction. They feature a
flexible eye for easy attachment to
a pulling line.
Junior Pulling Grips feature a strong
galvanized steel, single weave
mesh. A flexible eye easily attaches
to
a pulling line, snake or fish
tape.
Junior Grip Kit
Junior Grip Kit contains 6 grips, one of
each size. Catalog number 033051114.
Note: Refer to page T-27 for
building wire selection chart.
Note: Refer to page T-26 for multiple
cables in a single pulling grip.
Light Duty Grips
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm.) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
Short
.50”-.61” (1.27-1.55) 2,800 (12,454) 5” (12.70) 11” (27.94) 03303001
.62”-.74” (1.57-1.88) 2,800 (12,454) 5” (12.70) 11” (27.94) 03303002
.75”-.99” (1.90-2.51) 4,000 (17,792) 6” (15.24) 12” (30.48) 03303003
1.00”-1.24” (2.54-3.15) 5,300 (23,574) 7” (17.78) 13” (33.02) 03303004
1.25”-1.49” (3.17-3.78) 5,300 (23,574) 7” (17.78) 14” (35.56) 03303005
1.50”-1.74” (3.81-4.42) 6,800 (30,246) 8” (20.32) 15” (38.10) 03303006
1.75”-1.99” (4.44-5.05) 8,500 (37,808) 9” (22.86) 17” (43.18) 03303007
2.00”-2.49” (5.08-6.32) 8,500 (37,808) 9” (22.86) 18” (45.72) 03303008
Standard
.50”-.61” (1.27-1.55) 2,800 (12,454) 5” (12.70) 16” (40.64) 03303010
.62”-.74” (1.57-1.88) 2,800 (12,454) 5” (12.70) 16” (40.64) 03303011
.75”-.99” (1.90-2.51) 4,000 (17,792) 6” (15.24) 20” (50.80) 03303012
1.00”-1.24” (2.54-3.15) 6,800 (30,246) 7” (17.78) 20” (50.80) 03303013
1.25”-1.49” (3.17-3.78) 6,800 (30,246) 7” (17.78) 21” (53.34) 03303015
1.50”-1.99” (3.81-5.05) 6,800 (30,246) 8” (20.32) 23” (58.42) 03303016
2.00”-2.49” (5.08-6.32) 8,500 (37,808) 9” (22.86) 25” (63.50) 03303017
2.50”-2.99” (6.35-7.59) 10,600 (47,149) 9” (22.86) 27” (68.58) 03303018
3.00”-3.49” (7.62-8.86) 14,700 (65,386) 10” (25.40) 30” (76.20) 03303019
3.50”-3.99” (8.89-10.13) 14,700 (65,386) 10” (25.40) 32” (81.28) 03303029
Junior Pulling Grips
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Model Numbers
.19”-.24” (.48-.61) 400 (1,779) 31/4” (8.25) 41/4” (10.79) J19 03305011*
.25”-.36” (.63-.91) 450 (2,002) 31/4” (8.25) 41/4” (10.79) J25 03305001
.37”-.49” (.94-1.24) 900 (4,003) 33/4” (9.52) 7” (17.78) J37 03305002
.50”-.61” (1.27-1.55) 1,300 (5,782) 41/4” (10.79) 81/2” (21.59) J50 03305003
.62”-.74” (1.57-1.88) 1,950 (8,674) 5” (12.70) 10” (25.40) J62 03305004
.75”-.99” (1.90-2.51) 2,800 (12,454) 53/4” (14.60) 10” (25.40) J75 03305005
1.00”-1.24” (2.54-3.15) 3,900 (17,347) 61/2” (16.51) 111/2” (29.21) J100 03305006
E-Eye length M-Mesh length at nominal diameter.
*Not included in Junior Grip Kit, 033051114.
ME
ME
Wire Management Products Pulling Grips
Splicing Grips
Wire Rope Splicing
Triple, Double, Single Weave, Galvanized Steel
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-17 through T-
27.
Kellems®Wire Rope Grips are
made of high strength galvanized
steel strand in a construction of
triple, double and single weave for
superior gripping ability. They are
available with or without a rotating
barrel which will help eliminate twist
in the old rope from being
transferred to the new rope.
Regular Wire Rope Grips
Cable Diameter Approx. Breaking Approx. Length Catalog
Range Inches (cm) Strength Lbs. (N) Of Grip Feet (m) Numbers
9/16
”-
5/8
” (1.43-1.59) 7,500 (33,360) 5.75 (1.75) 03316001
3/4
”-
7/8
” (1.90-2.22) 12,500 (55,600) 6.75 (1.90) 03316002
1”-1
1/8
” (2.54-2.86) 16,000 (71,168) 7.00 (2.13) 03316003
1
1/4
”- 1
3/8
” (3.17-3.49) 20,000 (88,960) 8.00 (2.44) 03316004
1
3/8
”- 1
1/2
” (3.49-3.81) 20,000 (88,960) 8.00 (2.44) 03316006
Rotating Wire Rope Grips
Cable Diameter Approx. Breaking Approx. Length Barrel Dimensions Catalog
Range (cm) Strength Lbs. (N) Of Grip Feet (m) Lgth. x O.D. Inches (cm) Numbers
7/16”- 1/2” (1.11-1.27) 5,000 (22,240) 5.33 (1.63) 3.00” (7.62) x .87” (2.21) 03317001
9/16”- 5/8” (1.43-1.59) 7,500 (33,360) 5.83 (1.78) 4.25” (10.79) x 1.00” (2.54) 03317002
3/4”- 7/8” (1.90-2.22) 12,500 (55,600) 6.50 (1.98) 4.25” (10.79) x 1.00” (2.54) 03317003
1”- 11/8” (2.54-2.86) 16,000 (71,169) 8.67 (2.64) 5.50” (13.97) x 1.37” (3.48) 03317004
11/4”- 13/8” (3.17-3.49)
20,000 (88,960) 9.00 (2.74) 5.50” (13.97) x 1.37” (3.48) 03317005
11/2”- 13/4” (3.81-4.44)
20,000 (88,960) 11.00 (3.35) 5.50” (13.97) x 1.37” (3.48) 03317006
T-13
Dimensions in Inches (mm) www.hubbell-wiring.com
Splicing Grips Wire Management Products
T-14 Dimensions in Inches (mm)
www.hubbell-wiring.com
Splicing Grips
Cable Splicing
Double Weave, Galvanized Steel / Single Weave, Galvanized Steel
Read This Data
It is important that you read all breaking
strength, safety and technical data
relating to this product on pages T-17
through T-27.
Splicing Grip
Splicing Grips are made of
galvanized steel in double weave
mesh construction. They are
available in various lengths and
sizes to suit most applications.
Double Weave Tube
Cable Diameter Range
Inches .37”-.49” .50”-.61” .62”-.74” .75”-.99” 1.00”-1.49”
(cm) (.94-1.24) (1.27-1.55) (1.57-1.88) (1.90-2.51) (2.54-3.78)
Approx. Breaking Strength
Lbs.
3,500 3,500 4,400 7,500 10,000
(N)
(15,568) (15,568) (19,571) (33,360) (44,480)
Mesh Length Catalog
Inches (cm) Numbers
18
”
(45.72) 013041330 01304064 01304009 ••
24
”
(60.96) • 01304011 01304013 01304010 01304015
36
”
(91.44) • • 013041234 01304054 01304055
48
”
(121.92) • • • 01304017 01304029
72
”
(182.88) • • • 01304037 013041333
Junior Splicing Grips,
Single Weave
Junior Splicing Grips are made of
galvanized steel and are designed
for use in very light duty and small
splicing jobs.
Junior Tube
Cable Diameter Approx. Breaking Length @ Nom Catalog
Range Inches (cm) Strength Lbs. (N) Diameter Inches (cm) Numbers
.18”-.24” (.49-.61) 400 (1,779) 7
”
(17.78) 01301008
.25”-.36” (.63-.91) 400 (1,779) 8
”
(20.32) 01301013
Wire Management Products Bands & Tools
T-15
Dimensions in Inches (mm) www.hubbell-wiring.com
Accessories
Tools and Bands
Punch-Lok®Bands
Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from
being tripped or pulled loose. Also, they assure full gripping action by locking
the mesh of the tail in tight contact with the cable or rope.
Punch-Lok Bands
Grip Banding Band Width Band Inside Catalog
Range Inches (cm) Inches (cm) Diameter Inches (cm) Model Numbers
1/4 “-11/8” (.63-2.86) 3/8” (.95) 13/8” (3.49) 0-311 20320050
11/8”-15/8” (2.86-4.13) 3/8” (.95) 2” (5.08) 0-316 20320051
15/8”-21/4” (4.13-5.71) 5/8” (1.59) 21/2” (6.35) 0-10 20320052
21/4”-31/2” (5.71-8.89) 5/8” (1.59) 4” (10.16) 0-16 20320053
31/2”-5” (8.89-12.70) 5/8” (1.59) 6” (15.24) 0-24 20320054
Accessories
Punch-Lok Tools
Catalog
Description Numbers
P-1 Heavy Duty. 20320048
P-38 Light Duty. 20320047
®Punch-Lok is a registered trademark of Punch-Lok Inc.
Swivels & Links Wire Management Products
T-16 Dimensions in Inches (mm)
www.hubbell-wiring.com
Accessories
Swivels and Links
Read This Data
It is important that you read all breaking
strength, safety and technical data relating to
this product on pages T-17 through T-27.
Swivels
Swivels are essential to the
efficiency and safety of any high
tension application. They are
particularly important where
continuous pulls develop higher and
higher torque levels. Torque is
intensified by the pull-resistance of
the cable itself and the resistance of
the high tension controlling
equipment regulating line sag.
Ball bearing swivels release torque
and prevent it from reaching danger-
ous levels that can damage the cable
and obstruct the lines as it passes
through sheaves, wheels or blocks.
Swivels
Approx. Breaking
Strength Dimensions in Inches (cm) Catalog
Lbs. (N) A B C D E F G Model Numbers
5,400 (24,019) 7/8” (2.22) 211/32” (5.95) 33/32” (7.86) 3/8” (.95) 5/16” (.79) 5/16” (.79) 15/32” (1.19) A-13L 20308001
12,000 (53,376) 11/4” (3.17) 321/32” (9.29) 411/32” (9.29) 7/16” (1.11) 19/32” (1.51) 3/8” (.95) 11/16” (1.75) BB-13L 20308002
22,500 (100,080) 17/16” (3.65) 4” (10.16) 51/8” (13.02) 9/16” (1.43) 19/32” (1.51) 7/16” (1.11) 13/16” (2.06) B-13L 20308003
30,000 (133,440) 17/8” (4.76) 57/16” (13.81) 71/16” (17.94) 13/16” (2.06) 3/4” (1.90) 5/8” (1.59) 15/16” (2.38) C-13L 20308004
48,000 (213,504) 27/16” (6.19) 77/8” (20.00) 103/16” (25.88) 11/8” (2.86) 1” (2.54) 7/8” (2.22) 19/16” (3.97) D-13L 20308005
Links
The bullet nose Link, with clevises
at 90°, provides a fast, economical
method of connecting pulling lines.
The result is a reliable pulling line
connector with adequate load
ratings for the tensions employed in
line stringing.
Because of its shorter length, the
Link contoured bullet nose
connector is able to pass through
stringing sheaves smoothly and
easily without damage.
Links
Approx. Breaking
Strength Dimensions in Inches (cm) Catalog
Lbs. (N) A B C D E F G Model Numbers
5,400 (24,019) 7/8” (2.22) 15/16” (3.33) 21/16” (3.33) 3/8” (.95) 5/16” (.79) 5/16” (.79) 15/32” (1.19) PL-1/4 093011037
12,000 (53,376) 11/4” (3.17) 13/4” (4.44) 25/8” (6.67) 7/16” (1.11) 19/32” (1.51) 3/8” (.95) 11/16” (1.75) PL-3/8 093011038
C
B
A
F
E
G
D
20308001
093011037
Wire Management Products Technical Data
Kellems®Pulling Grips
Technical Section
Kellems Pulling Grips are reusable tools for pulling electrical cable, bare
conductor or rope. They are easy and fast to install, providing the user with a
smooth, slim profile that allows for easy passage through ducts, conduit,
blocks and sheaves. Kellems Pulling Grips are made of the highest quality
galvanized steel strand which assures the user of a long lasting grip. There is
a Kellems Pulling Grip for every pulling job.
Select The Correct Pulling Grip
Each Kellems Grip is designed to work on a specific range of cable diameters.
Step 1 Refer to the chart below to determine the style of grip best suited for your
application.
Step 2 Determine your cable outside diameter.
Step 3 Find the grip size that encompasses your cable diameter.
Step 4 Estimate the tension to be put on the grip, establish the working load you
require and compare this to the listed approximate breaking strength of the
grip to insure that the grip will be strong enough. Refer to page T-18 for safety
and working load factors.
Pulling Grip Selection Chart
Page
Grip Style Application Numbers
DUA-PULL®, flexible eye Extra high strength overhead transmission line stringing for bare or
insulated conductor and synthetic rope. T-6
Multiple strength, flexible eye Normal overhead transmission and distribution line stringing, for bare or
insulated conductor. T-7
Multiple strength, forged eye Normal overhead transmission and distribution line stringing, for bare or
insulated conductor. T-7
K-type grip, forged eye Underground power cables and communication lines. Service lines into factories. T-8
T-type grip, flexible eye Underground power cables and communication lines. Service lines into factories. T-9
Non-conductive flexible eye Pull insulated distribution cable into place. T-10
Universal slack, closed mesh Remove underground cable. For pulling slack in final placement of
new cable when end of cable is available. T-10
Universal slack split mesh, Remove underground cable. For pulling slack in final placement of
rawhide lace closing new cable when end of cable is not available. T-11
Universal slack, split mesh, Remove underground cable. For pulling slack in final placement of
rod closing new cable when end of cable is not available, with rod closing for quick installation. T-11
Light duty, flexible eye Light pulling, underground electrical construction. Industrial plant
wiring and rewiring jobs. T-12
Junior, flexible eye Connect bundled insulated building wire to a pulling tape. Pull wire through conduit. T-12
Regular and rotating wire rope Restring wire rope in cranes and oil rigs. T-13
Splicing Temporary splice for cable or wire rope. T-14
Accessories Tools, bands, swivels, links. T-15, T-16
Fiber Optic Cable Pulling Grips Pull fiber optic cable into place overhead, underground or through duct and conduit. T-50, T-51, T-52
T-17
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Kellems®Pulling Grips
Technical Section
Safety And Working Load Factors For Wire Mesh Grips
T-18 Dimensions in Inches (mm)
www.hubbell-wiring.com
The broad application of Kellems grips on a wide
variety of objects requires that adequate safety
factors be used to establish working loads. The
approximate breaking strength of a Kellems grip
represents an average calculation based on data
established from actual direct tension testing done
in our engineering laboratories.
It is impossible to catalog or guarantee a safety
factor suitable for all applications as operating
conditions are never the same. The tension,
diameter, movement, number of objects gripped,
gripping surface, and the attachments used are just
some of the factors which vary with each
application. These factors, together with the effects
of abrasion, corrosion, prior use or abuse and any
other variables of a specific application, must be
considered by the user and the grip replaced as
appropriate. Where the conditions of the
application are not well defined or known, or where
risk of injury to persons or property is involved, a
greater safety factor should be utilized.
Under normal conditions, Kellems’
recommended factor of safety is five for catalog
listed pulling grips, and ten for catalog listed
support grips. The factory should be consulted
for specific application recommendations where
strength and holding power are important
factors.
Any warranty as to quality, performance or fitness
for use of grips is always premised on the condition
that the published breaking strengths apply only to
new, unused grips, and that such products are
properly stored, handled, used, maintained and
inspected by the user at a frequency appropriate
for the use and condition of the grip.
Examples
Approx. Breaking Safety Max. Rec. Catalog
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Numbers
Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027
Support Grips 1,610 (7,161) 10 161 (716) 02201018
The maximum recommended working load then is the tension to be exerted on the grip in application with
a margin of safety to take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable to him.
The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons
to the metric unit of weight (kilograms) the conversion factor is 9.808 newtons/kilogram.
Pulling Grip Materials
Material Features Product Group
Galvanized steel wire High strength Pulling Grip
Not subject to continuous
outside environment Wire rope grips
Splicing grips
Non-metallic strand Superior flex life Non-conductive pulling grips
Non-conductive
Corrosion resistant
Moderate strength
Approvals
CSA Certification is indicated on appropriate product catalog pages.
Wire Management Products Technical Data
Kellems®Pulling Grips
Technical Section
Overhead Pulling DUA-PULL®Grips
DUA-PULL Pulling Grips are the highest strength pulling grips manufactured for
overhead transmission line stringing applications. They have a dual function
of working with both bare and insulated conductors and synthetic rope, not
provided by any other grip.
Kellems’ patented two-over, two-under weave design gives exceptional
strength and gripping ability by putting more steel mesh in contact
with the cable or rope surfaces.
THIS IS THE ONLY PULLING GRIP RECOMMENDED FOR USE ON SYNTHETIC ROPE.
Application
The DUA-PULL Grips are primarily used in overhead transmission line
construction where loads and safety considerations require an extra high
strength grip. They are most commonly used for attaching pulling lines to
conductors, conductors to running boards and “double socking” for conductor-
to-conductor connections. The DUA-PULL line accommodates ACSR, ACAR, all
aluminum and copper conductors. Also, the grips accommodate ground wires,
messenger strands, wire ropes and synthetic ropes.
Benefits
• Made of high strength galvanized steel strand.
• Recommended for pulling bare or insulated conductor, wire rope and
synthetic rope.
• DUA-PULL mesh design offers the greatest holding power for all pulling
applications.
• Each grip size is color coded for fast and accurate identification and
selection.
• Will mate with swivels and link-type connectors. See page T-16.
Feed Tubes
The Kellems Feed Tube is used when assembling synthetic rope into the
DUA-PULL Grip. It is required on the largest two sizes of DUA-PULL Grips.
Feed
Tubes are available for use on all size DUA-PULL Grips.
Benefits
• Saves time, allowing fast, easy assembly.
• No special skills required.
• Completely reusable.
Notes: 1. Do not run grips or swivels over bullwheels while under tension.
2. Two Punch-Lok®bands should be firmly attached approximately one inch and two
inches (2.54cm and 5.08cm) from the grip’s tail. Banding is required to ensure
maximum reliability and guard against accidental release. See page T-15.
3. Double braided rope, as 2-in-1 type, should be back spliced for approximately 2/3of
the mesh length for best gripping results. Grip size should be selected by diameter of
back splice.
T-19
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Kellems®Pulling Grips
Technical Section
Overhead Pulling Multiple Strength Grips
Multiple Strength Pulling Grips are designed for pulling ACSR, aluminum or
copper bare conductor, ground wires, messenger strands, wire rope and
insulated cables. They are made of high strength galvanized steel strand and
feature a multi-weave mesh construction of single, double and triple weave
for firm holding power.
Application
Kellems Multiple Strength Grips are ideal for overhead transmission and
distribution line stringing where moderate loading is anticipated. They are
economical tools for attaching conductors to pulling lines and double
socking for conductor-to-conductor connections.
Rotating Eye Feature
Multiple Strength Grips are available with a forged steel rotating eye which
can be attached to a swivel. The forged eye is durable, compact and stream-
lined and will thread through blocks and sheaves without binding. The rotating
eye is not a swivel and will not turn while under tension; It can turn to relieve
pulling torque when tension is relaxed. If constant swivel action is required, a
swivel should be used. For rotating eye dimensions, see page T-21. Swivels
see page T-16.
Flexible Eye Feature
Multiple Strength Grips are also available with a flexible, patented wire rope eye.
This compact eye will mate with a swivel, and pass through blocks and sheaves
without binding.
Benefits
• Economical, high strength pulling tool.
• Multi-weave construction provides greater strength and holding power.
• Endless Weave Grip end lies flat on the cable and will not snag.
Notes: 1. Do not run grips or swivels over bullwheels while under tension.
2. Two Punch-Lok®bands should be firmly attached approximately one inch and two
inches (2.54cm and 5.08cm) from the grip’s tail. Banding is required to ensure
maximum reliability and guard against accidental release. See page T-15.
T-20 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Kellems®Pulling Grips
Technical Section
Underground Pulling- K-Type and T-Type Grips
K-Type Application
Rotating Eye, K-Type Pulling Grips are specially designed for use in the
installation of underground power cables, communication lines and service
lines into factories, shopping centers, construction projects and general
underground electrical construction.
Rotating Eye Feature
K-Type Grips come equipped with a forged steel rotating eye which can be
attached to a swivel. The forged eye is durable, compact and streamlined,
and will thread through blocks and sheaves without binding. The rotating eye
is not a swivel and will not turn while under tension; it can turn to relieve
pulling torque when the tension is relaxed. If constant swivel action is
required, a swivel should be used. For swivels, see page T-16.
Benefits
• An economical tool for pulling cable.
• Safe, rugged and dependable.
• Equipped with a rotating eye for spin out of pulling torque after load release.
• Easily installed and removed.
Rotating Eye Dimensions
Rotating Eye
Dimensions
inches (cm) A B C D F
7/8” (2.22) 7/8” (2.22) 9/32” (2.06) 1/2” (1.27) 7/8” (2.22) 25/8” (6.67)
1” (2.54) 1” (2.54) 1/2” (1.27) 9/16” (1.43) 13/16” (2.06) 31/2” (8.89)
13/8” (3.49) 13/8” (3.49) 1/2” (1.27) 111/16” (1.75) 1” (2.54) 41/2” (11.43)
15/8” (4.13) 15/8” (4.13) 5/8” (1.59) 7/8” (2.22) 13/16” (3.02) 55/16” (13.49)
17/8” (4.76) 17/8” (4.76) 21/32”(1.67) 1” (2.54) 13/8” (3.49) 61/8” (15.56)
T-Type
Kellems Flexible T-Type Pulling Grips are made of high strength galvanized
steel strand. They feature double weave mesh for positive holding power in
medium to heavy pulling jobs. The grip eye will easily attach to a swivel.
Application
T-Type Pulling Grips are used for the installation of underground power
cables, communication lines and service lines into factories, construction
projects and for general underground electrical construction. Available in two
mesh lengths, short for medium pulls, and standard for general purpose
pulling.
Benefits
• Will pull a single cable or cable bundles.
• Patented flexible eye design provides flexibility to follow line of pull.
• A dependable, reusable pulling tool.
• Easily installed and removed.
• Mates easily with a swivel. See page T-16.
T-21
Dimensions in Inches (mm) www.hubbell-wiring.com
F
D
A
3/16 R.
1/8 R.
C
B
Technical Data Wire Management Products
Kellems®Pulling Grips
Technical Section
Special Purpose Grips
Non-Conductive Pulling Grips
Kellems Non-Conductive Pulling Grips, made of a high strength, non-
conductive aramid fiber, are available for pulling single cable or cable
bundles. Their braided double weave design adds strength and positive
holding power.
Application
Kellems Non-Conductive Pulling Grips were developed for use
by utilities for pulling overhead distribution lines in close proximity to
energized lines and hardware.
Benefits
• Color coded for fast on-site selection.
• Extra flexibility for easy installation.
• Non-metallic mesh provides for safe pulls over “hot” areas.
• Pellethane jacketed aramid fiber mesh resists abrasion.
• Grips are corrosion resistant.
Notes: Taping is required to guard against accidental release and to insure maximum reliability.
Apply vinyl plastic electrical tape starting 2” to 3” (5.08cm to 7.62cm) from the tail of the grip
onto 2” to 3” (5.08cm to 7.62cm) of cable.
Slack Pulling Grips
Slack Pulling Grips are offered in three styles made of galvanized steel. The
closed type is used when the cable end is accessible. When not, there are
split lace and split rod closing styles. All grips feature single offset eye for
easy attachment to a pulling line.
Application
Slack Grips are widely used in pulling slack for final placement of under-
ground cable after it has been pulled in. They are also used for removing
cable. Standard mesh lengths are generally used in restricted space for short
pulls. Longer lengths are used for higher pulling loads where space is not
restricted.
Benefits
• Easy attachment to pulling lines.
• Reusable rawhide lace for lace closure.
• Galvanized steel for strength.
Notes: 1. Replacement rawhide lace. Catalog number 20920002.
2. See page T-47 for lace and rod closing instructions.
T-22 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Kellems®Pulling Grips
Technical Section
Commercial Construction/Light Duty Grips
Light Duty Pulling Grips
Light Duty Pulling Grips are made of galvanized steel in a single weave
construction. They feature a flexible eye for easy attachment to a pulling line.
Application
Light duty grips are used in general underground electrical construction
where pulling tensions are low. They are easy tools to use in wiring industrial
plants and commercial buildings.
Benefits
• Perfect tools for light pulling jobs.
• Installs easily on cable.
• Strong, galvanized steel construction.
Junior Duty Pulling Grips
Junior Pulling Grips feature a strong galvanized steel, single weave mesh. A
flexible eye easily attaches to a pulling line, snake or fish tape.
Application
Designed to pull building wire, Junior grips are safe tools to use in pulling wire
at low tension through conduit during electrical construction.
Benefits
• Installs easily over building wire.
• Strong secure grip.
• Reusable.
• Pulls single cable or cable bundles.
Junior Grip Kit
Junior Grip Kit contains 6 grips, one of each size.
Catalog number 033051114.
Note: Refer to page T-27 for building wire selection chart.
T-23
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Kellems®Pulling Grips
Technical Section
Splicing Grips
Wire Rope Splicing
Kellems Wire Rope Grips are made of high strength galvanized steel strand in a
construction of triple, double and single weave for superior gripping ability. They
are available with or without a rotating barrel which will help eliminate twist in the
old rope from being transferred to the new rope.
Application
Wire Rope Grips are used for changing wire rope on oil derricks, large cranes,
overhead cranes and drag lines. It provides a quick, safe, inexpensive temporary
splice. By installing the used wire rope in one end and the new rope in the other,
the new wire rope can be pulled in as the old one is pulled out.
Benefits
• High strength for secure pulling.
• Easy installation.
• Flexible to pass through sheaves and blocks.
Notes: 1. During installation each end of the grip should be banded over the rope to
insure smooth passage through sheaves and to guard against accidental
release. See page T-15 for end bands.
2. The rotating barrel is not a swivel and will not turn while under tension. It can turn
to relieve pulling torque when tension is relaxed.
Cable Splicing
Splicing Grips are made of galvanized steel in double or single weave mesh
construction. They are available in various lengths and sizes to suit most
applications.
Application
Splicing Grips are used as a temporary splice for rope, cable or wire rope. They
can also be used as cable reinforcement, and can act as a shield to protect
cables and hoses from abrasion.
Benefits
• Easily installed or removed.
• Galvanized steel construction for strength.
• Flexible to follow cable path.
Notes 1. During installation, each end of the splicing grip should be taped down securely to
the cable to in-sure smooth passage with the cable and guard against accidental
release.
2. See page T-15 for end bands.
T-24 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Kellems®Pulling Grips
Technical Section
Accessories
Punch-Lok®Bands
Punch-Lok Bands are applied over the tail of a grip to prevent the mesh from
being tripped or pulled loose. Also, they assure full gripping action by locking
the mesh of the tail in tight contact with the cable or rope.
When the tail of a grip is the leading end, the bands are particularly important
to prevent accidental release caused by tripping on obstructions. A
conductor-to-conductor (double-socking) pulling operation is a good example:
where two grips connect two conductors to form a temporary splice. Bands
should be applied to the ends of the grips as illustrated herein. It is also
common practice to tape over the banded tail area to assure smooth
passage through the sheaves.
The conductor should be installed in the grip up to the elbows of the
aluminum shoulders in order to assure full and complete gripping action. The
banding procedure is then followed as illustrated on page T-15.
Note: In all cases two Punch-Lok Bands should be double wrapped approximately
one inch to two inches (2.54cm to 5.08cm) from the grip’s tail. Banding
is required to ensure maximum reliability and guard against accidental release.
Swivels
Swivels are essential to the efficiency and safety of any high tension
application. They are particularly important where continuous pulls develop
higher and higher torque levels. Torque is intensified by the pull-resistance of
the cable itself and the resistance of the high tension controlling equipment
regulating line sag.
Ball bearing swivels release torque and prevent it from reaching dangerous
levels that can damage the cable and obstruct the lines as it passes through
sheaves, wheels or blocks.
®Punch-Lok is a registered trademark of Punch-Lok Inc.
T-25
Dimensions in Inches (mm) www.hubbell-wiring.com
T-26 Dimensions in Inches (mm)
www.hubbell-wiring.com
Technical Data Wire Management Products
Kellems®Pulling Grips
Technical Section
Multiple Cable Selection Charts for Cables of Equal Diameters
For Pulling Grips*
Caution: When a grip is used on multiple cables, the tail end of the grip should be
banded or tightly taped after positioning on the cables.
For Cables of Equal Diameters
Under “Number of Cables in One Grip,” find diameter of your single cable in vertical
column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for
Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .89” (2.26cm) diameter, for a Closed Grip select
the 1.50”-1.74” (3.81cm-4.42cm) range, for a Split Grip select the
1.75”-1.99” (4.44cm-5.05cm) range.
Number of Cables in One Grip
Grip Dia. Range
2 3 4 5 6 and 7 8 9 Inches (cm)
.30-.38 .25-.31 .22-.27 .19-.24 .17-.22 .15-.19 .14-.18 .50-.61
(.76-.97) (.63-.79) (.56-.69) (.48-.61 ) (.43-.56) (.38-.48) (.36-.46) (1.27-1.55)
.38-.44 .31-.36 .27-.31 .24-.29 .22-.26 .19-.23 .18-.21 .62-.74
(.97-1.12) (.79-.91) (.69-.79) (.61-.74) (.56-.66) (.48-.56) (.46-.53) (1.57-1.88)
.44-.59 .36-.49 .31-.42 .29-.38 .26-.34 .23-.31 .21-.28 .75-.99
(1.12-1.50) (.91-1.24) (.79-1.07) (.74-.97) (.66-.86) (.58-.79) (.53-.71) (1.90-2.51)
.59-.75 .49-.63 .42-.54 .38-.48 .34-.43 .31-.39 .28-.35 1.00-1.24
(1.50-1.90) (1.24-1.60) (1.07-1.37) (.97-1.22) (.86-1.09) (.79-.99) (.71-.89) (2.54-3.15)
.75-.90 .63-.76 .54-.65 .48-.58 .43-.52 .39-.46 .35-.42 1.25-1.49
(1.90-2.29) (1.60-1.93) (1.37-1.65) (1.22-1.47) (1.09-1.32) (.99-1.17) (.89-1.07) (3.17-3.78)
.90-1.07 .76-.89 .65-.77 .58-.67 .52-.60 .46-.54 .42-.49 1.50-1.74
(2.29-2.72) (1.93-2.26) (1.65-1.96) (1.47-1.70) (1.32-1.52) (1.17-1.37) (1.07-1.24) (3.81-4.42)
1.07-1.22 .89-1.02 .77-.88 .67-.77 .60-.69 .54-.62 .49-.56 1.75-1.99
(2.72-3.10) (2.26-2.59) (1.96-2.24) (1.70-1.96) (1.52-1.75) (1.37-1.57) (1.24-1.42) (4.44-5.05)
1.22-1.53 1.02-1.28 .88-1.10 .77-.96 .69-.86 .62-.77 .56-.71 2.00-2.49
(3.10-3.89) (2.59-3.25) (2.24-2.79) (1.96-2.44) (1.75-5.54) (1.57-1.96) (1.42-1.80) (5.08-6.32)
1.53-1.83 1.28-1.53 1.10-1.32 .96-1.16 .86-1.03 .77-.93 .71-.85 2.50-2.99
(3.89-4.65) (3.25-3.89) (2.79-3.35) (2.44-2.95) (2.18-2.62) (1.96-2.36) (1.80-2.16) (6.35-7.59)
1.83-2.14 1.53-1.79 1.32-1.54 1.16-1.35 1.03-1.20 .93-1.08 .85-.99 3.00-3.49
(4.65-5.44) (3.89-4.55) (3.35-3.91) (2.95-3.43) (2.62-3.05) (2.36-2.74) (2.16-2.51) (7.62-8.86)
2.14-2.44 1.79-2.05 1.54-1.76 1.35-1.54 1.20-1.37 1.08-1.24 .99-1.13 3.50-3.99
(5.44-6.20) (4.55-5.21) (3.91-4.47) (3.43-3.91) (3.05-3.48) (2.74-3.15) (2.51-2.87) (8.89-10.13)
2.44-2.75 2.05-2.30 1.76-1.98 1.54-1.74 1.37-1.55 1.24-1.39 1.13-1.27 4.00-4.49
(6.20-6.98) (5.21-5.84) (4.47-5.03) (3.91-4.42) (3.48-3.94) (3.15-3.53) (2.87-3.23) (10.16-11.40)
2.75-3.06 2.30-2.56 1.98-2.20 1.74-1.93 1.55-1.72 1.39-1.55 1.27-1.41 4.50-4.99
(6.98-7.77) (5.84-6.50) (5.03-5.59) (4.42-4.90) (3.94-4.37) (3.53-3.94) (3.23-3.58) (11.43-12.67)
*This chart is not to be used for Conduit Riser Grips. Refer to the chart for Conduit Riser multiple cable section.
Note: It is always recommended that, when multiple cables are installed in a pulling grip, the tail end be banded and tightly taped
after installation on the cable bundle.
Wire Management Products Technical Data
Kellems®Pulling Grips
Technical Section
Junior Pulling Grip Selection Chart
These charts are a general guide to assist in the selection of the correct
Junior Pulling Grip for pulling various groupings of building wire. It is not
intended to be restrictive inasmuch as the use of “dummy” wires (short
pieces of wire used to fill out the Grip) or the tight taping of the wires into a
compact bundle may increase or decrease the number of wires per Grip.
T.H.W.N., T.H.H.N., X.H.H.W. Building Wire
#14 #12 #10 #8 #6 #4 #3 #2 #1 #1/0
19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 19 Strand 37 Strand 37 Strand
Cable Dia. Approx. Breaking
Range Strength Catalog
Desc. In. (cm) Lbs. (N) Approximate Number Of Wires In One Grip Numbers
J 25 .25-.36 450 4-8 3-6 2-3 2 1 1 1 • • • 03305001
(.63-.91) (2,002)
J 37 .37-.49 900 9-16 6-11 4-6 3 2 • • 1 1 1 03305002
(.94-1.24) (4,003)
J 50 .50-.61 1,300 16-25 11-17 7-10 4-5 3-4 2 2 • • • 03305003
(1.27-1.55) (5,782)
J 62 .62-.74 1,950 26-37 18-25 11-14 6-8 5-6 3 3 2 2 • 03305004
(1.57-1.88) (8,674)
J 75 .75-.99 2,800 37-66 26-47 15-27 9-16 6-11 4-7 4-5 3-4 3 2-3 03305005
(1.90-2.51) (12,454)
J 100 1.00-1.24 3,900 66-104 47-74 28-43 16-24 11-17 8-10 6-8 5-7 4-5 4 03305006
(2.54-3.15) (17,347)
R.H.H., R.H., R.W. and R.H.W. Building Wire
#14 #12 #10 #8 #6 #4 #2 #1 #1/0
7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 19 Strand 19 Strand
Cable Dia. Approx. Breaking
Range Strength Catalog
Desc. In. (cm) Lbs. (N) Approximate Number Of Wires In One Grip Numbers
J 25 .25-.36 450 2 2 1 1 • • • • • 03305001
(.63-.91) (2,002)
J 37 .37-.49 900 3 2-3 2 • 1 1 1 • • 03305002
(.94-1.24) (4,003)
J 50 .50-.61 1,300 4-5 4-5 3-4 2 • • • 1 • 03305003
(1.27-1.55) (5,782)
J 62 .62-.74 1,950 6-8 6-7 4-5 3 2 2 • • 1 03305004
(1.57-1.88) (8,674)
J 75 .75-.99 2,800 9-16 8-14 6-10 4-6 3-4 3-4 2-3 2 • 03305005
(1.90-2.51) (12,454)
J 100 1.00-1.24 3,900 16-24 15-22 11-16 7-10 5-7 4-6 4 3 2-3 03305006
(2.54-3.15) (17,347)
T.H.W. Building Wire
#14 #12 #10 #8 #6 #4 #2 #1 #1/0
7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 7 Strand 19 Strand
Cable Dia. Approx. Breaking
Range Strength Catalog
Desc. In. (cm) Lbs. (kg) Approximate Number Of Wires In One Grip Numbers
J 25 .25-.36 450 2-4 2-3 2 1 1 1 • • • 03305001
(.63-.91) (2,002)
J 37 .37-.49 900 5-7 4-5 3-4 2 • • 1 • • 03305002
(.94-1.24) (4,003)
J 50 .50-.61 1,300 8-11 6-8 5-7 3-4 2 2 • 1 1 03305003
(1.27-1.55) (5,782)
J 62 .62-.74 1,950 12-16 9-12 8-10 5-6 3-4 3 2 • • 03305004
(1.57-1.88) (8.674)
J 75 .75-.99 2,800 17-30 13-24 11-19 7-10 5-7 4-5 3-4 2 2 03305005
(1.90-2.51) (12,454)
J 100 1.00-1.24 3,900 31-48 25-37 20-30 11-17 8-11 6-8 5-6 3-4 3 03305006
(2.54-3.15) (17,347)
T-27
Dimensions in Inches (mm) www.hubbell-wiring.com
Kellems®Grips for Cable Support
Wire Management Products Support Grips
Kellems®Grips for Cable Support
Heavy Duty, Standard Duty, Light Duty
Tin-Coated Bronze/Stainless Steel
The positive action mesh grip is designed for light duty up to heavy duty.
Closed grips fit over the cable end, split grips wrap around the cable
mid-span. The standard material is nonmagnetic, tin-coated bronze.
Selected items are available in stainless steel. Contact the factory.
Solid eye assemblies provide eye reinforcement at support hardware.
Four eye styles available: single (shown), double, universal, and offset.
Identification tag shows: catalog number, diameter range, agency
approval, and bar code.
The strand equalizer positions wires for equal loading throughout the
entire grip length.
The endless weave provides easy installation onto cable, and can be
easily repositioned.
T-29
Dimensions in Inches (mm) www.hubbell-wiring.com
Support Grips Wire Management Products
Support Grips
Standard Duty Support
Double Eye, Single Weave, Tin-Coated Bronze
T-30 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through
T-48.
Double Eye, Closed Mesh
Double Eye, Split Mesh, Lace Closing
Double Eye, Split Mesh, Rod Closing
M
E
Double Eye, Split Mesh, Lace Closing
M
E
ouble Eye, Closed Mesh
E
M
Double Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 530 (2,357) 4” (10.16) 10” (25.40) 02201001
.63”-.74” (1.60-1.88) 790 (3,415) 4” (10.16) 10” (25.40) 02201002
.75”-.99” (1.90-2.51) 1,020 (4,537) 4” (10.16) 13” (33.02) 02201003
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 5” (12.70) 14” (35.56) 02201005
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 5” (12.70) 15” (38.10) 02201006
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 5” (12.70) 17” (43.18) 02201007
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 6” (15.24) 19” (48.26) 02201008
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 6” (15.24) 21” (53.34) 02201009
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 6” (15.24) 23” (58.42) 02201010
3.00”-3.49” (7.62-8.86) 4,900 (21,795) 8” (20.32) 25” (63.50) 02201011
3.50”-3.99” (8.89-10.13) 4,900 (21,795) 8” (20.32) 27” (68.58) 02201012
Double Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 530 (2,357) 4” (10.16) 10” (25.40) 02202001
.63”-.74” (1.60-1.88) 790 (3,415) 4” (10.16) 10” (25.40) 02202002
.75”-.99” (1.90-2.51) 1,020 (4,537) 4” (10.16) 13” (33.02) 02202003
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 5” (12.70) 14” (35.56) 02202005
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 5” (12.70) 15” (38.10) 02202006
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 5” (12.70) 17” (43.18) 02202007
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 6” (15.24) 19” (48.26) 02202008
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 6” (15.24) 21” (53.34) 02202009
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 6” (15.24) 23” (58.42) 02202010
3.00”-3.49” (7.62-8.86) 4,900 (21,795) 8” (20.32) 25” (63.50) 02202011
3.50”-3.99” (8.89-10.13) 4,900 (21,795) 8” (20.32) 27” (68.58) 02202012
Double Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 790 (3,415) 4” (10.16) 81/2” (21.59) 02203001
.63”-.74” (1.60-1.88) 790 (3,415) 4” (10.16) 81/2” (21.59) 02203002
.75”-.99” (1.90-2.51) 1,020 (4,537) 4” (10.16) 101/2” (26.67) 02203003
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 5” (12.70) 121/2” (31.75) 02203005
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 5” (12.70) 141/2” (36.83) 02203006
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 5” (12.70) 151/2” (39.37) 02203007
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 6” (15.24) 161/2” (41.91) 02203008
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 6” (15.24) 191/2” (49.53) 02203009
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 6” (15.24) 211/2” (54.61) 02203010
3.00”-3.49” (7.62-8.86) 5,750 (25,576) 8” (20.32) 231/2” (59.69) 02203011
3.50”-3.99” (8.89-10.13) 5,750 (25,576) 8” (20.32) 251/2” (64.77) 02203012
E-Eye length M-Mesh length at nominal diameter
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
Wire Management Products ?????
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through
T-48.
E
M
Single Eye, Split Mesh, Rod Closin
g
Single Eye, Split Mesh, Lace Closin
g
E
M
E
M
Single Eye, Closed Mesh
Single Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 530 (2,357) 7” (17.78) 10” (25.40) 02201013
.63”-.74” (1.60-1.88) 790 (3,514) 8” (20.32) 10” (25.40) 02201014
.75”-.99” (1.90-2.51) 1,020 (4,537) 8” (20.32) 13” (33.02) 02201015
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 9” (22.86) 14” (35.56) 02201017
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 10” (25.40) 15” (38.10) 02201018
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 12” (30.48) 17” (43.18) 02201019
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 14” (35.56) 19” (48.26) 02201020
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 16” (40.64) 21” (53.34) 02201021
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 18” (45.72) 23” (58.42) 02201022
3.00”-3.49” (7.62-8.86) 4,900 (21,795) 21” (53.34) 25” (63.50) 02201023
3.50”-3.99” (8.89-10.13) 4,900 (21,795) 24” (60.96) 27” (68.58) 02201024
Single Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 530 (2,357) 7” (17.78) 10” (25.40) 02202013
.63”-.74” (1.60-1.88) 790 (3,514) 8” (20.32) 10” (25.40) 02202014
.75”-.99” (1.90-2.51) 1,020 (4,537) 8” (20.32) 13” (33.02) 02202015
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 9” (22.86) 14” (35.56) 02202017
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 10” (25.40) 15” (38.10) 02202018
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 12” (30.48) 17” (43.18) 02202019
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 14” (35.56) 19” (48.26) 02202020
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 16” (40.64) 21” (53.34) 02202021
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 18” (45.72) 23” (58.42) 02202022
3.00”-3.49” (7.62-8.86) 4,900 (21,795) 21” (53.34) 25” (63.50) 02202023
3.50”-3.99” (8.89-10.13) 4,900 (21,795) 24” (60.96) 27” (68.58) 02202024
Single Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 790 (3,514) 7” (17.78) 81/2” (21.59) 02203013
.63”-.74” (1.60-1.88) 790 (3,514) 8” (20.32) 81/2” (21.59) 02203014
.75”-.99” (1.90-2.51) 1,020 (4,537) 8” (20.32) 101/2” (26.67) 02203015
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 9” (22.86) 121/2” (31.75) 02203017
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 10” (25.40) 141/2” (36.83) 02203018
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 12” (30.48) 151/2” (39.37) 02203019
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 14” (35.56) 161/2” (41.91) 02203020
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 16” (40.64) 191/2” (49.53) 02203021
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 18” (45.72) 211/2” (54.61) 02203022
3.00”-3.49” (7.62-8.86) 5,750 (25,576) 21” (53.34) 231/2” (59.69) 02203023
3.50”-3.99” (8.89-10.13) 5,750 (25,576) 24” (60.96) 251/2” (64.77) 02203024
E-Eye length M-Mesh length at nominal diameter
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
T-31
Dimensions in Inches (mm) www.hubbell-wiring.com
Dimensions in Inches (mm) www.hubbell-wiring.com
Wire Management Products Support Grips
Support Grips
Standard Duty Support
Single Eye, Single Weave, Tin-Coated Bronze
Support Grips Wire Management Products
Support Grips
Standard Duty Support
Offset Eye, Single Weave, Tin-Coated Bronze
T-32 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43
through T-48.
E
M
O
ffset Eye, Split Mesh, Rod Closing
E
M
O
ffset Eye, Split Mesh, Lace Closing
E
M
Offset Eye, Closed Mesh
Offset Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 500 (2,724) 4” (10.16) 10” (25.40) 02201037
.63”-.74” (1.60-1.88) 750 (3,336) 4” (10.16) 10” (25.40) 02201038
.75”-.99” (1.90-2.51) 950 (4,226) 4” (10.16) 13” (33.02) 02201039
1.00”-1.24” (2.54-3.15) 1,500 (6,672) 5” (12.70) 14” (35.56) 02201041
1.25”-1.49” (3.17-3.78) 1,500 (6,672) 5” (12.70) 15” (38.10) 02201042
1.50”-1.74” (3.81-4.42) 1,500 (6,672) 5” (12.70) 17” (43.18) 02201043
1.75”-1.99” (4.44-5.05) 2,000 (8,896) 6” (15.24) 19” (48.26) 02201044
2.00”-2.49” (5.08-6.32) 3,100 (13,789) 9” (22.86) 21” (53.34) 02201045
2.50”-2.99” (6.35-7.59) 3,100 (13,789) 9” (22.86) 23” (58.42) 02201046
3.00”-3.49” (7.62-8.86) 3,800 (16,902) 11” (27.94) 25” (63.50) 02201047
3.50”-3.99” (8.89-10.13) 3,800 (16,902) 11” (27.94) 27” (68.58) 02201048
Offset Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 500 (2,724) 4” (10.16) 10” (25.40) 02202037
.63”-.74” (1.60-1.88) 750 (3,336) 4” (10.16) 10” (25.40) 02202038
.75”-.99” (1.90-2.51) 950 (4,226) 4” (10.16) 13” (33.02) 02202039
1.00”-1.24” (2.54-3.15) 1,500 (6,672) 5” (12.70) 14” (35.56) 02202041
1.25”-1.49” (3.17-3.78) 1,500 (6,672) 5” (12.70) 15” (38.10) 02202042
1.50”-1.74” (3.81-4.42) 1,500 (6,672) 5” (12.70) 17” (43.18) 02202043
1.75”-1.99” (4.44-5.05) 2,000 (8,896) 6” (15.24) 19” (48.26) 02202044
2.00”-2.49” (5.08-6.32) 2,150 (9,563) 9” (22.86) 21” (53.34) 02202045
2.50”-2.99” (6.35-7.59) 2,150 (9,563) 9” (22.86) 23” (58.42) 02202046
3.00”-3.49” (7.62-8.86) 3,800 (16,902) 11” (27.94) 25” (63.50) 02202047
3.50”-3.99” (8.89-10.13) 3,800 (16,902) 11” (27.94) 27” (68.58) 02202048
Offset Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 500 (2,724) 4” (10.16) 7” (17.78) 02203037
.63”-.74” (1.60-1.88) 750 (3,336) 4” (10.16) 9” (22.86) 02203038
.75”-.99” (1.90-2.51) 950 (4,226) 4” (10.16) 10” (25.40) 02203039
1.00”-1.24” (2.54-3.15) 1,500 (6,672) 5” (12.70) 12” (30.48) 02203041
1.25”-1.49” (3.17-3.78) 1,500 (6,672) 5” (12.70) 14” (35.56) 02203042
1.50”-1.74” (3.81-4.42) 1,500 (6,672) 5” (12.70) 15” (38.10) 02203043
1.75”-1.99” (4.44-5.05) 2,000 (8,896) 6” (15.24) 16” (40.64) 02203044
2.00”-2.49” (5.08-6.32) 3,100 (13,789) 9” (22.86) 19” (48.26) 02203045
2.50”-2.99” (6.35-7.59) 3,100 (13,789) 9” (22.86) 20” (50.80) 02203046
3.00”-3.49” (7.62-8.86) 4,300 (19,126) 11” (27.94) 21” (53.34) 02203047
3.50”-3.99” (8.89-10.13) 4,900 (21,795) 11” (27.94) 21” (53.34) 02203048
E-Eye length M-Mesh length at nominal diameter
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
Wire Management Products Support Grips
Support Grips
Standard Duty Support
Universal Eye, Single Weave, Tin-Coated Bronze
Read This Data
It is important that you read all
breaking strength, safety and
technical data
relating to this product on pages
T-43 through T-48.
M
E
Dim. to
Sliding Bar
Fully Ext'd.
U
niversal Eye Split Mesh, Rod Closin
g
M
E
Dim. to
Sliding Bar
Fully Ext'd.
U
niversal Eye Split Mesh, Lace Closin
g
M
E
Dim. to
Sliding Bar
Fully Ext'd.
Universal Eye, Closed Mesh
Universal Eye, Closed Mesh*
For permanent support when cable end is available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 530 (2,357) 18” (45.72) 10” (25.40) 02201051
.63”-.74” (1.60-1.88) 790 (3,514) 18” (45.72) 10” (25.40) 02201052
.75”-.99” (1.90-2.51) 1,020 (4,537) 18” (45.72) 13” (33.02) 02201053
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 18” (45.72) 14” (35.56) 02201050
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 18” (45.72) 15” (38.10) 02201054
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 18” (45.72) 17” (43.10) 02201055
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 18” (45.72) 19” (48.26) 02201056
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 18” (45.72) 21” (53.34) 02201057
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 18” (45.72) 23” (58.42) 02201058
Universal Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 530 (2,357) 18” (45.72) 10” (25.40) 02202050
.63”-.74” (1.60-1.88) 790 (3,514) 18” (45.72) 10” (25.40) 02202051
.75”-.99” (1.90-2.51) 1,020 (4,537) 18” (45.72) 13” (33.02) 02202052
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 18” (45.72) 14” (35.56) 02202054
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 18” (45.72) 15” (38.10) 02202055
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 18” (45.72) 17” (43.10) 02202056
1.75”-1.99” (4.44-5.05) 2,150 (9,563) 18” (45.72) 19” (48.26) 02202057
2.00”-2.49” (5.08-6.32) 3,260 (14,500) 18” (45.72) 21” (53.34) 02202058
2.50”-2.99” (6.35-7.59) 3,260 (14,500) 18” (45.72) 23” (58.42) 02202059
3.00”-3.49” (7.62-8.86) 4,900 (21,795) 18” (45.72) 25” (63.50) 02202060
3.50”-3.99” (8.89-10.13) 4,900 (21,795) 18” (45.72) 27” (68.58) 02202061
Universal Eye, Split Mesh, Rod Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.50”-.62” (1.27-1.57) 790 (3,514) 18” (45.72) 81/2” (21.59) 02203064
.63”-.74” (1.60-1.88) 790 (3,514) 18” (45.72) 81/2” (21.59) 02203065
.75”-.99” (1.90-2.51) 1,020 (4,537) 18” (45.72) 101/2” (26.67) 02203066
1.00”-1.24” (2.54-3.15) 1,610 (7,161) 18” (45.72) 121/2” (31.75) 02203068
1.25”-1.49” (3.17-3.78) 1,610 (7,161) 18” (45.72) 141/2” (36.83) 02203069
1.50”-1.74” (3.81-4.42) 1,610 (7,161) 18” (45.72) 151/2” (39.37) 02203070
3.00”-3.49” (7.62-8.86) 5,750 (25,576) 18” (45.72) 231/2” (59.69) 02203074
E-Eye length M-Mesh length at nominal diameter
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
T-33
Dimensions in Inches (mm) www.hubbell-wiring.com
Support Grips Wire Management Products
Support Grips
Heavy Duty Support
Single Eye, Double Weave, Tin-Coated Bronze
T-34 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through
T-48.
M
E
S
ingle Eye, Split Mesh, Lace Closing
M
E
H
eavy Duty, Single Eye, Closed Mes
h
Heavy Duty, Single Eye, Closed Mesh*
For heavy duty permanent support when cable end is available to be installed
through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.75”-.99” (1.90-2.51) 2,820 (12,543) 10” (25.40) 25” (63.50) 02206010
1.00”-1.24” (2.54-3.15) 4,280 (19,037) 12” (30.48) 28” (71.12) 02206011
1.25”-1.49” (3.17-3.78) 4,280 (19,037) 12” (30.48) 30” (76.20) 02206012
1.50”-1.99” (3.81-5.05) 4,280 (19,037) 12” (30.48) 34” (86.36) 02206013
Single Eye, Split Mesh, Lace Closing*
For permanent support when cable end is not available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.75”-.99” (1.90-2.51) 2,820 (12,543) 10” (25.40) 25” (63.50) 02207010
1.00”-1.24” (2.54-3.15) 4,280 (19,037) 12” (30.48) 28” (71.12) 02207011
1.25”-1.49” (3.17-3.78) 4,280 (19,037) 12” (30.48) 30” (76.20) 02207012
1.50”-1.99” (3.81-5.05) 4,280 (19,037) 12” (30.48) 34” (86.36) 02207013
E-Eye length M-Mesh length at nominal diameter
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
Wire Management Products Support Grips
Support Grips
Heavy Duty Support
Double Eye, Double Weave, Tin-Coated Bronze
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through
T-48.
M
E
D
ouble Eye, Split Mesh, Lace Closin
g
M
E
D
ouble Eye, Closed Mesh
Double Eye, Closed Mesh*
For permanent support when cable end is not available to be installed through grip.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.75”- .99”(1.90-2.51) 2,820 (12,543) 10” (25.40) 25” (63.50) 02206001
1.00”-1.24” (2.54-3.15) 4,280 (19,037) 10” (25.40) 28” (71.12) 02206002
1.25”-1.49” (3.17-3.78) 4,280 (19,037) 10” (25.40) 30” (76.20) 02206003
1.50”-1.99” (3.81-5.05) 4,280 (19,037) 10” (25.40) 34” (86.36) 02206004
2.00”-2.49” (5.08-6.32) 8,050 (35,806) 12” (30.48) 36” (91.44) 02206005
2.50”-2.99” (6.35-7.59) 8,050 (35,806) 12” (30.48) 38” (96.52) 02206006
3.00”-3.49” (7.62-8.86) 10,060 (44,747) 12” (30.48) 40” (101.62) 02206007
3.50”-3.99” (8.89-10.13) 12,070 (53,687) 12” (30.48) 44” (111.76) 02206008
4.00”-4.49” (10.16-11.40) 12,070 (53,687) 12” (30.48) 46” (116.84) 02206009
4.50”-4.99” (11.43-12.67) 12,070 (53,687) 12” (30.48) 68” (172.72) 02208009
Double Eye, Split Mesh, Lace Closing*
For support when cable end is not available.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.75”-.99” (1.90-2.51) 2,820 (12,543) 10” (25.40) 25” (63.50) 02207001
1.00”-1.24” (2.54-3.15) 4,280 (19,037) 10” (25.40) 28” (71.12) 02207002
1.25”-1.49” (3.17-3.78) 4,280 (19,037) 10” (25.40) 30” (76.20) 02207003
1.50”-1.99” (3.81-5.05) 4,280 (19,037) 10” (25.40) 34” (86.36) 02207004
2.00”-2.49” (5.08-6.32) 8,050 (35,806) 12” (30.48) 36” (91.44) 02207005
2.50”-2.99” (6.35-7.59) 8,050 (35,806) 12” (30.48) 38” (96.52) 02207006
3.00”-3.49” (7.62-8.86) 10,060 (44,747) 12” (30.48) 40” (101.62) 02207007
3.50”-3.99” (8.89-10.13) 12,070 (53,687) 12” (30.48) 44” (111.76) 02207008
4.00”-4.49” (10.16-11.40) 12,070 (53,687) 12” (30.48) 46” (116.84) 02207009
4.50”-4.99” (11.43-12.67) 12,070 (53,687) 12” (30.48) 68” (172.72) 02209009
E-Eye length M-Mesh length at nominal diameter
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
T-35
Dimensions in Inches (mm) www.hubbell-wiring.com
Support Grips Wire Management Products
Support Grips
Service Drop
Single Eye, Tin-Coated Bronze
T-36 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through T-
48.
* Change catalog number from 022 to 024
for stainless steel. Consult factory for
availability..
M
E
H
eavy Duty, Single Eye, Closed Mes
h
M
E
L
ight Duty, Single Eye, Closed Mesh
Light Duty, Single Eye, Closed Mesh Single Weave*
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.23”-.31” (.58-.79) 290 (1,290) 3” (7.62) 33/4” (9.52) 02216001
.29”-.37” (.74-.94) 290 (1,290) 5” (12.70) 41/4” (10.79) 02216002
.35”-.44” (.89-1.12) 500 (2,224) 5.5” (13.97) 43/4” (12.06) 02216003
.41”-.50” (1.04-1.27) 500 (2,224) 5.5” (13.97) 5” (12.70) 02216004
.46”-.56” (1.17-1.42) 660 (2,936) 6” (15.24) 51/4” (13.33) 02216005
.52”-.62” (1.32-1.57) 790 (3,514) 7” (17.78) 61/4” (15.87) 02216006
.58”-.68” (1.47-1.73) 790 (3,514) 7” (17.78) 61/2” (16.51) 02216007
.64”-.75” (1.63-1.90) 790 (3,514) 7” (17.78) 63/4” (17.14) 02216008
.70”-.81” (1.78-2.06) 790 (3,514) 7” (17.78) 71/4” (18.41) 02216009
.75”-.87” (1.90-2.21) 1,020 (4,537) 8” (20.32) 8” (20.32) 02216010
.81”-.94” (2.06-2.39) 1,020 (4,537) 8” (20.32) 81/4” (20.95) 02216011
.87”-1.00” (2.21-2.54) 1,020 (4,537) 8” (20.32) 83/4” (22.22) 02216012
.94”-1.06” (2.39-2.69) 1,020 (4,537) 9” (22.86) 9” (22.86) 02216013
1.00”-1.18” (2.54-3.00) 1,020 (4,537) 9” (22.86) 91/2” (24.13) 02216014
1.06”-1.25” (2.69-3.17) 1,020 (4,537) 9” (22.86) 91/2” (24.13) 02216015
Heavy Duty, Single Eye, Closed Mesh Multi-Weave*
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.23”-.31” (.58-.79) 500 (2,224) 5” (12.70) 41/2” (11.43) 02217001
.29”-.37” (.74-.94) 500 (2,224) 5” (12.70) 51/2” (13.97) 02217002
.35”-.44” (.89-1.12) 870 (3,870) 6” (15.24) 61/2” (16.51) 02217003
.41”-.50” (1.04-1.27) 870 (3,870) 6” (15.24) 71/2” (19.05) 02217004
.46”-.56” (1.17-1.42) 1,050 (4,670) 6” (15.24) 8” (20.32) 02217005
.52”-.62” (1.32-1.57) 1,050 (4,670) 7” (17.78) 81/2” (21.59) 02217006
.58”-.68” (1.47-1.73) 1,050 (4,670) 7” (17.78) 91/2” (24.13) 02217007
.64”-.75” (1.63-1.90) 1,390 (6,183) 7” (17.78) 91/2” (24.13) 02217008
.70”-.81” (1.78-2.06) 1,390 (6,183) 8” (20.32) 101/2” (26.67) 02217009
.75”-.87” (1.90-2.21) 1,390 (6,183) 8” (20.32) 101/2” (26.67) 02217010
.81”-.94” (2.06-2.39) 1,390 (6,183) 8” (20.32) 101/2” (26.67) 02217011
.87”-1.00” (2.21-2.54) 1,790 (7,962) 8” (20.32) 111/2” (29.21) 02217012
.94”-1.06” (2.39-2.69) 1,790 (7,962) 9” (22.86) 121/2” (31.75) 02217013
1.00”-1.18” (2.54-3.00) 1,790 (7,962) 9” (22.86) 131/2” (34.29) 02217014
1.06”-1.25” (2.69-3.17) 1,790 (7,962) 9” (22.86) 141/2” (36.83) 02217015
E-Eye length M-Mesh length at nominal diameter
5/16 ''
(.80) Dia.
1/4''
(.64)
4 7/8''
(12.38)
2''
(5.08)
Screw Hook
No. 203-03-001
Yield Strength 900 lbs (4003)
Wire Management Products Support Grips
Support Grips
Service Drop
Universal Eye, Tin-Coated Bronze
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through
T-48.
M
E
Dim. to
Sliding Bar
Fully Ext'd.
Heavy Duty, Universal Eye,
Closed Mesh, Multi-Weave
M
E
Dim. to
Sliding Bar
Fully Ext'd.
L
ight Duty, Universal Eye,
C
losed Mesh Single Weave
Light Duty, Universal Eye, Closed Mesh, Single Weave*
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.23”-.31” (.58-.79) 290 (1,290) 9” (22.86) 33/4” (9.52) 02216016
.29”-.37” (.74-.94) 290 (1,290) 10” (25.40) 41/4” (10.79) 02216017
.35”-.44” (.89-1.12) 500 (2,224) 10” (25.40) 43/4” (12.06) 02216018
.41”-.50” (1.04-1.27) 500 (2,224) 11” (27.94) 5” (12.70) 02216019
.46”-.56” (1.17-1.42) 660 (2,936) 12” (30.48) 51/4” (13.33) 02216020
.52”-.62” (1.32-1.57) 790 (3,514) 13” (33.02) 61/4” (15.87) 02216021
.58”-.68” (1.47-1.73) 790 (3,514) 13” (33.02) 61/2” (16.51) 02216022
.64”-.75” (1.63-1.90) 790 (3,514) 13” (33.02) 63/4” (17.14) 02216023
.70”-.81” (1.78-2.06) 790 (3,514) 13” (33.02) 71/4” (18.41) 02216024
.75”-.87” (1.90-2.21) 1,020 (4,537) 14” (35.56) 8” (20.32) 02216025
.81”-.94” (2.06-2.39) 1,020 (4,537) 14” (35.56) 81/4” (20.95) 02216026
.87”-1.00” (2.21-2.54) 1,020 (4,537) 14” (35.56) 8 3/4” (22.22) 02216027
.94”-1.06” (2.39-2.69) 1,020 (4,537) 15” (38.10) 9” (22.86) 02216028
1.00”-1.18” (2.54-3.00) 1,020 (4,537) 15” (38.10) 91/2” (24.13) 02216029
1.06”-1.25” (2.69-3.17) 1,020 (4,537) 15” (38.10) 91/2” (24.13) 02216030
Heavy Duty, Universal Eye, Closed Mesh, Multi-Weave*
For permanent support when cable end is available to be installed.
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.23”-.31” (.58-.79) 500 (2,224) 11” (27.94) 41/2” (11.43) 02217016
.28”-.37” (.74-.94) 500 (2,224) 11” (27.94) 51/2” (13.97) 02217017
.35”-.44” (.89-1.12) 870 (3,870) 12” (30.48) 61/2” (16.51) 02217018
.41”-.50” (1.04-1.27) 870 (3,870) 12” (30.48) 71/2” (19.05) 02217019
.46”-.56” (1.17-1.42) 1,050 (4,670) 12” (30.48) 8” (20.32) 02217020
.52”-.62” (1.32-1.57) 1,050 (4,670) 13” (33.02) 81/2” (21.59) 02217021
.58”-.68” (1.47-1.73) 1,050 (4,670) 13” (33.02) 91/2” (24.13) 02217022
.64”-.75” (1.63-1.90) 1,390 (6,183) 13” (33.02) 91/2” (24.13) 02217023
.70”-.81” (1.78-2.06) 1,390 (6,183) 14” (35.56) 101/2” (26.67) 02217024
.75”-.87” (1.90-2.21) 1,390 (6,183) 14” (35.56) 101/2” (26.67) 02217025
.81”-.94” (2.06-2.39) 1,390 (6,183) 14” (35.56) 101/2” (26.67) 02217026
.87”-1.00” (2.21-2.54) 1,790 (7,962) 14” (35.56) 111/2” (29.10) 02217027
.94”-1.06” (2.39-2.69) 1,790 (7,962) 15” (38.10) 121/2” (31.75) 02217028
1.00”-1.18” (2.54-3.00) 1,790 (7,962) 15” (38.10) 131/2” (34.29) 02217029
1.06”-1.25” (2.69-3.17) 1,790 (7,962) 15” (38.10) 141/2” (36.83) 02217030
E-Eye length M-Mesh length at nominal diameter.
* Change catalog number from 022 to 024 for stainless steel. Consult factory for
availability.
T-37
Dimensions in Inches (mm) www.hubbell-wiring.com
Bus Drop Grips Wire Management Products
Support Grips
Bus Drop
Single Eye, Universal Eye, Galvanized Steel
T-38 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43 through
T-48.
Strain
Relief
Grip
Bus
Drop
Grips
Motor Box
Safety Spring
Strain
Relief
Grip
M
E
Dim. to
Sliding Bar
Fully Ext'd.
M
E
Dim. to
Sliding Bar
Fully Ext'd.
Safety Spring
Maximum Approx. Breaking
Deflection Strength Length* Diameter
Inches/Lbs Lbs. Inches Inches Model Catalog
(cm/N) (N) (cm) (cm) Lbs. (n) Numbers
2
3/4
” at 40 lbs.
500 81/4”3/4” 40 lb. spring 20302001
(6.98 cm. at 178 N)
(2,224) (20.95) (1.90) (178)
31/8” at 80 lbs. 850 81/4” 1” 80 lb. spring 20302002
(7.94 cm. at 356 N) (3,781) (20.95) (2.54) (356)
Springs can be used with single eye grips by disassembling drawbar from coil,
placing through eye and replacing drawbar.
*No load.
Single Eye Wide Range
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.24”-.32” (.61-.81) 350 (1,557) 3” (7.62) 31/2” (8.89) 073041276
.32”-.43” (.81-1.09) 450 (2,002) 4” (10.16) 4” (10.16) 073041277
.43”-.56” (1.09-1.42) 550 (2,446) 6” (15.24) 43/4” (12.06) 073041278
.56”-.73” (1.42-1.85) 1,000 (4,448) 7” (17.78) 6” (15.24) 073041279
.73”-.85” (1.85-2.16) 1,400 (6,227) 7” (17.78) 63/4” (17.14) 073041280
.85”-1.00” (2.16-2.54) 1,400 (6,227) 8” (20.32) 8” (20.32) 073041281
1.00”-1.25” (2.54-3.17) 1,500 (6,672) 9” (22.86) 91/2” (24.13) 073041282
Universal Eye Wide Range
Cable Diameter Approx. Breaking E M Catalog
Range Inches (cm) Strength Lbs. (N) Inches (cm) Inches (cm) Numbers
.32”-.43” (.81-1.09) 450 (2,002) 10” (25.40) 4” (10.16) 073041284
.43”-.56” (1.09-1.42) 550 (2,446) 12” (30.48) 43/4” (12.06) 073041285
.56”-.73” (1.42-1.85) 1,000 (4,448) 13” (33.02) 6” (15.24) 073041286
.73”-.85” (1.85-2.16) 1,400 (6,227) 13” (33.02) 63/4” (17.14) 073041287
.85”-1.00” (2.16-2.54) 1,400 (6,227) 14” (35.56) 8” (20.32) 073041288
1.00”-1.25” (2.54-3.17) 1,500 (6,672) 15” (38.10) 91/2” (24.13) 073041289
E-Eye length M-Mesh length at nominal diameter
Bus Drop Grips and Safety Springs
Kellems Bus Drop Grips are offered with either a single eye or universal
bale attachment. The mesh is single weave galvanized steel with the
patented wide range construction. They are suitable for indoor use only.
Application
Bus Drop Grips provide a safe, easy and economical method to support
flexible cord or bus drop cable at bus duct and other industrial areas.
Benefits
• Easily installed.
• Absorb tension, vibration and pull with no cable damage.
• Patented mesh construction.
Safety Spring
Springs can be used with single eye grips by disassembling drawbar from
coil, placing through eye and replacing drawbar.
Wire Management Products Conduit Riser Grips
T-39
Dimensions in Inches (mm) www.hubbell-wiring.com
Support Grips
Conduit Riser
Ring Type, Single Weave, Tin-Coated Bronze
Read This Data
It is important that you read all breaking strength, safety and technical data
relating to this product on pages T-43 through T-48.
Single Weave, Closed Mesh
Kellems®Conduit Riser Support Grips are available in closed mesh and in
split mesh with lace or rod closures, to cover all applications including
single cable or cable bundle support. Refer to technical section, T-43 for
grip selection assistance for cable bundles. The standard material is tin-
coated bronze strand. The grip is permanently fastened to a support ring,
resulting in a one piece unit which will allow air ventilation within the
conduit. This ring supported grip is ideal for supporting electrical cable at
standard rigid conduit. The rings will fit schedule 40, standard rigid
conduit. The rings will fit schedule 40, standard rigid conduit. See page
T-42 for ring dimensions. For permanent support when cable end is
available to be installed through the grip.
Suitable For Schedule 40 Conduit Only
Cable Sizes .50”- .62” .63”-.74” .75”- .99” 1.00”- 1.24” 1.25”- 1.49” 1.50”-1.74” 1.75”-1.99” 2.00”- 2.49” 2.50” -2.99” 3.00”- 3.49” 3.50”- 3.99”
Inches (cm) (1.27-1.57) (1.60-1-88) (1.90-2.51) (2.54-3.15) (3.17-3.78) (3.81-4.42) (4.44-5.05) (5.08-6.32) (6.35-7.59) (7.62-8.86) (8.89-10.13)
Model R050 R062 R075 R100 R125 R150 R175 R200 R250 R300 R350
Length
Inches (cm) 8” (20.32) 9” (22.86) 11” (27.94) 12” (30.48) 12” (30.48) 14” (35.56) 15” (38.10) 17” (43.18) 18” (45.72) 20” (50.80) 21” (53.34)
Conduit Sizes Catalog Numbers
Inches Approx. Breaking Strength Lbs. (N)
3/4
”02211106 •••••••• ••
530 (2,357)
1” 02211100 02211101••••••• ••
490 (2,179) 790 (3,514)
1
1/4
”02211001 02211002 02211003 •••••• ••
450 (2,002) 740 (3,292) 1,030 (4,581)
1
1/2
”• 02211006 02211007 02211009 •••• • • •
690 (3,069) 970 (4,315) 1,610 (7,161)
2” 0221110 02211107 02211010 02211012 02211013 •••• ••
370 (1,645) 640 (2,847) 920 (4,092) 1,520 (6,761) 1,610 (7,161)
2
1/2
”• • • • 02211017 02211018 02211019 •• ••
1,510 (6,716) 1,610 (7,161) 2,150 (9,563)
3” • • • 02211022 02211023 02211024 02211025 02211026 •••
1,340 (5,960) 1,400 (6,227) 1,490 (6,627) 1,990 (8,851) 3,260 (14,500)
3
1/2
”• • • • • • • 02211033 02211034 ••
2,970 (13,211) 3,260 (14,500)
4” • • • • • • 02211040 02211041 02211042 02211043 •
1,670 (7,248) 2,680 (11,921) 2,890 (12,855) 4,080 (18,148)
4
1/2
”• • • • • • • • 02211051 02211052 •
2,520 (11,208) 3,470 (15,434)
5” • • • • • • • • 02211061 02211062 02211063
2,150 (9,563) 2,860 (12,721) 3,130 (13,922)
6” • • • • • • • • • 02211072 02211073
2,245 (9,986) 2,245 (9,986)
Note: Refer to page T-43 for multiple cables in a single conduit riser grip.
Conduit Riser Grips Wire Management Products
Support Grips
Conduit Riser
Ring Type, Double Weave, Tin-Coated Bronze
T-40 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all breaking strength, safety and
technical data relating to this product on pages T-41
through T-46.
Double Weave, Split Mesh, Lace Closing
Kellems®Conduit Riser Support Grips will support cable runs
in vertical or sloping standard rigid conduit. The grip is
fastened to a support ring which seats on the rim of the
conduit. The entire grip is supported by the conduit itself
and no other hardware is required. See page T-40 for ring
dimensions. The rings will fit schedule 40, standard rigid
conduit. For permanent support when cable end
is not available.
Suitable For Schedule 40 Conduit Only
Cable Sizes .75”- .99” 1.00”- 1.24” 1.25”- 1.49” 1.50”-1.74” 1.75”- 1.99” 2.00”- 2.49” 2.50”- 2.99” 3.00”- 3.49” 3.50” -3.99”
Inches (cm) (1.90-2.51) (2.54-3.15) (3.17-3.78) (3.81-4.42) (4.44-5.05) (5.08-6.32) (6.35-7.59) (7.62-8.86) (8.89-10.13)
Model RS075 RS100 RS125 RS150 RS175 RS200 RS250 RS300 RS350
Length 11” (27.94) 12” (30.48) 12” (30.48) 14” (35.56) 15” (38.10) 17” (43.18) 18” (45.72) 20” (50.80) 21” (53.34)
Inches (cm)
Conduit Sizes Catalog Numbers
Inches Approx. Breaking Strength Lbs. (N)
1
1/4
”02212003 ••••• • ••
1,580 (7,028)
1
1/2
”02212007 02212009 •••• • ••
1,500 (6,672) 2,040 (9,024)
2” 02212010 02212012 02212013 •• • • • •
1,430 (6,361) 1,930 (8,585) 2,040 (9,074)
2
1/2
”• • 02212017 02212018 02212019 ••••
1,910 (8,496) 2,040 (9,074) 2,730 (12,143)
3” • • 02212023 02212024 02212025 02212026 •••
1,780 (7,917) 1,890 (8,407) 2,520 (11,209) 4,300 (19,126)
3
1/2
”•••••02212033 02212034 ••
3,910 (17,392) 4,300 (19,126)
4”••••02212040 02212041 02212042 02212043 •
2,110 (9,385) 3,530 (15,701) 3,820 (16,991) 5,380 (23,930)
5”•••••• 02212061 02212062 02212063
2,860 (12,721) 3,760 (16,724) 4,170 (18,548)
6”•••••• 02212071 02212072 02212073
2,365 (10,519) 2,955 (13,144) 2,955 (13,144)
Note: Refer to page T-43 for multiple cables in a single conduit riser grip.
Wire Management Products Conduit Riser Grips
Support Grips
Conduit Riser
Ring Type, Single Weave, Tin-Coated Bronze
T-41
Dimensions in Inches (mm) www.hubbell-wiring.com
Read This Data
It is important that you read all breaking strength, safety
and technical data relating to this product on pages T-43
through T-48.
Single Weave, Split Mesh, Rod Closing Benefits
• Easy and fast to install.
• Will not damage electrical cable.
• Allows cable to expand or contract.
• Ideal way to hold cable in vertical conduit.
• Prevents cable creep in conduit.
• Helps prevent cable pullouts.
• The rings will fit schedule 40, standard rigid conduit.
• For support when cable end is not available.
Suitable For Schedule 40 Conduit Only
Cable Sizes .75”- .99” 1.00”- 1.24” 1.25”- 1.49” 1.50”- 1.74” 1.75”-1.99” 2.00”- 2.49” 2.50”- 2.99” 3.00”-3.49” 3.50”-3.99”
Inches (cm) (1.90-2.51) (2.54-3.15) (3.17-3.78) (3.81-4.42) (4.44-5.05) (5.08-6.32) (6.35-7.59) (7.62-8.86) (8.89-10.13)
Model RR075 RR100 RR125 RR150 RR175 RR200 RR250 RR300 RR350
Length
Inches (cm) 11” (27.94) 12” (30.48) 13” (33.02) 14” (35.56) 15” (38.10) 16” (40.64) 18” (45.72) 19” (48.26) 21” (53.34)
Conduit Sizes Catalog Numbers
Inches Approx. Breaking Strength Lbs. (N)
1
1/4
”02213003 ••••• • ••
1,020 (4,537)
1
1/2
”02213007 02213009 •••• • ••
970 (4,315) 1,610 (7,161)
2” 02213012 02213013 •• • • • •
• 1,520 (6,761) 1,610 (7,161)
2
1/2
”• • 02213017 02213018 •• • ••
1,510 (6,716) 1,610 (7,161)
3” • • 02213023 02213024 02213025 02213026 •••
1,400 (6,227) 1,490 (6,627) 1,990 (8,851) 3,260 (14,500)
3
1/2
”•••••02213033 02213034 ••
2,970 (13,211) 3,260 (14,500)
4”•••••02213041 02213042 ••
2,680 (13,255) 2,890 (17,855)
Note: Refer to page T-43 for multiple cables in a single conduit riser grip.
Conduit Riser Ring Dimensions Wire Management Products
Support Grips
Conduit Riser
T-42 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-43
through T-48
O.D.
I.D.
T
T
S
Conduit Ring Dimensions
Ring dimensions are found in the chart below. The ring material is
corrosion resistant. These rings will fit schedule 40, standard rigid
conduit sizes only.
Conduit Size O.D. I.D. S T
Inches Ring Number Inches (cm) Inches (cm) Inches (cm) Inches (cm)
3/4”C-
3/4.94” (2.39) .62” (1.57) • .19” (.48)
1” C-1 1.17” (2.97) .80” (2.03) • .19” (.48)
11/4” C-11/41.50” (3.81) 1.03” (2.62) 1.31” (3.33) .16” (.41)
11/2” C-11/21.76” (4.47) 1.23” (3.12) 1.52” (3.86) .16” (.41)
2” C-2 2.23” (5.66) 1.55” (3.94) 1.97” (5.00) .16” (.41)
21/2” C-21/22.67” (6.78) 2.05” (5.21) 2.40” (6.10) .16” (.41)
3” C-3 3.20” (8.13) 2.55” (6.48) 2.97” (7.54) .22” (.56)
31/2” C-31/23.80” (9.65) 3.05” (7.75) 3.47” (8.81) .22” (.56)
4” C-4 4.30” (10.92) 3.55” (9.02) 3.94” (10.01) .22” (.56)
41/2” C-41/24.80” (12.19) 4.03” (10.24) 4.45” (11.30) .22” (.56)
5” C-5 5.30” (13.46) 4.46” (11.33) 4.96” (12.60) .22” (.56)
6” C-6 6.30” (16.00) 5.36” (13.61) 5.96” (15.14) .25” (.63)
Wire Management Products Technical Data
T-43
Dimensions in Inches (mm) www.hubbell-wiring.com
Kellems®Grips For Cable Support
Technical Section
For Conduit Riser Grips Only†
For Cables of Equal Diameters
Under “Number of Cables in One Grip,” find diameter of your single cable in vertical
column. Read the grip diameter range to the right.
If your diameter is the maximum of the range shown, go to the next larger size for Split
Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .85” (2.16cm) diameter, for a Closed Grip select the
1.50”-1.74” (3.81cm-4.42cm) range, for a Split Grip select the 1.75”-1.99”
(4.44cm-5.05cm) range.
Number of Equal Diameter Cables in One Grip
Grip Dia. Range
2 3 4 5 6 and 7 8 9 Inches (cm)
.29-.36 .24-.30 .21-.25 .18-.22 .16-.20 .15-.18 .14-.17 .50-.62
(.74-.91) (.61-.76) (.53-.63) (.46-.56) (.41-.51) (.38-.46) (.36-.43) (1.27-1.57)
.37-.43 .31-.36 .26-.30 .23-.27 .21-.24 .19-.22 .18-.20 .63-.74
(.94-1.09) (.79-.91) (.66-.76) (.58-.69) (.53-.61) (.48-.56) (.46-.51) (1.60-1.88)
.44-.58 .37-.48 .31-.41 .28-.36 .25-.32 .23-.29 .21-.27 .75-.99
(1.12-1.47) (.94-1.22) (.79-1.04) (.71-.91) (.63-.81) (.58-.74) (.53-.69) (1.90-2.51)
.59-.72 .49-.60 .42-.51 .37-.45 .33-.40 .30-.36 .28-.34 1.00-1.34
(1.50-1.83) (1.24-1.52) (1.07-1.30) (.94-1.14) (.84-1.02) (.76-.91) (.71-.86) (2.54-3.15)
.73-.87 .61-.72 .52-.61 .46-.54 .41-.48 .37-.43 .35-.40 1.25-1.49
(1.85-2.21) (1.55-1.83) (1.32-1.55) (1.17-1.37) (1.04-1.22) (.94-1.09) (.89-1.02) (3.17-3.78)
.88-1.01 .73-.85 .62-.71 .55-.63 .49-.56 .44-.51 .41-.47 1.50-1.74
(2.24-2.57) (1.85-2.16) (1.57-1.80) (1.40-1.60) (1.24-1.42) (1.12-1.30) (1.04-1.19) (3.81-4.42)
1.02-1.16 .86-.96 .72-.81 .64-.72 .57-.64 .52-.58 .48-.54 1.75-1.99
(2.59-2.95) (2.18-2.44) (1.83-2.06) (1.63-1.83) (1.45-1.63) (1.32-1.49) (1.22-1.37) (4.44-5.05)
1.17-1.44 .97-1.20 .82-1.02 .73-.90 .65-.80 .59-.72 .55-.67 2.00-2.49
(2.97-3.66) (2.46-3.05) (2.08-2.59) (1.85-2.29) (1.65-2.03) (1.50-1.83) (1.40-1.70) (5.08-6.32)
1.45-1.73 1.21-1.45 1.03-1.22 .91-1.08 .81-.96 .73-.87 .68-.81 2.50-2.99
(3.68-4.39) (3.07-3.68) (2.62-3.10) (2.31-2.74) (2.06-2.44) (1.85-2.21) (1.73-2.06) (6.35-7.59)
1.74-2.02 1.46-1.69 1.23-1.43 1.09-1.26 .97-1.11 .83-1.01 .82-.94 3.00-3.49
(4.42-5.13) (3.71-4.29) (3.12-3.63) (2.77-3.20) (2.46-2.82) (2.11-2.57) (2.08-2.39) (7.62-8.86)
2.03-2.31 1.70-1.93 1.44-1.63 1.27-1.44 1.12-1.27 1.02-1.15 .95-1.08 3.50-3.99
(5.16-5.87) (4.32-4.90) (3.66-4.14) (3.23-3.66) (2.84-3.23) (2.59-2.92) (2.41-2.74) (8.89-10.13)
†This chart is to be used for determining grip size when multiple cables are held in a single conduit riser grip.
Select The Correct Support Grip
For Cables of Unequal Diameters
Step 1 Take circumference of cable bundle.
Step 2 Take circumference bundle divide by 3.1416 which equals approximate cable bundle diameter.
Step 3 Choose appropriate grip for application and desired breaking strength and use approximate diameter matched to the
cable diameter in the catalog.
NOTE: It is always recommended that, when multiple cables are installed in a support grip, the tail end of the grip be banded or
tightly taped after installation on the cable bundle.
Technical Data Wire Management Products
Kellems®Grips For Cable Support
Technical Section
Bus Drop Grips
T-44 Dimensions in Inches (mm)
www.hubbell-wiring.com
Bus Drop Grips and Safety Springs
Kellems Bus Drop Grips are offered with either a single eye or universal
bale attachment. The mesh is single weave galvanized steel with the
patented wide range construction. They are suitable for indoor use only.
Application
Bus Drop Grips provide a safe, easy and economical method to support
flexible cord or bus drop cable at bus duct and other industrial areas.
Benefits
• Easily installed.
• Absorb tension, vibration and pull with no cable damage.
• Patented mesh construction.
Safety Spring
Springs can be used with single eye grips by disassembling drawbar from
coil, placing through eye and replacing drawbar.
Strain
Relief
Grip
Bus
Drop
Grips
Motor Box
Safety Spring
Strain
Relief
Grip
Wire Management Products Technical Data
T-45
Dimensions in Inches (mm) www.hubbell-wiring.com
Kellems®Grips For Cable Support
Technical Section
Kellems Support Grips
Kellems Support Grips are used to hold the weight of
electrical cable as it hangs in a vertical, sloping or
horizontal position. Electrical cable must be
supported, or its dead weight can cause excessive
strain or pullout at the connections resulting in power
failure. Support grips also absorb additional strain
from flexure, vibration, expansion and contraction.
Kellems Support Grips listed in this catalog are
made of high grade, non-magnetic tin-coated bronze
strand. Stainless steel grips, made of alloy 302–304
SST for severe service or unusual environmental
conditions, are available on request.
Select the Correct Support Grip
Each Kellems grip is designed to work on a specific range of
cable diameters.
Step 1 Refer to the Kellems chart below to determine the grip
style best suited for your application.
Step 2 Determine your cable outside diameter.
Step 3 Find the grip size that encompasses your cable
diameter.
Step 4 Whenever possible, use a closed mesh that assembles
over the cable end. If the cable end is not available, use
a split mesh.
Step 5 Where available, select an eye style that suits your
needs.
Step 6 Select the proper material—tinned bronze or stainless
steel*.
Step 7 Estimate the tension to be put on the grip, establish the
working load you require and compare this to the listed
approximate breaking strength of the grip to insure that
the grip will be strong enough. Refer to page L-84 for
safety and working load considerations.
Support Grip Selection Chart
Grip Styles Application Page
Closed mesh Standard, permanent support, cable end available. T-30 to T-33
Split lace closing Standard, permanent support, cable end unavailable. T-30 to T-33
Split rod closing Standard, temporary support, cable end unavailable. Tape or band tail T-30 to T-33
end of wire mesh grip after positioning for permanent support.
Material* Tin-coated bronze standard or stainless steel by special request. T-30 to T-42
Standard support grips Support vertical runs to 99 ft. loads to 600 lbs. T-30 to T-33
Heavy duty grips Support vertical runs over 100 ft loads over 600 lbs. T-34, T-35
Service drop Light duty to support service entrance cable. T-36, T-37
Bus drop Light duty support, indoors only, on Bus drop cable. T-38
Conduit riser Support cable runs in rigid (Schedule 40) conduit. T-39 to T-42
Fiber optic cable support grips Support fiber optic cable. T-53
*Most catalog listed support grips are made of tin-coated bronze strand. To order stainless steel support grips, change the first three
catalog number digits from 022-XX-XXX to 024-XX-XXX. Consult factory for details.
Eye Styles
S
ingle
D
ouble
U
niversal
O
ffset
Technical Data Wire Management Products
T-46 Dimensions in Inches (mm)
www.hubbell-wiring.com
Kellems®Grips For Cable Support
Technical Section
The broad application of Kellems grips on a wide variety
of objects requires that adequate safety factors be used
to establish working loads. The approximate breaking
strength of a Kellems grip represents an average
calculation based on data established from actual direct
tension testing done in our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are
never the same. The tension, diameter, movement,
number of objects gripped, gripping surface, and the
attachments used are just some of the factors which
vary with each application. These factors, together with
the effects of abrasion, corrosion, prior use or abuse
and any other variables of a specific application, must
be considered by the user and the grip replaced as
appropriate. Where the conditions of the application are
not well defined or known, or where risk of injury to
persons or property is involved, a greater safety factor
should be utilized.
Under normal conditions, Kellems’ recommended
factor of safety is five for catalog listed pulling grips,
and ten for catalog listed support grips. The factory
should be consulted for specific application
recommendations where strength and holding power
are important factors.
Any warranty as to quality, performance or fitness for use
of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored,
handled, used, maintained, and inspected by the user at
a frequency appropriate for the use and condition of the
grip.
Examples
Approx. Breaking Safety Max. Rec. Catalog
Grip Style Strength Lbs. (N) Factor Load Lbs. (N) Numbers
Pulling Grips 27,200 (120,986) 5 5,440 (24,197) 03301027
Support 1,610 (7,161) 10 161 (716) 02202020
The maximum recommended working load then is the tension to be exerted on the grip
in application with a margin of safety to take care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable to him.
The metric unit of measure (force) for breaking strength and load is newtons (N). To convert from newtons to the metric unit of
weight (kilograms) the conversion factor is 9.808 newtons/kilogram.
Support Grip Materials
Material Feature Grip Type
Tin-coated bronze wire Corrosion resistant for normal outside areas Support grips
Non-magnetic Service drop grips
Moderate strength Conduit riser grips
Stainless steel wire (302-304) High strength Support grips
Corrosion resistant Service drop grips
Galvanized steel wire Slightly magnetic Bus drop grips
Not subject to continuous outside environment Bus drop grips
Approvals
CSA Certifications are indicated on appropriate product catalog pages.
Note: It is always recommended that the tail end of the grip be banded after the installation on the cable to prevent accidental
release of the mesh.
Safety And Working Load Factors For Wire Mesh Grips
Wire Management Products Technical Data
Kellems®Grips For Cable Support
Technical Section
T-47
Dimensions in Inches (mm) www.hubbell-wiring.com
Split Support Grip Lace Closing Instructions
Single Weave Grips should be laced with single strand lacing; double weave with
double strand. Lacing strands should be the same material as the grip. Kellems
supplies the appropriate lacing with each grip.
1. Start the lacing at the lead or anchoring end of the grip. Thread the lacings
through the first two loops of the split and pull through until the lacings are
centered at this point. Lace as you would your shoe, crossing the lacings before
lacing the next two loops.
2. Don’t pull lacing too tight. Leave a space between adjoining loops approximately
equal to the width of one diamond of the mesh.
3. Twist the lacing strands tightly together at the tail end of the grip.
4. Wrap the ends of the lacings once or twice tightly around the tail of the grip,
twisting the ends together securely. Excess lace can be cut off.
Split Support Grip Rod Closing Instructions
The stainless steel rod is a precise built-in feature which makes threading easy and
fast. The strands of the mesh pass around the rod and match up with the strands
from the opposite direction. The rod does not touch the cable at any point and
therefore cannot cut the cable. Rod Closing Grips are reusable. They may be
removed and reused as many times as desired.
1. Fast to install
Wrap the grip around the cable and thread the rod through the performed loops
with a corkscrew motion, using the curved end of the rod to engage the loops.
2. The action required is a steady push and twist simultaneously. The fingers of the
left hand are used to bring the loops together just ahead of the hook on
the end of the rod.
3. To remove, simply pull the rod out.
Technical Data Wire Management Products
T-48 Dimensions in Inches (mm)
www.hubbell-wiring.com
Kellems®Grips For Cable Support
Technical Section
Multiple Cable Selection Charts for Cables of Equal Diameters
For Standard Support Grips*
For Cables of Equal Diameters
Under “Number of Cables in One Grip,” find diameter of your single cable in vertical
column. Read the grip diameter range to the right.
Caution: When a grip is used on multiple cables, the tail end of the grip should be
banded or tightly taped after positioning on the cables.
If your diameter is the maximum of the range shown, go to the next larger size for
Split Grips, stay with the same size for Closed Grips.
Example: 3 cables, each with .85” (2.16cm) diameter, for a Closed Grip select the
1.50”-1.74” (3.81cm-4.42cm) range, for a Split Grip select the 1.75”-1.99”
(4.44cm-5.05cm) range.
Number of Cables in One Grip
Grip Dia. Range
2 3 4 5 6 and 7 8 9 Inches (cm)
.30-.38 .25-.31 .22-.27 .19-.24 .17-.22 .15-.19 .14-.18 .50-.61
(.76-.97) (.63-.79) (.56-.69) (.48-.61) (.43-.56) (.38-.48) (.36-.46) (1.27-1.55)
.38-.44 .31-.36 .27-.31 .24-.29 .22-.26 .19-.23 .18-.21 .62-.74
(.97-1.12) (.79-.91) (.69-.79) (.61-.74) (.56-.66) (.48-.56) (.46-.53) (1.57-.188)
.44-.59 .36-.49 .31-.42 .29-.38 .26-.34 .23-.31 .21-.28 .75-.99
(1.12-1.50) (.91-1.24) (.79-1.07) (.74-.97) (.66-.86) (.58-.79) (.53-.71) (1.90-2.51)
.59-.75 .49-.63 .42-.54 .38-.48 .34-.43 .31-.39 .28-.35 1.00-1.24
(1.50-1.90) (1.24-1.60) (1.07-1.37) (.97-1.22) (.86-1.09) (.79-.99) (.71-.89) (2.54-3.15)
.75-.90 .63-.76 .54-.65 .48-.58 .43-.52 .39-.46 .36-.42 1.25-1.49
(1.90-2.29) (1.60-1.93) (1.37-1.65) (1.22-1.47) (1.09-1.32) (.99-1.17) (.89-1.07) (3.17-3.78)
.90-1.07 .76-.89 .65-.77 .58-.67 .52-.60 .46-.54 .42-.49 1.50-1.74
(2.29-2.72) (1.93-2.26) (1.65-1.96) (1.47-1.70) (1.32-1.52) (1.17-1.37) (1.07-1.24) (3.81-4.42)
1.07-1.22 .89-1.02 .77-.88 .67-.77 .60-.69 .54-.62 .49-.56 1.75-1.99
(2.72-3.10) (2.26-2.59) (1.96-2.24) (1.70-1.96) (1.52-1.75) (1.37-1.57) (1.24-1.42) (4.44-5.05)
1.22-1.53 1.02-1.28 .88-1.10 .77-.96 .69-.86 .62-.77 .56-.71 2.00-2.49
(3.10-3.89) (2.59-3.25) (2.24-2.79) (1.96-2.44) (1.75-5.54) (1.57-1.96) (1.42-1.80) (5.08-6.32)
1.53-1.83 1.28-1.53 1.10-1.32 .96-1.16 .86-1.03 .77-.93 .71-.85 2.50-2.99
(3.89-4.65) (3.25-3.89) (2.79-3.35) (2.44-2.95) (2.18-2.62) (1.96-2.36) (1.80-2.16) (6.35-7.59)
1.83-2.14 1.53-1.79 1.32-1.54 1.16-1.35 1.03-1.20 .93-1.08 .85-.99 3.00-3.49
(4.65-5.44) (3.89-4.55) (3.35-3.91) (2.95-3.43) (2.62-3.05) (2.36-2.74) (2.16-2.51) (7.62-8.86)
2.14-2.44 1.79-2.05 1.54-1.76 1.35-1.54 1.20-1.37 1.08-1.24 .99-1.13 3.50-3.99
(5.44-6.20) (4.55-5.21) (3.91-4.47) (3.43-3.91) (3.05-3.48) (2.74-3.15) (2.51-2.87) (8.89-10.13)
2.44-2.75 2.05-2.30 1.76-1.98 1.54-1.74 1.37-1.55 1.24-1.39 1.13-1.27 4.00-4.49
(6.20-6.98) (5.21-5.84) (4.47-5.03) (3.91-4.42) (3.48-3.94) (3.15-3.53) (2.87-3.23) (10.16-11.40)
2.75-3.06 2.30-2.56 1.98-2.20 1.74-1.93 1.55-1.72 1.39-1.55 1.27-1.41 4.50-4.99
(6.98-7.77) (5.84-6.50) (5.03-5.59) (4.42-4.90) (3.94-4.37) (3.53-3.94) (3.23-3.58) (11.43-12.67)
*This chart is not to be used for Conduit Riser Grips. Refer to the chart for Conduit Riser multiple cable section.
Select The Correct Support Grip
For Cables of Unequal Diameter
Step 1 Take circumference of cable bundle.
Step 2 Take circumference bundle divide by 3.1416 which equals approximate cable bundle diameter.
Step 3 Choose appropriate grip for application and desired breaking strength and use approximate diameter matched to the
cable diameter in the catalog.
NOTE: It is always recommended that, when multiple cables are installed in a support grip, the tail end of the grip be banded or
tightly taped after installation on the cable bundle.
Wire Management Products Fiber Optic Grips
Kellems®Products for
Fiber Optic Cable
Pulling Tools, Support Devices
T-49
Dimensions in Inches (mm) www.hubbell-wiring.com
O
PTISOKTM grip is a new and revolutionary tool to pull preterminated
f
iber optic cables. They will protect the connectors and guide
t
he bundle through the pulling environment.
P
ulling Grips are used for outside plant cable.
T
hey are easy to install and remove, reusable,
a
nd have a slim profile for small build up.
G
rips for cable support are easy to install or position. They come
i
n a closed style when the cable end is available, and a split rod
s
tyle for mid-span installation. Will support the cable’s weight as it
h
angs in vertical, sloping or horizontal position.
Fiber Optic Grips Wire Management Products
T-50 Dimensions in Inches (mm)
www.hubbell-wiring.com
Pulling Grips
Fiber Optic Cable Grips
Special Purpose
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-54
through T-57.
OPTISOK™ Non-metallic Fiber Optic Pulling Tool For Preterminated,
Inside Plant Fiber Optic Cables and Bundles of Twisted Pair
OPTISOK™ Non-Metallic Fiber Optic Pulling Tool
Bundle/Size Approx. O/A Ring Ring Maximum
Range Length O.D. Thickness Work Load Catalog
Inches (cm) Inches (cm) Inches (cm) Inches (cm) lbs. (N) Numbers
.125”-.562” (.318-1.427) 28” (71.12) .71” (18.03) .10” (2.54) 30 (133) CCPS1
.250”-.750” (.635-1.905) 31” (78.74) .71” (18.03) .10” (2.54) 40 (178) CCPS2
.750”-1.750” (19.05-44.50) 33” (83.82) 1.57” (39.88) .16” (4.06) 50 (222) CCPS3
Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel
Pulling Grip For Loose Tube Fiber Optic Cable, Galvanized Steel
Diameter Mesh Eye Eye Lug Maximum
Range Length Length Diameter Diameter Breaking Strength Catalog
Inches (cm) Inches (cm) Inches (cm) Inches (cm) Inches (cm) lbs. (N) Number
.312”-.625” (.79-1.59) 22.5” (57.15) 6.3” (16.00) .20” (.51) .51” (1.30) 3,000 (13,344) PFOLT312
Patented
Patented
Wire Management Products Fiber Optic Grips
Pulling Grips
Fiber Optic Cable Grips
Double/Single Weave Mesh, Galvanized Steel, for Outside Plant Cable
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-54
through T-57.
F-O Pulling Grip, Flexible Eye
F-O Pulling Grip, Flexible Eye
Approx.
Cable Breaking
Diameter Range Strength E M D Catalog
Inches (cm) Lbs. (N) Approx Inches (cm) Numbers
.10”-.22” (.25-.56) 1,000 (4,448) 5.5” (14) 9” (23) 0.8” (2) 033291000
.21”-.35” (.53-.89) 1,500 (6,672) 5.5” (14) 14” (36) 0.8” (2) 033291001
.32”-.48” (.81-1.22) 2,200 (9,786) 6.0” (15) 18” (46) 0.9” (2.30) 033291002
.42”-.61” (1.07-1.55) 2,800 (12,454) 6.0” (15) 21” (53) 0.9” (2.30) 033291003
.53”-.74” (1.35-1.88) 3,300 (14,678) 6.5” (17) 24” (61) 1.3” (3.30) 033291004
.64”-.87” (1.63-2.21) 4,700 (20,906) 6.5” (17) 27” (69) 1.3” (3.30) 033291005
E-Eye length M-Mesh length at nominal diameter
F-O Pulling Grip, Swivel Eye
F-O Pulling Grip, Swivel Eye
Approx.
Cable Breaking E M D
Diameter Range Strength Approx. Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Inches (cm) Numbers
.10”-.22” (.25-.56) 1,000 (4,448) 4.0” (10.16) 9” (22.86) 0.9” (2.29) 033291007
.21”-.35” (.53-.89) 1,500 (6,672) 4.0” (10.16) 14” (35.56) 0.9” (2.29) 033291008
.32”-.48” (.81-1.22) 2,200 (9,786) 4.0” (10.16) 18” (45.72) 0.9” (2.29) 033291009
.42”-.61” (1.07-1.55) 2,800 (12,454) 4.0” (10.16) 21” (53.34) 0.9” (2.29) 033291010
.53”-.74” (1.35-1.88) 3,300 (14,678) 4.5” (11.43) 24” (60.96) 1.3” (1.3) 033291011
.64”-.87” (1.63-2.21) 4,700 (20,906) 4.5” (11.43) 27” (68.58) 1.3” (1.3) 033291012
E-Eye length M-Mesh length at nominal diameter
M
D
E
Patente
d
M
D
E
Patented
T-51
Dimensions in Inches (mm) www.hubbell-wiring.com
Fiber Optic Grips Wire Management Products
Pulling Grips
Fiber Optic Cable Grips
Galvanized Steel for Outside Plant Cable
T-52 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-54
through T-57.
F-O Pulling Grip, Flexible Eye, Low Profile,
Double/Single Weave Mesh
F-O Pulling Grip, Flexible Eye, Low Profile,
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Numbers
.10”-.22 (.25-.56) 900 (4,003) 7.5” (19) 10” (25) 033291193
.21”-.35” (.53-.89) 1,400 (6,227) 7.5” (19) 14” (36) 033291194
.32”-.48” (.81-1.22) 2,000 (8,896) 8.5” (22) 19” (48) 033291195
.42”-.61” (1.07-1.55) 2,500 (11,120) 8.5” (22) 21” (53) 033291196
.53”-.74” (1.35-1.88) 3,000 (13,344) 8.5” (22) 23” (58) 033291197
.64”-.87” (1.63-2.21) 4,200 (18,862) 8.5” (22) 25” (64) 033291198
.75”-1.00” (1.90-2.54) 4,200 (18,862) 8.5” (22) 28” (71) 033291199
E-Eye length M-Mesh length at nominal diameter
F-O Pulling Grip, Single Weave Mesh
F-O Slack Pulling Grip, Split Mesh Rod Closing, Single Weave
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Numbers
.25”-.37” (.63-.94) 300 (1,334) 3” (7.6) 4.7” (12) 033291015
.38”-.49” (.97-1.24) 800 (3,558) 3” (7.6) 5” (13) 033291016
.50”-.61” (1.27-1.55) 800 (3,558) 3” (7.6) 7.5” (19) 033291017
.62”-.74” (1.57-1.88) 1,200 (5,338) 3” (7.6) 8” (20) 033291018
E-Eye length M-Mesh length at nominal diameter
EM
EM
Wire Management Products Fiber Optic Grips
Support Grips
Fiber Optic Cable Grips
Single Weave, Tin-Coated Bronze
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-54
through T-57.
For permanent support when
cable end is available to be
installed through grip.
For support when cable end not
available.
M
E
Single Eye, Split Mesh,
Rod Closing, Single Weave
M
E
Single Eye, Closed Mesh,
Single Weave
Single Eye, Closed Mesh Single Weave
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Numbers
.18”-.25” (.46-.63) 300 (1,334) 3” (7.6) 1.7” (4.30) 022291000
.23”-.32” (.58-.81) 300 (1,334) 3” (7.6) 2.5” (6.40) 022291001
.30”-.39” (.76-.99) 300 (1,334) 4” (10) 2.5” (6.40) 022291002
.37”-.48” (.94-1.22) 300 (1,334) 5” (13) 4” (10) 022291003
.46”-.58” (1.17-1.47) 400 (1,779) 6” (15) 4” (10) 022291004
.56”-.71” (1.42-1.80) 600 (2,669) 7” (18) 5.5” (14) 022291005
.69”-.88” (1.75-2.24) 800 (3,558) 8” (20) 6” (15) 022291006
E-Eye length M-Mesh length at nominal diameter
Single Eye, Split Mesh, Rod Closing Single Weave
Approx.
Cable Breaking E M
Diameter Range Strength Approx. Approx. Catalog
Inches (cm) Lbs. (N) Inches (cm) Inches (cm) Numbers
.18”-.25” (.46-.63) 300 (1,334) 3” (7.60) 2.5” (6.40) 022291016
.23”-.32” (.58-.81) 300 (1,334) 3” (7.60) 2.5” (6.40) 022291017
.30”-.39” (.76-.99) 300 (1,334) 4” (10) 2.5” (6.40) 022291018
.37”-.48” (.94-1.22) 300 (1,334) 5” (13) 4” (10) 022291019
.46”-.58” (1.17-1.47) 400 (1,779) 6” (15) 5” (13) 022291020
.56”-.71” (1.42-1.80) 600 (2,669) 7” (18) 5” (13) 022291021
.69”-.88” (1.75-2.24) 800 (3,558) 8” (20) 6” (15) 022291022
E-Eye length M-Mesh length at nominal diameter
T-53
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Kellems®Fiber Optic Cable Products
Technical Section
T-54 Dimensions in Inches (mm)
www.hubbell-wiring.com
Kellems has wide experience with grips for the new
technology of fiber optic cable. As the industry leader in
producing wire mesh grips for the stringent requirements
of fiber optic applications, Kellems has developed several
completely new series of grips for use with fiber optic
communications cable.
These new grips include pulling grips with built in swivels,
grips with steel ends to protect fragile cable ends, grips
with low profiles to pull cables in tight places and the
OPTISOK™an effective tool to place preterminated
cables. Also available are grips to support fiber optic
cable.
Select the Correct Fiber Optic Grip
Each Kellems grip is designed to work on a specific range of
cable diameters.
Step 1 Determine your cable outside diameter.
Step 2
Find the grip size that encompasses your cable diameter.
Step 3 Whenever possible, use a closed mesh that
assembles over the cable end. If the cable end
is not available, use a split mesh.
Step 4
Where available, select an eye style that suits your needs.
Step 5
Estimate the tension to be put on the grip, establish the
working load you require and compare this to the listed
approximate breaking strength of the grip to insure that
the grip will be strong enough.
Safety And Working Load Factors For Wire Mesh Grips
The broad application of Kellems grips on a wide variety
of objects requires that adequate safety factors be used to
establish working loads. The approximate breaking
strength of a Kellems grip represents an average
calculation based on data established from actual direct
tension testing done in our engineering laboratories.
It is impossible to catalog or guarantee a safety factor
suitable for all applications as operating conditions are
never the same. The tension, diameter, movement,
number of objects gripped, gripping surface, and the
attachments used are just some of the factors which vary
with each application. These factors, together with the
effects of abrasion, corrosion, prior use or abuse and any
other variables of a specific application, must be
considered by the user and the grip replaced as
appropriate. Where the conditions of the application are
not well defined or known or where risk of injury to persons
or property is involved, a greater safety factor should be
utilized.
Under normal conditions, Kellems’ recommended
factor of safety is five for catalog listed pulling grips,
and ten for catalog listed support grips. The factory
should be consulted for specific application
recommendations where strength and holding power
are important factors.
Any warranty as to quality, performance or fitness for use
of grips is always premised on the condition that the
published breaking strengths apply only to new, unused
grips, and that such products are properly stored,
handled, used, maintained and inspected by the user at a
frequency appropriate for the use and condition of the
grip.
For grip applications on materials other than those that
the grips have been specifically designed for, consult the
factory.
Examples
Grip Approx. Breaking Safety Max. Rec. Catalog
Style Strength Lbs. (N) Factor Load Lbs. (N) Numbers
Pulling 2,500 (11,120) 5 500 (2,224) 033291196
Support 400 (1,779) 10 40 (178) 022291004
The maximum recommended working load then is the tension to be exerted on the grip in application with a margin of safety to take
care of unforeseen and unusual circumstances.
It is the end-user’s decision to determine how much of a safety factor is acceptable to him.
Fiber Optic Grip Materials
Material Features Product Group
Galvanized steel wire High strength Pulling Grip
Not subject to continuous outside environment
Tin-coated bronze wire Corrosion resistant for normal outside areas Support grips
Non-magnetic
Moderate strength
Non-metallic braid Superior flex life OPTISOK
Non-conductive
Corrosion resistant
Moderate strength
Approvals
CSA Certification is indicated on appropriate product catalog pages.
Wire Management Products Technical Data
Kellems®Fiber Optic Cable Products
Technical Section
Product Data
OPTISOK™
T-55
Dimensions in Inches (mm) www.hubbell-wiring.com
Kellems offers a unique and simple to use tool for
the installation of preconnectorized fiber optic
cables, jumpers and bundles of twisted pair
communication cables - the OPTISOK.
The OPTISOK is a highly flexible and expandable
nonmetallic sleeve open on one end and with a
pulling ring on the other. It will expand to enclose
the larger group of fiber optic connectors and grab
the cable below the connector bundle by wrapping
and taping to provide a gripping tool that will grab
the cable(s) below the connectors. The pulling ring
can be attached to a pulling line or fish tape and
the OPTISOK will act as the pulling tool.
OPTISOK will contain and protect the connector
bundle and save time and labor by making the
pulling job easier, protecting the connectors from
possible damage during the pull and facilitating the
passage of the connector bundle through cramped
and tight spaces. The OPTISOK can be used to
pull cables through plenums, underfloor duct, office
partitions, raised access floors and conduits. Three
sizes are available for all applications.
How to Select OPTISOK
• Identify connector bundle diameter to be
inserted into the OPTISOK.
• Choose appropriate catalog number based
on size range.
Installation Information
Step 1. Expand open end of OPTISOK and gently
work in fiber optic connector bundle.
Step 2. Still gently, work connector bundle up to the
forward section of the Optisok.
Step 3. Starting at approximately 6” from tail end of
OPTISOK, tightly fold over the Optisok
around cables and tape wrapped section
3” past tail end onto the bundle.
Step 4. Securely attach pulling line or tape to
pulling ring.
Note: To remove OPTISOK carefully unwrap tape and slide
out cables and connectors or cut OPTISOK away
without damaging connectors or cables.
1
2
3
4
Technical Data Wire Management Products
Kellems®Fiber Optic Cable Products
Technical Section
Product Data
T-56 Dimensions in Inches (mm)
www.hubbell-wiring.com
Pulling Grip for Loose Tube Fiber Optic Cable
Kellems offers a wire mesh specifically designed to pull loose tube
fiber optic cable and meet the special pulling requirements
recommended by fiber optic cable manufacturers.
Many fiber optic cable manufacturers require special cable preparation
prior to pulling where a short section of the outer jacket is stripped off
exposing the aramid strength member. This creates two cable
diameters, one including the jacket and a second smaller diameter at
the strength member. Kellems new grip with its special weave will
accommodate and securely grab both diameters, at the outside jacket
and the internal aramid strength member.
Additionally, this galvanized steel mesh grip has longer leads at the
pulling eye to facilitate pulling the cable up through the top, a very low
profile lug and eye to slip through tight areas, and short shoulders to
protect the cable while maintaining the slim profile.
The grip can be used to pull cable overhead as well as underground
through conduit and duct. It easily mates with a swivel and has the
necessary strength to securely make pulls.
Application Information
• Prior to pulling cable, follow cable manufacturers’ cable preparation
recommendations.
• Never exceed cable manufacturers’ pulling tension
recommendations.
• Never use grips to approximate breaking strength-factor of safety
of 5 recommended.
Pulling Grips for Other Outside Plant Cables,
Swivel Eye, Flexible Eye, Split Style, Low Profile
Kellems Pulling Grips for fiber optic cable are made of high strength
galvanized steel strand. They feature a multiweave mesh, with one-half
the mesh length double weave, and the second half single weave. This
special weave provides positive holding power while allowing the grip
to remain flexible with no damage to the cable jacket. Added features
include a steel nose cone which protects the cable end and allows the
grip to pass easily through conduit and enclosures. The eye connects
easily to a swivel or a pulling line. Several grip sizes are available to
accommodate all diameters of fiber optic cable.
Application
Kellems Flexible Eye Pulling Grips for fiber optic cable are used for the
installation of fiber optic communication lines either underground,
overhead, through conduit or through enclosures. They will fit single
cables or cable bundles, are easily installed on the cable, and are
reusable.
Benefits
• High strength multiweave mesh for positive holding power.
• Highly flexible mesh to follow the pulling path of the cable.
• Steel nose cone reduces snags and hang-ups and protects cable end.
• Easily installed and removed.
• A dependable, reusable pulling tool.
Wire Management Products Technical Data
Kellems®Fiber Optic Cable Products
Technical Section
Product Data
T-57
Dimensions in Inches (mm) www.hubbell-wiring.com
Support Grips for Fiber Optic Cable
Kellems Support Grips for fiber optic cable are specially designed to hold the
cable weight as it hangs in a vertical or horizontal position. Fiber optic cable
must be supported and Kellems Grips provide the support easily and
economically.
These grips are made of high grade, non-magnetic tin-coated bronze strand.
They are offered in universal bale or single eye configurations and are
available in either closed mesh (for use where the cable end is available) or in
split mesh, rod closing (for installation on existing cable runs or at specific
locations).
Split Support Grip Rod Closing Instructions
The stainless steel rod is a precise built-in feature which makes threading
easy and fast. The strands of the mesh pass around the rod and match up
with the strands from the opposite direction. The rod does not touch the
cable at any point and therefore cannot cut the cable. Rod Closing Grips are
reusable. They may be removed and reused as many times as desired.
Fast to Install
Step 1. Wrap the grip around the cable and thread the rod through the
preformed loops with a corkscrew motion, using the curved end of the
rod to engage the loops.
Step 2. The action required is a steady push and twist simultaneously. The
fingers of the left hand are used to bring the loops together just ahead
of the hook on the end of the rod.
Step 3. To remove, simply pull the rod out.
Note Page (Blank Page) Wire Management Products
NOTES
T-58 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Deluxe Cord GrIps
Kellems®Grips for Strain Relief
Liquidtight, Dusttight
For Insulated Cables and Flexible, Liquidtight Conduits
T-59
Dimensions in Inches (mm) www.hubbell-wiring.com
An NPT and PG threaded body allows easy attachment to either threaded
hub or knock-out in box.
Endless weave provides easy cable/flexible conduit installation.
Stainless steel mesh is corrosion resistant. Can be used inside or
outside. It eliminates cable or flexible conduit pull out and reduces
costly downtime.
Multiweave grip gives cable arc-of-bend control minimizing cable
damage and extending cable life. It is the strongest strain relief
device available. Meets and exceeds all code requirements.
Prevents cable/conduit pull-out.
A liquidtight fitting is available with both cable and conduit fittings.
Prevents liquids from running through the fitting into the enclosure.
Deluxe Cord GrIps Wire Management Products
Strain Relief
Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
T-60 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68
through T-74.
*Cable jacket may have to be stripped to
pass through connector body.
Kellems®Deluxe Cord Grips are
suitable for use in hazardous locations
per Class I Div. 2, Class II Div. 1 & 2,
Class III Div. 1 & 2 of the National
Electric Code Sections 501-4(b), 502-
4(a), 502-4(b), 503-3(a) and 503 3(b).
Aluminum
Compression
Nut
Aluminum
Collar
Tapered Threads
Neoprene
Bushing
Stainless
Steel
Mesh
Aluminum Body
S
traight Male
Straight Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.250”-.312” (.63-.79) 07401001
.312”-.375” (.79-.95) 3/8”F107401002
.375”-.437” (.95-1.11) 07401003
.187”-.250” (.47-.63) 07401004
.250”-.375” (.63-.95) 1/2”F207401006
.375”-.500” (.95-1.27) 07401008
.500”-.625” (1.27-1.59) 07401010
.625”-.750” (1.59-1.90) 1/2”F3074011247*
.750”-.875” (1.90-2.22) 074011248*
.187”-.250” (.47-.63) 07401011
.250”-.375” (.63-.95) 3/4”F207401013
.375”-.500” (.95-1.27) 07401015
.500”-.625” (1.27-1.59) 07401017
.625”-.750” (1.59-1.90) 3/4”F307401018
.750”-.875” (1.90-2.22) 074011249*
.375”-.500” (.95-1.27) 074011195
.500”-.625” (1.27-1.59) 07401019
.625”-.750” (1.59-1.90) 1” F4 07401021
.750”-.875” (1.90-2.22) 07401023
.875”-1.000” (2.22-2.54) 07401025
1.000”-1.125” (2.54-2.86) 074011250*
1.125”-1.250” (2.86-3.17) 1” F5 074011028*
1.250”-1.375” (3.17-3.49) 074011029*
.750”-.875” (1.90-2.22) 074011251
.875”-1.000” (2.22-2.54) 07401026
1.000”-1.125” (2.54-2.86) 11/4”F507401027
1.125”-1.250” (2.86-3.17) 07401028
1.250”-1.375” (3.17-3.49) 074011178*
.750”-.875” (1.90-2.22) 074011252
.875”-1.000” (2.22-2.54) 07401029
1.000”-1.125” (2.54-2.86) 11/2”F507401030
1.125”-1.250” (2.86-3.17) 07401031
1.250”-1.375” (3.17-3.49) 07401032
1.312”-1.437” (3.33-3.65) 074011253
1.437”-1.562” (3.65-3.97) 074011254*
1.562”-1.687” (3.97-4.28) 11/2”F6074011255*
1.687”- 1.812” (4.28-4.60) 074011256*
1.750”-1.875” (4.44-4.76) 074011257*
1.250”-1.375” (3.17-3.49) 074011258
1.312”-1.437” (3.33-3.65) 074011259
1.437”-1.562” (3.65-3.97) 2” F6 07401033
1.562”-1.687” (3.97-4.28) 07401034
1.687”-1.812” (4.28-4.60) 07401035
1.750”- 1.875” (4.44-4.76) 074011260
1.812”-1.937” (4.60-4.92) 074011261
1.937”-2.062” (4.92-5.24) 074011262*
2.062”-2.187” (5.24-5.55) 2” F7 074011263*
2.187”-2.312” (5.55-5.87) 074011264*
2.312”-2.437” (5.87-6.19) 074011265*
1.688”-1.812” (4.29-4.60) 074011030
1.812”-1.937” (4.60-4.92) 074011031
1.937”-2.062” (4.92-5.24) 21/2”F7074011032
2.062”-2.187” (5.24-5.55) 074011033
2.187”-2.312” (5.55-5.87) 074011034
2.312”-2.437” (5.87-6.19) 074011266*
1.937”-2.062” (4.92-5.24) 074011036
2.062”-2.187” (5.24-5.55) 3” F7 074011037
2.187”-2.312” (5.55-5.87) 074011038
2.312”-2.437” (5.87-6.19) 074011039
2.437”-2.625” (6.19-6.67) 074011186
2.625”-2.812” (6.67-7.14) 3” F8 074011187
2.812”-3.000” (7.14-7.62) 074011188
3.000”-3.250” (7.62-8.25) 074011189*
90° Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.250”-.312” (.63-.79) 07401071
.312”-.375” (.79-.95) 3/8”F107401072
.375”-.437” (.95-1.11) 07401073
.187”-.250” (.47-.63) 07401074
.250”-.375” (.63-.95) 07401076
.375”-.500” (.95-1.27) 1/2”F207401078
.500”-.625” (1.27-1.59) 07401080*
.375”-.500” (.95-1.27) 07401081
.500”-.625” (1.27-1.59) 3/4”F307401083
.625”-.750” (1.59-1.90) 07401084*
.750”-.875” (1.90-2.22) 074011275*
.500”-.625” (1.27-1.59) 07401085
.625”-.750” (1.59-1.90) 1” F4 07401087
.750”-.875” (1.90-2.22) 07401089
.875”-1.000” (2.22-2.54) 07401091*
1.000”-1.125” (2.54-2.86) 074011229*
.750”-.875” (1.90-2.22) 074011230
.875”-1.000” (2.22-2.54) 07401137
1.000”-1.125” (2.54-2.86) 1 1/4”F507401108
1.125”-1.250” (2.86-3.17) 074011042*
1.000”-1.125” (2.54-2.86) 074011045
1.125”-1.250” (2.86-3.17) 11/2”F5074011046
1.250”-1.375” (3.17-3.49) 074011047
1.312”-1.437” (3.33-3.65) 074011233
1.437”-1.562” (3.65-3.97) 2” F6 074011244
1.687”-1.812” (4.28-4.60) 074011246
1.750”-1.875” (4.44-4.76) 074011234*
Female Thread
.375”-.500” (.95-1.27) 1/2”F207401043
.500”-.625” (1.27-1.59) 07401045
.500”-.625” (1.27-1.59) 3/4”F207401052
.625”-.750” (1.59-1.90) 3/4”F407401053
45° Male Thread
.250”-.375” (.63-.95) 074011236
.375”-.500” (.95-1.27) 1/2”F2074011021
.500”-.625” (1.27-1.59) 074011237*
.500”-.625” (1.27-1.59) 074011049
.625”-.750” (1.59-1.90) 3/4”F3074011051*
.750”-.875” (1.90-2.22) 074011239*
.625”-.750” (1.59-1.90) 074011055
.750”-.875” (1.90-2.22) 1” F4 074011057
.875”-1.000” (2.22-2.54) 074011199*
1.000”-1.125” (2.54-2.86) 1 1/4”F5074011059
1.125”-1.250” (2.86-3.17) 074011060
Wire Management Products Deluxe Cord Grips
Strain Relief
Deluxe Cord Grips
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68
through T-74.
*Cable jacket may have to be stripped to
pass through connector body.
4
5°
F
emale
9
0°
T-61
Dimensions in Inches (mm) www.hubbell-wiring.com
Deluxe Cord Grips Wire Management Products
Strain Relief
Deluxe Cord Grips
Nylon Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
T-62 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68 through
T-74.
9
0°
S
traight Male
Straight Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.187”-.250” (.47-.63) 074011331
.250”-.375” (.63-.95) 1/2”F2074011332
.375”-.500” (.95-1.27) 074011333
.500”-.625” (1.27-1.59) 074011334*
.375”-.500” (.95-1.27) 074011335
.500”-.625” (1.27-1.59) 3/4”F3074011336
.625”-.750” (1.59-1.90) 074011337
.750”-.875” (1.90-2.22) 074011338*
.625”-.750” (1.59-1.90) 074011341
.750”-.875” (1.90-2.22) 1” F4 074011342
.875”-1.000” (2.22-2.54) 074011343
1.000”-1.125” (2.54-2.86) 074011344*
90° Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.250”-.375” (.63-.95) 074011346
.375”-.500” (.95-1.27) 1/2”F2074011347
.500”-.625” (1.27-1.59) 074011348*
.375”-.500” (.95-1.27) 074011349
.500”-.625” (1.27-1.59) 3/4”F3074011350
.625”-.750” (1.59-1.90) 074011351*
*Cable jacket may have to be stripped to pass through connector body.
Nylon
Compression
Nut
Stainless
Steel
Collar
Tapered Threads
Neoprene
Bushing
Stainless
Steel
Mesh
Nylon Body
Nylon Fittings Non-metallic Mesh, Liquidtight for
Insulated Cables
Straight Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.187”-.250” (.47-.63) CG304NM
.250”-.312” (.63-.79) 3/8”F1CG305NM
.312”-.375” (.79-.95) CG306NM
.187”-.250” (.47-.63) CG404NM
.250”-.375” (.63-.95) 1/2”F2CG406NM
.375”-.500” (.95-1.27) CG408NM
.375”-.500” (.95-1.27) CG608NM
.500”-.625” (1.27-1.59) 3/4”F3CG610NM
.625”-.750” (1.59-1.90) CG612NM
.500”-.625” (1.27-1.59) CG810NM
.625”-.750” (1.59-1.90) 1” F4 CG812NM
.750”-.875” (1.90-2.22) CG814NM
.875”-1.000” (2.22-2.54) CG816NM
90° Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.250”-.375” (.63-.95) 1/2”F2CG40690NM
.375”-.500” (.95-1.27) CG40890NM
.375”-.500” (.95-1.27) CG60890NM
.500”-.625” (1.27-1.59) 3/4”F3CG61090NM
.625”-.750” (1.59-1.90) CG61290NM*
.625”-.750” (1.59-1.90) 1” F4 CG81290NM
.750”-.875” (1.90-2.22) CG81490NM
Note: Non-metallic locknuts are available upon request. Refer to page L-99.
*Cable jacket may have to be stripped to pass through connector body.
Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight, for
Insulated Cables
Straight Male Thread
Grip Diameter Range Thread Size Form Catalog
Inches (cm) N.P.T. (Inches) Size Numbers
.187”-.250” (.47-.63) CG404SST
.250”-.375” (.63-.95) 1/2”F2CG406SST
.375”-.500” (.95-1.27) CG408SST
.500”-.625” (1.27-1.59) CG410SST
.375”-.500” (.95-1.27) CG608SST
.500”-.625” (1.27-1.59) 3/4”F3CG610SST
.625”-.750” (1.59-1.90) CG612SST
.750”-.875” (1.90-2.22) CG614SST
.500”-.625” (1.27-1.59) CG810SST
.625”-.750” (1.59-1.90) 1” F4 CG812SST
.750”-.875” (1.90-2.22) CG814SST
.875”-1.000” (2.22-2.54) CG816SST
Wire Management Products Deluxe Cord Grips
Strain Relief
Deluxe Cord Grips
Nylon Fittings, Non-metallic Mesh, Liquidtight, for Insulated Cables and
Stainless Steel Fittings, Stainless Steel Mesh, Liquidtight, for
Insulated Cables
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68 through
T-74.
S
traight Male
90
°
S
traight Male
T-63
Dimensions in Inches (mm) www.hubbell-wiring.com
Deluxe Cord Grips Wire Management Products
Strain Relief
PG Threaded Deluxe Cord Grip
Aluminum Fittings, Stainless Steel Mesh, Liquidtight, for Insulated Cables
T-64 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68 through
T-74.
Straight Male
Straight Male Thread
Cord Diameter Range Hub Catalog
Inches (cm) Size Numbers
.500”-.625” (1.27-1.59) PG16 074PG16010
.500”-.625” (1.27-1.59) PG21 074PG21010
.625”-.750” (1.59-1.90) PG21 074PG211247
.750”-.875” (1.90-2.22) PG21 074PG211248
.625”-.750” (1.59-1.90) PG29 074PG29021
.750”-.875” (1.90-2.22) PG29 074PG29023
.875”-1.000” (2.22-2.54) PG29 074PG29025
1.125”-1.250” (2.86-3.17) PG29 074PG291028*
1.125”-1.250” (2.86-3.17) PG36 074PG36028*
*Cable jacket may have to be stripped to pass through connector body.
Specifications
Material
Body Aluminum
Mesh Stainless Steel
Bushing Neoprene
Operating Temperature –30° F to +225° F
(–34° C to +107° C).
Hazardous Locations Suitable for use in hazardous
locations per Class 1, Div. 2,
Class II, Div. 1 & 2, Class III,
Div. 1 & 2.
Flammability
Mesh grip Rated UL 94HB.
Fitting Rated UL 94V-2.
Agency
Approvals Control numbers
Underwriters UL898D, UL899D.
Laboratories Inc.
Wet Locations
The products are suitable for
use in wet locations when a listed
sealing ring is used between box and fitting.
Wire Management Products Adapters
Strain Relief
Adapters for Multi-Pin, Circular, Connectors
Aluminum
T-65
Dimensions in Inches (mm) www.hubbell-wiring.com
Adapters for Multi-Pin Connectors
Kellems Adapters are devices formating
AN-MS connectors and other multi-pin
connectors to Kellems grips with NPT threaded
fittings. They are made of aluminum with
internal threads and replace the connector
cord clamp. These adapters permit the
installation of Kellems Grips, to prevent cable
or conduit pull-out and control arc-of-bend.
Applications
Adapters allow the installation of Kellems®Grips on
multi-pin connectors at electrical consoles, mobile
equipment, control switches, assembly equipment
and testing machines.
Benefits
• Easy installation.
• Allows the use of Kellems grips.
• Extends connector and cable life.
Liquidtight Adapters
Liquidtight
Conduit Grips
(Insulated
Adapters Deluxe Cord Grips Strain Relief Grips Throat)
AN-MS AN-MS N.P.T.
Connector Cable Clamp Thread Thread Catalog Cable Diameter Catalog Cable Diameter Catalog Catalog
Size** Number*** Size A in. Size B in. Numbers Range Inches (cm) Numbers Range Inches (cm) Numbers Numbers
8S, 10S 3057-3 1/2”x 28 091041000 .250”-.312”(.63-.79) 07401001
10SL, 12, 12S 3057-4 5/8”x 24 3/8”091041001 .312”-.375”(.79-.95) 07401002
14, 14S 3057-6 3/4”x 20 091041002 .375”-.437”(.95-1.11) 07401003
14, 14S 3057-6 3/4”x 20 091041003 .187”-.250”(.47-.63 07401004 .24”-.32”(.61-.81) 073031200 –
16, 16S 3057-8 7/8”x 20 1/2”091041004 .250”-.375”(.63-.95) 07401006 .32”-.43”(.81-1.09) 073031201 074093512
18 3057-10 1”x 20 091041006 .375”-.500”(.95-1.27) 07401008 .43”-.54”(1.09-1.37) 073031202 –
.500”-.625”(1.27-1.59) 07401010*
16, 16S 3057-8 7/8”x 20 091041005 .187”-.250”(.47-.63) 07401011
18 3057-10 1”x 20 3/4”091041007 .250”-.375”(.63-.95) 07401013
20, 22 3057-12 13/16”x 18 091041008 .375”-.500”(.95-1.27) 07401015 .54”-.74”(1.37-1.85) 073031203 074093513
.500”-.625”(1.27-1.59) 07401017
.625”-.750”(1.59-1.90) 07401018
20, 22 3057-12 13/16”x 18 091041009 .375”-.500”(.95-1.27) 074011195
24, 28 3057-16 17/16”x 18 091041010 .500”-.625”(1.27-1.59) 07401019
32 3057-20 13/4”x 18 1”091041012 .625”-.750”(1.59-1.90) 07401021 .73”-.97”(1.85-2.46) 073031204 074093514
36 3057-24 2”x 18 091041015 .750”-.875”(1.90-2.22) 07401023
.875”-1.000”(2.22-2.54) 07401025
24, 28 3057-16 17/16”x 18 091041011 .750”-.875”(1.90-2.22) 074011251
32 3057-20 13/4”x 18 11/4”091041013 .875”-1.000”(2.22-2.54) 07401026
36 3057-24 2”x 18 091041016 1.000”-1.125”(2.54-2.86) 07401027 .97”-1.25”(2.46-3.17) 073031205 074093515
1.125”-1.375”(2.86-3.17) 07401028
32 3057-20 13/4”x 18 091041014 .875”-1.000”(2.22-2.54) 07401029
36 3057-24 2”x 18 11/2”091041017 1.000”-1.125”(2.54-2.86) 07401030 –074093516
40 3057-28 21/4”x 16 091041019 1.125”-1.250”(2.86-3.17) 07401031
1.250”-1.375”(3.17-3.49) 07401032
* Cable jacket may have to be stripped to pass through connector body.
** No. stamped on connector shell.
*** No. stamped on clamp shell.
Adapter
T
hread "A"
Connector
N.P.T. Thread Size "B" Cable Or Conduit
Grip
I-Grips Wire Management Products
Strain Relief
I-Grips
Plastic-Coated, Galvanized Steel Mesh for Insulated Cables
T-66 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68
through T-74.
Application
Kellems®I-Grips will fit 2 wire, 3 wire, 4 wire and 5 wire Hubbell
Insulgrip®plugs and connector bodies. The eye tabs fit under the
nylon cord clamp and the screws slide through the eyelets, securing
the grip in place.
These grips are for indoor use only.
Benefits
• Easily attached to Insulgrip plugs and connector bodies.
• Controls cable arc-of-bend.
• Provides heavy-duty strain relief.
• Fits all sizes.
Note: I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof
covers are to be installed.
I-Grips
Cable Diameter E M Catalog
Range Inches (cm) Inches (cm) Inches (cm) Numbers
.32”-.43” (.81-1.09) 1.25” (3.17) 4” (10.16) 07310001
.43”-.56” (1.09-1.42) 1.25” (3.17) 4.75” (12.06) 07310002
.56”-.73” (1.42-1.85) 1.50” (3.81) 6” (15.24) 07310003
.73”-.85” (1.85-2.16) 1.50” (3.81) 6.5” (16.51) 07310004
.85”-1.00” (2.16-2.54) 1.50” (3.81) 8” (20.32) 07310005
1.00”-1.25” (2.54-3.17) 1.50” (3.81) 10” (25.40) 07310006
E-Eye length M-Mesh length at nominal diameter Eyelet hole diameter .203 (.52)
ME
Wire Management Products Strain Relief Grips
Strain Relief
Dustight Strain Relief Grips
Aluminum Fittings, Galvanized Steel Mesh, for Insulated Cables
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-68
through T-74.
Insulated
A
N
on-Insulated
Non-Insulated Wide Range Strain Relief
Mesh
Cable Diameter Thread Size Length @ Nom. Catalog
Range Inches (cm.) N.P.T. (Inches) Dia. Inches (cm) Numbers
.24”-.32” (.61-.81) 1/2”3
1/4” (8.25) 073031200
.32”-.43” (.81-1.09) 1/2”3
3/4” (9.52) 073031201
.43”-.54” (1.09-1.37) 1/2”4
3/4” (12.06) 073031202
.54”-.73” (1.37-1.85) 3/4”6
1/2” (16.51) 073031203
.73”-.97” (1.85-2.46) 1” 7” (17.78) 073031204
.97”-1.25” (2.46-3.17) 11/4” 9” (22.86) 073031205
.73”-.97” (1.85-2.46) PG29 7” (17.78) 073PG291204
Insulated Wide Range Strain Relief with Insulating Bushing
Mesh Min. Space
Thread Length @ Between
Cable Diameter Size Nom. Dia. Dim. Grips Catalog
Range In. (cm.) Inches Inches(cm) A In.(cm) B In.(cm) Numbers
.24”-.32” (.61-.81) 1/2” N.P.S. 31/4” (8.25) 1” (2.54) 11/4” (3.17) 073031206
.32”-.43” (.81-1.09) 1/2” N.P.S. 33/4” (9.52) 1” (2.54) 11/4” (3.17) 073031207
.43”-.54” (1.09-1.37) 1/2” N.P.S. 43/4” (12.06) 1” (2.54) 11/4” (3.17) 073031208
.54”-.73” (1.37-1.85) 3/4” N.P.S. 61/2” (16.51) 1” (2.54) 11/2” (3.81) 073031209
.73”-.97” (1.85-2.46) 1” N.P.S. 7” (17.78) 13/16” (3.02) 13/4” (4.44) 073031210
.97”-1.25” (2.46-3.17) 11/4” N.P.S. 9” (22.86) 13/16” (3.02) 21/4” (5.71) 073031211
1.25”-1.50” (3.17-3.81) 11/2” N.P.T. 113/4” (29.84) 13/16” (3.02) 21/2” (6.35) 073031212
1.50”-1.70” (3.81-4.32) 2” N.P.T. 131/4” (33.65) 13/8” (3.49) 31/4” (8.25) 073031213
1.70”-2.00” (4.32-5.08) 21/2” N.P.T. 131/2” (34.29) 11/2” (3.81) 35/8” (9.21) 073031214
2.00”-2.45” (5.08-6.22) 21/2” N.P.T. 133/4” (34.92) 11/2” (3.81) 35/8” (9.21) 073031215
T-67
Dimensions in Inches (mm) www.hubbell-wiring.com
Strain Relief System Selection Chart
Cord or Conduit Type Fitting or Page
Grip Type Application Features Range Inches (cm) Attachment Number
Deluxe Cord Outdoors or indoors where Aluminum fittings, .187”-3.250” PG, N.P.T. aluminum, T-60, T-61,
Aluminum subjected to moisture or stainless steel mesh, (.47-8.25) male straight, T-64
Fitting/ splash. Examples are crane neoprene oil-and- 45° male, 90° male,
Stainless and hoist pendant drop watertight bushing. female straight.
SteelGrip stations, hand tools, pumps Double-single weave. Thread sizes 3/8”-3”.
and processing equipment.
Deluxe Cord Outdoors or indoors where Nylon fitting, stainless .187”-1.125” N.P.T. nylon, T-62
Nylon Fitting/ subjected to moisture or steel mesh, double-single (.47-2.86) male straight,
Stainless splash. Examples are weave, neoprene oil-and- 90° male. Thread
SteelGrip marine and food watertight bushing. sizes 1/2”-1”.
processing equipment.
Deluxe Cord Indoor or outdoors. Non-metallic grip is .187”-1.000” N.P.T. nylon, T-63
Nylon Fitting/ Provides liquidtight seal, corrosion resistant, (.47-2.54) straight male, thread sizes 3/8”-1”
Non-metallic where exposed to moisture. nonconductive and 90° male, thread sizes 1/2”-1”.
Grip Excellent for oil refining provides superior grip-
and chemical processing. ping and flexing benefits.
Neoprene liquidtight
bushing. Nylon fitting.
Deluxe Cord Indoor or outdoor use where Stainless steel fitting .187”-1.000” Straight male T-63
Stainless exposed to moisture. Very and grip for strength. (.47-2.54) Only with N.P.T.
SteelFitting strong for heavy abuse areas Neoprene liquidtight Thread sizes 1/2”-1”.
And Grip such as drilling platforms, bushing. Double/single
steel mills and mines. weave grip.
Wide Range Indoor use only for wiring Neoprene gasket–seals .240”-2.450” Straight male N.P.S. T-67
Strain Relief of electrical enclosures, out cips, dirt, dust. (.61-6.22) or N.P.T.
machine tools, portable One piece design with
power tools, bus drop galvanized steel mesh.
cable systems. Insulating bushing available.
Zinc-plated steel locknut.
Non-metallic Wiring or machine tools, Stainless steel mesh, .375”-2.008” N.P.T. steel, T-100
Flexible electrical enclosures, liquidtight fittings with trade size male Hubbell fittings,
Conduit Grip motors and systems “O” ring and locknut. straight male, 90°
(UL Type A) where conduit is subject Thread sizes 1/2”-2”.
to vibration and strain.
Liquidtight, Wiring of machine tools, Stainless steel mesh, .375”-4.000” N.P.T. 1/2”-4”, T-101
Flexible, electrical enclosures, motors liquidtight fittings. trade sizes Hubbell fittings,
Metal and systems where metallic Sealing “O” rings Male straight,
Conduit Grip liquidtight flexible conduit (optional). Choice of 45° male, 90° male,
is subjected to vibration, fittings. female straight.
flexure, motion or strain.
Technical Data Wire Management Products
Kellems®Grips for Strain Relief
Technical Section
T-68 Dimensions in Inches (mm)
www.hubbell-wiring.com
Kellems Strain Relief Grips are designed to prevent
tension from being transmitted to joints and
terminals on electrical cord, cable and conduit. In
most applications, a Kellems grip for strain relief is
stronger than the cable itself and gives much
greater security than the use of a fitting alone.
Kellems Grips for strain relief help make electrical
systems safer, and save money by minimizing
downtime from costly electrical failure due to cable
pull-out. Kellems Grips also aid in compliance with
the National Electric Code’s terminal tension
protection requirements (see NEC Section 400-10.).
Select the Correct Grip for Strain Relief
Kellems Grips for strain relief are designed to fit on
electrical cord, cable or flexible conduit.
Step 1 Refer to the chart below to determine the grip style
best suited for your application.
Step 2 Determine your cable outside diameter or conduit size.
Step 3 Locate environment—indoors or outdoors.
Step 4 Decide if a liquidtight seal is required.
Step 5 Select N.P.T. size and fitting style.
Wire Management Products Technical Data
Kellems®Grips for Strain Relief
Technical Section
T-69
Dimensions in Inches (mm) www.hubbell-wiring.com
Safety And Working Load Factors For Wire Mesh Grips
Examples
Approx. Breaking Strength Max. Rec. Load
Grip Style Lbs. (N) Safety Factor Lbs. (N) Catalog Numbers
Bus Drop 1,000 (4,448) 10 100 (448) 073041279
The maximum recommended working load then is the
tension to be exerted on the grip in application with a
margin of safety to take care of unforeseen and unusual
circumstances.
It is the end-user’s decision to determine how much of a
safety factor is acceptable to him.
Wire Mesh Grip Materials
Material Features Product Group
Galvanized steel wire High strength Strain relief grips
Not subject to continuous outside I-Grips
environment
Stainless steel wire (302-304) High strength Deluxe cord grips
Corrosion resistant Liquidtight, flexible, metal conduit grips
Slightly magnetic UL type A conduit grips
Hose containment grips
Non-metallic strand Superior flex life
Non-conductive Non-metallic deluxe cord grips
Corrosion resistant
Moderate strength
The broad application of Kellems grips on a wide
variety of objects requires that adequate safety
factors be used to establish working loads. The
approximate breaking strength of a Kellems grip
represents an average calculation based on data
established from actual direct tension testing done
in our engineering laboratories.
It is impossible to catalog or guarantee a safety
factor suitable for all applications as operating
conditions are never the same. The tension,
diameter, movement, number of objects gripped,
gripping surface, and the attachments used are just
some of the factors which vary with each
application. These factors, together with the effects
of abrasion, corrosion, prior use or abuse and any
other variables of a specific application, must be
considered by the user and the grip replaced as
appropriate. Where the conditions of the
application are not well defined or known or where
risk of injury to persons or property is involved, a
greater safety factor should be utilized. Should our
opinion be needed, call the factory.
Under normal conditions, Kellems’
recommended factor of safety is five for catalog
listed pulling grips, and ten for catalog listed
support grips. The factory should be consulted
for specific application recommendations
where strength and holding power are
important factors.
Any warranty as to quality, performance or fitness
for use of grips is always premised on the condition
that the published breaking strengths apply only to
new, unused grips, and that such products are
properly stored, handled, used, maintained and
inspected by the user at a frequency appropriate
for the use and condition of the grip.
For grip applications on materials other than those
that the grips have been specifically designed for,
consult the factory.
Technical Data Wire Management Products
Kellems®Grips for Strain Relief
Technical Section
Operating Temperatures
Material Temperature Range
Aluminum –40°F to +300°F (–40°C to +149°C).
Nylon –40°F to +225°F (–40°C to +107°C).
Stainless Steel –60°F to +1000°F (–51°C to +537°C).
Neoprene (bushings) –30°F to +240°F (–34°C to +115°C).
Due to the limiting factors of nylon and neoprene, any complete Deluxe Cord Grip,
Form 1-5 will continuously perform in the range of –30°F to +225°F (–34°C to +107°C).
Hazardous Locations
Product Categories
The product categories listed to the right are Deluxe cord grip, aluminum fitting;
suitable for use in hazardous locations per Class I, Deluxe cord grip, nylon fitting;
Div. 2, Class II, Div. 1 & 2, Class III, Div. 1 & 2. Deluxe cord grip, non-metallic;
Sealtite conduit grips;
Dustight strain relief grips.
Flammability
Non-metallic deluxe cord grips will not support combustion. Listed below are the ratings.
Component Rating
Mesh grip UL 94HB.
Fitting UL 94V-2.
Approvals
UL Listing and CSA Certification are indicated on appropriate product catalog pages. File numbers are listed below.
Agency Control Numbers
Underwriters Laboratories Inc. UL 898 D, UL899D
Wet Locations
Product Categories
The products noted to the right are suitable Deluxe cord grip, aluminum fitting;
for use in wet locations when a listed sealing Deluxe sealing ring cord grip;
ring is used between box and fitting. Deluxe cord grip, non-metallic;
Sealtite conduit grips;
Hubbell non-metallic conduit grips;
Cord connectors;
Hubbell Juniors;
PolyTuff®connectors;
Hubbell sealtite conduit connectors.
T-70 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Kellems®Grips for Strain Relief
Technical Section
Form Size Definition
The term “Form Size” refers to the physical mass or overall dimensions
of a cord connector. Form 1 is the smallest size, Form 8 is the largest
size.
Knockout Holes
Knockout Hole Recommended
N.P.T. Hub Size Min. to Max. Inches (cm)
1/4” .540” to .570” (1.37-1.45)
3/8” .671” to .701” (1.70-1.78)
1/2” .859” to .906” (2.18-2.30)
3/4” 1.094 “ to 1.141” (2.78-2.90)
1” 1.359 “ to 1.406” (3.45-3.57)
11/4” 1.719” to 1.766” (4.37-4.49)
11/2” 1.969” to 2.016” (5.00-5.12)
2” 2.453” to 2.500” (6.23-6.35)
21/2” 2.953 “ to 3.000” (7.50-7.62)
3” 3.578” to 3.625” (9.09-9.21)
Product Data
Deluxe Cord Grips,
Liquidtight for Insulated Cables
Deluxe Cord Grips completely eliminate pull tension on terminals,
control cable arc-of-bend, prevent cord pull-out, and provide a
liquidtight seal. They are offered with either aluminum, stainless steel or
nylon fittings in a variety of configurations and N.P.T. thread sizes.
Additionally, a completely non-metallic product is offered on page T-63.
Application
Deluxe Cord Grips are used indoors or outdoors to prevent cord pull-
out, and where cables are subjected to moisture, splash or submersion.
Specific uses are: wiring enclosures, pendant stations, hand tools,
construction, processing and material handling equipment, pumps,
motors and machine tools.
Benefits
• Prevents cable pull-out.
• Controls cable arc-of-bend.
• Provides a liquidtight seal.
• Corrosion resistant stainless steel mesh with aluminum collar.
T-71
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Kellems®Grips for Strain Relief
Technical Section
Deluxe Cord Grips Fitting Dimensions
Straight Hubbell Connectors
Aluminum, Inches (cm) Nylon, Inches (cm) Stainless Steel, Inches (cm)
FABCDEABCDEABCDE
N.P.T. Throat Throat Throat
Inches Form Dia. Ref. Dia. A/C* A/F* Dia. Ref. Dia. A/C* A/F* A/C* A/F Dia. A/C* A/F*
3/8
”-18 1 .88” .90” .46” .44” .99” .88” 1.00” 1.10” .43” .45” 1.00” .93” 1.01” .88” .90” .46” .45” .87” .75”
(2.24) (2.29) (1.17) (1.12) (2.51) (2.24) (2.54) (2.79) (1.09) (1.14) (2.54) (2.36) (2.57) (2.24) (2.29) (1.17) (1.14) (2.21) (1.90)
1/2
”-14 1 .88” .90” .46” .44” 1.00” .88” 1.00” 1.10” .46” .45” 1.00” .93” • • • • • • •
(2.24) (2.29) (1.17) (1.12) (2.54) (2.24) (2.54) (2.79) (1.17) (1.14) (2.54) (2.36)
1/2
”-14 2 1.13” 1.10” .55” .64” 1.11” 1.00” 1.32” 1.50” .53” .58” 1.25” 1.12” 1.30” 1.13” 1.10” .54” .63” 1.16” 1.00”
(2.87) (2.79) (1.40) (1.63) (2.82) (2.54) (3.35) (3.81) (1.35) (1.47) (3.17) (2.84) (3.30) (2.87) (2.79) (1.37) (1.60) (2.95) (2.54)
1/2
”-14 3 1.38” 1.50” .55” .64” 1.40” 1.25” • • • • • • • • • • • • •
(3.51) (3.81) (1.40) (1.63) (3.56) (3.17)
3/4
”-14 2 1.13” 1.10” .55” .64” 1.29” 1.13” • • • • • • • • • • • • •
(2.87) (2.79) (1.40) (1.63) (3.28) (2.87)
3/4
-14 3 1.38” 1.50” .55” .82” 1.40” 1.25” 1.56” 1.60” .55” .77” 1.44” 1.31” 1.59” 1.38” 1.30” .56” .81” 1.44” 1.25”
(3.51) (3.81) (1.40) (2.08) (3.56) (3.17) (3.96) (4.06) (1.40) (1.96) (3.66) (3.33) (4.04) (3.51) (3.30) (1.42) (2.06) (3.66) (3.17)
1”-11
1/2
3••• •• • •••••• •••••••
1”-11
1/2
4 1.75” 1.60” .71” 1.02” 1.81” 1.62” 1.88” 1.75” .70” 1.01” 1.84” 1.63” 2.02” 1.75” 1.40” .70” 1.03” 1.88” 1.63”
(4.44) (4.06) (1.80) (2.59) (4.60) (4.11) (4.78) (4.44) (1.78) (2.57) (4.67) (4.14) (5.13) (4.44) (3.56) (1.78) (2.62) (4.78) (4.14)
1”-11
1/2
5 2.31” 1.70” .66” 1.01” 2.28” 2.00” • • • • • • • • • • • • •
(5.87) (4.32) (1.68) (2.57) (5.79) (5.08)
1
1/4
”-11
1/2
5 2.31” 1.70” .74” 1.26” 2.28” 2.12” • • • • • • • • • • • • •
(5.87) (4.32) (1.88) (3.20) (5.79) (5.38)
1
1/2
”-11 5 2.31” 1.70” .74” 1.38” 2.28” 2.12” • • • • • • • • • • • • •
(5.87) (4.32) (1.88) (3.51) (5.79) (5.38)
1
1/2
”-11
1/2
6 3.00” 2.20” .75” 1.50” 2.97” 2.75” • • • • • • • • • • • • •
(7.62) (5.59) (1.90) (3.81) (7.54) (6.98)
2”-11
1/2
6 3.00” 2.20” .80” 1.92” 3.24” 3.00” • • • • • • • • • • • • •
(7.62) (5.59) (2.03) (4.88) (8.24) (7.62)
2”-11
1/2
7 3.85” 2.70” .88” 1.94” 4.05” 3.75” • • • • • • • • • • • • •
(9.78) (6.86) (2.24) (4.93) (10.29) (9.52)
2
1/2
”-8 7 3.85” 2.70” 1.30” 2.32” 4.34” 4.02” • • • • • • • • • • • • •
(9.78) (6.86) (3.30) (5.89) (11.02) (10.21)
2
1/2
”-8 8 4.75” 2.70” 1.25” 2.38” 4.86” 4.50” • • • • • • • • • • • • •
(12.06) (6.86) (3.17) (6.05) (12.34) (11.43)
3”-8 7 3.85” 2.70” 1.30” 2.54” 4.34” 4.01” • • • • • • • • • • • • •
(9.78) (6.86) (3.30) (6.45) (11.02) (10.21)
3”-8 8 4.50” 2.70” 1.38” 3.00” 4.86” 4.50” • • • • • • • • • • • • •
(11.43) (6.86) (3.51) (7.62) (12.34) (11.43)
*A/C— Across Corners; A/F—Across Flats
Dimensions shown are approximate and are subject
to change without notice.
A
(Overall)
B Ref.
C
D
F
E
T-72 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Kellems®Grips for Strain Relief
Technical Section
T-73
Dimensions in Inches (mm) www.hubbell-wiring.com
Deluxe Cord Grips Fitting Dimensions
45° Hubbell Connectors
Aluminum, Inches (cm)
FABCDEG
Throat Across Across
N.P.T. Form Ref Ref Dia. Comers Flats Dia.
1/2”-14 2 2.00” 1.90” .550” .560” 1.270” 1.110” 1.125”
(5.08) (4.83) (1.40) (1.42) (3.23) (2.79) (2.86)
3/4”-14 3 2.30” 2.50” .560” .750” 1.480” 1.281” 1.375”
(5.84) (6.53) (1.42) (1.90) (3.76) (3.25) (3.49)
1”-111/24 2.60” 2.80” .700” 1.000” 1.690” 1.500” 1.750”
(6.60) (7.11) (1.78) (2.54) (4.29) (3.81) (4.44)
11/4”-111/25 3.90” 3.90” .740” 1.250” 2.45” 2.125” 2.310”
(9.91) (9.91) (1.88) (3.17) (6.22) (5.40) (5.87)
11/2”-111/25 3.90” 3.90” .740” 1.500” 2.45” 2.125” 2.310”
(9.91) (9.91) (1.88) (3.81) (6.22) (5.40) (5.87)
90° Hubbell Connectors
Aluminum, Inches (cm) Nylon, Inches (cm)
F ABCD E G ABCD E G
Throat Throat
N.P.T. Form Ref Dia. AIC* A/F* Dia. Ref Dia. AIC* A/F Dia.
3/8”-18 1 1.27” 2.00” .460” .440” 1.15” 1.10” .875” • • • • • • •
(3.23) (5.08) (1.17) (1.12) (2.92) (2.79) (2.22)
1/2”-14 2 1.56” 2.30” .500” .546” 1.30” 1.13” 1.125” 1.41” 2.50” .550” .575” 1.23” 1.12” 1.315”
(3.96) (5.84) (1.27) (1.39) (3.30) (2.87) (2.86) (3.58) (6.35) (1.40) (1.46) (3.12) (2.82) (3.34)
3/4”-14 3 1.79” 2.80” .560” .765” 1.49” 1.31” 1.375” 1.65” 2.81” .560” .765” 1.42” 1.29” 1.560”
(4.55) (7.11) (1.42) (1.94) (3.78) (3.33) (3.49) (4.19) (7.14) (1.42) (1.94) (3.61) (3.28) (3.96)
1”-111/24 2.08” 3.20” .700” 1.000” 1.70” 1.50” 1.750” 1.99” 3.30” .700” 1.010” 1.82” 1.60” 1.875”
(5.28) (8.13) (1.78) (2.54) (4.32) (3.81) (4.44) (5.05) (8.38) (1.78) (2.57) (4.62) (4.06) (4.76)
11/4-”111/25 3.18” 4.30” .730” 1.260” 2.47” 2.15” 2.310” • • • • • • •
(8.08) (10.92) (1.85) (3.20) (6.27) (5.46) (5.87)
11/2”-111/25 3.18” 4.30” .750” 1.500” 2.47” 2.15” 2.310” • • • • • • •
(8.08) (10.92) (1.92) (3.81) (6.27) (5.46) (5.87)
2”-111/26 3.51” 5.50” .800” 1.920” 2.98” 2.78” 3.000” • • • • • • •
(8.92) (13.97) (2.03) (4.88) (7.57) (7.06) (7.62)
*A/C - Across Corners; A/F - Across Flats
Dimensions shown are approximate and are subject
to change without notice.
B
Ref.
A
Ref.
D
C
E
F
G
B Ref.
A
D
D
E
F
G
Technical Data Wire Management Products
Kellems®Grips for Strain Relief
Technical Section
T-74 Dimensions in Inches (mm)
www.hubbell-wiring.com
Dimensions shown are approximate and
are subject to change without notice.
A
(Overall)
B Ref.
C (N.P.T. Thread Depth)
D
E
F
Deluxe Cord Grips Fitting Dimensions
Female Hubbell Connectors
Aluminum Inches (cm)
FABCDE
Throat Across Across
N.P.T. Form Dia. Ref Dia. Corners Flats
3/8”-18 1 .88” 1.40” .560” .44” .94” .81”
(2.24) (3.56) (1.42) (1.12) (2.39) (2.06)
1/2”-14 2 1.13” 1.80” .560” .63” 1.15” 1.00”
(2.87) (4.57) (1.42) (1.60) (2.92) (2.54)
3/4”-14 2 1.13” 2.10” .750” .63” 1.44” 1.25”
(2.87) (5.33) (1.90) (1.60) (3.66) (3.17)
1”-111/24 1.75” 2.30” .880” 1.10” 1.88” 1.63”
(4.44) (5.84) (2.24) (2.79) (4.78) (4.14)
1 1/4”-111/25 2.31” 2.80” .950” 1.43” 2.64” 2.29”
(5.87) (7.11) (2.41) (3.63) (6.71) (5.82)
1 1/2”-111/25 2.31” 2.80” .950” 1.43” 2.64” 2.29”
(5.87) (7.11) (2.41) (3.63) (6.71) (5.82)
Product Data
Dust Tight Strain Relief Grips for Insulated Cables
Kellems Strain Relief Grips connect flexible cord or bus drop cable to
electrical enclosures. For indoor use only, they are available with either
insulated or non-insulated aluminum fittings, and feature single weave,
galvanized steel mesh grips with patented wide range mesh
construction. They come with a locknut and a neoprene gasket that
provides a dust tight seal.
Application
Used to connect electrical cable to power boxes, cabinets, panel
boards, power centers, machine tools and with bus drop systems.
Benefits
• Prevents cord or cable pull-out. • Patented mesh construction.
• Provides a dust tight seal. • One piece design.
• Easy installation.
I-Grips for Insulated Cables
Kellems I-Grips are made of high strength, plastic coated galvanized
steel strand. They are offered in six sizes to fit all cable diameters
used with Hubbell Insulgrip®Kellems l-Grips will control cable arc-of-
bend and reduce high pull tensions from being transmitted to the
wiring terminals.
Application
Kellems I-Grips will fit 2 wire, 3 wire, 4 wire and 5 wire Hubbell
Insulgrip plugs and connector bodies. The eye tabs fit under the nylon
cord clamp and the screws slide through the eyelets, securing the grip
in place.
I-Grips can be used on any Insulgrip cord set which requires cable,
arc-of-bend control or heavy duty strain relief. Cord sets used at in-
door construction sites or for plant maintenance jobs are examples.
These grips are for indoor use only.
Benefits
• Easily attached to Insulgrip plugs • Provides heavy duty strain relief.
and connector bodies.
• Fits all sizes. • Controls cable arc-of-bend.
Note: I-Grips should not be used on Insulgrip devices when “Seal-Tite®” weatherproof
covers are to be installed.
Wire Management Products Cord Connector Features and Benefits
Cord Connectors
Features and Benefits
Machined threads provide a strong positive seal.
The tapered interior dome easily drives the bushing
into the connector body.
The patented GOTHCA® ring incorporates
a split hinge design to prevent friction and
provide strain relief, also color-coded for
sizing identification.
Lubricated neoprene bushing compresses easily
for a liquidtight seal and added pull-out protection.
The connector body is a one-piece design with
machined threads. A tapered interior seats the
bushing evenly for a liquidtight seal.
T-75
Dimensions in Inches (mm) www.hubbell-wiring.com
Hubbell has the broadest line and the widest
choice of materials in the industry. N.P.T. hub sizes
from 1/4” to 3” in straight male end, 90°, 45°, female
and underground feed connectors. They are
available in your choice of aluminum, plated steel,
nylon and stainless steel.
Hubbell offers a full line of machined aluminum
cord connectors in N.P.T. hub sizes 1/4” through 1”
and cast aluminum 1” to 3”. They provide durable
performance and a clean attractive look without
adding unwanted weight. N.P.T. hub sizes 1/4” to 1”
feature an attractive knurled finish which makes
them easy to handle and maintain a U.L. listing by
hand tightening.
The zinc-plated steel cord connectors offers the
strength of steel and the corrosion resistance of
zinc-plating. These heavy-duty connectors hold up
to most manufacturing chemicals including acid
solutions, solvents and other corrosive materials.
Their machined steel nut and body allows for
tightening the compression nut and N.P.T. hub
without worrying about stripping the threads. For
larger size cord, N.P.T. hub sizes 1” to 2”, Hubbell
utilizes malleable iron connectors which provide
excellent holding and liquidtight performance.
Hubbell’s nylon cord connectors resist most
common industrial corrosives and provide highly
effective pullout protection in a lightweight design.
They are ideal for any application where weight,
conductivity or corrosion may be an issue. They’re
available in N.P.T. hub sizes from 1/4” to 1”.
Stainless steel cord connectors provide superior
strength and corrosion resistance for industrial and
military applications. They are machined from 300
series stainless steel and come in 1/4” through 1”,
N.P.T. hub sizes.
Cord Connectors Wire Management Products
Cord Connectors
Straight Male
Form Size 1-4
T-76 Dimensions in Inches (mm)
www.hubbell-wiring.com
Machined
Zinc-Plated Steel
Machined
Aluminum
UL Listed to Type 4, 4X, 12 and Type 13
N.P.T. Cord Dia. Machined
Hub Inches Form Color Machined Zinc-Plated Stainless Nylon
Size (mm) Size Code Aluminum Steel Steel Gray Black
.06”-.13” Green • • • SHC1001CR •
(1.6-3.2)
.13”-.19” Orange SHC1002 ••SHC1002CR •
(3.2-4.7)
1/4” .19”-.25” F1 Red SHC1003 •SHC1003SS SHC1003CR •
(4.7-6.3)
.25”-.31” Black SHC1004 •SHC1004SS SHC1004CR •
(6.3-7.9)
.31”-.38” White SHC1005** ••SHC1005CR SHC2005CR
(7.9-9.5)
.38”-.44” Blue • • • SHC1006CR •
(9.5-11)
.06”-.13” Green SHC1007 ••• •
(1.6-3.2)
.13”-.19” Orange SHC1008 SHC1008ZP •SHC1008CR SHC2008CR
(3.2-4.7)
3/8” .19”-.25” F1 Red SHC1009 •SHC1009SS SHC1009CR •
(4.7-6.3)
.25”-.31” Black SHC1010 SHC1010ZP •SHC1010CR SHC2010CR
(6.3-7.9)
.31”-.38” White SHC1011 •SHC1011SS SHC1011CR SHC2011CR
(7.9-9.5)
.38”-.44” Blue SHC1012 SHC1012ZP SHC1012SS SHC1012CR SHC2012CR
(9.5-11.0)
.19”-.25” Red SHC1015 ••• •
(4.7-6.3)
1/2” .25”-.31” F1 Black SHC1016 ••• •
(6.3-7.9)
.31”-.38” White SHC1017 ••• •
(7.9-9.5)
.38”-.44” Blue SHC1018 ••• •
(9.5-11.0)
.06”-.13” Green SHC1019 ••SHC1019CR •
(1.6-3.2)
.13”-.19” Orange SHC1020 SHC1020ZP SHC1020SS SHC1020CR •
(3.2-.4.7)
1/2” .19”-.25” F2 Red SHC1021 SHC1021ZP SHC1021SS SHC1021CR SHC2021CR
(4.7-6.3)
.25”-.38” White SHC1022 SHC1022ZP SHC1022SS SHC1022CR SHC2022CR
(6.3-.9.7)
.38”-.50” Blue SHC1023 SHC1023ZP SHC1023SS SHC1023CR SHC2023CR
(9.7-12.7)
.50”-.62” Brown SHC1024 SHC1024ZP SHC1024SS SHC1024CR** SHC2024CR**
(12.7-15.9)
.38”-.50” Blue SHC1025 ••• •
(9.7-12.7)
.50”-.63” Brown SHC1026 ••• •
(12.7-15.9)
1/2” .63”-.75” F3 Yellow SHC1027** SHC1027ZP** •• •
(15.9-19.0)
.75”-.88” Orchid SHC1028** SHC1028ZP** •• •
(19.0-22.2)
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring shown on page T-83.
**Cable jacket may have to be stripped to pass through connector body.
IP66*
SUITABILITY
Wire Management Products Cord Connectors
Cord Connectors
Straight Male
Form Size 1-4
Black Nylon
Gray Nylon
Stainless
Steel
UL Listed to Type 4, 4X, 12 and Type 13
N.P.T. Cord Dia. Machined
Hub Inches Form Color Machined Zinc-Plated Stainless Nylon
Size (mm) Size Code Aluminum Steel Steel Gray Black
.06”-.13” Green SHC1029 ••• •
(1.6-3.2)
.13”-.19” Orange SHC1030 SHC1030ZP •• •
(3.2-4.7)
3/4” .19”-.25” F2 Red SHC1031 SHC1031ZP •• •
(4.7-6.3)
.25”-.38” White SHC1032 SHC1032ZP • • •
(6.3-9.7)
.38”-.50” Blue SHC1033 SHC1033ZP •• •
(9.7-12.7)
.50”-.63” Brown SHC1034 SHC1034ZP •• •
(12.7-15.9)
.38”-.50” Blue • SHC1035ZP SHC1035SS SHC1035CR SHC2035CR
(9.5-12.7)
3/4” .50”-.63” F3 Brown SHC1036 SHC1036ZP SHC1036SS SHC1036CR SHC2036CR
(12.7-15.9)
.63”-.75” Yellow SHC1037 SHC1037ZP SHC1037SS SHC1037CR SHC2037CR
(15.9-19.0)
.75”-.88” Orchid SHC1038**SHC1038ZP** SHC1038SS** SHC1038CR** SHC2038CR**
(19.0-22.2)
1” .50”-.63” F3 Brown • SHC1097ZP •• •
(12.7-15.9)
.63”-.75” Yellow • SHC1098ZP •• •
(15.9-19.0)
.75”-.88” Orchid • SHC1099ZP •• •
(19.0-22.2)
.38”-.50” Blue SHC1039 ••SHC1039CR •
(9.7-12.7)
.50”-.63” Brown SHC1040 ••SHC1040CR •
(12.7-15.9)
1” .63”-.75” F4 Yellow SHC1041 •SHC1041SS SHC1041CR SHC2041CR
(15.9-19.0)
.75”-.88” Orchid SHC1042 •SHC1042SS SHC1042CR SHC2042CR
(19.0-22.2)
.88”-1.00” Gray SHC1043 SHC1043ZP •SHC1043CR SHC2043CR
(22.2-25.4)
1.00”-1.13” Pink SHC1044**•SHC1044SS** SHC1044CR** SHC2044CR**
(25.4-28.6)
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring shown on page T-83.
**Cable jacket may have to be stripped to pass through connector body.
Form 4 aluminum and plated steel nuts are machined, bodies are cast aluminum.
T-77
Dimensions in Inches (mm) www.hubbell-wiring.com
IP66*
SUITABILITY
Cord Connectors Wire Management Products
Cord Connectors
Straight Male
Form Size 5-8
T-78 Dimensions in Inches (mm)
www.hubbell-wiring.com
Cast Aluminum
Malleable Iron
Cast Aluminum
UL Listed to Type 4, 4X, 12 and Type 13
N.P.T. Cord Dia. Form
Hub Size Inches (mm) Size Cast Aluminum Malleable Iron
†
.88”-1.00” (22.2-25.4) SHC1046 •
1” 1.00”-1.13” (25.4-28.6) F5 SHC1047** •
1.13”-1.25” (28.6-31.7) SHC1048** •
1.25”-1.38” (31.7-34.9) SHC1049** •
.75”-.88” (19.0-22.2) SHC1050 •
.88”-1.00” (22.2-25.4) SHC1051 •
11/4” 1.00”-1.13” (25.4-28.6) F5 SHC1052 SHC1052ZP
1.13”-1.25” (28.6-31.7) SHC1053 SHC1053ZP
1.25”-1.38” (31.7-34.9) SHC1054** SHC1054ZP
.75”-.88” (19.0-22.2) SHC1055 •
.88”-1.00” (22.2-25.4) SHC1056 •
11/2” 1.00”-1.13” (25.4-28.6) F5 SHC1057 SHC1057ZP
1.13”-1.25” (28.6-31.7) SHC1058 SHC1058ZP
1.25”-1.38” (31.7-34.9) SHC1059 SHC1059ZP
1.38”-1.50” (34.9-38.1) SHC1061 •
11/2” 1.50”-1.63” (38.1-41.3) F6 SHC1062** •
1.63”-1.75” (41.3-44.4) SHC1063** •
1.75”-1.88” (44.4-47.6) SHC1064** •
1.25”-1.38” (31.7-34.9) SHC1065 •
1.38”-1.50” (34.9-38.1) SHC1066 •
2” 1.50”-1.63” (38.1-41.3) F6 SHC1067 •
1.63”-1.75” (41.3-44.4) SHC1068 •
1.75”-1.88” (44.4-47.6) SHC1069 •
1.69”-1.81” (42.9-46.0) SHC1070 •
1.81”-1.94” (46.0-49.2) SHC1071 •
2” 1.94”-2.06” (49.2-52.4) F7 SHC1072** •
2.06”-2.19” (52.4-55.6) SHC1073** •
2.19”-2.31” (55.6-58.7) SHC1074** •
1.69”-1.81” (42.9-46.0) SHC1076 •
1.81”-1.94” (46.0-49.2) SHC1077 •
21/2” 1.94”-2.06” (49.2-52.4) F7 SHC1078 •
2.06”-2.19” (52.4-55.6) SHC1079 •
2.19”-2.31” (55.6-58.7) SHC1080 •
2.31”-2.44” (58.7-61.9) SHC1081** •
1.69”-1.81” (42.9-46.0) SHC1086 •
1.81”-1.94” (46.0-49.2) SHC1087 •
3” 1.94”-2.06” (49.2-52.4) F7 SHC1088 •
2.06”-2.19” (52.4-55.6) SHC1089 •
2.19”-2.31” (55.6-58.7) SHC1090 •
2.31”-2.44” (58.7-61.9) SHC1091 •
2.44”-2.63” (61.9-66.7) SHC1092 •
2.63”-2.81” (66.7-71.4) SHC1093 •
3” 2.81”-3.00” (71.4-76.2) F8 SHC1094 •
3.00”-3.25” (76.2-82.5) SHC1095** •
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring shown on page T-83.
**Cable jacket may have to be stripped to pass through connector body.
F5 and larger will not be color coded.
IP66*
SUITABILITY
Wire Management Products Cord Connectors
Cord Connectors
45° Male
Form Size 2-5
Cast
Aluminum
Machined
Zinc-Plated Steel∆
Machined
Aluminum
†
UL Listed to Type 4, 4X, 12 and Type 13
Form Size 1-5
N.P.T. Machined
Hub Cord Dia. Form Color Machined Zinc-Plated Cast
Size Inches (mm) Size Code Aluminum
†
Steel
Aluminum
.19”-.25” (4.7-6.3) F2 Red VHC1021 ••
1/2” .25”-.38” (6.3-9.7) White VHC1022 VHC1022ZP •
.38”-.50” (9.7-12.7) Blue VHC1023 VHC1023ZP •
.50”-.63” (12.7-15.9) Brown VHC1024** VHC1024ZP** •
.38”-.50” (9.7-12.7) Blue VHC1035 ••
3/4” .50”-.63” (12.7-15.9) F3 Brown VHC1036 ••
.63”-.75” (15.9-19.0) Yellow VHC1037** ••
1” .63”-.75” (15.9-19.0) Yellow VHC1041 ••
.75”-.88” (19.0-22.2) F4 Orchid VHC1042 ••
11/4” 1.00”-1.13” (25.4-28.6) • • VHC1052
1.13”-1.25” (28.6-31.7) F5 • • VHC1053**
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-83.
** Cable jacket may have to be stripped to pass through connector body.
†Nuts are machined aluminum and bodies are cast aluminum.
Nuts are machined zinc-plated steel and bodies are malleable iron, cadmium
plated.
T-79
Dimensions in Inches (mm) www.hubbell-wiring.com
IP66*
SUITABILITY
Cord Connectors Wire Management Products
Cord Connectors
90° Male
Form Size 1-6
UL Listed to Type 4, 4X, 12 and Type 13
Form 1-6
N.P.T. Cord Machined
Hub Dia. Form Color Machined Zinc-Plated Nylon Nylon Cast
Size Inches (mm) Size Code Aluminum
†
SteelGray Black Aluminum
.25”-.31” (6.3-7.9) Black NHC1010 ••••
3/8” .31”-.38” (7.9-9.5) F1 White NHC1011 ••••
.38”-.44” (9.5-11.0) Blue NHC1012 ••••
.06”-.13” (1.6-3.2) Green • • • • •
.13”-.19” (3.2-4.7) Orange NHC1020 •NHC1020CR ••
1/2” .19”-.25” (4.7-6.3) F2 Red NHC1021 NHC1021ZP NHC1021CR ••
.25”-.38” (6.3-9.7) White NHC1022 NHC1022ZP NHC1022CR NHC2022CR •
.38”-.50” (9.7-12.7) Blue NHC1023 NHC1023ZP NHC1023CR NHC2023CR •
.50”-.63” (12.7-15.9) Brown NHC1024** NHC1024ZP** NHC1024CR** NHC2024CR** •
.38”-.50” (9.7-12.7) Blue NHC1035 NHC1035ZP NHC1035CR ••
3/4” .50”-.63” (12.7-15.9) F3 Brown NHC1036 NHC1036ZP NHC1036CR ••
.63”-.75” (15.9-19.0) Yellow NHC1037 NHC1037ZP NHC1037CR ••
.75”-.88” (19.0-22.2) Orchid NHC1038 NHC1038ZP NHC1038CR ••
.50”-.63” (12.7-15.9) Brown NHC1040 NHC1040ZP •• •
.63”-.75” (15.9-19.0) Yellow NHC1041 NHC1041ZP NHC1041CR NHC2041CR •
1” .75”-.88” (19.0-22.2) F4 Orchid NHC1042 NHC1042ZP NHC1042CR NHC2042CR** •
.88”-1.00” (22.2-25.4) Gray NHC1043** •NHC1043CR NHC2043CR** •
1.00”-1.13” (25.4-28.7) Pink NHC1044** ••••
.88”-1.00” (22.2-25.4) • • • • • NHC1051
11/4” 1.00”-1.13” (25.4-28.6) F5 • • • • • NHC1052
1.13”-1.25” (28.6-31.7) • • • • • NHC1053**
1.25”-1.38” (31.7-.349) • • • • • NHC1054**
1.00”-1.13” (25.4-28.6) • • • • • NHC1057
11/2” 1.13”-1.25” (28.6-31.7) F5 • • • • • •
1.25”-1.38” (31.7-34.9) • • • • • NHC1059
2” 1.38”-1.50” (34.9-38.1) F6 • • • • • NHC1066
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
* IP66 Suitability when used with optional metal clad O-ring shown on page T-83.
** Cable jacket may have to be stripped to pass through connector body.
† Nuts are machined aluminum and bodies are cast aluminum.
Compression nuts are machined zinc-plated steel and bodies are zinc-plated malleable iron.
Cast Aluminum
Black Nylon
Gray Nylon
Machined
Zinc-Plated Steel∆
Machined
Aluminum†
T-80 Dimensions in Inches (mm)
www.hubbell-wiring.com
IP66*
SUITABILITY
Wire Management Products Cord Connectors
Cord Connectors
Straight Female and Underground Feeder
Black Nylon
Gray Nylon
Zinc-Plated Steel
Machined Aluminum
Machined
Aluminum
Form 1-4
N.P.T.
Hub Cord Dia. Form Color Machined
Size Inches (mm) Size Code Aluminum
1/2”
.25”-.38” (6.3-9.7) F2 White FHC1022
.38”-.50” (9.7-12.7) Blue FHC1023
3/4”
.38”-.50” (9.7-12.7) F2 Blue FHC1033
.50”-.63” (12.7-15.9) Brown FHC1034
1” .75”-.88” (19.0-22.2) F4 Orchid FHC1042
†
.88”-1.00” (22.2-25.4) Gray FHC1043
†
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
*Cable jacket may have to be stripped to pass through connector body.
†Nuts are machined aluminum and bodies are cast aluminum.
Underground Feeder Connectors
N.P.T. UF** Machined
Hub Diameter Wire Machined Zinc-Plated Nylon Nylon
Size Inches (mm) Size Aluminum Steel Gray Black
1/2
” .2”x.4” min
(5.1 x 10.2)
2 # 14,
.25”-.55” max
(6.3 x 14.0)
2 # 12, UFC0001 UFC0001ZP UFC0001CR UFC2001CR
2 # 10.
3/4
” .2”x.4” min (5.1x10.2) 2 # 14,
.25”-.55” max (6.3x14.0) 2 # 12, UFC0002 •• •
2 # 10.
3/4
” .2”x.6” min (5.1x15.2) 3 # 14,
.26”x.78” max (6.6x19.8) 3 # 12, UFC0003 •UFC0003CR UFC2003CR
3 # 10.
Note: See pages T-87 to T-98 for additional technical data and dimensional drawings.
*IP66 Suitability when used with optional metal clad O-ring shown below.
**Wire sizes vary among manufacturers.
T-81
Dimensions in Inches (mm) www.hubbell-wiring.com
IP66*
SUITABILITY
Cord Connectors & Accessories Wire Management Products
Non-metallic Cord Connectors
Straight Male N.P.T. & PG Thread
Low Profile
T-82 Dimensions in Inches (mm)
www.hubbell-wiring.com
LNPG29BPK25
SECP29G
SEC100B
Low Profile N.P.T. Cord Connectors
N.P.T. Cord Dia. Catalog
Hub Size Inches (mm) Color Numbers
3/8” .20”-.32” (5.1-8.13) Gray SEC38G
3/8” .20”-.32” (5.1-8.13) Black SEC38B
1/2” .24”-.47” (6.1-12) Gray SEC50G
1/2” .24”-.47” (6.1-12) Black SEC50B
3/4” .47”-.71” (12-18) Gray SEC75G
3/4” .47”-.71” (12-18) Black SEC75B
1” .67”-.98” (17-25) Gray SEC100G
1” .67”-.98” (17-25) Black SEC100B
Note: See pages T-87 to T-91 for additional technical data and dimensional drawings.
Low Profile PG Cord Connectors
Cord Dia. Catalog
Hub Size Inches (mm) Color Numbers
PG7 .18”-.26” (4.5-6.6) Gray SECP7G
PG7 .18”-.26” (4.5-6.6) Black SECP7B
PG9 .20”-.32” (5.1-8.13) Gray SECP9G
PG9 .20”-.32” (5.1-8.13) Black SECP9B
PG11 .22”-.39” (5.6-9.9) Gray SECP11G
PG11 .22”-.39” (5.6-9.9) Black SECP11B
PG13.5 .47”-.71” (12-18) Gray SECP13G
PG13.5 .47”-.71” (12-18) Black SECP13B
PG16 .32”-.55” (8.13-14) Gray SECP16G
PG16 .32”-.55” (8.13-14) Black SECP16B
PG21 .47”-.71” (12-18) Gray SECP21G
PG21 .47”-.71” (12-18) Black SECP21B
PG29 .67”-.98” (17-25) Gray SECP29G
PG29 .67”-.98” (17-25) Black SECP29B
PG36 .79”-1.26” (20-32) Gray SECP36G
PG36 .79”-1.26” (20-32) Black SECP36B
Note: See pages T-87 to T-91 for additional technical data and dimensional data.
PG Non-Metallic Locknuts
Hub Size Color Catalog Numbers
PG7 Black LNPG7BPK100
PG9 Black LNPG9BPK100
PG11 Black LNPG11BPK100
PG13.5 Black LNPG13BPK100
PG16 Black LNPG16BPK100
PG21 Black LNPG21BPK100
PG29 Black LNPG29BPK25
PG36 Black LNPG36BPK25
Notes: Catalog numbers above with “PK100” suffix, i.e. LNPG7BPK100,
are bulk packed 100 per carton.
Catalog numbers above with “PK25” suffix, i.e. LNPG29BPK25,
are bulk packed 25 per carton.
IP68*
SUITABILITY
Wire Management Products Accessories
Cord Connectors
Accessories
Cord Connector Parts
N.P.T. Cord Dia. Form Bushing GOTCHA
®
Ring
Hub Size Inches (mm) Size Catalog Numbers Color Code Catalog Numbers
1/4”, 3/8”, 1/2” .062”-.125” (1.58-3.17) F1 31518101BPK100 Green 31648035GPK100
.125”-.187” (3.17-4.76) 31518102BPK100 Orange 31648036GPK100
.187”-.250” (4.76-6.35) 31518103BPK100 Red 31648037GPK100
.250”-.312” (6.35-7.93) 31518104BPK100 Black 31648038GPK100
.312”-.375” (7.93-9.50) 31518105BPK100 White 31605010GPK100
.375”-.437” (9.50-11.1) 31518106BPK100 Blue 31648039GPK100
1/2”, 3/4” .062”-.125” (1.58-3.17) F2 -Green -
.125”-.187” (3.17-4.76) -Orange -
.187”-.250” (4.76-6.35) 31518110BPK100 Red 31648042GPK100
.250”-.375” (6.35-9.50) 31518111BPK100 White 31605015G
.375”-.500” (9.50-12.7) 31518112BPK100 Blue 31648043GPK100
.500”-.625” (12.7-15.8) 31518113BPK100 Brown 31648044GPK100
1/2”, 3/4” .375”-.500” (9.50-12.7) F3 31518116BPK100 Blue 31648045GPK100
.500”-.625” (12.7-15.8) 31518117BPK100 Brown 31648046GPK100
.625”-.750” (15.8-19.0) 31518118BPK100 Yellow 31648047GPK100
.750”-.875” (19.0-22.2) 31518119BPK100 Orchid 31648048GPK100
1” .375”-.500” (9.50-12.7) F4 -Blue -
.500”-.625” (12.7-15.8) 31518123BPK100 Brown 31648050GPK100
.625”-.750” (15.87-19.0) -Yellow 31648051GPK100
.750”-.875” (19.0-22.2) 31518125BPK100 Orchid 31648052GPK100
.875”-1.00” (22.2-25.4) 31518126BPK100 Gray 31648053GPK100
1.00”-1.125” (25.4-28.5) 31518127BPK100 Pink 31648054GPK100
Note: Catalog numbers above with “PK100” suffix, i.e. 31518101BPK100, are bulk packed 100 per carton.
T-83
Dimensions in Inches (mm) www.hubbell-wiring.com
Locknuts — Steel and Non-metallic
N.P.T. Hub Size Zinc-Plated Steel Non-metallic
1/4”• 31622001LPK50
3/8”• 31622002LPK50
1/2”00322001LPK50 31622003LPK50
3/4”00322002LPK50 31622007LPK50
1” 00322003LPK50 31622008LPK50
11/4”00322004LPK50 •
11/2”00322005LPK50 •
Notes: Catalog numbers above with “PK50” suffix, i.e. 00322001LPK50,
are bulk packed 50 per carton.
See page T-96 for additional technical data and dimensional drawings.
Metal Clad Sealing O-Rings
N.P.T. Hub Size Catalog Numbers
1/2”20509001
3/4”20509002
1” 20509003
11/4”20509004
11/2”20509005
2” 20509006
21/2”20509007
3” 20509008
Note: See page T-96 for additional technical data and dimensional drawings.
Zinc-Plated Steel Locknut
s
Non-metallic Locknuts
Metal Clad Sealing O-Rings
Hubbell Juniors®
Hubbell Juniors®Wire Management Products
Wire Management Products Features and Benefits
Hubbell Juniors®Miniature Cord Connectors
Features and Benefits
Hubbell Juniors are a miniature liquidtight version of
the full-sized Hubbell cord connectors. They feature
the same GOTCHA®ring technology and neoprene
bushings. They also come with or without a nylon
spiral for arc-of-bend control and longer cord life.
They are available in 1/4”, 3/8”, and 1/2” N.P.T. sizes in
both gray and black.
Nylon spiral provides arc-of-bend control for cord protection.
Nylon compression nut has a tapered interior dome
to easily drive the bushing into the connector body.
Patented GOTCHA® ring incorporates a
split hinge design to prevent friction and
provide strain relief.
Lubricated neoprene bushing compresses evenly for a
liquidtight seal and added pull-out protection.
Nylon connector body is a one piece design with a tapered
interior that seals the bushing evenly for a positive seal.
Threaded hexagon shaped nylon locknut secures tightly
and is also corrosion resistant.
T-85
Dimensions in Inches (mm) www.hubbell-wiring.com
Hubbell Juniors®Wire Management Products
Miniature Nylon Cord Connectors
HUBBELL JUNIORS®
T-86 Dimensions in Inches (mm)
www.hubbell-wiring.com
Black Snap-In
Cord Connector
Gray Snap-In
Cord Connector
Black Cord Connector with Spira
l
Gray Cord Connector with Spir
Black Cord Connector
Gray Cord Connector
Miniature Nylon Cord Connector
Cord Dia.
N.P.T. Range
Hub Size Inches (mm) Gray Black
.08”-.14” (1.9-3.4) HJ1001GPK25 HJ1001BPK25
1/4” .14”-.20” (3.4-5.1) HJ1002GPK25 HJ1002BPK25
.20”-.27” (5.1-6.7) HJ1003GPK25 HJ1003BPK25
.15”-.21” (3.7-5.3) HJ1004GPK25 HJ1004BPK25
3/8” .21”-.28” (5.3-7.0) HJ1005GPK25 HJ1005BPK25
.28”-.34” (7.0-8.6) HJ1006GKP25 HJ1006BKP25
.06”-.13” (1.6-3.2) HJ1055GPK25 HJ1055BPK25
.13”-.19” (3.2-4.7) HJ1056GPK25 HJ1056BPK25
1/2” .19”-.25” (4.7-6.3) HJ1057GPK25 HJ1057BPK25
.25”-.31” (6.3-7.9) HJ1058GPK25 HJ1058BPK25
.31”-.38” (7.9-9.5) HJ1059GPK25 HJ1059BPK25
.38”-.44” (9.5-11.1) HJ1060GPK25 HJ1060BPK25
Miniature Nylon Cord Connector with Spiral
Cord Dia.
N.P.T. Range
Hub Size Inches (mm) Gray Black
.08”-.14” (1.9-3.4) HJ1010GPK25 HJ1010BPK25
1/4” .14”-.20” (3.4-5.1) HJ1011GPK25 HJ1011BPK25
.20”-.27” (5.1-6.7) HJ1012GPK25 HJ1012BPK25
.15”-.21” (3.7-5.3) HJ1013GPK25 HJ1013BPK25
3/8” .21”-.28” (5.3-7.0) HJ1014GPK25 HJ1014BPK25
.28”-.34” (7.0-8.6) HJ1015GPK25 HJ1015BPK25
.13”-.19” (3.2-4.7) HJ1038GPK25 HJ1038BPK25
.19”-.25” (4.7-6.3) HJ1039GPK25 HJ1039BPK25
1/2” .25”-.31” (6.3-7.9) HJ1040GPK25 HJ1040BPK25
.31”-.38” (7.9-9.5) HJ1041GPK25 HJ1041BPK25
.38”-.44” (9.5-11.1) HJ1042GPK25 HJ1042BPK25
Miniature Nylon Snap-In Cord Connector
Cord
Diameter
Range For Chassis
Inches (mm) Thickness Gray Black
.22”-.27” (5.6-6.9) .10” (2.5) Max HS1001GPK25 HS1001BPK25
.28”-.32” (7.1-8.1) .10” (2.5) Max HS1002GPK25 HS1002BPK25
.30”-.36” (7.6-9.1) .13” (3.2) Max HS1003GPK25 HS1003BPK25
.32”-.43” (8.1-10.9) .13” (3.2) Max HS1004GPK25 HS1004BPK25
Notes: Catalog numbers above with “PK25” suffix, i.e. HJ1001GPK25,
are bulk packed 25 per carton.
See pages T-97 and T-98 for additonal technical data and dimensional
drawings.
Gray Cord Connector with Spiral
Wire Management Products Technical Data
Cord Connectors
Technical Data
Operating Temperatures
Material Temperature Range
Aluminum -40°F to +300°F (-40°C to +149°C)
Nylon (connectors and GOTCHA®rings) -40°F to +225°F (-40°C to +107°C)
Plated steel* -60°F to +1000°F (-51°C to +537°C)
Stainless steel* -60°F to +1000°F (-51°C to +537°C)
Neoprene (bushings) -30°F to +240°F (-34°C to +115°C)
*Due to the limiting factors of nylon and neoprene, any complete cord connector with a GOTCHA ring, Form 1-5, will continuously
perform in the range of -30°F to +225°F (-34°C to +107°C).
Cord connectors without GOTCHA rings, Form 6-8, will continuously operate in the range -30°F to +240°F (-34°C to +115°C) due to
the limiting factor of neoprene.
Hazardous Locations
Hubbell cord connectors are suitable for use in hazardous locations per Class I Div. 2, Class II Div. 1 & 2, Class Ill Div. 1 & 2 NEC
Reference 501-4(b), 502-4(a), 502-4(b), 503-3(a), and 503-3(b).
Flammability
Hubbell nylon cord connectors have a UL 94-V2 rating.
Approvals
Agency
UL Listed in accordance with Standard 514B.
CSA Certified.
United States Coast Guard Approved, Title 46-Part 111.
Form Size Definition
The term “Form Size” refers to the physical overall size of a cord connector.
Form 1 is the smallest size.
Form 8 is the largest size.
Knockout Holes
Knockout Hole Recommended
N.P.T. Min. to Max.
Hub Size Inches (mm)
1/4” .54”-.57” (13.7-14.5)
3/8” .67”-.70” (17.0-17.8)
1/2” .86”-.91” (21.8-23.0)
3/4” 1.09”-1.14” (27.8-29.0)
1” 1.36”-1.41” (34.5-35.7)
11/4” 1.72”-1.77” (43.7-44.9)
11/2” 1.97”-2.02” (50.0-51.2)
2” 2.45”-2.50” (62.3-63.5)
21/2” 2.95”-3.00” (75.0-76.2)
3” 3.58”-3.63” (90.9-92.1)
T-87
Dimensions in Inches (mm) www.hubbell-wiring.com
SECP29G
N.P.T - PG Thread Low Profile Connectors
Specifications
Material: Polyamide
Sealing Grommet: Neoprene
Temperature Range: -30°C to 100°C.
Cord Connectors are Halogen and Silicon free.
Protection Class: IP67.
Flame Retardant: UL 94V-0.
Listings/Certifications: UL 514B, VDE 0619, CSA C22.2 No. 18.
Technical Data Wire Management Products
Cord Connectors
Technical Data
Dimensional Charts
Straight Hubbell Connectors
Aluminum Inches (mm) Nylon Inches (mm)
F ABCD E ABCD E
Throat Throat
N.P.T. Form Dia. Ref. Dia. A/C* A/F* Dia. Ref. Dia. A/C* A/F*
1/4”-18 1 .88” .90” .46” .32” .99” .88” 1.00” 1.10” .43” .33” .1.00” .93”
(22.4) (22.9) (11.7) (8.1) (25.1) (22.4) (25.4) (27.9) (10.9) (8.4) (25.4) (23.6)
3/8”-18 1 .88” .90” .46” .44” .99” .88” 1.00” 1.10” .43” .45” 1.00” .93”
(22.4) (22.9) (11.7) (11.2) (25.1) (22.4) (25.4) (27.9) (10.9) (11.4) (25.4) (23.6)
1/2”-14 1 .88” .90” .46” .44” 1.00” .88” 1.00” 1.10” .46” .45” 1.00” .93”
(22.4) (22.9) (11.7) (11.2) (25.4) (22.4) (25.4) (27.9) (11.7) (11.4) (25.4) (23.6)
1/2”-14 2 1.13” 1.10” .55” .64” 1.11” 1.00” 1.32” 1.50” .53” .58” 1.25” 1.12”
(28.7) (27.9) (14.0) (16.3) (28.2) (25.4) (33.5) (38.1) (13.5) (14.7) (31.7) (28.4)
1/2”-14 3 1.38” 1.50” .55” .64” 1.40” 1.25” • • • • • •
(35.1) (38.1) (14.0) (16.3) (35.6) (31.7)
3/4”-14 2 1.13” 1.10” .55” .64” 1.29” 1.13” • • • • • •
(28.7) (27.9) (14.0) (16.3) (32.8) (28.7)
3/4”-14 3 1.38” 1.50” .55” .82” 1.40” 1.25” 1.56” 1.60” .55” .77” 1.44” 1.31”
(35.1) (38.1) (14.0) (20.8) (35.6) (31.7) (39.6) (40.6) (14.0) (19.6) (36.6) (33.3)
1”-111/24 1.75” 1.60” .71” 1.02” 1.81” 1.62” 1.88” 1.75” .70” 1.01” 1.84” 1.63”
(44.4) (40.6) (18.0) (25.9) (46.0) (41.1) (47.8) (44.4) (17.8) (25.7) (46.7) (41.4)
1”-111/25 2.31” 1.70” .66” 1.01” 2.28” 2.00” • • • • • •
(58.7) (43.2) (16.8) (25.7) (57.9) (50.8)
11/4”-111/25 2.31” 1.70” .74” 1.26” 2.28” 2.12” • • • • • •
(58.7) (43.2) (18.8) (32.0) (57.9) (53.8)
11/2”-111/25 2.31” 1.70” .74” 1.38” 2.28” 2.12” • • • • • •
(58.7) (43.2) (18.8) (35.1) (57.9) (53.8)
11/2”-111/26 3.00” 2.20” .75” 1.50” 2.97” 2.75” • • • • • •
(76.2) (55.9) (19.0) (38.1) (75.4) (69.8)
2”-111/26 3.00” 2.20” .80” 1.92” 3.24” 3.00” • • • • • •
(76.2) (55.9) (20.3) (48.8) (82.4) (76.2)
2”-111/27 3.85” 2.70” .88” 1.94” 4.05” 3.75” • • • • • •
(97.8) (68.6) (22.4) (49.3) (102.9) (95.2)
21/2”-8 7 3.85” 2.70” 1.30” 2.32” 4.34” 4.02” • • • • • •
(97.8) (68.6) (33.0) (58.9) (110.2) (102.1)
21/2”-8 8 4.75” 2.70” 1.25” 2.38” 4.86” 4.50” • • • • • •
(120.6) (68.6) (31.7) (60.5) (123.4) (114.3)
3”-8 7 3.85” 2.70” 1.30” 2.54” 4.34” 4.02” • • • • • •
(97.8) (68.6) (33.0) (64.5) (110.2) (102.1)
3”-8 8 4.50” 2.70” 1.38” 3.00” 4.86” 4.50” • • • • • •
(114.3) (68.6) (35.1) (76.2) (123.4) (114.3)
*A/C— Across Corners; A/F—Across Flats
Dimensions shown are approximate and are subject to change without notice.
T-88 Dimensions in Inches (mm)
www.hubbell-wiring.com
A
(Overall)
B Ref.
C
D
F
E
Wire Management Products Technical Data
Cord Connectors
Technical Data
Dimensional Charts
Straight Hubbell Connectors
Zinc-Plated Steel Inches (mm) Stainless Steel Inches (mm)
FABCDEABCDE
Throat Throat
N.P.T. Form A/C* A/F* Ref. Dia. A/C* A/F* A/C* A/F* Dia. A/C* A/F*
1/4”- 18 1 • • • • • • • 1.01” .88” .90” .46” .38” .87” .75”
(25.7) (22.4) (22.9) (11.7) (9.7) (22.1) (19.0)
3/8”-18 1 .98” .88” .90” .42” .45” .99” .88” 1.01” .88” .90” .46” .45” .87” .75”
(24.9) (22.4) (22.9) (10.7) (11.4) (25.1) (22.4) (25.7) (22.4) (22.9) (11.7) (11.4) (22.1) (19.0)
1/2”-14 1 .98” .88” .90” .55” .45” 1.00” .88” • • • • • • •
(24.9) (22.4) (22.9) (14.0) (11.4) (25.4) (22.4)
1/2”-14 2 1.27” 1.13” 1.20” .55” .64” 1.10” 1.00” 1.30” 1.13” 1.10” .54” .63” 1.16” 1.00”
(32.3) (28.7) (30.5) (14.0) (16.3) (28.2) (25.4) (33.0) (28.7) (27.9) (13.7) (16.0) (29.5) (25.4)
1/2”-14 3 1.55” 1.38” 1.50” .55” .64” 1.40” 1.25” • • • • • • •
(39.4) (35.1) (38.1) (14.0) (16.3) (35.6) (31.7)
3/4”-14 2 1.27” 1.13” 1.20” .55” .64” 1.29” 1.13” • • • • • • •
(32.3) (28.7) (30.5) (14.0) (16.3) (32.8) (28.7)
3/4”-14 3 1.55” 1.38” 1.40” .55” .82” 1.40” 1.25” 1.59” 1.38” 1.30” .56” .81” 1.44” 1.25”
(39.4) (35.1) (35.6) (14.0) (20.8) (35.6) (31.7) (40.4) (35.1) (33.0) (14.2) (20.6) (36.6) (31.7)
1”-111/23 1.55” 1.38” 1.40” .70” .89” 1.54” 1.38” • • • • • • •
(39.4) (35.1) (35.6) (17.8) (22.6) (39.1) (35.1)
1”-111/24 1.92” 1.69” 1.60” .70” 1.02” 1.95” 1.69” 2.02” 1.75” 1.40” .70” 1.03” 1.88” 1.63”
(48.8) (42.9) (40.6) (17.8) (25.9) (49.5) (42.9) (51.3) (44.4) (35.6) (17.8) (26.2) (47.8) (41.4)
1”-111/25 2.40” 1.70” .70” 1.02” 2.46” 2.15” • • • • • • •
(61.0) (43.2) (17.8) (25.9) (62.5) (54.6)
11/4”-111/25 2.40” 1.70” .73” 1.27” 2.48” 2.19” • • • • • • •
(61.0) (43.2) (18.5) (32.3) (63.0) (55.6)
11/2”-111/25 2.40” 1.70” .74” 1.39” 2.48” 2.19” • • • • • • •
(61.0) (43.2) (18.8) (35.3) (63.0) (55.6)
11/2”-111/26 3.06” 2.20” .75” 1.52” 3.04” 2.83” • • • • • • •
(77.7) (55.9) (19.0) (38.6) (77.2) (71.9)
2”-111/26 3.06” 2.20” .78” 1.92” 3.32” 3.07” • • • • • • •
(77.7) (55.9) (19.8) (48.8) (84.3) (78.0)
2”-111/27 3.95” 2.70” .78” 1.99” 4.18” 3.89” • • • • • • •
(100.3) (68.6) (19.8) (50.5) (106.2) (98.8)
21/2”-8 7 • • • • • • • • • • • • • •
21/2”-8 • • • • • • • • • • • • • • •
3”-8 7 • • • • • • • • • • • • • •
3”-8 8 • • • • • • • • • • • • • •
*A/C— Across Corners; A/F—Across Flats
T-89
Dimensions in Inches (mm) www.hubbell-wiring.com
A
(Overall)
B Ref.
C
D
F
E
Technical Data Wire Management Products
Cord Connectors
Technical Data
Dimensional Charts
45° Hubbell Connectors
Aluminum Inches (mm) Zinc Plated Steel Inches (mm)
FABCDEGABCDEG
Throat Across Across Throat Across Across Across Across
N.P.T. Form Ref. Ref. Dia. Corners Flats Dia. Ref. Ref. Dia. Corners Flats Corners Flats
1/2”-14 2 2.00” 1.90” .55” .56” 1.27” 1.10” 1.13” 1.97” 1.90” .55” .57” 1.24” 1.06” 1.27” 1.13”
(50.8) (48.3) (14.0) (14.2) (32.3) (27.9) (28.6) (50.0) (48.3) (14.0) (14.4) (31.5) (26.9) (32.3) (28.6)
3/4”-14 3 2.30” 2.50” .56” .75” 1.48” 1.28” 1.38” • • • • • • • •
(58.4) (65.3) (14.2) (19.0) (37.6) (32.5) (34.9)
1”-111/24 2.60” 2.80” .70” 1.00” 1.69” 1.50” 1.75” • • • • • • • •
(66.0) (71.1) (17.8) (25.4) (42.9) (38.1) (44.4)
11/2”-111/25 3.90” 3.90” .74” 1.25” 2.45” 2.13” 2.31” • • • • • • • •
(99.1) (9.91) (18.8) (31.7) (62.2) (54.0) (58.7)
11/2”-111/25 3.90” 3.90” .74” 1.50” 2.45” 2.13” 2.31” • • • • • • • •
(99.1) (99.1) (18.8) (38.1) (62.2) (54.0) (58.7)
90° Hubbell Connectors
Aluminum Inches (mm) Zinc Plated Steel Inches (mm)
FABCDEGABCDEG
Throat Across Across Throat Across Across Across Across
N.P.T. Form Ref. Dia. Corners Flats Dia. Ref. Dia. Corners Flats Corners Flats
3/8”-18 1 1.27” 2.00” .46” .44” 1.15” 1.10” .88” • • • • • • • •
(32.3) (50.8) (11.7) (11.2) (29.2) (27.9) (22.2)
1/2”-14 2 1.56” 2.30” .50” .55” 1.30” 1.13” 1.13” 1.65” 2.38” .55” .55” 1.29” 1.13” 1.27” 1.13”
(39.6) (58.4) (12.7) (13.9) (33.0) (28.7) (28.6) (41.9) (60.5) (14.0) (13.8) (32.8) (28.7) (32.3) (28.6)
3/4”-14 3 1.79” 2.80” .56” .77” 1.49” 1.31” 1.38” 1.88” 2.90” .56” .77” 1.52” 1.33” 1.55” 1.38”
(45.5) (71.1) (14.2) (19.4) (37.8) (33.3) (34.9) (47.8) (73.7) (14.2) (19.4) (38.6) (33.8) (39.2) (34.9)
1”-111/24 2.08” 3.20” .70” 1.00” 1.70” 1.50” 1.75” 2.16” 3.20” .70” 1.00” 1.72” 1.50” 1.92” 1.69”
(52.8) (81.3) (17.8) (25.4) (43.2) (38.1) (44.4) (54.9) (81.3) (17.8) (25.4) (43.7) (38.1) (48.8) (42.8)
11/4”-111/25 3.18” 4.30” .73” 1.26” 2.47” 2.15” 2.31” • • • • • • • •
(80.8) (109.2) (18.5) (32.0) (62.7) (54.6) (58.7)
11/2”-111/25 3.18” 4.30” .75” 1.50” 2.47” 2.15” 2.31” • • • • • • • •
(80.8) (109.2) (19.2) (38.1) (62.7) (54.6) (58.7)
2”-111/26 3.51” 5.50” .80” 1.92” 2.98” 2.78” 3.00” • • • • • • • •
(89.2) (139.7) (20.3) (48.8) (75.7) (70.6) (76.2)
T-90 Dimensions in Inches (mm)
www.hubbell-wiring.com
B
Ref.
A
Ref.
D
C
E
F
G
B Ref.
A
D
D
E
F
G
90° Hubbell Connectors
Nylon Inches (mm)
FABCDEG
Throat Across Across
N.P.T. Form Ref. Dia. Corners Flats Dia.
3/8”-18 1 • • • • • • •
1/2”-14 2 1.41” 2.50” .55” .58” 1.23” 1.12” 1.32”
(35.8) (63.5) (14.0) (14.6) (31.2) (28.2) (33.4)
3/4”-14 3 1.65” 2.81” .56” .77” 1.42” 1.29” 1.56”
(41.9) (71.4) (14.2) (19.4) (36.1) (32.8) (39.6)
1”-111/24 1.99” 3.30” .70” 1.01” 1.82” 1.60” 1.88”
(50.5) (83.8) (17.8) (25.7) (46.2) (40.6) (47.6)
Dimensions shown are approximate and
are subject to change without notice.
Wire Management Products ?????
Cord Connectors
Technical Data
Dimensional Charts
H
U
B
B
E
L
L
®
D
F
E
E
.
C
.
C
.
BC
A
G
A
(Overall)
B Ref.
C
D
F
E
A
(Overall)
B Ref.
C (N.P.T. Thread Depth)
D
E
Female Hubbell Connectors
Aluminum Inches (mm)
F ABC D E
Throat Across Across
N.P.T. Form Dia. Ref. Dia. Corners Flats
3/8”-18 1 .88” 1.40” .56” .44” .94” .81”
(22.4) (35.6) (14.2) (11.2) (23.9) (20.6)
1/2”-14 2 1.13” 1.80” .56” .63” 1.15” 1.00”
(28.7) (45.7) (14.2) (16.0) (29.2) (25.4)
3/4”-14 2 1.13” 2.10” .75” .63” 1.44” 1.25”
(28.7) (53.3) (19.0) (16.0) (36.6) (31.7)
1”-111/24 1.75” 2.30” .88” 1.10” 1.88” 1.63”
(44.5) (58.4) (22.4) (27.9) (47.8) (41.4)
11/4”-111/25 2.31” 2.80” .95” 1.43” 2.64” 2.29”
(58.7) (71.1) (24.1) (36.3) (67.1) (58.2)
11/2”-111/25 2.31” 2.80” .95” 1.43” 2.64” 2.29”
(58.7) (71.1) (24.1) (36.3) (67.1) (58.2)
T-91
Dimensions in Inches (mm) www.hubbell-wiring.com
Dimensions in Inches (mm) www.hubbell-wiring.com
Wire Management Products Technical Data
Underground Feeder Connectors
Aluminum Inches (mm) Nylon Inches (mm) Zinc-Plated Steel Inches (mm)
FABCDEABCDEABCDE
Thrt. Thrt. Thrt.
N.P.T. Form Dia. Ref. Dia. A/C* A/F* Dia. Ref. Dia. A/C* A/F* A/C* A/F* Ref. Dia. A/C* A/F*
1/2”
-14
2 1.13” 1.10” .55” .64” 1.10” 1.00” 1.32” 1.50” .55” .58” 1.25” 1.13” 1.27” 1.13” 1.20” .55” .64” 1.11” 1.00”
(28.7) (27.9) (14.0) (16.3) (27.9) (25.4) (33.5) (38.1) (14.0)(14.7) (31.7) (28.7) (32.3) (28.7) (30.5) (14.0) (16.3) (28.2)(25.4)
3/4”-14 2 1.13” 1.10” .55” .64” 1.29” 1.13” • • • • • • 1.27” 1.13” 1.20” .55” .64” 1.29” 1.13”
(28.7) (27.9) (14.0) (16.3) (32.8) (25.4) (32.3) (28.7) (30.5) (14.0) (16.3) (32.8) (28.7)
3/4”-14 3 1.13” 1.50” .55” .82” 1.40” 1.25” 1.56” 1.60” .56” .77” 1.44” 1.31” 1.55” 1.38” 1.40” .56” .82” 1.40” 1.25”
(28.7) (38.1) (14.0) (20.8) (35.6) (31.7) (39.6) (40.6) (14.2)(19.6) (36.6) (33.3) (39.4) (35.1) (35.6) (14.2) (20.8) (35.6)(31.7)
*A/C - Across Corners; A/F - Across Flats
Low Profile Non-Metallic N.P.T. and PG Thread Connectors
Nylon Inches (mm)
N.P.T. A BCDEF
3/8” .984” .591” .591” .33” .827” .748”
(25) (15) (15) (8.38) (21) (19)
1/2” 1.378” .787” .591” .47” 1.063” .945”
(35) (20) (15) (12) (27) (24.23)
3/4” 1.417” .866” .591” .72” 1.417” 1.299”
(36) (22) (15) (18.3) (36) (33)
1” 1.654” .984” .984” 1.00” 1.850” 1.654”
(42) (25) (25) (25.4) (47) (42)
PG Thread A BCDEFG
PG7 .827” .472” .315” .26” .669” .591” .492”
(21) (12) (8) (6.6) (17) (15) (12.5)
PG9 .984” .591” .315” .33” .827” .748” .598”
(25) (15) (8) (8.38) (21) (19) (15.19)
PG11 1.181” .709” .315” .40” .984” .866” .732”
(30) (18) (8) (10.16) (25) (22) (18.6)
PG13.5 1.378” .787” .354” .47” 1.063” .945” .803”
(35) (20) (9) (12) (27) (24) (20.4)
PG16 1.378” .827” .394” .55” 1.181” 1.063” .886”
(35) (21) (10) (14) (30) (27) (22.5)
PG21 1.417” .866” .433” .72” 1.417” 1.299” 1.114”
(36) (22) (11) (18.3) (36) (33) (28.3)
PG29 1.653” .984” .433” 1.46” 1.85” 1.654” 1.457”
(42) (25) (11) (37) (47) (42) (37)
PG36 1.811” 1.181” .512” 1.85” 2.283” 2.087” 1.85”
(46) (30) (13) (47) (58) (53) (47)
Technical Data Wire Management Products
Cord Connectors
Selection Chart
2 Conductors
SVO,
SV,
Cord Type SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8
Approximate .25” .31” .33” .37” .38” .40” .54” .62” .68” .81”
Diameter (6.2) (7.8) (8.4) (9.3) (9.7) (10.2) (13.7) (15.6) (17.1) (20.6)
N.P.T. Form Catalog Numbers*
1/4”1 HC1004 HC1004 HC1005 HC1005 HC1006 HC1006 ••••
3/8”1 HC1010 HC1010 HC1011 HC1011 HC1012 HC1012 ••••
1/2”1 HC1016 HC1016 HC1017 HC1017 HC1018 HC1018 ••••
1/2”2 HC1022 HC1022 HC1022 HC1022 HC1023 HC1023 HC1024 HC1024 ••
1/2”3••••HC1025 HC1025 HC1026 HC1026 HC1027 HC1028
3/4”2 HC1032 HC1032 HC1032 HC1032 HC1033 HC1033 HC1034 HC1034 ••
3/4”3••••HC1035 HC1035 HC1036 HC1036 HC1037 HC1038
1” 4 • • • • HC1039 HC1039 HC1040 HC1040 HC1041 HC1042
1”5• •• •••• ••HC1045
11/4”5••••••• ••HC1050
11/2”5••••••• ••HC1055
11/2”6••••••• •••
2”6• •• •••• •••
2”7• •• •••• •••
21/2”7••••••• •••
3”7• •• •••• •••
Color Black Black White White Blue Blue Brown Brown Yellow Orchid
* Must add prefix, see Note 1; suffix, see Note 2, on page T-95.
3 Conductors
SVO,
SV,
Cord Type SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #18 #18 #16 #14 #18 #16 #14 #12 #10 #8
Approximate .26” .33” .35” .39” .39” .42” .57” .65” .71” .85”
Diameter (6.5) (8.3) (8.9) (9.8) (9.9) (10.7) (14.4) (16.4) (18.0) (21.5)
N.P.T. Form Catalog Numbers*
1/4”1 HC1004 HC1005 HC1005 HC1006 HC1006 HC1006 ••••
3/8”1 HC1010 HC1011 HC1011 HC1012 HC1012 HC1012 ••••
1/2”1 HC1016 HC1017 HC1017 HC1018 HC1018 HC1018 ••••
1/2”2 HC1022 HC1022 HC1022 HC1023 HC1023 HC1023 HC1024 •••
1/2”3 • • • HC1025 HC1025 HC1025 HC1026 HC1027 HC1027 HC1028
3/4”2 HC1032 HC1032 HC1032 HC1033 HC1033 HC1033 HC1034 •••
3/4”3 • • • HC1035 HC1035 HC1035 HC1036 HC1037 HC1037 HC1038
1” 4 • • • HC1039 HC1039 HC1039 HC1040 HC1041 HC1041 HC1042
1”5• •• •••• ••HC1045
11/4”5••••••• ••HC1050
11/2”5••••••• ••HC1055
11/2”6••••••• •••
2”6• •• •••• •••
2”7• •• •••• •••
21/2”7••••••• •••
3”7• •• •••• •••
Color Black White White Blue Blue Blue Brown Yellow Yellow Orchid
* Must add prefix, see Note 1; suffix, see Note 2, on page T-95.
T-92 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Cord Connectors
Selection Chart
2 Conductors
SVO,
SV,
CordType SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250
Approx. .94” 1.08” 1.17” 1.27” 1.44” 1.52” 1.65” 1.77” 1.92” 2.16”
Diameter (23.8) (27.4) (29.7) (33.3) (36.6) (38.6) (41.9) (45.0) (48.8) (51.9)
N.P.T. Form Catalog Numbers*
1/4”1••••••• •••
3/8”1••••••• •••
1/2”1••••••• •••
1/2”2••••••• •••
1/2”3••••••• •••
3/4”2••••••• •••
3/4”3••••••• •••
1” 4 HC1043 HC1044 • •••• •••
1” 5 HC1046 HC1047 HC1048 HC1049 ••• •••
11/4”5 HC1051 HC1052 HC1053 HC1054 ••• •••
11/2”5 HC1056 HC1057 HC1058 HC1059 ••• •••
11/2”6 • • • HC1060 HC1061 HC1062 HC1063 HC1064 ••
2” 6 • • • HC1065 HC1066 HC1067 HC1068 HC1069 ••
2”7• •• •••• HC1070 HC1071 HC1073
21/2”7••••••• HC1076 HC1077 HC1079
3”7• •• •••• HC1086 HC1087 HC1089
Color Gray‡ Pink‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
* Must add prefix, see Note 1; suffix, see Note 2, on page T-95.
‡ F5 and larger will not be color coded.
3 Conductors
SVO,
SV,
CordType SVT SJ, SJO, SJT, SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250
Approx. 1.00” 1.17” 1.24” 1.34” 1.51” 1.65” 1.75” 1.80” 2.07” 2.39”
Diameter (25.4) (29.7) (31.5) (34.0) (38.4) (41.9) (44.5) (48.0) (52.6) (60.7)
N.P.T. Form Catalog Numbers*
1/4”1••••••• •••
3/8”1••••••• •••
1/2”1••••••• •••
1/2”2••••••• •••
1/2”3••••••• •••
3/4”2••••••• •••
3/4”3••••••• •••
1” 4 HC1044 •• •••• •••
1” 5 HC1047 HC1048 HC1048 HC1049 ••• •••
11/4”5 HC1052 HC1053 HC1053 HC1054 ••• •••
11/2”5 HC1057 HC1058 HC1058 HC1059 ••• •••
11/2”6 • • • HC1060 HC1062 HC1063 HC1064 •••
2” 6 • • • HC1065 HC1067 HC1068 HC1069 •••
2” 7 • • • • • • HC1070 HC1071 HC1073 HC1075
21/2”7••••••HC1076 HC1077 HC1079 HC1081
3” 7 • • • • • • HC1086 HC1087 HC1089 HC1091
Color Gray‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
* Must add prefix, see Note 1; suffix, see Note 2, on page T-95.
‡ F5 and larger will not be color coded.
T-93
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Cord Connectors
Selection Chart
4 Conductors
SJ, SJO,
SJT,
Cord Type SJTO S, SO, ST, STO
Cord Size #18 #16 #14 #18 #16 #14 #12 #10 #8
Approx. .36” .39” .43” .42” .45” .61” .70” .77” .97”
Diameter (9.0) (9.8) (10.8) (10.7) (11.4) (15.5) (17.8) (19.4) (24.6)
N.P.T. Form Catalog Numbers*
1/4”1 HC1005 HC1006 HC1006 HC1006 ••• ••
3/8”1 HC1011 HC1012 HC1012 HC1012 ••• ••
1/2”1 HC1017 HC1018 HC1018 HC1018 ••• ••
1/2”2 HC1022 HC1023 HC1023 HC1023 HC1023 HC1024 •••
1/2”3 • HC1025 HC1025 HC1025 HC1025 HC1026 HC1027 HC1028 •
3/4”2 • HC1033 HC1033 HC1033 HC1033 HC1034 •••
3/4”3 • HC1035 HC1035 HC1035 HC1035 HC1036 HC1037 HC1038 •
1” 4 • HC1039 HC1039 HC1039 HC1039 HC1040 HC1041 HC1042 HC1043
1”5• •• •••• •HC1046
11/4”5••••••• •HC1051
11/2”5••••••• •HC1056
11/2”6••••••• ••
2”6• •• •••• ••
2”7• •• •••• ••
21/2”7••••••• ••
3”7• •• •••• ••
Color White Blue Blue Blue Blue Brown Yellow Orchid Gray‡
* Must add prefix, see Note 1; suffix, see Note 2, on page T-95.
‡ F5 and larger will not be color coded.
5 Conductors
Cord Type S, SO, ST, STO
Cord Size #18 #16 #14 #12 #10 #8 #6
Approx. .50” .54” .70” .76” .83” 1.06” 1.18”
Diameter (12.7) (13.7) (17.7) (19.3) (21.1) (26.9) (30.0)
N.P.T. Form Catalog Numbers*
1/2”2HC1023 HC1024 •••••
1/2”3HC1025 HC1026 HC1027 HC1028 HC1028 ••
3/4”2HC1033 HC1034 •••••
3/4”3HC1035 HC1036 HC1037 HC1038 HC1038 ••
1” 4 HC1039 HC1040 HC1041 HC1042 HC1042 HC1044 •
1” 5 • • • HC1045 HC1045 HC1047 HC1048
11/4”5 • • • HC1050 HC1050 HC1052 HC1053
11/2”5 • • • HC1055 HC1055 HC1057 HC1058
Color Blue Brown Yellow Orchid‡ Orchid‡ Pink ‡
* Must add prefix, see Note 1; suffix, see Note 2, on page T-95.
‡ F5 and larger will not be color coded.
T-94 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Cord Connectors
Selection Chart
4 Conductors
SJ, SJO,
SJT,
Cord Type SJTO S, SO, ST, STO
Cord Size #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0
Approx. .94” 1.08” 1.17” 1.27” 1.44” 1.52” 1.65” 1.77” 1.92”
Diameter (23.8) (27.4) (29.7) (33.3) (36.6) (38.6) (41.9) (45.0) (48.8)
N.P.T. Form Catalog Numbers*
1/4”1 • • • • • • • • •
3/8”1 • • • • • • • • •
1/2”1 • • • • • • • • •
1/2”2 • • • • • • • • •
1/2”3 • • • • • • • • •
3/4”2 • • • • • • • • •
3/4”3 • • • • • • • • •
1” 4 HC1044 ••••• •••
1” 5 HC1047 HC1049 HC1049 •• • • • •
11/4”5 HC1052 HC1054 HC1054 •• • • • •
11/2”5 HC1057 HC1059 HC1059 •• • • • •
11/2”6 • HC1060 HC1060 HC1061 HC1063 HC1064 •••
2” 6 • HC1064 HC1065 HC1066 HC1068 HC1069 •••
2” 7 • • • • • HC1070 HC1071 HC1073 HC1074
21/2”7 • • • • • HC1076 HC1077 HC1079 HC1080
3” 7 • • • • • HC1086 HC1087 HC1089 HC1090
Color Pink‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡
* Must add prefix, see Note 1; suffix, see Note 2, below.
‡ F5 and larger will not be color coded.
T-95
Dimensions in Inches (mm) www.hubbell-wiring.com
Notes
1. Add the proper prefix to the HC number to
identify the type of connector desired:
SHC = Straight Hubbell Connector
NHC = 90° Hubbell Connector
FHC = Female Hubbell Connector
VHC = 45° Hubbell Connector
2. Add the proper suffix to identify material desired:
Aluminum = No suffix
Zinc-Plated Steel = ZP
Corrosion Resistant Nylon = CR
Stainless Steel = SS
3. This chart is a general guide to assist in the
selection of Hubbell Cord Connectors for various
cord sizes. The Hubbell Cord Connector catalog
numbers selected, have been inserted into
spaces which in our judgment represent the best
cord connector which will fit the listed cord size.
The diameters of the cords are approximate and
may vary depending on the manufacturer. It is
suggested that the appropriate cord
manufacturer’s dimension chart be consulted for
exact dimensions.
4. *Cable jacket may have to be stripped to allow
conductors to pass through connector body.
Technical Data Wire Management Products
Locknuts and Sealing O-Rings
Technical Data
T-96 Dimensions in Inches (mm)
www.hubbell-wiring.com
Dimensions shown are approximate and
are subject to change without notice.
A
C
B
A
Thread Size
(N.P.S.)
B
Minimum
THK.
C
Maximum
Diameter
Locknuts – Sizes 1/2” - 3”
Carbon Steel with Commercial Bright Zinc Plate
AB C
Trade Thd. Size Min. Thk. Max. Dia. Catalog
Size inch inch (mm) inch (mm) Numbers
1/2”1/2”-14 .09” (2.3) 1.14” (29.0) 00322001
3/4”3/4”-14 .11” (2.8) 1.43” (36.3) 00322002
1” 1”-111/2.13” (3.3) 1.77” (45.0) 00322003
11/4”1
1/4”-111/2.13” (3.3) 2.28” (57.9) 00322004
11/2”1
1/2”-111/2.13” (3.3) 2.60” (66.0) 00322005
2” 2”-111/2.13” (3.3) 3.18” (80.8) 00322006
21/2”2
1/2”-8 .18” (4.6) 3.56” (90.4) 00322007
3” 3”-8 .36” (9.1) 4.13” (104.9) 00322082
Metal Clad Sealing O-Rings – Sizes 1/2” - 4”
Zinc-Plated Steel with Neoprene Ring
N.P.T. A B C
Hub Inside Dia. Outside Dia. Thk. Catalog
Size inch (mm) inch (mm) inch (mm) Numbers
1/2” .80” (20.3) 1.08” (27.4) .16” (3.2) 20509001
3/4” 1.00” (25.4) 1.34” (34.0) .16” (3.2) 20509002
1” 1.25” (31.6) 1.63” (41.4) .16” (3.2) 20509003
11/4” 1.61” (40.9) 2.00” (50.8) .16” (3.2) 20509004
11/2” 1.84” (46.7) 2.36” (59.9) .16” (3.2) 20509005
2” 2.31” (58.7) 2.83” (71.9) .16” (3.2) 20509006
Chrome Plated Steel with Neoprene Ring
21/2” 2.91” (73.9) 3.44” (87.4) .24” (6.1) 20509007
3” 3.52” (89.4) 4.08” (103.6) .24” (6.1) 20509008
4” 4.54” (115.3) 5.30” (134.6) .29” (7.4) 20509009
Nylon PG Thread Locknuts
PG Thread A B C D Catalog
Size inch (mm) inch (mm) inch (mm) inch (mm) Numbers
PG7 .784” (20) .828” (21) .492 (12.5) .197” (5) LNPG7B
PG9 .866” (22) .945” (24) .598 (15.2) .197” (5) LNPG9B
PG11 .945” (24) 1.024” (26) .732 (18.5) .197” (5) LNPG11B
PG13.5 1.06” (27) 1.142” (29) .803 (20.4) .236” (6) LNPG13B
PG16 1.18” (30) 1.299” (33) .886 (22.5) .236” (6) LNPG16B
PG21 1.417” (36) 1.535” (39) 1.114 (28.3) .276” (7) LNPG21B
PG29 1.811” (46) 1.969” (50) 1.457 (37) .276” (7) LNPG29B
PG36 2.362” (60) 2.598” (66) 1.850 (47) .317” (8.05) LNPG36B
Wire Management Products Technical Data
HUBBELL JUNIORS®Miniature Nylon Cord Connectors
Technical Data
Hubbell Juniors
Operating Temperature Range
Nylon (connectors and GOTCHA®rings) -40°F to +225°F (-40°C to +107°C)
Neoprene (bushings) -30°F to +240°F (-34°C to +115°C)
Due to the limiting factors of nylon and neoprene, any complete liquidtight Hubbell Junior will continuously perform in the range
of -30°F to +225°F (-34°C to +107°C).
Snap-In continuously performs -40°F to +225°F (-40°C to +107°C).
Flammability
Hubbell Juniors have a UL 94V-2 rating.
Certifications
Product Agency
Liquidtight and Liquidtight with Spiral UL Listed
CSA Certified
Snap-In UL Recognized
CSA Certified
Knockout Holes
Knockout Hole
Recommended
N.P.T. Min. to Max.
Hub Size inches (mm)
1/4” .54”-.57” (13.7-14.5)
3/8” .67”-.70” (17.0-17.8)
1/2” .86”-.91” (21.8-23.1)
Dimensions shown are subject to change without notice.
T-97
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
HUBBELL JUNIORS®Miniature Nylon Cord Connectors
Technical Data
T-98 Dimensions in Inches (mm)
www.hubbell-wiring.com
B
F
G
DE
AC
B
E
F
C
D
A
G
F
C
B
AChassis
Thicknes
s
Max
E
Snap-In
For
Chas. Required Dimensional
Dia. Thk. Hole Size Specifications
Range (Max.) A B C D E F G
Inches Inches Inches Inches Inches Inches Inches Inches Inches
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
.22”-.27” .10” .50” .45” .28” .28” .54” .12” 1.84”
(5.6-6.9) (2.5) (12.7) (11.4) (7.1) (7.1) (13.7) (3.0) (44.2)
.28”-32” .10” .50” .47” .28” .33” .59” .12” 1.84”
(7.1-8.1) (2.5) (12.7) (11.9) (7.1) (8.4) (15.0) (3.0) (44.2)
.30”-.36” .13” .63” .55” .36” .37” .65” .14” 2.18”
(7.6-9.1) (3.3) (16.0) (14.0) (9.1) (9.4) (16.5) (3.6) (55.4)
.32”-.43” .13” .75” .66” .45” .44” .75” .14” 2.60”
(8.1-10.9) (3.3) (19.0) (16.8) (11.4) (11.2) (19.1) (3.6) (66.0)
Liquidtight
FABCD E
Across Across
Dia. Ref. Throat Dia. Corners Flats
Inches Inches Inches Inches Inches Inches
N.P.T. (mm) (mm) (mm) (mm) (mm) (mm)
1/4”-18 .65” 1.30” .40” .29” .65” .60”
(16.5) (33.0) (10.2) (7.4) (16.5) (15.2)
3/8”-18 .81” 1.44” .41” .36” .81” .75”
(20.6) (36.6) (10.4) (9.1) (20.6) (19.1)
1/2”-14 1.00” 1.56” .46” .45” .99” .92”
(25.4) (39.6) (11.7) (11.4) (25.1) (23.4)
Liquidtight with Spiral
G ABCE E F
Throat Across Across
Dia. Ref. Dia. Corners Flats
Inches Inches Inches Inches Inches Inches Inches
N.P.T. (mm) (mm) (mm) (mm) (mm) (mm) (mm)
1/4”-18 .65” 2.55” .40” .29” .27” .65” .60”
(16.5) (64.8) (10.2) (7.4) (6.9) (16.5) (15.2)
3/8”-18 .81” 3.10” .41” .36” .35” .81” .75”
(20.6) (78.7) (10.4) (9.1) (8.9) (20.6) (19.1)
1/2”-14 1.00” 3.72” .46” .45” .45” .99” .92”
(25.4) (94.5) (11.7) (11.4) (11.4) (25.1) (23.4)
Wire Management Products Flexible Non-metallic Conduit Grips
Strain Relief
Flexible Non-Metallic Conduit Grips
Steel Fitting, Stainless Steel Mesh, Liquidtight, for UL Type A Conduit
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-106
through T-107.
Straight Male Hubbell Fitting
Conduit Trade Trade Size Mesh Length Catalog
Size (Inches) N.P.T. (Inches) Inches (cm) Numbers
3/8”1/2”3
3/4” (9.52) H038CNK
1/2”1/2”4
1/2” (11.43) H050CNK
3/4”3/4”6
1/4” (15.87) H075CNK
1” 1” 71/2” (19.05) H100CNK
11/4”1
1/4” 9” (22.86) H125CNK
11/2”1
1/2”13
1/2” (34.29) H150CNK
2” 2” 141/2” (36.83) H200CNK
90° Male Hubbell Fitting
Conduit Trade Trade Size Mesh Length Catalog
Size (Inches) N.P.T. (Inches) Inches (cm) Numbers
3/8”1/2”3
3/4” (9.52) H0389CNK
1/2”1/2”4
1/2” (11.43) H0509CNK
3/4”3/4”6
1/4” (15.87) H0759CNK
1” 1” 71/2” (19.05) H1009CNK
11/4”1
1/4” 9” (22.86) H1259CNK
11/2”1
1/2”13
1/2” (34.29) H1509CNK
2” 2” 141/2” (36.83) H2009CNK
T-99
Dimensions in Inches (mm) www.hubbell-wiring.com
S
traight Male with Fitting
9
0° Angle
Flexible Non-metallic Conduit Grips Wire Management Products
Strain Relief
Flexible Metallic Conduit Grips
Steel Fitting, Stainless Steel Mesh, Liquidtight, for Liquidtight Flexible Metal Conduit
T-100 Dimensions in Inches (mm)
www.hubbell-wiring.com
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-103
through T-105.
9
0° Angle with Male Fitting
S
traight with Male Fitting
Benefits
• Prevents conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
Straight With Male Fitting
Conduit Catalog Catalog
Trade Size Trade Size Mesh Length Numbers Numbers
(Inches) N.P.T. (Inches) Inches (cm) (Insulated) (Non-insulated)
3/8”1/2” 3” (7.62) 074093511 074093401
1/2”1/2”3
1/2” (8.89) 074093512 074093402
3/4”3/4” 4” (10.16) 074093513 074093403
1” 1” 5” (12.70) 074093514 074093404
11/4”1
1/4” 6” (15.24) 074093515 074093405
11/2”1
1/2”6
3/4” (17.14) 074093516 074093406
2” 2” 8” (20.32) 074093518 074093408
21/2”2
1/2”9
3/4” (24.76) 074093520 074093410
3” 3” 11” (27.94) 074093522 074093412
4” 4” 14” (35.56) 074093526 •
90° Angle With Male Fitting
Conduit Catalog Catalog
Trade Size Trade Size Mesh Length Numbers Numbers
(Inches) N.P.T. (Inches) Inches (cm) (Insulated) (Non-insulated)
3/8”1/2” 3” (7.62) 074093541 074093421
1/2”1/2”3
1/2” (8.89) 074093542 074093422
3/4”3/4” 4” (10.16) 074093543 074093423
1” 1” 5” (12.70) 074093544 074093424
11/4”1
1/4” 6” (15.24) 074093545 074093425
11/2”1
1/2”6
3/4” (17.14) 074093546 074093426
2” 2” 8” (20.32) 074093548 074093428
21/2”2
1/2”9
3/4” (24.76) 074093550 •
3” 3” 11” (35.56) 074093552 •
Wire Management Products Flexible Non-metallic Conduit Grips
Strain Relief
Flexible Metallic Conduit Grips
Steel Fitting, Stainless Steel Mesh, Liquidtight, for Flexible Metal Liquidtight Conduit
Read This Data
It is important that you read all
breaking strength, safety and
technical data relating to this
product on pages T-103 through
T-105.
S
traight with Chase Connector
4
5° Angle with Male Fitting
45° Angle With Male Fitting
Conduit Catalog Catalog
Trade Size Trade Size Mesh Length Numbers Numbers
(Inches) N.P.T. (Inches) Inches (cm) (Insulated) (Non-insulated)
3/8”1/2” 3” (7.62) 074093561 074093441
1/2”1/2”3
1/2” (8.89) 074093562 074093442
3/4”3/4” 4” (10.16) 074093563 074093443
1” 1” 5” (12.70) 074093564 074093444
11/4”1
1/4” 6” (15.24) 074093565 074093445
11/2”1
1/2”6
3/4” (17.14) 074093566 074093446
2” 2” 8” (20.32) 074093568 074093448
Note: Refer to page T-89 for fitting dimensions.
Straight With Chase Fitting
Conduit
Trade Size Trade Size Mesh Length Catalog
(Inches) N.P.T. (Inches) Inches (cm) Numbers
1/2”1/2”3
1/2” (8.89) 07406079
3/4”3/4” 4” (10.16) 07406080
1” 1” 5” (12.70) 07406081
11/4”1
1/4” 6” (15.24) 07406082
11/2”1
1/2”6
3/4” (17.14) 07406083
T-101
Dimensions in Inches (mm) www.hubbell-wiring.com
Hose Containment Grips Wire Management Products
Strain Relief
Hose Containment Grips
Custom Designed Grips, for High Pressure Hose Restraint
Read This Data
It is important that you read all breaking strength,
safety and technical data relating to this product
on pages T-68 through T-69.
Types of Attachment
The five attachment methods shown below
provide unlimited flexibility of attachment to meet
any condition.
Type E
Double Eye Grip, used where fastening is made with eyebolts
or similar anchor terminations.
Type A
Single Eye Grip, used where fastening MUST be made from
one point.
Type U
Universal Bale Grip, used to fasten around a structure or
closed eye.
Type Y
Threaded bolt (5/16-18 x 1 1/2” long), used to fasten through
drilled holes in plate.
Type F
Split fitting to fit AN-818 nuts. Fitting is positioned over nut and
located with internal flange. A hose clamp is furnished and
required to hold the fitting in correct position.
T-102 Dimensions in Inches (mm)
www.hubbell-wiring.com
Note: It should be emphasized that Kellems®Hose Containment Grips are not to be used as a pressure reinforcing device for hose
systems. These grips are custom made. To order Consult factory for details.
Kellems Hose Containment Grips are used on high pressure, flexible hose lines to prevent the hose from
whipping violently in the event of hose failure at the fitting. These grips will prevent serious injury to
personnel and damage to equipment by holding the hose in place in the event of hose failure.
Kellems patented Hose Containment Grips are made of stainless steel with double weave mesh
construction for high strength and come complete with hose clamps.
Kellems Hose Containment Grips are supplied in diameters, length and attachments to meet individual
requirements. Contact the Wiring Device-Kellems factory for specific information. These grips help meet
OSHA Federal Register 1926-302 (b), 1926-603 (9), (10), JIC H-1-1973 (H13.11) and JIC P-1-1975
(P11.34) requirements.
Wire Management Products Technical Data
Kellems®Grips for Strain Relief
Technical Section
Conduit Grips for Liquidtight Flexible Metal Conduit
Kellems Liquidtight, Flexible Metal Conduit Grips are offered with high quality
Hubbell plated steel fittings in a wide variety of N.P.T. sizes and configurations,
either insulated or non-insulated. The addition of a stainless steel mesh to these
fittings makes them stronger than the conduit itself. Kellems Conduit Grips
prevent conduit pull-out from the connecting fitting that is subject to stress, pull
tension, vibration, motion or strain. They promote safe electrical systems and
reduce equipment downtime.
Benefits
• Prevents conduit pull-out and damage at the fitting.
• Reduces equipment downtime.
• Liquidtight fittings.
• Easily installed.
• Stainless steel grip resists corrosion.
Kellems Conduit Grips are suitable for use in hazardous locations per Class I
Div. 2, Class II Div. 1 & 2, Class III Div. 1 & 2 of the National Electric Code
sections 501-4(b), 502-4(a), 502-4(b), 503-3(a) and 503-3(b).
Application
Kellems Conduit Grips are used in the wiring of machine tools, motors,
molding equipment, transformers, weaving and paper machines, fans,
lighting, bakeries, breweries, food processing, chemical plants, dairies, mines
and any application that requires Liquidtight Conduit.
Safety And Working Load Factors For Wire Mesh Grips
T-103
Dimensions in Inches (mm) www.hubbell-wiring.com
The broad application of Kellems grips on a wide
variety of objects requires that adequate safety
factors be used to establish working loads. The
approximate breaking strength of a Kellems grip
represents an average calculation based on data
established from actual direct tension testing done
in our engineering laboratories.
It is impossible to catalog or guarantee a safety
factor suitable for all applications as operating
conditions are never the same. The tension,
diameter, movement, number of objects gripped,
gripping surface, and the attachments used are just
some of the factors which vary with each
application. These factors, together with the effects
of abrasion, corrosion, prior use or abuse and any
other variables of a specific application, must be
considered by the user and the grip replaced as
appropriate. Where the conditions of the
application are not well defined or known or where
risk of injury to persons or property is involved, a
greater safety factor should be utilized. Should our
opinion be needed, call the factory.
Under normal conditions, Kellems’
recommended factor of safety is five for catalog
listed pulling grips, and ten for catalog listed
support grips. The factory should be consulted
for specific application recommendations
where strength and holding power are
important factors.
Any warranty as to quality, performance or fitness
for use of grips is always premised on the condition
that the published breaking strengths apply only to
new, unused grips, and that such products are
properly stored, handled, used, maintained and
inspected by the user at a frequency appropriate
for the use and condition of the grip.
For grip applications on materials other than those
that the grips have been specifically designed for,
consult the factory.
Examples
Approx. Breaking Strength Max. Rec. Load
Grip Style Lbs. (N) Safety Factor Lbs. (N) Catalog Numbers
Bus Drop 1,000 (4,448) 10 100 (448) 074093402
The maximum recommended working load then is the
tension to be exerted on the grip in application with a
margin of safety to take care of unforeseen and unusual
circumstances.
It is the end-user’s decision to determine how much of a
safety factor is acceptable to him.
Technical Data Wire Management Products
Kellems®Grips for Strain Relief
Technical Section
Conduit Grips for Liquidtight Flexible Metal Conduit
Hardened Steel Locknut
has tangs that dig into
box for excellent conti-
nuity of ground. Locknut
will not slip or spin.
Connectors with insulated throats
protect insulation on wires during
wire pulling. Yellow color easily
seen by inspectors. 2 " - 4" sizes
include insulating bushing instead
of fixed insulator. Steel grounding ferrule easily
threaded by hand. Fits convolutions
to conduit. Eliminates pullouts and
insures continuty of ground.
Distortion free to remain reusable.
Nylon gland ring is split for ease of
installation and greater compres-
sion. Reversible design cannot be
installed facing the wrong way.
Nylon is impervious to liquids,
unaffected by temperature
extremes and resists abrasion.
Hexagonal compression nut is
screw machined steel through
1" and malleable iron on larger
sizes.
Optional Sealing Washer gives
better liquidtight protection around
knockout of sheet metal box. Neo-
prene gasket seals out liquids and
steel retaining ring protects gasket
from distortion. Order separately.
Body is virutally unbreakable. Straight
connectors through 1" are screw
machine steel; other sizes malleable
iron. Threads at left are tapered to
insure liquidtight seal in threaded hub.
Liquidtight conduit cutaway view shows
flexible steel core under plastic jacket.
Wire mesh grip
prevents pullout.
Liquidtight conduit cutaway
view shows flexible steel core
under plastic jacket.
1
2
T-104 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Kellems®Grips for Strain Relief
Technical Section
Liquidtight Flexible Metal Conduit Grip Fitting Dimensions-Inches
Straight
with Male Fitting
Dimensions
D
Trade A B CThroat ECatalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Numbers
3/8” 1.43” .59” 1.20” 1.06” .61” 1.07” .93” 074093401
1/2” 1.43” .59” 1.34” 1.19” .61” 1.22” 1.06” 074093402
3/4” 1.56” .59” 1.55” 1.37” .84” 1.43” 1.25” 074093403
1” 1.68” .66” 1.95” 1.69” 1.06” 1.73” 1.56” 074093404
11/4” 2.03” .63” 2.39” 2.06” 1.37” 2.36” 2.08” 074093405
11/2” 2.21” .63” 2.72” 2.38” 1.53” 2.79” 2.48” 074093406
2” 2.28” .69” 3.08” 2.87” 2.06” 3.32” 2.90” 074093408
Straight
with Male Fitting
with Insulated Throat
Dimensions
D
Trade A B CThroat ECatalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Numbers
3/8” 1.50” .66” 1.20” 1.06” .57” 1.07” .93” 074093511
1/2” 1.50” .66” 1.34” 1.19” .57” 1.22” 1.06” 074093512
3/4” 1.62” .66” 1.55” 1.38” .78” 1.43” 1.25” 074093513
1” 1.75” .72” 1.95” 1.69” .98” 1.73” 1.56” 074093514
11/4” 2.09” .69” 2.39” 2.06” 1.29” 2.36” 2.08” 074093515
11/2” 2.28” .69” 2.72” 2.37” 1.53” 2.79” 2.48” 074093516
2” 2.34” .75” 3.08” 2.87” 1.95” 3.32” 2.90” 074093518
21/2” 3.56” 1.06” 3.92” 3.62” 2.42” 3.85” 3.60” 074093520
3” 3.81” 1.06” 4.70” 4.31” 3.01” 4.65” 4.33” 074093522
4” 3.81” 1.06” 5.75” 5.31” 3.96” 5.75” 5.39” 074093526
45° Angle with Male Fitting
Dimensions
M
Trade H J K LThroat NCatalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Numbers
3/8”1.19” 1.28” .59” 1.20” 1.06” .60” 1.16” 1.02” 074093441
1/2” 1.19” 1.28” .59” 1.34” 1.19” .61” 1.21” 1.06” 074093442
3/4” 1.19” 1.43” .59” 1.55” 1.45” .84” 1.50” 1.32” 074093443
1” 1.38” 1.53” .66” 1.95” 1.69” 1.05” 1.82” 1.59” 074093444
11/4” 1.42” 1.69” .63” 2.39” 2.06” 1.37” 2.32” 2.03” 074093445
11/2” 1.66” 2.00” .66” 2.72” 2.38” 1.60” 2.62” 2.29” 074093446
2” 1.69” 2.25” .66” 3.08” 2.88” 2.05” 3.21” 2.80” 074093448
45°
Angle with Male Fitting with Insulated Throat
Dimensions
M
Trade H J K LThroat NCatalog
Size Ref. A/C* A/F* Dia. A/C* A/F* Numbers
3/8” 1.25” 1.28” .66” 1.20”1.06” .57” 1.16” 1.02” 074093561
1/2” 1.25” 1.28” .66” 1.34” 1.19” .57” 1.21” 1.06” 074093562
3/4” 1.25” 1.44” .66” 1.55” 1.45” .78” 1.50” 1.32” 074093563
1” 1.44” 1.53” .72” 1.95” 1.69” .98” 1.82” 1.59” 074093564
11/4” 1.48” 1.69” .69” 2.39” 2.06” 1.29” 2.32” 2.03” 074093565
11/2” 1.72” 2.00” .72” 2.72” 2.38” 1.53” 2.62” 2.29” 074093566
2” 1.75” 2.25” .72” 3.08” 2.87” 1.95” 3.21” 2.80” 074093568
90° Angle with Male Fitting
Dimensions
O
Trade D E FG Throat PCatalog
Size A/C* A/F* Ref. Dia. A/C* A/F* Numbers
3/8” 1.31” .59” 1.20” 1.06” 1.44” .60” 1.13” .99” 074093421
1/2” 1.31” .59” 1.34” 1.12” 1.44” .61” 1.21” 1.00” 074093422
3/4” 1.44” .59” 1.55” 1.45” 1.63” .83” 1.48” 1.29” 074093423
1” 1.78” .66” 1.95” 1.60” 2.19” 1.05” 1.80” 1.57” 074093424
11/4” 1.97” .63” 2.39” 2.06” 2.50” 1.37” 2.32” 2.02” 074093425
11/2” 2.19” .66” 2.72” 2.38” 2.69” 1.61” 2.58” 2.25” 074093426
2” 2.53” .66” 3.08” 2.87” 3.25” 2.05” 3.14” 2.75” 074093428
90°
Angle with Male Fitting with Insulated Throat
Dimensions
O
Trade D E FG Throat PCatalog
Size A/C* A/F* Ref. Dia. A/C* A/F* Numbers
3/8” 1.38” .66” 1.20” 1.06” 1.44” .60” 1.13” .99” 074093541
1/2” 1.38” .66” 1.34” 1.12” 1.44” .57” 1.21” 1.00” 074093542
3/4” 1.50” .66” 1.55” 1.45” 1.63” .78” 1.48” 1.29” 074093543
1” 1.84” .66” 1.95” 1.60” 2.19” .98” 1.80” 1.57” 074093544
11/4” 2.03” .69” 2.39” 2.06” 2.50” 1.29” 2.32” 2.02” 074093545
11/2” 2.25” .69” 2.72” 2.38” 2.69” 1.53” 2.58” 2.20” 074093546
2” 2.59” .72” 3.08” 2.87” 3.25” 1.95” 3.14” 2.75” 074093548
21/2” 3.44” 1.00” 3.92” 3.63” 4.25” 2.42” 3.78” 3.50” 074093550
3” 3.75” 1.00” 4.70” 4.31” 4.87” 3.01” 4.64” 4.30” 074093552
G
O
Throat
Dia.
E
D
F P
A/C A/F
J
M
Throat
Dia.
L
K
H
N
A/C A/F
M
Throat
Dia.
E
A/C A/F
C
A
Ref.
B
Ref.
T-105
Dimensions in Inches (mm) www.hubbell-wiring.com
Dimensions shown are approximate and are subject to change without notice.
Technical Data Wire Management Products
Kellems®Grips for Strain Relief
Technical Section
T-106 Dimensions in Inches (mm)
www.hubbell-wiring.com
Conduit Grips for (UL Type A) Non-metallic,
Flexible, Liquidtight Conduit
Kellems Grips for UL Type A, non-metallic, flexible, liquidtight conduit
are available in straight and 90° male and feature a high quality
Hubbell plated steel or malleable iron fitting, complete with a sealing
O-ring, lock nut and stainless steel mesh. These grips increase the
retention of the conduit in the fitting, control its arc-of-bend and
provide a liquidtight seal.
Application
These grips are used on UL Type A non-metallic conduit connections
at limit switches, motor boxes, panel boards, control stations and on
all types of machinery and machine tools.
Benefits
• Provides a liquidtight seal.
• Helps prevent conduit pull-out.
• Reduces conduit cutting, kinking, fraying and splitting at the fitting.
• Easily installed.
S
teel Locknut has tangs that dig
i
nto box for excellent continuity of
g
round. Locknut will not slip or spin.
Neoprene "O"-ring is factory
assembled into the body to seal out
liquids.
Body is virtually unbreakable. Straight connectors
through 1" are screw machine steel; other sizes are
malleable iron. Threads are tapered to insure liquidtight
seal when used in threaded hub. Octagonal shape
inside holds the ferrule to prevent conduit from twisting
during installation.
Wire mesh grip
prevents pullout.
Hexagonal compression nut is machine
steel through 1" malleable iron on larger
sizes. Tapered interior compresses
sleeve over conduit sealing out liquids
and preventing pullout.
Yellow nylon sleeve installs over
conduit. Six slits in sleeve permit
tight compression onto conduit as
compression nut is tightened.
Yellow nylon ferrule fits inside non-
metallic conduit to hold the shape.
Barb in designed to assure liquidtight
seal even with non-square cut.
Ferrule is keyed to fit into body to
prevent conduit twisting.
I
nsulated throat protects insulation
o
n wires during pulling. Yellow color
e
asily seen by inspectors.
Wire Management Products Technical Data
Kellems®Grips for Strain Relief
Technical Section
Dimensional Charts For (UL Type A) Non-metallic,
Liquidtight, Conduit Grip Fittings
Straight with Male Fitting with Insulated Throat
Trade Size Dimensions Inches (cm) Catalog
N.P.T. Inches A B C D Numbers
3/8” 1.875” (4.76) .547” (1.39) 1.156” (2.94) 3.75” (9.52) H038CNK
1/2” 1.875” (4.76) .547” (1.39) 1.250” (3.17) 4.50” (11.43) H050CNK
3/4” 2.000” (5.08) .578” (1.47) 1.500” (3.81) 6.25” (15.87) H075CNK
1” 2.125” (5.40) .687” (1.74) 1.844” (4.68) 7.50” (19.05) H100CNK
11/4” 2.125” (5.40) .656” (1.67) 2.312” (5.87) 9.00” (22.86) H125CNK
11/2” 2.250” (5.71) .656” (1.67) 2.578” (6.55) 13.50” (34.29) H150CNK
2” 2.312” (5.87) .656” (1.67) 3.187” (8.09) 14.50” (36.83) H200CNK
90° Angle with Male Fitting with Insulated Throat
Trade Size Dimensions Inches (cm) Catalog
N.P.T. Inches E F G H I Numbers
3/8” 1.875” (4.76) .547” (1.39) 1.156” (2.94) 1.453” (3.69) 3.75” (9.52) H0389CNK
1/2” 1.875” (4.76) .547” (1.39) 1.250” (3.17) 1.453” (3.69) 4.50” (11.43) H0509CNK
3/4” 2.016” (5.12) .578” (1.47) 1.500” (3.81) 1.000” (2.54) 6.25” (15.87) H0759CNK
1” 2.375” (6.03) .687” (1.74) 1.894” (4.81) 2.125” (5.40) 7.50” (19.05) H1009CNK
11/4” 2.281” (5.79) .656” (1.67) 2.312” (5.87) 2.344” (5.95) 9.00” (22.86) H1259CNK
11/2” 2.562” (6.51) .656” (1.67) 2.578” (6.55) 2.500” (6.35) 13.50” (34.29) H1509CNK
2” 2.937” (7.46) .656” (1.67) 3.187” (8.09) 2.781” (7.06) 14.50” (36.83) H2009CNK
Dimensions shown are approximate and are subject to change without notice.
H
I
F
E
G
Flats
C
Flats
A
Ref.
B
Ref.
D
T-107
Dimensions in Inches (mm) www.hubbell-wiring.com
Non-metallic Liquidtight Conduit Wire Management Products
Non-metallic Liquidtight Conduit
Product Features and Benefits
POLYTUFF®Liquidtight Conduit
PolyTuff I Conduit–Gray
Rigid PVC core bonded to flexible PVC jacket.
All nonmetallic construction ends metal fatigue and
separation problems.
UL Listed and CSA Certified.
Cuts cleanly with a knife or PVC cutter so there
are no jagged metal edges.
T-108 Dimensions in Inches (mm)
www.hubbell-wiring.com
PolyTuff I Conduit
Trade Catalog
Size (metric designator) Numbers Feet (m)
3/8” (12) G1038 100 (30.5)
1/2” (16) G1050 100 (30.5)
3/4” (21) G1075 100 (30.5)
1” (27) G1100 100 (30.5)
11/4” (35) G1125 100 (30.5)
11/2” (41) G1150 50 (15.2)
2” (53) G1200 50 (15.2)
Note: See pages T-114 to T-115 for additional technical data and dimensional drawings.
IP66
SUITABILITY
Wire Management Products Non-metallic Liquidtight Tubing
Non-metallic Liquidtight Tubing
Product Features and Benefits
POLYTUFF®Liquidtight Conduit
PolyTuff II Tubing–Black
PVC core with corrugated walls bonded to PVC jacket.
H
andles twists, turns, bends, switchbacks and straightaways
w
ith ease.
All nonmetallic construction ends fatigue and
separation problems.
C
an be cut with a knife or PVC cutters.
UL Recognized and CSA Certified.
T-109
Dimensions in Inches (mm) www.hubbell-wiring.com
PolyTuff II Tubing
Trade Catalog
Size (metric designator) Numbers Feet (m)
1/4(10) B2025 100 (30.5)
3/8(12) B2038 100 (30.5)
1/2(16) B2050 100 (30.5)
3/4(21) B2075 100 (30.5)
1 (27) B2100 100 (30.5)
11/4(35) B2125 100 (30.5)
11/2(41) B2150 50 (15.2)
2 (53) B2200 50 (15.2)
Note: See pages T-114 to T-115 for additional technical data and dimensional drawings.
IP66
SUITABILITY
Nylon two-piece swivel body enables
fitting to twist from 0° to 90°.
Non-integral ferrule provides conduit seal and
superior pullout protection.
Nylon compression nut
has a tapered dome to
tighten ferrule onto
conduit.
Neoprene O-ring provides
liquidtight seal at hub or enclosure.
Nylon locknut fastens connector
securely to enclosure and provides superior
corrosion resistance.
Nonmetallic Liquidtight Connectors
Product Features and Benefits
POLYTUFF® Nonmetallic Connectors
Nonmetallic Liquidtight Fittings Wire Management Products
T-110 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Non-metallic Liquidtight Fittings
Non-metallic Liquidtight Connectors
Flexible Non-metallic Conduit and Tubing Fittings
POLYTUFF®Non-metallic Fittings
Type 4X, 12 and 13
PS05GYKIT
P1259NGY
PSO509NGY - SwivelLok
PSO509NGY - SwivelLok
P125NGY
P075NGYA
Straight with Male Non-Metallic Liquidtight Fittings
Trade Black Gray
Size
(metric designator)
Catalog Numbers Catalog Numbers
3/8” (12) P038NBKA P038NGYA
1/2” (16) P050NBKA P050NGYA
3/4” (21) P075NBKA P075NGYA
1” (27) P100NBKA P100NGYA
1/4” (10) F2025 –
11/4“(35) P125NBK P125NGY
11/2” (41) P150NBK P150NGY
2” (53) P200NBK P200NGY
Note: See pages T-116 and T-117 for additional technical data and dimensional
drawings.
SwivelLok®Multi-Position
with Male Non-Metallic Liquidtight Fittings
Trade Black Gray
Size
(metric designator)
Catalog Numbers Catalog Numbers
3/8” (12) PS0389NBK PS0389NGY
1/2” (16) PS0509NBK PS0509NGY
3/4” (21) PS0759NBK PS0759NGY
1” (27) PS1009NBK PS1009NGY
Note: See pages T-116 and T-117 for additional technical data and dimensional
drawings.
90° Angle with Male Non-Metallic Liquidtight Fittings
Trade Black Gray
Size
(metric designator)
Catalog Numbers Catalog Numbers
1/4” (10) F20259 –
11/4” (35) P1259NBK P1259NGY
Note: See pages T-116 and T-117 for additional technical data and dimensional
drawings.
SwivelLok Flexible Conduit Kit
Trade Size (metric designator)
Fitting and Conduit Catalog Numbers
1/2” (16) 2 PS0509NGY, 6’ G1050 PS05GYKIT
3/4” (21) 2 PS0759NGY, 6’ G1075 PS07GYKIT
Note: See pages T-116 and T-117 for additional technical data and dimensional
drawings.
T-111
Dimensions in Inches (mm) www.hubbell-wiring.com
Hexagonal, screw-machined steel thru 1", and
malleable iron on larger sizes. Nut compresses
gland-ring onto conduit.
Split, nylon, gland-ring compresses
conduit onto ferrule.
Non-integral, reusable steel,
ferrule is easily installed, to
seal conduit.
Threaded one-piece steel body.
Tapered, machined threads fasten securely and provide
additional liquidtight sealing.
Optional insulated and non-insulated throat.
Optional Neoprene O-ring provides liquidtight seal at hub.
Locknut has hardened steel tangs to grip securely.
Metallic Liquidtight Fittings
Product Features and Benefits
Flexible Metallic, Liquidtight Conduit Fittings
Metallic Liquidtight Fittings Wire Management Products
T-112 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Metallic Liquidtight Fittings
Metallic Liquidtight Fittings
Flexible Metallic Conduit Fittings
90˚ Angle with Male
Hubbell Conduit
Fitting
H0509
45˚ Angle with Male
Hubbell Conduit
Fitting
H05041
Straight with Male
Hubbell Conduit
Fitting
H0501
Straight Conduit Fitting
Trade Size (metric designator) Insulated Non-Insulated
3/8” (12) H0381 H038
1/2” (16) H0501 H050
3/4” (21) H0751 H075
1” (27) H1001 H100
11/4” (35) H1251 H125
11/2” (41) H1501 H150
2” (53) H2001 H200
21/2” (63) H2501 –
3” (78) H3001 –
Note: See page T-118 for additional technical data.
45° Conduit Fitting
Trade Size (metric designator) Insulated Non-Insulated
3/8” (12) H03841 H0384
1/2” (16) H05041 H0504
3/4” (21) H07541 H0754
1” (27) H10041 H1004
11/4” (35) H12541 H1254
11/2” (41) H15041 H1504
2” (53) H20041 H2004
Note: See page T-118 for additional technical data.
90° Conduit Fitting
Trade Size (metric designator) Insulated Non-Insulated
3/8” (12) H03891 H0389
1/2” (16) H05091 H0509
3/4” (21) H07591 H0759
1” (27) H10091 H1009
11/4” (35) H12591 H1259
11/2” (41) H15091 H1509
2” (53) H20091 H2009
Note: See page T-118 for additional technical data.
T-113
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Non-metallic Liquidtight Conduit and Tubing
Technical Data
POLYTUFF®
PolyTuff I Conduit
Operating Temperature Range
Wet environment 0°F to +140°F (-18°C to +60°C)
Oil environment 0°F to +158°F (-18°C to +70°C)
Dry environment 0°F to +176°F (-18°C to +80°C)
Certifications
UL Listed, UL Standard 1660.
Sunlight resistant approved for outdoor use, direct burial.
CSA Certified Meets requirements of NEC Article 351-B
Voltage Rating
Maximum 600V
Material
Conduit Co-extruded rigid and flexible PVC.
PolyTuff II Tubing
Operating Temperature Range
Operating Environment 0°F to +140°F (-18°C to +60°C)
Certifications
UL Recognized
CSA Certified
Voltage Rating
Maximum Same as wire insulation rating.
Material
Tubing Co-extruded rigid and flexible PVC.
T-114 Dimensions in Inches (mm)
www.hubbell-wiring.com
PolyTuff I Conduit
Trade Size
(metric
Conduit ID/OD Bend Radius
designator)
Inches (mm) Inches (mm)
3/8” (12) .49”/.70” (12.6/17.8) 2.00” (50.8)
1/2” (16) .63”/.83” (16.1/21.1) 3.00” (76.2)
3/4” (21) .83”/1.04” (21.1/26.4) 4.00” (101.6)
1” (27) 1.05”/1.30” (26.0/33.1) 5.00” (217.0)
11/4” (35) 1.40”/1.65” (35.4/41.8) 6.30” (158.8)
11/2” (41) 1.59”/1.88” (40.3/47.8) 7.50” (190.5)
2” (53) 2.03”/2.36” (51.6/59.9) 10.00” (254.0)
PolyTuff II Tubing
Trade Size
(metric
Conduit ID/OD Bend Radius
designator)
Inches (mm) Inches (mm)
1/4”(10) .36”/.57” (9.3/14.5) 1.50” (38.1)
3/8” (12) .49”/.70” (12.6/17.8) 2.00” (50.8)
1/2” (16) .63”/.83” (16.1/21.1) 2.00” (50.8)
3/4” (21) .83”/1.04” (21.1/26.4) 3.00” (76.2)
1” (27) 1.05”/1.30” (26.0/33.1) 3.00” (76.2)
11/4” (35) 1.40”/1.65” (35.4/41.8) 5.00” (127.0)
11/2” (41) 1.59”/1.88” (40.3/47.8) 5.00” (127.0)
2” (53) 2.03”/2.36” (51.6/59.9) 5.00” (127.0)
Wire Management Products Technical Data
Non-metallic Liquidtight Conduit and Tubing
Technical Data
POLYTUFF®
PolyTuff I and II Conduit/Tubing; PVC Chemical Resistance
Temp. Temp. Temp.
Chemical Conc* 70°F 150°F Chemical Conc* 70°F 150°F Chemical Conc* 70°F 150°F
21°C 66°C 21°C 66°C 21°C 66°C
T-115
Dimensions in Inches (mm) www.hubbell-wiring.com
Acetate Solvents D D
Acetic Acid B C
Acetic Acid (Glacial) C D
Acetone D D
Acrylontrile A B
Alcohols (Aliphatic) C C
Aluminum Chloride A A
Aluminum Sulfate (Alums) A A
Ammonia
(Anhydrous Liquids) D D
Ammonia (Aqueous) A A
Ammoniated Latex A C
Ammonium Chloride A A
Ammonium Hydroxide A A
Amyl Acetate D D
Aniline Oils D D
Aromatic Hydrocarbons D D
Asphalt D D
ASTM Fuel A C C
ASTM Fuel B D D
ASTM #1 Oil B C
ASTM #3 Oil C D
Barium Chloride A A
Barium Sulfide A A
Barium Hydroxide A A
Benzene (Benzol) D D
Benzine (Petroleum Ether) C C
Black Liquor A A
Bordeaux Mixture A A
Boric Acid A A
Butyl Acetate D D
Butyl Alcohol B C
Calcium Hydroxide A A
Calcium Hypochlorite A A
Carbolic Acid (Phenol) B C
Carbon Dioxide A A
Carbon Disulfide D D
Carbon Tetrachloride D D
Carbonic Acid A A
Casein A C
Caustic Soda A B
Chlorine Gas (wet) D D
Chlorine Gas (dry) D D
Chlorine (water solution) C D
Chlorobenzene D D
Chlorinated Hydrocarbons D D
Chromic Acid B C
Citric Acid A A
Coal Tar D D
Coconut Oil C D
Corn Oil A B
Cottonseed Oil C D
Creosote D D
Cresol C D
Crysylic Acid D D
Cyclohexane B C
DDT Weed Killer A C
Dibutyl Phthalate D D
Diesel Oils C D
Diethylene Glycol B C
Diethyl Ether A C
Di-isodecyl Phthalate D D
Dioctyl Phthalate D D
Dow General Weed Killer (Phenol) D D
Dow General Weed Killer (H2O) B C
Ethyl Alcohol C C
Ethylene Dichloride D D
Ethylene Glycol B C
Ferric Chloride A A
Ferric Sulfate A A
Ferrous Chloride A A
Ferrous Sulfate A A
Formaldehyde D D
Fuel Oil B C
Furfural C C
Gallic Acid A A
Gasoline (Hi Test) C D
Glycerine A A
Grease A C
Green Sulfate Liquor A A
Heptachlor in
Petroleum Solvents A C
Heptane C D
Hexane C D
Hydrobromic Acid A A
Hydrochloric Acid 10% A A
Hydrochloric Acid 40% C C
Hydrofluoric Acid 70% D D
Hydrofluorosilicic Acid A A
Hydrofluorosilicic Acid 10% A A
Hydrogen Peroxide A B
Iso-Octane C C
Isopropyl Acetate D D
Isopropyl Acid B C
Jet Fuels (JP-3, and 5) C D
Kerosene C C
Ketones D D
Linseed Oil A A
Lubricating Oils A A
Magnesium Chloride A A
Magnesium Hydroxide A A
Magnesium Sulfate A A
Malathion 50 in Aromatics D D
Malic Acid A A
Methyl Acetate D D
Methyl Alcohol C C
Methyl Bromide D D
Methyl Ethyl Ketone D D
Methylene Chloride D D
Mineral Oil
Monochlorobenezene A A
Muriatic Acid
(see Hydrochloric Acid)
Naphtha C D
Naphthalene D D
Nitric Acid 10% A B
Nitric Acid 35% A C
Nitric Acid 70% D D
Oleic Acid A C
Oleum D D
Oxalic Acid A A
Pentachlorophenol in Oil B C
Pentane C D
Perchloroethylene B C
Petroleum Ether C C
Phenol A A
Phosphoric Acid 10% A A
Pitch 50% A B
Potassium Hydroxide C D
Sodium Cyanide A A
Stoddard Solvent D D
Styrene D D
Sulfur Dioxide (liquid) D D
Sulfuric Acid 50% A B
Sulfuric Acid 98% D D
Sulfurous Acid B C
Tall Oil D D
Tannic Acid A A
Toluene D D
Trichlorethylene D D
Triethanol Amine C D
Tricresyl Phosphate (Skydrol) D D
Turpentine C D
Vinegar A B
Vinyl Chloride D D
Water A A
White Liquor A A
Xylene D D
Zinc Chloride A A
Zinc Sulfate A A
Rating Code
A-Excellent service
No harmful effect to reduce service life. Suitable for continuous service.
B-Good service life.
Moderate to minor effect. Good for intermittent service. Generally suitable
for continuous service.
C-Fair or limited service.
Depends on operating conditions. Generally suitable for intermittent
service. Not recommended for continuous service.
D-Unsatisfactory service.
Not recommended.
(All ratings apply to concentrated or saturated solutions unless otherwise specified.)
Chemical resistance ratings are based upon information supplied by the raw material
manufacturers. Use as a general guide only – samples should be tested by user under
actual conditions.
*Conc. - Concentration
Technical Data Wire Management Products
Non-metallic Liquidtight Fittings
Technical Data
POLYTUFF®Fittings
PolyTuff Fittings
Operating Temperature*
Nylon (Body, Nut, Gripping Ring and Locknut) –40°F to +225°F (–40°C to +107°C).
Neoprene (Sealing Ring) –30°F to +240°F (–34°C to +116°C).
Flammability
Fire Gas Toxicity Product Testing Nylon PolyTuff Fittings have a UL 94V-2 rating.
Certifications
UL Listed UL50 Type 4X, 12 and 13
CSA Certified PolyTuff I Fittings, Poly Tuff II Fittings.
Liquidtight Fittings
Operating Temperature**
Steel/Malleable Iron (Nut, Body, Ferrule) –60°F to +1000°F (–51°C to +538°C).
Nylon (Gland Ring) –40°F to +225°F (–40°C to +107°C).
Hazardous Locations NEC Reference
Class I, Div. 2 501-4b
Class II, Div. 1 502-4a2
Class II, Div. 2 502-4b2
Class III, Div. 1 503-3a2
Class III, Div. 2 503-3b
Certifications
UL Listed
CSA Certified
*Due to the limiting factors of nylon and neoprene, PolyTuff Fittings will continuously perform in the range –30°F to +225°F
(–34°C to +107°C).
**Due to the limiting factors of nylon, metallic liquidtight flexible conduit fittings will continuously perform in the range of –40°F to
+225°F (–40°C to +107°C).
T-116 Dimensions in Inches (mm)
www.hubbell-wiring.com
Wire Management Products Technical Data
Non-metallic Liquidtight Fittings
Technical Data
POLYTUFF®Fittings
C
B
Straight Position
A
Dia.
B
D
C
E
B
D
E
A
C
Sizes: 3/8", 1/2", 3/4", 1"
Sizes: 1/4", 11/4", 11/2", 2"
A
Dia.
C
E
B
D
Straight with Male Non-Metallic Liquidtight Fittings
Trade A B C D E
Size Throat
(md**) Dia. A/C* A/F*
1/4”
.93” 1.45” .39” .32” .86” (Dia.)
(10) (23.6) (36.8) (9.9) (8.1) (21.8)
3/8”
1.14” 1.63” .57” .42” 1.41” 1.30”
(12) (29.0) (41.4) (14.5) (10.7) (35.8) (33.0)
1/2”
1.30” 2.14” .57” .55” 1.41” 1.30”
(16) (33.0) (54.4) (14.5) (14.0) (35.8) (33.0)
3/4”
1.53” 2.22” .58” .74” 1.85” 1.53”
(21) (38.9) (56.4) (14.7) (18.8) (47.0) (38.9)
1
”
1.80” 2.32” .72” .96” 1.94” 1.80”
(27) (45.7) (58.9) (18.3) (24.4) (49.3) (45.7)
1
1/4”
2.20” 2.15” .74” 1.30” 2.38” 2.18”
(35) (55.9) (54.6) (18.8) (33.0) (60.5) (55.4)
1
1/2”
2.49” 2.35” .76” 1.46” 2.63” 2.43”
(41) (63.2) (59.7) (19.3) (37.1) (66.8) (61.7)
2
”
3.05” 2.51” .79” 1.90” 3.13” 2.93”
(53) (77.4) (63.6) (20.1) (48.3) (79.5) (74.4)
*A/C = Across Corners A/F = Across Flats **md = metric designator
90° with Male Non-Metallic Liquidtight Fittings
Trade A B C D E
Size Throat
(md**) Dia. A/C* A/F*
1/4
” .93” 1.88” .39” .32” .86”(Dia.)
(10) (23.6) (47.8) (9.9) (8.1) (21.8)
1
1/4
” 2.21” 3.57” .74” 1.30” 2.38” 2.18”
(35) (56.1) (90.7) (18.9) (33.0) (60.5) (55.4)
*A/C = Across Corners A/F = Across Flats **md = metric designator
SwivelLok®Multi-Position Liquidtight Fittings
Trade A B C D E F G
Size
(md**) A/C* A/F*
3/8
” 1.30
”
3.27
”
.57
”
.55
”
1.43
”
2.00
”
1.41
”
1.30
”
(12) (33.0) (83.1) (14.5) (14.0) (36.3) (50.8) (35.8) (33.0)
1/2
” 1.30
”
3.27
”
.57
”
.55
”
1.43
”
2.00
”
1.41
”
1.30
”
(16) (33.0) (83.1) (14.5) (14.0) (36.3) (50.8) (35.8) (33.0)
3/4
” 1.53
”
3.66
”
.58
”
.74
”
1.59
”
2.23
”
1.65
”
1.53
”
(21) (38.9) (93.0) (15.7) (18.8) (40.4) (56.6) (41.9) (38.9)
1” 1.80
”
4.00
”
.72
”
.96
”
1.84
”
2.30
”
1.94
”
1.80
”
(27) (45.7) (101.6) (18.3) (24.4) (46.7) (58.4) (49.3) (45.7)
*A/C = Across Corners A/F = Across Flats **md = metric designator
45° Position
D
A
G
90° Position
F
E
T-117
Dimensions in Inches (mm) www.hubbell-wiring.com
Technical Data Wire Management Products
Metallic Liquidtight Conduit Fittings
Technical Data
T-118 Dimensions in Inches (mm)
www.hubbell-wiring.com
A
E
Throat
Dia.
B
D
CF
B
E
Throat
Dia.
D
C
A
F
D
Throat
Dia.
E
C
A
B
Ref.
Straight with Male Metallic Metal Fitting
Trade A B C D E
Size Throat
(md**) Ref. A/C* A/F* Dia. A/C* A/F*
3/8
”
1.43” .59” 1.20” 1.06” .61” 1.07” .93”
(12) (36.3) (15.0) (30.0) (26.9) (15.5) (27.2) (23.6)
1/2
”
1.43” .59” 1.34” 1.19” .61” 1.22” 1.06”
(16) (36.3) (15.0) (34.0) (30.2) (15.5) (31.0) (26.9)
3/4
”
1.56” .59” 1.55” 1.37” .84” 1.43” 1.25”
(21) (39.6) (15.0) (39.0) (34.8) (21.3) (36.3) (31.8)
1
”
1.68” .66” 1.95” 1.69” 1.06” 1.73” 1.56”
(27) (42.7) (16.8) (50.0) (42.9) (26.9) (43.9) (39.6)
11/4
”
2.03” .63” 2.39” 2.06” 1.37” 2.36” 2.08”
(35) (51.6) (16.8) (61.0) (52.3) (34.8) (59.9) (52.8)
11/2
”
2.21” .63” 2.72” 2.38” 1.53” 2.79” 2.48”
(41) (56.1) (16.8) (69.0) (60.5) (38.9) (70.9) (63.0)
2
”
2.28” .69” 3.08” 2.87” 2.06” 3.32” 2.90”
(53) (57.9) (17.5) (78.0) (72.9) (52.3) (84.3) (73.7)
21/2
”
3.56” 1.06” 3.92” 3.62” 2.42” 3.85” 3.60”
(63) (90.4) (26.9) (100.0) (91.9) (61.5) (97.8) (91.4)
3
”
3.81” 1.06” 4.70” 4.31” 3.01” 4.65” 4.33”
(78) (96.8) (26.9) (119.0) (109.5) (76.5) (118.1) (110.0)
31/2
”
3.81” 1.06” 5.29” 4.81” 3.49” 5.18” 4.82”
(91) (96.8) (26.9) (134.0) (122.2) (88.6) (131.6) (122.4)
4
”
3.81” 1.06” 5.75” 5.31” 3.96” 5.75” 5.39”
(103) (96.8) (26.9) (146.0) (134.9) (100.6) (146.1) (136.9)
45° with Male Metallic Metal Fitting
Trade A B C D E F
Size Throat
(md**) A/C* A/F* Dia. A/C* A/F*
3/8
”
1.19” 1.28” .59” 1.20” 1.06” .60” 1.16” 1.02”
(12) (30.2) (32.5) (15.0) (30.5) (26.9) (15.2) (29.5) (25.9)
1/2
”
1.19” 1.28” .59” 1.34” 1.19” .61” 1.21” 1.06”
(16) (30.2) (32.5) (15.0) (34.0) (30.2) (15.2) (30.7) (26.9)
3/4
”
1.19” 1.43” .59” 1.55” 1.45” .84” 1.50” 1.32”
(21) (30.2) (36.3) (15.0) (39.4) (36.8) (21.3) (38.1) (33.5)
1
”
1.38” 1.53” .66” 1.95” 1.69” 1.05” 1.82” 1.59”
(27) (35.1) (38.9) (16.8) (49.5) (42.9) (26.7) (46.2) (40.4)
11/4
”
1.42” 1.69” .63” 2.39” 2.06” 1.37” 2.32” 2.03”
(35) (36.1) (42.9) (16.0) (60.7) (52.3) (34.8) (58.9) (5.16)
11/2
”
1.66” 2.00” .66” 2.72” 2.38” 1.60” 2.62” 2.29”
(41) (42.2) (50.8) (16.8) (69.1) (60.5) (40.6) (66.5) (58.2)
2
”
1.69” 2.25” .66” 3.08” 2.88” 2.05” 3.21” 2.80”
(53) (42.9) (57.2) (16.8) (78.2) (73.2) (52.1) (81.5) (71.1)
90° with Male Metallic Metal Fitting
Trade A B C D E F
Size Throat
(md**) A/C* A/F* Ref. Dia. A/C* A/F*
3/8
”
1.31” .59” 1.20” 1.06” 1.44” .60” 1.13” .99”
(12) (33.3) (15.0) (30.5) (26.9) (36.6) (15.2) (29.0) (25.1)
1/2
”
1.31” .59” 1.34” 1.12” 1.44” .61” 1.12” 1.00”
(16) (33.3) (15.0) (34.0) (28.4) (36.6) (15.5) (28.0) (25.4)
3/4
”
1.44” .59” 1.55” 1.45” 1.63” .83” 1.48” 1.29”
(21) (36.6) (15.0) (39.4) (36.8) (41.4) (21.1) (38.0) (32.8)
1
”
1.78” .59” 1.95” 1.60” 2.19” 1.05” 1.80” 1.57”
(27) (45.2) (15.0) (49.5) (40.6) (55.6) (26.7) (46.0) (39.9)
11/4
”
1.97” .63” 2.39” 2.06” 2.50” 1.36” 2.32” 2.02”
(35) (50.0) (16.0) (60.7) (52.3) (63.5) (34.5) (59.0) (51.3)
11/2
”
2.19” .63” 2.72” 2.38” 2.69” 1.61” 2.58” 2.25”
(41) (55.6) (16.0) (69.1) (60.5) (68.3) (40.9) (66.0) (57.2)
2
”
2.53” .66” 3.08” 2.87” 3.25” 2.05” 3.14” 2.75”
(53) (64.3) (16.8) (78.2) (72.9) (82.6) (52.1) (80.0) (69.9)
21/2
”
3.44” 1.00” 3.92” 3.63” 4.25” 2.42” 3.78” 3.50”
(63) (87.4) (25.4) (99.6) (92.2) (108.0) (61.5) (96.0) (88.9)
3
”
3.75” 1.00” 4.70” 4.31” 4.87” 3.01” 4.64” 4.30”
(78) (95.3) (25.4) (119.4) (109.5) (123.7) (76.5) (118.0) (109.2)
4
”
4.25” 1.00” 5.75” 5.31” 5.63” 3.96” 5.76” 5.38”
(103) (108.0) (25.4) (146.1) (134.9) (143.0) (100.6) (146.0) (136.7)
*A/C = Across Corners A/F = Across Flats **md = metric designator