LM148/LM248/LM348
Quad 741 Op Amps
LM149
Wide Band Decompensated (A
V (MIN)
=5)
General Description
The LM148 series is a true quad 741. It consists of four
independent, high gain, internally compensated, low power
operational amplifiers which have been designed to provide
functional characteristics identical to those of the familiar
741 operational amplifier. In addition the total supply current
for all four amplifiers is comparable to the supply current of a
single 741 type op amp. Other features include input offset
currents and input bias current which are much less than
those of a standard 741. Also, excellent isolation between
amplifiers has been achieved by independently biasing each
amplifier and using layout techniques which minimize
thermal coupling. The LM149 series has the same features
as the LM148 plus a gain bandwidth product of 4 MHz at a
gain of 5 or greater.
The LM148 can be used anywhere multiple 741 or 1558 type
amplifiers are being used and in applications where amplifier
matching or high packing density is required. For lower
power refer to LF444.
Features
n741 op amp operating characteristics
nClass AB output stageno crossover distortion
nPin compatible with the LM124
nOverload protection for inputs and outputs
nLow supply current drain: 0.6 mA/Amplifier
nLow input offset voltage: 1 mV
nLow input offset current: 4 nA
nLow input bias current 30 nA
nHigh degree of isolation between amplifiers: 120 dB
nGain bandwidth product
nLM148 (unity gain): 1.0 MHz
nLM149 (A
V
5): 4 MHz
Schematic Diagram
DS007786-1
* 1 pF in the LM149
December 2000
LM148/LM149 Series Quad 741 Op Amp
© 2001 National Semiconductor Corporation DS007786 www.national.com
Absolute Maximum Ratings (Note 4)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
LM148/LM149 LM248 LM348
Supply Voltage ±22V ±18V ±18V
Differential Input Voltage ±44V ±36V ±36V
Output Short Circuit Duration (Note 1) Continuous Continuous Continuous
Power Dissipation (P
d
at 25˚C) and
Thermal Resistance (θ
jA
), (Note 2)
Molded DIP (N) P
d
750 mW
θ
jA
100˚C/W
Cavity DIP (J) P
d
1100 mW 800 mW 700 mW
θ
JA
110˚C/W 110˚C/W 110˚C/W
Maximum Junction Temperature (T
jMAX
) 150˚C 110˚C 100˚C
Operating Temperature Range −55˚C T
A
+125˚C −25˚C T
A
+85˚C 0˚C T
A
+70˚C
Storage Temperature Range −65˚C to +150˚C −65˚C to +150˚C −65˚C to +150˚C
Lead Temperature (Soldering, 10 sec.) Ceramic 300˚C 300˚C 300˚C
Lead Temperature (Soldering, 10 sec.) Plastic 260˚C
Soldering Information
Dual-In-Line Package
Soldering (10 seconds) 260˚C 260˚C 260˚C
Small Outline Package
Vapor Phase (60 seconds) 215˚C 215˚C 215˚C
Infrared (15 seconds) 220˚C 220˚C 220˚C
See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount
devices.
ESD tolerance (Note 5) 500V 500V 500V
Electrical Characteristics
(Note 3)
Parameter Conditions LM148/LM149 LM248 LM348 Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage T
A
= 25˚C, R
S
10 k1.0 5.0 1.0 6.0 1.0 6.0 mV
Input Offset Current T
A
= 25˚C 4 25 4 50 4 50 nA
Input Bias Current T
A
= 25˚C 30 100 30 200 30 200 nA
Input Resistance T
A
= 25˚C 0.8 2.5 0.8 2.5 0.8 2.5 M
Supply Current All Amplifiers T
A
= 25˚C, V
S
=±15V 2.4 3.6 2.4 4.5 2.4 4.5 mA
Large Signal Voltage Gain T
A
= 25˚C, V
S
=±15V 50 160 25 160 25 160 V/mV
V
OUT
=±10V, R
L
2k
Amplifier to Amplifier T
A
= 25˚C, f = 1 Hz to 20 kHz
Coupling (Input Referred) See Crosstalk −120 −120 −120 dB
Test Circuit
Small Signal Bandwidth LM148 Series 1.0 1.0 1.0 MHz
T
A
= 25˚C
LM149 Series 4.0 4.0 4.0 MHz
Phase Margin LM148 Series (A
V
= 1) 60 60 60 degrees
T
A
= 25˚C
LM149 Series (A
V
= 5) 60 60 60 degrees
Slew Rate LM148 Series (A
V
= 1) 0.5 0.5 0.5 V/µs
T
A
= 25˚C
LM149 Series (A
V
= 5) 2.0 2.0 2.0 V/µs
Output Short Circuit Current T
A
= 25˚C 25 25 25 mA
Input Offset Voltage R
S
10 k6.0 7.5 7.5 mV
Input Offset Current 75 125 100 nA
LM148/LM149/LM248/LM348
www.national.com 2
Electrical Characteristics (Continued)
(Note 3)
Parameter Conditions LM148/LM149 LM248 LM348 Units
Min Typ Max Min Typ Max Min Typ Max
Input Bias Current 325 500 400 nA
Large Signal Voltage Gain V
S
=±15V, V
OUT
=±10V, 25 15 15 V/mV
R
L
>2k
Output Voltage Swing V
S
=±15V, R
L
=10k±
12 ±13 ±12 ±13 ±12 ±13 V
R
L
=2k±
10 ±12 ±10 ±12 ±10 ±12 V
Input Voltage Range V
S
=±15V ±12 ±12 ±12 V
Common-Mode Rejection R
S
10 k70 90 70 90 70 90 dB
Ratio
Supply Voltage Rejection R
S
10 k,±5V V
S
±15V 77 96 77 96 77 96 dB
Note 1: Any of the amplifier outputs can be shorted to ground indefinitely; however, more than one should not be simultaneously shorted as the maximum junction
temperature will be exceeded.
Note 2: The maximum power dissipation for these devices must be derated at elevated temperatures and is dicated by TjMAX,θjA, and the ambient temperature,
TA. The maximum available power dissipation at any temperature is Pd=(T
jMAX −T
A
)/θjA or the 25˚C PdMAX, whichever is less.
Note 3: These specifications apply for VS=±15V and over the absolute maximum operating temperature range (TLTATH) unless otherwise noted.
Note 4: Refer to RETS 148X for LM148 military specifications and refer to RETS 149X for LM149 military specifications.
Note 5: Human body model, 1.5 kin series with 100 pF.
Cross Talk Test Circuit
Application Hints
The LM148 series are quad low power 741 op amps. In the
proliferation of quad op amps, these are the first to offer the
convenience of familiar, easy to use operating
characteristics of the 741 op amp. In those applications
where 741 op amps have been employed, the LM148 series
op amps can be employed directly with no change in circuit
performance.
The LM149 series has the same characteristics as the
LM148 except it has been decompensated to provide a
wider bandwidth. As a result the part requires a minimum
gain of 5.
DS007786-6 DS007786-7
DS007786-43
VS=±15V
LM148/LM149/LM248/LM348
www.national.com3
Typical Performance Characteristics
Supply Current
DS007786-23
Input Bias Current
DS007786-24
Voltage Swing
DS007786-25
Positive Current Limit
DS007786-26
Negative Current Limit
DS007786-27
Output Impedance
DS007786-28
Common-Mode Rejection
Ratio
DS007786-29
Open Loop Frequency
Response
DS007786-30
Bode Plot LM148
DS007786-31
LM148/LM149/LM248/LM348
www.national.com 4
Typical Performance Characteristics (Continued)
Bode Plot LM149
DS007786-32
Large Signal Pulse
Response (LM148)
DS007786-33
Large Signal Pulse
Response (LM149)
DS007786-34
Small Signal Pulse
Response (LM148)
DS007786-35
Small Signal Pulse
Response (LM149)
DS007786-36
Undistorted Output
Voltage Swing
DS007786-37
Gain Bandwidth
DS007786-38
Slew Rate
DS007786-39
Inverting Large Signal Pulse
Response (LM149)
DS007786-40
LM148/LM149/LM248/LM348
www.national.com5
Typical Performance Characteristics (Continued)
Application Hints
The LM148 series are quad low power 741 op amps. In the
proliferation of quad op amps, these are the first to offer the
convenience of familiar, easy to use operating
characteristics of the 741 op amp. In those applications
where 741 op amps have been employed, the LM148 series
op amps can be employed directly with no change in circuit
performance.
The LM149 series has the same characteristics as the
LM148 except it has been decompensated to provide a
wider bandwidth. As a result the part requires a minimum
gain of 5.
The package pin-outs are such that the inverting input of
each amplifier is adjacent to its output. In addition, the
amplifier outputs are located in the corners of the package
which simplifies PC board layout and minimizes package
related capacitive coupling between amplifiers.
The input characteristics of these amplifiers allow differential
input voltages which can exceed the supply voltages. In
addition, if either of the input voltages is within the operating
common-mode range, the phase of the output remains
correct. If the negative limit of the operating common-mode
range is exceeded at both inputs, the output voltage will be
positive. For input voltages which greatly exceed the
maximum supply voltages, either differentially or
common-mode, resistors should be placed in series with the
inputs to limit the current.
Like the LM741, these amplifiers can easily drive a 100 pF
capacitive load throughout the entire dynamic output voltage
and current range. However, if very large capacitive loads
must be driven by a non-inverting unity gain amplifier, a
resistor should be placed between the output (and feedback
connection) and the capacitance to reduce the phase shift
resulting from the capacitive loading.
The output current of each amplifier in the package is limited.
Short circuits from an output to either ground or the power
supplies will not destroy the unit. However, if multiple output
shorts occur simultaneously, the time duration should be
short to prevent the unit from being destroyed as a result of
excessive power dissipation in the IC chip.
Inverting Large Signal Pulse
Response (LM148)
DS007786-41
Input Noise Voltage and
Noise Current
DS007786-42
Positive Common-Mode
Input Voltage Limit
DS007786-43
Negative Common-Mode Input
Voltage Limit
DS007786-5
LM148/LM149/LM248/LM348
www.national.com 6
Application Hints (Continued)
As with most amplifiers, care should be taken lead dress,
component placement and supply decoupling in order to
ensure stability. For example, resistors from the output to an
input should be placed with the body close to the input to
minimize “pickup” and maximize the frequency of the
feedback pole which capacitance from the input to ground
creates.
A feedback pole is created when the feedback around any
amplifier is resistive. The parallel resistance and capacitance
from the input of the device (usually the inverting input) toAC
ground set the frequency of the pole. In many instances the
frequency of this pole is much greater than the expected 3
dB frequency of the closed loop gain and consequently there
is negligible effect on stability margin. However, if the
feedback pole is less than approximately six times the
expected 3 dB frequency a lead capacitor should be placed
from the output to the input of the op amp. The value of the
added capacitor should be such that the RC time constant of
this capacitor and the resistance it parallels is greater than or
equal to the original feedback pole time constant.
Typical ApplicationsLM148
One Decade Low Distortion Sinewave Generator
DS007786-8
fMAX = 5 kHz, THD 0.03%
R1 = 100k pot. C1 = 0.0047 µF, C2 = 0.01 µF, C3 = 0.1 µF, R2 = R6 = R7 = 1M,
R3 = 5.1k, R4 = 12, R5 = 240, Q = NS5102, D1 = 1N914, D2 = 3.6V avalanche
diode (ex. LM103), VS=±15V
A simpler version with some distortion degradation at high frequencies can be made by using A1 as a simple inverting amplifier, and by putting back to back
zeners in the feedback loop of A3.
LM148/LM149/LM248/LM348
www.national.com7
Typical ApplicationsLM148 (Continued)
Low Cost Instrumentation Amplifier
DS007786-9
VS=±15V
R = R2, trim R2 to boost CMRR
Low Drift Peak Detector with Bias Current Compensation
DS007786-10
Adjust R for minimum drift
D3 low leakage diode
D1 added to improve speed
VS=±15V
LM148/LM149/LM248/LM348
www.national.com 8
Typical ApplicationsLM148 (Continued)
Universal State-Variable Filter
DS007786-11
Tune Q through R0,
For predictable results: fOQ4x10
4
Use Band Pass output to tune for Q
LM148/LM149/LM248/LM348
www.national.com9
Typical ApplicationsLM148 (Continued)
A 1 kHz 4 Pole Butterworth
DS007786-12
Use general equations, and tune each section separately
Q1stSECTION = 0.541, Q2ndSECTION = 1.306
The response should have 0 dB peaking
A 3 Amplifier Bi-Quad Notch Filter
DS007786-13
Ex: fNOTCH = 3 kHz, Q = 5, R1 = 270k, R2 = R3 = 20k, R4 = 27k, R5 = 20k, R6 = R8 = 10k, R7 = 100k, C1 = C2 = 0.001 µF
Better noise performance than the state-space approach.
LM148/LM149/LM248/LM348
www.national.com 10
Typical ApplicationsLM148 (Continued)
A 4th Order 1 kHz Elliptic Filter (4 Poles, 4 Zeros)
DS007786-14
R1C1 = R2C2 = t
R'1C'1 = R'2C'2 = t'
fC= 1 kHz, fS= 2 kHz, fp= 0.543, fZ= 2.14, Q = 0.841, f' P= 0.987, f' Z= 4.92, Q' = 4.403, normalized to ripple BW
Use the BP outputs to tune Q, Q', tune the 2 sections separately
R1 = R2 = 92.6k, R3 = R4 = R5 = 100k, R6 = 10k, R0 = 107.8k, RL= 100k, RH= 155.1k,
R'1 = R'2 = 50.9k, R'4 = R'5 = 100k, R'6 = 10k, R'0 = 5.78k, R'L= 100k, R'H= 248.12k, R'f = 100k. All capacitors are 0.001 µF.
Lowpass Response
DS007786-15
LM148/LM149/LM248/LM348
www.national.com11
Typical ApplicationsLM149
Minimum Gain to Insure LM149 Stability
DS007786-16
The LM149 as a Unity Gain Inverter
DS007786-17
Non-inverting-Integrator Bandpass Filter
DS007786-18
For stability purposes: R7 = R6/4, 10R6 = R5, CC= 10C
fO(MAX),Q
MAX = 20 kHz, 10
Better Q sensitivity with respect to open loop gain variations than the state variable filter.
R7, CCadded for compensation
LM148/LM149/LM248/LM348
www.national.com 12
Typical ApplicationsLM149 (Continued)
Active Tone Control with Full Output Swing (No Slew Limiting at 20 kHz)
DS007786-19
VS=±15V, VOUT(MAX) = 9.1 VRMS,
fMAX = 20 kHz, THD 1%
Duplicate the above circuit for stereo
Max Bass Gain .(R1 + R2)/R1
Max Treble Gain .(R1 + 2R7)/R5
as shown: fL.32 Hz, fLB .320 Hz
fH.11 kHz, fHB .1.1 Hz
LM148/LM149/LM248/LM348
www.national.com13
Typical ApplicationsLM149 (Continued)
Triangular Squarewave Generator
DS007786-20
Use LM125 for ±15V supply
The circuit can be used as a low frequency V/F for process control.
Q1, Q3: KE4393, Q2, Q4: P1087E, D1–D4 = 1N914
LM148/LM149/LM248/LM348
www.national.com 14
Typical Simulation
LM148, LM149, LM741 Macromodel for Computer Simulation
DS007786-21
For more details, see IEEE Journal of Solid-State Circuits, Vol. SC-9, No. 6, December 1974
Note 6: o1 = 112IS=8x10
−16
Note 7: o2 = 144*C2 = 6 pF for LM149
DS007786-22
LM148/LM149/LM248/LM348
www.national.com15
Connection Diagram
DS007786-2
Top View
Order Number LM148J, LM148J/883, LM149J/883, LM248J, LM348M, or LM348N
See NS Package Number J14A, M14A or N14A
LM148J is available per JM38510/11001
LM148/LM149/LM248/LM348
www.national.com 16
Physical Dimensions inches (millimeters) unless otherwise noted
Ceramic Dual-In-Line Package (J)
Order Number LM148J, LM148J/883, LM149J/883, LM248J
NS Package Number J14A
S.O. Package (M)
Order Number LM348M or LM348MX
NS Package Number M14A
LM148/LM149/LM248/LM348
www.national.com17
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
Molded Dual-In-Line Package (N)
Order Number LM348N
NS Package Number N14A
LM148/LM149 Series Quad 741 Op Amp
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.