APL5301/2 Low IQ, Low Dropout 300mA Fixed Voltage Regulator Features * * * * * Low Noise : 60uVRMS (100Hz to 100kHz) Low Quiescent Current : 50uA (No load) Low Dropout Voltage : 400mV (VOUT(Nominal)=3.0V Version @300mA) Very low Shutdown Current : < 0.5uA Fixed Output Voltage : 1.3V ~ 5.0V by step 0.1V increment Stable with 1uF Output Capacitor Stable with Aluminum, Tantalum or Ceramic Capacitors . Reverse Current Protection No Protection Diodes Needed * Built in Thermal Protection * * * * * Built in Current Limit Protection Controlled Short Circuit Current : 50mA Fast Transient Response Short Setting Time SOP-8, SOT-23, SOT-23-5, SOT-89, and SOT-89-5 Packages * * * * The APL5301/2 series are micropower, low noise, low dropout linear regulators, which operate from 3V to 6V input voltage and deliver up to 300mA. Typical output noise is just 60uVRMS with the addition of an external 0.33uF bypass capacitor in BP pin and typical dropout voltage is only 260mV at 300mA loading. Designed for use in battery-powered system, the low 50uA quiescent current makes it an ideal choice. Design with an internal P-channel MOSFET pass transistor, the APL5301/2 maintain a low supply current, independent of the load current and dropout voltage. Other features include reverse current protection, thermal-shutdown protection, current limit protection to ensure specified output current and controlled shortcircuit current. The APL5301/2 regulators come in a miniature SOP-8, SOT-23, SOT-23-5, SOT-89 and SOT-89-5 packages. Pin Configuration V IN 3 Applications * * * T A B is V IN 1 2 1 2 G ND V OUT GND V IN SOT-23 (Top View) APL5301 Notebook Computer PDA or Portable Equipments Noise-Sensitive Instrumentation Systems 1 GND 2 V IN 3 APL5301 5 BP 4 SHDN GND SHDN 5 1 4 2 V O UT G N D SOT-23-5 (Top View) APL5301 V OUT SOT-89 (Top View) BP V OUT 3 3 V IN SOT-89-5 (Top View) APL5301 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.9 -Apr., 2003 1 www.anpec.com.tw APL5301/2 Pin Configuration (Cont.) G ND 1 8 GND V IN 2 7 GND V OUT 3 6 GND BP 4 5 GND SHDN T A B is G N D V IN 1 GND 2 SHDN 3 5 V OUT 3 SOP-8 (Top View) 1 2 V OUT V IN SOT-23 (Top View) APL5301 4 1 2 3 V OUT GND V IN BP SOT-23-5 (Top View) SOT-89 (Top View) APL5302 APL5302 APL5302 Ordering and Marking Information Package C ode A : S O T -23 B : S O T -2 3-5 D 5 : S O T -89-5 K : S O P -8 T e m p . R a nge C : 0 to 70 C I : -40 to 8 5 C H andling C ode T R : T ap e & R ee l V o ltage C ode : 13 : 1 .3V ~ 3 4 : 3.4V 5 0 : 5.0V A P L5 30 1/2 H andling C ode T e m p . R a nge Package C ode V o ltage C ode A P L53 01/2 -13 D /K : A P L 5 3 0 1 /2 XXXXX 13 XXXXX - D ate C o de ; D : S O T -89 13 - 1.3V Marking Information SOT-23 and SOT-23-5 packages Product Name APL5301-13A/B APL5301-14A/B APL5301-15A/B APL5301-16A/B APL5301-17A/B APL5301-18A/B APL5301-19A/B APL5301-20A/B APL5301-21A/B APL5301-22A/B APL5301-23A/B APL5301-24A/B APL5301-25A/B APL5301-26A/B APL5301-27A/B APL5301-28A/B APL5301-29A/B APL5301-30A/B APL5301-31A/B Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 Marking 317X 318X 319X 31AX 31BX 31CX 31DX 31EX 31FX 31GX 31HX 31IX 31JX 31KX 31LX 31MX 31NX 31OX 31PX Product Name APL5302-13A/B APL5302-14A/B APL5302-15A/B APL5302-16A/B APL5302-17A/B APL5302-18A/B APL5302-19A/B APL5302-20A/B APL5302-21A/B APL5302-22A/B APL5302-23A/B APL5302-24A/B APL5302-25A/B APL5302-26A/B APL5302-27A/B APL5302-28A/B APL5302-29A/B APL5302-30A/B APL5302-31A/B 2 Marking 327X 328X 329X 32AX 32BX 32CX 32DX 32EX 32FX 32GX 32HX 32IX 32JX 32KX 32LX 32MX 32NX 32OX 32PX www.anpec.com.tw APL5301/2 Marking Information (Cont.) SOT-23 and SOT-23-5 packages Product Name APL5301-32A/B APL5301-33A/B APL5301-34A/B APL5301-35A/B APL5301-48A/B APL5301-49A/B APL5301-50A/B Marking 31QX 31RX 31SX 31TX 31XX 31YX 31ZX Product Name APL5302-32A/B APL5302-33A/B APL5302-34A/B APL5302-35A/B APL5302-48A/B APL5302-49A/B APL5302-50A/B Marking 32QX 32RX 32SX 32TX 32XX 32YX 32ZX The last character "X" in the marking is for data code. Pin Description PIN Name VIN No. 1 2 GND 3 4 5 SHDN(Note1) BP(Note1) VOUT I/O I I O O Description Supply voltage input. Ground pins of the circuitry, and all ground pins must be soldered To PCB with proper power dissipation. Shutdown control pin, low = off, high = nromal. Bypass signal pin of the regulator. Output pin of the regulator. Note1 : This pin does not exist in 3-pin package. Absolute Maximum Ratings Symbol VIN, VOUT SHDN RTH,JA Parameter Input Voltage or Out Voltage Shutdown Control Pin Thermal Resistance - Junction to Ambient PD Power Dissipation TJ Operating Junction Temperature Control Section TL 6 V 357 C/W Internally Limited W 0 to 125 Storage Temperature Range Lead Temperature (Soldering, 10 second) Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 Unit V C Power Transistor TSTG Rating 6 3 0 to 150 -65 to +150 C 260 C www.anpec.com.tw APL5301/2 Electrical Characteristics Unless otherwise noted these specifications apply over full temperature, VIN=3.8V, CIN=COUT=1uF, SHDN=VIN, TJ=0 to 125C. Typical values refer to TJ=25C. APL5301/2 Symbol Parameter Test Conditions Unit Min. Typ. Max. VIN Input Voltage 2.7 6 V VOUT+1.0V< VCC<6.0V, 0mA< IOUT VOUT -2% VOUT VOUT +2% VOUT Output Voltage V VINI =VOUT+0.5V ILIMIT Circuit Current Limit 500 mA ISHORT Short Current VOUT=0V 50 mA IOUT Load Current 300 mA VIN=VOUT+0.5V REGLINE Line Regulation VOUT+0.5V< VCC<6.0V, IOUT=150mA 4 10 mV REGLOA Load Regulation VIN =VOUT+0.5V, 0mA< IOUT < IMAX 1 6 mV VIN= VOUT+0.5V , IOUT=1mA150mA in 1us 70 150 mV mV 1.3VVOUT<1.5V 1.5VVOUT<2.0V IOUT =300mA 2.0VVOUT<2.5V 2.5VVOUT<3V 3VVOUT 5V F1kHz, 1Vpp at VIN = VOUT+1.0V 1.2 1 0.8 0.6 0.4 55 1.6 1.2 0.9 0.7 0.5 V No load 50 80 IOUT=300mA 150 180 Shutdown = low IOUT=0, VCC=6.0V 0.01 1 Load Transient VDROP Dropout Voltage(Note2) PSRR Ripple Rejection IQ Quiescent Current Shutdown Supply Current(Note3) Noise OTS TC COUT Shutdown Recovery Delay(Note3) Over Temperature Shutdown 45 100Hz<f<100kHz, typical load, CBP=0.1uF, COUT = 1uF 100Hz<f<100kHz, typical load, CBP=0.33uF, COUT = 1uF CBP=0.1uF,COUT=1uF, no load CBP=0.33uF,COUT=1uF, no load dB A A 80 Vrms 60 4 13.2 150 ms C Over Temperature Shutdown Hysteries Hysteresis 10 C Output Voltage Temperature Coefficient 50 ppm/C Output Capacitor 0.8 1.0 2.6 ESR Shutdown Input Threshold(Note3) 0.02 0.1 1 F Ohm 0.4 1.6 2.5 V Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 VOUT+1.0V< VIN <6.0V 4 www.anpec.com.tw APL5301/2 Electrical Characteristics (Cont.) Symbol ISHDN Parameter Test Conditions Shutdown input Bias current(Note3) Input Reverse Leakage current Reverse Protection Threshold APL5301/2 Min. Unit Typ. Max. VSHDN =VIN 0.01 100 nA VOUT-VIN=0.1V 0.1 0.5 A 11 50 mV Note2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT+ 0.5V Note3 : For 5-pin devices only. Application Circuit IN P U T 2 .7 V to 6 V V IN V OUT VO UT A P L5301/2 C IN 1uF BP SHDN on C OUT 1uF GND off C BP Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 5 0.33uF www.anpec.com.tw APL5301/2 Typical Characteristics (All Curves are For Fix 3.3V) Ground Pin Current vs. Load Current Ground Pin Current vs. Load Current (uA) Output Voltage vs. Temperature 3.31 3.3 3.29 Ground Pin Current vs. Load Current (uA) 3.28 -40 -15 10 35 60 85 160 140 120 100 80 60 40 20 0 0 50 100 150 200 250 Temperature (C ) Load Current (mA) Ground Pin Current vs. Input Voltage Input Voltage vs. Output Voltage 300 3.5 160 IOUT=50mA 140 3 Output Voltage (V) Output Voltage (V) 3.32 120 100 NO LOAD 80 60 40 2.5 2 1.5 1 0.5 20 0 0 0 1 2 3 4 5 0 6 Input Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 1 2 3 4 5 6 Input Voltage (V) 6 www.anpec.com.tw APL5301/2 Typical Characteristics Reverse Leakage Current vs. Output Voltage Dropout Voltage vs. Load Current 1 Reverse Leakage Current (uA) 300 Dropout Voltage (mV) 250 200 150 100 50 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 0 50 100 150 200 250 0 300 2 3 4 Load Current (mA) Output Voltage (V) SHDN Threshold Voltage vs. Input Voltage PSRR vs. Frequency 1.6 5 6 +0 -10 1.5 -20 1.4 PSRR (dB) SHDN Threshold Voltage (V) 1 1.3 1.2 -30 VIN=4.3V IOUT =50mA COUT=1uF CBP=0.1uF -40 -50 -60 1.1 -70 -80 1 3.5 4 4.5 5 5.5 10 6 Input Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 20 50 100 200 500 1k 2k 5k 10k 20k 50k 200k Frequency (HZ) 7 www.anpec.com.tw APL5301/2 Typical Characteristics Output Noise Output Noise vs. Bypass Capacitor 250 300u 250u VOUT (50uV/div) 150u VIN=4.3V f=100HZ-80KH Z IOUT =50mA COUT=1uF CBP=0.33uF VIN=4.3V f=100HZ-80KHZ IOUT=50mA COUT=1uF 200 Output Noise (uV) 200u 100u 50u 0 -50u -100u -150u 150 100 50 -200u -250u -300u 0 0 2m 4m 6m 8m 0 10m 0.1 0.3 Time (s) Bypass Capacitor (uF) Load-Transient Response Line-Transient Response Output Voltage (50mV/div) VIN=4.3V IOUT 50mA 1mA Time (100us) Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 0.4 VOUT VOUT Output Voltage (20mV/div) 0.2 5V 4V IOUT=50mA V IN Time (500us/div) 8 www.anpec.com.tw APL5301/2 Typical Characteristics Shutdown Exit Delay Shutdown Exit Delay 2.5V 2.5V v SHDN v SHDN CBP=0.1uF 0V cBP=0.33uF 0V VOUT VOUT 0V 0V Time (2ms/div) Time (4ms/div) Entering Shutdown Region of Stable ESR vs. Load Current 10 2.5V Stable Region COUT ESR () VSHDN 0V VOUT COUT=1uF 1 0.1 0V 0.01 0 Time (0.1ms/div) Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 50 100 150 200 250 300 Load Current (mA) 9 www.anpec.com.tw APL5301/2 Application Information Capacitor Selection and Regulator Stability Input-Output (Dropout)Voltage The minimum input-output voltage difference (dropout) determines the lowest usable supply voltage. In battery-powered systems, this will determine the useful end-of-life battery voltage. Because the APL5301/2 use a p-channel MOSFET pass transistor, the dropout voltage is a function of drain-to-source on-resistance (RDS(ON)) multiplied by the load current. The APL5301/2 use at least a 1uF capacitor on the input, and this capacitor can be Aluminum, Tantalum or Ceramic capacitor. The input capacitor with larger value and lower ESR provides better PSRR and linetransient response. The output capacitor also can use Aluminum, Tantalum or Ceramic capacitor, and a minimum value of 1uF and ESR above 0.06 is recommended. The curve of the stable region in typical characteristics shows the appropriate output capacitor ESR for different load current stable operation. A larger output capacitor can reduce noise and improve load-transient response, stability, and PSRR. Note that some ceramic dielectrics exhibit large capacitance and ESR variation with temperature. When using this capacitor, a minimum 2.2uF or more may be required to ensure the stability at low temperature operation. Use a bypass capacitor at BP pin for low output nvise. Increasing the capacitance will slightly decrease the output noise, but increase the start-up time. (See Shutdown Exit Delay and Output Noise vs.Bypass Capacitor graph in the typical characteristics) Reverse Current Protection The APL5301/2 have an internal reverse protection, it does not need an external schottky diode to connect the regulator input and output. If the output voltage is forced above the input voltage by more than 11mV, the IC will be shutdown and the ground pin current is below 0.1uA. Current Limit The APL5301/2 have a current limit protection. The ouptut voltage will drop close to zero volt, when load current reaches the limit, and then the load current will be limited at 50mA after output voltage is below 0. 7V. When the load current back to the value where limiting started, the output voltage and current will return to normal value. When output is shorted to ground, the APL5301/2 will keep short circuit current at 150mA . Load-Transient Considerations The APL5301/2 load-transient response graphs in typical characteristics show the transient response. A step change in the load current from 1mA to 50mA at 1us will cause a 60mV transient spike. Larger output capacitor and lower ESR can reduce transient spike. Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 10 www.anpec.com.tw APL5301/2 Thermal Protection Thermal protection limits total power dissipation in the device. When the junction temperature exceeds TJ=+150J, the thermal sensor generates a logic signal to turn off the pass transistor and allows IC to cool. When the IC's junction temperature is down by 10J, the thermal sensor will turn the pass transistor on again, resulting in a pulsed output during continuous thermal protection. Thermal protection is designed to protect the APL5301/2 in the event of fault conditions. For continuous operation, do not exceed the absolute maximum junction temperature of TJ=+150J. Operating Region and Power Dissipation The thermal resistance of the case to circuit board, and the rate of air flow all control the APL5301/2's maximum power dissipation. The power dissipation across the device is PD = IOUT (VIN-VOUT) and the maximum power dissipation is: PDMAX = (TJ-TA) / (? JC + ? CA) where TJ-TA is the temperature difference between the junction and ambient air, ? JC is the thermal resistance of the package, and ? CA is the thermal resistance through the printed circuit board, copper traces, and other materials to the ambient air. The GND pin of the APL5301 and APL5302 that the packages ard SOT-23-5, SOT-89-5 AND SOP-8 provide an electrical connection to ground and channeling heat away. If power dissipation is large, connect the GND pin to ground using a large pad or ground plane, can improve the problem of over heat of IC. Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 11 www.anpec.com.tw APL5301/2 Packaging Information E e1 0.015X45 SOP-8 pin ( Reference JEDEC Registration MS-012) H e2 D A1 1 L 0.004max. Dim A Mi ll im et er s Inche s A Min . 1. 35 Max . 1. 75 Min. 0. 053 Max . 0. 069 A1 D E 0. 10 4. 80 3. 80 0. 25 5. 00 4. 00 0. 004 0. 189 0. 150 0. 010 0. 197 0. 157 H L e1 e2 5. 80 0. 40 0. 33 6. 20 1. 27 0. 51 0. 228 0. 016 0. 013 0. 244 0. 050 0. 020 1 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 1. 27B S C 0. 50B S C 8 8 12 www.anpec.com.tw APL5301/2 Packaging Information SOT-23 D B 3 E H 2 1 S e A L A1 Dim C M illim et er s Inc he s A M in . 1. 0 0 A1 0. 0 0 0. 1 0 0. 0 00 0. 0 04 B 0. 3 5 0. 5 1 0. 0 14 0. 0 20 C 0. 1 0 0. 2 5 0. 0 04 0. 0 10 D 2. 7 0 3. 1 0 0. 1 06 0. 1 22 E 1. 4 0 1. 8 0 0. 0 55 e M ax. 1. 3 0 M in. 0. 0 39 1. 9 0 B SC H 2. 4 0 L 0. 3 7 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 M ax. 0. 0 51 0. 0 71 0. 0 75 B SC 3. 0 0 0. 0 94 0. 11 8 0. 0 01 5 13 www.anpec.com.tw APL5301/2 Packaging Information SOT-23-5 e1 5 4 E1 1 E 3 2 e b D A2 A a A1 Dim A A1 A2 D E E1 L L1 L2 N L2 L Mi ll imet er s Min . 0. 9 5 0. 0 5 0. 9 0 2. 8 2. 6 1. 5 0. 3 5 Inc hes Ma x . 1. 4 5 0. 1 5 1. 3 0 3. 0 0 3. 0 0 1. 7 0 0. 5 5 Min . 0. 0 37 0. 0 02 0. 0 35 0. 11 0 0. 1 02 0. 0 59 0. 0 14 0. 2 0 BSC 0. 5 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 Ma x . 0. 0 57 0. 0 06 0. 0 51 0. 11 8 0. 11 8 0. 0 67 0. 0 22 0. 0 08 B SC 0. 7 0. 0 20 5 0 L1 0. 0 28 5 10 14 0 10 www.anpec.com.tw APL5301/2 Packaging Information SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62) D D1 a E H 1 2 3 L C B1 B e e1 A a D im A B B1 C D D1 e e1 E H L M illim eters M in. 1.40 0.40 0.35 0.35 4.40 1.35 Inches M ax. 1.60 0.56 0.48 0.44 4.60 1.83 M in. 0.055 0.016 0.014 0.014 0.173 0.053 1.50 B SC 3.00 B SC 2.29 3.75 0.80 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 M ax. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 B SC 2.60 4.25 1.20 10 15 0.090 0.148 0.031 0.102 0.167 0.047 10 www.anpec.com.tw APL5301/2 Packaging Information SOT-89-5 Dim A B C D E F G H I J K L M illim eters M in. 4.40 4.05 1.50 1.30 2.40 0.80 Inches M ax. 4.60 4.25 1.70 1.50 2.60 - M in. 0.17 0.16 0.06 0.05 0.09 0.03 3.00 REF 1.50 REF 0.40 1.40 0.35 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 M ax. 0.18 0.17 0.07 0.06 0.1 0.12 REF 0.06 REF 0.52 1.60 0.41 5 TYP 0.01 0.05 0.01 0.02 0.06 0.02 0.2 TYP 16 www.anpec.com.tw APL5301/2 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) temperature Reference JEDEC Standard J-STD-020A APRIL 1999 Peak temperature 183C Pre-heat temperature Time Classification Reflow Profiles Convection or IR/ Convection Average ramp-up rate(183C to Peak) 3C/second max. 120 seconds max Preheat temperature 125 25C) 60 - 150 seconds Temperature maintained above 183C Time within 5C of actual peak temperature 10 -20 seconds Peak temperature range 220 +5/-0C or 235 +5/-0C Ramp-down rate 6 C /second max. 6 minutes max. Time 25C to peak temperature VPR 10 C /second max. 60 seconds 215-219C or 235 +5/-0C 10 C /second max. Package Reflow Conditions pkg. thickness 2.5mm and all bgas Convection 220 +5/-0 C VPR 215-219 C IR/Convection 220 +5/-0 C pkg. thickness < 2.5mm and pkg. volume 350 mm Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 17 pkg. thickness < 2.5mm and pkg. volume < 350mm Convection 235 +5/-0 C VPR 235 +5/-0 C IR/Convection 235 +5/-0 C www.anpec.com.tw APL5301/2 R e lia b ilit y te s t p r o g r a m Te s t ite m S O L D E R A B IL IT Y H O LT PCT TST ESD L a tc h -U p M e th o d M IL -S T D -8 8 3 D -2 0 0 3 M IL -S T D -8 8 3 D -1 0 0 5 .7 J E S D -2 2 - B , A 1 0 2 M IL -S T D -8 8 3 D -1 0 11 .9 M IL -S T D -8 8 3 D -3 0 1 5 .7 JESD 78 D e s c rip tio n 2 45 C , 5 S E C 1 0 0 0 H rs B ia s @ 1 2 5 C 1 6 8 H rs , 1 0 0 % R H , 1 2 1 C -6 5 C ~ 1 5 0 C , 2 0 0 C y c le s V H B M > 2 K V, V M M > 2 0 0 V 1 0 m s , I tr > 1 0 0 m A Carrier Tape t D P Po E P1 Bo F W Ko Ao D1 T2 J C A B T1 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 18 www.anpec.com.tw APL5301/2 Reel Dimensions A p p lic a tion SOP- 8 A B T1 T2 W P E 6 2 + 1.5 C 1 2.7 5+ 0 .1 5 J 3 30 1 2 0 .5 1 2.4 0.2 2 0 .2 12 0. 3 8 0 .1 1 .7 50 .1 F D D1 Po P1 Ao Bo Ko t 0 .3 0 .01 3 5 .5 1 A p p lic a tion S O T-89 A p p lic a tion S O T-23 -5 4 .0 0 .1 2 .0 0 .1 6 .4 0 .1 5 .2 0 . 1 2 .1 0 .1 A B C J T1 T2 P E 1 78 1 70 2 1 3.5 0.15 3 0 .1 5 14 2 1 .3 0 .3 W 1 2 + 0.3 1 2 - 0 .1 8 0 .1 1 .7 5 0 .1 F D D1 Po P1 Ao Bo Ko t 5 .5 0 .05 1 .5 0 .1 1 .5 0 .1 4 .0 0 .1 2 .0 0 .1 4 .8 0 .1 4 .5 0 .1 1 .8 0 0 .1 0 .3 0 .01 3 A B C J T1 T2 P E 1 78 1 7 2 1 .0 8 .4 2 1 .5 0 .3 W 8 .0 + 0.3 - 0.3 4 0 .1 1 .7 5 0 .1 F D D1 Po P1 Ao Bo Ko t 3 .5 0 .05 1 .5 + 0.1 1 .5 + 0.1 4 .0 0 .1 2 .0 0 .1 3 .1 5 0.1 3 .2 0 .1 1 .4 0 .1 0 .2 0 .03 1 .5 5 +0.1 1 .5 5 + 0.2 5 1 3.0 + 0 .2 2 .5 0 .15 Cover Tape Dimensions Application SOP- 8 SOT- 23 SOT- 89 Carrier Width 12 8 12 Cover Tape Width 9.3 5.3 9.3 Devices Per Reel 2500 3000 1000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.9 - Apr., 2003 19 www.anpec.com.tw