MCC ES1A THRU ES1M omponents 21201 Itasca Street Chatsworth !"# $ % !"# Features * * * * * For Surface Mount Applications 1 Amp Super Fast Recovery Silicon Rectifier 50 to 1000 Volts Extremely Low Thermal Resistance Easy Pick And Place High Temp Soldering: 250C for 10 Seconds At Terminals Superfast Recovery Times For High Efficiency Maximum Ratings * * * Operating Temperature: -50C to +150C Storage Temperature: -50C to +150C Maximum Thermal Resistance; 15 C/W Junction To Lead MCC Device Maximum Maximum Maximum Catalog Marking Recurrent RMS DC Number Peak Reverse Voltage Blocking Voltage Voltage ES1A ES1A 50V 35V 50V ES1B ES1B 100V 70V 100V ES1C ES1C 150V 105V 150V ES1D ES1D 200V 140V 200V ES1G ES1G 400V 280V 400V ES1J ES1J 600V 420V 600V ES1K ES1K 800V 560V 800V ES1M ES1M 1000V 700V 1000V DO-214AC (SMAJ) (High Profile) H Cathode Band J A E ES1A-D ES1G-K ES1M Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time ES1A-D ES1G-K ES1M Typical Junction Capacitance IF(AV) 1.0A D G TJ = 75C IFSM 30A 8.3ms, half sine VF .975V 1.35V 1.60V IFM = 1.0A; TJ = 25C* IR 5A 100A TJ = 25C TJ = 100C Trr 50ns 60ns 100ns CJ 45pF IF=0.5A, IR=1.0A, Irr=0.25A Measured at 1.0MHz, VR=4.0V B F Electrical Characteristics @ 25C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage C DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 SUGGESTED SOLDER PAD LAYOUT 0.090" 0.085" *Pulse test: Pulse width 200 sec, Duty cycle 2% www.mccsemi.com 0.070" NOTE MCC ES1A thru ES1M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 2.4 6 2.2 4 2.0 1.8 2 1.6 25C Amps 1.4 1 1.2 .6 Amps .4 1.0 .8 .6 .2 .4 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load .1 .06 0 .04 25 50 75 100 125 150 C Average Forward Rectified Current - Amperesversus Ambient Temperature - C .02 .01 0 .2 .4 .6 .8 1.0 1.2 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pFversus Reverse Voltage - Volts www.mccsemi.com 400 1000 MCC ES1A thru ES1M Figure 4 Peak Forward Surge Current 30 Figure 5 New SMA Assembly 25 20 15 Amps 10 Round Lead Process 5 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50 10 trr +0.5A 0 Pulse Generator Note 2 25Vdc 1 Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com