DS3695A, DS3695AT, DS3696A www.ti.com SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 DS3695A/DS3695AT/DS3696A Multipoint RS485/RS422 Transceivers Check for Samples: DS3695A, DS3695AT, DS3696A FEATURES DESCRIPTION * The DS3695A and DS3696A are high speed differential TRI-STATE bus/line transceivers designed to meet the requirements of EIA standard RS485 with extended common mode range (+12V to -7V), for multipoint data transmission. In addition they are compatible with requirements of RS-422. 1 2 * * * * * * * * Meets EIA Standard RS485 for Multipoint Bus Transmission and is Compatible with RS-422 10 Ns Driver Propagation Delays (Typical) Single +5V Supply -7V to +12V Bus Common Mode Range Permits 7V Ground Difference between Devices on the Bus Thermal Shutdown Protection High Impedance to Bus with Driver in TRISTATE or with Power Off, over the Entire Common Mode Range Allows the Unused Devices on the Bus to be Powered Down Combined Impedance of a Driver Output and Receiver Input is less than One RS485 Unit Load, Allowing up to 32 Transceivers on the Bus 70 mV Typical Receiver Hysteresis Available in SOIC Packaging The driver and receiver outputs feature TRI-STATE capability. The driver outputs remain in over the entire common mode range of +12V to -7V. Bus faults that cause excessive power dissipation within the device trigger a thermal shutdown circuit, which forces the driver outputs into the high impedance state. The DS3696A provides an output pin (TS) which reports the thermal shutdown of the device. TS is an "open collector" pin with an internal 10 k pullup resistor. This allows the TS outputs of several devices to be wire OR-ed. Both AC and DC specifications are guaranteed over the 0C to 70C temperature and 4.75V to 5.25V supply voltage range. Connection and Logic Diagrams Figure 1. Molded Package, Small Outline (D0008A) Top View Figure 2. Top View (See Package Number D0008A) TS was LF (Line Fault) on previous datasheets, TS goes low upon thermal shutdown. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1996-2013, Texas Instruments Incorporated DS3695A, DS3695AT, DS3696A SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage, VCC 7V Control Input Voltages 7V Driver Input Voltage 7V Driver Output Voltages +15V/-10V Receiver Input Voltages +15V/-10V Receiver Output Voltage 5.5V Continuous Power Dissipation @ 25C D0008A Package 630 mW -65C to +150C Storage Temp. Range Lead Temp. (Soldering 4 seconds) (1) (3) 260C "Absolute maximum ratings" are those beyond which the safety of the device cannot be verified. They are not meant to imply that the device should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Derate linearly at 6.5 mW/C to 337 mW at 70C. (2) (3) Recommended Operating Conditions Supply Voltage, VCC Bus Voltage Min Max Units 4.75 5.25 V -7 +12 V Operating Free Air Temperature (TA) Commercial (DS3695AM) Industrial (DS3695ATM) Commercial (DS3696AM) Electrical Characteristics 0 +70 C -40 +85 C 0 +70 C Typ Max Units 5 V (1) (2) 0C TA 70C, 4.75V < VCC < 5.25V unless otherwise specified Parameter VOD1 VOD2 Test Conditions Differential Driver Output Voltage (Unloaded) Differential Driver Output Voltage (with Load) Min IO = 0 R = 50; (RS-422) (3) 2 R = 27; (RS-485) V 1.5 V VOD Complementary Output States Differential Output Voltage For Change in Magnitude of Driver VOC Driver Common Mode Output Voltage 3.0 V |VOC| Change in Magnitude of Driver Common Mode Output Voltage For Complementary Output States 0.2 V VIH Input High Voltage VIL Input Low Voltage VCL Input Clamp Voltage IIN = -18 mA -1.5 V IIL Input Low Current VIL = 0.4V -200 A IIH Input High Current VIH = 2.4V 20 A (1) (2) (3) 2 R = 27 0.2 DI, DE, RE , RE/DE 2 V V 0.8 V All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. All typicals are given for VCC = 5V and TA = 25C. All limits for which this note is applied must be derated by 10% for DS3695AT. Other parameters remain the same for this extended temperature range device (-40C TA +85C). Submit Documentation Feedback Copyright (c) 1996-2013, Texas Instruments Incorporated Product Folder Links: DS3695A DS3695AT DS3696A DS3695A, DS3695AT, DS3696A www.ti.com SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 Electrical Characteristics (1) (2) (continued) 0C TA 70C, 4.75V < VCC < 5.25V unless otherwise specified Parameter IIN Test Conditions Input Current RI, RI, DO/RI, DO/RI VCC = 0V or 5.25V, DE or RE /DE = 0V VTH Differential Input Threshold Voltage for Receiver -7V VCM +12V VTH Receiver Input Hysteresis VCM = 0V VOH Receiver Output High Voltage VOL Output Low Voltage Max Units VIN = 12V +1.0 mA VIN = -7V -0.8 mA IOH = -400 A IOL = 16 mA TS V 0.5 V IOL = 8 mA 0.45 V 20 A 0.4V VO 2.4V, VCC = Max, RIN Receiver Input Resistance -7V VCM +12V ICC Supply Current No Load (3) Output Current Receiver Short-Circuit V mV 2.4 (3) Output Current at Receiver OFF-State (High Impedance) IOSR +0.2 70 RO Output Current Driver Short-Circuit Typ -0.2 IOZR IOSD Min VO = -7V 12 k Driver Outputs Enabled 42 60 mA Driver Outputs Disabled 27 40 mA -250 mA +250 mA (3) VO = +12V (3) -15 VO = 0V -85 mA Receiver Switching Characteristics 0C TA 70C, 4.75V < VCC < 5.25V unless otherwise specified Symbol (4) Min Typ Max Units tPLH CL = 15 pF 15 28 42 ns tPHL S1 and S2 15 28 42 ns |tPLH-tPHL| Closed 0 3 tPLZ CL = 15 pF, S2 Open 5 29 35 ns tPHZ CL = 15 pF, S1 Open 5 12 16 ns tPZL CL = 15 pF, S2 Open 7 15 28 ns tPZH CL = 15 pF, S1 Open 7 15 20 ns Min Typ Max Units (4) Test Conditions ns All typicals are given for VCC = 5V and TA = 25C. Driver Switching Characteristics 0C TA 70C, 4.75V < VCC < 5.25V unless otherwise specified Symbol (1) Test Conditions SINGLE ENDED CHARACTERISTICS (Figure 7, Figure 8, and Figure 10) tPLH RLDIFF = 60 9 15 22 ns tPHL CL1 = CL2 = 100 pF 9 15 22 ns 0 2 8 ns 7 15 30 ns tSKEW|tPLH-tPHL| tPLZ CL = 15 pF, S2 Open tPHZ CL = 15 pF, S1 Open 7 15 30 ns tPZL CL = 100 pF, S2 Open 30 35 50 ns tPZH CL = 100 pF, S1 Open 30 35 50 ns 6 10 18 ns DIFFERENTIAL SWITCHING CHARACTERISTICS (Figure 10) tr, tf (1) RLDIFF = 60 CL1 = CL2 = 100 pF All typicals are given for VCC = 5V and TA = 25C. Copyright (c) 1996-2013, Texas Instruments Incorporated Product Folder Links: DS3695A DS3695AT DS3696A Submit Documentation Feedback 3 DS3695A, DS3695AT, DS3696A SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 www.ti.com AC TEST CIRCUITS AND SWITCHING WAVEFORMS Figure 3. Receiver Propagation Delay Test Circuit Differential input voltage may be realized by grounding RI and pulsing RI between +2.5V and -2.5V Figure 4. Receiver Input-to-Output Propagation Delay Timing Figure 5. Receiver Enable/Disable Propagation Delay Timing Figure 6. Unless Otherwise Specified the Switches are Closed 4 Submit Documentation Feedback Copyright (c) 1996-2013, Texas Instruments Incorporated Product Folder Links: DS3695A DS3695AT DS3696A DS3695A, DS3695AT, DS3696A www.ti.com SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 Figure 7. Driver Propagation Delay Test Circuits tPLH and tPHL are measured to the respective 50% points. tSKEW is the difference between propagation delays of the complementary outputs. Figure 8. Driver Input-to-Output Propagation Delay Timing (Single-Ended) Figure 9. Driver Enable/Disable Propagation Delay Timing Figure 10. Driver Differential Transition Timing Copyright (c) 1996-2013, Texas Instruments Incorporated Product Folder Links: DS3695A DS3695AT DS3696A Submit Documentation Feedback 5 DS3695A, DS3695AT, DS3696A SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 www.ti.com Table 1. Function Tables DS3695A/DS3696A Transmitting (1) Inputs Line Outputs RE DE DI Condition DO DO TS * (DS3696A Only) X 1 1 No Fault 0 1 H X 1 0 No Fault 1 0 H X 0 X X Z Z H X 1 X Fault Z Z L Table 2. Function Tables DS3695A/DS3696A Receiving (1) Inputs (1) (1) Outputs RE DE RI-RI RO TS * (DS3696A Only) 0 0 +0.2V 1 H 0 0 -0.2V 0 H 0 0 Inputs Open** 1 H 1 0 X Z H X -- Don't care condition Z -- High impedance state Fault -- Improper line conditions causing excessive power dissipation in the driver, such as shorts or bus contention situations * TS is an "open collector" output with an on-chip 10 k pull-up resistor. ** This is a fail safe condition X -- Don't care condition Z -- High impedance state Fault -- Improper line conditions causing excessive power dissipation in the driver, such as shorts or bus contention situations * TS is an "open collector" output with an on-chip 10 k pull-up resistor. ** This is a fail safe condition Typical Application Repeater control logic not shown. Figure 11. 6 Submit Documentation Feedback Copyright (c) 1996-2013, Texas Instruments Incorporated Product Folder Links: DS3695A DS3695AT DS3696A DS3695A, DS3695AT, DS3696A www.ti.com SNLS353C - FEBRUARY 1996 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision B (April 2013) to Revision C * Page Changed layout of National Data Sheet to TI format ............................................................................................................ 6 Copyright (c) 1996-2013, Texas Instruments Incorporated Product Folder Links: DS3695A DS3695AT DS3696A Submit Documentation Feedback 7 PACKAGE OPTION ADDENDUM www.ti.com 1-Sep-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) DS3695AM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS36 95AM DS3695AMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS36 95AM DS3695ATM/NOPB OBSOLETE SOIC D 8 TBD Call TI Call TI -40 to 85 DS369 5ATM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Sep-2018 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2018 TAPE AND REEL INFORMATION *All dimensions are nominal Device DS3695AMX/NOPB Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 5.4 2.0 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2018 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS3695AMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DS3695AM DS3695AM/NOPB DS3695AMX DS3695AMX/NOPB