88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Doc. No. MV-S105540-00, Rev. A October 10, 2013 Document Classification: Proprietary Information Marvell. Moving Forward Faster 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Document Conventions Note: Provides related information or information of special importance. Caution: Indicates potential damage to hardware or software, or loss of data. Warning: Indicates a risk of personal injury. Document Status Advance Information This document contains design specifications for initial product development. Specifications may change without notice. Contact Marvell Field Application Engineers for more information. Preliminary Information This document contains preliminary data, and a revision of this document will be published at a later date. Specifications may change without notice. Contact Marvell Field Application Engineers for more information. Final Information This document contains specifications on a product that is in final release. Specifications may change without notice. Contact Marvell Field Application Engineers for more information. Doc Status: Technical Publications: 1.10 For more information, visit our website at: www.marvell.com No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of Marvell. Marvell retains the right to make changes to this document at any time, without notice. Marvell makes no warranty of any kind, expressed or implied, with regard to any information contained in this document, including, but not limited to, the implied warranties of merchantability or fitness for any particular purpose. Further, Marvell does not warrant the accuracy or completeness of the information, text, graphics, or other items contained within this document. Marvell products are not designed for use in life-support equipment or applications that would cause a life-threatening situation if any such products failed. Do not use Marvell products in these types of equipment or applications. With respect to the products described herein, the user or recipient, in the absence of appropriate U.S. government authorization, agrees: 1) Not to re-export or release any such information consisting of technology, software or source code controlled for national security reasons by the U.S. Export Control Regulations ("EAR"), to a national of EAR Country Groups D:1 or E:2;2) Not to export the direct product of such technology or such software, to EAR Country Groups D:1 or E:2, if such technology or software and direct products thereof are controlled for national security reasons by the EAR; and, 3) In the case of technology controlled for national security reasons under the EAR where the direct product of the technology is a complete plant or component of a plant, not to export to EAR Country Groups D:1 or E:2 the direct product of the plant or major component thereof, if such direct product is controlled for national security reasons by the EAR, or is subject to controls under the U.S. Munitions List ("USML"). At all times hereunder, the recipient of any such information agrees that they shall be deemed to have manually signed this document in connection with their receipt of any such information. Copyright (c) 1999-2013. Marvell International Ltd. All rights reserved. Alaska, ARMADA, CarrierSpan, Kinoma, Link Street, LinkCrypt, Marvell logo, Marvell, Moving Forward Faster, PISC, Prestera, Qdeo (for chips), QDEO logo (for chips), QuietVideo, Virtual Cable Tester, Xelerated, and Yukon are registered trademarks of Marvell or its affiliates. Avanta, Avastar, DragonFly, HyperDuo, Kirkwood, Marvell Smart, Qdeo, QDEO logo, The World as YOU See It, Vmeta and Wirespeed by Design are trademarks of Marvell or its affiliates. Patent(s) Pending--Products identified in this document may be covered by one or more Marvell patents and/or patent applications. Doc. No. MV-S105540-00 Rev. A Page 2 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver O VERVIEW F EATURES (R) The Alaska Ultra 88E1111 Gigabit Ethernet Transceiver is a physical layer device for Ethernet 1000BASE-T, 100BASE-TX, and 10BASE-T applications. It is manufactured using standard digital CMOS process and contains all the active circuitry required to implement the physical layer functions to transmit and receive data on standard CAT 5 unshielded twisted pair. * 10/100/1000BASE-T IEEE 802.3 compliant * Supports GMII, TBI, reduced pin count GMII (RGMII), reduced pin count TBI (RTBI), and serial GMII (SGMII) interfaces * Integrated 1.25 GHz SERDES for 1000BASE-X fiber applications The 88E1111 device incorporates the Marvell Virtual Cable Tester(R) (VCTTM) feature, which uses Time Domain Reflectometry (TDR) technology for the remote identification of potential cable malfunctions, thus reducing equipment returns and service calls. Using VCT, the Alaska 88E1111 device detects and reports potential cabling issues such as pair swaps, pair polarity and excessive pair skew. The device will also detect cable opens, shorts or any impedance mismatch in the cable and report accurately within one meter the distance to the fault. * Four RGMII timing modes * Energy Detect and Energy Detect+ low power modes * Three loopback modes for diagnostics * "Downshift" mode for two-pair cable installations * Fully integrated digital adaptive equalizers, echo cancellers, and crosstalk cancellers * Advanced digital baseline wander correction The 88E1111 device supports the Gigabit Media Independent Interface (GMII), Reduced GMII (RGMII), Serial Gigabit Media Independent Interface (SGMII), the Ten-Bit Interface (TBI), and Reduced TBI (RTBI) for direct connection to a MAC/Switch port. * Automatic MDI/MDIX crossover at all speeds of operation * Automatic polarity correction * IEEE 802.3u compliant Auto-Negotiation The 88E1111 device incorporates an optional 1.25 GHz SERDES (Serializer/Deserializer). The serial interface may be connected directly to a fiber-optic transceiver for 1000BASE-T/1000BASE-X media conversion applications. Additionally, the 88E1111 device may be used to implement 1000BASE-T Gigabit Interface Converter (GBIC) or Small Form Factor Pluggable (SFP) modules. * Software programmable LED modes including LED testing * Automatic detection of fiber or copper operation * Supports IEEE 1149.1 JTAG * Two-Wire Serial Interface (TWSI) and MDC/MDIO * CRC checker, packet counter * Packet generation * Virtual Cable Tester (VCT) * Auto-Calibration for MAC Interface outputs * Requires only two supplies: 2.5V and 1.0V (with 1.2V option for the 1.0V supply) * I/Os are 3.3V tolerant * Low power dissipation Pave = 0.75W * 117-Pin TFBGA, 96-Pin aQFN, and 128 PQFP package options (NOTE: The 96-Pin BCC package is obsolete and is no longer available. The 96-Pin aQFN package is a pin compatible replacement for the 96-Pin BCC package. See Product Change Notification 1210066 and Table 20 for details.) * 117-Pin TFBGA and 96-Pin aQFN packages available in Commercial or Industrial grade * RoHS 6/6 compliant packages available The 88E1111 device uses advanced mixed-signal processing to perform equalization, echo and crosstalk cancellation, data recovery, and error correction at a gigabit per second data rate. The device achieves robust performance in noisy environments with very low power dissipation. The 88E1111 device is offered in three different package options including a 117-Pin TFBGA, a 96-pin aQFN featuring a body size of only 9 x 9 mm, and a 128 PQFP package. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 3 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver M a g n e t i c s 88E1111 Device 10/100/1000 Mbps Ethernet MAC MAC Interface Options - GMII/MII - TBI - RGMII - RTBI - SGMII - Serial Interface RJ-45 Media Types: - 10BASE-T - 100BASE-TX - 1000BASE-T Fiber Optics Media Types: - 1000BASE-X 88E1111 Device used in Copper Application 88E1111 Device 10/100/1000 Mbps Ethernet MAC Serial Interface MAC Interface Options - GMII/MII - RGMII 88E1111 Device used in Fiber Application (Effective SGMII MAC) Gigabit Ethernet MAC MAC Interface Options - GMII - RGMII 88E1111 Device 3-Speed SFP Serial Interface - 4-pin SGMIII 88E1111 RGMII/GMII MAC to SGMII MAC Conversion Doc. No. MV-S105540-00, Rev. A Page 4 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Table of Contents 1.1 117-Pin TFBGA Package................................................................................................6 1.2 96-Pin aQFN Package ...................................................................................................7 1.3 128-Pin PQFP Package ..................................................................................................9 1.4 Pin Description .............................................................................................................10 1.4.1 Pin Type Definitions.......................................................................................................... 10 1.5 I/O State at Various Test or Reset Modes ..................................................................35 1.6 117-Pin TFBGA Pin Assignment List - Alphabetical by Signal Name .....................36 1.7 96-Pin aQFN Pin Assignment List - Alphabetical by Signal Name ..........................38 1.8 128-Pin PQFP Pin Assignment List - Alphabetical by Signal Name........................40 2.1 117-pin TFBGA Package..............................................................................................42 2.2 96-pin BCC Package - Top View - OBSOLETE - No Longer Available - Replaced by the 96Pin aQFN Package.................................................................................................................44 2.3 96-Pin BCC Package - Bottom View - OBSOLETE - No Longer Available - Replaced by the 96-Pin aQFN Package ...........................................................................................................45 2.4 96-pin aQFN Package - Top View................................................................................46 2.5 96-Pin aQFN Package - Bottom View .........................................................................47 2.6 128-Pin PQFP Package ................................................................................................49 3.1 Ordering Part Numbers and Package Markings........................................................50 3.1.1 3.1.2 3.1.3 RoHS 5/6 Compliant Marking Examples .......................................................................... 51 RoHS 6/6 Compliant Marking Examples .......................................................................... 53 Green Compliant Marking Examples ................................................................................ 55 Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 5 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Section 1. Signal Description The 88E1111 device is a 10/100/1000BASE-T/1000BASE-X Gigabit Ethernet transceiver. 1.1 117-Pin TFBGA Package Figure 1: 88E1111 Device 117-Pin TFBGA Package (Top View) 1 2 3 4 5 6 7 8 9 A RXD5 RXD6 S_IN+ S_IN- S_CLK+ S_CLK- S_OUT+ S_OUT- B RX_DV RXD0 RXD3 VDDO CRS COL AVDD C RX_CLK VDDO RXD2 RXD4 RXD7 DVDD DVDD D TX_CLK RX_ER RXD1 VSS VSS VSS DVDD E TX_EN GTX_CLK DVDD VSS VSS VSS DVDD F TXD0 TX_ER DVDD VSS VSS VSS VDDOH G NC TXD1 TXD2 VSS VSS VSS CONFIG[3] H TXD4 TXD3 TXD5 VSS VSS VSS VSSC J TXD6 TXD7 DVDD VSS VSS VSS DVDD K VDDO 125CLK RESETn VSS VSS VSS L INTn VDDOX MDC COMA VSS M MDIO RSET AVDD AVDD N MDI[0]+ MDI[0]- MDI[1]+ 1 2 3 LED_ LED_ LINK1000 A VDDOH B LED_RX C LED_TX D CONFIG[1] E CONFIG[2] CONFIG[4] F CONFIG[6] CONFIG[5] G XTAL1 H VDDOH XTAL2 J NC TDO VDDOX K VSS TDI TMS TCK L HSDAC+ HSDAC- AVDD AVDD TRSTn M MDI[1]- AVDD MDI[2]+ MDI[2]- MDI[3]+ MDI[3]- N 4 5 6 7 8 9 LINK100 LED_ LINK10 CONFIG[0] LED_ DUPLEX SEL_ FREQ Figure 2: Pin A1 Location Pin A1 location 88E1111-BAB Doc. No. MV-S105540-00, Rev. A Page 6 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description 96-Pin aQFN Package 1.2 96-Pin aQFN Package 50 TDO NC VSSC 52 VDDOH 54 XTAL2 SEL_ FREQ 51 53 55 XTAL1 57 56 DVDD 59 CONFIG[5] 58 CONFIG[6] 61 CONFIG[3] 60 CONFIG[4] 63 DVDD 62 CONFIG[2] 65 CONFIG[0] 64 CONFIG[1] 67 DVDD 69 LED_RX 66 VDDOH 45 MDI[3]- 43 MDI[2]- 41 MDI[2]+ 39 44 MDI[3]+ 42 AVDD 40 HSDAC- 38 AVDD 36 MDI[1]- 34 AVDD 32 RSET 30 37 AVDD 35 MDI[1]+ 33 MDI[0]+ RESETn 28 VDDOX 26 VDDO TX_ER TX_EN TXD0 NC DVDD TXD4 TXD6 VDDO 5 7 9 11 13 15 17 19 21 MDIO RX_ER 3 24 DVDD INTn VDDO AVDD TDI 23 RXD0 O N - 47 MDI[0]- 125CLK 94 RX_DV RXD2 LO TXD7 RXD1 20 92 RXD3 TRSTn 48 HSDAC+ TXD5 RXD4 TXD3 90 RXD5 16 VDDO RXD6 TXD2 88 by LA - CAA I 88E1111 A V A R E G N 14 RXD7 12 86 DVDD - L P RE D E AC 1 O LED_TX 70 CRS 2 96 68 71 LED_DUPL EX DVDD 72 84 TE E L O BS 95 E L B COL TXD1 93 S_IN+ DVDD 91 82 S_IN- 10 89 S_CLK- GTX_CLK 87 80 8 85 S_CLK+ DVDD 83 AVDD 6 81 VSS 18 78 79 0 S_OUT+ 49 46 TMS 4 77 LED_LINK 10 aQ TCK FN 31 29 COMA 27 MDC 25 22 76 n pi 96 VDDOX S_OUT- TX_CLK 75 LED_LINK 100 RX_CLK 74 VDDOH LED_LINK 1000 73 Figure 3: 88E1111 Device 96-Pin BCC Package (Top View) - (OBSOLETE - No Longer Available - Replaced by 96-Pin aQFN Package) Note The 96-Pin aQFN package is a pin compatible replacement for the 96-Pin BCC package. See Product Change Notification 1210066 and Table 20 for details. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 7 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver B35 A27 TDO A28 NC A29 VSSC B24 VDDOH B25 A30 XTAL1 XTAL2 A31 DVDD SEL_ FREQ B26 B27 A32 CONFIG[5] CONFIG[6] A33 CONFIG[3] B28 CONFIG[4] A34 CONFIG[2] DVDD B29 A35 B30 CONFIG[1] CONFIG[0] A36 DVDD VDDOH B31 A37 LED_RX LED_TX B32 A38 DVDD B33 LED_DUPL EX VDDOH B19 CRS HSDAC- B18 MDI[2]- MDI[2]+ HSDAC+ 88E1111 - NDC AVDD B17 VDDO MDI[1]- B16 RXD4 AVDD B15 RXD1 RSET B14 RX_DV RESETn B13 VDDOX B12 RXD7 AVDD MDI[1]+ MDI[0]- MDI[0]+ RXD0 125CLK A25 A24 A23 A22 A21 A20 A19 A18 A17 A16 A15 MDIO A14 A13 INTn MDC A12 B11 TXD7 B10 VDDO A11 A10 TXD6 TXD5 B9 TXD3 TXD4 A9 DVDD A8 B8 TXD2 B7 NC B6 A7 A6 TXD0 TXD1 DVDD B5 B4 TX_EN A5 A4 TX_ER DVDD B3 VDDO B2 TX_CLK A3 A1 RX_ER VDDO GTX_CLK COMA DVDD A52 AVDD RXD2 B44 A51 S_IN+ MDI[3]- RXD3 B43 A50 B20 RXD5 B42 A49 MDI[3]+ RXD6 B41 A48 S_CLK- AVDD DVDD B40 A47 B21 COL B39 A46 TDI S_IN- B38 A45 AVDD S_CLK+ B37 A44 B22 S_OUT+ B36 A43 TMS EPAD - VSS A26 B23 TRSTn LED_LINK 10 A2 A42 TCK VDDOX S_OUT- RX_CLK A41 LED_LINK 100 B1 A40 B34 LED_LINK 1000 A39 Figure 4: 88E1111 Device 96-Pin aQFN Package (Top View) Pin 1 Corner Doc. No. MV-S105540-00, Rev. A Page 8 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description 128-Pin PQFP Package 1.3 128-Pin PQFP Package 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 88E1111 - RCJ Top View 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 AVDD VSS MDI[3]MDI[3]+ VSS AVDD VSS MDI[2]MDI[2]+ VSS HSDACHSDAC+ AVDD VSS NC AVDD VSS MDI[1]MDI[1]+ VSS AVDD VSS MDI[0]MDI[0]+ VSS RSET VSS DVDD RXD0 RX_DV VDDO DVDD RX_CLK RX_ER VSS TX_CLK VDDO DVDD TX_ER GTX_CLK VSS TX_EN DVDD TXD0 TXD1 TXD2 VSS VSS DVDD TXD3 TXD4 TXD5 DVDD TXD6 TXD7 VDDO 125CLK INTn MDIO VDDOX MDC RESETn COMA VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 VSS AVDD S_OUTVSS S_OUT+ VSS S_CLKS_CLK+ VSS S_INS_IN+ COL CRS VSS DVDD DVDD VSS RXD7 RXD6 VDDO RXD5 RXD4 RXD3 RXD2 VSS RXD1 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 VSS VSS LED_LINK10 LED_LINK100 LED_LINK1000 VDDOH DVDD LED_DUPLEX VSS VSS LED_RX LED_TX DVDD VDDOH CONFIG[0] CONFIG[1] CONFIG[2] DVDD VSS VSS CONFIG[3] CONFIG[4] CONFIG[5] CONFIG[6] DVDD SEL_FREQ XTAL1 XTAL2 VSSC VDDOH TDO VDDOX TCK TMS TRSTn TDI VSS VSS Figure 5: 88E1111 Device 128-Pin PQFP Package (Top View) Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 9 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver 1.4 Pin Description 1.4.1 Pin Type Definitions Pi n Ty pe De fin iti on H Input with hysteresis I/O Input and output I Input only O Output only PU Internal pull up PD Internal pull down D Open drain output Z Tri-state output mA DC sink capability Doc. No. MV-S105540-00, Rev. A Page 10 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 1: Media Dependent Interface 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e D escr ip tio n N1 N2 I/O, D Media Dependent Interface[0]. A16 A17 41 42 MDI[0]+ MDI[0]- In 1000BASE-T mode in MDI configuration, MDI[0] correspond to BI_DA. In MDIX configuration, MDI[0] correspond to BI_DB. In 100BASE-TX and 10BASE-T modes in MDI configuration, MDI[0] are used for the transmit pair. In MDIX configuration, MDI[0] are used for the receive pair. MDI[0] should be tied to ground if not used. N3 N4 A18 B16 46 47 MDI[1]+ MDI[1]- I/O, D Media Dependent Interface[1]. In 1000BASE-T mode in MDI configuration, MDI[1] correspond to BI_DB. In MDIX configuration, MDI[1] correspond to BI_DA. In 100BASE-TX and 10BASE-T modes in MDI configuration, MDI[1] are used for the receive pair. In MDIX configuration, MDI[1] are used for the transmit pair. MDI[1] should be tied to ground if not used. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 11 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 1: Media Dependent Interface (Continued) 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scrip tio n N6 N7 I/O, D Media Dependent Interface[2]. A21 A22 56 57 MDI[2]+ MDI[2]- In 1000BASE-T mode in MDI configuration, MDI[2] correspond to BI_DC. In MDIX configuration, MDI[2] corresponds to BI_DD. In 100BASE-TX and 10BASE-T modes, MDI[2] are not used. MDI[2] should be tied to ground if not used. N8 N9 B20 A23 61 62 MDI[3]+ MDI[3]- I/O, D Media Dependent Interface[3]. In 1000BASE-T mode in MDI configuration, MDI[3] correspond to BI_DD. In MDIX configuration, MDI[3] correspond to BI_DC. In 100BASE-TX and 10BASE-T modes, MDI[3] are not used. MDI[3] should be tied to ground if not used. Doc. No. MV-S105540-00, Rev. A Page 12 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description The GMII interface supports both 1000BASE-T and 1000BASE-X modes of operation. The GMII interface pins are also used for the TBI interface. See Table 3 for TBI pin definitions. The MAC interface pins are 3.3V tolerant. Table 2: GMII/MII Interfaces 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pin Type De scr ip tio n E2 B4 14 GTX_CLK I GMII Transmit Clock. GTX_CLK provides a 125 MHz clock reference for TX_EN, TX_ER, and TXD[7:0]. This clock can be stopped when the device is in 10/100BASET modes, and also during Auto-Negotiation. D1 B2 10 TX_CLK O, Z MII Transmit Clock. TX_CLK provides a 25 MHz clock reference for TX_EN, TX_ER, and TXD[3:0] in 100BASE-TX mode, and a 2.5 MHz clock reference in 10BASE-T mode. TX_CLK provides a 25 MHz, 2.5 MHz, or 0 MHz clock during 1000 Mbps Good Link, Auto-Negotiation, and Link Lost states depending on the setting of register 20.6:4. The 2.5 MHz clock is the default rate, which may be programmed to another frequency by writing to register 20.6:4. E1 A5 16 TX_EN I GMII and MII Transmit Enable. In GMII/MII mode when TX_EN is asserted, data on TXD[7:0] along with TX_ER is encoded and transmitted onto the cable. TX_EN is synchronous to GTX_CLK, and synchronous to TX_CLK in 100BASE-TX and 10BASE-T modes. F2 A4 13 TX_ER I GMII and MII Transmit Error. In GMII/MII mode when TX_ER and TX_EN are both asserted, the transmit error symbol is transmitted onto the cable. When TX_ER is asserted with TX_EN de-asserted, carrier extension symbol is transmitted onto the cable. TX_ER is synchronous to GTX_CLK, and synchronous to TX_CLK in 100BASE-TX and 10BASE-T modes. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 13 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 2: GMII/MII Interfaces (Continued) 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # J2 J1 H3 H1 H2 G3 G2 F1 B10 A10 B9 A9 B8 B7 B6 A6 29 28 26 25 24 20 19 18 TXD[7] TXD[6] TXD[5] TXD[4] TXD[3]/TXD[3] TXD[2]/TXD[2] TXD[1]/TXD[1] TXD[0]/TXD[0] Pin Ty pe Des cription I GMII and MII Transmit Data. In GMII mode, TXD[7:0] present the data byte to be transmitted onto the cable in 1000BASE-T mode. In MII mode, TXD[3:0] present the data nibble to be transmitted onto the cable in 100BASE-TX and 10BASE-T modes. TXD[7:4] are ignored in these modes, but should be driven either high or low. These pins must not float. TXD[7:0] are synchronous to GTX_CLK, and synchronous to TX_CLK in 100BASE-TX and 10BASE-T modes. Inputs TXD[7:4] should be tied low if not used (e.g., RGMII mode). C1 B1 7 RX_CLK O, Z GMII and MII Receive Clock. RX_CLK provides a 125 MHz clock reference for RX_DV, RX_ER, and RXD[7:0] in 1000BASE-T mode, a 25 MHz clock reference in 100BASE-TX mode, and a 2.5 MHz clock reference in 10BASE-T mode. TX_TCLK comes from the RX_CLK pins used in jitter testing. Refer to Register 9 for jitter test modes. B1 B44 4 RX_DV O, Z GMII and MII Receive Data Valid. When RX_DV is asserted, data received on the cable is decoded and presented on RXD[7:0] and RX_ER. RX_DV is synchronous to RX_CLK. D2 A2 8 RX_ER O, Z GMII and MII Receive Error. When RX_ER and RX_DV are both asserted, the signals indicate an error symbol is detected on the cable. When RX_ER is asserted with RX_DV deasserted, a false carrier or carrier extension symbol is detected on the cable. RX_ER is synchronous to RX_CLK. Doc. No. MV-S105540-00, Rev. A Page 14 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 2: GMII/MII Interfaces (Continued) 117 -T FB GA 96-aQFN 12 8-PQF P Pin Name Pin # Pi n # Pin # C5 A2 A1 C4 B3 C3 D3 B2 B40 A47 A48 B42 A49 A50 B43 A51 120 121 123 124 125 126 128 3 RXD[7] RXD[6] RXD[5] RXD[4] RXD[3]/RXD[3] RXD[2]/RXD[2] RXD[1]/RXD[1] RXD[0]/RXD[0] Pin Ty pe Des cription O, Z GMII and MII Receive Data. Symbols received on the cable are decoded and presented on RXD[7:0] in 1000BASE-T mode. In MII mode, RXD[3:0] are used in 100BASE-TX and 10BASE-T modes. In MII mode, RXD[7:4] are driven low. RXD[7:0] is synchronous to RX_CLK. B5 B39 115 CRS O, Z GMII and MII Carrier Sense. CRS asserts when the receive medium is non-idle. In halfduplex mode, CRS is also asserted during transmission. CRS assertion during halfduplex transmit can be disabled by programming register 16.11 to 0. CRS is asynchronous to RX_CLK, GTX_CLK, and TX_CLK. B6 A45 114 COL O, Z GMII and MII Collision. In 10/100/ 1000BASE-T full-duplex modes, COL is always low. In 10/100/1000BASE-T halfduplex modes, COL asserts only when both the transmit and receive media are non-idle. In 10BASE-T half-duplex mode, COL is asserted to indicate signal quality error (SQE). SQE can be disabled by clearing register 16.2 to zero. COL is asynchronous to RX_CLK, GTX_CLK, and TX_CLK. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 15 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver The TBI interface supports 1000BASE-T mode of operation. The TBI interface uses the same pins as the GMII interface. The MAC interface pins are 3.3V tolerant. Table 3: TBI Interface 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n E2 I TBI Transmit Clock. In TBI mode, GTX_CLK is used as TBI_TXCLK. TBI_TXCLK is a 125 MHz transmit clock. B4 14 GTX_CLK/ TBI_TXCLK TBI_TXCLK provides a 125 MHz clock reference for TX_EN, TX_ER, and TXD[7:0]. D1 B2 10 TX_CLK/RCLK1 O, Z J2 J1 H3 H1 H2 G3 G2 F1 B10 A10 B9 A9 B8 B7 B6 A6 29 28 26 25 24 20 19 18 TXD[7] TXD[6] TXD[5] TXD[4] TXD[3] TXD[2] TXD[1] TXD[0] I E1 A5 16 TX_EN/ TXD8 I TBI 62.5 MHz Receive Clock- even code group. In TBI mode, TX_CLK is used as RCLK1. TBI Transmit Data. TXD[7:0] presents the data byte to be transmitted onto the cable. TXD[9:0] are synchronous to GTX_CLK. Inputs TXD[7:4] should be tied low if not used (e.g., RTBI mode). TBI Transmit Data. In TBI mode, TX_EN is used as TXD8. TXD[9:0] are synchronous to GTX_CLK. F2 A4 13 TX_ER/ TXD9 I TBI Transmit Data. In TBI mode, TX_ER is used as TXD9. TXD[9:0] are synchronous to GTX_CLK. TX_ER should be tied low if not used (e.g., RTBI mode). C1 B1 7 RX_CLK/ RCLK0 O, Z TBI 62.5 MHz Receive Clock- odd code group. In the TBI mode, RX_CLK is used as RCLK0. C5 A2 A1 C4 B3 C3 D3 B2 B40 A47 A48 B42 A49 A50 B43 A51 120 121 123 124 125 126 128 3 RXD[7] RXD[6] RXD[5] RXD[4] RXD[3] RXD[2] RXD[1] RXD[0] O, Z TBI Receive Data code group [7:0]. In the TBI mode, RXD[7:0] present the data byte to be transmitted to the MAC. Symbols received on the cable are decoded and presented on RXD[7:0]. B1 B44 4 RX_DV/ RXD8 O, Z RXD[7:0] are synchronous to RCLK0 and RCLK1. TBI Receive Data code group bit 8. In the TBI mode, RX_DV is used as RXD8. RXD[9:0] are synchronous to RCLK0 and RCLK1. Doc. No. MV-S105540-00, Rev. A Page 16 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 3: TBI Interface (Continued) 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion D2 O, Z TBI Receive Data code group bit 9. In the TBI mode, RX_ER is used as RXD9. A2 8 RX_ER/ RXD9 RXD[9:0] are synchronous to RCLK0 and RCLK1. B5 B39 115 CRS/ COMMA O, Z TBI Valid Comma Detect. In the TBI mode, CRS is used as COMMA. B6 A45 114 COL/LPBK I TBI Mode Loopback. In the TBI mode, COL is used to indicate loopback on the TBI. When a "0 - 1" transition is sampled on this pin, bit 0.14 is set to 1. When a "1 - 0" is sampled on this pin, bit 0.14 is reset to 0. If this feature is not used, the COL pin should be driven low on the board. This pin should not be left floating in TBI mode. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 17 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver The RGMII interface supports 10/100/1000BASE-T and 1000BASE-X modes of operation.The RGMII interface pins are also used for the RTBI interface. See Table 5 for RTBI pin definitions. The MAC interface pins are 3.3V tolerant. Table 4: RGMII Interface 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n E2 B4 14 GTX_CLK/ TXC I RGMII Transmit Clock provides a 125 MHz, 25 MHz, or 2.5 MHz reference clock with 50 ppm tolerance depending on speed. In RGMII mode, GTX_CLK is used as TXC. H2 G3 G2 F1 B8 B7 B6 A6 24 20 19 18 TXD[3]/TD[3] TXD[2]/TD[2] TXD[1]/TD[1] TXD[0]/TD[0] I RGMII Transmit Data. In RGMII mode, TXD[3:0] are used as TD[3:0]. In RGMII mode, TXD[3:0] run at double data rate with bits [3:0] presented on the rising edge of GTX_CLK, and bits [7:4] presented on the falling edge of GTX_CLK. In this mode, TXD[7:4] are ignored. In RGMII 10/100BASE-T modes, the transmit data nibble is presented on TXD[3:0] on the rising edge of GTX_CLK. E1 A5 16 TX_EN/ TX_CTL I RGMII Transmit Control. In RGMII mode, TX_EN is used as TX_CTL. TX_EN is presented on the rising edge of GTX_CLK. A logical derivative of TX_EN and TX_ER is presented on the falling edge of GTX_CLK. C1 B1 7 RX_CLK/ RXC O, Z RGMII Receive Clock provides a 125 MHz, 25 MHz, or 2.5 MHz reference clock with 50 ppm tolerance derived from the received data stream depending on speed. In RGMII mode, RX_CLK is used as RXC. Doc. No. MV-S105540-00, Rev. A Page 18 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 4: RGMII Interface (Continued) 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion B1 O, Z RGMII Receive Control. In RGMII mode, RX_DV is used as RX_CTL. RX_DV is presented on the rising edge of RX_CLK. B44 4 RX_DV/ RX_CTL A logical derivative of RX_DV and RX_ER is presented on the falling edge of RX_CLK. B3 C3 D3 B2 A49 A50 B43 A51 125 126 128 3 RXD[3]/RD[3] RXD[2]/RD[2] RXD[1]/RD[1] RXD[0]/RD[0] O, Z RGMII Receive Data. In RGMII mode, RXD[3:0] are used as RD[3:0]. In RGMII mode, RXD[3:0] run at double data rate with bits [3:0] presented on the rising edge of RX_CLK, and bits [7:4] presented on the falling edge of RX_CLK. In this mode, RXD[7:4] are ignored. In RGMII 10/100BASE-T modes, the receive data nibble is presented on RXD[3:0] on the rising edge of RX_CLK. RXD[3:0] are synchronous to RX_CLK. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 19 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver The RTBI interface supports 1000BASE-T mode of operation. The RTBI interface uses the same pins as the RGMII interface. The MAC interface pins are 3.3V tolerant. Table 5: RTBI Interface 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n E2 B4 14 GTX_CLK/ TXC I RGMII Transmit Clock provides a 125 MHz reference clock with 50 ppm tolerance. In RTBI mode, GTX_CLK is used as TXC. H2 G3 G2 F1 B8 B7 B6 A6 24 20 19 18 TXD[3]/TD[3] TXD[2]/TD[2] TXD[1]/TD[1] TXD[0]/TD[0] I RTBI Transmit Data. In RTBI mode, TXD[3:0] are used as TD[3:0]. TD[3:0] run at double data rate with bits [3:0] presented on the rising edge of GTX_CLK, and bits [8:5] presented on the falling edge of GTX_CLK. In this mode, TXD[7:4] are ignored. E1 A5 16 TX_EN/ TD4_TD9 I RTBI Transmit Data. In RTBI mode, TX_EN is used as TD4_TD9. TD4_TD9 runs at a double data rate with bit 4 presented on the rising edge of GTX_CLK, and bit 9 presented on the falling edge of GTX_CLK. C1 B1 7 RX_CLK/ RXC O, Z RTBI Receive Clock provides a 125 MHz reference clock with 50 ppm tolerance derived from the received data stream. In RTBI mode, RX_CLK is used as RXC. B3 C3 D3 B2 91 A50 B43 A51 125 126 128 3 RXD[3]/RD[3] RXD[2]/RD[2] RXD[1]/RD[1] RXD[0]/RD[0] O, Z RTBI Receive Data. In RTBI mode, RXD[3:0] are used as RD[3:0]. RD[3:0] runs at double data rate with bits [3:0] presented on the rising edge of RX_CLK, and bits [8:5] presented on the falling edge of RX_CLK. In this mode, RXD[7:4] are ignored. B1 B44 4 RX_DV/ RD4_RD9 O, Z RTBI Receive Data. In RTBI mode, RX_DV is used as RD4_RD9. RD4_RD9 runs at a double data rate with bit 4 presented on the rising edge of RX_CLK, and bit 9 presented on the falling edge of RX_CLK. Doc. No. MV-S105540-00, Rev. A Page 20 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 6: SGMII Interface 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion A3 A4 I SGMII Transmit Data. 1.25 GBaud input Positive and Negative. B38 A44 113 112 S_IN+ S_IN- Input impedance on the S_IN pins may be programmed for 50 ohm or 75 ohm impedance by setting register 26.6. The input impedance default setting is determined by the 75/50 OHM configuration pin. A5 A6 A43 B37 110 109 S_CLK+ S_CLK- I/O SGMII 625 MHz Receive Clock. For Serial Interface modes (HWCFG_MODE[3:0] = 1x00) the S_CLK pins become Signal Detect (SD) inputs. A7 A8 A42 A41 107 105 S_OUT+ S_OUT- O, Z SGMII Receive Data. 1.25 GBaud output Positive and Negative. Output impedance on the S_OUT pins may be programmed for 50 ohm or 75 ohm impedance by setting register 26.5. Output amplitude can be adjusted via register 26.2:0. The output impedance default setting is determined by the 75/50 OHM configuration pin. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 21 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 7: 1.25 GHz Serial High Speed Interface 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n A3 A4 I 1.25 GHz input - Positive and Negative. When this interface is used as a MAC interface, the MAC transmitter's positive output connects to the S_IN+. The MAC transmitter's negative output connects to the S_IN-. B38 A44 113 112 S_IN+ S_IN- When this interface is used as a fiber interface, the fiber-optic transceiver's positive output connects to the S_IN+. The fiber-optic transceiver's negative output connects to the S_IN-. Input impedance on the S_IN pins may be programmed for 50 ohm or 75 ohm impedance by setting register 26.6. The input impedance default setting is determined by the 75/50 OHM configuration pin. A5 A6 A43 B37 110 109 S_CLK+/SD+ S_CLK-/SD- I Signal Detect input. For Serial Interface modes the S_CLK pins become Signal Detect (SD) inputs. A7 A8 A42 A41 107 105 S_OUT+ S_OUT- O, Z 1.25 GHz output - Positive and Negative. When this interface is used as a MAC interface, S_OUT+ connects to the MAC receiver's positive input. S_OUT- connects to the MAC receiver's negative input. When this interface is used as a fiber interface, S_OUT+ connects to the fiber-optic transceiver's positive input. S_OUT- connects to the fiber-optic transceiver's negative input. Output impedance on the S_OUT pins may be programmed for 50 ohm or 75 ohm impedance by setting register 26.5. Output amplitude can be adjusted via register 26.2:0. The output impedance default setting is determined by the 75/50 OHM configuration pin. Doc. No. MV-S105540-00, Rev. A Page 22 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 7: 1.25 GHz Serial High Speed Interface (Continued) 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion B3 A49 125 RXD[3] O, Z Serial MAC interface Copper Link Status[1] connection. 1 = Copper link up 0 = Copper link down C3 A50 126 RXD[2] O, Z Serial MAC interface Copper Link Status[0] connection. 1 = Copper link down 0 = Copper link up D3 B43 128 RXD[1] O, Z Serial MAC interface PHY_SIGDET[1] connection. 1 = S_OUT valid code groups according to clause 36. 0 = S_OUT invalid B2 A51 3 RXD[0] O, Z Serial MAC interface PHY_SIGDET[0] connection. 1 = S_OUT invalid 0 = S_OUT valid code groups according to clause 36 Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 23 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 8: Management Interface and Interrupt 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n L3 A14 35 MDC I 3.3V Tolerant MDC is the management data clock reference for the serial management interface. A continuous clock stream is not expected. The maximum frequency supported is 8.3 MHz. M1 A13 33 MDIO I/O 3.3V Tolerant MDIO is the management data. MDIO transfers management data in and out of the device synchronously to MDC. This pin requires a pull-up resistor in a range from 1.5 kohm to 10 kohm. L1 A12 32 INTn D The polarity of the INTn pin may be programmed at hardware reset by setting the INT_POL bit. Polarity: 0 = Active High 1 = Active Low Table 9: Two-Wire Serial Interface 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n L3 A14 35 MDC/SCL I Two-Wire Serial Interface (TWSI) serial clock line. When the 88E1111 device is connected to the bus, MDC connects to the serial clock line (SCL). Data is input on the rising edge of SCL, and output on the falling edge. M1 A13 33 MDIO/SDA I/O TWSI serial data line. When the 88E1111 device is connected to the bus, MDIO connects to the serial data line (SDA). This pin is open-drain and may be wire-ORed with any number of open-drain devices. Doc. No. MV-S105540-00, Rev. A Page 24 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 10: LED Interface 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion C8 O, mA Parallel LED output for 10BASE-T link or speed. This active low LED pin may be programmed in direct drive or combined LED modes by programming register LED_LINK Control register 24.4:3. B35 100 LED_LINK10 In direct drive LED mode, this pin indicates 10 Mbps link up or down. In combined LED mode, the output from LED_LINK10, LED_LINK100, and LED_LINK1000 must be read together to determine link and speed status. LED_LINK10 is a multi-function pin used to configure the 88E1111 device at the deassertion of hardware reset. B8 A40 99 LED_LINK100 O, mA Parallel LED output for 100BASE-TX link or speed. This active low LED pin may be programmed in direct drive or combined LED modes by programming register LED_LINK Control register 24.4:3. In direct drive LED mode, this pin indicates 100 Mbps link up or down. In combined LED mode, the output from LED_LINK10, LED_LINK100, and LED_LINK1000 must be read together to determine link and speed status. LED_LINK100 is a multi-function pin used to configure the 88E1111 device at the deassertion of hardware reset. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 25 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 10: LED Interface (Continued) 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n A9 O, mA Parallel LED output for 1000BASE-T link/ speed or link indicator. This active low LED pin may be programmed in direct drive or combined LED modes by programming register LED_LINK Control register 24.4:3. A39 98 LED_LINK1000 In direct drive LED mode, this pin indicates 1000 Mbps link up or down. In combined LED mode, the output from LED_LINK1000 indicates link status. LED_LINK1000 is a multi-function pin used to configure the 88E1111 device at the deassertion of hardware reset. E8 B33 95 LED_DUPLEX O, mA Parallel LED duplex or duplex/collision modes. The LED_DUPLEX pin may be programmed to Mode 1 or Mode 2 by setting register bit 24.2. Mode 1 Low = Full-duplex High = Half-duplex Blink = Collision Mode 2 Low = Full-duplex High = Half-duplex Mode 3 Low = Fiber Link up High = Fiber Link down LED_DUPLEX is a multi-function pin used to configure the 88E1111 device at the deassertion of hardware reset. Doc. No. MV-S105540-00, Rev. A Page 26 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 10: LED Interface (Continued) 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion C9 O, mA Parallel LED Receive Activity or Receive Activity/Link modes. LED_RX may be programmed to Mode 1 or Mode 2 by setting register bit 24.1. A37 92 LED_RX Mode 1 Low = Receiving High = Not receiving Mode 2 Low = Link up High = Link down Blink = Receiving LED_RX is a multi-function pin used to configure the 88E1111 device at the de-assertion of hardware reset. D9 B32 91 LED_TX O, mA Parallel LED Transmit Activity or RX/TX Activity/Link modes. LED_TX may be programmed to Mode 1 or Mode 2 by setting register bit 24.0. Mode 1 Low = Transmitting High = Not transmitting Mode 2 Low = Link up High = Link down Blink = Transmitting or receiving LED_TX is a multi-function pin used to configure the 88E1111 device at the de-assertion of hardware reset. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 27 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 11: JTAG Interface 117-T FBGA 9 6- aQ FN 128 -PQF P Pi n Typ e Pin # Pin # Pin # Pin Nam e Des cription L7 B21 67 TDI I, PU Boundary scan test data input. TDI contains an internal 150 kohm pull-up resistor. L8 B22 69 TMS I, PU Boundary scan test mode select input. TMS contains an internal 150 kohm pull-up resistor. L9 A26 70 TCK I, PU Boundary scan test clock input. TCK contains an internal 150 kohm pull-up resistor. M9 A25 68 TRSTn I, PU Boundary scan test reset input. Active low. TRSTn contains an internal 150 kohm pullup resistor as per the 1149.1 specification. After power up, the JTAG state machine should be reset by applying a low signal on this pin, or by keeping TMS high and applying 5 TCK pulses, or by pulling this pin low by a 4.7 kohm resistor. K8 A27 72 TDO O, Z Boundary scan test data output. Doc. No. MV-S105540-00, Rev. A Page 28 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 12: Clock/Configuration/Reset/I/O 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion K2 B11 31 125CLK O Clock 125. A generic 125 MHz clock reference generated for use on the MAC device. This output can be disabled via DIS_125 through the CONFIG[3] pin. D8 A35 88 CONFIG[0] I CONFIG[0] pin configures PHY_ADR[2:0] bits of the physical address. Each LED pin is hardwired to a constant value. The values associated to the CONFIG[0] pin are latched at the de-assertion of hardware reset. CONFIG[0] pin must be tied to one of the pins based on the configuration options selected. They should not be left floating. For the Two-Wire Serial Interface (TWSI) device address, the lower 5 bits, which are PHYADR[4:0], are latched during hardware reset, and the device address bits [6:5] are fixed at `10'. E9 B30 87 CONFIG[1] I CONFIG[1] pin configures PHY_ADR[4:3] and ENA_PAUSE options. Each LED pin is hardwired to a constant value. The values associated to the CONFIG[1] pin are latched at the de-assertion of hardware reset. CONFIG[1] pin must be tied to one of the pins based on the configuration options selected. They should not be left floating. For the TWSI device address, the lower 5 bits, which are PHYADR[4:0], are latched during hardware reset, and the device address bits [6:5] are fixed at `10'. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 29 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 12: Clock/Configuration/Reset/I/O (Continued) 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n F8 I CONFIG[2] pin configures ANEG[3:1] bits. A34 86 CONFIG[2] Each LED pin is hardwired to a constant value. The values associated to the CONFIG[2] pin are latched at the de-assertion of hardware reset. CONFIG[2] pin must be tied to one of the pins based on the configuration options selected. They should not be left floating. G7 A33 82 CONFIG[3] I CONFIG[3] pin configures ANEG[0], ENA_XC, and DIS_125 options. Each LED pin is hardwired to a constant value. The values associated to the CONFIG[3] pin are latched at the de-assertion of hardware reset. CONFIG[3] pin must be tied to one of the pins based on the configuration options selected. They should not be left floating. F9 B28 81 CONFIG[4] I CONFIG[4] pin configures HWCFG_MODE[2:0] options. G9 A32 80 CONFIG[5] I CONFIG[5] pin configures DIS_FC, DIS_SLEEP, and HWCFG_MODE[3] options. G8 B27 79 CONFIG[6] I CONFIG[6] pin configures SEL_TWSI, INT_POL, and 75/50 OHM options. H8 B26 77 SEL_FREQ H9 A30 76 XTAL1 I Reference Clock. 25 MHz 50 ppm or 125 MHz 50 ppm oscillator input. PLL clocks are not recommended. J9 B25 75 XTAL2 0 Reference Clock. 25 MHz 50 ppm tolerance crystal reference. When the XTAL2 pin is not connected, it should be left floating. There is no option for a 125 MHz crystal. See "Crystal Oscillator" Application Note for details. Frequency Selection for XTAL1 input NC = Selects 25 MHz clock input. Tied low = Selects 125 MHz clock input. Internally divided to 25 MHz. SEL_FREQ is internally pulled up. Doc. No. MV-S105540-00, Rev. A Page 30 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 12: Clock/Configuration/Reset/I/O (Continued) 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion K3 B13 36 RESETn I Hardware reset. Active low. XTAL1 must be active for a minimum of 10 clock cycles before the rising edge of RESETn. RESETn must be pulled high for normal operation. L4 A15 37 COMA I COMA disables all active circuitry to draw absolute minimum power. The COMA power mode can be activated by asserting high on the COMA pin. To deactivate the COMA power mode, tie the COMA pin low. Upon deactivating COMA mode, the 88E1111 device will continue normal operation. The COMA power mode cannot be enabled as long as hardware reset is enabled. In COMA mode, the PHY cannot wake up on its own by detecting activity on the CAT 5 cable. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 31 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 13: Test 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n M5 M6 Analog PD Test pins. These pins should be left floating but brought out for probing. 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n M2 Analog I Constant voltage reference. External 5.0 kohm 1% resistor connection to VSS required for each pin. Table 14: A20 B18 53 54 HSDAC+ HSDAC- Control and Reference B14 39 RSET Doc. No. MV-S105540-00, Rev. A Page 32 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description Pin Description Table 15: Power & Ground 117 - TF BGA 96-a QF N 1 28-PQFP Pin Name Pin # Pin # Pin # Pi n Typ e Desc rip t ion B7 M3 M4 M7 M8 N5 B15 A19 B17 B19 A24 B36 44 49 52 59 64 104 AVDD Power Analog Power. 2.5V. C6 C7 D7 E3 E7 F3 J3 J7 A1 B3 B5 A8 A31 B29 A36 A38 A46 2 6 12 17 23 27 78 85 90 96 117 118 DVDD Power Digital Power. 1.0V (Instead of 1.0V, 1.2V can be used). B9 F7 J8 B24 B31 B34 73 89 97 VDDOH Power 2.5V Power Supply for LED and CONFIG pins. K9 L2 B12 B23 34 71 VDDOX Power 2.5V Supply for the MDC/MDIO, INTn, 125CLK, RESETn, JTAG pin Power. B4 C2 K1 A3 A11 B41 A52 5 11 30 122 VDDO Power 2.5V I/O supply for the MAC interface pins. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 33 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 15: Power & Ground (Continued) 117 -T F B GA 96-aQFN 1 28-PQF P Pin Name Pin # Pin # Pin # Pin Typ e De scr ip tio n D4 D5 D6 E4 E5 E6 F4 F5 F6 G4 G5 G6 H4 H5 H6 J4 J5 J6 K4 K5 K6 L5 L6 EPAD 1 9 15 21 22 38 40 43 45 48 51 55 58 60 63 65 66 83 84 93 94 101 102 103 106 108 111 116 119 127 VSS GND Global ground H7 A29 74 VSSC GND Ground reference for XTAL1 and XTAL2 pins. This pin must be connected to the ground. G1 K7 A7 A28 50 NC NC No connect. Do not connect these pins to anything Doc. No. MV-S105540-00, Rev. A Page 34 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description I/O State at Various Test or Reset Modes 1.5 I/O State at Various Test or Reset Modes P in ( s ) I so l a t e L o o pb a c k or Normal o p e r a ti o n S o ftw a r e Reset Hardware Reset Power Down Coma Power D ow n a n d I s o la t e MDI[3:0] Active Active Tri-state Tri-state Tri-state Tri-state Tri-state TX_CLK Tri-state Active Reg. 16.3 state 0 = Low 1 = Active Low Reg. 16.3 state 0 = Low 1 = Active Reg. 16.3 state 0 = Low 0 = Static but can be either high or low Tri-state RXD[0], RXD[2] Tri-state Active High High High High Tri-state RXD[7:3,1], RX_DV, RX_ER, CRS Tri-state Active Low Low Low Low Tri-state COL Tri-state TBI mode input else -active Tri-state Tri-state TBI mode input else - low TBI mode input else - low Tri-state RX_CLK Tri-state Active Reg. 16.3 state 0 = Low 1 = Active Low Reg. 16.3 state 0 = Low 1 = Active Reg. 16.3 state 0 = Low 0 = Static but can be either high or low Tri-state S_CLK S_OUT Active Active Tri-state Tri-state Reg. 16.3 state 0 = Tri-state 1 = Active Tri-state Active MDIO Active Active Active Tri-state Active Tri-state Active INT Active Active Tri-state Tri-state Tri-state Tri-state Tri-state LED_*** Active Active High High High High High TDO Tri-state Tri-state Tri-state Tri-state Tri-state Active Tri-state 125CLK Reg. 16.4 state 0 = Toggle 1 = Low Reg. 16.4 state 0 = Toggle 1 = Low Reg. 16.4 state 0 = Toggle 1 = Low Toggle Reg. 16.4 state 0 = Toggle 1 = Low Reg. 16.3 state 0 = Static but can be either high or low 0 = Low Reg. 16.4 state 0 = Toggle 1 = Low Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 35 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver 1.6 117-Pin TFBGA Pin Assignment List - Alphabetical by Signal Name Pin # Pin Name Pin # Pin Name K2 125CLK A9 LED_LINK1000 B7 AVDD C9 LED_RX M3 AVDD D9 LED_TX M4 AVDD L3 MDC M7 AVDD N2 MDI[0]- M8 AVDD N1 MDI[0]+ N5 AVDD N4 MDI[1]- B6 COL N3 MDI[1]+ L4 COMA N7 MDI[2]- D8 CONFIG[0] N6 MDI[2]+ E9 CONFIG[1] N9 MDI[3]- F8 CONFIG[2] N8 MDI[3]+ G7 CONFIG[3] M1 MDIO F9 CONFIG[4] G1 NC G9 CONFIG[5] K7 NC G8 CONFIG[6] K3 RESETn B5 CRS M2 RSET C6 DVDD B2 RXD0 C7 DVDD D3 RXD1 D7 DVDD C3 RXD2 E3 DVDD B3 RXD3 E7 DVDD C4 RXD4 F3 DVDD A1 RXD5 J3 DVDD A2 RXD6 J7 DVDD C5 RXD7 E2 GTX_CLK C1 RX_CLK M6 HSDAC- B1 RX_DV M5 HSDAC+ D2 RX_ER L1 INTn A6 S_CLK- E8 LED_DUPLEX A5 S_CLK+ C8 LED_LINK10 A4 S_IN- B8 LED_LINK100 A3 S_IN+ Doc. No. MV-S105540-00, Rev. A Page 36 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description 117-Pin TFBGA Pin Assignment List - Alphabetical by Signal Name 1.6 117-Pin TFBGA Pin Assignment List - Alphabetical by Signal Name (Continued) Pin # Pin Name Pin # Pin Name A8 S_OUT- D4 VSS A7 S_OUT+ D5 VSS H8 SEL_FREQ D6 VSS L9 TCK E4 VSS L7 TDI E5 VSS K8 TDO E6 VSS L8 TMS F4 VSS M9 TRSTn F5 VSS F1 TXD0 F6 VSS G2 TXD1 G4 VSS G3 TXD2 G5 VSS H2 TXD3 G6 VSS H1 TXD4 H4 VSS H3 TXD5 H5 VSS J1 TXD6 H6 VSS J2 TXD7 J4 VSS D1 TX_CLK J5 VSS E1 TX_EN J6 VSS F2 TX_ER K4 VSS B4 VDDO K5 VSS C2 VDDO K6 VSS K1 VDDO L5 VSS B9 VDDOH L6 VSS F7 VDDOH H7 VSSC J8 VDDOH H9 XTAL1 K9 VDDOX J9 XTAL2 L2 VDDOX Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 37 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver 1.7 96-Pin aQFN Pin Assignment List - Alphabetical by Signal Name NOTE: The 96-pin BCC package is obsolete and is no longer available. The 96-Pin aQFN package is a pin compatible replacement for the 96-Pin BCC package. 96- Pin BCC Pin # 96- Pin aQ FN Pi n # Pi n N a m e 96- P in BCC Pin # 96- Pin aQ FN Pi n # Pin Name 22 B11 125CLK 74 A40 LED_LINK100 32 B15 AVDD 73 A39 LED_LINK1000 35 A19 AVDD 69 A37 LED_RX 36 B17 AVDD 68 B32 LED_TX 40 B19 AVDD 25 A14 MDC 45 A24 AVDD 31 A17 MDI[0]- 78 B36 AVDD 29 A16 MDI[0]+ 83 A45 COL 34 B16 MDI[1]- 27 A15 COMA 33 A18 MDI[1]+ 65 A35 CONFIG[0] 41 A22 MDI[2]- 64 B30 CONFIG[1] 39 A21 MDI[2]+ 63 A34 CONFIG[2] 43 A23 MDI[3]- 61 A33 CONFIG[3] 42 B20 MDI[3]+ 60 B28 CONFIG[4] 24 A13 MDIO 59 A32 CONFIG[5] 13 A7 NC 58 B27 CONFIG[6] 51 A28 NC 84 B39 CRS 28 B13 RESETn 1 A1 DVDD 30 B14 RSET 6 B3 DVDD 95 A51 RXD0 10 B5 DVDD 92 B43 RXD1 15 A8 DVDD 93 A50 RXD2 57 A31 DVDD 91 A49 RXD3 62 B29 DVDD 90 B42 RXD4 67 A36 DVDD 89 A48 RXD5 71 A38 DVDD 87 A47 RXD6 85 A46 DVDD 86 B40 RXD7 8 B4 GTX_CLK 2 B1 RX_CLK 38 B18 HSDAC- 94 B44 RX_DV 37 A20 HSDAC+ 3 A2 RX_ER 23 A12 INTn 80 B37 S_CLK- 70 B33 LED_DUPLEX 79 A43 S_CLK+ 76 B35 LED_LINK10 81 A44 S_IN- Doc. No. MV-S105540-00, Rev. A Page 38 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description 96-Pin aQFN Pin Assignment List - Alphabetical by Signal Name 1.7 96-Pin aQFN Pin Assignment List - Alphabetical by Signal Name (Continued) NOTE: The 96-pin BCC package is obsolete and is no longer available. The 96-Pin aQFN package is a pin compatible replacement for the 96-Pin BCC package. 96- Pin BCC Pin # 96 - Pin aQ FN Pi n # Pin Name 96- Pin BCC Pin # 96 - Pin aQ FN Pi n # Pin Name 82 B38 S_IN+ 4 B2 TX_CLK 75 A41 S_OUT- 9 A5 TX_EN 77 A42 S_OUT+ 7 A4 TX_ER 56 B26 SEL_FREQ 5 A3 VDDO 49 A26 TCK 21 A11 VDDO 44 B21 TDI 88 B41 VDDO 50 A27 TDO 96 A52 VDDO 46 B22 TMS 52 B24 VDDOH 47 A25 TRSTn 66 B31 VDDOH 11 A6 TXD0 72 B34 VDDOH 12 B6 TXD1 26 B12 VDDOX 14 B7 TXD2 48 B23 VDDOX 16 B8 TXD3 EPAD EPAD VSS 17 A9 TXD4 53 A29 VSSC 18 B9 TXD5 55 A30 XTAL1 19 A10 TXD6 54 B25 XTAL2 20 B10 TXD7 Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 39 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver 1.8 128-Pin PQFP Pin Assignment List - Alphabetical by Signal Name Pin # Pin Name Pin # Pin Name 31 125CLK 32 INTn 44 AVDD 95 LED_DUPLEX 49 AVDD 100 LED_LINK10 52 AVDD 99 LED_LINK100 59 AVDD 98 LED_LINK1000 64 AVDD 92 LED_RX 104 AVDD 91 LED_TX 114 COL 35 MDC 37 COMA 41 MDI[0]+ 88 CONFIG[0] 42 MDI[0]- 87 CONFIG[1] 46 MDI[1]+ 86 CONFIG[2] 47 MDI[1]- 82 CONFIG[3] 56 MDI[2]+ 81 CONFIG[4] 57 MDI[2]- 80 CONFIG[5] 61 MDI[3]+ 79 CONFIG[6] 62 MDI[3]- 115 CRS 33 MDIO 2 DVDD 50 NC 6 DVDD 36 RESETn 12 DVDD 39 RSET 17 DVDD 7 RX_CLK 23 DVDD 4 RX_DV 27 DVDD 8 RX_ER 78 DVDD 3 RXD0 85 DVDD 128 RXD1 90 DVDD 126 RXD2 96 DVDD 125 RXD3 117 DVDD 124 RXD4 118 DVDD 123 RXD5 14 GTX_CLK 121 RXD6 53 HSDAC+ 120 RXD7 54 HSDAC- 110 S_CLK+ Doc. No. MV-S105540-00, Rev. A Page 40 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Signal Description 128-Pin PQFP Pin Assignment List - Alphabetical by Signal Name 1.8 128-Pin PQFP Pin Assignment List - Alphabetical by Signal Name (Continued) Pin # Pin Name Pin # Pin Name 109 S_CLK- 9 VSS 113 S_IN+ 15 VSS 112 S_IN- 21 VSS 107 S_OUT+ 22 VSS 105 S_OUT- 38 VSS 77 SEL_FREQ 40 VSS 70 TCK 43 VSS 67 TDI 45 VSS 72 TDO 48 VSS 69 TMS 51 VSS 68 TRSTn 55 VSS 10 TX_CLK 58 VSS 16 TX_EN 60 VSS 13 TX_ER 63 VSS 18 TXD0 65 VSS 19 TXD1 66 VSS 20 TXD2 83 VSS 24 TXD3 84 VSS 25 TXD4 93 VSS 26 TXD5 94 VSS 28 TXD6 101 VSS 29 TXD7 102 VSS 5 VDDO 103 VSS 11 VDDO 106 VSS 30 VDDO 108 VSS 122 VDDO 111 VSS 73 VDDOH 116 VSS 89 VDDOH 119 VSS 97 VDDOH 127 VSS 34 VDDOX 74 VSSC 71 VDDOX 76 XTAL1 1 VSS 75 XTAL2 Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 41 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Section 2. Package Mechanical Dimensions 2.1 117-pin TFBGA Package (All dimensions in mm.) Doc. No. MV-S105540-00, Rev. A Page 42 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Package Mechanical Dimensions 117-pin TFBGA Package Table 16: 117-Pin TFBGA Package Dimensions Dim ens io ns i n mm Sy mbol MIN NOM MAX A -- -- 1.54 A1 0.40 0.50 0.60 A2 0.84 0.89 0.94 c 0.32 0.36 0.40 D 9.90 10.00 10.10 E 13.90 14.00 14.10 D1 -- 8.00 -- E1 -- 12.00 -- e -- 1.00 -- b 0.50 0.60 0.70 aaa 0.20 bbb 0.25 ccc 0.35 ddd 0.15 MD/ME NOTE: 1. CONTROLLING DIMENSION: MILLIMETER. 2. PRIMARY DATUM C AND SEATING PLANE ARE DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS. 3. DIMENSION b IS MEASURED AT THE MAXIMUM SOLDER BALL DIAMETER, PARALLEL TO PRIMARY DATUM C. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 43 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver 2.2 96-pin BCC Package - Top View - OBSOLETE - No Longer Available - Replaced by the 96-Pin aQFN Package Note The 96-Pin aQFN package is a pin compatible replacement for the 96-Pin BCC package. See Product Change Notification 1210066 and Table 20 for details. PIN 1 CORNER 9.000.10 75 74 95 1 C0.2 73 3 96 -p in 71 0.4000.05 Z X Y TOP VIEW 0.15 Z 0.6700.025 0.0750.025 0.20 0.80 MAX O B SO LE TE -N O LO N G ER Y 50 49 24 51 47 23 A25V 27 A IL A B LE 9.000.10 DETAIL "A" (1X) -R EP LA C ED by 0.08 M aQ FN Z X Y 0.08 M 0.300.05 96 X 0.05 Doc. No. MV-S105540-00, Rev. A Page 44 Z Z Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Package Mechanical Dimensions 96-Pin BCC Package - Bottom View - OBSOLETE - No Longer Available - Replaced 2.3 96-Pin BCC Package - Bottom View - OBSOLETE - No Longer Available - Replaced by the 96-Pin aQFN Package 3.50 ''A'' (PIN 1 CORNER) O -N 7.200 0.300.05 0.08 M Z X Y 8.20 9.00 DETAIL "B" (95X) BOTTOM VIEW Copyright (c) 2013 Marvell October 10, 2013 3.50 0.600.10 7.00 Z X Y "B" 0.400.05 0.2 R E NG O L A AV E -R D E AC L P 0.600 TYP. CL.(PKG.) 0.2 TE E OL S OB LE B A IL CL.(PKG.) 7.20 8.20 9.00 5.800 4.800 by n pi 96 FN Q a M 0.600 TYP. 0.08 0.600.10 4.100 4.100 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 45 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver 2.4 96-pin aQFN Package - Top View TOP VIEW PIN 1 CORNER A A2 C A1 C E B A D A3 C SECTIONC-C Doc. No. MV-S105540-00, Rev. A Page 46 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Package Mechanical Dimensions 96-Pin aQFN Package - Bottom View 2.5 96-Pin aQFN Package - Bottom View A15 A14 A13 A16 B13 B12 A17 B14 A18 B15 A19 B16 2.400 2.700 3.000 3.300 3.500 3.600 4.100 PKG. 4.500 A20 B17 A21 B18 A22 B19 A23 B20 A24 B21 A25 B22 A26 A27 B23 A28 A12 B11 B24 A11 A29 D2 B10 B25 B7 A7 B27 A32 B28 A33 C.L(PKG.) B6 B5 DETAIL "A" 2:1 (96X) B29 A34 E2 A6 B30 A5 A35 B4 B31 B3 B32 A4 A36 A3 A37 B2 B33 "A" A2 A38 B1 B34 B44 A1 A52 A51 B43 A50 B42 A49 B41 A48 B40 A47 B39 A46 B38 A45 B37 A44 B36 A43 B35 A42 A39 A41 eR A40 L 2.400 2.300 PIN 1 CORNER eR 2.400 2.700 2.800 2.900 3.000 3.300 3.500 3.600 4.100 PKG. 4.500 b1 C.L(PKG.) K1 B8 A8 A31 eT B26 B9 A9 0.000 b A30 A10 L 3.000 2.900 2.700 2.400 eT K PKG. 4.500 4.100 3.600 3.500 0.000 PKG. 4.500 4.100 3.600 3.500 3.300 3.000 2.700 2.400 BOTTOM VIEW Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 47 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Table 17: 96-Pin aQFN Package Dimensions Co ntr ol li ng Dim ens io n: MM Symbol MI N NO M MAX A -- -- 0.85 A3 0.020 0.050 0.080 A2 0.640 0.675 0.710 A1 0.120 0.130 0.140 b 0.250 0.300 0.350 b1 0.350 0.400 0.450 D D2 9.00 BSC 4.700 E E2 4.800 4.900 9.00 BSC 5.700 5.800 eT 0.600 eR 0.600 5.900 0.350 0.400 0.450 K1 0.850 0.900 0.950 L 0.150 0.200 0.250 K Tolerances of Form and Position aaa 0.150 bbb 0.100 ddd 0.050 ccc 0.080 eee 0.080 fff 0.100 Doc. No. MV-S105540-00, Rev. A Page 48 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Package Mechanical Dimensions 128-Pin PQFP Package 2.6 128-Pin PQFP Package 23.20 0.20 20.00 0.10 102 65 103 64 14.00 0.10 17.20 PIN1 INDICATOR 128 0.20 39 1 38 1.6 Nominal 3.40 Max 0.25 min 0.22 0.05 0.88 0.15 0.5 Basic Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 49 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Section 3. Order Information 3.1 Ordering Part Numbers and Package Markings Figure 6 shows the ordering part numbering scheme for the 88E1111 devices. Contact Marvell(R) FAEs or sales representatives for complete ordering information. Figure 6: Sample Part Number 88E1111 - xx - xxx - Cxxx - xxxx Custom Code (optional) Part Number 88E1111 Cus t om Code Custom Code Temperature Range C = Commercial I = Industrial Package Code BAB = 117-pin TFBGA CAA = 96-pin BCC (OBSOLETE - No Longer Available - The 96-Pin aQFN package is a pin compatible replacement for the 96-Pin BCC package. See Product Change Notification 1210066 and Table 20 for details. NDC = 96-pin aQFN RCJ - 128-pin PQFP Table 18: Environmental "-" = RoHS 5/6 compliant package 1 = RoHS 6/6 compliant package 2 = Green NOTE: RoHS 5/6 compliant packages are no longer available. 88E1111 Part Order Options - RoHS 6/6 Compliant Package Pa ckag e Ty pe Part Ord er Nu mb er 88E1111 117-pin TFBGA - Commercial 88E1111-XX-BAB1C000 88E1111 117-pin TFBGA - Industrial 88E1111-XX-BAB1I000 88E1111 96-pin BCC - Commercial (OBSOLETE - no longer available - replaced by 96-pin aQFN) 88E1111-XX-CAA1C000 88E1111 96-pin BCC - Industrial (OBSOLETE - no longer available - replaced by 96-pin aQFN) 88E1111-XX-CAA1I000 88E1111 128-pin PQFP - Commercial 88E1111-XX-RCJ1C000 Table 19: 88E1111 Part Order Options - Green Compliant Package Pa ckag e Ty pe Part Ord er Nu mb er 88E1111 96-pin aQFN Commercial 88E1111-XX-NDC2C000 88E1111 96-pin aQFN Industrial 88E1111-XX-NDC2I000 Doc. No. MV-S105540-00, Rev. A Page 50 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Order Information Ordering Part Numbers and Package Markings Table 20: 96-pin BCC Package Replacement Part Numbers Existing 96 -pin BCC Pac kage Pa rt Number Rec omm ended 9 6-pin aQFN Pa ckage Rep l acem ent Part Nu mbe r 88E1111-B0-CAA-C000 88E1111-B0-NDC2C000 88E1111-B0-CAA1C000 88E1111-B0-NDC2C000 88E1111-B2-CAA-C000 88E1111-B2-NDC2C000 88E1111-B2-CAA-I000 88E1111-B2-NDC2I000 88E1111-B2-CAA1C000 88E1111-B2-NDC2C000 88E1111-B2-CAA1I000 88E1111-B2-NDC2I000 3.1.1 RoHS 5/6 Compliant Marking Examples Figure 7 is an example of the package marking and pin 1 location for the 88E1111 117-pin TFBGA commercial RoHS 5/6 compliant package. Figure 7: 88E1111 117-pin TFBGA Commercial RoHS 5/6 Compliant Package Marking and Pin 1 Location Logo 88E1111-BAB Country of origin (Contained in the mold ID or marked as the last line on the package.) Lot Number YYWW xx@ Country Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 51 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Figure 8 is an example of the package marking and pin 1 location for the 88E1111 117-pin TFBGA Industrial RoHS 5/6 compliant package. Figure 8: 88E1111 117-pin TFBGA Industrial RoHS 5/6 Compliant Package Marking and Pin 1 Location L o go 88E1111-BAB Country of origin (Contained in the mold ID or marked as the last line on the package.) Lot Number YYWW xx@ Country Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 I Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Industrial Grade Package Marking Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Figure 9 is an example of the package marking and pin 1 location for the 88E1111 128-pin PQFP Commercial RoHS 5/6 compliant package. Figure 9: 88E1111 128-pin PQFP Commercial RoHS 5/6 Compliant Package Marking and Pin 1 Location L o go 88E1111-RCJ Country of origin (Contained in the mold ID or marked as the last line on the package.) Lot Number YYWW xx@ Country Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Doc. No. MV-S105540-00, Rev. A Page 52 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Order Information Ordering Part Numbers and Package Markings 3.1.2 RoHS 6/6 Compliant Marking Examples Figure 10 is an example of the package marking and pin 1 location for the 88E1111 117-pin TFBGA commercial RoHS 6/6 compliant package. Figure 10: 88E1111 117-pin TFBGA Commercial RoHS 6/6 Compliant Package Marking and Pin 1 Location Logo 88E1111-BAB1 Country of origin (Contained in the mold ID or marked as the last line on the package.) Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 Lot Number YYWW xx@ Country Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Figure 11 is an example of the package marking and pin 1 location for the 88E1111 117-pin TFBGA industrial RoHS 6/6 compliant package. Figure 11: 88E1111 117-pin TFBGA Industrial RoHS 6/6 Compliant Package Marking and Pin 1 Location Logo 88E1111-BAB1 Country of origin (Contained in the mold ID or marked as the last line on the package.) Lot Number YYWW xx@ Country Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 I Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Industrial Grade Package Marking Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 53 88E1111 Product Brief Integrated 10/100/1000 Ultra Gigabit Ethernet Transceiver Figure 12 is an example of the package marking and pin 1 location for the 88E1111 128-pin PQFP Commercial RoHS 6/6 compliant package. Figure 12: 88E1111 128-pin PQFP Commercial RoHS 6/6 Compliant Package Marking and Pin 1 Location Logo 88E1111-RCJ1 Country of origin (Contained in the mold ID or marked as the last line on the package.) Lot Number YYWW xx@ Country Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Doc. No. MV-S105540-00, Rev. A Page 54 Copyright (c) 2013 Marvell Document Classification: Proprietary Information October 10, 2013 Order Information Ordering Part Numbers and Package Markings 3.1.3 Green Compliant Marking Examples Figure 13 is an example of the package marking and pin 1 location for the 88E1111 96-pin aQFN Commercial Green compliant package. Figure 13: 88E1111 96-pin aQFN Commercial Green Compliant Package Marking and Pin 1 Location L o go 88E1111-NDC2 Country of origin (Contained in the mold ID or marked as the last line on the package.) Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 Lot Number YYWW xx@ Country 2 = Green Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Figure 14 is an example of the package marking and pin 1 location for the 88E1111 96-pin aQFN Industrial Green compliant package. Figure 14: 88E1111 96-pin aQFN Industrial Green Compliant Package Marking and Pin 1 Location L o go 88E1111-NDC2 Country of origin (Contained in the mold ID or marked as the last line on the package.) Lot Number YYWW xx@ Country Part number, package code, environmental code Environmental Code - No code = RoHS 5/6 1 = RoHS 6/6 2 = Green I Date code, custom code, assembly plant code YYWW xx = Date code = Custom code @ = Assembly location code Industrial Grade Package Marking Pin 1 location Note: The above example is not drawn to scale. Location of markings is approximate. Copyright (c) 2013 Marvell October 10, 2013 Doc. No. MV-S105540-00, Rev. A Document Classification: Proprietary Information Page 55 Back Cover Marvell Semiconductor, Inc. 5488 Marvell Lane Santa Clara, CA 95054, USA Tel: 1.408.222.2500 Fax: 1.408.988.8279 www.marvell.com Marvell. Moving Forward Faster