Features * Compatible with MCS-51(R) Products * 4K Bytes of In-System Programmable (ISP) Flash Memory * * * * * * * * * * * * * * * - Endurance: 1000 Write/Erase Cycles 4.0V to 5.5V Operating Range Fully Static Operation: 0 Hz to 33 MHz Three-level Program Memory Lock 128 x 8-bit Internal RAM 32 Programmable I/O Lines Two 16-bit Timer/Counters Six Interrupt Sources Full Duplex UART Serial Channel Low-power Idle and Power-down Modes Interrupt Recovery from Power-down Mode Watchdog Timer Dual Data Pointer Power-off Flag Fast Programming Time Flexible ISP Programming (Byte and Page Mode) Description The AT89S51 is a low-power, high-performance CMOS 8-bit microcontroller with 4K bytes of in-system programmable Flash memory. The device is manufactured using Atmel's high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S51 is a powerful microcontroller which provides a highly-flexible and cost-effective solution to many embedded control applications. 8-bit Microcontroller with 4K Bytes In-System Programmable Flash AT89S51 Preliminary The AT89S51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, two 16-bit timer/counters, a fivevector two-level interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89S51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next external interrupt or hardware reset. Rev. 2487A-10/01 1 Pin Configurations PLCC VCC P0.0 (AD0) P0.1 (AD1) P0.2 (AD2) P0.3 (AD3) P0.4 (AD4) P0.5 (AD5) P0.6 (AD6) P0.7 (AD7) EA/VPP ALE/PROG PSEN P2.7 (A15) P2.6 (A14) P2.5 (A13) P2.4 (A12) P2.3 (A11) P2.2 (A10) P2.1 (A9) P2.0 (A8) (MOSI) P1.5 (MISO) P1.6 (SCK) P1.7 RST (RXD) P3.0 NC (TXD) P3.1 (INT0) P3.2 (INT1) P3.3 (T0) P3.4 (T1) P3.5 6 5 4 3 2 1 44 43 42 41 40 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 18 19 20 21 22 23 24 25 26 27 28 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P0.4 (AD4) P0.5 (AD5) P0.6 (AD6) P0.7 (AD7) EA/VPP NC ALE/PROG PSEN P2.7 (A15) P2.6 (A14) P2.5 (A13) (WR) P3.6 (RD) P3.7 XTAL2 XTAL1 GND NC (A8) P2.0 (A9) P2.1 (A10) P2.2 (A11) P2.3 (A12) P2.4 P1.0 P1.1 P1.2 P1.3 P1.4 (MOSI) P1.5 (MISO) P1.6 (SCK) P1.7 RST (RXD) P3.0 (TXD) P3.1 (INT0) P3.2 (INT1) P3.3 (T0) P3.4 (T1) P3.5 (WR) P3.6 (RD) P3.7 XTAL2 XTAL1 GND P1.4 P1.3 P1.2 P1.1 P1.0 NC VCC P0.0 (AD0) P0.1 (AD1) P0.2 (AD2) P0.3 (AD3) PDIP 44 43 42 41 40 39 38 37 36 35 34 P1.4 P1.3 P1.2 P1.1 P1.0 NC VCC P0.0 (AD0) P0.1 (AD1) P0.2 (AD2) P0.3 (AD3) TQFP 33 32 31 30 29 28 27 26 25 24 23 1 2 3 4 5 6 7 8 9 10 11 P0.4 (AD4) P0.5 (AD5) P0.6 (AD6) P0.7 (AD7) EA/VPP NC ALE/PROG PSEN P2.7 (A15) P2.6 (A14) P2.5 (A13) (WR) P3.6 (RD) P3.7 XTAL2 XTAL1 GND GND (A8) P2.0 (A9) P2.1 (A10) P2.2 (A11) P2.3 (A12) P2.4 12 13 14 15 16 17 18 19 20 21 22 (MOSI) P1.5 (MISO) P1.6 (SCK) P1.7 RST (RXD) P3.0 NC (TXD) P3.1 (INT0) P3.2 (INT1) P3.3 (T0) P3.4 (T1) P3.5 2 AT89S51 2487A-10/01 AT89S51 Block Diagram P0.0 - P0.7 P2.0 - P2.7 PORT 0 DRIVERS PORT 2 DRIVERS VCC GND RAM ADDR. REGISTER B REGISTER PORT 0 LATCH RAM PORT 2 LATCH FLASH PROGRAM ADDRESS REGISTER STACK POINTER ACC BUFFER TMP2 TMP1 PC INCREMENTER ALU INTERRUPT, SERIAL PORT, AND TIMER BLOCKS PROGRAM COUNTER PSW PSEN ALE/PROG EA / VPP TIMING AND CONTROL INSTRUCTION REGISTER DUAL DPTR RST WATCH DOG PORT 3 LATCH PORT 1 LATCH ISP PORT PROGRAM LOGIC OSC PORT 3 DRIVERS P3.0 - P3.7 PORT 1 DRIVERS P1.0 - P1.7 3 2487A-10/01 Pin Description VCC Supply voltage. GND Ground. Port 0 Port 0 is an 8-bit open drain bidirectional I/O port. As an output port, each pin can sink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs. Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses to external program and data memory. In this mode, P0 has internal pull-ups. Port 0 also receives the code bytes during Flash programming and outputs the code bytes during program verification. External pull-ups are required during program verification. Port 1 Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. Port 1 also receives the low-order address bytes during Flash programming and verification. Port 2 Port Pin Alternate Functions P1.5 MOSI (used for In-System Programming) P1.6 MISO (used for In-System Programming) P1.7 SCK (used for In-System Programming) Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @ DPTR). In this application, Port 2 uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order address bits and some control signals during Flash programming and verification. Port 3 Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pull-ups. Port 3 receives some control signals for Flash programming and verification. Port 3 also serves the functions of various special features of the AT89S51, as shown in the following table. 4 AT89S51 2487A-10/01 AT89S51 Port Pin Alternate Functions P3.0 RXD (serial input port) P3.1 TXD (serial output port) P3.2 INT0 (external interrupt 0) P3.3 INT1 (external interrupt 1) P3.4 T0 (timer 0 external input) P3.5 T1 (timer 1 external input) P3.6 WR (external data memory write strobe) P3.7 RD (external data memory read strobe) RST Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device. This pin drives High for 98 oscillator periods after the Watchdog times out. The DISRTO bit in SFR AUXR (address 8EH) can be used to disable this feature. In the default state of bit DISRTO, the RESET HIGH out feature is enabled. ALE/PROG Address Latch Enable (ALE) is an output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during Flash programming. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external data memory. If desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution mode. PSEN Program Store Enable (PSEN) is the read strobe to external program memory. When the AT89S51 is executing code from external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. EA/VPP External Access Enable. EA must be strapped to GND in order to enable the device to fetch code from external program memory locations starting at 0000H up to FFFFH. Note, however, that if lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to VCC for internal program executions. This pin also receives the 12-volt programming enable voltage (V PP ) during Flash programming. XTAL1 Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting oscillator amplifier 5 2487A-10/01 Special Function Registers A map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 1. Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. Table 1. AT89S51 SFR Map and Reset Values 0F8H 0F0H 0FFH B 00000000 0F7H 0E8H 0E0H 0EFH ACC 00000000 0E7H 0D8H 0D0H 6 0DFH PSW 00000000 0D7H 0C8H 0CFH 0C0H 0C7H 0B8H IP XX000000 0BFH 0B0H P3 11111111 0B7H 0A8H IE 0X000000 0AFH 0A0H P2 11111111 98H SCON 00000000 90H P1 11111111 88H TCON 00000000 TMOD 00000000 TL0 00000000 TL1 00000000 TH0 00000000 TH1 00000000 80H P0 11111111 SP 00000111 DP0L 00000000 DP0H 00000000 DP1L 00000000 DP1H 00000000 AUXR1 XXXXXXX0 WDTRST XXXXXXXX 0A7H SBUF XXXXXXXX 9FH 97H AUXR XXX00XX0 8FH PCON 0XXX0000 87H AT89S51 2487A-10/01 AT89S51 User software should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In that case, the reset or inactive values of the new bits will always be 0. Interrupt Registers: The individual interrupt enable bits are in the IE register. Two priorities can be set for each of the five interrupt sources in the IP register. Table 2. AUXR: Auxiliary Register AUXR Address = 8EH Reset Value = XXX00XX0B Not Bit Addressable Bit - - - WDIDLE DISRTO - - DISALE 7 6 5 4 3 2 1 0 - Reserved for future expansion DISALE Disable/Enable ALE DISALE Operating Mode DISRTO 0 ALE is emitted at a constant rate of 1/6 the oscillator frequency 1 ALE is active only during a MOVX or MOVC instruction Disable/Enable Reset out DISRTO WDIDLE 0 Reset pin is driven High after WDT times out 1 Reset pin is input only Disable/Enable WDT in IDLE mode WDIDLE 0 WDT continues to count in IDLE mode 1 WDT halts counting in IDLE mode Dual Data Pointer Registers: To facilitate accessing both internal and external data memory, two banks of 16-bit Data Pointer Registers are provided: DP0 at SFR address locations 82H83H and DP1 at 84H-85H. Bit DPS = 0 in SFR AUXR1 selects DP0 and DPS = 1 selects DP1. The user should always initialize the DPS bit to the appropriate value before accessing the respective Data Pointer Register. 7 2487A-10/01 Power Off Flag: The Power Off Flag (POF) is located at bit 4 (PCON.4) in the PCON SFR. POF is set to "1" during power up. It can be set and rest under software control and is not affected by reset. Table 3. AUXR1: Auxiliary Register 1 AUXR1 Address = A2H Reset Value = XXXXXXX0B Not Bit Addressable Bit - - - - - - - DPS 7 6 5 4 3 2 1 0 - Reserved for future expansion DPS Data Pointer Register Select DPS 0 Selects DPTR Registers DP0L, DP0H 1 Selects DPTR Registers DP1L, DP1H Memory Organization MCS-51 devices have a separate address space for Program and Data Memory. Up to 64K bytes each of external Program and Data Memory can be addressed. Program Memory If the EA pin is connected to GND, all program fetches are directed to external memory. On the AT89S51, if EA is connected to VCC, program fetches to addresses 0000H through FFFH are directed to internal memory and fetches to addresses 1000H through FFFFH are directed to external memory. Data Memory The AT89S51 implements 128 bytes of on-chip RAM. The 128 bytes are accessible via direct and indirect addressing modes. Stack operations are examples of indirect addressing, so the 128 bytes of data RAM are available as stack space. Watchdog Timer (One-time Enabled with Reset-out) The WDT is intended as a recovery method in situations where the CPU may be subjected to software upsets. The WDT consists of a 14-bit counter and the Watchdog Timer Reset (WDTRST) SFR. The WDT is defaulted to disable from exiting reset. To enable the WDT, a user must write 01EH and 0E1H in sequence to the WDTRST register (SFR location 0A6H). When the WDT is enabled, it will increment every machine cycle while the oscillator is running. The WDT timeout period is dependent on the external clock frequency. There is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will drive an output RESET HIGH pulse at the RST pin. Using the WDT To enable the WDT, a user must write 01EH and 0E1H in sequence to the WDTRST register (SFR location 0A6H). When the WDT is enabled, the user needs to service it by writing 01EH and 0E1H to WDTRST to avoid a WDT overflow. The 14-bit counter overflows when it reaches 16383 (3FFFH), and this will reset the device. When the WDT is enabled, it will increment every machine cycle while the oscillator is running. This means the user must reset the WDT at least every 16383 machine cycles. To reset the WDT the user must write 01EH and 0E1H to WDTRST. WDTRST is a write-only register. The WDT counter cannot be read or written. When WDT overflows, it will generate an output RESET pulse at the RST pin. The RESET pulse duration is 98xTOSC, where TOSC=1/FOSC. To make the best use of the WDT, it 8 AT89S51 2487A-10/01 AT89S51 should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset. WDT During Power-down and Idle In Power-down mode the oscillator stops, which means the WDT also stops. While in Powerdown mode, the user does not need to service the WDT. There are two methods of exiting Power-down mode: by a hardware reset or via a level-activated external interrupt, which is enabled prior to entering Power-down mode. When Power-down is exited with hardware reset, servicing the WDT should occur as it normally does whenever the AT89S51 is reset. Exiting Power-down with an interrupt is significantly different. The interrupt is held low long enough for the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the WDT from resetting the device while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service for the interrupt used to exit Power-down mode. To ensure that the WDT does not overflow within a few states of exiting Power-down, it is best to reset the WDT just before entering Power-down mode. Before going into the IDLE mode, the WDIDLE bit in SFR AUXR is used to determine whether the WDT continues to count if enabled. The WDT keeps counting during IDLE (WDIDLE bit = 0) as the default state. To prevent the WDT from resetting the AT89S51 while in IDLE mode, the user should always set up a timer that will periodically exit IDLE, service the WDT, and reenter IDLE mode. With WDIDLE bit enabled, the WDT will stop to count in IDLE mode and resumes the count upon exit from IDLE. UART The UART in the AT89S51 operates the same way as the UART in the AT89C51. For further information on the UART operation, refer to the ATMEL Web site (http://www.atmel.com). From the home page, select `Products', then `8051-Architecture Flash Microcontroller', then `Product Overview'. Timer 0 and 1 Timer 0 and Timer 1 in the AT89S51 operate the same way as Timer 0 and Timer 1 in the AT89C51. For further information on the timers' operation, refer to the ATMEL Web site (http://www.atmel.com). From the home page, select `Products', then `8051-Architecture Flash Microcontroller', then `Product Overview'. Interrupts The AT89S51 has a total of five interrupt vectors: two external interrupts (INT0 and INT1), two timer interrupts (Timers 0 and 1), and the serial port interrupt. These interrupts are all shown in Figure 1. Each of these interrupt sources can be individually enabled or disabled by setting or clearing a bit in Special Function Register IE. IE also contains a global disable bit, EA, which disables all interrupts at once. Note that Table 4 shows that bit position IE.6 is unimplemented. In the AT89S51, bit position IE.5 is also unimplemented. User software should not write 1s to these bit positions, since they may be used in future AT89 products. The Timer 0 and Timer 1 flags, TF0 and TF1, are set at S5P2 of the cycle in which the timers overflow. The values are then polled by the circuitry in the next cycle 9 2487A-10/01 . Table 4. Interrupt Enable (IE) Register (MSB) EA (LSB) - - ES ET1 EX1 ET0 EX0 Enable Bit = 1 enables the interrupt. Enable Bit = 0 disables the interrupt. Symbol Position Function EA IE.7 Disables all interrupts. If EA = 0, no interrupt is acknowledged. If EA = 1, each interrupt source is individually enabled or disabled by setting or clearing its enable bit. - IE.6 Reserved - IE.5 Reserved ES IE.4 Serial Port interrupt enable bit ET1 IE.3 Timer 1 interrupt enable bit EX1 IE.2 External interrupt 1 enable bit ET0 IE.1 Timer 0 interrupt enable bit EX0 IE.0 External interrupt 0 enable bit User software should never write 1s to reserved bits, because they may be used in future AT89 products. Figure 1. Interrupt Sources 0 INT0 IE0 1 TF0 0 INT1 IE1 1 TF1 TI RI 10 AT89S51 2487A-10/01 AT89S51 Oscillator Characteristics XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier that can be configured for use as an on-chip oscillator, as shown in Figure 2. Either a quartz crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven, as shown in Figure 3. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed. Figure 2. Oscillator Connections C2 XTAL2 C1 XTAL1 GND Note: C1, C2 = 30 pF 10 pF for Crystals = 40 pF 10 pF for Ceramic Resonators Figure 3. External Clock Drive Configuration NC XTAL2 EXTERNAL OSCILLATOR SIGNAL XTAL1 GND Idle Mode In idle mode, the CPU puts itself to sleep while all the on-chip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special function registers remain unchanged during this mode. The idle mode can be terminated by any enabled interrupt or by a hardware reset. Note that when idle mode is terminated by a hardware reset, the device normally resumes program execution from where it left off, up to two machine cycles before the internal reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a port pin when idle mode is terminated by a reset, the instruction following the one that invokes idle mode should not write to a port pin or to external memory. Power-down Mode In the Power-down mode, the oscillator is stopped, and the instruction that invokes Powerdown is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the Power-down mode is terminated. Exit from Power-down mode can be initiated either by a hardware reset or by activation of an enabled external interrupt into INT0 or INT1. Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize. 11 2487A-10/01 Table 5. Status of External Pins During Idle and Power-down Modes Program Memory Lock Bits Mode Program Memory ALE PSEN PORT0 PORT1 PORT2 PORT3 Idle Internal 1 1 Data Data Data Data Idle External 1 1 Float Data Address Data Power-down Internal 0 0 Data Data Data Data Power-down External 0 0 Float Data Data Data The AT89S51 has three lock bits that can be left unprogrammed (U) or can be programmed (P) to obtain the additional features listed in the following table. Table 6. Lock Bit Protection Modes Program Lock Bits LB1 LB2 LB3 Protection Type 1 U U U No program lock features 2 P U U MOVC instructions executed from external program memory are disabled from fetching code bytes from internal memory, EA is sampled and latched on reset, and further programming of the Flash memory is disabled 3 P P U Same as mode 2, but verify is also disabled 4 P P P Same as mode 3, but external execution is also disabled When lock bit 1 is programmed, the logic level at the EA pin is sampled and latched during reset. If the device is powered up without a reset, the latch initializes to a random value and holds that value until reset is activated. The latched value of EA must agree with the current logic level at that pin in order for the device to function properly. Programming the Flash - Parallel Mode The AT89S51 is shipped with the on-chip Flash memory array ready to be programmed. The programming interface needs a high-voltage (12-volt) program enable signal and is compatible with conventional third-party Flash or EPROM programmers. The AT89S51 code memory array is programmed byte-by-byte. Programming Algorithm: Before programming the AT89S51, the address, data, and control signals should be set up according to the Flash programming mode table and Figures 13 and 14. To program the AT89S51, take the following steps: 1. Input the desired memory location on the address lines. 2. Input the appropriate data byte on the data lines. 3. Activate the correct combination of control signals. 4. Raise EA/VPP to 12V. 5. Pulse ALE/PROG once to program a byte in the Flash array or the lock bits. The bytewrite cycle is self-timed and typically takes no more than 50 s. Repeat steps 1 through 5, changing the address and data for the entire array or until the end of the object file is reached. Data Polling: The AT89S51 features Data Polling to indicate the end of a byte write cycle. During a write cycle, an attempted read of the last byte written will result in the complement of the written data on P0.7. Once the write cycle has been completed, true data is valid on all outputs, and the next cycle may begin. Data Polling may begin any time after a write cycle has been initiated. 12 AT89S51 2487A-10/01 AT89S51 Ready/Busy: The progress of byte programming can also be monitored by the RDY/BSY output signal. P3.0 is pulled low after ALE goes high during programming to indicate BUSY. P3.0 is pulled high again when programming is done to indicate READY. Program Verify: If lock bits LB1 and LB2 have not been programmed, the programmed code data can be read back via the address and data lines for verification. The status of the individual lock bits can be verified directly by reading them back. Reading the Signature Bytes: The signature bytes are read by the same procedure as a normal verification of locations 000H, 100H, and 200H, except that P3.6 and P3.7 must be pulled to a logic low. The values returned are as follows. (000H) = 1EH indicates manufactured by Atmel (100H) = 51H indicates 89S51 (200H) = 06H Chip Erase: In the parallel programming mode, a chip erase operation is initiated by using the proper combination of control signals and by pulsing ALE/PROG low for a duration of 200 ns 500 ns. In the serial programming mode, a chip erase operation is initiated by issuing the Chip Erase instruction. In this mode, chip erase is self-timed and takes about 500 ms. During chip erase, a serial read from any address location will return 00H at the data output. Programming the Flash - Serial Mode The Code memory array can be programmed using the serial ISP interface while RST is pulled to VCC. The serial interface consists of pins SCK, MOSI (input) and MISO (output). After RST is set high, the Programming Enable instruction needs to be executed first before other operations can be executed. Before a reprogramming sequence can occur, a Chip Erase operation is required. The Chip Erase operation turns the content of every memory location in the Code array into FFH. Either an external system clock can be supplied at pin XTAL1 or a crystal needs to be connected across pins XTAL1 and XTAL2. The maximum serial clock (SCK) frequency should be less than 1/16 of the crystal frequency. With a 33 MHz oscillator clock, the maximum SCK frequency is 2 MHz. Serial Programming Algorithm To program and verify the AT89S51 in the serial programming mode, the following sequence is recommended: 1. Power-up sequence: Apply power between VCC and GND pins. Set RST pin to "H". If a crystal is not connected across pins XTAL1 and XTAL2, apply a 3 MHz to 33 MHz clock to XTAL1 pin and wait for at least 10 milliseconds. 2. Enable serial programming by sending the Programming Enable serial instruction to pin MOSI/P1.5. The frequency of the shift clock supplied at pin SCK/P1.7 needs to be less than the CPU clock at XTAL1 divided by 16. 3. The Code array is programmed one byte at a time in either the Byte or Page mode. The write cycle is self-timed and typically takes less than 0.5 ms at 5V. 4. Any memory location can be verified by using the Read instruction that returns the content at the selected address at serial output MISO/P1.6. 5. At the end of a programming session, RST can be set low to commence normal device operation. 13 2487A-10/01 Power-off sequence (if needed): Set XTAL1 to "L" (if a crystal is not used). Set RST to "L". Turn VCC power off. Data Polling: The Data Polling feature is also available in the serial mode. In this mode, during a write cycle an attempted read of the last byte written will result in the complement of the MSB of the serial output byte on MISO. Serial Programming Instruction Set The Instruction Set for Serial Programming follows a 4-byte protocol and is shown in Table 8 on page 18. Programming Interface - Parallel Mode Every code byte in the Flash array can be programmed by using the appropriate combination of control signals. The write operation cycle is self-timed and once initiated, will automatically time itself to completion. All major programming vendors offer worldwide support for the Atmel microcontroller series. Please contact your local programming vendor for the appropriate software revision. Table 7. Flash Programming Modes Mode VCC RST PSEN Write Code Data 5V H L Read Code Data 5V H L P2.3-0 P1.7-0 ALE/ EA/ PROG VPP P2.6 P2.7 P3.3 P3.6 P3.7 Data 12V L H H H H DIN A11-8 A7-0 H L L L H H DOUT A11-8 A7-0 12V H H H H H X X X 12V H H H L L X X X 12V H L H H L X X X H H H L H L X X 12V H L H L L X X X P0.7-0 Address (2) H (3) Write Lock Bit 1 5V H L Write Lock Bit 2 5V H L Write Lock Bit 3 5V H L 5V H L Chip Erase 5V H L Read Atmel ID 5V H L H H L L L L L 1EH 0000 00H Read Device ID 5V H L H H L L L L L 51H 0001 00H Read Device ID 5V H L H H L L L L L 06H 0010 00H (3) (3) Read Lock Bits 1, 2, 3 H P0.2, P0.3, P0.4 (1) Notes: 14 1. 2. 3. 4. 5. Each PROG pulse is 200 ns - 500 ns for Chip Erase. Each PROG pulse is 200 ns - 500 ns for Write Code Data. Each PROG pulse is 200 ns - 500 ns for Write Lock Bits. RDY/BSY signal is output on P3.0 during programming. X = don't care. AT89S51 2487A-10/01 AT89S51 Figure 4. Programming the Flash Memory (Parallel Mode) VCC AT89S51 A0 - A7 ADDR. 0000H/FFFH A8 - A11 VCC P1.0-P1.7 P2.0 - P2.3 P2.6 P2.7 P3.3 P3.6 SEE FLASH PROGRAMMING MODES TABLE PGM DATA P0 ALE PROG EA VIH/VPP P3.7 XTAL2 3-33 MHz P3.0 RDY/ BSY RST VIH XTAL1 GND PSEN Figure 5. Verifying the Flash Memory (Parallel Mode) VCC AT89S51 A0 - A7 ADDR. 0000H/FFFH A8 - A11 SEE FLASH PROGRAMMING MODES TABLE P1.0-P1.7 VCC P2.0 - P2.3 P0 P2.6 P2.7 P3.3 P3.6 P3.7 PGM DATA (USE 10K PULLUPS) ALE VIH XTAL 2 EA XTAL1 RST 3-33 MHz GND VIH PSEN 15 2487A-10/01 Flash Programming and Verification Characteristics (Parallel Mode) TA = 20C to 30C, VCC = 4.5 to 5.5V Symbol Parameter Min Max Units VPP Programming Supply Voltage 11.5 12.5 V IPP Programming Supply Current 10 mA ICC VCC Supply Current 30 mA 1/tCLCL Oscillator Frequency 33 MHz tAVGL Address Setup to PROG Low 48tCLCL tGHAX Address Hold After PROG 48tCLCL tDVGL Data Setup to PROG Low 48tCLCL tGHDX Data Hold After PROG 48tCLCL tEHSH P2.7 (ENABLE) High to VPP 48tCLCL tSHGL VPP Setup to PROG Low 10 s tGHSL VPP Hold After PROG 10 s tGLGH PROG Width 0.2 tAVQV Address to Data Valid 48tCLCL tELQV ENABLE Low to Data Valid 48tCLCL tEHQZ Data Float After ENABLE tGHBL PROG High to BUSY Low 1.0 s tWC Byte Write Cycle Time 50 s 3 1 0 s 48tCLCL Figure 6. Flash Programming and Verification Waveforms - Parallel Mode PROGRAMMING ADDRESS P1.0 - P1.7 P2.0 - P2.3 VERIFICATION ADDRESS tAVQV PORT 0 DATA IN tAVGL tDVGL tGHDX DATA OUT tGHAX ALE/PROG tSHGL tGLGH VPP tGHSL LOGIC 1 LOGIC 0 EA/VPP tEHSH tEHQZ tELQV P2.7 (ENABLE) tGHBL P3.0 (RDY/BSY) BUSY READY tWC 16 AT89S51 2487A-10/01 AT89S51 Figure 7. Flash Memory Serial Downloading VCC AT89S51 VCC INSTRUCTION INPUT P1.5/MOSI DATA OUTPUT P1.6/MISO P1.7/SCK CLOCK IN XTAL2 3-33 MHz XTAL1 VIH RST GND Flash Programming and Verification Waveforms - Serial Mode Figure 8. Serial Programming Waveforms 7 6 5 4 3 2 1 0 17 2487A-10/01 Table 8. Serial Programming Instruction Set Instruction Format Byte 4 Operation Programming Enable 1010 1100 0101 0011 xxxx xxxx xxxx xxxx 0110 1001 (Output) Enable Serial Programming while RST is high Chip Erase 1010 1100 100x xxxx xxxx xxxx xxxx xxxx Chip Erase Flash memory array Read Program Memory (Byte Mode) 0010 0000 xxxx Write Program Memory (Byte Mode) 0100 0000 xxxx Write Lock Bits(2) 1010 1100 1110 00 Read Lock Bits 0010 0100 xxxx xxxx Read Signature Bytes(1) 0010 1000 xxx Read Program Memory (Page Mode) 0011 0000 xxxx Write Program Memory (Page Mode) 0101 0000 xxxx Notes: A7 A6 A5 A4 A3 A2 A1 A0 Read data from Program memory in the byte mode Write data to Program memory in the byte mode xxxx xxxx Write Lock bits. See Note (2). xxxx xxxx xx Read back current status of the lock bits (a programmed lock bit reads back as a "1") LB2 LB1 xx Byte 0 Byte 1... Byte 255 Read data from Program memory in the Page Mode (256 bytes) Byte 0 Byte 1... Byte 255 Write data to Program memory in the Page Mode (256 bytes) A0 Read Signature Byte A5 A4 A3 A2 A1 Signature Byte A11 A10 A9 A8 xxx xxxx LB3 xxxx xxxx A11 A10 A9 A8 B1 B2 A11 A10 A9 A8 D7 D6 D5 D4 D3 D2 D1 D0 Byte 3 D7 D6 D5 D4 D3 D2 D1 D0 Byte 2 A7 A6 A5 A4 A3 A2 A1 A0 Byte 1 A11 A10 A9 A8 Instruction 1. The signature bytes are not readable in Lock Bit Modes 3 and 4. 2. B1 = 0, B2 = 0 Mode 1, no lock protection Each of the lock bits needs to be activated sequentially before B1 = 0, B2 = 1 Mode 2, lock bit 1 activated Mode 4 can be executed. B1 = 1, B2 = 0 Mode 3, lock bit 2 activated B1 = 1, B1 = 1 Mode 4, lock bit 3 activated } After Reset signal is high, SCK should be low for at least 64 system clocks before it goes high to clock in the enable data bytes. No pulsing of Reset signal is necessary. SCK should be no faster than 1/16 of the system clock at XTAL1. For Page Read/Write, the data always starts from byte 0 to 255. After the command byte and upper address byte are latched, each byte thereafter is treated as data until all 256 bytes are shifted in/out. Then the next instruction will be ready to be decoded. 18 AT89S51 2487A-10/01 AT89S51 Serial Programming Characteristics Figure 9. Serial Programming Timing MOSI tOVSH SCK tSHOX tSLSH tSHSL MISO tSLIV Table 9. Serial Programming Characteristics, TA = -40C to 85C, VCC = 4.0 - 5.5V (Unless Otherwise Noted) Symbol Parameter Min 1/tCLCL Oscillator Frequency 0 tCLCL Oscillator Period 30 ns tSHSL SCK Pulse Width High 8 tCLCL ns tSLSH SCK Pulse Width Low 8 tCLCL ns tOVSH MOSI Setup to SCK High tCLCL ns tSHOX MOSI Hold after SCK High 2 tCLCL ns tSLIV SCK Low to MISO Valid tERASE Chip Erase Instruction Cycle Time tSWC Serial Byte Write Cycle Time 10 Typ 16 Max Units 33 MHz 32 ns 500 ms 64 tCLCL + 400 s 19 2487A-10/01 Absolute Maximum Ratings* Operating Temperature.................................. -55C to +125C *NOTICE: Storage Temperature ..................................... -65C to +150C Voltage on Any Pin with Respect to Ground .....................................-1.0V to +7.0V Maximum Operating Voltage ............................................ 6.6V Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Output Current...................................................... 15.0 mA DC Characteristics The values shown in this table are valid for TA = -40C to 85C and VCC = 4.0V to 5.5V, unless otherwise noted. Symbol Parameter Condition VIL Input Low Voltage (Except EA) VIL1 Input Low Voltage (EA) VIH Input High Voltage (Except XTAL1, RST) VIH1 Input High Voltage (XTAL1, RST) VOL Output Low Voltage(1) (Ports 1,2,3) Min Output Low Voltage (Port 0, ALE, PSEN) -0.5 0.2 VCC-0.1 V 0.2 VCC-0.3 V 0.2 VCC+0.9 VCC+0.5 V 0.7 VCC VCC+0.5 V 0.45 V 0.45 V IOL = 1.6 mA IOL = 3.2 mA IOH = -60 A, VCC = 5V 10% VOH Output High Voltage (Ports 1,2,3, ALE, PSEN) Units -0.5 (1) VOL1 Max 2.4 V IOH = -25 A 0.75 VCC V IOH = -10 A 0.9 VCC V 2.4 V IOH = -800 A, VCC = 5V 10% IOH = -300 A 0.75 VCC V VOH1 Output High Voltage (Port 0 in External Bus Mode) IOH = -80 A 0.9 VCC V IIL Logical 0 Input Current (Ports 1,2,3) VIN = 0.45V ITL Logical 1 to 0 Transition Current (Ports 1,2,3) VIN = 2V, VCC = 5V 10% ILI Input Leakage Current (Port 0, EA) 0.45 < VIN < VCC RRST Reset Pulldown Resistor CIO Pin Capacitance Power Supply Current ICC Notes: 20 Power-down Mode (2) -50 A -650 A 10 A 300 K Test Freq. = 1 MHz, TA = 25C 10 pF Active Mode, 12 MHz 25 mA Idle Mode, 12 MHz 6.5 mA VCC = 5.5V 50 A 50 1. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA Ports 1, 2, 3: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 2. Minimum VCC for Power-down is 2V. AT89S51 2487A-10/01 AT89S51 AC Characteristics Under operating conditions, load capacitance for Port 0, ALE/PROG, and PSEN = 100 pF; load capacitance for all other outputs = 80 pF. External Program and Data Memory Characteristics 12 MHz Oscillator Variable Oscillator Min Min Max Units 0 33 MHz Symbol Parameter Max 1/tCLCL Oscillator Frequency tLHLL ALE Pulse Width 127 2tCLCL-40 ns tAVLL Address Valid to ALE Low 43 tCLCL-25 ns tLLAX Address Hold After ALE Low 48 tCLCL-25 ns tLLIV ALE Low to Valid Instruction In tLLPL ALE Low to PSEN Low 43 tCLCL-25 ns tPLPH PSEN Pulse Width 205 3tCLCL-45 ns tPLIV PSEN Low to Valid Instruction In tPXIX Input Instruction Hold After PSEN tPXIZ Input Instruction Float After PSEN tPXAV PSEN to Address Valid tAVIV Address to Valid Instruction In 312 5tCLCL-80 ns tPLAZ PSEN Low to Address Float 10 10 ns tRLRH RD Pulse Width 400 6tCLCL-100 ns tWLWH WR Pulse Width 400 6tCLCL-100 ns tRLDV RD Low to Valid Data In tRHDX Data Hold After RD tRHDZ Data Float After RD 97 2tCLCL-28 ns tLLDV ALE Low to Valid Data In 517 8tCLCL-150 ns tAVDV Address to Valid Data In 585 9tCLCL-165 ns tLLWL ALE Low to RD or WR Low 200 3tCLCL+50 ns tAVWL Address to RD or WR Low 203 4tCLCL-75 ns tQVWX Data Valid to WR Transition 23 tCLCL-30 ns tQVWH Data Valid to WR High 433 7tCLCL-130 ns tWHQX Data Hold After WR 33 tCLCL-25 ns tRLAZ RD Low to Address Float tWHLH RD or WR High to ALE High 233 4tCLCL-65 145 0 3tCLCL-60 0 59 75 tCLCL-8 0 5tCLCL-90 3tCLCL-50 0 43 123 tCLCL-25 ns ns 0 300 ns ns tCLCL-25 252 ns ns ns 0 ns tCLCL+25 ns 21 2487A-10/01 External Program Memory Read Cycle tLHLL ALE tAVLL tLLIV tLLPL tPLIV PSEN tPXAV tPLAZ tPXIZ tLLAX tPXIX A0 - A7 PORT 0 tPLPH INSTR IN A0 - A7 tAVIV A8 - A15 PORT 2 A8 - A15 External Data Memory Read Cycle tLHLL ALE tWHLH PSEN tLLDV tRLRH tLLWL RD tLLAX tAVLL PORT 0 tRLDV tRLAZ A0 - A7 FROM RI OR DPL tRHDZ tRHDX DATA IN A0 - A7 FROM PCL INSTR IN tAVWL tAVDV PORT 2 22 P2.0 - P2.7 OR A8 - A15 FROM DPH A8 - A15 FROM PCH AT89S51 2487A-10/01 AT89S51 External Data Memory Write Cycle tLHLL ALE tWHLH PSEN tLLWL WR tAVLL tLLAX tQVWX A0 - A7 FROM RI OR DPL PORT 0 tWLWH tQVWH DATA OUT tWHQX A0 - A7 FROM PCL INSTR IN tAVWL PORT 2 P2.0 - P2.7 OR A8 - A15 FROM DPH A8 - A15 FROM PCH External Clock Drive Waveforms tCHCX VCC - 0.5V tCHCX tCLCH tCHCL 0.7 VCC 0.2 VCC - 0.1V 0.45V tCLCX tCLCL External Clock Drive Symbol Parameter Min Max Units 1/tCLCL Oscillator Frequency 0 33 MHz tCLCL Clock Period 30 ns tCHCX High Time 12 ns tCLCX Low Time 12 ns tCLCH Rise Time 5 ns tCHCL Fall Time 5 ns 23 2487A-10/01 Serial Port Timing: Shift Register Mode Test Conditions The values in this table are valid for VCC = 4.0V to 5.5V and Load Capacitance = 80 pF. 12 MHz Osc Variable Oscillator Symbol Parameter Min Max Min Max tXLXL Serial Port Clock Cycle Time 1.0 12tCLCL s tQVXH Output Data Setup to Clock Rising Edge 700 10tCLCL-133 ns tXHQX Output Data Hold After Clock Rising Edge 50 2tCLCL-80 ns tXHDX Input Data Hold After Clock Rising Edge 0 0 ns tXHDV Clock Rising Edge to Input Data Valid 700 10tCLCL-133 Units ns Shift Register Mode Timing Waveforms INSTRUCTION ALE 0 1 2 3 4 5 6 7 8 tXLXL CLOCK tQVXH tXHQX WRITE TO SBUF 0 1 2 tXHDV OUTPUT DATA CLEAR RI 3 4 5 6 tXHDX VALID VALID VALID 7 SET TI VALID VALID VALID VALID VALID SET RI INPUT DATA AC Testing Input/Output Waveforms(1) VCC - 0.5V 0.2 VCC + 0.9V TEST POINTS 0.2 VCC - 0.1V 0.45V Note: 1. AC Inputs during testing are driven at VCC - 0.5V for a logic 1 and 0.45V for a logic 0. Timing measurements are made at VIH min. for a logic 1 and VIL max. for a logic 0. Float Waveforms(1) V LOAD+ 0.1V V LOAD - 24 0.1V V OL + 0.1V Timing Reference Points V LOAD Note: V OL - 0.1V 1. For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to float when a 100 mV change from the loaded VOH/VOL level occurs. AT89S51 2487A-10/01 AT89S51 Ordering Information Speed (MHz) Power Supply 24 4.0V to 5.5V 33 4.5V to 5.5V Ordering Code Package Operation Range AT89S51-24AC AT89S51-24JC AT89S51-24PC 44A 44J 40P6 Commercial (0C to 70C) AT89S51-24AI AT89S51-24JI AT89S51-24PI 44A 44J 40P6 Industrial (-40C to 85C) AT89S51-33AC AT89S51-33JC AT89S51-33PC 44A 44J 40P6 Commercial (0C to 70C) = Preliminary Availability Package Type 44A 44-lead, Thin Plastic Gull Wing Quad Flatpack (TQFP) 44J 44-lead, Plastic J-leaded Chip Carrier (PLCC) 40P6 40-pin, 0.600" Wide, Plastic Dual Inline Package (PDIP) 25 2487A-10/01 Packaging Information 44A, 44-lead, Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) Dimensions in Millimeters and (Inches)* 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) .045(1.14) X 45 12.21(0.478) SQ 11.75(0.458) PIN 1 ID 0.45(0.018) 0.30(0.012) 0.80(0.031) BSC PIN NO. 1 IDENTIFY .045(1.14) X 30 - 45 .032(.813) .026(.660) .695(17.7) SQ .685(17.4) .500(12.7) REF SQ .021(.533) .013(.330) .043(1.09) .020(.508) .120(3.05) .090(2.29) .180(4.57) .165(4.19) 1.20(0.047) MAX 0 7 0.20(.008) 0.09(.003) .630(16.0) .590(15.0) .656(16.7) SQ .650(16.5) .050(1.27) TYP 10.10(0.394) SQ 9.90(0.386) .012(.305) .008(.203) .022(.559) X 45 MAX (3X) 0.75(0.030) 0.45(0.018) 0.15(0.006) 0.05(0.002) *Controlling dimension: millimeters 40P6, 40-pin, 0.600" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-011 AC 2.07(52.6) 2.04(51.8) PIN 1 .566(14.4) .530(13.5) .090(2.29) MAX 1.900(48.26) REF .220(5.59) MAX .005(.127) MIN SEATING PLANE .065(1.65) .015(.381) .022(.559) .014(.356) .161(4.09) .125(3.18) .110(2.79) .090(2.29) .012(.305) .008(.203) 26 .065(1.65) .041(1.04) .630(16.0) .590(15.0) 0 REF 15 .690(17.5) .610(15.5) AT89S51 2487A-10/01 Atmel Headquarters Atmel Product Operations Corporate Headquarters Atmel Colorado Springs 2325 Orchard Parkway San Jose, CA 95131 TEL (408) 441-0311 FAX (408) 487-2600 Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL (719) 576-3300 FAX (719) 540-1759 Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-7658-3000 FAX (33) 4-7658-3480 Atmel Heilbronn Theresienstrasse 2 POB 3535 D-74025 Heilbronn, Germany TEL (49) 71 31 67 25 94 FAX (49) 71 31 67 24 23 Atmel Nantes La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 0 2 40 18 18 18 FAX (33) 0 2 40 18 19 60 Atmel Rousset Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-4253-6000 FAX (33) 4-4253-6001 Atmel Smart Card ICs Scottish Enterprise Technology Park East Kilbride, Scotland G75 0QR TEL (44) 1355-357-000 FAX (44) 1355-242-743 e-mail literature@atmel.com Web Site http://www.atmel.com (c) Atmel Corporation 2001. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. ATMEL (R) is the registered trademark of Atmel. MCS-51 (R) is the registered trademark of Intel Corporation. Terms and product names in this document may be trademarks of others. Printed on recycled paper. 2487A-10/01/xM