611252-ENV 1 2 3 4 5 6 7 8 9 10 11 12 B D369 - H P 3 3 - N P 1 HARSH ENVIRONMENT (OMIT FOR CABIN VARIANT 2 CONTACT TYPE (P=PIN, S=SKT) ) 12.85 MAX. 4 CONTACT CONFIGURATION SHELL KEYING SHELL SIZE (3, 6 OR 9) 2.50 MIN. SLOT D1 BOEING PART NUMBER EXAMPLE: C BACC65CP 1 P N BASIC PART NUMBER SHELL KEY SHELL SIZE (1=SIZE 3, 2=SIZE 6, 3=SIZE 9) CONTACT TYPE (PIN=PIN, S=SKT) 0.35 MAX. BUTTON DEPRESSED POSITION C D2 -X +X A 'CABIN' CONNECTOR 'HARSH ENVIRONMENT' CONNECTOR D369-P**-*** D369-HP**-*** OR BACC65CP*** 1500VRMS <2mA LEAKAGE DURABILITY 500 MATING CYCLES MIN. INSULATION RESISTANCE 5000 M INITIAL 9.89 MAX. -55 C TO +175 C TEMPERATURE RANGE DIELECTRIC WITHSTAND VOLTAGE (AT SEA LEVEL) IP RATING SEALING IP65 RTCA DO160 - CATEGORY A4 (15,000ft) IP67 EN2591-314: 12.1kPa (1.75psi) @ 15km (50,000ft) HUMIDITY RTCA DO160 - CATEGORY A EN2591-321 / EIA-364-31 METHOD IV D COORDINATE POSITIONS OF CONTACTS (3 WAY CONNECTOR ONLY) CONTACT POSITION (ID) 1 2 3 1 INSERTION / EXTRACTION TOOL (M81969/14-01 OR EQUIVALENT) SUPPLIED SEPARATELY. 4 CONTACT P/N (OR EQUIVALENT) CONTACT DESCRIPTION PIN SOCKET PIN 0 G CRIMP POSITIONER SOCKET CRIMP TOOL WIRE ACCOMODATION CURRENT RATING M22520/2-01 22-28 AWG 5A (22 AWG) ALNP 22-A 22 AWG 5A M22520/2-01 20-24 AWG 5A (20 AWG) H 1 CRIMP, COPPER WIRE 38941-22L 38946-22L 2 CRIMP, ALUMINIUM WIRE 200-1042-22 200-1142-22 3 CRIMP, ENLARGED COPPER WIRE 182-0860-22 182-0862-22 M22520/2-09 E 0 0 0 F M22520/2-06 KAL2 M22520/2-09 M22520/2-06 G PIN / MALE CONTACT CAVITY IDENTIFICATION ON REAR COMPONENT MATERIAL (FINISH: CLEAN IN ALL CASES) SEALS SILICONE / FLUOROSILICONE BLEND RUBBER BODY / INSERT COMPONENTS THERMOPLASTIC IF FILLER PLUGS ARE REQUIRED, USE THE FOLLOWING: TE PART NUMBER - 600300-22. MIL-SPEC PART NUMBER - MS27488-22-2. 7. MAXIMUM WEIGHTS (WITHOUT CONTACTS): 3 WAY - 1.9g (PIN INSERT), 2.0g (SOCKET INSERT). 6 WAY - 2.4g (PIN INSERT), 2.6g (SOCKET INSERT). 9 WAY - 3.0g (PIN INSERT), 3.2g (SOCKET INSERT). H 4.12 3.50 (SOCKET INSERT) SHELL COLOUR IS KEYING DEPENDANT (SEE TABLE) J ACCESSORY OR BOOT MOUNTING FEATURE 8 FOR ALL 'HARSH ENVIRONMENT' VARIANTS, THE REAR BODY IS TO BE COLOURED DARK BLUE. 9 DIMENSIONS ARE TRUE POSITIONS OF CAVITIES AT FRONT OF PIN INSERT (SOCKET OPPOSITE). CENTRE OF EACH CAVITY 0.20 A B . ORIENTATION COLOUR N A B C D BLACK DARK RED DARK BLUE DARK GREEN YELLOW POSITIONS (0.03) D1 D2 -2.35 2.90 -2.35 -2.90 -1.175 -2.90 0 -2.90 1.175 -2.90 REAR WIRE SEAL 8 REAR BODY L BS8888 THIRD ANGLE PROJECTION UNLESS OTHERWISE STATED: DIMENSIONS: mm [INCHES] AB DUK-70190 JCB RJM NDL CEO 04/02/2019 ISSUE CHANGE NOTE DRAWN CHECKED APP. ENG. APP. MARKETING DATE 2 4 5 6 7 8 9 10 MATERIAL: IF IN DOUBT, ASK 11 12 13 FINISH: SEE NOTES TITLE: TYPE: CUSTOMER DRAWING 369 PLUG CONNECTOR, ENVELOPE DRAWING SIZE: IF IN DOUBT, ASK 3 K SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR CABLE TIE SLOT SHELL KEYING (ALL SIZES) 1 -2.54 0 2.54 NO CONTACTS SUPPLIED 6. L CONTACT LOCATION X AXIS (mm) Y AXIS (mm) PART MARKING MATERIALS: 5. 9 9.35 8.67 (PIN INSERT) CONTACT CONFIGURATION: CONFIG. THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). -Y SHELL TO SHELL ALIGNMENT RIBS D369-P33-NP1 K1316 H++++D 3. M +Y PERFORMANCE: E K B MARKED ON BAG ONLY BOEING PART STANDARD BACC65CP REVISION 'B' REFERS. N.B. BACC65CP*** PART NUMBERS ARE SUPPLIED WITHOUT CONTACTS. 2 B 10.40 MAX. (BUTTON) CONTACT QUANTITY (3=3 x #22, 6=6 x #22, 9=9 x #22) J A 24.86 MAX. BASIC PART NUMBER SHELL STYLE (P=PLUG) F 16 1.05 MIN. SLOT PART NUMBER EXAMPLE: D 15 MARKED WITH TE PART NUMBER, CAGE CODE AND DATE CODE. 4.75 MAX. DRAWING NUMBER: 14 3 WAY CONNECTOR NOTES: 1 13 SCALE: A1 5:1 14 DRAWING NUMBER: 611252-ENV 15 TE CONNECTIVITY UK LTD., ST. LEONARDS-ON-SEA, TN38 9RF, UK. SHEET: 1 OF 2 16 ISSUE: AB M 2 3 611252-ENV 1 24.86 MAX. B 2.50 MIN. SLOT 4 5 7 8 9 10 11 12 13 -X B 12.95 MAX. (BUTTON) 7.29 MAX. 15.50 MAX. (BUTTON) -Y 0.35 MAX. BUTTON DEPRESSED POSITION +X C +Y -Y SHELL TO SHELL ALIGNMENT RIBS D2 -X D +X A A 1 2 3 4 5 6 7 8 9 PART MARKING 4.12 3.50 (SOCKET INSERT) 9.89 MAX. CONTACT POSITION (ID) 9 CONTACT LOCATION X AXIS (mm) Y AXIS (mm) -2.54 2.54 0 2.54 2.54 2.54 2.54 0 0 0 -2.54 0 -2.54 -2.54 0 -2.54 2.54 -2.54 COORDINATE POSITIONS OF CONTACTS (6 WAY CONNECTOR ONLY) D369-P66-NP1 K1316 H++++D 9.89 MAX. 1.05 MIN. SLOT 1.05. MIN. SLOT DRAWING NUMBER: 9.83 MAX. +Y B D1 B COORDINATE POSITIONS OF CONTACTS (9 WAY CONNECTOR ONLY) 1 12.85 MAX. 2.50 MIN. SLOT D2 D369-P99-NP1 K1316 H++++D F 16 24.86 MAX. D1 0.35 MAX. BUTTON DEPRESSED POSITION E 15 6 WAY CONNECTOR 12.85 MAX. D 14 A 9 WAY CONNECTOR C THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). 6 CONTACT POSITION (ID) 1 1 2 3 4 5 6 PART MARKING 9 E CONTACT LOCATION X AXIS (mm) Y AXIS (mm) -2.54 1.27 0 1.27 2.54 1.27 2.54 -1.27 0 -1.27 -2.54 -1.27 F 4.12 3.50 (SOCKET INSERT) G G H H SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR 9.35 8.67 (PIN INSERT) 9.35 8.67 (PIN INSERT) J J SOCKET / FEMALE CONTACT CAVITY IDENTIFICATION ON REAR K K PIN / MALE CONTACT CAVITY IDENTIFICATION ON REAR L L BS8888 THIRD ANGLE PROJECTION PIN / MALE CONTACT CAVITY IDENTIFICATION ON REAR UNLESS OTHERWISE STATED: DIMENSIONS: mm [INCHES] MATERIAL: SEE NOTES TITLE: TYPE: CUSTOMER DRAWING 369 PLUG CONNECTOR, ENVELOPE DRAWING SIZE: M IF IN DOUBT, ASK 1 2 3 4 5 6 7 8 9 10 11 12 13 FINISH: SCALE: A1 5:1 14 DRAWING NUMBER: 611252-ENV 15 TE CONNECTIVITY UK LTD., ST. LEONARDS-ON-SEA, TN38 9RF, UK. SHEET: 2 OF 2 16 ISSUE: AB M