ALUMINUM ELECTROLYTIC CAPACITORS
U
1Z
2G
31
4C
51
60
70
8M
9C
10 L
11 1
12 G
13 B
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
Plastic platform
Series
Capacitance
Voltage (C : 16V)
Lot No.
Positive
Negative
X2
10C
ZG
0.3MAX.
3.90 +0.05
–0.2
φD±0.5
B±0.2
C±0.2
0.5MAX.
A±0.3 A±0.3
E
0.5 to 0.8
ZGseries
3.95mmL MAX. Chip Type,
Wide Temperature Range
Chip type with 3.95mmLMAX height. Operating over wide
temperature range of –40
to +105°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
Chip Type Type numbering system (Example : 16V 10
µ
F)
Specifications
φD
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
6.3
2.4
6.6
6.6
2.2
(mm)
Stability at Low
Temperature
Resistance to
soldering heat
Z–40°C / Z+20°C
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Marking
Performance CharacteristicsItem –40 to +105°C
6.3 to 50V
0.1 to 100µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Rated voltage (V)
Rated voltage (V)
tan δ (MAX.)
6.3
0.38
6.3
6
10
10
0.32
10
5
10
16
0.20
16
3
6
25
0.16
25
3
6
35
0.14
35
3
4
50
0.14
50
3
4
120Hz 20°C
120Hz
Impedance ratio
ZT / Z20 (MAX.)
Z–25°C / Z+20°C
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate and
restored to 20°C.
Black print on the case top.
Shelf Life
Endurance The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 105°C.
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Capacitance change
Leakage current
tan δ
Within ±30% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
ZG
ZT
Smaller
Voltage
V 6.3 10 16 25 35 50
Code j A C E V H
Dimensions
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
5
5
6.3
19
26
32
52
6.3
0J 10
1A 16
1C 25
1E 35
1V 50
1H
V
Code
5
5
6.3
24
30
40
4
5
6.3
6.3
16
26
35
44
4
5
6.3
6.3
11
20
33
42
4
5
6.3
13
22
36
4
4
4
4
4
4
4
5
6.3
0.9
2.2
2.8
3.3
5.4
9.6
12.
16.
26.
Rated
ripple
Rated ripple current (mArms) at 105°C 120Hz
Cap. (µF)
Taping specifications are given in page 23.
Recommended land size soldering by reflow are given
in page 18,19.
Please refer to page 3 for the minimum order quantity.
Case size
φD (mm)
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz 120 Hz 300 Hz 1 kHz
10 kHz or more
0.70 1.00 1.17 1.36 1.50
CAT.8100Y
