ALUMINUM ELECTROLYTIC CAPACITORS ZG 3.95mmL MAX. Chip Type, Wide Temperature Range series Chip type with 3.95mmLMAX height. Operating over wide temperature range of - 40 to +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). ZT Smaller ZG Specifications Item Performance Characteristics Category Temperature Range - 40 to +105C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 100F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (A) , whichever is greater. Rated voltage (V) 6.3 10 16 25 35 50 0.38 0.32 0.20 0.16 0.14 0.14 Rated voltage (V) 6.3 10 16 25 35 50 Impedance ratio Z-25C / Z+20C ZT / Z20 (MAX.) Z-40C / Z+20C 6 5 3 3 3 3 10 10 6 6 4 Tangent of loss angle (tan ) tan (MAX.) Stability at Low Temperature 120Hz 20C 120Hz 4 Capacitance change tan Leakage current Within 30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 105C. Shelf Life After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20C. Marking Black print on the case top. Capacitance change tan Leakage current Within 10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 16V 10F) Chip Type Plastic platform 0.3 MAX. Series C0.2 Capacitance 3.90 1 2 3 4 5 6 7 8 9 10 11 12 13 14 U ZG 1 C 1 0 0 MC L 1 GB E B0.2 D0.5 X2 10C ZG Lot No. A0.3 A0.3 Voltage (C : 16V) 0.5 MAX. Positive D A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 Taping code Configuration Capacitance tolerance (20%) Rated capacitance (10F) +0.05 -0.2 V 6.3 10 16 25 35 50 Code j A C E V H Rated voltage (16V) Negative 0.5 to 0.8 Voltage Series name Type Dimensions 6.3 0J V Cap. (F) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 10 1A 19 26 32 52 5 5 6.3 16 1C 24 30 40 4 5 6.3 6.3 25 1E 16 26 35 44 4 5 6.3 6.3 35 1V 11 20 33 42 4 5 6.3 50 1H 13 22 36 4 4 4 4 4 4 4 5 6.3 Case size D (mm) 0.9 2.2 2.8 3.3 5.4 9.6 12. 16. 26. Rated ripple Rated ripple current (mArms) at 105C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size soldering by reflow are given in page 18,19. Please refer to page 3 for the minimum order quantity. CAT.8100Y