ATSAM3S4BA-MU - ATMEL - Datasheet.Support

This is a summary document.

The complete document is

available on the Atmel website

at www.atmel.com.

6500ES–ATARM–11-Feb-13

Description

Atmel's SAM3S series is a member of a family of 32-bit Flash microcontrollers based on the high performance ARM

Cortex-M3 processor. It operates at a maximum speed of 64 MHz and features up to 256 Kbytes of Flash and up to 48

Kbytes of SRAM. The peripheral set includes a Full Speed USB Device port with embedded transceiver, a High Speed MCI

for SDIO/SD/MMC, an External Bus Interface featuring a Static Memory Controller providing connection to SRAM,

PSRAM, NOR Flash, LCD Module and NAND Flash, 2x USARTs, 2x UARTs, 2x TWIs, 3x SPI, an I2S, as well as 1 PWM

timer, 6x general-purpose 16-bit timers, an RTC, an ADC, a 12-bit DAC and an analog comparator.

The SAM3S series is ready for capacitive touch thanks to the QTouch library, offering an easy way to implement buttons,

wheels and sliders

The SAM3S device is a medium range general purpose microcontroller with the best ratio in terms of reduced power

consumption, processing power and peripheral set. This enables the SAM3S to sustain a wide range of applications

including consumer, industrial control, and PC peripherals.

It operates from 1.62V to 3.6V and is available in 48-, 64- and 100-pin QFP, 48- and 64-pin QFN, and 100-pin BGA

packages.

The SAM3S series is the ideal migration path from the SAM7S series for applications that require more performance. The

SAM3S series is pin-to-pin compatible with the SAM7S series.

AT91SAM ARM-based Flash MCU

SAM3S

SUMMARY

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

1. Features

•Core

– ARM® Cortex®-M3 revision 2.0 running at up to 64 MHz

– Memory Protection Unit (MPU)

– Thumb®-2 instruction set

•Pin-to-pin compatible with AT91SAM7S series (48- and 64-pin versions)

•Memories

–From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory accelerator, single plane

–From 16 to 48 Kbytes embedded SRAM

–16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines

– 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support

– Memory Protection Unit (MPU)

•System

– Embedded voltage regulator for single supply operation

– Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation

– Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low power 32.768

kHz for RTC or device clock

– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. In-

application trimming access for frequency adjustment

–Slow Clock Internal RC oscillator as permanent low-power mode device clock

–Two PLLs up to 130 MHz for device clock and for USB

– Temperature Sensor

–Up to 22 peripheral DMA (PDC) channels

•Low Power Modes

– Sleep and Backup modes, down to 1.8 µA in Backup mode

– Ultra low power RTC

•Peripherals

– USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints. On-Chip Transceiver

–Up to 2 USARTs with ISO7816, IrDA®, RS-485, SPI, Manchester and Modem Mode

–Two 2-wire UARTs

–Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial Synchronous Controller (I2S), 1 High Speed Multimedia Card

Interface (SDIO/SD Card/MMC)

–Up to 6 Three-Channel 16-bit Timer/Counter with capture, waveform, compare and PWM mode. Quadrature Decoder

Logic and 2-bit Gray Up/Down Counter for Stepper Motor

–4-channel 16-bit PWM with Complementary Output, Fault Input, 12-bit Dead Time Generator Counter for Motor Control

– 32-bit Real-time Timer and RTC with calendar and alarm features

–Up to 15-channel, 1Msps ADC with differential input mode and programmable gain stage

– One 2-channel 12-bit 1Msps DAC

– One Analog Comparator with flexible input selection, Selectable input hysteresis

–32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)

– Write Protected Registers

•I/O

–Up to 79 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die

Series Resistor Termination

– Three 32-bit Parallel Input/Output Controllers, Peripheral DMA assisted Parallel Capture Mode

•Packages

– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm

– 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch 0.5 mm

– 48-lead LQFP, 7 x 7 mm, pitch 0.5 mm/48-pad QFN 7x7 mm, pitch 0.5 mm

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

1.1 Configuration Summary

The SAM3S microcontrollers differ in memory size, package and features list. Table 1-1 below summarizes the

configurations of the device family

Note: 1. Full Modem support on USART1.

Table 1-1. Configuration Summary

Device Flash SRAM

Timer

Counter

Channels GPIOs UART/

USARTs ADC

12-bit

DAC

Output External Bus

Interface HSMCI Package

SAM3S4C 256 Kbytes

single plane 48 Kbytes 6 79 2/2(1) 15 ch. 2

8-bit data,

4 chip selects,

24-bit address

1 port

4 bits

LQFP100

BGA100

SAM3S4B 256 Kbytes

single plane 48 Kbytes 3 47 2/2(1) 10 ch. 2 - 1 port

4 bits

LQFP64

QFN 64

SAM3S4A 256 Kbytes

single plane 48 Kbytes 3 34 2/1 8 ch. - - - LQFP48

QFN 48

SAM3S2C 128 Kbytes

single plane 32 Kbytes 6 79 2/2(1) 15 ch. 2

8-bit data,

4 chip selects,

24-bit address

1 port

4 bits

LQFP100

BGA100

SAM3S2B 128 Kbytes

single plane 32 Kbytes 3 47 2/2(1) 10 ch. 2 - 1 port

4 bits

LQFP64

QFN 64

SAM3S2A 128 Kbytes

single plane 32 Kbytes 3 34 2/1 8 ch. - - - LQFP48

QFN 48

SAM3S1C 64 Kbytes

single plane 16 Kbytes 6 79 2/2(1) 15 ch. 2

8-bit data,

4 chip selects,

24-bit address

1 port

4 bits

LQFP100

BGA100

SAM3S1B 64 Kbytes

single plane 16 Kbytes 3 47 2/2(1) 10 ch. 2 - 1 port

4 bits

LQFP64

QFN 64

SAM3S1A 64 Kbytes

single plane 16 Kbytes 3 34 2/1 8 ch. - - - LQFP48

QFN 48

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

2. SAM3S Block Diagram

Figure 2-1. SAM3S 100-pin Version Block Diagram

PLLA

TS T

PCK0-PCK2

System Controller

XIN

NRST

VDDCORE

XOUT

WDT

RTT

OSC 32k

XIN32

XOUT32

SUPC

RSTC

8 GPBREG

3-20 MHz

Osc.

POR

RTC

RC 32k

12/8/4 M

ERASE

TDI

TDO

TMS/SWDIO

TCK/SWCLK

JTAGSEL

I/D S

Voltage

Regulator

VDDIN

VDDOUT

SPI

TC[0..2]

DAC

ADVREF

PDC

NPCS0

PIODCCLK

PIODCEN1

PIODCEN2

NPCS1

NPCS2

NPCS3

MISO

MOSI

SPCK

MCDA[0..3]

MCCDA

MCCK

TCLK[0:2]

Temp. Sensor

PDC

TWI0 PDC

TWD0

PWM

PDC

DDP

DDM

MPU

24-Bit

SysTick Counter

4-layer AHB Bus Matrix Fmax 64 MHz

TWI1 PDC

TWCK1

TWD1

PWMH[0:3]

PWML[0:3]

PWMFI0

PDC

UART0

UART1

URXD0

UTXD0

URXD1

UTXD1

SSC

Peripheral

Bridge

PDC

PIO

PDC

2668

Bytes

FIFO

USB 2.0

Full

Speed

VDDPLL

VDDIO

PDC

RXD0

TXD0

USART0

SCK0

RTS0

CTS0

Analog

Comparator

CRC Unit

ADC

Transceiver

PLLB

In-Circuit Emulator

JTAG & Serial Wire

Flash

Unique

Identifier

PMC

PIOA / PIOB / PIOC

ADTRG

Cortex-M3 Processor

Fmax 64 MHz

Timer Counter A

Timer Counter B

TWCK0

FLASH

256 KBytes

128 KBytes

64 KBytes

SRAM

48 KBytes

32 KBytes

16 KBytes

ROM

16 KBytes

PIO

External Bus

Interface

D[7:0]

PIODC[7:0]

A[0:23]

A21/NANDALE

A22/NANDCLE

NCS0

NCS1

NCS2

NCS3

NRD

NWE

NANDOE

NANDWE

NWAIT

High Speed MCI

PDC

DATRG

PDC

DAC0

DAC1

TC[3..5]

TIOA[3:5]

TIOB[3:5]

TIOA[0:2]

TIOB[0:2]

TCLK[3:5]

AD[0..14]

PDC

RXD1

TXD1

USART1

SCK1

RTS 1

CTS1

DSR1

DTR1

RI1

DCD1

NAND Flash

Logic

Static Memory

Controller

ADC

DAC

Temp Sensor

ADVREF

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 2-2. SAM3S 64-pin Version Block Diagram

TDI

TDO

TMS/SWDIO

TCK/SWCLK

JTAGSEL

I/D S

Voltage

Regulator

VDDIN

VDDOUT

SPI

TC[0..2]

ADVREF

TIOB[0:2]

TIOA[0:2]

TCLK[0:2]

PDC

TWI0 PDC

TWCK0

PWM

PDC

DDP

DDM

Transceiver

MPU

TWI1 PD C

TWD1

PWMH[0:3]

PWMFI0

PDC

UART0

UART1

URXD0

UTXD0

URXD1

UTXD1

SSC

Peripheral

Bridge

PDC

2668

Bytes

FIFO

USB 2.0

Full

Speed

PDC

RXD0

TXD0

USART0

SCK0

RTS0

CTS0

PLLA

TS T

PCK0-PCK2

System Controller

XIN

NRST

VDDCORE

XOUT

WDT

RTT

OSC 32K

XIN32

XOUT32

SUPC

RSTC

8 GPBREG

3-20 MHz

Osc.

POR

RTC

RC 32k

12/8/4 M

ERASE

VDDPLL

VDDIO

PLLB

PMC

PIOA / PIOB

JTAG & Serial Wire

Flash

Unique

Identifier

PIODCCLK

PIODCEN1

PIODCEN2

PIO

PDC

PIODC[7:0]

Analog

Comparator

CRC Unit

ADC

DAC

Temp Sensor

ADVREF

NPCS0

NPCS1

NPCS2

NPCS3

MISO

MOSI

SPCK

MCCK

MCCDA

MCDA[0..3]

High Speed MCI

Cortex-M3 Processor

Fmax 64 MHz

In-Circuit Emulator

Timer Counter A

ROM

16 KBytes

TWD0

TWCK1

PWML[0:3]

24-Bit

SysTick Counter FLASH

256 KBytes

128 KBytes

64 KBytes

SRAM

48 KBytes

32 KBytes

16 KBytes

PDC

DAC1

DAC0

AD[0..9]

ADTRG

DATRG

PDC

RXD1

TXD1

USART1

SCK1

RTS1

CTS1

DSR1

DTR1

RI1

DCD1

4-layer AHB Bus Matrix Fmax 64 MHz

DAC

PDC

Temp. Sensor

ADC

PDC

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 2-3. SAM3S 48-pin Version Block Diagram

TDI

TDO

TMS/SWDIO

TCK/SWCLK

JTAGSEL

I/D S

Voltage

Regulator

VDDIN

VDDOUT

SPI

TC[0..2]

ADVREF

TIOA[0:2]

TIOB[0:2]

TCLK[0:2]

PDC

TWI0 PDC

TWCK0

TWD0

PWM

PDC

DDP

DDM

Transceiver

MPU

TWI1 PDC

TWCK1

TWD1

PWMH[0:3]

PWML[0:3]

PWMFI0

PDC

UART0

UART1

URXD0

UTXD0

URXD1

UTXD1

SSC

Peripheral

Bridge

PDC

2668

Bytes

FIFO

USB 2.0

Full

Speed

PDC

RXD0

TXD0

USART0

SCK0

RTS0

CTS0

PLLA

System Controller

WDT

RTT

OSC32K

SUPC

RSTC

8 GPBREG

3-20 MHz

Osc.

POR

RTC

RC 32k

12/8/4 M

PLLB

PMC

PIOA / PIOB

JTAG & Serial Wire

Flash

Unique

Identifier

Analog

Comparator

CRC Unit

ADC

Temp Sensor

ADVREF

NPCS0

NPCS1

NPCS2

NPCS3

MISO

MOSI

SPCK

Cortex-M3 Processor

Fmax 64 MHz

Timer Counter A

ROM

16 KBytes

TST

XIN

XOUT

XIN32

XOUT32

ERASE

VDDIO

VDDCORE

VDDPLL

PCK0-PCK2

In-Circuit Emulator

24-Bit

SysTick Counter FLASH

256 KBytes

128 KBytes

64 KBytes

SRAM

48 KBytes

32 KBytes

16 KBytes

AD[0..7]

ADTRG

4-layer AHB Bus Matrix Fmax 64 MHz

PDC

Temp. Sensor

ADC

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

3. Signal Description

Table 3-1 gives details on the signal names classified by peripheral.

Table 3-1. Signal Description List

Signal Name Function Type Active

Level Voltage

reference Comments

Power Supplies

VDDIO Peripherals I/O Lines and USB transceiver

Power Supply Power 1.62V to 3.6V

VDDIN Voltage Regulator Input, ADC, DAC and

Analog Comparator Power Supply Power 1.8V to 3.6V(4)

VDDOUT Voltage Regulator Output Power 1.8V Output

VDDPLL Oscillator and PLL Power Supply Power 1.62 V to 1.95V

VDDCORE Power the core, the embedded memories

and the peripherals Power 1.62V to 1.95V

GND Ground Ground

Clocks, Oscillators and PLLs

XIN Main Oscillator Input Input

VDDIO

Reset State:

- PIO Input

- Internal Pull-up disabled

- Schmitt Trigger enabled(1)

XOUT Main Oscillator Output Output

XIN32 Slow Clock Oscillator Input Input

XOUT32 Slow Clock Oscillator Output Output

PCK0 - PCK2 Programmable Clock Output Output

Reset State:

- PIO Input

- Internal Pull-up enabled

- Schmitt Trigger enabled(1)

Serial Wire/JTAG Debug Port - SWJ-DP

TCK/SWCLK Test Clock/Serial Wire Clock Input

VDDIO

Reset State:

- SWJ-DP Mode

- Internal pull-up disabled(5)

- Schmitt Trigger enabled(1)

TDI Test Data In Input

TDO/TRACESWO Test Data Out / Trace Asynchronous Data

Out Output

TMS/SWDIO Test Mode Select /Serial Wire Input/Output Input / I/O

JTAGSEL JTAG Selection Input High Permanent Internal

pull-down

Flash Memory

ERASE Flash and NVM Configuration Bits Erase

Command Input High VDDIO

Reset State:

- Erase Input

- Internal pull-down enabled

- Schmitt Trigger enabled(1)

Reset/Test

NRST Synchronous Microcontroller Reset I/O Low VDDIO

Permanent Internal

pull-up

TST Test Select Input Permanent Internal

pull-down

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Universal Asynchronous Receiver Transmitter - UARTx

URXDx UART Receive Data Input

UTXDx UART Transmit Data Output

PIO Controller - PIOA - PIOB - PIOC

PA0 - PA31 Parallel IO Controller A I/O

VDDIO

Reset State:

- PIO or System IOs(2)

- Internal pull-up enabled

- Schmitt Trigger enabled(1)

PB0 - PB14 Parallel IO Controller B I/O

PC0 - PC31 Parallel IO Controller C I/O

PIO Controller - Parallel Capture Mode (PIOA Only)

PIODC0-PIODC7 Parallel Capture Mode Data Input

VDDIOPIODCCLK Parallel Capture Mode Clock Input

PIODCEN1-2 Parallel Capture Mode Enable Input

External Bus Interface

D0 - D7 Data Bus I/O

A0 - A23 Address Bus Output

NWAIT External Wait Signal Input Low

Static Memory Controller - SMC

NCS0 - NCS3 Chip Select Lines Output Low

NRD Read Signal Output Low

NWE Write Enable Output Low

NAND Flash Logic

NANDOE NAND Flash Output Enable Output Low

NANDWE NAND Flash Write Enable Output Low

High Speed Multimedia Card Interface - HSMCI

MCCK Multimedia Card Clock I/O

MCCDA Multimedia Card Slot A Command I/O

MCDA0 - MCDA3 Multimedia Card Slot A Data I/O

Universal Synchronous Asynchronous Receiver Transmitter USARTx

SCKx USARTx Serial Clock I/O

TXDx USARTx Transmit Data I/O

RXDx USARTx Receive Data Input

RTSx USARTx Request To Send Output

CTSx USARTx Clear To Send Input

DTR1 USART1 Data Terminal Ready I/O

DSR1 USART1 Data Set Ready Input

DCD1 USART1 Data Carrier Detect Input

RI1 USART1 Ring Indicator Input

Table 3-1. Signal Description List (Continued)

Signal Name Function Type Active

Level Voltage

reference Comments

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Synchronous Serial Controller - SSC

TD SSC Transmit Data Output

RD SSC Receive Data Input

TK SSC Transmit Clock I/O

RK SSC Receive Clock I/O

TF SSC Transmit Frame Sync I/O

RF SSC Receive Frame Sync I/O

Timer/Counter - TC

TCLKx TC Channel x External Clock Input Input

TIOAx TC Channel x I/O Line A I/O

TIOBx TC Channel x I/O Line B I/O

Pulse Width Modulation Controller- PWMC

PWMHx PWM Waveform Output High for channel x Output

PWMLx PWM Waveform Output Low for channel x Output

only output in

complementary mode when

dead time insertion is

enabled

PWMFI0 PWM Fault Input Input

Serial Peripheral Interface - SPI

MISO Master In Slave Out I/O

MOSI Master Out Slave In I/O

SPCK SPI Serial Clock I/O

SPI_NPCS0 SPI Peripheral Chip Select 0 I/O Low

SPI_NPCS1 -

SPI_NPCS3 SPI Peripheral Chip Select Output Low

Two-Wire Interface- TWI

TWDx TWIx Two-wire Serial Data I/O

TWCKx TWIx Two-wire Serial Clock I/O

Analog

ADVREF ADC, DAC and Analog Comparator

Reference Analog

Analog-to-Digital Converter - ADC

AD0 - AD14 Analog Inputs Analog,

Digital

ADTRG ADC Trigger Input VDDIO

12-bit Digital-to-Analog Converter - DAC

DAC0 - DAC1 Analog output Analog,

Digital

DACTRG DAC Trigger Input VDDIO

Table 3-1. Signal Description List (Continued)

Signal Name Function Type Active

Level Voltage

reference Comments

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Notes: 1. Schmitt Triggers can be disabled through PIO registers.

2. Some PIO lines are shared with System IOs.

3. Refer to the USB sub section in the product Electrical Characteristics Section for Pull-down value in USB Mode.

4. See Section 5.3 “Typical Powering Schematics” for restriction on voltage range of Analog Cells.

5. TDO pin is set in input mode when the Cortex-M3 Core is not in debug mode. Thus the internal pull-up corresponding

to this PIO line must be enabled to avoid current consumption due to floating input.

Fast Flash Programming Interface - FFPI

PGMEN0-PGMEN2 Programming Enabling Input VDDIO

PGMM0-PGMM3 Programming Mode Input

VDDIO

PGMD0-PGMD15 Programming Data I/O

PGMRDY Programming Ready Output High

PGMNVALID Data Direction Output Low

PGMNOE Programming Read Input Low

PGMCK Programming Clock Input

PGMNCMD Programming Command Input Low

USB Full Speed Device

DDM USB Full Speed Data -

Analog,

Digital VDDIO

Reset State:

- USB Mode

- Internal Pull-down(3)

DDP USB Full Speed Data +

Table 3-1. Signal Description List (Continued)

Signal Name Function Type Active

Level Voltage

reference Comments

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4. Package and Pinout

4.1 SAM3S4/2/1C Package and Pinout

Figure 4-2 shows the orientation of the 100-ball TFBGA Package

4.1.1 100-lead LQFP Package Outline

Figure 4-1. Orientation of the 100-lead LQFP Package

4.1.2 100-ball TFBGA Package Outline

The 100-Ball TFBGA package has a 0.8 mm ball pitch and respects Green Standards. Its dimensions are 9 x 9 x 1.1 mm.

Figure 4-2. Orientation of the 100-BALL TFBGA Package

125

5175

100

ABCDEFGHJK

TOP VIEW

BALL A1

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4.1.3 100-Lead LQFP Pinout

Table 4-1. 100-lead LQFP SAM3S4/2/1C Pinout

1 ADVREF 26 GND 51 TDI/PB4 76 TDO/TRACESWO/PB

2 GND 27 VDDIO 52 PA6/PGMNOE 77 JTAGSEL

3 PB0/AD4 28 PA16/PGMD4 53 PA5/PGMRDY 78 PC18

4 PC29/AD13 29 PC7 54 PC28 79 TMS/SWDIO/PB6

5 PB1/AD5 30 PA15/PGMD3 55 PA4/PGMNCMD 80 PC19

6 PC30/AD14 31 PA14/PGMD2 56 VDDCORE 81 PA31

7 PB2/AD6 32 PC6 57 PA27/PGMD15 82 PC20

8 PC31 33 PA13/PGMD1 58 PC8 83 TCK/SWCLK/PB7

9 PB3/AD7 34 PA24/PGMD12 59 PA28 84 PC21

10 VDDIN 35 PC5 60 NRST 85 VDDCORE

11 VDDOUT 36 VDDCORE 61 TST 86 PC22

12 PA17/PGMD5/AD0 37 PC4 62 PC9 87 ERASE/PB12

13 PC26 38 PA25/PGMD13 63 PA29 88 DDM/PB10

14 PA18/PGMD6/AD1 39 PA26/PGMD14 64 PA30 89 DDP/PB11

15 PA21/PGMD9/AD8 40 PC3 65 PC10 90 PC23

16 VDDCORE 41 PA12/PGMD0 66 PA3 91 VDDIO

17 PC27 42 PA11/PGMM3 67 PA2/PGMEN2 92 PC24

18 PA19/PGMD7/AD2 43 PC2 68 PC11 93 PB13/DAC0

19 PC15/AD11 44 PA10/PGMM2 69 VDDIO 94 PC25

20 PA22/PGMD10/AD9 45 GND 70 GND 95 GND

21 PC13/AD10 46 PA9/PGMM1 71 PC14 96 PB8/XOUT

22 PA23/PGMD11 47 PC1 72 PA1/PGMEN1 97 PB9/PGMCK/XIN

23 PC12/AD12 48 PA8/XOUT32/

PGMM0 73 PC16 98 VDDIO

24 PA20/PGMD8/AD3 49 PA7/XIN32/

PGMNVALID 74 PA0/PGMEN0 99 PB14/DAC1

25 PC0 50 VDDIO 75 PC17 100 VDDPLL

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4.1.4 100-ball TFBGA Pinout

Table 4-2. 100-ball TFBGA SAM3S4/2/1C Pinout

A1 PB1/AD5 C6 TCK/SWCLK/PB7 F1 PA18/PGMD6/AD1 H6 PC4

A2 PC29 C7 PC16 F2 PC26 H7 PA11/PGMM3

A3 VDDIO C8 PA1/PGMEN1 F3 VDDOUT H8 PC1

A4 PB9/PGMCK/XIN C9 PC17 F4 GND H9 PA6/PGMNOE

A5 PB8/XOUT C10 PA0/PGMEN0 F5 VDDIO H10 TDI/PB4

A6 PB13/DAC0 D1 PB3/AD7 F6 PA27/PGMD15 J1 PC15/AD11

A7 DDP/PB11 D2 PB0/AD4 F7 PC8 J2 PC0

A8 DDM/PB10 D3 PC24 F8 PA28 J3 PA16/PGMD4

A9 TMS/SWDIO/PB6 D4 PC22 F9 TST J4 PC6

A10 JTAGSEL D5 GND F10 PC9 J5 PA24/PGMD12

B1 PC30 D6 GND G1 PA21/PGMD9/AD8 J6 PA25/PGMD13

B2 ADVREF D7 VDDCORE G2 PC27 J7 PA10/PGMM2

B3 GNDANA D8 PA2/PGMEN2 G3 PA15/PGMD3 J8 GND

B4 PB14/DAC1 D9 PC11 G4 VDDCORE J9 VDDCORE

B5 PC21 D10 PC14 G5 VDDCORE J10 VDDIO

B6 PC20 E1 PA17/PGMD5/AD0 G6 PA26/PGMD14 K1 PA22/PGMD10/AD9

B7 PA31 E2 PC31 G7 PA12/PGMD0 K2 PC13/AD10

B8 PC19 E3 VDDIN G8 PC28 K3 PC12/AD12

B9 PC18 E4 GND G9 PA4/PGMNCMD K4 PA20/PGMD8/AD3

B10 TDO/TRACESWO/

PB5 E5 GND G10 PA5/PGMRDY K5 PC5

C1 PB2/AD6 E6 NRST H1 PA19/PGMD7/AD2 K6 PC3

C2 VDDPLL E7 PA29/AD13 H2 PA23/PGMD11 K7 PC2

C3 PC25 E8 PA30/AD14 H3 PC7 K8 PA9/PGMM1

C4 PC23 E9 PC10 H4 PA14/PGMD2 K9 PA8/XOUT32/PGMM0

C5 ERASE/PB12 E10 PA3 H5 PA13/PGMD1 K10 PA7/XIN32/

PGMNVALID

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4.2 SAM3S4/2/1B Package and Pinout

Figure 4-3. Orientation of the 64-pad QFN Package

Figure 4-4. Orientation of the 64-lead LQFP Package

17 32

4964

TOP VIEW

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4.2.1 64-Lead LQFP and QFN Pinout

64-pin version SAM3S devices are pin-to-pin compatible with AT91SAM7S legacy products. Furthermore, SAM3S

products have new functionalities shown in italic in Table 4-3.

Note: The bottom pad of the QFN package must be connected to ground.

Table 4-3. 64-pin SAM3S4/2/1B Pinout

1 ADVREF 17 GND 33 TDI/PB4 49 TDO/TRACESWO/PB5

2 GND 18 VDDIO 34 PA6/PGMNOE 50 JTAGSEL

3 PB0/AD4 19 PA16/PGMD4 35 PA5/PGMRDY 51 TMS/SWDIO/PB6

4 PB1/AD5 20 PA15/PGMD3 36 PA4/PGMNCMD 52 PA31

5 PB2/AD6 21 PA14/PGMD2 37 PA27/PGMD15 53 TCK/SWCLK/PB7

6 PB3/AD7 22 PA13/PGMD1 38 PA28 54 VDDCORE

7 VDDIN 23 PA24/PGMD12 39 NRST 55 ERASE/PB12

8 VDDOUT 24 VDDCORE 40 TST 56 DDM/PB10

9PA17/PGMD5/

AD025 PA25/PGMD13 41 PA29 57 DDP/PB11

10 PA18/PGMD6/

AD1 26 PA26/PGMD14 42 PA30 58 VDDIO

11 PA21/PGMD9/

AD8 27 PA12/PGMD0 43 PA3 59 PB13/DAC0

12 VDDCORE 28 PA11/PGMM3 44 PA2/PGMEN2 60 GND

13 PA19/PGMD7/

AD2 29 PA10/PGMM2 45 VDDIO 61 XOUT/PB8

14 PA22/PGMD10/

AD9 30 PA9/PGMM1 46 GND 62 XIN/PGMCK/PB9

15 PA23/PGMD11 31 PA8/XOUT32/

PGMM0 47 PA1/PGMEN1 63 PB14/DAC1

16 PA20/PGMD8/

AD3 32 PA7/XIN32/

PGMNVALID 48 PA0/PGMEN0 64 VDDPLL

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4.3 SAM3S4/2/1A Package and Pinout

Figure 4-5. Orientation of the 48-pad QFN Package

Figure 4-6. Orientation of the 48-lead LQFP Package

13 24

3748

TOP VIEW

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

4.3.1 48-Lead LQFP and QFN Pinout

Note: The bottom pad of the QFN package must be connected to ground.

Table 4-4. 48-pin SAM3S4/2/1A Pinout

1 ADVREF 13 VDDIO 25 TDI/PB4 37 TDO/TRACESWO/

PB5

2 GND 14 PA16/PGMD4 26 PA6/PGMNOE 38 JTAGSEL

3 PB0/AD4 15 PA15/PGMD3 27 PA5/PGMRDY 39 TMS/SWDIO/PB6

4 PB1/AD5 16 PA14/PGMD2 28 PA4/PGMNCMD 40 TCK/SWCLK/PB7

5 PB2/AD6 17 PA13/PGMD1 29 NRST 41 VDDCORE

6 PB3/AD7 18 VDDCORE 30 TST 42 ERASE/PB12

7 VDDIN 19 PA12/PGMD0 31 PA3 43 DDM/PB10

8 VDDOUT 20 PA11/PGMM3 32 PA2/PGMEN2 44 DDP/PB11

9PA17/PGMD5/

AD0 21 PA10/PGMM2 33 VDDIO 45 XOUT/PB8

10 PA18/PGMD6/

AD1 22 PA9/PGMM1 34 GND 46 XIN/PB9/PGMCK

11 PA19/PGMD7/

AD2 23 PA8/XOUT32/

PGMM0 35 PA1/PGMEN1 47 VDDIO

12 PA20/AD3 24 PA7/XIN32/

PGMNVALID 36 PA0/PGMEN0 48 VDDPLL

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

5. Power Considerations

5.1 Power Supplies

The SAM3S product has several types of power supply pins:

zVDDCORE pins: Power the core, the embedded memories and the peripherals; voltage ranges from 1.62V and

1.95V.

zVDDIO pins: Power the Peripherals I/O lines (Input/Output Buffers); USB transceiver; Backup part, 32kHz crystal

oscillator and oscillator pads; ranges from 1.62V and 3.6V

zVDDIN pin: Voltage Regulator Input, ADC, DAC and Analog Comparator Power Supply; Voltage ranges from 1.8V

to 3.6V

zVDDPLL pin: Powers the PLLA, PLLB, the Fast RC and the 3 to 20 MHz oscillator; voltage ranges from 1.62V and

1.95V.

5.2 Voltage Regulator

The SAM3S embeds a voltage regulator that is managed by the Supply Controller.

This internal regulator is intended to supply the internal core of SAM3S. It features two different operating modes:

zIn Normal mode, the voltage regulator consumes less than 700 μA static current and draws 80 mA of output

current. Internal adaptive biasing adjusts the regulator quiescent current depending on the required load current.

In Wait Mode quiescent current is only 7 μA.

• In Backup mode, the voltage regulator consumes less than 1 μA while its output (VDDOUT) is driven internally to GND.

The default output voltage is 1.80V and the start-up time to reach Normal mode is inferior to 100 μs.

For adequate input and output power supply decoupling/bypassing, refer to the Voltage Regulator section in the

Electrical Characteristics section of the datasheet.

5.3 Typical Powering Schematics

The SAM3S supports a 1.62V-3.6V single supply mode. The internal regulator input connected to the source and its

output feeds VDDCORE. Figure 5-1 shows the power schematics.

As VDDIN powers the voltage regulator, the ADC/DAC and the analog comparator, when the user does not want to use

the embedded voltage regulator, it can be disabled by software via the SUPC (note that it is different from Backup mode).

Figure 5-1. Single Supply

Note: For USB, VDDIO needs to be greater than 3.0V.

For ADC, VDDIN needs to be greater than 2.0V.

For DAC, VDDIN needs to be greater than 2.4V.

Main Supply

(1.8V-3.6V) ADC, DAC

Analog Comp.

USB

Transceivers.

VDDIN

Voltage

Regulator

VDDOUT

VDDCORE

VDDIO

VDDPLL

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 5-2. Core Externally Supplied

Note: For USB, VDDIO needs to be greater than 3.0V.

For ADC, VDDIN needs to be greater than 2.0V

For DAC, VDDIN needs to be greater than 2.4V.

Figure 5-3 below provides an example of the powering scheme when using a backup battery. Since the PIO state is

preserved when in backup mode, any free PIO line can be used to switch off the external regulator by driving the PIO line

at low level (PIO is input, pull-up enabled after backup reset). External wake-up of the system can be from a push button

or any signal. See Section 5.6 “Wake-up Sources” for further details.

Figure 5-3. Backup Battery

Main Supply

(1.62V-3.6V)

Can be the

same supply

VDDCORE Supply

(1.62V-1.95V)

ADC, DAC, Analog

Comparator Supply

(2.0V-3.6V)

ADC, DAC

Analog Comp.

USB

Transceivers.

VDDIN

Voltage

Regulator

VDDOUT

VDDCORE

VDDIO

VDDPLL

ADC, DAC

Analog Comp.

USB

Transceivers.

VDDIN

Voltage

Regulator

3.3V

LDO

Backup

Battery

ON/OFF

IN OUT VDDOUT

Main Supply

VDDCORE

ADC, DAC, Analog

Comparator Supply

(2.0V-3.6V)

VDDIO

VDDPLL

PIOx (Output)

WAKEUPx

External wakeup signal

Note: The two diodes provide a “switchover circuit” (for illustration purpose)

between the backup battery and the main supply when the system is put in

backup mode.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

5.4 Active Mode

Active mode is the normal running mode with the core clock running from the fast RC oscillator, the main crystal oscillator

or the PLLA. The power management controller can be used to adapt the frequency and to disable the peripheral clocks.

5.5 Low Power Modes

The various low power modes of the SAM3S are described below:

5.5.1 Backup Mode

The purpose of backup mode is to achieve the lowest power consumption possible in a system which is performing

periodic wake-ups to perform tasks but not requiring fast startup time (<0.1ms). Total current consumption is 3 μA typical.

The Supply Controller, zero-power power-on reset, RTT, RTC, Backup registers and 32 kHz oscillator (RC or crystal

oscillator selected by software in the Supply Controller) are running. The regulator and the core supply are off.

Backup mode is based on the Cortex-M3 deepsleep mode with the voltage regulator disabled.

The SAM3S can be awakened from this mode through WUP0-15 pins, the supply monitor (SM), the RTT or RTC wake-

up event.

Backup mode is entered by using WFE instructions with the SLEEPDEEP bit in the System Control Register of the

Cortex-M3 set to 1. (See the Power management description in The ARM Cortex M3 Processor section of the

product datasheet).

Exit from Backup mode happens if one of the following enable wake up events occurs:

• WKUPEN0-15 pins (level transition, configurable debouncing)

• Supply Monitor alarm

• RTC alarm

• RTT alarm

5.5.2 Wait Mode

The purpose of the wait mode is to achieve very low power consumption while maintaining the whole device in a

powered state for a startup time of less than 10 µs. Current Consumption in Wait mode is typically 15 µA (total cur-

rent consumption) if the internal voltage regulator is used or 8 µA if an external regulator is used.

In this mode, the clocks of the core, peripherals and memories are stopped. However, the core, peripherals and

memories power supplies are still powered. From this mode, a fast start up is available.

This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in PMC_FSMR).

The Cortex-M3 is able to handle external events or internal events in order to wake-up the core (WFE). This is

done by configuring the external lines WUP0-15 as fast startup wake-up pins (refer to Section 5.7 “Fast Startup”).

RTC or RTT Alarm and USB wake-up events can be used to wake up the CPU (exit from WFE).

Entering Wait Mode:

• Select the 4/8/12 MHz fast RC oscillator as Main Clock

• Set the LPM bit in the PMC Fast Startup Mode Register (PMC_FSMR)

• Execute the Wait-For-Event (WFE) instruction of the processor

Note: Internal Main clock resynchronization cycles are necessary between the writing of MOSCRCEN bit and the

effective entry in Wait mode. Depending on the user application, Waiting for MOSCRCEN bit to be cleared is

recommended to ensure that the core will not execute undesired instructions.

The bit MOSCRCEN should be automatically set to '0'. So you have to add after this instruction the following: while

(MOSCRCEN ==0); so that you are sure to stay in the loop until you awake from the wait mode. In that case you are sure

the core will not continue to fetch the code but once you have exited the wait mode (in that case MOSCRCEN will be

automatically set to '1').

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

5.5.3 Sleep Mode

The purpose of sleep mode is to optimize power consumption of the device versus response time. In this mode,

only the core clock is stopped. The peripheral clocks can be enabled. The current consumption in this mode is

application dependent.

This mode is entered via Wait for Interrupt (WFI) or Wait for Event (WFE) instructions with LPM = 0 in PMC_FSMR.

The processor can be woke up from an interrupt if WFI instruction of the Cortex M3 is used, or from an event if the

WFE instruction is used to enter this mode.

5.5.4 Low Power Mode Summary Table

The modes detailed above are the main low power modes. Each part can be set to on or off separately and wake

up sources can be individually configured. Table 5-1 below shows a summary of the configurations of the low

power modes.

Notes: 1. When considering wake-up time, the time required to start the PLL is not taken into account. Once started, the device

works with the 4/8/12 MHz fast RC oscillator. The user has to add the PLL start-up time if it is needed in the system.

The wake-up time is defined as the time taken for wake up until the first instruction is fetched.

2. The external loads on PIOs are not taken into account in the calculation.

3. Supply Monitor current consumption is not included.

4. Total Current consumption.

5. 5 μA on VDDCORE, 15 μA for total current consumption (using internal voltage regulator), 8 μA for total current con-

sumption (without using internal voltage regulator).

6. Depends on MCK frequency.

7. In this mode the core is supplied and not clocked but some peripherals can be clocked.

Table 5-1. Low Power Mode Configuration Summary

Mode

SUPC,

32 kHz

Oscillator

RTC RTT

Backup

Registers,

POR

(Backup

Region) Regulator

Core

Memory

Peripherals Mode Entry Potential Wake Up

Sources Core at

Wake Up

PIO State

while in Low

Power Mode PIO State at

Wake Up

Consumption

(2)

(3) Wake-up

Time(1)

Backup

Mode ON OFF OFF

(Not powered)

WFE

+SLEEPDEEP

bit = 1

WUP0-15 pins

SM alarm

RTC alarm

RTT alarm

Reset Previous

state saved

PIOA &

PIOB &

PIOC

Inputs with

pull ups

3 μA typ(4) < 0.1 ms

Wait

Mode ON ON Powered

(Not clocked)

WFE

+SLEEPDEEP

bit = 0

+LPM bit = 1

Any Event from:

Fast startup through

WUP0-15 pins

RTC alarm

RTT alarm

USB wake-up

Clocked

back

state saved Unchanged 5 μA/15 μA (5) < 10 μs

Sleep

Mode ON ON Powered(7)

(Not clocked)

WFE or WFI

+SLEEPDEEP

bit = 0

+LPM bit = 0

Entry mode =WFI

Interrupt Only; Entry

mode =WFE Any

Enabled Interrupt

and/or Any Event

from: Fast start-up

through WUP0-15

pins

RTC alarm

RTT alarm

USB wake-up

Clocked

back

state saved Unchanged (6) (6)

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

5.6 Wake-up Sources

The wake-up events allow the device to exit the backup mode. When a wake-up event is detected, the Supply Controller

performs a sequence which automatically reenables the core power supply and the SRAM power supply, if they are not

already enabled.

Figure 5-4. Wake-up Source

WKUP15

WKUPEN15

WKUPT15

WKUPEN1

WKUPEN0

Debouncer

SLCK

WKUPDBC

WKUPS

RTCEN

rtc_alarm

SMEN

sm_out

Core

Supply

Restart

WKUPIS0

WKUPIS1

WKUPIS15

Falling/Rising

Edge

Detector

WKUPT0

Falling/Rising

Edge

Detector

WKUPT1

Falling/Rising

Edge

Detector

WKUP0

WKUP1

RTTEN

rtt_alarm

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

5.7 Fast Startup

The device allows the processor to restart in a few microseconds while the processor is in wait mode. A fast start up can

occur upon detection of a low level on one of the 19 wake-up inputs (WKUP0 to 15 + SM + RTC + RTT).

The fast restart circuitry, as shown in Figure 5-5, is fully asynchronous and provides a fast start-up signal to the Power

Management Controller. As soon as the fast start-up signal is asserted, the PMC automatically restarts the embedded

4/8/12 MHz fast RC oscillator, switches the master clock on this 4MHz clock and reenables the processor clock.

Figure 5-5. Fast Start-Up Circuitry

fast_restart

WKUP15

FSTT15

FSTP15

WKUP1

FSTT1

FSTP1

WKUP0

FSTT0

FSTP0

RTTAL

RTCAL

USBAL

RTT Alarm

RTC Alarm

USB Alarm

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

6. Input/Output Lines

The SAM3S has several kinds of input/output (I/O) lines such as general purpose I/Os (GPIO) and system I/Os. GPIOs

can have alternate functionality due to multiplexing capabilities of the PIO controllers. The same PIO line can be used

whether in IO mode or by the multiplexed peripheral. System I/Os include pins such as test pins, oscillators, erase or

analog inputs.

6.1 General Purpose I/O Lines

GPIO Lines are managed by PIO Controllers. All I/Os have several input or output modes such as pull-up or pull-down,

input Schmitt triggers, multi-drive (open-drain), glitch filters, debouncing or input change interrupt. Programming of these

modes is performed independently for each I/O line through the PIO controller user interface. For more details, refer to

the product PIO controller section.

The input output buffers of the PIO lines are supplied through VDDIO power supply rail.

The SAM3S embeds high speed pads able to handle up to 32 MHz for HSMCI (MCK/2), 45 MHz for SPI clock lines and

35 MHz on other lines. See AC Characteristics Section in the Electrical Characteristics Section of the datasheet for more

details. Typical pull-up and pull-down value is 100 kΩ for all I/Os.

Each I/O line also embeds an ODT (On-Die Termination), see Figure 6-1. It consists of an internal series resistor

termination scheme for impedance matching between the driver output (SAM3S) and the PCB trace impedance

preventing signal reflection. The series resistor helps to reduce IOs switching current (di/dt) thereby reducing in turn,

EMI. It also decreases overshoot and undershoot (ringing) due to inductance of interconnect between devices or

between boards. In conclusion ODT helps diminish signal integrity issues.

Figure 6-1. On-Die Termination

6.2 System I/O Lines

System I/O lines are pins used by oscillators, test mode, reset and JTAG to name but a few. Described below are the

SAM3S system I/O lines shared with PIO lines:

These pins are software configurable as general purpose I/O or system pins. At startup the default function of these pins

is always used.

PCB Trace

Z0 ~ 50 Ohms

Receiver

SAM3 Driver with

Rodt

Zout ~ 10 Ohms

Z0 ~ Zout + Rodt

ODT

36 Ohms Typ.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Notes: 1. If PB12 is used as PIO input in user applications, a low level must be ensured at startup to prevent Flash erase before

the user application sets PB12 into PIO mode,

2. In the product Datasheet Refer to: Slow Clock Generator of the Supply Controller section.

3. In the product Datasheet Refer to: 3 to 20 MHZ Crystal Oscillator information in PMC section.

6.2.1 Serial Wire JTAG Debug Port (SWJ-DP) Pins

The SWJ-DP pins are TCK/SWCLK, TMS/SWDIO, TDO/SWO, TDI and commonly provided on a standard 20-pin JTAG

connector defined by ARM. For more details about voltage reference and reset state, refer to Table 3-1 on page 7.

At startup, SWJ-DP pins are configured in SWJ-DP mode to allow connection with debugging probe. Please refer to the

Debug and Test Section of the product datasheet.

SWJ-DP pins can be used as standard I/Os to provide users more general input/output pins when the debug port is not

needed in the end application. Mode selection between SWJ-DP mode (System IO mode) and general IO mode is

performed through the AHB Matrix Special Function Registers (MATRIX_SFR). Configuration of the pad for pull-up,

triggers, debouncing and glitch filters is possible regardless of the mode.

The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. It integrates a permanent

pull-down resistor of about 15 kΩ to GND, so that it can be left unconnected for normal operations.

By default, the JTAG Debug Port is active. If the debugger host wants to switch to the Serial Wire Debug Port, it must

provide a dedicated JTAG sequence on TMS/SWDIO and TCK/SWCLK which disables the JTAG-DP and enables the

SW-DP. When the Serial Wire Debug Port is active, TDO/TRACESWO can be used for trace.

The asynchronous TRACE output (TRACESWO) is multiplexed with TDO. So the asynchronous trace can only be used

with SW-DP, not JTAG-DP. For more information about SW-DP and JTAG-DP switching, please refer to the Debug and

Test Section.

6.3 Test Pin

The TST pin is used for JTAG Boundary Scan Manufacturing Test or Fast Flash programming mode of the SAM3S

series. The TST pin integrates a permanent pull-down resistor of about 15 kΩ to GND, so that it can be left uncon-

nected for normal operations. To enter fast programming mode, see the Fast Flash Programming Interface (FFPI)

section. For more on the manufacturing and test mode, refer to the “Debug and Test” section of the product

datasheet.

Table 6-1. System I/O Configuration List

SYSTEM_IO

bit number Default function

after reset Other function Constraints for

normal start Configuration

12 ERASE PB12 Low Level at

startup(1)

In Matrix User Interface Registers

(Refer to the SystemIO

Configuration Register in the Bus

Matrix section of the product

datasheet.)

10 DDM PB10 -

11 DDP PB11 -

7 TCK/SWCLK PB7 -

6 TMS/SWDIO PB6 -

5 TDO/TRACESWO PB5 -

4 TDI PB4 -

- PA7 XIN32 -

See footnote (2) below

- PA8 XOUT32 -

- PB9 XIN -

See footnote (3) below

- PB8 XOUT -

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

6.4 NRST Pin

The NRST pin is bidirectional. It is handled by the on-chip reset controller and can be driven low to provide a reset signal

to the external components or asserted low externally to reset the microcontroller. It will reset the Core and the

peripherals except the Backup region (RTC, RTT and Supply Controller). There is no constraint on the length of the reset

pulse and the reset controller can guarantee a minimum pulse length. The NRST pin integrates a permanent pull-up

resistor to VDDIO of about 100 kΩ. By default, the NRST pin is configured as an input.

6.5 ERASE Pin

The ERASE pin is used to reinitialize the Flash content (and some of its NVM bits) to an erased state (all bits read as

logic level 1). It integrates a pull-down resistor of about 100 kΩ to GND, so that it can be left unconnected for normal

operations.

This pin is debounced by SCLK to improve the glitch tolerance. When the ERASE pin is tied high during less than 100

ms, it is not taken into account. The pin must be tied high during more than 220 ms to perform a Flash erase operation.

The ERASE pin is a system I/O pin and can be used as a standard I/O. At startup, the ERASE pin is not configured as a

PIO pin. If the ERASE pin is used as a standard I/O, startup level of this pin must be low to prevent unwanted erasing.

Please refer to Section 11.2 “Peripheral Signal Multiplexing on I/O Lines” on page 41. Also, if the ERASE pin is used as

a standard I/O output, asserting the pin to low does not erase the Flash.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

7. Processor and Architecture

7.1 ARM Cortex-M3 Processor

zVersion 2.0

zThumb-2 (ISA) subset consisting of all base Thumb-2 instructions, 16-bit and 32-bit

zHarvard processor architecture enabling simultaneous instruction fetch with data load/store

zThree-stage pipeline

zSingle cycle 32-bit multiply

zHardware divide

zThumb and Debug states

zHandler and Thread modes

zLow latency ISR entry and exit

7.2 APB/AHB bridge

The SAM3S product embeds one peripheral bridge:

The peripherals of the bridge are clocked by MCK.

7.3 Matrix Masters

The Bus Matrix of the SAM3S product manages 4 masters, which means that each master can perform an access

concurrently with others, to an available slave.

Each master has its own decoder, which is defined specifically for each master. In order to simplify the addressing, all the

masters have the same decodings.

7.4 Matrix Slaves

The Bus Matrix of the SAM3S product manages 5 slaves. Each slave has its own arbiter, allowing a different arbitration

per slave.

Table 7-1. List of Bus Matrix Masters

Master 0 Cortex-M3 Instruction/Data

Master 1 Cortex-M3 System

Master 2 Peripheral DMA Controller (PDC)

Master 3 CRC Calculation Unit

Table 7-2. List of Bus Matrix Slaves

Slave 0 Internal SRAM

Slave 1 Internal ROM

Slave 2 Internal Flash

Slave 3 External Bus Interface

Slave 4 Peripheral Bridge

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

7.5 Master to Slave Access

All the Masters can normally access all the Slaves. However, some paths do not make sense, for example allowing

access from the Cortex-M3 S Bus to the Internal ROM. Thus, these paths are forbidden or simply not wired and shown

as “-” in the following table.

7.6 Peripheral DMA Controller

zHandles data transfer between peripherals and memories

zLow bus arbitration overhead

zOne Master Clock cycle needed for a transfer from memory to peripheral

zTwo Master Clock cycles needed for a transfer from peripheral to memory

zNext Pointer management for reducing interrupt latency requirement

The Peripheral DMA Controller handles transfer requests from the channel according to the following priorities (Low to

High priorities):

Table 7-3. SAM3S Master to Slave Access

Masters 0 1 2 3

Slaves Cortex-M3 I/D

Bus

Cortex-M3 S

Bus PDC CRCCU

0Internal SRAM - X X X

1Internal ROM X - X X

2Internal Flash X - - X

3External Bus Interface - X X X

4 Peripheral Bridge - X X -

Table 7-4. Peripheral DMA Controller

Instance Name Channel T/R 100 & 64 Pins 48 Pins

PWM Transmit xx

TWI1 Transmit xx

TWI0 Transmit xx

UART1 Transmit xx

UART0 Transmit xx

USART1 Transmit x N/A

USART0 Transmit xx

DAC Transmit x N/A

SPI Transmit xx

SSC Transmit xx

HSMCI Transmit x N/A

PIOA Transmit x x

TWI1 Receive xx

TWI0 Receive xx

UART1 Receive x N/A

UART0 Receive xx

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

7.7 Debug and Test Features

zDebug access to all memory and registers in the system, including Cortex-M3 register bank when the core is

running, halted, or held in reset.

zSerial Wire Debug Port (SW-DP) and Serial Wire JTAG Debug Port (SWJ-DP) debug access

zFlash Patch and Breakpoint (FPB) unit for implementing breakpoints and code patches

zData Watchpoint and Trace (DWT) unit for implementing watchpoints, data tracing, and system profiling

zInstrumentation Trace Macrocell (ITM) for support of printf style debugging

zIEEE1149.1 JTAG Boundary-can on All Digital Pins

USART1 Receive xx

USART0 Receive xx

ADC Receive xx

SPI Receive xx

SSC Receive xx

HSMCI Receive x N/A

PIOA Receive x x

Table 7-4. Peripheral DMA Controller (Continued)

Instance Name Channel T/R 100 & 64 Pins 48 Pins

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

8. Product Mapping

Figure 8-1. SAM3S Product Mapping

Address memory space

Code

1 MByte

bit band

regiion

1 MByte

bit band

region

0x00000000

SRAM

0x20000000

0x23FFFFFF

0x22000000

0x24000000

0x40000000

offset

peripheral

block

Code

Boot Memory

0x00000000

0x00400000

0x00800000

Reserved

0x00C00000

0x1FFFFFFF

Peripherals

HSMCI

0x40000000

SSC

0x40004000

SPI

0x40008000

0x4000C000

TC0 TC0

0x40010000

TC0 TC1

+0x40

TC0 TC2

+0x80

TC1 TC3

0x40014000

TC1 TC4

+0x40

TC1 TC5

+0x80

TWI0

0x40018000

TWI1

0x4001C000

PWM

0x40020000

USART0

0x40024000

USART1

0x40028000

Reserved

0x4002C000

Reserved

0x40030000

UDP

0x40034000

ADC

0x40038000

DACC

0x4003C000

ACC

0x40040000

CRCCU

0x40044000

0x40048000

System Controller

0x400E0000

0x400E2600

0x40100000

0x40200000

0x40400000

0x60000000

External RAM

SMC Chip Select 0

0x60000000

SMC Chip Select 1

Undefined

32 MBytes

bit band alias

0x61000000

SMC Chip Select 2

0x62000000

SMC Chip Select 3

0x63000000

0x64000000

0x9FFFFFFF

System Controller

SMC

0x400E0000

MATRIX

0x400E0200

PMC

0x400E0400

UART0

UART1

0x400E0600

CHIPID

0x400E0740

0x400E0800

EFC

0x400E0A00

0x400E0C00

PIOA

0x400E0E00

PIOB

0x400E1000

PIOC

0x400E1200

RSTC

0x400E1400

SUPC

+0x10

RTT

+0x30

WDT

+0x50

RTC

+0x60

GPBR

+0x90

0x400E1600

0x4007FFFF

Internal Flash

Internal ROM

Reserved

Peripherals

External SRAM

0xA0000000

System

0xE0000000

0xFFFFFFFF

Reserved

32 MBytes

bit band alias

Reserved

0x60000000

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

9. Memories

9.1 Embedded Memories

9.1.1 Internal SRAM

The ATSAM3S4 product (256-Kbyte internal Flash version) embeds a total of 48 Kbytes high-speed SRAM.

The ATSAM3S2 product (128-Kbyte internal Flash version) embeds a total of 32 Kbytes high-speed SRAM.

The ATSAM3S1 product (64-Kbyte internal Flash version) embeds a total of 16 Kbytes high-speed SRAM.

The SRAM is accessible over System Cortex-M3 bus at address 0x2000 0000.

The SRAM is in the bit band region. The bit band alias region is mapped from 0x2200 0000 to 0x23FF FFFF.

9.1.2 Internal ROM

The SAM3S product embeds an Internal ROM, which contains the SAM Boot Assistant (SAM-BA), In Application

Programming routines (IAP) and Fast Flash Programming Interface (FFPI).

At any time, the ROM is mapped at address 0x0080 0000.

9.1.3 Embedded Flash

9.1.3.1 Flash Overview

The Flash of the ATSAM3S4 (256-Kbytes internal Flash version) is organized in one bank of 1024 pages (Single plane)

of 256 bytes.

The Flash of the ATSAM3S2 (128-Kbytes internal Flash version) is organized in one bank of 512 pages (Single plane) of

256 bytes.

The Flash of the ATSAM3S1 (64-Kbytes internal Flash version) is organized in one bank of 256 pages (Single plane) of

256 bytes.

The Flash contains a 128-byte write buffer, accessible through a 32-bit interface.

9.1.3.2 Flash Power Supply

The Flash is supplied by VDDCORE.

9.1.3.3 Enhanced Embedded Flash Controller

The Enhanced Embedded Flash Controller (EEFC) manages accesses performed by the masters of the system. It

enables reading the Flash and writing the write buffer. It also contains a User Interface, mapped on the APB.

The Enhanced Embedded Flash Controller ensures the interface of the Flash block with the 32-bit internal bus. Its 128-bit

wide memory interface increases performance.

The user can choose between high performance or lower current consumption by selecting either 128-bit or 64-bit

access. It also manages the programming, erasing, locking and unlocking sequences of the Flash using a full set of

commands.

One of the commands returns the embedded Flash descriptor definition that informs the system about the Flash

organization, thus making the software generic.

9.1.3.4 Flash Speed

The user needs to set the number of wait states depending on the frequency used.

For more details, refer to the AC Characteristics sub section in the product Electrical Characteristics Section.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

9.1.3.5 Lock Regions

Several lock bits used to protect write and erase operations on lock regions. A lock region is composed of several

consecutive pages, and each lock region has its associated lock bit.

If a locked-region’s erase or program command occurs, the command is aborted and the EEFC triggers an interrupt.

The lock bits are software programmable through the EEFC User Interface. The command “Set Lock Bit” enables the

protection. The command “Clear Lock Bit” unlocks the lock region.

Asserting the ERASE pin clears the lock bits, thus unlocking the entire Flash.

9.1.3.6 Security Bit Feature

The SAM3S features a security bit, based on a specific General Purpose NVM bit (GPNVM bit 0). When the security is

enabled, any access to the Flash, SRAM, Core Registers and Internal Peripherals either through the ICE interface or

through the Fast Flash Programming Interface, is forbidden. This ensures the confidentiality of the code programmed in

the Flash.

This security bit can only be enabled, through the command “Set General Purpose NVM Bit 0” of the EEFC User

Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1, and after a full Flash erase is

performed. When the security bit is deactivated, all accesses to the Flash, SRAM, Core registers, Internal Peripherals

are permitted.

It is important to note that the assertion of the ERASE pin should always be longer than 200 ms.

As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal operation. However, it is

safer to connect it directly to GND for the final application.

9.1.3.7 Calibration Bits

NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits are factory configured and

cannot be changed by the user. The ERASE pin has no effect on the calibration bits.

9.1.3.8 Unique Identifier

Each device integrates its own 128-bit unique identifier. These bits are factory configured and cannot be changed by the

user. The ERASE pin has no effect on the unique identifier.

9.1.3.9 Fast Flash Programming Interface

The Fast Flash Programming Interface allows programming the device through a multiplexed fully-handshaked parallel

port. It allows gang programming with market-standard industrial programmers.

The FFPI supports read, page program, page erase, full erase, lock, unlock and protect commands.

The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered when TST is tied high and

PA0 and PA1 are tied low.

9.1.3.10SAM-BA® Boot

The SAM-BA Boot is a default Boot Program which provides an easy way to program in-situ the on-chip Flash memory.

The SAM-BA Boot Assistant supports serial communication via the UART and USB.

The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).

Table 9-1. Number of Lock Bits

Product Number of Lock Bits Lock Region Size

ATSAM3S4 16 16 kbytes (64 pages)

ATSAM3S2 8 16 kbytes (64 pages)

ATSAM3S1 4 16 kbytes (64 pages)

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

9.1.3.11GPNVM Bits

The SAM3S features two GPNVM bits that can be cleared or set respectively through the commands “Clear GPNVM Bit”

and “Set GPNVM Bit” of the EEFC User Interface.

9.1.4 Boot Strategies

The system always boots at address 0x0. To ensure maximum boot possibilities, the memory layout can be changed via

GPNVM.

A general-purpose NVM (GPNVM) bit is used to boot either on the ROM (default) or from the Flash.

The GPNVM bit can be cleared or set respectively through the commands “Clear General-purpose NVM Bit” and “Set

General-purpose NVM Bit” of the EEFC User Interface.

Setting GPNVM Bit 1 selects the boot from the Flash, clearing it selects the boot from the ROM. Asserting ERASE clears

the GPNVM Bit 1 and thus selects the boot from the ROM by default.

9.2 External Memories

The SAM3S features an External Bus Interface to provide the interface to a wide range of external memories and to any

parallel peripheral.

9.2.1 Static Memory Controller

z8-bit Data Bus

zUp to 24-bit Address Bus (up to 16 MBytes linear per chip select)

zUp to 4 chip selects, Configurable Assignment

zMultiple Access Modes supported

zChip Select, Write enable or Read enable Control Mode

zAsynchronous read in Page Mode supported (4- up to 32-byte page size)

zMultiple device adaptability

zControl signals programmable setup, pulse and hold time for each Memory Bank

zMultiple Wait State Management

zProgrammable Wait State Generation

zExternal Wait Request

zProgrammable Data Float Time

zSlow Clock mode supported

zAdditional Logic for NAND Flash

Table 9-2. General Purpose Non-volatile Memory Bits

GPNVMBit[#] Function

0 Security bit

1 Boot mode selection

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

10. System Controller

The System Controller is a set of peripherals, which allow handling of key elements of the system, such as power, resets,

clocks, time, interrupts, watchdog, etc...

See the system controller block diagram in Figure 10-1 on page 34.

Figure 10-1. System Controller Block Diagram

Software Controlled

Voltage Regulator

Matrix

SRAM

Watchdog

Timer

Cortex-M3

Flash

Peripherals

Peripheral

Bridge

Zero-Power

Power-on Reset

Supply

Monitor

(Backup)

RTC

Power

Management

Controller

Embedded

32 kHz RC

Oscillator

Xtal 32 kHz

Oscillator

Supply

Controller

Brownout

Detector

(Core)

Reset

Controller

Backup Power Supply

Core Power Supply

PLLA

vr_on

vr_mode

out

rtc_alarm

SLCK

rtc_nreset

proc_nreset

periph_nreset

ice_nreset

Master Clock

MCK

SLCK

NRST

MAINCK

FSTT0 - FSTT15

XIN32

XOUT32

osc32k_xtal_en

Slow Clock

SLCK

osc32k_rc_en

VDDIO

VDDCORE

VDDOUT

ADVREF

ADx

WKUP0 - WKUP15

bod_core_on

lcore_brown_out

RTT

rtt_alarm

SLCK

rtt_nreset

XIN

XOUT

VDDIO

VDDIN

PIOx

USB

Transeivers

VDDIO

DDP

DDM

MAINCK

DAC Analog

Circuitry

DACx

PLLB

PLLBCK

PLLACK

Embedded

12 / 8 / 4 MHz

Oscillator

Main Clock

MAINCK

SLCK

3 - 20 MHz

XTAL Oscillator

FSTT0 - FSTT15 are possible Fast Startup Sources, generated by WKUP0-WKUP15 Pins,

but are not physical pins.

VDDIO

XTALSEL

General Purpose

Backup Registers

vddcore_nreset

PIOA/B/C

Input/Output Buffers

ADC Analog

Circuitry

Analog

Comparator

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

10.1 System Controller and Peripheral Mapping

Please refer to Section 8-1 “SAM3S Product Mapping” on page 30.

All the peripherals are in the bit band region and are mapped in the bit band alias region.

10.2 Power-on-Reset, Brownout and Supply Monitor

The SAM3S embeds three features to monitor, warn and/or reset the chip:

• Power-on-Reset on VDDIO

• Brownout Detector on VDDCORE

• Supply Monitor on VDDIO

10.2.1 Power-on-Reset

The Power-on-Reset monitors VDDIO. It is always activated and monitors voltage at start up but also during power down.

If VDDIO goes below the threshold voltage, the entire chip is reset. For more information, refer to the Electrical

Characteristics section of the datasheet.

10.2.2 Brownout Detector on VDDCORE

The Brownout Detector monitors VDDCORE. It is active by default. It can be deactivated by software through the Supply

Controller (SUPC_MR). It is especially recommended to disable it during low-power modes such as wait or sleep modes.

If VDDCORE goes below the threshold voltage, the reset of the core is asserted. For more information, refer to the

Supply Controller (SUPC) and Electrical Characteristics sections of the datasheet.

10.2.3 Supply Monitor on VDDIO

The Supply Monitor monitors VDDIO. It is not active by default. It can be activated by software and is fully programmable

with 16 steps for the threshold (between 1.9V to 3.4V). It is controlled by the Supply Controller (SUPC). A sample mode

is possible. It allows to divide the supply monitor power consumption by a factor of up to 2048. For more information,

refer to the SUPC and Electrical Characteristics sections of the datasheet.

10.3 Reset Controller

The Reset Controller is based on a Power-on-Reset cell, and a Supply Monitor on VDDCORE.

The Reset Controller is capable to return to the software the source of the last reset, either a general reset, a wake-up

reset, a software reset, a user reset or a watchdog reset.

The Reset Controller controls the internal resets of the system and the NRST pin input/output. It is capable to shape a

reset signal for the external devices, simplifying to a minimum connection of a push-button on the NRST pin to implement

a manual reset.

The configuration of the Reset Controller is saved as supplied on VDDIO.

10.4 Supply Controller (SUPC)

The Supply Controller controls the power supplies of each section of the processor and the peripherals (via Voltage

regulator control)

The Supply Controller has its own reset circuitry and is clocked by the 32 kHz Slow clock generator.

The reset circuitry is based on a zero-power power-on reset cell and a brownout detector cell. The zero-power power-on

reset allows the Supply Controller to start properly, while the software-programmable brownout detector allows detection

of either a battery discharge or main voltage loss.

The Slow Clock generator is based on a 32 kHz crystal oscillator and an embedded 32 kHz RC oscillator. The Slow Clock

defaults to the RC oscillator, but the software can enable the crystal oscillator and select it as the Slow Clock source.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

The Supply Controller starts up the device by sequentially enabling the internal power switches and the Voltage

Regulator, then it generates the proper reset signals to the core power supply.

It also enables to set the system in different low power modes and to wake it up from a wide range of events.

10.5 Clock Generator

The Clock Generator is made up of:

zOne Low Power 32768Hz Slow Clock oscillator with bypass mode

zOne Low-Power RC oscillator

zOne 3-20 MHz Crystal Oscillator, which can be bypassed

zOne Fast RC oscillator factory programmed, 3 output frequencies can be selected: 4, 8 or 12 MHz. By default 4

MHz is selected.

zOne 60 to 130 MHz PLL (PLLB) providing a clock for the USB Full Speed Controller

zOne 60 to 130 MHz programmable PLL (PLLA), capable to provide the clock MCK to the processor and to the

peripherals. The PLLA input frequency is from 3.5 to 20 MHz.

Figure 10-2. Clock Generator Block Diagram

10.6 Power Management Controller

The Power Management Controller provides all the clock signals to the system. It provides:

zthe Processor Clock, HCLK

zthe Free running processor clock, FCLK

zthe Cortex SysTick external clock

zthe Master Clock, MCK, in particular to the Matrix and the memory interfaces

zthe USB Clock, UDPCK

Power

Management

Controller

XIN

XOUT Main Clock

MAINCK

ControlStatus

PLL and

Divider A

PLLA Clock

PLLACK

3-20 MHz

Main

Oscillator

PLL and

Divider B

On Chip

32 kHz

RC OSC Slow Clock

SLCK

XIN32

XOUT32

Slow Clock

Oscillator

Clock Generator

XTALSEL

PLLB Clock

PLLBCK

On Chip

12/8/4 MHz

RC OSC MAINSEL

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

zindependent peripheral clocks, typically at the frequency of MCK

zthree programmable clock outputs: PCK0, PCK1 and PCK2

The Supply Controller selects between the 32 kHz RC oscillator or the crystal oscillator. The unused oscillator is disabled

automatically so that power consumption is optimized.

By default, at startup the chip runs out of the Master Clock using the fast RC oscillator running at 4 MHz.

The user can trim the 8 and 12 MHz RC Oscillator frequency by software.

Figure 10-3. SAM3S Power Management Controller Block Diagram

The SysTick calibration value is fixed at 8000 which allows the generation of a time base of 1 ms with SystTick clock at 8

MHz (max HCLK/8 = 64 MHz/8).

10.7 Watchdog Timer

z16-bit key-protected only-once-Programmable Counter

zWindowed, prevents the processor to be in a dead-lock on the watchdog access.

10.8 SysTick Timer

z24-bit down counter

zSelf-reload capability

zFlexible System timer

MCK

periph_clk[..]

int

SLCK

MAINCK

PLLACK

Prescaler

/1,/2,/4,...,/64

HCK

Processor

Clock

Controller

Sleep Mode

Master Clock Controller

Peripherals

Clock Controller

ON/OFF

USB Clock Controller

SLCK

MAINCK

PLLACK

Prescaler

/1,/2,/4,...,/64

Programmable Clock Controller

PLLBCK

pck[..]

PLLBCK

UDPCK

ON/OFF

FCLK

SystTick

Divider

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

10.9 Real Time Timer

zReal Time Timer, allowing backup of time with different accuracies

z32-bit free-running back-up counter

zIntegrates a 16-bit programmable prescaler running on slow clock

zAlarm register capable to generate a wake-up of the system through the Shut Down Controller

10.10 Real Time Clock

zLow power consumption

zFull asynchronous design

zTwo hundred year calendar

zProgrammable Periodic Interrupt

zAlarm and update parallel load

zControl of alarm and update Time/Calendar Data In

10.11 General Purpose Backup Registers

zEight 32-bit general-purpose backup registers

10.12 Nested Vectored Interrupt Controller

zThirty maskable external interrupts

zSixteen priority levels

zProcessor state automatically saved on interrupt entry, and restored on

zDynamic reprioritization of interrupts

zPriority grouping.

zselection of preempting interrupt levels and non-preempting interrupt levels.

zSupport for tail-chaining and late arrival of interrupts.

zback-to-back interrupt processing without the overhead of state saving and restoration between interrupts.

zProcessor state automatically saved on interrupt entry, and restored on interrupt exit, with no instruction overhead.

10.13 Chip Identification

zChip Identifier (CHIPID) registers permit recognition of the device and its revision.

zJTAG ID: 0x05B2D03F

Table 10-1. SAM3S Chip IDs Register

Chip Name Flash Size

(KBytes) Pin Count DBGU_CIDR CHIPID_EXID

ATSAM3S4A (Rev A) 256 48 0x28800960 0x0

ATSAM3S2A (Rev A) 128 48 0x288A0760 0x0

ATSAM3S1A (Rev A) 64 48 0x28890560 0x0

ATSAM3S4B (Rev A) 256 64 0x28900960 0x0

ATSAM3S2B (Rev A) 128 64 0x289A0760 0x0

ATSAM3S1B (Rev A) 64 64 0x28990560 0x0

ATSAM3S4C (Rev A) 256 100 0x28A00960 0x0

ATSAM3S2C (Rev A) 128 100 0x28AA0760 0x0

ATSAM3S1C (Rev A) 64 100 0x28A90560 0x0

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

10.14 UART

zTwo-pin UART

zImplemented features are 100% compatible with the standard Atmel USART

zIndependent receiver and transmitter with a common programmable Baud Rate Generator

zEven, Odd, Mark or Space Parity Generation

zParity, Framing and Overrun Error Detection

zAutomatic Echo, Local Loopback and Remote Loopback Channel Modes

zSupport for two PDC channels with connection to receiver and transmitter

10.15 PIO Controllers

z3 PIO Controllers, PIOA, PIOB and PIOC (100-pin version only) controlling a maximum of 79 I/O Lines

zFully programmable through Set/Clear Registers

zMultiplexing of four peripheral functions per I/O Line

zFor each I/O Line (whether assigned to a peripheral or used as general purpose I/O)

zInput change, rising edge, falling edge, low level and level interrupt

zDebouncing and Glitch filter

zMulti-drive option enables driving in open drain

zProgrammable pull-up or pull-down on each I/O line

zPin data status register, supplies visibility of the level on the pin at any time

zSynchronous output, provides Set and Clear of several I/O lines in a single write

Table 10-2. PIO available according to pin count

Version 48 pin 64 pin 100 pin

PIOA 21 32 32

PIOB 13 15 15

PIOC --32

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

11. Peripherals

11.1 Peripheral Identifiers

Table 11-1 defines the Peripheral Identifiers of the SAM3S. A peripheral identifier is required for the control of the

peripheral interrupt with the Nested Vectored Interrupt Controller and for the control of the peripheral clock with the

Power Management Controller.

Table 11-1. Peripheral Identifiers

Instance ID Instance Name NVIC Interrupt PMC Clock

Control Instance Description

0 SUPC X Supply Controller

1 RSTC X Reset Controller

2 RTC X Real Time Clock

3 RTT X Real Time Timer

4 WDT X Watchdog Timer

5 PMC X Power Management Controller

6 EEFC X Enhanced Embedded Flash Controller

7- - Reserved

8 UART0 X X UART 0

9 UART1 X X UART 1

10 SMC X X SMC

11 PIOA X X Parallel I/O Controller A

12 PIOB X X Parallel I/O Controller B

13 PIOC X X Parallel I/O Controller C

14 USART0 X X USART 0

15 USART1 X X USART 1

16 - - - Reserved

17 - - - Reserved

18 HSMCI X X High Speed Multimedia Card Interface

19 TWI0 X X Two Wire Interface 0

20 TWI1 X X Two Wire Interface 1

21 SPI X X Serial Peripheral Interface

22 SSC X X Synchronous Serial Controller

23 TC0 X X Timer/Counter 0

24 TC1 X X Timer/Counter 1

25 TC2 X X Timer/Counter 2

26 TC3 X X Timer/Counter 3

27 TC4 X X Timer/Counter 4

28 TC5 X X Timer/Counter 5

29 ADC X X Analog-to-Digital Converter

30 DACC X X Digital-to-Analog Converter

31 PWM X X Pulse Width Modulation

32 CRCCU X X CRC Calculation Unit

33 ACC X X Analog Comparator

34 UDP X X USB Device Port

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

11.2 Peripheral Signal Multiplexing on I/O Lines

The SAM3S product features 2 PIO controllers on 48-pin and 64-pin versions (PIOA, PIOB) or 3 PIO controllers on the

100-pin version, (PIOA, PIOB, PIOC), that multiplex the I/O lines of the peripheral set.

The SAM3S 64-pin and 100-pin PIO Controllers control up to 32 lines. (See, Table 10-2.) Each line can be assigned to

one of three peripheral functions: A, B or C. The multiplexing tables in the following pages define how the I/O lines of the

peripherals A, B and C are multiplexed on the PIO Controllers. The column “Comments” has been inserted in this table

for the user’s own comments; it may be used to track how pins are defined in an application.

Note that some peripheral functions which are output only, might be duplicated within the tables.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

11.2.1 PIO Controller A Multiplexing

Table 11-2. Multiplexing on PIO Controller A (PIOA)

I/O Line Peripheral A Peripheral B Peripheral C Extra Function System Function Comments

PA0 PWMH0 TIOA0 A17 WKUP0 High drive

PA1 PWMH1 TIOB0 A18 WKUP1 High drive

PA2 PWMH2 SCK0 DATRG WKUP2 High drive

PA3 TWD0 NPCS3 High drive

PA4 TWCK0 TCLK0 WKUP3

PA5 RXD0 NPCS3 WKUP4

PA6 TXD0 PCK0

PA7 RTS0 PWMH3 XIN32

PA8 CTS0 ADTRG WKUP5 XOUT32

PA9 URXD0 NPCS1 PWMFI0 WKUP6

PA10 UTXD0 NPCS2

PA11 NPCS0 PWMH0 WKUP7

PA12 MISO PWMH1

PA13 MOSI PWMH2

PA14 SPCK PWMH3 WKUP8

PA15 TF TIOA1 PWML3 WKUP14/PIODCEN1

PA16 TK TIOB1 PWML2 WKUP15/PIODCEN2

PA17 TD PCK1 PWMH3 AD0

PA18 RD PCK2 A14 AD1

PA19 RK PWML0 A15 AD2/WKUP9

PA20 RF PWML1 A16 AD3/WKUP10

PA21 RXD1 PCK1 AD8 64/100-pin versions

PA22 TXD1 NPCS3 NCS2 AD9 64/100-pin versions

PA23 SCK1 PWMH0 A19 PIODCCLK 64/100-pin versions

PA24 RTS1 PWMH1 A20 PIODC0 64/100-pin versions

PA25 CTS1 PWMH2 A23 PIODC1 64/100-pin versions

PA26 DCD1 TIOA2 MCDA2 PIODC2 64/100-pin versions

PA27 DTR1 TIOB2 MCDA3 PIODC3 64/100-pin versions

PA28 DSR1 TCLK1 MCCDA PIODC4 64/100-pin versions

PA29 RI1 TCLK2 MCCK PIODC5 64/100-pin versions

PA30 PWML2 NPCS2 MCDA0 WKUP11/PIODC6 64/100-pin versions

PA31 NPCS1 PCK2 MCDA1 PIODC7 64/100-pin versions

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

11.2.2 PIO Controller B Multiplexing

Table 11-3. Multiplexing on PIO Controller B (PIOB)

I/O Line Peripheral A Peripheral B Peripheral C Extra Function System Function Comments

PB0 PWMH0 AD4

PB1 PWMH1 AD5

PB2 URXD1 NPCS2 AD6/ WKUP12

PB3 UTXD1 PCK2 AD7

PB4 TWD1 PWMH2 TDI

PB5 TWCK1 PWML0 WKUP13 TDO/TRACESWO

PB6 TMS/SWDIO

PB7 TCK/SWCLK

PB8 XOUT

PB9 XIN

PB10 DDM

PB11 DDP

PB12 PWML1 ERASE

PB13 PWML2 PCK0 DAC0 64/100-pin versions

PB14 NPCS1 PWMH3 DAC1 64/100-pin versions

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

11.2.3 PIO Controller C Multiplexing

Table 11-4. Multiplexing on PIO Controller C (PIOC)

I/O Line Peripheral A Peripheral B Peripheral C Extra Function System Function Comments

PC0 D0 PWML0 100-pin version

PC1 D1 PWML1 100-pin version

PC2 D2 PWML2 100-pin version

PC3 D3 PWML3 100-pin version

PC4 D4 NPCS1 100-pin version

PC5 D5 100-pin version

PC6 D6 100-pin version

PC7 D7 100-pin version

PC8 NWE 100-pin version

PC9 NANDOE 100-pin version

PC10 NANDWE 100-pin version

PC11 NRD 100-pin version

PC12 NCS3 AD12 100-pin version

PC13 NWAIT PWML0 AD10 100-pin version

PC14 NCS0 100-pin version

PC15 NCS1 PWML1 AD11 100-pin version

PC16 A21/NANDALE 100-pin version

PC17 A22/NANDCLE 100-pin version

PC18 A0 PWMH0 100-pin version

PC19 A1 PWMH1 100-pin version

PC20 A2 PWMH2 100-pin version

PC21 A3 PWMH3 100-pin version

PC22 A4 PWML3 100-pin version

PC23 A5 TIOA3 100-pin version

PC24 A6 TIOB3 100-pin version

PC25 A7 TCLK3 100-pin version

PC26 A8 TIOA4 100-pin version

PC27 A9 TIOB4 100-pin version

PC28 A10 TCLK4 100-pin version

PC29 A11 TIOA5 AD13 100-pin version

PC30 A12 TIOB5 AD14 100-pin version

PC31 A13 TCLK5 100-pin version

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

12. Embedded Peripherals Overview

12.1 Serial Peripheral Interface (SPI)

zSupports communication with serial external devices

zFour chip selects with external decoder support allow communication with up to 15 peripherals

zSerial memories, such as DataFlash and 3-wire EEPROMs

zSerial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and Sensors

zExternal co-processors

zMaster or slave serial peripheral bus interface

z8- to 16-bit programmable data length per chip select

zProgrammable phase and polarity per chip select

zProgrammable transfer delays between consecutive transfers and between clock and data per chip select

zProgrammable delay between consecutive transfers

zSelectable mode fault detection

zVery fast transfers supported

zTransfers with baud rates up to MCK

zThe chip select line may be left active to speed up transfers on the same device

12.2 Two Wire Interface (TWI)

zMaster, Multi-Master and Slave Mode Operation

zCompatibility with Atmel two-wire interface, serial memory and I2C compatible devices

zOne, two or three bytes for slave address

zSequential read/write operations

zBit Rate: Up to 400 kbit/s

zGeneral Call Supported in Slave Mode

zConnecting to PDC channel capabilities optimizes data transfers in Master Mode only

zOne channel for the receiver, one channel for the transmitter

zNext buffer support

12.3 Universal Asynchronous Receiver Transceiver (UART)

zTwo-pin UART

zIndependent receiver and transmitter with a common programmable Baud Rate Generator

zEven, Odd, Mark or Space Parity Generation

zParity, Framing and Overrun Error Detection

zAutomatic Echo, Local Loopback and Remote Loopback Channel Modes

zSupport for two PDC channels with connection to receiver and transmitter

12.4 Universal Synchronous Asynchronous Receiver Transceiver (USART)

zProgrammable Baud Rate Generator with Fractional Baud rate support

z5- to 9-bit full-duplex synchronous or asynchronous serial communications

z1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode

zParity generation and error detection

zFraming error detection, overrun error detection

zMSB- or LSB-first

zOptional break generation and detection

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

zBy 8 or by-16 over-sampling receiver frequency

zHardware handshaking RTS-CTS

zReceiver time-out and transmitter timeguard

zOptional Multi-drop Mode with address generation and detection

zOptional Manchester Encoding

zFull modem line support on USART1 (DCD-DSR-DTR-RI)

zRS485 with driver control signal

zISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards

zNACK handling, error counter with repetition and iteration limit

zSPI Mode

zMaster or Slave

zSerial Clock programmable Phase and Polarity

zSPI Serial Clock (SCK) Frequency up to MCK/4

zIrDA modulation and demodulation

zCommunication at up to 115.2 Kbps

zTest Modes

zRemote Loopback, Local Loopback, Automatic Echo

12.5 Synchronous Serial Controller (SSC)

zProvides serial synchronous communication links used in audio and telecom applications (with CODECs in Master

or Slave Modes, I2S, TDM Buses, Magnetic Card Reader)

zContains an independent receiver and transmitter and a common clock divider

zOffers configurable frame sync and data length

zReceiver and transmitter can be programmed to start automatically or on detection of different event on the frame

sync signal

zReceiver and transmitter include a data signal, a clock signal and a frame synchronization signal

12.6 Timer Counter (TC)

zSix 16-bit Timer Counter Channels

zWide range of functions including:

zFrequency Measurement

zEvent Counting

zInterval Measurement

zPulse Generation

zDelay Timing

zPulse Width Modulation

zUp/down Capabilities

zEach channel is user-configurable and contains:

zThree external clock inputs

zFive internal clock inputs

zTwo multi-purpose input/output signals

zTwo global registers that act on all three TC Channels

zQuadrature decoder

zAdvanced line filtering

zPosition / revolution / speed

z2-bit Gray Up/Down Counter for Stepper Motor

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

12.7 Pulse Width Modulation Controller (PWM)

zOne Four-channel 16-bit PWM Controller, 16-bit counter per channel

zCommon clock generator, providing Thirteen Different Clocks

zA Modulo n counter providing eleven clocks

zTwo independent Linear Dividers working on modulo n counter outputs

zIndependent channel programming

zIndependent Enable Disable Commands

zIndependent Clock Selection

zIndependent Period and Duty Cycle, with Double Buffering

zProgrammable selection of the output waveform polarity

zProgrammable center or left aligned output waveform

zIndependent Output Override for each channel

zIndependent complementary Outputs with 12-bit dead time generator for each channel

zIndependent Enable Disable Commands

zIndependent Clock Selection

zIndependent Period and Duty Cycle, with Double Buffering

zSynchronous Channel mode

zSynchronous Channels share the same counter

zMode to update the synchronous channels registers after a programmable number of periods

zConnection to one PDC channel

zOffers Buffer transfer without Processor Intervention, to update duty cycle of synchronous channels

zindependent event lines which can send up to 4 triggers on ADC within a period

zProgrammable Fault Input providing an asynchronous protection of outputs

zStepper motor control (2 Channels)

12.8 High Speed Multimedia Card Interface (HSMCI)

z4-bit or 1-bit Interface

zCompatibility with MultiMedia Card Specification Version 4.3

zCompatibility with SD and SDHC Memory Card Specification Version 2.0

zCompatibility with SDIO Specification Version V1.1.

zCompatibility with CE-ATA Specification 1.1

zCards clock rate up to Master Clock divided by 2

zBoot Operation Mode support

zHigh Speed mode support

zEmbedded power management to slow down clock rate when not used

zHSMCI has one slot supporting

zOne MultiMediaCard bus (up to 30 cards) or

zOne SD Memory Card

zOne SDIO Card

zSupport for stream, block and multi-block data read and write

12.9 USB Device Port (UDP)

zUSB V2.0 full-speed compliant,12 Mbits per second.

zEmbedded USB V2.0 full-speed transceiver

zEmbedded 2688-byte dual-port RAM for endpoints

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

zEight endpoints

zEndpoint 0: 64 bytes

zEndpoint 1 and 2: 64 bytes ping-pong

zEndpoint 3: 64 bytes

zEndpoint 4 and 5: 512 bytes ping-pong

zEndpoint 6 and 7: 64 bytes ping-pong

zPing-pong Mode (two memory banks) for Isochronous and bulk endpoints

zSuspend/resume logic

zIntegrated Pull-up on DDP

zPull-down resistor on DDM and DDP when disabled

12.10 Analog-to-Digital Converter (ADC)

zup to 16 Channels,

z10/12-bit resolution

zup to 1 MSample/s

zprogrammable sequence of conversion on each channel

zIntegrated temperature sensor

zSingle ended/differential conversion

zProgrammable gain: 1, 2, 4

12.11 Digital-to-Analog Converter (DAC)

zUp to 2 channel 12-bit DAC

zUp to 2 mega-samples conversion rate in single channel mode

zFlexible conversion range

zMultiple trigger sources for each channel

z2 Sample/Hold (S/H) outputs

zBuilt-in offset and gain calibration

zPossibility to drive output to ground

zPossibility to use as input to analog comparator or ADC (as an internal wire and without S/H stage)

zTwo PDC channels

zPower reduction mode

12.12 Static Memory Controller

z16-Mbyte Address Space per Chip Select

z8- bit Data Bus

zWord, Halfword, Byte Transfers

zProgrammable Setup, Pulse And Hold Time for Read Signals per Chip Select

zProgrammable Setup, Pulse And Hold Time for Write Signals per Chip Select

zProgrammable Data Float Time per Chip Select

zExternal Wait Request

zAutomatic Switch to Slow Clock Mode

zAsynchronous Read in Page Mode Supported: Page Size Ranges from 4 to 32 Bytes

zNAND FLASH additional logic supporting NAND Flash with Multiplexed Data/Address buses

zHardware Configurable number of chip select from 1 to 4

zProgrammable timing on a per chip select basis

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

12.13 Analog Comparator

zOne analog comparator

zHigh speed option vs. low power option

zSelectable input hysteresis:

z0, 20 mV, 50 mV

zMinus input selection:

zDAC outputs

zTemperature Sensor

zADVREF

zAD0 to AD3 ADC channels

zPlus input selection:

zAll analog inputs

zoutput selection:

zInternal signal

zexternal pin

zselectable inverter

zInterrupt on:

zRising edge, Falling edge, toggle

12.14 Cyclic Redundancy Check Calculation Unit (CRCCU)

z32-bit cyclic redundancy check automatic calculation

zCRC calculation between two addresses of the memory

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

13. Package Drawings

The SAM3S series devices are available in LQFP, QFN and TFBGA packages.

Figure 13-1. 100-lead LQFP Package Mechanical Drawing

Note : 1. This drawing is for general information only. Refer to JEDEC Drawing MS-026 for additional information.

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 13-2. 100-ball TFBGA Package Drawing

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 13-3. 64- and 48-lead LQFP Package Drawing

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Table 13-1. 48-lead LQFP Package Dimensions (in mm)

Symbol Millimeter Inch

Min Nom Max Min Nom Max

A – – 1.60 – – 0.063

A1 0.05 – 0.15 0.002 – 0.006

A2 1.35 1.40 1.45 0.053 0.055 0.057

D 9.00 BSC 0.354 BSC

D1 7.00 BSC 0.276 BSC

E 9.00 BSC 0.354 BSC

E1 7.00 BSC 0.276 BSC

R2 0.08 – 0.20 0.003 – 0.008

R1 0.08 – – 0.003 – –

q 0° 3.5° 7° 0° 3.5° 7°

θ10° – – 0° – –

θ211° 12° 13° 11° 12° 13°

θ311° 12° 13° 11° 12° 13°

c 0.09 – 0.20 0.004 – 0.008

L 0.45 0.60 0.75 0.018 0.024 0.030

L1 1.00 REF 0.039 REF

S 0.20 – – 0.008 – –

b 0.17 0.20 0.27 0.007 0.008 0.011

e 0.50 BSC. 0.020 BSC.

D2 5.50 0.217

E2 5.50 0.217

Tolerances of Form and Position

aaa 0.20 0.008

bbb 0.20 0.008

ccc 0.08 0.003

ddd 0.08 0.003

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Table 13-2. 64-lead LQFP Package Dimensions (in mm)

Symbol Millimeter Inch

Min Nom Max Min Nom Max

A – – 1.60 – – 0.063

A1 0.05 – 0.15 0.002 – 0.006

A2 1.35 1.40 1.45 0.053 0.055 0.057

D 12.00 BSC 0.472 BSC

D1 10.00 BSC 0.383 BSC

E 12.00 BSC 0.472 BSC

E1 10.00 BSC 0.383 BSC

R2 0.08 – 0.20 0.003 – 0.008

R1 0.08 – – 0.003 – –

q 0° 3.5° 7° 0° 3.5° 7°

θ10° – – 0° – –

θ211° 12° 13° 11° 12° 13°

θ311° 12° 13° 11° 12° 13°

c 0.09 – 0.20 0.004 – 0.008

L 0.45 0.60 0.75 0.018 0.024 0.030

L1 1.00 REF 0.039 REF

S 0.20 – – 0.008 – –

b 0.17 0.20 0.27 0.007 0.008 0.011

e 0.50 BSC. 0.020 BSC.

D2 7.50 0.285

E2 7.50 0.285

Tolerances of Form and Position

aaa 0.20 0.008

bbb 0.20 0.008

ccc 0.08 0.003

ddd 0.08 0.003

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 13-4. 48-pad QFN Package

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Table 13-3. 48-pad QFN Package Dimensions (in mm)

Symbol Millimeter Inch

Min Nom Max Min Nom Max

A – – 090 – – 0.035

A1 – – 0.050 – – 0.002

A2 – 0.65 0.70 – 0.026 0.028

A3 0.20 REF 0.008 REF

b 0.18 0.20 0.23 0.007 0.008 0.009

D 7.00 bsc 0.276 bsc

D2 5.45 5.60 5.75 0.215 0.220 0.226

E 7.00 bsc 0.276 bsc

E2 5.45 5.60 5.75 0.215 0.220 0.226

L 0.35 0.40 0.45 0.014 0.016 0.018

e 0.50 bsc 0.020 bsc

R 0.09 – – 0.004 – –

Tolerances of Form and Position

aaa 0.10 0.004

bbb 0.10 0.004

ccc 0.05 0.002

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Figure 13-5. 64-pad QFN Package Drawing

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

14. Ordering Information

Table 14-1. Ordering Codes for SAM3S Series Devices

Ordering Code MRL A MRL B Flash

(Kbytes) Package

Type Temperature

Operating Range

ATSAM3S4CA-AU A – 256 QFP100 Green Industrial

-40°C to 85°C

ATSAM3S4CA-CU A – 256 BGA100 Green Industrial

-40°C to 85°C

ATSAM3S4BA-AU A – 256 QFP64 Green Industrial

-40°C to 85°C

ATSAM3S4BA-MU A – 256 QFN64 Green Industrial

-40°C to 85°C

ATSAM3S4AA-AU A – 256 QFP48 Green Industrial

-40°C to 85°C

ATSAM3S4AA-MU A – 256 QFN48 Green Industrial

-40°C to 85°C

ATSAM3S2CA-AU A – 128 QFP100 Green Industrial

-40°C to 85°C

ATSAM3S2CA-CU A – 128 BGA100 Green Industrial

-40°C to 85°C

ATSAM3S2BA-AU A – 128 QFP64 Green Industrial

-40°C to 85°C

ATSAM3S2BA-MU A – 128 QFN64 Green Industrial

-40°C to 85°C

ATSAM3S2AA-AU A – 128 QFP48 Green Industrial

-40°C to 85°C

ATSAM3S2AA-MU A – 128 QFN48 Green Industrial

-40°C to 85°C

ATSAM3S1CA-AU A – 64 QFP100 Green Industrial

-40°C to 85°C

ATSAM3S1CA-CU A – 64 BGA100 Green Industrial

-40°C to 85°C

ATSAM3S1BA-AU A – 64 QFP64 Green Industrial

-40°C to 85°C

ATSAM3S1BA-MU A – 64 QFN64 Green Industrial

-40°C to 85°C

ATSAM3S1AA-AU A – 64 QFP48 Green Industrial

-40°C to 85°C

ATSAM3S1AA-MU A – 64 QFN48 Green Industrial

-40°C to 85°C

ATSAM3S1CB-AU – B 64 QFP100 Green Industrial

-40°C to 85°C

ATSAM3S1CB-CU – B 64 BGA100 Green Industrial

-40°C to 85°C

ATSAM3S1BB-AU – B 64 QFP64 Green Industrial

-40°C to 85°C

ATSAM3S1BB-MU – B 64 QFN64 Green Industrial

-40°C to 85°C

ATSAM3S1AB-AU – B 64 QFP48 Green Industrial

-40°C to 85°C

ATSAM3S1AB-MU – B 64 QFN48 Green Industrial

-40°C to 85°C

SAM3S [SUMMARY]

6500ES–ATARM–11-Feb-13

Revision History

Doc. Rev Comments Change

Request Ref.

6500ES

Section 1. “Features”updated, “Low Power Modes” , Sleep and Backup modes, down to 1.8 µA in

Backup mode

Figure 8-1, "SAM3S Product Mapping", SRAM associated 1 MByte bit band region mapping changed:

0x22000000 to 0x23FFFFFF.

Document format updated, subsequently pagination changed

Section 14. “Ordering Information” Introduced MRL B for SAM3S1 parts..

rfo

8545

6500DS

Replace all mention to 100-ball LFBGA into 100-ball TFBGA.

Add table note 5 in Table 3-1, “Signal Description List”.

Add MOSCRCEN bit details in Section 5.5.2 “Wait Mode”.

Section 9.1.3.9 “Fast Flash Programming Interface” updated.

Notes under Figure 5-1, "Single Supply" and Figure 5-2, "Core Externally Supplied" modified.

Cross-References (1) added for 64-pin packages in table Table 1-1, “Configuration Summary”.

Pin 22 value changed for PA23/PGMD11 in Table 4-1, “100-lead LQFP SAM3S4/2/1C Pinout”.

"High Frequency Asynchronous clocking mode" removed from Section 12.7 “Pulse Width Modulation

Controller (PWM)”

“Write Protected Registers” added in “Description” , in Peripherals list.

ADC column values updated in Table 1-1, “Configuration Summary”.

8044

7632

7639

7668-7901

7887

8033

8093

8095

8213

rfo

6500CS

Missing PGMD8 to 15 added to Table 4-1, “100-lead LQFP SAM3S4/2/1C Pinout” and Table 4-2,

“100-ball TFBGA SAM3S4/2/1C Pinout”.

Section 5.7 “Fast Startup” updated.

Typo fixed on back page: ‘techincal’ --> ‘technical’.

Typos fixed in Section 1. “Features”.

Missing title added to Table 14-1.

PLLA input frequency range updated in Section 10.5 “Clock Generator”.

A sentence completed in Section 5.5.2 “Wait Mode”.

Last sentence removed from Section 9.1.3.10 “SAM-BA® Boot”.

‘three GPNVM bits’ replaced by ‘two GPNVM bits’ in Section 9.1.3.11 “GPNVM Bits”.

Leftover sentence removed from Section 4.1 “SAM3S4/2/1C Package and Pinout”.

rfo

7536

7524

7494

7492

7428

7394

6500BS

“Packages” on page 2, package size or pitch updated.

Table 1-1, “Configuration Summary”, ADC column updated, footnote gives precision on reserved

channel.

Table 4-2, “100-ball TFBGA SAM3S4/2/1C Pinout”, pinout information is available.

Figure 5-1, "Single Supply",Figure 5-2, "Core Externally Supplied" , updated notes below figures.

Figure 5-2, "Core Externally Supplied", Figure 5-3, "Backup Battery", ADC, DAC, Analog Comparator

supply is 2.0V-3.6V.

Section 12.13 “Analog Comparator”, “Peripherals” on page 2, reference to “window function”

removed.

Section 9.1.3.8 “Unique Identifier”, Each device integrates its own 128-bit unique identifier.

7214

6981

7201

7243/rfo

7103

7307

6500AS First issue

Atmel Corporation

1600 Technology Drive

San Jose, CA 95110

USA

Tel: (+1) (408) 441-0311

Fax: (+1) (408) 487-2600

www.atmel.com

Atmel Asia Limited

Unit 01-5 & 16, 19F

BEA Tower, Millennium City 5

418 Kwun Tong Road

Kwun Tong, Kowloon

HONG KONG

Tel: (+852) 2245-6100

Fax: (+852) 2722-1369

Atmel Munich GmbH

Business Campus

Parkring 4

D-85748 Garching b. Munich

GERMANY

Tel: (+49) 89-31970-0

Fax: (+49) 89-3194621

Atmel Japan G.K.

16F Shin-Osaki Kangyo Bldg

1-6-4 Osaki, Shinagawa-ku

Tokyo 141-0032

JAPAN

Tel: (+81) (3) 6417-0300

Fax: (+81) (3) 6417-0370

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this

document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES

NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,

CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF

INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no

representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time

without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in,

automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Atmel®, Atmel logo and combinations thereof, SAM-BA® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. ARM®,

ARM®Powered logo, Cortex®, Thumb®-2 and others are registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of

others.