LP2987,LP2988 LP2987/LP2988 Micropower, 200 mA Ultra Low-Dropout Voltage Regulator with Programmable Power-On Reset Delay; Low Noise Version Available (LP2988) Literature Number: SNVS004I LP2987/LP2988 Micropower, 200 mA Ultra Low-Dropout Voltage Regulator with Programmable Power-On Reset Delay; Low Noise Version Available (LP2988) General Description Features The LP2987/8 are fixed-output 200 mA precision LDO voltage regulators with power-ON reset delay which can be implemented using a single external capacitor. n n n n n n n n n n n n The LP2988 is specifically designed for noise-critical applications. A single external capacitor connected to the Bypass pin reduces regulator output noise. Using an optimized VIPTM (Vertically Integrated PNP) process, these regulators deliver superior performance: Dropout Voltage: 180 mV @ 200 mA load, and 1 mV @ 1 mA load (typical). Ground Pin Current: 1 mA @ 200 mA load, and 200 A @ 10 mA load (typical). Sleep Mode: The LP2987/8 draws less than 2 A quiescent current when shutdown pin is held low. Error Flag/Reset: The error flag goes low when the output drops approximately 5% below nominal. This pin also provides a power-ON reset signal if a capacitor is connected to the DELAY pin. Precision Output: Standard product versions of the LP2987 and LP2988 are available with output voltages of 5.0V, 3.8V, 3.3V, 3.2V, 3.0V, or 2.8V, with guaranteed accuracy of 0.5% ("A" grade) and 1% (standard grade) at room temperature. Ultra low dropout voltage Power-ON reset delay requires only one component Bypass pin for reduced output noise (LP2988) Guaranteed continuous output current 200 mA Guaranteed peak output current > 250 mA SO-8 and mini SO-8 surface mount packages < 2 A quiescent current when shutdown Low ground pin current at all loads 0.5% output voltage accuracy ("A" grade) Wide supply voltage range (16V max) Overtemperature/overcurrent protection -40C to +125C junction temperature range Applications n Cellular Phone n Palmtop/Laptop Computer n Camcorder, Personal Stereo, Camera Block Diagrams 10001701 10001702 VIPTM is a trademark of National Semiconductor Corporation. (c) 2005 National Semiconductor Corporation DS100017 www.national.com LP2987/LP2988 Micropower, 200 mA Ultra Low-Dropout Voltage Regulator with Programmable Power-On Reset Delay March 2005 LP2987/LP2988 Connection Diagram (LP2987) Surface Mount Packages: 8-Lead LLP Surface Mount Package 10001703 Top View SO-8/Mini SO-8 Package See NS Package Drawing Number M08A/MUA08A For ordering information, refer to Table 1in this document. 10001757 Top View See NS Package Drawing Number LDC08A Ordering Information (LP2987) TABLE 1. Package Marking and Ordering Information Output Voltage Grade Order Information Package Marking Supplied as: 5 A LP2987AIMMX-5.0 L44A 3500 Units on Tape and Reel 5 A LP2987AIMM-5.0 L44A 1000 Units on Tape and Reel 5 STD LP2987IMMX-5.0 L44B 3500 Units on Tape and Reel 5 STD LP2987IMM-5.0 L44B 1000 Units on Tape and Reel 3.8 A LP2987AIMMX-3.8 L96A 3500 Units on Tape and Reel 3.8 A LP2987AIMM-3.8 L96A 1000 Units on Tape and Reel 3.8 STD LP2987IMMX-3.8 L96B 3500 Units on Tape and Reel 3.8 STD LP2987IMM-3.8 L96B 1000 Units on Tape and Reel 3.3 A LP2987AIMMX-3.3 L43A 3500 Units on Tape and Reel 3.3 A LP2987AIMM-3.3 L43A 1000 Units on Tape and Reel 3.3 STD LP2987IMMX-3.3 L43B 3500 Units on Tape and Reel 3.3 STD LP2987IMM-3.3 L43B 1000 Units on Tape and Reel 3.2 A LP2987AIMMX-3.2 L66A 3500 Units on Tape and Reel 3.2 A LP2987AIMM-3.2 L66A 1000 Units on Tape and Reel 3.2 STD LP2987IMMX-3.2 L66B 3500 Units on Tape and Reel 3.2 STD LP2987IMM-3.2 L66B 1000 Units on Tape and Reel 3.0 A LP2987AIMMX-3.0 L42A 3500 Units on Tape and Reel www.national.com 2 (Continued) TABLE 1. Package Marking and Ordering Information (Continued) Output Voltage Grade Order Information Package Marking Supplied as: 3.0 A LP2987AIMM-3.0 L42A 1000 Units on Tape and Reel 3.0 STD LP2987IMMX-3.0 L42B 3500 Units on Tape and Reel 3.0 STD LP2987IMM-3.0 L42B 1000 Units on Tape and Reel 2.8 A LP2987AIMMX-2.8 L89A 3500 Units on Tape and Reel 2.8 A LP2987AIMM-2.8 L89A 1000 Units on Tape and Reel 2.8 STD LP2987IMMX-2.8 L89B 3500 Units on Tape and Reel 2.8 STD LP2987IMM-2.8 L89B 1000 Units on Tape and Reel 5 A LP2987AIMX-5.0 2987AIM5.0 2500 Units on Tape and Reel 5 A LP2987AIM-5.0 2987AIM5.0 Shipped in Anti-Static Rails 5 STD LP2987IMX-5.0 2987IM5.0 2500 Units on Tape and Reel 5 STD LP2987IM-5.0 2987IM5.0 Shipped in Anti-Static Rails 3.8 A LP2987AIMX-3.8 2987AIM3.8 2500 Units on Tape and Reel 3.8 A LP2987AIM-3.8 2987AIM3.8 Shipped in Anti-Static Rails 3.8 STD LP2987IMX-3.8 2987IM3.8 2500 Units on Tape and Reel 3.8 STD LP2987IM-3.8 2987IM3.8 Shipped in Anti-Static Rails 3.3 A LP2987AIMX-3.3 2987AIM3.3 2500 Units on Tape and Reel 3.3 A LP2987AIM-3.3 2987AIM3.3 Shipped in Anti-Static Rails 3.3 STD LP2987IMX-3.3 2987IM3.3 2500 Units on Tape and Reel 3.3 STD LP2987IM-3.3 2987IM3.3 Shipped in Anti-Static Rails 3.2 A LP2987AIMX-3.2 2987AIM3.2 2500 Units on Tape and Reel 3.2 A LP2987AIM-3.2 2987AIM3.2 Shipped in Anti-Static Rails 3.2 STD LP2987IMX-3.2 2987IM3.2 2500 Units on Tape and Reel 3.2 STD LP2987AIM-3.2 2987IM3.2 Shipped in Anti-Static Rails 3.0 A LP2987IMX-3.0 2987AIM3.0 2500 Units on Tape and Reel 3.0 A LP2987AIM-3.0 2987AIM3.0 Shipped in Anti-Static Rails 3 www.national.com LP2987/LP2988 Ordering Information (LP2987) LP2987/LP2988 Ordering Information (LP2987) (Continued) TABLE 1. Package Marking and Ordering Information (Continued) Output Voltage Grade Order Information Package Marking Supplied as: 3.0 STD LP2987IMX-3.0 2987IM3.0 2500 Units on Tape and Reel 3.0 STD LP2987IM-3.0 2987IM3.0 Shipped in Anti-Static Rails 2.8 A LP2987AIMX-2.8 2987AIM2.8 2500 Units on Tape and Reel 2.8 A LP2987AIM-2.8 2987AIM2.8 Shipped in Anti-Static Rails 2.8 STD LP2987IMX-2.8 2987IM2.8 2500 Units on Tape and Reel 2.8 STD LP2987AIM-2.8 2987AIM2.8 Shipped in Anti-Static Rails 5 A LP2987AILD-5 L009A 1000 Units on Tape and Reel 5 A LP2987AILDX-5 L009A 4500 Units on Tape and Reel 5 STD LP2987ILD-5 L009AB 1000 Units on Tape and Reel 5 STD LP2987ILDX-5 L009AB 4500 Units on Tape and Reel 3.3 A LP2987AILD-3.3 L008A 1000 Units on Tape and Reel 3.3 A LP2987AILDX-3.3 L008A 4500 Units on Tape and Reel 3.3 STD LP2987ILD-3.3 L008AB 1000 Units on Tape and Reel 3.3 STD LP2987ILDX-3.3 L008AB 4500 Units on Tape and Reel 3.0 A LP2987AILD-3.0 L007A 1000 Units on Tape and Reel 3.0 A LP2987AILDX-3.0 L007A 4500 Units on Tape and Reel 3.0 STD LP2987ILD-3.0 L007AB 1000 Units on Tape and Reel 3.0 STD LP2987ILDX-3.0 L007AB 4500 Units on Tape and Reel 8-Lead LLP www.national.com 4 LP2987/LP2988 Connection Diagram (LP2988) Surface Mount Packages: 8-Lead LLP Surface Mount Package 10001704 Top View SO-8/Mini SO-8 Package See NS Package Drawing Number M08A/MUA08A For ordering information, refer to Table 1in this document. 10001758 Top View See NS Package Drawing Number LDC08A Ordering Information (LP2988) TABLE 2. Package Marking and Ordering Information Output Voltage Grade Order Information Package Marking Supplied as: 5.7 A LP2988AIMMX-5.7 LF2A 3500 Units on Tape and Reel 5.7 A LP2988AIMM-5.7 LF2A 1000 Units on Tape and Reel 5.7 STD LP2988IMMX-5.7 LF2B 3500 Units on Tape and Reel 5.7 STD LP2988IMM-5.7 LF2B 1000 Units on Tape and Reel 5.0 A LP2988AIMMX-5.0 L51A 3500 Units on Tape and Reel 5.0 A LP2988AIMM-5.0 L51A 1000 Units on Tape and Reel 5.0 STD LP2988IMMX-5.0 L51B 3500 Units on Tape and Reel 5.0 STD LP2988IMM-5.0 L51B 1000 Units on Tape and Reel 3.8 A LP2988AIMMX-3.8 L0AA 3500 Units on Tape and Reel 3.8 A LP2988AIMM-3.8 L0AA 1000 Units on Tape and Reel 3.8 STD LP2988IMMX-3.8 L0AB 3500 Units on Tape and Reel 3.8 STD LP2988IMM-3.8 L0AB 1000 Units on Tape and Reel 3.3 A LP2988AIMMX-3.3 L50A 3500 Units on Tape and Reel 3.3 A LP2988AIMM-3.3 L50A 1000 Units on Tape and Reel 3.3 STD LP2988IMMX-3.3 L50B 3500 Units on Tape and Reel 3.3 STD LP2988IMM-3.3 L50B 1000 Units on Tape and Reel 3.2 A LP2988AIMMX-3.2 L67A 3500 Units on Tape and Reel 3.2 A LP2988AIMM-3.2 L67A 1000 Units on Tape and Reel 5 www.national.com LP2987/LP2988 Ordering Information (LP2988) (Continued) TABLE 2. Package Marking and Ordering Information (Continued) Output Voltage Grade Order Information Package Marking Supplied as: 3.2 STD LP2988IMMX-3.2 L67B 3500 Units on Tape and Reel 3.2 STD LP2988IMM-3.2 L67B 1000 Units on Tape and Reel 3.0 A LP2988AIMMX-3.0 L49A 3500 Units on Tape and Reel 3.0 A LP2988AIMM-3.0 L49A 1000 Units on Tape and Reel 3.0 STD LP2988IMMX-3.0 L49B 3500 Units on Tape and Reel 3.0 STD LP2988IMM-3.0 L49B 1000 Units on Tape and Reel 2.8 A LP2988AIMMX-2.8 L0IA 3500 Units on Tape and Reel 2.8 A LP2988AIMM-2.8 L0IA 1000 Units on Tape and Reel 2.8 STD LP2988IMMX-2.8 L0IB 3500 Units on Tape and Reel 2.8 STD LP2988IMM-2.8 L0IB 1000 Units on Tape and Reel 2.7 A LP2988AIMMX-2.7 LCVA 3500 Units on Tape and Reel 2.7 A LP2988AIMM-2.7 LCVA 1000 Units on Tape and Reel 2.7 STD LP2988IMMX-2.7 LCVB 3500 Units on Tape and Reel 2.7 STD LP2988IMM-2.7 LCVB 1000 Units on Tape and Reel 2.5 A LP2988AIMMX-2.5 L99A 3500 Units on Tape and Reel 2.5 A LP2988AIMM-2.5 L99A 1000 Units on Tape and Reel 2.5 STD LP2988IMMX-2.5 L99B 3500 Units on Tape and Reel 2.5 STD LP2988IMM-2.5 L99B 1000 Units on Tape and Reel 5.0 A LP2988AIMX-5.0 2988AIM5.0 2500 Units on Tape and Reel 5.0 A LP2988AIM-5.0 2988AIM5.0 Shipped in Anti-Static Rails 5.0 STD LP2988IMX-5.0 2988IM5.0 2500 Units on Tape and Reel 5.0 STD LP2988IM-5.0 2988IM5.0 Shipped in Anti-Static Rails 3.8 A LP2988AIMX-3.8 2988AIM3.8 2500 Units on Tape and Reel 3.8 A LP2988AIM-3.8 2988AIM3.8 Shipped in Anti-Static Rails 3.8 STD LP2988IMX-3.8 2988IM3.8 2500 Units on Tape and Reel www.national.com 6 (Continued) TABLE 2. Package Marking and Ordering Information (Continued) Output Voltage Grade Order Information Package Marking Supplied as: 3.8 STD LP2988IM-3.8 2988IM3.8 Shipped in Anti-Static Rails 3.3 A LP2988AIMX-3.3 2988AIM3.3 2500 Units on Tape and Reel 3.3 A LP2988AIM-3.3 2988AIM3.3 Shipped in Anti-Static Rails 3.3 STD LP2988IMX-3.3 2988IM3.3 2.5k Units on Tape and Reel 3.3 STD LP2988IM-3.3 2988IM3.3 Shipped in Anti-Static Rails 3.2 A LP2988AIMX-3.2 2988AIM3.2 2500 Units on Tape and Reel 3.2 A LP2988AIM-3.2 2988AIM3.2 Shipped in Anti-Static Rails 3.2 STD LP2988IMX-3.2 2988IM3.2 2500 Units on Tape and Reel 3.2 STD LP2988IM-3.2 2988IM3.2 Shipped in Anti-Static Rails 3.0 A LP2988AIMX-3.0 2988AIM3.0 2500 Units on Tape and Reel 3.0 A LP2988AIM-3.0 2988AIM3.0 Shipped in Anti-Static Rails 3.0 STD LP2988IMX-3.0 2988IM3.0 2500 Units on Tape and Reel 3.0 STD LP2988IM-3.0 2988IM3.0 Shipped in Anti-Static Rails 2.8 A LP2988AIMX-2.8 2988AIM2.8 2500 Units on Tape and Reel 2.8 A LP2988AIM-2.8 2988AIM2.8 Shipped in Anti-Static Rails 2.8 STD LP2988IMX-2.8 2988IM2.8 2500 Units on Tape and Reel 2.8 STD LP2988IM-2.8 2988IM2.8 Shipped in Anti-Static Rails 2.7 A LP2988AIMX-2.7 2988AIM2.7 2500 Units on Tape and Reel 2.7 A LP2988AIM-2.7 2988AIM2.7 Shipped in Anti-Static Rails 2.7 STD LP2988IMX-2.7 2988IM2.7 2500 Units on Tape and Reel 2.7 STD LP2988IM-2.7 2988IM2.7 Shipped in Anti-Static Rails 2.5 A LP2988AIMX-2.5 2988AIM2.5 2500 Units on Tape and Reel 2.5 A LP2988AIM-2.5 2988AIM2.5 Shipped in Anti-Static Rails 2.5 STD LP2988IMX-2.5 2988IM2.5 2500 Units on Tape and Reel 2.5 STD LP2988IM-2.5 2988IM2.5 Shipped in Anti-Static Rails 7 www.national.com LP2987/LP2988 Ordering Information (LP2988) LP2987/LP2988 Ordering Information (LP2988) (Continued) TABLE 2. Package Marking and Ordering Information (Continued) Output Voltage Grade Order Information Package Marking Supplied as: 5 A LP2988AILD-5 L01DA 1000 Units on Tape and Reel 5 A LP2988AILDX-5 L01DA 4500 Units on Tape and Reel 5 STD LP2988ILD-5 L01DAB 1000 Units on Tape and Reel 5 STD LP2988ILDX-5 L01DAB 4500 Units on Tape and Reel 3.3 A LP2988AILD-3.3 L01CA 1000 Units on Tape and Reel 3.3 A LP2988AILDX-3.3 L01CA 4500 Units on Tape and Reel 3.3 STD LP2988ILD-3.3 L01CAB 1000 Units on Tape and Reel 3.3 STD LP2988ILDX-3.3 L01CAB 4500 Units on Tape and Reel 3.0 A LP2988AILD-3.0 L01BA 1000 Units on Tape and Reel 3.0 A LP2988AILDX-3.0 L01BA 4500 Units on Tape and Reel 3.0 STD LP2988ILD-3.0 L01BAB 1000 Units on Tape and Reel 3.0 STD LP2988ILDX-3.0 L01BAB 4500 Units on Tape and Reel 2.5 A LP2988AILD-2.5 L01AA 1000 Units on Tape and Reel 2.5 A LP2988AILDX-2.5 L01AA 4500 Units on Tape and Reel 2.5 STD LP2988ILD-2.5 L01AAB 1000 Units on Tape and Reel 2.5 STD LP2988ILDX-2.5 L01AAB 4500 Units on Tape and Reel 8-Lead LLP www.national.com 8 Input Supply Voltage (Survival) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range -65C to +150C Operating Junction Temperature Range -40C to +125C -0.3V to +16V Input Supply Voltage (Operating) 2.1V to +16V Shutdown Pin -0.3V to +16V Sense Pin Lead Temperature (Soldering, 5 seconds) 260C ESD Rating (Note 2) -0.3V to +16V IOUT (Survival) 2 kV Power Dissipation (Note 3) -0.3V to +6V Output Voltage (Survival) (Note 4) Short Circuit Protected Input-Output Voltage (Survival) (Note 5) Internally Limited -0.3V to +16V Electrical Characteristics Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 4.7 F, CIN = 2.2 F, VS/D = 2V. Symbol VO VIN-VO Parameter Output Voltage Tolerance Conditions Typical 0.1 mA < IL < 200 mA Output Voltage Line Regulation VO(NOM) + 1V VIN 16V Dropout Voltage (Note 7) IL = 100 A Ground Pin Current Max Min Max -0.5 0.5 -1.0 1.0 -0.8 0.8 -1.6 1.6 -1.8 1.8 -2.8 2.8 1 90 IL = 200 mA 180 IL = 100 A 100 IL = 75 mA 500 IL = 200 mA LM2987/8I-X.X (Note 6) Min 0.007 IL = 75 mA IGND LM2987/8AI-X.X (Note 6) 1 Units %VNOM 0.014 0.014 0.032 0.032 2.0 2.0 3.5 3.5 120 120 170 170 230 230 350 350 120 120 150 150 800 800 1400 1400 2.1 2.1 3.7 3.7 %/V mV A mA VS/D < 0.3V 0.05 IO(PK) Peak Output Current VOUT VO(NOM) - 5% 400 IO(MAX) Short Circuit Current RL = 0 (Steady State) (Note 10) 400 en LP2987 Output Noise Voltage (RMS) BW = 300 Hz to 50 kHz, VOUT = 3.3V COUT = 10 F 100 LP2988 Output Noise Voltage (RMS) BW = 300 Hz to 50 kHz, VOUT = 3.3V COUT = 10 F CBYPASS = .01 F 20 Ripple Rejection f = 1 kHz, COUT = 10 F CBYP = 0 (LP2988) 65 dB 20 ppm/C Output Voltage Temperature Coefficient 1.5 250 1.5 A 250 mA V(RMS) (Note 9) 9 www.national.com LP2987/LP2988 Absolute Maximum Ratings (Note 1) LP2987/LP2988 Electrical Characteristics (Continued) Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 4.7 F, CIN = 2.2 F, VS/D = 2V. Symbol IDELAY Parameter Conditions Typical Delay Pin Current Source 2.2 LM2987/8AI-X.X (Note 6) LM2987/8I-X.X (Note 6) Min Max Min Max 1.6 2.8 1.6 2.8 1.4 3.0 1.4 3.0 Units A SHUTDOWN INPUT VS/D IS/D S/D Input Voltage (Note 8) VH = O/P ON 1.4 VL = O/P OFF 0.55 1.6 0.18 1.6 0.18 S/D Input Current VS/D = 0 0 -1 -1 VS/D = 5V 5 15 15 1 1 2 2 220 220 350 350 V A ERROR COMPARATOR IOH VOL Output "HIGH" Leakage Output "LOW" Voltage VTHR (MAX) Upper Threshold Voltage VTHR (MIN) Lower Threshold Voltage HYST Hysteresis VOH = 16V 0.01 VIN = VO(NOM) - 0.5V, IO(COMP) = 300 A 150 -4.6 -6.6 -5.5 -3.5 -5.5 -3.5 -7.7 -2.5 -7.7 -2.5 -8.9 -4.9 -8.9 -4.9 -13.0 -3.3 -13.0 -3.3 A mV %VOUT 2.0 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: The ESD rating of the Bypass pin is 500V (LP2988 only). The ESD rating of the VIN pin is 1kV and the Delay pin is ESD rated at 1.5kV. Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, J-A, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: The value of J-A for the SO-8 (M) package is 160C/W, and the mini SO-8 (MM) package is 200C/W. The value J-A for the LLP (LD) package is specifically dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the LLP package, refer to Application Note AN-1187. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LM2987/8 output must be diode-clamped to ground. Note 5: The output PNP structure contains a diode between the VIN and VOUT terminals that is normally reverse-biased. Forcing the output above the input will turn on this diode and may induce a latch-up mode which can damage the part (see Application Hints). Note 6: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential. Note 8: To prevent mis-operation, the Shutdown input must be driven by a signal that swings above VH and below VL with a slew rate not less than 40 mV/s (see Application Hints). Note 9: Temperature coefficient is defined as the maximum (worst-case) change divided by the total temperature range. Note 10: See Typical Performance Characteristics curves. www.national.com 10 VOUT vs Temperature Dropout Voltage vs Temperature 10001717 10001718 Dropout Voltage vs Load Current Dropout Characteristics 10001719 10001720 Ground Pin Current vs Temperature and Load Ground Pin Current vs Load Current 10001721 10001722 11 www.national.com LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued) Input Current vs VIN Input Current vs VIN 10001724 10001723 Load Transient Response Load Transient Response 10001725 10001726 Line Transient Response Line Transient Response 10001727 www.national.com 10001728 12 Turn-On Waveform Turn-On Waveform 10001730 10001729 Short Circuit Current Short Circuit Current 10001731 10001732 Short Circuit Current vs Output Voltage Instantaneous Short Circuit Current vs Temperature 10001734 10001733 13 www.national.com LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued) LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued) Shutdown Pin Current vs Shutdown Pin Voltage DC Load Regulation 10001736 10001735 Shutdown Voltage vs Temperature Input to Output Leakage vs Temperature 10001738 10001737 Delay Pin Current vs Delay Pin Voltage Delay Pin Current vs VIN 10001748 10001745 www.national.com 14 Delay Sink Current vs Temperature Delay Sink Current vs Temperature 10001747 10001746 Output Impedance vs Frequency Output Impedance vs Frequency 10001740 10001741 Ripple Rejection (LP2987) Ripple Rejection (LP2988) 10001742 10001751 15 www.national.com LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued) LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued) Output Noise Density (LP2987) Output Noise Voltage (LP2988) 10001744 10001739 Output Noise Density (LP2988) Output Noise Density (LP2988) 10001752 10001753 Turn-On Time (LP2988) Turn-On Time (LP2988) 10001755 10001754 www.national.com 16 Turn-On Time (LP2988) 10001756 Basic Application Circuits 10001705 17 www.national.com LP2987/LP2988 Typical Performance Characteristics Unless otherwise specified: TA = 25C, COUT = 4.7 F, CIN = 2.2 F, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued) LP2987/LP2988 Basic Application Circuits (Continued) 10001706 *Capacitance value shown is minimum required to assure stability, but may be increased without limit. Larger output capacitor provides improved dynamic response. **Shutdown must be actively terminated (see Application Hints). Tie to INPUT (pin 4) if not used. Application Hints LLP Package Devices The LP2987/LP2988 is offered in the 8 lead LLP surface mount package to allow for increased power dissipation compared to the SO-8 and Mini SO-8. For details on thermal performance as well as mounting and soldering specifications, refer to Application Note AN-1187. ESR Curves For 5V Output EXTERNAL CAPACITORS As with any low-dropout regulator, external capacitors are required to assure stability. These capacitors must be correctly selected for proper performance. INPUT CAPACITOR: An input capacitor ( 2.2 F) is required between the LP2987/8 input and ground (amount of capacitance may be increased without limit). This capacitor must be located a distance of not more than 0.5" from the input pin and returned to a clean analog ground. Any good quality ceramic or tantalum may be used for this capacitor. OUTPUT CAPACITOR: The output capacitor must meet the requirement for minimum amount of capacitance and also have an appropriate E.S.R. (equivalent series resistance) value. Curves are provided which show the allowable ESR range as a function of load current for 3V and 5V outputs. 10001707 ESR Curves For 3V Output 10001708 www.national.com 18 POWER-ON RESET DELAY (Continued) A power-on reset function can be easily implemented using the LP2987/8 by adding a single external capacitor to the Delay pin. The Error output provides the power-on reset signal when input power is applied to the regulator. IMPORTANT: The output capacitor must maintain its ESR in the stable region over the full operating temperature range of the application to assure stability. The minimum required amount of output capacitance is 4.7 F. Output capacitor size can be increased without limit. The reset signal stays low for a pre-set time period after power is applied to the regulator, and then goes high (see Timing Diagram below). It is important to remember that capacitor tolerance and variation with temperature must be taken into consideration when selecting an output capacitor so that the minimum required amount of output capacitance is provided over the full operating temperature range. A good Tantalum capacitor will show very little variation with temperature, but a ceramic may not be as good (see next section). The output capacitor should be located not more than 0.5" from the output pin and returned to a clean analog ground. CAPACITOR CHARACTERISTICS TANTALUM: A solid tantalum capacitor is the best choice for the output capacitor on the LM2987/8. Available from many sources, their typical ESR is very close to the ideal value required on the output of many LDO regulators. Tantalums also have good temperature stability: a 4.7 F was tested and showed only a 10% decline in capacitance as the temperature was decreased from +125C to -40C. The ESR increased only about 2:1 over the same range of temperature. However, it should be noted that the increasing ESR at lower temperatures present in all tantalums can cause oscillations when marginal quality capacitors are used (where the ESR of the capacitor is near the upper limit of the stability range at room temperature). CERAMIC: The ESR of ceramic capacitor can be low enough to cause an LDO regulator to oscillate: a 2.2 F ceramic was measured and found to have an ESR of 15 m. If a ceramic capacitor is to be used on the LP2987/8 output, a 1 resistor should be placed in series with the capacitor to provide a minimum ESR for the regulator. A disadvantage of ceramic capacitors is that their capacitance varies a lot with temperature: Large ceramic capacitors are typically manufactured with the Z5U temperature characteristic, which results in the capacitance dropping by 50% as the temperature goes from 25C to 80C. This means you have to buy a capacitor with twice the minimum COUT to assure stable operation up to 80C. ALUMINUM: The large physical size of aluminum electrolytics makes them unsuitable for most applications. Their ESR characteristics are also not well suited to the requirements of LDO regulators. The ESR of a typical aluminum electrolytic is higher than a tantalum, and it also varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of 50X when going from 20C to -40C. Also, some aluminum electrolytics can not be used below -25C because the electrolyte will freeze. 10001709 Timing Diagram for Power-Up The external capacitor cDLY sets the delay time (TDELAY). The value of capacitor required for a given time delay may be calculated using the formula: CDLY = TDELAY/(5.59 X 105) To simplify design, a plot is provided below which shows values of CDLY versus delay time. 10001711 Plot of CDLY vs TDELAY 19 www.national.com LP2987/LP2988 Application Hints LP2987/LP2988 Application Hints Aluminum electrolytics can not be used, but good-quality tantalum, ceremic, mica, or film types will work. (Continued) DETAILS OF ERR/RESET CIRCUIT OPERATION: (Refer to LP2987/8 Equivalent Circuit). SHUTDOWN INPUT OPERATION The LP2987/8 is shut off by driving the Shutdown input low, and turned on by pulling it high. If this feature is not to be used, the Shutdown input should be tied to VIN to keep the regulator output on at all times. To assure proper operation, the signal source used to drive the Shutdown input must be able to swing above and below the specified turn-on/turn-off voltage thresholds listed as VH and VL, respectively (see Electrical Characteristics). It is also important that the turn-on (and turn-off) voltage signals applied to the Shutdown input have a slew rate which is not less than 40 mV/s. CAUTION: the regulator output state can not be guaranteed if a slow-moving AC (or DC) signal is applied that is in the range between VH and VL. REVERSE INPUT-OUTPUT VOLTAGE The PNP power transistor used as the pass element in the LP2987/8 has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reverse-biased. However, if the output is pulled above the input, this diode will turn ON and current will flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into VIN (and out the ground pin), which can damage the part. 10001710 LP2987/8 Equivalent Circuit In any application where the output may be pulled above the input, an external Schottky diode must be connected from VIN to VOUT (cathode on VIN, anode on VOUT), to limit the reverse voltage across the LP2987/8 to 0.3V (see Absolute Maximum Ratings). The output of comparator U2 is the ERR/RESET flag. Since it is an open-collector output, it requires the use of a pull-up resistor (RP). The 1.23V reference is tied to the inverting input of U2, which means that its output is controlled by the voltage applied to the non-inverting input. The output of U1 (also an open-collector) will force the non-inverting input of U2 to go low whenever the LP2987/8 regulated output drops about 5% below nominal. U1's inverting input is also held at 1.23V. The other input samples the regulated output through a resistive divider (RA and RB). When the regulated output is at nominal voltage, the voltage at the divider tap point will be 1.23V. If this voltage drops about 60 mV below 1.23V, the output of U1 will go low forcing the output of U2 low (which is the ERROR state). Power-ON reset delay occurs when a capacitor (shown as CDLY) is connected to the Delay pin. At turn-ON, this capacitor is initially fully discharged (which means the voltage at the Delay pin is 0V). The output of U1 keeps CDLY fully discharged (by sinking the 2.2 A from the current source) until the regulator output voltage comes up to within about 5% of nominal. At this point, U1's output stops sinking current and the 2.2 A starts charging up CDLY. When the voltage across CDLY reaches 1.23V, the output of U2 will go high (note that D1 limits the maximum voltage to about 2V). SELECTING CDLY: The maximum recommended value for this capacitor is 1 F. The capacitor must not have excessively high leakage current, since it is being charged from a 2.2 A current source. www.national.com BYPASS CAPACITOR (LP2988) The capacitor connected to the Bypass pin must have very low leakage. The current flowing out of the Bypass pin comes from the Bandgap reference, which is used to set the output voltage. Since the Bandgap circuit has only a few microamps flowing in it, loading effects due to leakage current will cause a change in the regulated output voltage. Curves are provided which show the effect of loading the Bypass pin on the regulated output voltage. Care must be taken to ensure that the capacitor selected for bypass will not have significant leakage current over the operating temperature range of the application. A high quality ceramic capacitor which uses either NPO or COG type dielectiric material will typically have very low leakage. Small surface-mount polypropolene or polycarbonate film capacitors also have extremely low leakage, but are slightly larger in size than ceramics. 20 LP2987/LP2988 Application Hints (Continued) 10001750 10001749 21 www.national.com LP2987/LP2988 Physical Dimensions inches (millimeters) unless otherwise noted Mini SO-8 Package Type MM NS Package Number MUA08A SO-8 Package Type M NS Package Number M08A www.national.com 22 inches (millimeters) unless otherwise noted (Continued) 8-Lead LLP Surface Mount Package NS Package Number LDC08A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 LP2987/LP2988 Micropower, 200 mA Ultra Low-Dropout Voltage Regulator with Programmable Power-On Reset Delay Physical Dimensions IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated