Enpirion(R) Power Datasheet EN5329QI 2A PowerSoC Low Profile Synchronous Buck DC-DC Converter with Integrated Inductor Description Features The EN5329QI is a highly integrated, low profile, highly efficient, 2A synchronous buck power system on a chip (PowerSoCTM). The device features an advance integrated inductor, integrated MOSFETs, a PWM voltage-mode controller, and internal compensation providing the smallest possible solution size. The EN5329QI is a member of the EN53x9QI family of pin compatible and interchangeable devices. The pin compatibility enables an easy to use scalable family of products covering the load range from 1.5A up to 3A in a low profile 4mm x 6mm x 1.1mm QFN package. The EN5329QI operates at high switching frequency and allows for the use of tiny MLCC capacitors. It also enables a very wide control loop bandwidth providing excellent transient performance and reduced output impedance. The internal compensation is designed for unconditional stability across all operating conditions. Altera Enpirion integrated inductor solution significantly helps to reduce noise. The complete power converter solution enhances productivity by offering greatly simplified board design, layout and manufacturing requirements. All Altera Enpirion products are RoHS compliant and lead-free manufacturing environment compatible. Integrated Inductor Solution Footprint as Small as 50 mm2 Low Profile, 1.1mm High Reliability Solution: 42,000 Years MTBF High Efficiency, up to 95 % Low Output Ripple Voltage; <5mVP-P Typical 2.4 V to 5.5 V Input Voltage Range 2A Continuous Output Current Capability Pin Compatible w/ EN5319 1.5A and EN5339 3A Output Enable and Power OK Signal Under Voltage Lockout, Over Current, Short Circuit, and Thermal Protection RoHS Compliant; Halogen Free; 260C Reflow Applications Applications with Low Profile Requirement such as SSD and Embedded Computing SAN/NAS Accelerator Appliances Controllers, Raid, Processors, Network Processors, DSPs' FPGAs, and ASICs Noise Sensitive Applications Efficiency vs. Output Current 100 100k 90 POK VOUT COUT PVIN TST0 TST1 CIN 22F EN5329QI Ca TST2 PGND AVIN 1F EFFICIENCY (%) ENABLE POK VIN VOUT AGND Ra VFB PGND 2x 22F or 1x 47F Rb 80 70 60 50 Actual Solution Size 50mm2 CONDITIONS VIN = 3.3V 40 30 VOUT = 2.5V 20 VOUT = 1.2V 10 0 0 Figure 1. Simplified Applications Circuit 2 Figure 2. Highest Efficiency in Smallest Solution Size 1 08326 0.5 1 1.5 OUTPUT CURRENT (A) June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Ordering Information Part Number EN5329QI EVB-EN5329QI Package Markings EN5329 EN5329 Temp Rating (C) -40 to +85 Package Description 24-pin (4mm x 6mm x 1.1mm) QFN T&R QFN Evaluation Board Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html Pin Assignments (Top View) NC(SW) NC(SW) NC(SW) NC(SW) PVIN PVIN ENABLE POK 24 23 22 21 20 19 18 17 Keep-Out NC(SW) 1 PGND 2 25 PGND 16 AVIN 15 AGND 26 PGND PGND 3 14 VFB Keep-Out VOUT 4 10 11 12 TST1 TST0 PGND 9 TST2 8 PGND 7 VOUT VOUT 6 VOUT 5 13 NC Figure 3: Pin Out Diagram (Top View) NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. NOTE B: Grey area highlights exposed metal on the bottom of the package that is not to be mechanically or electrically connected to the PCB. There should be no traces on PCB top layer under these keep out areas. NOTE C: White `dot' on top left is pin 1 indicator on top of the device package. Pin Description PIN NAME 1, 21-24 NC(SW) 2-3, 8-9 PGND 4-7 VOUT 10 11 TST2 TST1 FUNCTION NO CONNECT: These pins are internally connected to the common switching node of the internal MOSFETs. They must be soldered to PCB but not be electrically connected to any external signal, ground, or voltage. Failure to follow this guideline may result in device damage. Input and output power ground. Connect these pins to the ground electrode of the input and output filter capacitors. See VOUT, PVIN descriptions and Layout Recommendation for more details. Regulated converter output. Connect to the load and place output filter capacitor(s) between these pins and PGND pins 8 and 9. See layout recommendation for details Test Pin. For Altera internal use only. Connect to AVIN at all times. Test Pin. For Altera internal use only. Connect to AVIN at all times. 2 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI PIN 12 NAME TST0 13 NC 14 VFB 15 AGND 16 AVIN 17 POK 18 ENABLE 19-20 PVIN 25,26 PGND FUNCTION Test Pin. For Altera internal use only. Connect to AVIN at all times. NO CONNECT: This pin must be soldered to PCB but not electrically connected to any other pin or to any external signal, voltage, or ground. This pin may be connected internally. Failure to follow this guideline may result in device damage. This is the external feedback input pin. A resistor divider connects from the output to AGND. The mid-point of the resistor divider is connected to VFB. A feed-forward capacitor is required parallel to the upper feedback resistor (RA). The output voltage regulation is based on the VFB node voltage equal to 0.600V. The quiet ground for the control circuits. Connect to the ground plane with a via right next to the pin. Analog input voltage for the control circuits. Connect this pin to the input power supply (PVIN) at a quiet point. Decouple with a 1uF capacitor to AGND. POK is an open drain output. Refer to Power OK section for details. Leave POK open if unused. Output Enable. A logic high level on this pin enables the output and initiates a soft-start. A logic low signal disables the output and discharges the output to GND. This pin must not be left floating. Input power supply. Connect to input power supply and place input filter capacitor(s) between these pins and PGND pins 2 to 3. Not a perimeter pin. Device thermal pad to be connected to the system GND plane for heatsinking purposes. See Layout Recommendation section. 3 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Absolute Maximum Ratings CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond the recommended operating conditions is not implied. Stress beyond the absolute maximum ratings may impair device life. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. PARAMETER SYMBOL MIN MAX UNITS Voltages on : PVIN, AVIN, VOUT -0.3 6.5 V Voltages on: ENABLE, POK, TST0, TST1, TST2 -0.3 VIN+0.3 V Voltages on: VFB -0.3 2.7 V -65 150 C 150 C Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020A 260 C ESD Rating (Human Body Model) 2000 V ESD Rating (Charge Device Model) 500 V Storage Temperature Range TSTG Maximum Operating Junction Temperature TJ-ABS Max Recommended Operating Conditions PARAMETER SYMBOL MIN MAX UNITS VIN 2.4 5.5 V Output Voltage Range (Note 1) VOUT 0.6 VIN - VDO V Output Current IOUT 0 2 A Operating Ambient Temperature TA -40 +85 C Operating Junction Temperature TJ -40 +125 C Input Voltage Range Thermal Characteristics PARAMETER SYMBOL TYP UNITS Thermal Resistance: Junction to Ambient (0 LFM) (Note 2) JA 36 C/W Thermal Resistance: Junction to Case (0 LFM) JC 6 C/W Thermal Shutdown TSD 150 C Thermal Shutdown Hysteresis TSDH 15 C Note 1: VDO (dropout voltage) is defined as (ILOAD x Dropout Resistance). Please see Electrical Characteristics Table. Note 2: Based on 2oz. external copper layers and proper thermal design in line with EIJ/JEDEC JESD51-7 standard for high thermal conductivity boards. 4 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Electrical Characteristics NOTE: VIN = 5V, Minimum and Maximum values are over operating ambient temperature range unless otherwise noted. Typical values are at TA = 25C. PARAMETER Operating Input Voltage Feedback Node Initial Accuracy Output Variation (Note 3) (Line, Load, Temperature) VFB, ENABLE, TST0/1/2 Pin Input Current (Note 4) Shutdown Current Under Voltage Lock-out - VIN Rising Under Voltage Lock-out - tVIN Falling Soft-start Time SYMBOL VIN VVFB VOUT VUVLOR VUVLOF TEST CONDITIONS TA = 25C; VIN = 5V ILOAD = 100 mA 2.4V VIN 5.5V 0 ILOAD 2A ENABLE Low Voltage Above Which UVLO is Not Asserted Voltage Below Which UVLO is Asserted Time from Enable High (Note 4) MIN 2.4 0.588 Output Ripple Voltage Logic Low Logic High VOUT Rising VOUT Falling ISINK = 1 mA 0.91 2.4V VIN 5.5V FOSC COUT = 2 x 22 F 0603 X5R MLCC, VOUT = 3.3 V, ILOAD = 2A COUT = 2 x 22 F 0603 X5R MLCC, VOUT = 1.8 V, ILOAD = 2A 3.2 MAX 5.5 UNITS V 0.612 V +3 % +/-40 nA 20 A 2.2 V 2.1 V 1.40 1.89 ms 150 300 m 0.4 VIN V 0.0 1.4 POK High VRIPPLE 0.600 -3 Dropout Resistance ENABLE Voltage Threshold POK Threshold POK Threshold POK Low Voltage POK Pin VOH Leakage Current Current Limit Threshold Operating Frequency TYP 92 90 0.15 0.4 % % V 0.5 2 A 5 3.2 A MHz 5 mVP-P 5 mVP-P Note 3: Output voltage variation is based on using 0.1% accuracy resistor values. Note 4: Parameter not production tested but is guaranteed by design. 5 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Typical Performance Curves Efficiency vs. Output Current 100 90 90 80 80 EFFICIENCY (%) EFFICIENCY (%) Efficiency vs. Output Current 100 70 60 50 VOUT = 2.5V 40 VOUT = 1.8V 30 VOUT = 1.2V 20 CONDITIONS VIN = 3.3V VOUT = 1.0V 10 0 70 60 50 VOUT = 3.3V 40 VOUT = 2.5V 30 VOUT = 1.8V 20 VOUT = 1.2V 10 VOUT = 1.0V 0 0 0.5 1 1.5 2 0 OUTPUT CURRENT (A) 1.5 2 3.36 IOUT = 1A 3.5 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1 Output Voltage vs. Output Current Dropout Voltage IOUT = 2A 3.4 3.3 3.2 3.1 3 CONDITIONS VOUT = 3.3V 2.9 2.8 VOUT = 3.3V 3.34 3.32 3.3 3.28 CONDITIONS VIN = 5V 3.26 3.24 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4 0 0.5 1 1.5 2 INPUT VOLTAGE(V) OUTPUT CURRENT (A) Output Voltage vs. Output Current Output Voltage vs. Output Current 2.56 1.86 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 0.5 OUTPUT CURRENT (A) 3.6 VOUT = 2.5V 2.54 2.52 2.5 2.48 CONDITIONS VIN = 5V 2.46 2.44 VOUT = 1.8V 1.84 1.82 1.8 1.78 CONDITIONS VIN = 5V 1.76 1.74 0 0.5 1 1.5 2 0 OUTPUT CURRENT (A) 0.5 1 1.5 2 OUTPUT CURRENT (A) 6 08326 CONDITIONS VIN = 5V June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Typical Performance Curves (Continued) Output Voltage vs. Output Current Output Voltage vs. Output Current 2.56 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.26 VOUT = 1.2V 1.24 1.22 1.2 1.18 CONDITIONS VIN = 5V 1.16 VOUT = 2.5V 2.54 2.52 2.5 2.48 CONDITIONS VIN = 3.3V 2.46 2.44 1.14 0 0.5 1 1.5 0 2 0.5 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 2 1.26 VOUT = 1.8V 1.84 1.82 1.8 1.78 CONDITIONS VIN = 3.3V 1.76 1.74 VOUT = 1.2V 1.24 1.22 1.2 1.18 CONDITIONS VIN = 3.3V 1.16 1.14 0 0.5 1 1.5 2 0 0.5 OUTPUT CURRENT (A) 1.815 1.815 OUTPUT VOLTAGE (V) 1.820 1.810 1.805 1.800 1.795 CONDITIONS Load = 5mA 1.785 1.5 2 Output Voltage vs. Input Voltage 1.820 1.790 1 OUTPUT CURRENT (A) Output Voltage vs. Input Voltage OUTPUT VOLTAGE (V) 1.5 Output Voltage vs. Output Current Output Voltage vs. Output Current 1.86 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 500mA 1.785 1.780 1.780 2.5 3.1 3.7 4.3 INPUT VOLTAGE (V) 4.9 2.5 5.5 7 08326 1 OUTPUT CURRENT (A) OUTPUT CURRENT (A) June 3, 2016 3.1 3.7 4.3 INPUT VOLTAGE (V) 4.9 5.5 www.altera.com/enpirion Rev E EN5329QI Typical Performance Curves (Continued) Output Voltage vs. Input Voltage 1.820 1.815 1.815 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) Output Voltage vs. Input Voltage 1.820 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 1A 1.785 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 2A 1.785 1.780 1.780 2.5 3.1 3.7 4.3 INPUT VOLTAGE (V) 4.9 5.5 2.5 1.840 1.030 1.830 1.020 1.010 1.000 0.990 0.980 LOAD = 2A 0.970 LOAD = 100mA CONDITIONS VIN = 5V VOUT_NOM = 1.0V 5.5 1.810 1.800 1.790 1.780 1.770 LOAD = 100mA CONDITIONS VIN = 5V VOUT_NOM = 1.8V 1.760 -40 -15 10 35 60 AMBIENT TEMPERATURE ( C) 85 -40 GUARANTEED OUTPUT CURRENT (A) 3.5 3 2.5 2 1.5 1 CONDITIONS Conditions VIN VIN == 5.0V 5.0V VOUT VOUT = 1.0V = 3.3V 0.5 0 -40 -15 10 35 60 AMBIENT TEMPERATURE( C) -15 10 35 60 AMBIENT TEMPERATURE ( C) 85 No Thermal Derating No Thermal Derating GUARANTEED OUTPUT CURRENT (A) 4.9 1.820 LOAD = 2A 0.960 85 8 08326 3.7 4.3 INPUT VOLTAGE (V) Output Voltage vs. Temperature 1.040 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) Output Voltage vs. Temperature 3.1 June 3, 2016 3.5 3 2.5 2 1.5 1 CONDITIONS Conditions VIN VIN == 5.0V 5.0V VOUT VOUT = 3.3V = 3.3V 0.5 0 -40 -15 10 35 60 AMBIENT TEMPERATURE( C) 85 www.altera.com/enpirion Rev E EN5329QI Typical Performance Characteristics (Continued) Output Ripple at 20MHz Output Ripple at 20MHz VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 3.3V VOUT = 1.8V IOUT = 2A CIN = 1x 22F (0805) COUT = 2 x 22F (0603) CONDITIONS VIN = 5V VOUT = 3.3V IOUT = 2A CIN = 1x 22F (0805) COUT = 2 x 22F (0603) Output Ripple at 500MHz Output Ripple at 500MHz VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 3.3V VOUT = 1.8V IOUT = 2A CIN = 1x 22F (0805) COUT = 2 x 22F (0603) CONDITIONS VIN = 5V VOUT = 3.3V IOUT = 2A CIN = 1x 22F (0805) COUT = 2 x 22F (0603) Startup Waveforms at 2A Startup Waveforms at 0A ENABLE ENABLE VOUT VOUT POK POK LOAD LOAD VIN = 5V, VOUT = 1.8V CIN = 1 X 22F (0805), COUT = 2 x 22F (0603), IOUT = 0A VIN = 5V, VOUT = 1.8V CIN = 1 X 22F (0805), COUT = 2 x 22F (0603), IOUT = 2A 9 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Typical Performance Characteristics (Continued) Load Transient from 0 to 1A Load Transient from 0 to 2A VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 3.3V VOUT = 1.8V CIN = 1 X 22F (0805) COUT = 2 x 22F (0603) CONDITIONS VIN = 3.3V VOUT = 1.8V CIN = 1 X 22F (0805) COUT = 2 x 22F (0603) LOAD LOAD Load Transient from 0 to 1A Load Transient from 0 to 2A VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 5V VOUT = 2.5V CIN = 1 X 22F (0805) COUT = 2 x 22F (0603) LOAD LOAD 10 08326 June 3, 2016 CONDITIONS VIN = 5V VOUT = 2.5V CIN = 1 X 22F (0805) COUT = 2 x 22F (0603) www.altera.com/enpirion Rev E EN5329QI Functional Block Diagram PVIN POK UVLO POK Thermal Limit Current Limit ENABLE NC (SW) Soft Start P-Drive Logic (-) VOUT PWM Comp (+) N-Drive PGND Sawtooth Generator Compensation Network VFB (-) Error Amp (+) DAC VREF BIAS Package Boundary TST AVIN AGND Figure 4: Functional Block Diagram Functional Description impedance and excellent load transient response. The EN5329QI features include Power OK, under voltage lockout (UVLO), over current protection, short circuit protection, and thermal overload protection. Overview The EN5329QI is a highly integrated synchronous buck converter with an internal inductor utilizing advanced CMOS technology to provide high switching frequency, while also maintaining high efficiency. The EN5329QI is a high power density device packaged in a tiny 4x6x1.1mm 24-pin QFN package. Its high switching frequency allows for the use of very small MLCC input and output filter capacitors and results in a total solution size as small as 50mm2. The EN5329QI is a member of a family of pin compatible devices. This offers scalability for applications where load currents may not be known apriori, and/or speeds time to market with a convenient common solution footprint. The EN5329QI buck converter uses Type III voltage mode control to provide pin-point output voltage accuracy, high noise immunity, low output Stability and Compensation The EN5329QI utilizes an internal compensation network that is designed to provide stable operation over a wide range of operating conditions. The output compensation circuit may be customized to improve transient performance or reduce output voltage ripple with dynamic loads. Soft-Start The EN5329QI has an internal soft-start circuit that controls the ramp of the output voltage. The control circuitry limits the VOUT ramp rate to levels that are safe for the Power MOSFETs and the integrated inductor. 11 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI The EN5329QI has a constant startup up time which is independent of the VOUT setting. The output rising slew rate is proportional to the output voltage. The startup time is approximately 1.4ms from when the ENABLE is first pulled high until VOUT reaches the regulated voltage level. Excess bulk capacitance on the output of the device can cause an over-current condition at startup. Maximum allowable output capacitance depends on the device's minimum current limit as indicated in the Electrical Characteristics Table, the output current at startup, the minimum soft-start time also in the Electrical Characteristics Table and the output voltage. The total maximum capacitance on the output rail is estimated by the equation below: turns on and limits the discharge current to 300 mA or below. The ENABLE pin should not be left floating as it could be in an unknown and random state. It is recommended to enable the device after both PVIN and AVIN is in regulation. At extremely cold conditions below -30C, the controller may not be properly powered if ENABLE is tied directly to AVIN during startup. It is recommended to use an external RC circuit to delay the ENABLE voltage rise so that the internal controller has time to startup into regulation (see circuit below). The RC circuit may be adjusted so that AVIN and PVIN are above UVLO before ENABLE is high. The startup time will be delayed by the extra time it takes for the capacitor voltage to reach the ENABLE threshold. AVIN COUT_MAX = 0.7 * (ILIMIT - IOUT) * tSS / VOUT COUT_MAX = maximum allowable output capacitance ILIMIT = minimum current limit = 3.2A IOUT = output current at startup tSS = minimum soft-start time = 0.91ms VOUT = output voltage 1k ENABLE NOTE:Device stability still needs to be verified in the application if extra bulk capacitors are added to the output rail. 1F Over Current/Short Circuit Protection When an over current condition occurs, VOUT is pulled low and the device disables switching internally. This condition is maintained for a period of 1.2 ms and then a normal soft-start cycle is initiated. If the over current condition still persists, this cycle will repeat. Figure 5: ENABLE Delay Circuit Thermal Shutdown Under Voltage Lockout An under voltage lockout circuit will hold off switching during initial power up until the input voltage reaches sufficient level to ensure proper operation. If the voltage drops below the UVLO threshold the lockout circuitry will again disable switching. Hysteresis is included to prevent chattering between UVLO high and low states. When excessive power is dissipated in the device, its junction temperature rises. Once the junction temperature exceeds the thermal shutdown temperature of 150C, the thermal shutdown circuit turns off the converter, allowing the device to cool. When the junction temperature drops 15C, the device will be re-enabled and go through a normal startup process. Enable Power OK The ENABLE pin provides means to shut down the converter or initiate normal operation. A logic high on the ENABLE pin will initiate the converter to start the soft-start cycle and regulate the output voltage to the desired value. A logic low will allow the device to discharge the output and go into shutdown mode for minimal power consumption. When the output is discharged, an auxiliary NFET The Power OK (POK) feature is an open drain output signal used to indicate if the output voltage is within 92% of the set value. Within this range, the POK output is allowed to be pulled high. Outside this range, the POK output is maintained low. During transitions such as power up and power down, the POK output will not change state until the transition is complete for enhanced noise immunity. 12 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Pre-Bias Start-up The POK has 1mA sink capability. When POK is pulled high, the worst case pin leakage current is as low as 500nA over temperature. This allows a large pull up resistor such as 100k to be used for minimal current consumption in shutdown mode. The POK output can also be conveniently used as an enable input of the next stage for power sequencing of multiple converters. The EN5339QI does not support startup into a prebiased condition. Be sure the output capacitors are not charged or the output of the EN5339QI is not pre-biased when the EN5339QI is first enabled. Power-Up/Down Sequencing During power-up, ENABLE should not be asserted before PVIN, and PVIN should not be asserted before AVIN. The PVIN should never be powered when AVIN is off. During power down, the AVIN should not be powered down before the PVIN. Tying PVIN and AVIN or all three pins (AVIN, PVIN, ENABLE) together during power up or power down meets these requirements. 13 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Application Information capacitors. Y5V or equivalent dielectrics lose too much capacitance with frequency, DC bias, and temperature. Therefore, they are not suitable for switch-mode DC-DC converter filtering, and must be avoided. Setting the Output Voltage The EN5329 uses a simple and flexible resistor divider network to program the output voltage. A feed-forward capacitor (Ca) is used to ensure the stability of the converter. Table 3 shows the required critical component values as a function of VOUT. It is recommended to use 1% or better feedback resistors to ensure output voltage accuracy. The Ra resistor value is fixed at 348k as shown in Table 3. Based on that value, the bottom resistor Rb can be calculated below as: Rb Table 1: Recommended Input Capacitors Description MFG P/N 22F, 10V, X5R, 0805 Taiyo Yuden LMK212BBJ226MG-T Murata GRM21BR61A226ME51 Output Filter Capacitor Selection The EN5329QI output capacitor selection may be determined based on two configurations. Table 3 provides the allowed output capacitor configurations based on operating conditions. For lower output ripple, choose 2 x 22F for the output capacitors. For smaller solution size, use one 47F output capacitor. Table 2 shows the recommended type and brand of output capacitors to use. Ra 0.6 V VOUT 0.6 V The VOUT is the nominal output voltage. The Rb and Ra resistors have the same units based on the above equation. 100k POK ENABLE POK VIN COUT PVIN TST0 TST1 CIN 22F EN5329QI Ca TST2 PGND AVIN In some rare applications modifications to the compensation may be required. The EN5329QI provides the capability to modify the control loop response to allow for customization for specific applications. VOUT VOUT AGND Ra VFB PGND 1F 2x 22F or 1x 47F Rb Table 2: Recommended Output Capacitors Figure 6. Typical Application Circuit. (NOTE: Enable can be separated from PVIN if the application requires it) MFG P/N 47F, 6.3V, X5R, 0805 Taiyo Yuden JMK212BBJ476MG-T Murata GRM21BR60J476ME15 22F, 6.3V, X5R, 805 Taiyo Yuden JMK212ABJ226MG Murata GRM21BR60J226ME39 Murata GRM188R60J226MEA0 22F, 6.3V, X5R, 0603 AVIN Filter Capacitor A 1.0 F, 10V, 0402 MLCC capacitor should be placed between AVIN and AGND as close to the pins as possible. This will provide high frequency bypass to ensure clean chip supply for optimal performance. Table 3. Required Critical Components (Note: Follow Layout Recommendations) Input Filter Capacitor Selection A single 22F, 0805 MLCC capacitor is needed on PVIN for all applications. Connect the input capacitor between PVIN and PGND as close to the pins as possible. Placement of the input capacitor is critical to ensure low conducted and radiated EMI. Low ESR MLCC capacitors with X5R or X7R or equivalent dielectric should be used for the input 14 08326 Description June 3, 2016 VOUT (V) Ca (pF) Vout 2.5V 8.2 2.5V < Vout 3.3V 6.8 Vout 2.5V 8.2 2.5V < Vout 3.3V 6.8 Vout 2.5V 8.2 2.5V < Vout 3.3V 6.8 Vout > 3.3V 6.8 Ra (k) Cout (F) 348 1x47uF/0805 348 2x22uF/0603 348 2x22uF/0805 www.altera.com/enpirion Rev E EN5329QI Thermal Considerations For VIN = 5V, VOUT = 3.3V at 2A, 92% Thermal considerations are important power supply design facts that cannot be avoided in the real world. Whenever there are power losses in a system, the heat that is generated needs to be accounted for. Altera's Enpirion PowerSoCTM helps alleviate some of those concerns. Altera's Enpirion EN5329QI DC-DC converter is packaged in a 4x6x1.1mm 24-pin QFN package. The QFN package is constructed with exposed thermal pads on the bottom of the package. The exposed thermal pad should be soldered directly on to a copper ground pad on the printed circuit board (PCB) to act as a heat sink. The recommended maximum junction temperature for continuous operation is 125C. Continuous operation above 125C may reduce long-term reliability. The device has a thermal overload protection circuit designed to turn off the device at an approximate junction temperature value of 150C. The EN5329QI is guaranteed to support the full 2A output current up to 85C ambient temperature. The following example and calculations illustrate the thermal performance of the EN5329QI. Example: = POUT / PIN = 92% = 0.92 PIN = POUT / PIN 6.6W / 0.92 7.2W The power dissipation (PD) is the power loss in the system and can be calculated by subtracting the output power from the input power. PD = PIN - POUT 7.2W - 6.6W 0.6W With the power dissipation known, the temperature rise in the device may be estimated based on the theta JA value (JA). The JA parameter estimates how much the temperature will rise in the device for every watt of power dissipation. The EN5329QI has a JA value of 36 C/W without airflow. Determine the change in die temperature (T) based on PD and JA. T = PD x JA T 0.6W x 36C/W = 21.6 C 22C VOUT = 3.3V The junction temperature (TJ) of the device is approximately the ambient temperature (TA) plus the change in temperature. We assume the initial ambient temperature to be 25C. IOUT = 2A TJ = TA + T First calculate the output power. TJ 25 C + 22C 47C POUT = 3.3V x 2A = 6.6W The maximum operating junction temperature (TJMAX) of the device is 125C, so the device can operate at a higher ambient temperature. The maximum ambient temperature (TAMAX) allowed can be calculated. VIN = 5V Next, determine the input power based on the efficiency () shown in Figure 6. 100 90 TAMAX = TJMAX - PD x JA EFFICIENCY (%) 80 125 C - 22C 103C ~92% 70 60 The ambient temperature can actually rise by another 78C, bringing it to 103C before the device will reach TJMAX. This indicates that the EN5329QI can support the full 2A output current range up to approximately 103C ambient temperature given the input and output voltage conditions. Note that the efficiency will be slightly lower at higher temperatures and these calculations are estimates. 50 40 30 20 CONDITIONS VIN = 5V VOUT = 3.3V 10 0 0 0.5 1 1.5 2 OUTPUT CURRENT (A) Figure 7: Efficiency vs. Output Current 15 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Engineering Schematic Figure 8. Engineering Schematic with Critical Components 16 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Layout Recommendations ground plane through as many vias as possible. The drill diameter of the vias should be 0.33mm, and the vias must have at least 1 oz. copper plating on the inside wall, making the finished hole size around 0.20-0.26mm. Do not use thermal reliefs or spokes to connect the vias to the ground plane. This connection provides the path for heat dissipation from the converter. Recommendation 4: Multiple small vias (the same size as the thermal vias discussed in recommendation 3) should be used to connect ground terminal of the input capacitor and output capacitors to the system ground plane. It is preferred to put these vias along the edge of the GND copper closest to the +V copper. These vias connect the input/output filter capacitors to the GND plane, and help reduce parasitic inductances in the input and output current loops. Recommendation 5: AVIN is the power supply for the small-signal control circuits. It should be connected to the input voltage at a quiet point. In Figure 9 this connection is made at the input capacitor. Place a 1F capacitor from the AVIN pin to AGND right next to device pins. Recommendation 6: The layer 1 metal under the device must not be more than shown in Figure 8. See the section regarding exposed metal on bottom of package. As with any switch-mode DC/DC converter, try not to run sensitive signal or control lines underneath the converter package on other layers. Recommendation 7: The VOUT sense point should be just after the last output filter capacitor. Keep the sense trace short in order to avoid noise coupling into the node. Recommendation 8: Keep RA, CA, RB close to the VFB pin (See Figures 6). The VFB pin is a highimpedance, sensitive node. Keep the trace to this pin as short as possible. Whenever possible, connect RB directly to the AGND pin instead of going through the GND plane. Recommendation 9: Altera provides schematic and layout reviews for all customer designs. Please contact local sales representatives for references to Power Applications support (www.altera.com/mysupport). Figure 9. Optimized Layout Recommendations This layout only shows the critical components and top layer traces for minimum footprint with ENABLE as a separate signal. Alternate ENABLE configurations & the POK pin need to be connected and routed according to customer application. Please see the Gerber files on EN5329QI's product page at www.altera.com/enpirion for details on all layers. Recommendation 1: Input and output filter capacitors should be placed on the same side of the PCB, and as close to the EN5329QI package as possible. They should be connected to the device with very short and wide traces. Do not use thermal reliefs or spokes when connecting the capacitor pads to the respective nodes. The +V and GND traces between the capacitors and the EN5329QI should be as close to each other as possible so that the gap between the two nodes is minimized, even under the capacitors. Recommendation 2: The system ground plane should be the first layer immediately below the surface layer. This ground plane should be continuous and un-interrupted below the converter and the input/output capacitors. Recommendation 3: The thermal pad underneath the component must be connected to the system 17 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Design Considerations for Lead-Frame Based Modules Exposed Metal Pads on Package Bottom QFN lead-frame based package technology utilizes exposed metal pads on the bottom of the package that provide improved thermal dissipation, lower package thermal resistance, smaller package footprint and thickness, larger lead size and pitch, and excellent lead co-planarity. As the EN5329 package is a fully integrated module consisting of multiple internal devices, the lead-frame provides circuit interconnection and mechanical support of these devices resulting in multiple exposed metal pads on the package bottom. Only the two large thermal pads and the perimeter leads are to be mechanically/electrically connected to the PCB through a SMT soldering process. All other exposed metal is to remain free of any interconnection to the PCB. Figure 9 shows the recommended PCB metal layout for the EN5329 package. A GND pad with a solder mask "bridge" to separate into two pads and 24 signal pads are to be used to match the metal on the package. The PCB should be clear of any other metal, including traces, vias, etc., under the package to avoid electrical shorting. The Solder Stencil Aperture should be smaller than the PCB ground pad. This will prevent excess solder from causing bridging between adjacent pins or other exposed metal under the package. Please consult EN5329QI Soldering Guidelines for more details and recommendations. Figure 10. Recommended Footprint for PCB (Top View) Note: Grey area highlights exposed metal that is not to be mechanically or electrically connected to the PCB. 18 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Recommended PCB Footprint Figure 11. EN5329 PCB Footprint (Top View) The solder stencil aperture for the thermal pads (shown in blue) is based on Altera's manufacturing recommendations 19 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Package Mechanical Figure 12. EN5329QI Package Dimensions (Bottom View) Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html 20 08326 June 3, 2016 www.altera.com/enpirion Rev E EN5329QI Revision History Rev Date A B C March 2013 Dec 2013 July 2015 D Oct 2015 E June 2016 Change(s) Introductory production datasheet Formatting changes Updated pre-bias voltage to 1.5V Updated current limit in Electrical Characteristics Table Updated soft-start calculation Modified ENABLE description Included minimum footprint design parameters Modified front page to show applications schematic Formatting changes Contact Information Altera Corporation 101 Innovation Drive San Jose, CA 95134 Phone: 408-544-7000 www.altera.com (c) 2013 Altera Corporation--Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. 21 08326 June 3, 2016 www.altera.com/enpirion Rev E