NL7SZ98 Configurable Multifunction Gate The NL7SZ98 is an advanced high-speed CMOS multifunction gate. The device allows the user to choose logic functions MUX, AND, OR, NAND, NOR, INVERT and BUFFER. The device has Schmitt-trigger inputs, thereby enhancing noise immunity. The NL7SZ98 input and output structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. http://onsemi.com Features * * * * * * * 1 High Speed: tPD = 3.4 ns (Typ) @ VCC = 5.0 V Low Power Dissipation: ICC = 1 mA (Maximum) at TA = 25C Power Down Protection Provided on inputs Balanced Propagation Delays Overvoltage Tolerant (OVT) Input and Output Pins Ultra-Small Package This is a Pb-Free Device SC-88 (SOT-363) CASE 419B MARKING DIAGRAM 6 MP MG G 1 MP = Specific Device Code M = Date Code G = Pb-Free Package (Note: Microdot may be in either location) PIN ASSIGNMENTS IN B 1 6 IN C GND 2 5 VCC IN A 3 4 OUT Y (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. (c) Semiconductor Components Industries, LLC, 2009 November, 2009 - Rev. 2 1 Publication Order Number: NL7SZ98/D NL7SZ98 IN A OUT Y IN B IN C Figure 1. Function Diagram PIN ASSIGNMENT FUNCTION TABLE* 1 IN B 2 GND A B C Y 3 IN A L L L H 4 OUT Y L L H H 5 VCC L H L L 6 IN C L H H H H L L H H L H L H H L L H H H L Input Output *To select a logic function, please refer to "Logic Configurations section". http://onsemi.com 2 NL7SZ98 LOGIC CONFIGURATIONS VCC B B Y A A 1 6 2 5 3 4 VCC C A Y C Y A 1 6 2 5 3 4 C Y C Figure 2. 2-Input MUX with Output Inverted Figure 3. 2-Input NAND (When B = "L") VCC VCC A C A C B Y A 1 6 2 5 3 4 Y C C Y B Y B Y C 1 6 2 5 3 4 C Y Figure 4. 2-Input NOR with Input C Inverted (When B = "H") Figure 5. 2-Input NAND with Input C Inverted (When A = "L") VCC VCC B C B Y 1 6 2 5 3 4 C C Y Y Figure 6. 2-Input NOR (When A ="H") 6 2 5 3 4 C Y Figure 7. Buffer (When A = "L" and B = "H") VCC B B 1 Y 1 6 2 5 3 4 Y Figure 8. Inverter (When A = C = "L") http://onsemi.com 3 NL7SZ98 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage -0.5 to +7.0 V VIN DC Input Voltage -0.5 to +7.0 V DC Output Voltage -0.5 to +7.0 V VIN < GND -50 mA VOUT < GND -50 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current $50 mA ICC DC Supply Current Per Supply Pin $100 mA IGND DC Ground Current per Ground Pin $100 mA TSTG Storage Temperature Range -65 to +150 C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 C TJ Junction Temperature Under Bias +150 C qJA Thermal Resistance (Note 1) SC-88 350 C/W PD Power Dissipation in Still Air at 85C SC-88 200 mW MSL FR VESD ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 ESD Withstand Voltage UL 94 V-0 @ 0.125 in Human Body Mode (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Latchup Performance Above VCC and Below GND at 125C (Note 5) >2000 >200 N/A V $500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm by 1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V -55 +125 C 0 0 0 No Limit No Limit No Limit nS/V VOUT TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 2.5 V $ 0.2 V VCC = 3.3 V $ 0.3 V VCC = 5.0 V $ 0.5 V http://onsemi.com 4 NL7SZ98 DC ELECTRICAL CHARACTERISTICS Symbol Parameter VT+ Positive Threshold Voltage VT- VH VOH VOL Conditions Negative Threshold Voltage Hysteresis Voltage Minimum High-Level Output Voltage Maximum Low-Level Output Voltage TA = 255C VCC (V) Min 1.65 0.79 1.16 2.3 1.11 3.0 4.5 5.5 Typ Max TA v +855C TA = -555C to +1255C Min Min Max Max Unit 1.16 1.16 V 1.56 1.56 1.56 1.5 1.87 1.87 1.87 2.16 2.74 2.74 2.74 2.61 3.33 3.33 3.33 1.65 0.35 0.62 0.35 0.35 2.3 0.58 0.87 0.58 0.58 3.0 0.84 1.19 0.84 0.84 4.5 1.41 1.9 1.41 1.41 5.5 1.78 2.29 1.78 1.78 1.65 0.30 0.62 0.30 0.62 0.30 0.62 2.3 0.40 0.8 0.40 0.8 0.40 0.8 3.0 0.53 0.87 0.53 0.87 0.53 0.87 4.5 0.71 1.04 0.71 1.04 0.71 1.04 1.2 0.8 1.2 0.8 1.2 V 5.5 0.8 1.65 - 5.5 VCC - 0.1 VCC - 0.1 VCC - 0.1 IOH = -4 mA 1.65 1.2 1.2 1.2 IOH = -8 mA 2.3 1.9 1.9 1.9 IOH = -16 mA 3.0 2.4 2.4 2.4 IOH = -24 mA 3.0 2.3 2.3 2.3 IOH = -32 mA 4.5 3.8 3.8 3.8 VIN w VT+MAX IOL = 50 mA 1.65 - 5.5 0.1 0.1 0.1 IOL = 4 mA 1.65 0.45 0.45 0.45 IOL = 8 mA 2.3 0.3 0.3 0.3 IOL = 16 mA 3.0 0.4 0.4 0.4 IOL = 24 mA 3.0 0.55 0.55 0.55 IOL = 32 mA 4.5 0.55 0.55 0.55 VIN v VT-MIN IOH = -50 mA V V VIN v VT-MIN V VIN w VT+MAX IIN Input Leakage Current 0 v VIN v 5.5 V 0 to 5.5 $0.1 $1.0 $1.0 mA ICC Quiescent Supply Current 0 v VIN v VCC 5.5 1.0 10 10 mA http://onsemi.com 5 NL7SZ98 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = 255C Typ Max Min Max Min Max Unit 1.65 - 1.95 3.2 8.9 14.4 3.2 14.4 3.2 14.4 ns 2.3 - 2.7 2.0 5.2 8.3 2.0 8.3 2.0 8.3 3.0 - 3.6 1.5 4.0 6.3 1.5 6.3 1.5 6.3 4.5 - 5.5 1.1 3.4 5.1 1.1 5.1 1.1 5.1 Parameter VCC (V) tPLH, tPHL Propagation Delay, Any Input to Output Y (See Test Circuit) Input Capacitance CPD Power Dissipation Capacitance (Note 6) TA = -555C to +1255C Min Symbol CIN TA v +855C Test Condition 5.0 f = 10 MHz 3.5 pF 22 pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD * VCC * fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD * VCC2 * fin + ICC * VCC. TEST CIRCUIT AND VOLTAGE WAVEFORMS From Output Under Test VLOAD RL Test S1 tPLH/tPHL Open tPLZ/tPZL VLOAD tPHZ/tPZH GND Open GND CL * RL *CL includes probes and jig capacitance. Figure 9. Load Circuit Inputs VCC VI tr/tf VM VLOAD CL RL VD 1.8 V $ 0.15 V VCC v 2 ns VCC/2 2 x VCC 30 pF 1 kW 0.15 V 2.5 V $ 0.2 V VCC v 2 ns VCC/2 2 x VCC 30 pF 500 W 0.15 V 3.3 V $ 0.3 V 3V v 2.5 ns 1.5 V 6V 50 pF 500 W 0.3 V 5.5 V $ 0.5 V VCC v 2.5 ns VCC/2 2 x VCC 50 pF 500 W 0.3 V http://onsemi.com 6 NL7SZ98 Timing Input tW Input VI VM VM tsu 0V Data Input Figure 10. Voltage Waveforms Pulse Duration Input VM VM tPHL Output VM tPLH VM Output Control 0V tPHL tPLH Output VM 0V th VM VI VM 0V Figure 11. Voltage Waveforms Setup and Hold Times VI VM VI VM Output Waveform 1 S1 at VLOAD (Note 7) VOH VOL VM VM VM tPZH VOH Output Waveform 2 S1 at GND (Note 8) VOL Figure 12. Voltage Waveforms Propagation Delay Times Inverting and Noninverting Outputs VM VI 0V VLOAD/2 VOL + VD VOL tPHZ VOH VOH - VD [0 V Figure 13. Voltage Waveforms Enable and Disable Times Low- and High-Level Enabling 7. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. 8. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control 9. All input pulses are supplied by generators having the following characteristics: PRR v 10 MHz, ZO = 50 W. 10. The outputs are measured one at a time, with one transition per measurement. 11. All parameters are waveforms are not applicable to all devices. ORDERING INFORMATION Device NL7SZ98DFT2G Package Shipping SC-88 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 NL7SZ98 PACKAGE DIMENSIONS SC-88/SC70-6/SOT-363 CASE 419B-02 ISSUE W NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419B-01 OBSOLETE, NEW STANDARD 419B-02. D e 6 5 4 1 2 3 HE DIM A A1 A3 b C D E e L HE -E- b 6 PL 0.2 (0.008) M E M MILLIMETERS MIN NOM MAX 0.80 0.95 1.10 0.00 0.05 0.10 0.20 REF 0.10 0.21 0.30 0.10 0.14 0.25 1.80 2.00 2.20 1.15 1.25 1.35 0.65 BSC 0.10 0.20 0.30 2.00 2.10 2.20 INCHES NOM MAX 0.037 0.043 0.002 0.004 0.008 REF 0.004 0.008 0.012 0.004 0.005 0.010 0.070 0.078 0.086 0.045 0.049 0.053 0.026 BSC 0.004 0.008 0.012 0.078 0.082 0.086 MIN 0.031 0.000 SOLDERING FOOTPRINT* A3 C 0.50 0.0197 A A1 L 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL7SZ98/D