SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 FEATURES 1 * Member of the Texas Instruments Widebus+TM Family * Control Inputs VIH/VIL Levels Are Referenced to VCCA Voltage * VCC Isolation Feature - If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State * Overvoltage-Tolerant Inputs/Outputs Allow Mixed-Voltage-Mode Data Communications * Fully Configurable Dual-Rail Design Allows Each Port to Operate Over Full 1.2-V to 3.6-V Power-Supply Range * Ioff Supports Partial-Power-Down Mode Operation 2 * * * * I/Os Are 4.6-V Tolerant Max Data Rates - 380 Mbps (1.8-V to 3.3-V Translation) - 200 Mbps (< 1.8-V to 3.3-V Translation) - 200 Mbps (Translate to 2.5 V or 1.8V) - 150 Mbps (Translate to 1.5 V) - 100 Mbps (Translate to 1.2 V) Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 4000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) DESCRIPTION/ORDERING INFORMATION This 32-bit noninverting bus transceiver uses two separate configurable power-supply rails. The SN74AVC32T245 is optimized to operate with VCCA/VCCB set at 1.4 V to 3.6 V. It is operational with VCCA/VCCB as low as 1.2 V. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.2 V to 3.6 V. This allows for universal low-voltage bidirectional translation between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes. The SN74AVC32T245 is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are effectively isolated. The SN74AVC32T245 is designed so that the control pins (1DIR, 2DIR, 3DIR, 4DIR, 1OE, 2OE, 3OE, and 4OE) are supplied by VCCA. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The VCC isolation feature ensures that if either VCC input is at GND, then both ports are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION TA PACKAGE (1) (2) ORDERABLE PART NUMBER LFBGA - GKE -40C to 85C LFBGA - ZKE (Pb-free) LFBGA - ZRL (Pb-free) (1) (2) TOP-SIDE MARKING SN74AVC32T245GKER Tape and reel SN74AVC32T245ZKER WY245 SN74AVC32T245ZRLR Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus+ is a trademark of Texas Instruments. UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2007, Texas Instruments Incorporated SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 GKE OR ZKE PACKAGE (TOP VIEW) 1 2 3 4 5 ZRL PACKAGE (TOP VIEW) 6 1 2 3 4 5 6 A A B B C C D D E E F F G G H H J J K L K M L N M P N R P T R T TERMINAL ASSIGNMENTS 1 2 3 4 5 6 A 1B2 1B1 1DIR 1OE 1A1 1A2 B 1B4 1B3 GND GND 1A3 1A4 C 1B6 1B5 VCCB VCCA 1A5 1A6 D 1B8 1B7 GND GND 1A7 1A8 E 2B2 2B1 GND GND 2A1 2A2 F 2B4 2B3 VCCB VCCA 2A3 2A4 G 2B6 2B5 GND GND 2A5 2A6 H 2B7 2B8 2DIR 2OE 2A8 2A7 J 3B2 3B1 3DIR 3OE 3A1 3A2 K 3B4 3B3 GND GND 3A3 3A4 L 3B6 3B5 VCCB VCCA 3A5 3A6 M 3B8 3B7 GND GND 3A7 3A8 N 4B2 4B1 GND GND 4A1 4A2 P 4B4 4B3 VCCB VCCA 4A3 4A4 R 4B6 4B5 GND GND 4A5 4A6 T 4B7 4B8 4DIR 4OE 4A8 4A7 FUNCTION TABLE (EACH 8-BIT SECTION) INPUTS OE 2 DIR OPERATION L L B data to A bus L H A data to B bus H X Isolation Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 www.ti.com SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS SCES553E - MAY 2004 - REVISED AUGUST 2007 LOGIC DIAGRAM (POSITIVE LOGIC) 1DIR A3 2DIR A4 1A1 H4 1OE A5 2A1 A2 H3 E5 E2 1B1 To Seven Other Channels 3DIR 2B1 To Seven Other Channels J3 4DIR J4 3A1 2OE T4 3OE J5 4A1 J2 T3 4OE N5 N2 3B1 To Seven Other Channels Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 4B1 To Seven Other Channels Submit Documentation Feedback 3 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) VCCA VCCB Supply voltage range VI Input voltge range (2) MIN MAX -0.5 4.6 I/O ports (A port) -0.5 4.6 I/O ports (B port) -0.5 4.6 Control inputs -0.5 4.6 A port -0.5 4.6 B port -0.5 4.6 A port -0.5 VCCA + 0.5 B port -0.5 VCCB + 0.5 UNIT V V VO Voltage range applied to any output in the high-impedance or power-off state (2) VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA 100 mA Continuous current through each VCCA, VCCB, and GND JA Package thermal impedance (4) Tstg Storage temperature range (1) (2) (3) (4) 4 GKE/ZKE package 40 ZRL package TBD -65 150 V V C/W C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input voltage and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 Recommended Operating Conditions (1) (2) (3) VCCI VCCO MIN MAX UNIT VCCA Supply voltage 1.2 3.6 V VCCB Supply voltage 1.2 3.6 V VIH High-level input voltage VIL Low-level input voltage VIH High-level input voltage VIL Low-level input voltage VI Input voltage Data inputs (4) Data inputs (4) DIR (referenced to VCCA) (5) DIR (referenced to VCCA) (5) 1.2 V to 1.95 V VCCI x 0.65 1.95 V to 2.7 V 1.6 2.7 V to 3.6 V 2 1.2 V to 1.95 V VCCI x 0.35 1.95 V to 2.7 V 0.7 2.7 V to 3.6 V 0.8 1.2 V to 1.95 V VCCA x 0.65 1.95 V to 2.7 V 1.6 2.7 V to 3.6 V 2 Output voltage IOH VCCA x 0.35 1.95 V to 2.7 V 0.7 IOL 3.6 Active state 0 VCCO 3-state 0 3.6 Low-level output current t/v Input transition rise or fall rate TA Operating free-air temperature (1) (2) (3) (4) (5) V 0.8 0 High-level output current V V 1.2 V to 1.95 V 2.7 V to 3.6 V VO V 1.2 V -3 1.4 V to 1.6 V -6 1.65 V to 1.95 V -8 2.3 V to 2.7 V -9 3 V to 3.6 V -12 1.2 V 3 1.4 V to 1.6 V 6 1.65 V to 1.95 V 8 2.3 V to 2.7 V 9 3 V to 3.6 V 12 -40 V V mA mA 5 ns/V 85 C VCCI is the VCC associated with the data input port. VCCO is the VCC associated with the output port. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. For VCCI values not specified in the data sheet, VIH min = VCCI x 0.7 V, VIL max = VCCI x 0.3 V. For VCCI values not specified in the data sheet, VIH min = VCCA x 0.7 V, VIL max = VCCA x 0.3 V. Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 Submit Documentation Feedback 5 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) (1) (2) PARAMETER TEST CONDITIONS IOH = -100 A VOH A or B port Ioff A or B port IOZ (3) A or B port TYP 1.2 V 1.2 V 1.4 V 1.4 V 1.05 1.65 V 1.65 V 1.2 IOH = -9 mA 2.3 V 2.3 V 1.75 IOH = -12 mA 3V 3V 2.3 VI = VIH V IOL = 3 mA 1.2 V 1.2 V IOL = 6 mA 1.4 V 1.4 V 0.35 1.65 V 1.65 V 0.45 IOL = 9 mA 2.3 V 2.3 V 0.55 IOL = 12 mA 3V 3V 0.7 VI = VIL VI = VCCA or GND 1.2 V to 3.6 V 1.2 V to 3.6 V 0.15 0.025 0.25 1 0V 0 to 3.6 V 0.1 2.5 5 0 to 3.6 V 0V 0.1 2.5 5 3.6 V 3.6 V 0.5 2.5 5 VI = VCCI or GND, IO = 0 VI = VCCI or GND, IO = 0 V A A VI or VO = 0 to 3.6 V VO = VCCO or GND, VI = VCCI or GND, OE =VIH UNIT 0.2 A 50 0V 3.6 V -10 3.6 V 0V 50 1.2 V to 3.6 V 1.2 V to 3.6 V ICCA + ICCB MAX 0.95 1.2 V to 3.6 V 1.2 V to 3.6 V VI = VCCI or GND, IO = 0 ICCB MIN VCCO - 0.2 V 1.2 V to 3.6 V 1.2 V to 3.6 V ICCA -40C TO 85C MAX IOH = -6 mA IOL = 8 mA II TA = 25C MIN 1.2 V to 3.6 V 1.2 V to 3.6 V IOL = 100 A Control inputs VCCB IOH = -3 mA IOH = -8 mA VOL VCCA A 50 0V 3.6 V 50 3.6 V 0V -10 1.2 V to 3.6 V 1.2 V to 3.6 V 90 A A Ci Control inputs VI = 3.3 V or GND 3.3 V 3.3 V 3.5 pF Cio A or B port VO = 3.3 V or GND 3.3 V 3.3 V 7 pF (1) (2) (3) 6 VCCO is the VCC associated with the output port. VCCI is the VCC associated with the input port. For I/O ports, the parameter IOZ includes the input leakage current. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.2 V (see Figure 11) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V VCCB = 1.8 V VCCB = 2.5 V VCCB = 3.3 V TYP TYP TYP TYP TYP 4.1 3.3 3 2.8 3.2 4.1 3.3 3 2.8 3.2 4.4 4 3.8 3.6 3.5 4.4 4 3.8 3.6 3.5 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6 4.6 4 3.4 3.2 6 4.6 4 3.4 3.2 6.6 6.6 6.6 6.6 6.8 6.6 6.6 6.6 6.6 6.8 6 4.9 4.9 4.2 5.3 6 4.9 4.9 4.2 5.3 UNIT ns ns ns ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.5 V 0.1 V (see Figure 11) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 3.6 0.5 6.2 0.5 5.2 0.5 4.1 0.5 3.7 3.6 0.5 6.2 0.5 5.2 0.5 4.1 0.5 3.7 3.3 0.5 6.2 0.5 5.9 0.5 5.6 0.5 5.5 3.3 0.5 6.2 0.5 5.9 0.5 5.6 0.5 5.5 4.3 1 10.1 1 10.1 1 10.1 1 10.1 4.3 1 10.1 1 10.1 1 10.1 1 10.1 5.6 1 10.1 0.5 8.1 0.5 5.9 0.5 5.2 5.6 1 10.1 0.5 8.1 0.5 5.9 0.5 5.2 4.5 1.5 9.1 1.5 9.1 1.5 9.1 1.5 9.1 4.5 1.5 9.1 1.5 9.1 1.5 9.1 1.5 9.1 5.5 1.5 8.7 1.5 7.5 1 6.5 1 6.3 5.5 1.5 8.7 1.5 7.5 1 6.5 1 6.3 Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 Submit Documentation Feedback UNIT ns ns ns ns ns ns 7 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.8 V 0.15 V (see Figure 11) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 3.4 0.5 5.9 0.5 4.8 0.5 3.7 0.5 3.3 3.4 0.5 5.9 0.5 4.8 0.5 3.7 0.5 3.3 3 0.5 5.2 0.5 4.8 0.5 4.5 0.5 4.4 3 0.5 5.2 0.5 4.8 0.5 4.5 0.5 4.4 3.4 1 7.8 1 7.8 1 7.8 1 7.8 3.4 1 7.8 1 7.8 1 7.8 1 7.8 5.4 1 9.2 0.5 7.4 0.5 5.3 0.5 4.5 5.4 1 9.2 0.5 7.4 0.5 5.3 0.5 4.5 4.2 1.5 7.7 1.5 7.7 1.5 7.7 1.5 7.7 4.2 1.5 7.7 1.5 7.7 1.5 7.7 1.5 7.7 5.2 1.5 8.4 1.5 7.1 1 5.9 1 5.7 5.2 1.5 8.4 1.5 7.1 1 5.9 1 5.7 UNIT ns ns ns ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 2.5 V 0.2 V (see Figure 11) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ 8 FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 3.2 0.5 5.6 0.5 4.5 0.5 3.3 0.5 2.8 3.2 0.5 5.6 0.5 4.5 0.5 3.3 0.5 2.8 2.6 0.5 4.1 0.5 3.7 0.5 3.3 0.5 3.2 2.6 0.5 4.1 0.5 3.7 0.5 3.3 0.5 3.2 2.5 0.5 5.3 0.5 5.3 0.5 5.3 0.5 5.3 2.5 0.5 5.3 0.5 5.3 0.5 5.3 0.5 5.3 5.2 0.5 9.4 0.5 7.3 0.5 5.1 0.5 4.5 5.2 0.5 9.4 0.5 7.3 0.5 5.1 0.5 4.5 3 1 6.1 1 6.1 1 6.1 1 6.1 3 1 6.1 1 6.1 1 6.1 1 6.1 5 1 7.9 1 6.6 1 6.1 1 5.2 5 1 7.9 1 6.6 1 6.1 1 5.2 Submit Documentation Feedback UNIT ns ns ns ns ns ns Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 Switching Characteristics over recommended operating free-air temperature range, VCCA = 3.3 V 0.3 V (see Figure 11) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.5 V 0.1 V VCCB = 1.2 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 3.2 0.5 5.5 0.5 4.4 0.5 3.2 0.5 2.7 3.2 0.5 5.5 0.5 4.4 0.5 3.2 0.5 2.7 2.8 0.5 3.7 0.5 3.3 0.5 2.8 0.5 2.7 2.8 0.5 3.7 0.5 3.3 0.5 2.8 0.5 2.7 2.2 0.5 4.3 0.5 4.2 0.5 4.1 0.5 4 2.2 0.5 4.3 0.5 4.2 0.5 4.1 0.5 4 5.1 0.5 9.3 0.5 7.2 0.5 4.9 0.5 4 5.1 0.5 9.3 0.5 7.2 0.5 4.9 0.5 4 3.4 0.5 5 0.5 5 0.5 5 0.5 5 3.4 0.5 5 0.5 5 0.5 5 0.5 5 4.9 1 7.7 1 6.5 1 5.2 0.5 5 4.9 1 7.7 1 6.5 1 5.2 0.5 5 UNIT ns ns ns ns ns ns Operating Characteristics TA = 25C VCCA = VCCB = 1.2 V VCCA = VCCB = 1.5 V VCCA = VCCB = 1.8 V VCCA = VCCB = 2.5 V VCCA = VCCB = 3.3 V TYP TYP TYP TYP TYP 1 1 1 1 2 1 1 1 1 1 13 13 14 15 16 Outputs disabled 1 1 1 1 1 Outputs enabled 13 13 14 15 16 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 PARAMETER A to B CpdA (1) B to A A to B CpdB (1) B to A (1) TEST CONDITIONS Outputs enabled Outputs disabled Outputs enabled Outputs disabled Outputs enabled CL = 0, f = 10 MHz, tr = tf = 1 ns UNIT pF CL = 0, f = 10 MHz, tr = tf = 1 ns pF Outputs disabled Power dissipation capacitance per transceiver Table 1. Typical Total Static Power Consumption (ICCA + ICCB) VCCB VCCA 0V 1.2 V 1.5 V 1.8 V 2.5 V 3.3 V 0V 0 <1 <1 <1 <1 <1 1.2 V <1 <2 <2 <2 <2 2 1.5 V <1 <2 <2 <2 <2 2 1.8 V <1 <2 <2 <2 <2 <2 2.5 V <1 2 <2 <2 <2 <2 3.3 V <1 2 <2 <2 <2 <2 Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 UNIT A Submit Documentation Feedback 9 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 TYPICAL CHARACTERISTICS 6 6 TA = 25C VCCA = 1.2 V TA = 25C VCCA = 1.2 V 5 tPHL - Propagation Delay - ns tPLH - Propagation Delay - ns 5 4 3 2 x VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 0 0 10 20 30 40 CL - Load Capacitance - pF 50 4 3 x 2 VCCB = 1.2 V VCCB = 1.5 V + VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 0 60 0 10 20 30 40 CL - Load Capacitance - pF Figure 1. 6 TA = 25C VCCA = 1.5 V TA = 25C VCCA = 1.5 V 5 tPHL - Propagation Delay - ns tPLH - Propagation Delay - ns 5 4 3 x 2 VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 0 10 20 30 40 50 4 3 x 2 VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 60 0 0 10 CL - Load Capacitance - pF Figure 3. 10 60 Figure 2. 6 0 50 20 30 40 50 60 CL - Load Capacitance - pF Figure 4. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) 6 6 TA = 25C VCCA = 1.8 V TA = 25C VCCA = 1.8 V 5 tPHL - Propagation Delay - ns tPLH - Propagation Delay - ns 5 4 3 2 x VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 0 0 10 20 30 40 50 4 3 2 x VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 0 0 60 30 Figure 6. tPHL - Propagation Delay - ns 4 3 2 x VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 20 30 40 50 60 x TA = 25C VCCA = 2.5 V 5 10 50 Figure 5. 6 0 40 CL - Load Capacitance - pF TA = 25C VCCA = 2.5 V tPLH - Propagation Delay - ns 20 CL - Load Capacitance - pF 6 0 10 VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 5 4 3 2 1 0 60 0 10 CL - Load Capacitance - pF Figure 7. 20 30 40 50 60 CL - Load Capacitance - pF Figure 8. Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 Submit Documentation Feedback 11 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 TYPICAL CHARACTERISTICS (continued) 6 6 TA = 25C VCCA = 3.3 V VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 5 tPHL - Propagation Delay - ns tPLH - Propagation Delay - ns 5 4 3 2 x VCCB = 1.2 V + VCCB = 1.5 V VCCB = 1.8 V H VCCB = 2.5 V VCCB = 3.3 V 1 0 0 10 20 30 40 50 60 4 3 2 1 0 0 10 CL - Load Capacitance - pF 20 30 40 50 60 CL - Load Capacitance - pF Figure 9. 12 x TA = 25C VCCA = 3.3 V Figure 10. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 SN74AVC32T245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES553E - MAY 2004 - REVISED AUGUST 2007 PARAMETER MEASUREMENT INFORMATION 2 x VCCO S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCCO GND RL tw LOAD CIRCUIT VCCI VCCI/2 Input VCCO CL RL VTP 1.2 V 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 15 pF 15 pF 15 pF 15 pF 15 pF 2 k 2 k 2 k 2 k 2 k 0.1 V 0.1 V 0.15 V 0.15 V 0.3 V VCCI/2 0V VOLTAGE WAVEFORMS PULSE DURATION VCCA Output Control (low-level enabling) VCCA/2 VCCA/2 0V tPZL VCCI Input VCCI/2 VCCI/2 0V tPLH Output tPHL VOH VCCO/2 VOL VCCO/2 tPLZ VCCO Output Waveform 1 S1 at 2 x VCCO (see Note B) VCCO/2 VOL + VTP VOL tPZH tPHZ Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VCCO/2 VOH - VTP VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 , dv/dt 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. VCCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. Figure 11. Load Circuit and Voltage Waveforms Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC32T245 Submit Documentation Feedback 13 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) SN74AVC32T245GKER ACTIVE LFBGA GKE 96 1000 TBD SNPB Level-2-235C-1 YEAR SN74AVC32T245ZKER ACTIVE LFBGA ZKE 96 1000 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR SN74AVC32T245ZRLR ACTIVE BGA MICROSTAR JUNIOR ZRL 96 2500 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74AVC32T245GKER LFBGA GKE 96 1000 330.0 24.4 5.7 13.7 2.0 8.0 24.0 Q1 SN74AVC32T245ZKER LFBGA ZKE 96 1000 330.0 24.4 5.7 13.7 2.0 8.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74AVC32T245GKER LFBGA GKE 96 1000 333.2 345.9 31.8 SN74AVC32T245ZKER LFBGA ZKE 96 1000 333.2 345.9 31.8 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated