SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 D D D D D D D D D D D SN54ALVTHR16245 . . . WD PACKAGE SN74ALVTHR16245 . . . DGG, DGV, OR DL PACKAGE (TOP VIEW) State-of-the-Art Advanced BiCMOS Technology (ABT) Widebus Design for 2.5-V and 3.3-V Operation and Low Static-Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 2.3-V to 3.6-V VCC ) Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25C High Drive (-12/12 mA at 3.3-V VCC) Ioff and Power-Up 3-State Support Hot Insertion Use Bus Hold on Data Inputs in Place of External Pullup/Pulldown Resistors to Prevent the Bus From Floating Output Ports Have Equivalent 30- Series Resistors, So No External Resistors Are Required Flow-Through Architecture Facilitates Printed Circuit Board Layout Distributed VCC and GND Pins Minimize High-Speed Switching Noise Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) 1DIR 1B1 1B2 GND 1B3 1B4 VCC 1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCC 2B5 2B6 GND 2B7 2B8 2DIR 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 GND 1A7 1A8 2A1 2A2 GND 2A3 2A4 VCC 2A5 2A6 GND 2A7 2A8 2OE description/ordering information The 'ALVTHR16245 devices are 16-bit (dual-octal) noninverting 3-state transceivers designed for 2.5-V or 3.3-V VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. ORDERING INFORMATION TA -40C 40C to 85C ORDERABLE PART NUMBER PACKAGE TOP-SIDE MARKING SSOP - DL Tape and reel SN74ALVTHR16245LR ALVTHR16245 TSSOP - DGG Tape and reel SN74ALVTHR16245GR ALVTHR16245 TVSOP - DGV Tape and reel SN74ALVTHR16245VR TR245 VFBGA - GQL Tape and reel SN74ALVTHR16245KR TR245 -55C to 125C CFP - WD Tube SNJ54ALVTHR16245W SNJ54ALVTHR16245W Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright 2002, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 description/ordering information (continued) These devices can be used as two 8-bit transceivers or one 16-bit transceiver. They allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so that the buses are effectively isolated. All outputs are designed to sink up to 12 mA, and include equivalent 30- resistors to reduce overshoot and undershoot. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. When VCC is between 0 and 1.2 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.2 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. SN74ALVTHR16245 . . . GQL PACKAGE (TOP VIEW) 1 2 3 4 5 6 terminal assignments 1 2 3 4 5 6 A A 1DIR NC NC NC NC 1OE B B 1B2 1B1 GND GND 1A1 1A2 C C 1B4 1B3 1A4 1B6 1B5 VCC GND 1A3 D VCC GND 1A5 1A6 E 1B8 1B7 1A7 1A8 F 2B1 2B2 2A2 2A1 G 2B3 2B4 GND GND 2A4 2A3 H 2B5 2B6 2A5 2B7 2B8 VCC GND 2A6 J VCC GND 2A8 2A7 2DIR NC NC NC NC 2OE D E F G H J K K NC - No internal connection FUNCTION TABLE (each 8-bit section) INPUTS 2 OPERATION OE DIR L L B data to A bus L H A data to B bus H X Isolation POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 logic diagram (positive logic) 1DIR 1 2DIR 48 1A1 25 1OE 47 2A1 2 24 2OE 36 13 1B1 To Seven Other Channels 2B1 To Seven Other Channels Pin numbers shown are for the DGG, DGV, DL, and WD packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO (see Note 1) . . . . . . . . . -0.5 V to 7 V Output current in the low state, IO: SN54ALVTHR16245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ALVTHR16245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Output current in the high state, IO: SN54ALVTHR16245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -48 mA SN74ALVTHR16245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -64 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Package thermal impedance, JA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63C/W GQL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 recommended operating conditions, VCC = 2.5 V 0.2 V (see Note 3) SN54ALVTHR16245 MIN VCC VIH Supply voltage 2.3 High-level input voltage 1.7 VIL VI Low-level input voltage IOH IOL High-level output current t/v Input transition rise or fall rate TYP SN74ALVTHR16245 MAX MIN 2.7 2.3 TYP 2.7 1.7 0 VCC 5.5 Low-level output current Outputs enabled 0.7 0 UNIT V V 0.7 Input voltage MAX VCC V 5.5 V -6 -8 mA 6 12 mA 10 10 ns/V t/VCC Power-up ramp rate 200 200 s/V TA Operating free-air temperature -55 125 -40 85 C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. recommended operating conditions, VCC = 3.3 V 0.3 V (see Note 3) SN54ALVTHR16245 MIN VCC VIH Supply voltage 3 High-level input voltage 2 VIL VI Low-level input voltage IOH IOL High-level output current t/v Input transition rise or fall rate t/VCC TA Power-up ramp rate 200 Operating free-air temperature -55 TYP SN74ALVTHR16245 MAX MIN 3.6 3 TYP 3.6 2 0 Low-level output current Outputs enabled VCC 5.5 0.8 0 UNIT V V 0.8 Input voltage MAX VCC V 5.5 V -8 -12 mA 8 12 mA 10 10 ns/V s/V 200 125 -40 85 C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 2.5 V 0.2 V (unless otherwise noted) PARAMETER VIK VOH VCC = 2.3 V, VCC = 2.3 V to 2.7 V, II = -18 mA IOH = -100 A 3V VCC = 2 2.3 IOH = -6 mA IOH = -8 mA VCC = 2.3 V to 2.7 V, VOL SN54ALVTHR16245 MIN TYP MAX TEST CONDITIONS VCC = 2 2.3 3V -1.2 VCC-0.2 1.7 1.7 IOL = 12 mA VI = VCC or GND 0.7 1 VI = 5.5 V VI = 5.5 V 10 10 20 20 1 1 VI = VCC VI = 0 VCC = 0, VCC = 2.3 V, VI or VO = 0 to 4.5 V VI = 0.7 V VCC = 2.3 V, VCC = 2.7 V, VI = 1.7 V VI = 0 to VCC VCC = 2.7 V, VCC = 2.3 V, VI = 0 to VCC VO = 5.5 V -5 A -5 100 115 -10 A 115 A -10 A 300 300 A -300 -300 A IOZ(PU/PD)k VCC 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don't care Outputs high ICC VCC = 2.7 V, IO = 0, VI = VCC or GND Outputs disabled VCC = 2.5 V, VCC = 2.5 V, VI = 2.5 V or 0 VO = 2.5 V or 0 3.5 Ci V 1 VCC = 2.7 V IEX|| 0.2 0.7 A or B ports IBHLO IBHHO# V V 0.2 Control inputs Ioff IBHL IBHH -1.2 UNIT VCC-0.2 IOL = 100 A IOL = 6 mA VCC = 2.7 V, VCC = 0 or 2.7 V, II SN74ALVTHR16245 MIN TYP MAX Outputs low 125 125 A 100 100 A 0.04 0.1 0.04 0.1 2.5 0.04 4.5 2.5 4.5 0.1 0.04 0.1 3.5 mA pF Cio 8 8 pF All typical values are at VCC = 2.5 V, TA = 25C. The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 3.3 V 0.3 V (unless otherwise noted) PARAMETER VIK VOH VCC = 3 V, VCC = 3 V to 3.6 V, II = -18 mA IOH = -100 A VCC = 3 V IOH = -8 mA IOH = -12 mA VCC = 3 V to 3.6 V, VOL SN54ALVTHR16245 MIN TYP MAX TEST CONDITIONS VCC = 3 V -1.2 VCC-0.2 2 2 IOL = 12 mA VI = VCC or GND V 0.8 1 1 VI = 5.5 V VI = 5.5 V 10 10 20 20 1 1 VCC = 3.6 V VI = VCC VI = 0 VCC = 0, VCC = 3 V, VI or VO = 0 to 4.5 V VI = 0.8 V VCC = 3 V, VCC = 3.6 V, VCC = 3.6 V, VCC = 3 V, IEX|| 0.2 0.8 A or B ports IBHLO IBHHO# V V 0.2 Control inputs Ioff IBHL IBHH -1.2 UNIT VCC-0.2 IOL = 100 A IOL = 8 mA VCC = 3.6 V, VCC = 0 or 3.6 V, II SN74ALVTHR16245 MIN TYP MAX -5 A -5 100 A 75 75 A VI = 2 V VI = 0 to VCC -75 -75 A 500 500 A VI = 0 to VCC VO = 5.5 V -500 -500 A IOZ(PU/PD)k VCC 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don't care ICC VCC = 3.6 V, IO = 0, VI = VCC or GND Outputs high 0.07 Outputs low Outputs disabled ICCh VCC = 3 V to 3.6 V, One input at VCC - 0.6 V, Other inputs at VCC or GND Ci VCC = 3.3 V, VCC = 3.3 V, VI = 3.3 V or 0 VO = 3.3 V or 0 125 125 A 100 100 A 0.1 0.07 0.1 3.5 5 3.5 5 0.07 0.1 0.07 0.1 0.4 3.5 0.4 3.5 mA mA pF Cio 8 8 pF All typical values are at VCC = 3.3 V, TA = 25C. The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down h This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 switching characteristics over recommended operating free-air temperature range, CL = 30 pF, VCC = 2.5 V 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B B or A tPZH tPZL OE A or B OE A or B tPHZ tPLZ SN54ALVTHR16245 SN74ALVTHR16245 MIN MAX MIN MAX 0.5 4.3 0.5 4.3 0.5 3.7 0.5 3.7 1.8 5.6 1.8 5.6 1.6 4.7 1.6 4.7 1.7 5 1.7 5 1.4 4.4 1.4 4.4 UNIT ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF, VCC = 3.3 V 0.3 V (unless otherwise noted) (see Figure 2) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B B or A tPZH tPZL OE A or B OE A or B tPHZ tPLZ SN54ALVTHR16245 SN74ALVTHR16245 MIN MAX MIN MAX 0.5 3.7 0.5 3.7 0.5 3.9 0.5 3.9 1.3 5.2 1.3 5.2 1.3 4 1.3 4 2 5.1 2 5.1 1.5 4.8 1.5 4.8 UNIT ns ns ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN54ALVTHR16245, SN74ALVTHR16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES075D - JUNE 1996 - REVISED DECEMBER 2002 PARAMETER MEASUREMENT INFORMATION 2 x VCC S1 RL From Output Under Test Open GND CL (see Note A) RL TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 x VCC GND CL 30 pF 50 pF VCC 2.5 V 0.2 V 3.3 V 0.3 V LOAD CIRCUIT V 0.15 V 0.3 V RL 500 500 VCC Timing Input VCC/2 0V tw tsu VCC VCC/2 Input VCC/2 th VCC VCC/2 Data Input VCC/2 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC VCC/2 Input VCC/2 0V tPHL tPLH Output VCC/2 VOL tPHL VCC/2 tPLZ VCC VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + V VOL tPHZ tPZH VCC/2 VCC/2 0V Output Waveform 1 S1 at 2 x VCC (see Note B) tPLH VOH Output VCC/2 tPZL VOH VCC/2 VCC Output Control VCC/2 VOH - V VOH 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2 ns, tf 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 3-May-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTHR16245GRE4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTHR16245GRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTHR16245LRG4 ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTHR16245VRE4 ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTHR16245VRG4 ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTHR16245ZQLR ACTIVE BGA MICROSTAR JUNIOR ZQL 56 1000 Green (RoHS & no Sb/Br) SN74ALVTHR16245DL ACTIVE SSOP DL 48 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTHR16245GR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTHR16245KR LIFEBUY BGA MICROSTAR JUNIOR GQL 56 1000 TBD SN74ALVTHR16245LR ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTHR16245VR ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) SNPB Level-1-260C-UNLIM Level-1-240C-UNLIM The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples (Requires Login) 74ALVTHR16245DLG4 SNAGCU (3) PACKAGE OPTION ADDENDUM www.ti.com 3-May-2012 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN54ALVTHR16245, SN74ALVTHR16245 : * Catalog: SN74ALVTHR16245 * Military: SN54ALVTHR16245 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 74ALVTHR16245ZQLR BGA MI CROSTA R JUNI OR ZQL 56 1000 330.0 16.4 4.8 7.3 1.5 8.0 16.0 Q1 SN74ALVTHR16245GR TSSOP DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1 SN74ALVTHR16245KR BGA MI CROSTA R JUNI OR GQL 56 1000 330.0 16.4 4.8 7.3 1.45 8.0 16.0 Q1 SN74ALVTHR16245LR SSOP DL 48 1000 330.0 32.4 11.35 16.2 3.1 16.0 32.0 Q1 SN74ALVTHR16245VR TVSOP DGV 48 2000 330.0 16.4 7.1 10.2 1.6 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 74ALVTHR16245ZQLR BGA MICROSTAR JUNIOR ZQL 56 1000 333.2 345.9 28.6 SN74ALVTHR16245GR TSSOP DGG 48 2000 367.0 367.0 45.0 SN74ALVTHR16245KR BGA MICROSTAR JUNIOR GQL 56 1000 333.2 345.9 28.6 SN74ALVTHR16245LR SSOP DL 48 1000 367.0 367.0 55.0 SN74ALVTHR16245VR TVSOP DGV 48 2000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA MPDS006C - FEBRUARY 1996 - REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0-8 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins - MO-153 14/16/20/56 Pins - MO-194 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MSSO001C - JANUARY 1995 - REVISED DECEMBER 2001 DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0.025 (0,635) 0.0135 (0,343) 0.008 (0,203) 48 0.005 (0,13) M 25 0.010 (0,25) 0.005 (0,13) 0.299 (7,59) 0.291 (7,39) 0.420 (10,67) 0.395 (10,03) Gage Plane 0.010 (0,25) 1 0-8 24 0.040 (1,02) A 0.020 (0,51) Seating Plane 0.110 (2,79) MAX 0.004 (0,10) 0.008 (0,20) MIN PINS ** 28 48 56 A MAX 0.380 (9,65) 0.630 (16,00) 0.730 (18,54) A MIN 0.370 (9,40) 0.620 (15,75) 0.720 (18,29) DIM 4040048 / E 12/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MO-118 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated