MCC omponents 21201 Itasca Street Chatsworth !"# $ % !"# ES1DSR Features * * * * * For Surface Mount Applications Extremely Low Thermal Resistance Easy Pick And Place High Temp Soldering: 250C for 10 Seconds At Terminals Superfast Recovery Times For High Efficiency Maximum Ratings * * * 1 Amp Soft Recovery Rectifier 200 Volts Operating Temperature: -50C to +150C Storage Temperature: -50C to +150C Maximum Thermal Resistance; 15 C/W Junction To Lead MCC Device Maximum Maximum Maximum Catalog Marking Recurrent RMS DC Number Peak Reverse Voltage Blocking Voltage Voltage ES1DSR ES1D 200V 140V DO-214AC (SMAJ) (High Profile) H Cathode Band 200V J Electrical Characteristics @ 25C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time Typical Junction Capacitance IF(AV) IFSM 1.0A 30A A TJ = 75C E D F 8.3ms, half sine C B G DIMENSIONS VF .97V IFM = 1.0A; TJ = 25C* IR 5A 30A TJ = 25C TJ = 125C DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 SUGGESTED SOLDER PAD LAYOUT Trr 50ns CJ 45pF IF=0.5A, IR=1.0A, Irr=0.25A Measured at 1.0MHz, VR=4.0V 0.090" 0.085" 0.070" *Pulse test: Pulse width 200 sec, Duty cycle 2% www.mccsemi.com NOTE MCC ES1DSR Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 2.4 6 2.2 4 2.0 1.8 2 1.6 25C Amps 1.4 1 1.2 .6 Amps .4 1.0 .8 .6 .2 .4 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load .1 .06 0 .04 25 50 75 100 125 150 C Average Forward Rectified Current - Amperesversus Ambient Temperature - C .02 .01 0 .2 .4 .6 .8 1.0 1.2 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com 400 1000 MCC ES1DSR Figure 4 Peak Forward Surge Current 30 Figure 5 New SMA Assembly 25 20 15 Amps 10 Round Lead Process 5 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50 10 trr +0.5A 0 Pulse Generator Note 2 25Vdc 1 Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com