Features
• High intensity
• Choice of 3 bright colors
High Eciency Red
Yellow
High Performance Green
• Popular T-1 diameter package
• Selected minimum intensities
• Narrow viewing angle
• General purpose leads
• Reliable and rugged
• Available on tape and reel
• For more information, please refer to Tape and Reel
Option data sheet
Description
This family of T-1 lamps is specially designed for applica-
tions requiring higher on-axis intensity than is achievable
with a standard lamp. The light generated is focused to a
narrow beam to achieve this eect.
Package Dimensions
HLMP-132x Series, HLMP-142x Series,
HLMP-152x Series
T-1 (3 mm) High Intensity LED Lamps
Data Sheet
Selection Guide
Part Number
Package
Description Color
Luminous Intensity
Iv (mcd) @ 10 mA
Min. Max.
HLMP-1321 Tinted,
Non-diused
High Eciency
Red
8.6 –
HLMP-1321-G00xx 8.6 –
HLMP-1420 Microtinted,
Non-diused
Yellow
9.2 –
HLMP-1421 Tinted,
Non-diused
9.2 –
HLMP-1421-F00xx 9.2 –
HLMP-1520 Microtinted,
Non-diused
Green
6.7 –
HLMP-1521 Tinted,
Non-diused
6.7 –
HLMP-1521-E00xx 6.7 –
2
Absolute Maximum Ratings at TA = 25°C
Parameter Red Yellow Green Units
Peak Forward Current 90 60 90 mA
Average Forward Current[1] 25 20 25 mA
DC Current[2] 30 20 30 mA
Power Dissipation[3] 135 85 135 mW
Reverse Voltage (IR = 100 µA) 5 5 5 V
Transient Forward Current[4] (10 µsec Pulse) 500 500 500 mA
LED Junction Temperature 110 110 110 °C
Operating Temperature Range -40 to +100 -40 to +100 -20 to +100 °C
Storage Temperature Range -40 to +100 -40 to +100 -40 to +100
Notes:
1. See Figure 5 (Red), 10 (Yellow), or 15 (Green) to establish pulsed operating conditions.
2. For Red and Green series derate linearly from 50°C at 0.5 mA/°C. For Yellow series derate linearly from 50°C at 0.2 mA/°C.
3. For Red and Green series derate power linearly from 25°C at 1.8 mW/°C. For Yellow series derate power linearly from 50°C at 1.6 mW/°C.
4. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die
and wirebond. It is not recommended that the device be operated at peak currents beyond the peak forward current listed in the Absolute
Maximum Ratings.
Part Numbering System
HLMP - 1 x xx - x x x xx
Mechanical Option
00: Bulk
01: Tape & Reel, Crimped Leads
02: Tape & Reel, Straight Leads
A1: Right Angle Housing, Uneven Leads
A2: Right Angle Housing, Even Leads
Color Bin Options
0: Full Color Bin Distribution
Maximum Iv Bin Options
0: Open (no max. limit)
Others: Please refer to the Iv Bin Table
Minimum Iv Bin Options
Please refer to the Iv Bin Table
Lens Options
20: Untinted or Microtinted, Non-diused
21: Tinted, Non-diused
Color Options
3: GaP HER
4: GaP Yellow
5: GaP Green
Package Options
1: T-1 (3 mm)
3
Electrical Characteristics at TA = 25°C
Symbol
Description
Device
Min. Typ. Max. Units Test ConditionsHLMP-
IVLuminous Intensity 1320
1321
8.6
8.6
30
30
mcd IF = 10 mA
(Figure 3)
1420
1421
9.2
9.2
15
15
mcd IF = 10 mA
(Figure 8)
1520
1521
6.7
6.7
22
22
mcd IF = 10 mA
(Figure 3)
2q1/2Including Angle Between
Half Luminous Intensity
Points
All 45 Deg. IF = 10 mA
See Note 1
(Figures 6, 11, 16, 21)
lPEAK Peak Wavelength 132x 635 nm Measurement
at Peak (Figure 1)
142X
152X
583
565
Dl1/2 Spectral Line Halfwidth 132x 40 nm
142X
152X
36
28
ldDominant Wavelength 132x 626 nm See Note 2 (Figure 1)
142X
152X
585
569
tsSpeed of Response 132x 90 ns
142X
152X
90
500
C Capacitance 132x 11 pF VF = 0; f = 1 MHz
142X
152X
15
18
RqJ-PIN Thermal Resistance All 290 °C/W Junction to
Cathode Lead
VFForward Voltage 132x 1.9 2.4 V IF = 10 mA
142X
152X
2.0
2.1
2.4
2.7
VRReverse Breakdown Voltage All 5.0 V IR = 100 µA
hVLuminous Ecacy 132x 145 lumens
watt See Note 3
142X
152X
500
595
Notes:
1. q1/2 is the o-axis angle at which the luminous intensity is half the axial luminous intensity.
2. The dominant wavelength, ld, is derived from the CIE chromaticity diagram and represents the single wavelength which denes the color of
the device.
3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = lv/hv, where lv is the luminous intensity in candelas and hv is the
luminous ecacy in lumens/watt.
4
Figure 3. Relative luminous intensity vs. DC
forward current.
Figure 2. Forward current vs. forward voltage
characteristics.
Figure 4. Relative eciency (luminous intensity
per unit current) vs. peak LED current.
Figure 5. Maximum tolerable peak current vs.
pulse duration. (IDC MAX as per MAX ratings).
Figure 6. Relative luminous intensity vs. angular displacement.
Figure 1. Relative intensity vs. wavelength.
T-1 High Eciency Red Non-Diused
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 2.0 3.0 4.0 5.0
90
80
70
60
50
40
30
20
10
0
IDC – DC CURRENT PER LED – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10mA)
0 5 10 15 20 3025
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IPEAK – PEAK CURRENT PER LED – mA
IPEAK – RELATIVE EFFICIENCY
0 10 20 40 50 70 8030 60 90
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
tp – PULSE DURATION – µs
RATIO OF MAXIMUM
TOLERABLE PEAK CURRENT
TO MAXIMUM TOLERABLE
DC CURRENT
IPEAK MAX.
IDC MAX.
1.0 10 100 1,000 10,000
100 Hz
300 Hz
1 KHz
3 KHz
10 KHz
30 KHz
100 KHz
300 KHz
6
5
4
3
2
1
0° 20°
NON-DIFFUSED
40° 60° 80° 100°
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
.8
.6
.4
.2
1.0
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 2.0 3.0 4.0 5.0
90
80
70
60
50
40
30
20
10
0
IDC – DC CURRENT PER LED – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10mA)
0 5 10 15 20 3025
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IPEAK – PEAK CURRENT PER LED – mA
IPEAK – RELATIVE EFFICIENCY
0 10 20 40 50 70 8030 60 90
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 2.0 3.0 4.0 5.0
90
80
70
60
50
40
30
20
10
0
IDC – DC CURRENT PER LED – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10mA)
0 5 10 15 20 3025
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IPEAK – PEAK CURRENT PER LED – mA
IPEAK – RELATIVE EFFICIENCY
0 10 20 40 50 70 8030 60 90
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
tp – PULSE DURATION – µs
RATIO OF MAXIMUM
TOLERABLE PEAK CURRENT
TO MAXIMUM TOLERABLE
DC CURRENT
IPEAK MAX.
IDC MAX.
1.0 10 100 1,000 10,000
100 Hz
300 Hz
1 KHz
3 KHz
10 KHz
30 KHz
100 KHz
300 KHz
6
5
4
3
2
1
0° 20°
NON-DIFFUSED
40° 60° 80° 100°
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
.8
.6
.4
.2
1.0
5
T-1 Yellow Non-Diused
Figure 10. Maximum tolerable peak current vs.
pulse duration. (IDCMAX as per MAX ratings).
Figure 11. Relative luminous intensity vs. angular displacement.
Figure 8. Relative luminous intensity vs.
forward current.
Figure 7. Forward current vs. forward voltage
characteristics.
Figure 9. Relative eciency (luminous intensity
per unit current) vs. peak current.
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 1.5 2.0 3.02.5 3.5 4.0
60
50
40
30
20
10
0
IF – FORWARD CURRENT – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10 mA)
0 5 10 15 20
2.5
2.0
1.5
1.0
0.5
0
TA = 25°
IPEAK – PEAK CURRENT – mA
RELATIVE LUMINOUS EFFICIENCY
(NORMALIZED AT 10 mA DC)
0 40302010 50 60
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
tp – PULSE DURATION – µs
RATIO OF MAXIMUM
TOLERABLE PEAK CURRNT
TO MAXIMUM TOLERABLE
DC CURRENT
IPEAK MAX.
IDC MAX.
1.0 10 100 1,000 10,000
100 Hz
300 Hz
1 KHz
3 KHz
10 KHz
30 KHz
100 KHz
300 KHz
6
5
4
3
2
1
0° 20°
NON-DIFFUSED
40° 60° 80° 100°
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
.8
.6
.4
.2
1.0
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 1.5 2.0 3.02.5 3.5 4.0
60
50
40
30
20
10
0
IF – FORWARD CURRENT – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10 mA)
0 5 10 15 20
2.5
2.0
1.5
1.0
0.5
0
TA = 25°
IPEAK – PEAK CURRENT – mA
RELATIVE LUMINOUS EFFICIENCY
(NORMALIZED AT 10 mA DC)
0 40302010 50 60
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
tp – PULSE DURATION – µs
RATIO OF MAXIMUM
TOLERABLE PEAK CURRNT
TO MAXIMUM TOLERABLE
DC CURRENT
IPEAK MAX.
IDC MAX.
1.0 10 100 1,000 10,000
100 Hz
300 Hz
1 KHz
3 KHz
10 KHz
30 KHz
100 KHz
300 KHz
6
5
4
3
2
1
0° 20°
NON-DIFFUSED
40° 60° 80° 100°
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
.8
.6
.4
.2
1.0
6
T-1 Green Non-Diused
Figure 13. Relative luminous intensity vs.
forward current.
Figure 12. Forward current vs. forward voltage
characteristics.
Figure 14. Relative eciency (luminous inten-
sity per unit current) vs. peak LED current.
Figure 15. Maximum tolerable peak current vs.
pulse duration. (IDCMAX as per MAX ratings).
Figure 16. Relative luminous intensity vs. angular displacement.
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 2.0 5.04.03.0
90
80
70
60
50
40
30
20
10
0
IPEAK – PEAK CURRENT PER LED – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10mA)
0 105 353020 402515
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IPEAK – PEAK CURRENT PER LED – mA
RELATIVE EFFICIENCY
0 2010 8070 1006030 40 50 90
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
tp – PULSE DURATION – µs
RATIO OF MAXIMUM
TOLERABLE PEAK CURRNT
TO MAXIMUM TOLERABLE
DC CURRENT
IPEAK MAX.
IDC MAX.
1.0 10 100 1,000 10,000
100 Hz
300 Hz
1 KHz
3 KHz
10 KHz
30 KHz
100 KHz
300 KHz
6
5
4
3
2
1
0° 20°
NON-DIFFUSED
40° 60° 80° 100°
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
.8
.6
.4
.2
1.0
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 2.0 5.04.03.0
90
80
70
60
50
40
30
20
10
0
IPEAK – PEAK CURRENT PER LED – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10mA)
0 105 353020 402515
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IPEAK – PEAK CURRENT PER LED – mA
RELATIVE EFFICIENCY
0 2010 8070 1006030 40 50 90
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
VF – FORWARD VOLTAGE – V
IF – FORWARD CURRENT – mA
1.0 2.0 5.04.03.0
90
80
70
60
50
40
30
20
10
0
IPEAK – PEAK CURRENT PER LED – mA
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 10mA)
0 105 353020 402515
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IPEAK – PEAK CURRENT PER LED – mA
RELATIVE EFFICIENCY
0 2010 8070 1006030 40 50 90
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
0.7
tp – PULSE DURATION – µs
RATIO OF MAXIMUM
TOLERABLE PEAK CURRNT
TO MAXIMUM TOLERABLE
DC CURRENT
IPEAK MAX.
IDC MAX.
1.0 10 100 1,000 10,000
100 Hz
300 Hz
1 KHz
3 KHz
10 KHz
30 KHz
100 KHz
300 KHz
6
5
4
3
2
1
0° 20°
NON-DIFFUSED
40° 60° 80° 100°
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
.8
.6
.4
.2
1.0
7
Intensity Bin Limits
Color Bin
Intensity Range (mcd)
Min. Max.
Green
E 7.6 12.0
F 12.0 19.1
G 19.1 30.7
H 30.7 49.1
I 49.1 78.5
J 78.5 125.7
K 125.7 201.1
L 201.1 289.0
M 289.0 417.0
N 417.0 680.0
O 680.0 1100.0
P 1100.0 1800.0
Q 1800.0 2700.0
R 2700.0 4300.0
S 4300.0 6800.0
T 6800.0 10800.0
U 10800.0 16000.0
V 16000.0 25000.0
W 25000.0 40000.0
Maximum tolerance for each bin limit is ±18%.
Intensity Bin Limits
Color Bin
Intensity Range (mcd)
Min. Max.
Red
G 9.7 15.5
H 15.5 24.8
I 24.8 39.6
J 39.6 63.4
K 63.4 101.5
L 101.5 162.4
M 162.4 234.6
N 234.6 340.0
O 340.0 540.0
P 540.0 850.0
Q 850.0 1200.0
R 1200.0 1700.0
S 1700.0 2400.0
T 2400.0 3400.0
U 3400.0 4900.0
V 4900.0 7100.0
W 7100.0 10200.0
X 10200.0 14800.0
Y 14800.0 21400.0
Z 21400.0 30900.0
Yellow
F 10.3 16.6
G 16.6 26.5
H 26.5 42.3
I 42.3 67.7
J 67.7 108.2
K 108.2 173.2
L 173.2 250.0
M 250.0 360.0
N 360.0 510.0
O 510.0 800.0
P 800.0 1250.0
Q 1250.0 1800.0
R 1800.0 2900.0
S 2900.0 4700.0
T 4700.0 7200.0
U 7200.0 11700.0
V 11700.0 18000.0
W 18000.0 27000.0
8
Color Categories
Color Category #
Lambda (nm)
Min. Max.
Green
6 561.5 564.5
5 564.5 567.5
4 567.5 570.5
3 570.5 573.5
2 573.5 576.5
Yellow
1 582.0 584.5
3 584.5 587.0
2 587.0 589.5
4 589.5 592.0
5 592.0 593.0
Maximum tolerance for each bin limit is ±0.5 nm.
Mechanical Option Matrix
Mechanical Option Code Denition
00 Bulk Packaging, minimum increment 500 pcs/bag
01 Tape & Reel, crimped leads, minimum increment 1800 pcs/bag
02 Tape & Reel, straight leads, minimum increment 1800 pcs/bag
A1 Right Angle Housing, uneven leads, minimum increment 500 pcs/bag
A2 Right Angle Housing, even leads, minimum increment 500 pcs/bag
Note:
All categories are established for classication of products. Products may not be available in all categories. Please contact your local Avago
representative for further clarication/information.
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved. Obsoletes 5989-4253EN
AV02-1068EN - October 13, 2008
Precautions:
Lead Forming
• The leads of an LED lamp may be preformed or cut to
length prior to insertion and soldering into PC board.
• If lead forming is required before soldering, care must
be taken to avoid any excessive mechanical stress
induced to LED package. Otherwise, cut the leads
of LED to length after soldering process at room
temperature. The solder joint formed will absorb the
mechanical stress of the lead cutting from traveling to
the LED chip die attach and wirebond.
• It is recommended that tooling made to precisely form
and cut the leads to length rather than rely upon hand
operation.
Soldering Conditions
• Care must be taken during PCB assembly and soldering
process to prevent damage to LED component.
• The closest LED is allowed to solder on board is 1.59
mm below the body (encapsulant epoxy) for those
parts without stando.
• Recommended soldering conditions:
• Wave soldering parameter must be set and maintained
according to recommended temperature and dwell
time in the solder wave. Customer is advised to
periodically check on the soldering prole to ensure
the soldering prole used is always conforming to
recommended soldering condition.
• If necessary, use xture to hold the LED component
in proper orientation with respect to the PCB during
soldering process.
• Proper handling is imperative to avoid excessive
thermal stresses to LED components when heated.
Therefore, the soldered PCB must be allowed to cool
to room temperature, 25°C, before handling.
• Special attention must be given to board fabrication,
solder masking, surface plating and lead holes size
and component orientation to assure solderability.
• Recommended PC board plated through hole sizes for
LED component leads:
Manual Solder
Wave Soldering Dipping
Pre-heat Temperature 105°C Max. –
Pre-heat Time 30 sec Max. –
Peak Temperature 250°C Max. 260°C Max.
Dwell Time 3 sec Max. 5 sec Max.
LED Component Plated Through
Lead Size Diagonal Hole Diameter
0.457 x 0.457 mm 0.646 mm 0.976 to 1.078 mm
(0.018 x 0.018 inch) (0.025 inch) (0.038 to 0.042 inch)
0.508 x 0.508 mm 0.718 mm 1.049 to 1.150 mm
(0.020 x 0.020 inch) (0.028 inch) (0.041 to 0.045 inch)
Note: Refer to application note AN1027 for more information on
soldering LED components.
Figure 17. Recommended wave soldering prole.
LAMINAR WAVE BOTTOM SIDE
OF PC BOARD
HOT AIR KNIFE
TURBULENT WAVE
FLUXING
PREHEAT
0 10 20
30
50
100
150
200
250
30 40 50
TIME – SECONDS
TEMPERATURE – °C
60 70 80 90 100
TOP SIDE OF
PC BOARD
CONVEYOR SPEED = 1.83 M/MIN (6 FT/MIN)
PREHEAT SETTING = 150°C (100°C PCB)
SOLDER WAVE TEMPERATURE = 245°C
AIR KNIFE AIR TEMPERATURE = 390°C
AIR KNIFE DISTANCE = 1.91 mm (0.25 IN.)
AIR KNIFE ANGLE = 40
SOLDER: SN63; FLUX: RMA
NOTE: ALLOW FOR BOARDS TO BE
SUFFICIENTLY COOLED BEFORE EXERTING
MECHANICAL FORCE.