Typical Size 6,6 mm X 9,8 mm www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 !" FEATURES D Qualified for Automotive Applications D 30-m, 12-A Peak MOSFET Switches for High D D D D D D Efficiency at 6-A Continuous Output Source and Sink 0.9-V, 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V Fixed Output Voltage Devices With 1% Initial Accuracy Internally Compensated for Easy Use and Minimal Component Count Fast Transient Response Wide PWM Frequency - Fixed 350 kHz, 550 kHz or Adjustable 280 kHz to 700 kHz Load Protected by Peak Current Limit and Thermal Shutdown Integrated Solution Reduces Board Area and Total Cost APPLICATIONS D Low-Voltage, High-Density Systems With D D D DESCRIPTION The SWIFT family of dc/dc regulators, the TPS54611, TPS54612, TPS54613, TPS54614, TPS54615, and TPS54616 low-input voltage high-output current synchronous-buck PWM converters integrate all required active components. Included on the substrate are true, high-performance, voltage error amplifiers that provide high performance under transient conditions; an under-voltage-lockout circuit to prevent start-up until the input voltage reaches 3 V; an internally and externally set slow-start circuit to limit in-rush currents; and a power good output useful for processor/logic reset, fault signaling, and supply sequencing. The TPS54611-6 devices are available in a thermally enhanced 28-pin TSSOP (PWP) PowerPAD package, which eliminates bulky heatsinks. Texas Instruments provides evaluation modules and the SWIFT designer software tool to aid in quickly achieving high-performance power supply designs to meet aggressive equipment development cycles. Power Distributed at 5 V or 3.3 V Point of Load Regulation for High Performance DSPs, FPGAs, ASICs and Microprocessors Broadband, Networking and Optical Communications Infrastructure Portable Computing/Notebook PCs These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and SWIFT are trademarks of Texas Instruments. #$%&'()*#&$ # +,''-$* ) &% .,/0#+)*#&$ 1)*-2 '&1,+* +&$%&'( *& .-+#%#+)*#&$ .-' *3- *-'( &% -4) $*',(-$* *)$1)'1 5)'')$*62 '&1,+*#&$ .'&+-#$7 1&- $&* $-+-)'#06 #$+0,1- *-*#$7 &% )00 .)')(-*-'2 Copyright 2008 Texas Instruments Incorporated www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 EFFICIENCY AT 350 kHz 100 SIMPLIFIED SCHEMATIC 95 Output Input VIN 90 PH 85 Efficiency - % TPS54614 BOOT PGND VBIAS VSENSE AGND 80 75 70 65 60 55 50 0 1 2 3 4 5 6 Load Current - A PWP PACKAGE (TOP VIEW) AGND VSENSE NC PWRGD BOOT PH PH PH PH PH PH PH PH PH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 THERMAL 22 PAD 21 20 19 18 17 16 15 RT FSEL SS/ENA VBIAS VIN VIN VIN VIN VIN PGND PGND PGND PGND PGND AVAILABLE OPTIONS{ PACKAGED DEVICES} TJ OUTPUT VOLTAGE 0.9 V -40C -40 C to 125 125C C 1.2 V PLASTIC HTSSOP (PWP) TPS54611QPWPRQ1 TPS54612QPWPRQ1 PACKAGED DEVICES} TJ -40C -40 C to 125 125C C OUTPUT VOLTAGE PLASTIC HTSSOP (PWP) 1.8 V TPS54614QPWPRQ1 2.5 V TPS54615QPWPRQ1 1.5 V TPS54613QPWPRQ1 3.3 V TPS54616QPWPRQ1 For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at http://www.ti.com. Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging. The PWP package is taped and reeled as denoted by the R suffix on the device type (i.e., TPS54616QPWPRQ1). See application section of data sheet for PowerPAD drawing and layout information. Product Preview 2 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 Terminal Functions TERMINAL NAME DESCRIPTION NO. AGND 1 Analog ground. Return for slow-start capacitor, VBIAS capacitor, RT resistor FSEL. Make PowerPAD connection to AGND. BOOT 5 Bootstrap input. A 0.022-F to 0.1-F low-ESR capacitor connected from BOOT to PH generates a floating drive for the high-set FET driver. 3 No connection NC PGND 15-19 Power ground. High current return for the low-side driver and power MOSFET. Connect PGND with large copper areas to the input and output supply returns and negative terminals of the input and output capacitors. PH 6-14 Phase input/output. Junction of the internal high-side and low-side power MOSFETs, and output inductor. PWRGD 4 Power good open drain output. High-Z when VSENSE 90% Vref, otherwise PWRGD is low. Note that output is low when SS/ENA is low or internal shutdown signal active. RT 28 Frequency setting resistor input. Connect a resistor from RT to AGND to set the switching frequency. SS/ENA 26 Slow-start/enable input/output. Dual function pin which provides logic input to enable/disable device operation and capacitor input to externally set the start-up time. FSEL 27 Frequency select input. Provides logic input to select between two internally set switching frequencies. VBIAS 25 Internal bias regulator output. Supplies regulated voltage to internal circuitry. Bypass VBIAS pin to AGND pin with a high quality, low-ESR 0.1-F to 1-F ceramic capacitor. 20-24 Input supply for the power MOSFET switches and internal bias regulator. Bypass VIN pins to PGND pins close to device package with a high quality, low-ESR 1-F to 10-F ceramic capacitor. VIN VSENSE 2 Error amplifier inverting input. Connect directly to output voltage sense point. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) VI Input voltage range VO Output voltage range IO Source current IS Sink current VIN, SS/ENA, FSEL -0.3 V to 7 V RT -0.3 V to 6 V VSENSE -0.3 V to 4 V BOOT -0.3 V to 17 V VBIAS, PWRGD -0.3 V to 7 V PH -0.6 V to 10 V PH Internally Limited VBIAS PH Voltage differential 12 A SS/ENA, PWRGD 10 mA AGND to PGND 0.3 V Continuous power dissipation TJ Tstg 6 mA See Power Dissipation Rating Table Operating virtual junction temperature range -40C to 150C Storage temperature -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 300C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 3 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 DISSIPATION RATINGS(1)(2) PACKAGE THERMAL IMPEDANCE JUNCTION-TO-AMBIENT TA = 25C POWER RATING TA = 70C POWER RATING 28 pin PWP with solder 18.2C/W 5.49 W(3) 3.02 W 2.2 W 28 pn PWP without solder 40.5C/W 2.48 W 1.36 W 0.99 W (1) For more information on the PWP package, see the Texas Instruments technical brief, literature number SLMA002. (2) Test board conditions: 1. 3" x 3", 4 layers, thickness: 0.062" 2. 1.5 oz. copper traces located on the top of the PCB 3. 1.5 oz. copper ground plane on the bottom of the PCB 4. 0.5 oz. copper ground planes on the 2 internal layers 5. 12 thermal vias (see "Recommended Land Pattern" in applications section of this data sheet) (3) Maximum power dissipation may be limited by overcurrent protection. ADDITIONAL 6A SWIFT DEVICES DEVICE OUTPUT VOLTAGE TPS54610 0.9 V to 3.3 V TPS54672 DDR memory adjustable TPS54680 Sequencing adjustable TPS54673 Prebias adjustable RELATED DC/DC PRODUCTS D TPS40000--Low-input, voltage-mode synchronous buck controller D TPS759xx--7.5-A low dropout regulator D PT6440 series--6 A plugin modules 4 TA = 85C POWER RATING www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 ELECTRICAL CHARACTERISTICS TJ = -40C to 125C, VI = 3 V to 6 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY VOLTAGE, VIN VIN I(Q) Input voltage range 3 fs = 350 kHz, FSEL 0.8 V, RT open, phase pin open fs = 550 kHz, FSEL 2.5 V, RT open, phase pin open Quiescent current 6 9.8 Shutdown, SS/ENA = 0 V V 15 14 23 1 1.4 2.95 3 mA UNDER VOLTAGE LOCK OUT Start threshold voltage, UVLO Stop threshold voltage, UVLO 2.7 Hysteresis voltage, UVLO Rising and falling edge deglitch, UVLO(1) V 2.8 V 0.16 V 2.5 s BIAS VOLTAGE Output voltage, VBIAS Output current, VBIAS(2) I(VBIAS) = 0 2.7 2.8 2.95 V 100 A OUTPUT VOLTAGE VO TPS54611 TJ = 25C, VIN = 5 V 3 V VIN 6 V, 0 IL 6 A, -40 TJ 125C TPS54612 TJ = 25C, VIN = 5 V 3 V VIN 6 V, 0 IL 6 A, -40 TJ 125C TPS54613 TJ = 25C, VIN = 5 V 3 V VIN 6 V, 0 IL 6 A, -40 TJ 125C -2% TPS54614 TJ = 25C, VIN = 5 V 3 V VIN 6 V, 0 IL 6 A, -40 TJ 125C -3% TPS54615 TJ = 25C, VIN = 5 V 3.2 V VIN 6 V, 0 IL 6 A, -40 TJ 125C TPS54616 TJ = 25C, VIN = 5 V 4 V VIN 6 V, 0 IL 6 A, -40 TJ 125C Output voltage 0.9 -2% V 2% 1.2 -2% V 2% 1.5 V 2% 1.8 V 3% 2.5 -3% V 3% 3.3 -3% V 3% REGULATION Line regulation(1) (3) Load regulation(1) (3) IL = 3 A, 350 fs 550 kHz, TJ = 85C IL = 0 A to 6 A, 350 fs 550 kHz, TJ = 85C 0.088 %/V 0.0917 %/A (1) Specified by design (2) Static resistive loads only (3) Tested using circuit in Figure 10. 5 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 ELECTRICAL CHARACTERISTICS (CONTINUED) TJ = -40C to 125C, VI = 3 V to 6 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT OSCILLATOR Internally set--free running frequency Externally set--free running frequency range High level threshold, FSEL Low level threshold, FSEL Pulse duration, FSEL(1) Frequency range, FSEL(1) (4) Ramp valley(1) Ramp amplitude (peak-to-peak)(1) Minimum controllable on time(1) FSEL 0.8 V, RT open 265 350 440 FSEL 2.5 V, RT open 415 550 680 RT = 180 k (1% resistor to AGND)(1) 252 280 308 RT = 160 k (1% resistor to AGND) RT = 68 k (1% resistor to AGND)(1) 290 312 350 663 700 762 2.5 kHz V 0.8 50 V ns 330 700 0.75 kHz V 1 V 200 Maximum duty cycle(1) 90% (1) Specified by design (2) Static resistive loads only (3) Tested using circuit in Figure 10. (4) To ensure proper operation when RC filter is used between external clock and FSEL pin, the recommended values are R 1k and C 68 pF. 6 kHz ns www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 ELECTRICAL CHARACTERISTICS (CONTINUED) TJ = -40C to 125C, VI = 3 V to 6 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ERROR AMPLIFIER Error amplifier open loop voltage gain(1) Error amplifier unity gain bandwidth(1) 3 Error amplifier common mode input voltage range Powered by internal LDO(1) 26 dB 5 MHz 0 VBIAS V 70 85 ns 1.20 1.40 V PWM COMPARATOR PWM comparator propagation delay time, PWM comparator input to PH pin (excluding deadtime) 10-mV overdrive(1) SLOW-START/ENABLE Enable threshold voltage, SS/ENA 0.82 Enable hysteresis voltage, SS/ENA(1) Falling edge deglitch, SS/ENA(1) Internal slow-start time (1) 0.03 V s 2.5 TPS54611 2.6 3.3 4.1 TPS54612 3.5 4.5 5.4 TPS54613 4.4 5.6 6.7 TPS54614 2.6 3.3 4.1 TPS54615 3.6 4.7 5.6 TPS54616 ms 4.7 6.1 7.6 Charge current, SS/ENA SS/ENA = 0 V 2.5 5 8 A Discharge current, SS/ENA SS/ENA = 0.2 V, VI = 2.7 V 1.2 2.3 4.0 mA POWER GOOD Power good threshold voltage 90 Power good hysteresis voltage VSENSE falling See (1) 3 %VO %VO Power good falling edge deglitch See (1) 35 s Output saturation voltage, PWRGD I(sink) = 2.5 mA VI = 5.5 V Leakage current, PWRGD 0.18 0.3 V 1 A CURRENT LIMIT Current limit VI = 3 V VI = 6 V 7.2 10 10 12 Current limit leading edge blanking time (1) Current limit total response time(1) A 100 ns 200 ns THERMAL SHUTDOWN Thermal shutdown trip point(1) Thermal shutdown hysteresis(1) 135 150 165 10 _C OUTPUT POWER MOSFETS rDS(on) Power MOSFET switches IO = 3 A, VI = 6 V(2) IO = 3 A, VI = 3 V(2) 26 47 36 65 m (1) Specified by design (2) Matched MOSFETs, low side rDS(on) production tested, high side rDS(on) specified by design. 7 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 INTERNAL BLOCK DIAGRAM AGND VBIAS VIN Enable 5 A Comparator SS/ENA Falling Edge Deglitch 1.8 V Hysteresis: 0.03 V VIN UVLO Comparator VIN 2.94 V Hysteresis: 0.16 V VIN ILIM Comparator Thermal Shutdown 145C 2.5 s REG VBIAS SHUTDOWN VIN Leading Edge Blanking Falling and Rising Edge Deglitch 100 ns BOOT Sensefet 30 m 2.5 s SS_DIS SHUTDOWN Internal/External Slow-Start (Internal Slow-Start Time = 3.3 ms to 6.6 ms) VI VI Feed-Forward Compensation PH + - S 40 k Error Amplifier PWM Comparator 25 ns Adaptive Deadtime VIN 30 m OSC PGND Power good Comparator Reference/ DAC Falling Edge Deglitch VSENSE 0.90 Vref Hysteresis: 0.03 Vref TPS5461x VSENSE 8 CO Adaptive Dead-Time and Control Logic R Q 2 k LOUT RT FSEL SHUTDOWN 35 s PWRGD VO www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 TYPICAL CHARACTERISTICS DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE Drain-Source On-State Resistance - Drain-Source On-State Resistance - VI = 3.3 V IO = 3 A 100 80 60 40 20 -40 0 25 85 VI = 5 V IO = 3 A 80 60 40 20 0 -40 0 125 0 25 85 125 Figure 1 600 RT = 100 k 500 400 RT = 180 k 300 0.893 0.891 0.889 0.887 -80 -100 -120 -140 -160 0 -180 -20 -200 10 k 100 k 1 M 10 M 0 10 100 1k f - Frequency - Hz Figure 7 0.8890 f = 350 kHz 0.8870 0 25 85 125 3 4 5 VI - Input Voltage - V DEVICE POWER LOSSES vs LOAD CURRENT 5 TJ = 125C FS = 700 kHz 4.5 3.65 3.50 3.35 3.20 3.05 2.90 2.75 -40 6 Figure 6 3.80 Phase - Degrees -60 20 0.8910 -20 -40 125 0.8930 INTERNAL SLOW-START TIME vs JUNCTION TEMPERATURE Internal Slow-Start Time - ms RL= 10 k, CL = 160 pF, TA = 25C 85 TA = 85C Figure 5 0 140 Gain 25 TJ - Junction Temperature - C ERROR AMPLIFIER OPEN LOOP RESPONSE 40 0 0.8850 0.885 -40 125 Figure 4 60 250 -40 Device Power Losses - W 85 Phase 350 0.8950 TJ - Junction Temperature - C 80 FSEL 0.8 V OUTPUT VOLTAGE REGULATION vs INPUT VOLTAGE VO - Output Voltage Regulation - V Vref - Voltage Reference - V 700 100 450 Figure 3 0.895 120 550 TJ - Junction Temperature - C RT = 68 k 25 FSEL 2.5 V VOLTAGE REFERENCE vs JUNCTION TEMPERATURE 800 0 650 Figure 2 EXTERNALLY SET OSCILLATOR FREQUENCY vs JUNCTION TEMPERATURE 200 -40 750 TJ - Junction Temperature - C TJ - Junction Temperature - C f - Externally Set Oscillator Frequency - kHz f - Internally Set Oscillator Frequency -kHz 100 120 Gain - dB INTERNALLY SET OSCILLATOR FREQUENCY vs JUNCTION TEMPERATURE 4 VI = 3.3 V 3.5 3 2.5 2 1.5 VI = 5.0 V 1 0.5 0 0 25 85 TJ - Junction Temperature - C Figure 8 125 0 1 2 3 4 5 6 7 8 IL - Load Current - A Figure 9 9 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 APPLICATION INFORMATION Figure 10 shows the schematic diagram for a typical TPS54614 application. The TPS54614 (U1) can provide greater than 6 A of output current at a nominal output VI 3V-6V 20 220 F 10 F 21 voltage of 1.8 V. For proper operation, the exposed thermal PowerPAD underneath the integrated circuit package needs to be soldered to the printed-circuit board. VIN BOOT PH VIN 23 VIN NC 7 PH 8 PH 9 PH 10 PH 11 PH 12 PH 13 PH 14 PH 15 PGND PGND 16 VSENSE PGND VIN 10 k 27 28 26 25 4 Enable 0.1 F 6 VIN 22 24 PwrGood 5 3 2 CSS FSEL RT SS/ENA VBIAS PWRGD PGND 1 AGND PGND 0.047 F 7.2 H VO 1.8 V 680 F 17 18 19 PwrPad Figure 10. Application Circuit COMPONENT SELECTION OPERATING FREQUENCY The values for the components used in this design example were selected using the SWIFT designer software tool. SWIFT designer provides a complete design environment for developing dc-dc converters using the TPS54614, or other devices in the SWIFT product family. Additional design information is available at www.ti.com. In the application circuit, 350 kHz operation is selected by leaving FSEL open. Different operating frequencies can be selected by connecting a resistor between RT pin and AGND. Choose the value of R using Equation 1 for the desired operating frequency: INPUT FILTER The input to the circuit is a nominal 3.3 VDC or 5 VDC. The input filter is a 220-F POSCAP capacitor, with a maximum allowable ripple current of 3 A. A 10-F ceramic capacitor for the TPS54614 is required, and must be located as close as possible to the device. FEEDBACK CIRCUIT The output voltage of the converter is fed directly into the VSENSE pin of the TPS54614. The TPS54614 is internally compensated to provide stability of the output under varying line and load conditions. 10 R+ 500 kHz SwitchingFrequency 100 kW (1) Alternately, a preset operating frequency of 550 kHz can be selected by leaving RT open and connecting the FSEL pin to VI. OUTPUT FILTER The output filter is composed of a 5.2-H inductor and a 470-F capacitor. The inductor is low dc resistance (16-m) type, Sumida CDRH104R-5R2. The capacitor used is a 4-V POSCAP with a maximum ESR of 40 m. The output filter components work with the internal compensation network to provide a stable closed loop response for the converter. www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 GROUNDING AND POWERPAD LAYOUT The TPS54611-16 have two internal grounds (analog and power). Inside the TPS54611-16, the analog ground ties to all of the noise sensitive signals, while the power ground ties to the noisier power signals. The PowerPAD is tied internally to the analog ground. Noise injected between the two grounds can degrade the performance of the TPS54611-16, particularly at higher output currents. However, ground noise on an analog ground plane can also cause problems with some of the control and bias signals. For these reasons, separate analog and power ground planes are recommended. These two planes should tie together directly at the IC to reduce noise between the two grounds. The only components that should tie directly to the power ground plane are the input capacitor, the output capacitor, the input voltage decoupling capacitor, and the PGND pins of the TPS54611-16. The layout of the TPS54614 evaluation module is representative of a recommended layout for a 4-layer board. Documentation for the TPS54614 evaluation module can be found on the Texas Instruments web site (www.ti.com) under the TPS54614 product folder. See the TPS54614-185 User's Guide, Texas Instruments (SLVU053) and the application note, Texas Instruments (SLVA105). 8 PL O 0.0130 4 PL O 0.0180 LAYOUT CONSIDERATIONS FOR THERMAL PERFORMANCE For operation at full rated load current, the analog ground plane must provide adequate heat dissipating area. A 3 inch by 3 inch plane of 1 ounce copper is recommended, though not mandatory, depending on ambient temperature and airflow. Most applications have larger areas of internal ground plane available, and the PowerPAD should be connected to the largest area available. Additional areas on the top or bottom layers also help dissipate heat, and any area available should be used when 3 A or greater operation is desired. Connection from the exposes area of the PowerPAD to the analog ground plane layer should be made using 0.013 inch diameter vias to avoid solder wicking through the vias. Six vias should be in the PowerPAD area with four additional vias located under the device package. The size of the vias under the package, but not in the exposed thermal pad area, can be increased to 0.018. Additional vias beyond the 10 recommended that enhance thermal performance should be included in areas not under the device package. Minimum Recommended Thermal Vias: 8 x 0.013 Diameter Inside Powerpad Area 4 x 0.018 Diameter Under Device as Shown. Additional 0.018 Diameter Vias May Be Used if Top Side Analog Ground Area Is Extended. Connect Pin 1 to Analog Ground Plane in This Area for Optimum Performance 0.06 0.0150 0.0339 0.0650 0.0500 0.3820 0.3478 0.0500 0.0500 0.2090 0.0256 0.0650 0.0339 0.1700 0.1340 Minimum Recommended Top Side Analog Ground Area Minimum Recommended Exposed Copper Area for Powerpad. 5mm Stencils May Require 10 Percent Larger Area 0.0630 0.0400 Figure 11. Recommended Land Pattern for 28-Pin PWP PowerPAD 11 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 PERFORMANCE GRAPHS EFFICIENCY vs LOAD CURRENT OUTPUT VOLTAGE vs LOAD CURRENT 50 80 VI = 3.3V 70 60 40 1.01 Gain - dB VO - Output Voltage - V VI = 5 V 180 60 1.02 90 Efficiency - % LOOP RESPONSE 1.03 VI = 5 V 1 VI = 3.3V 30 90 20 Gain 10 0.99 135 Phase Phase - Degrees 100 45 0 0.98 -10 50 0.97 0 1 2 3 4 5 6 7 8 9 10 0 1 2 IL - Load Current - A 3 4 5 6 7 8 9 -20 10 100 IL - Load Current - A Figure 12 14 7 70 300 12 6 250 10 200 8 150 6 100 4 50 2 1 0 0 40 60 80 100 120 140 160 180 200 0 VO - Output Voltage - mV 350 VI - Input Voltage - V 80 I O - Output Current - A 8 VO - Output Voltage - mV 5 4 3 2 60 50 40 30 20 10 0 0 2 6 4 t - Time - s 8 10 12 14 16 18 20 Figure 15 Figure 16 125 TJ = 125C FS = 700 kHz 105 VI = 5 V 95 85 75 65 VI = 3.3 V 55 45 Safe Operating Area 35 25 0 1 2 3 4 5 6 IL - Load Current - A Figure 18 20 40 60 80 100 120 140 160 180 200 Figure 17 AMBIENT TEMPERATURE vs LOAD CURRENT 115 0 t - Time - s t - Time - s T A - Ambient Temperature - C 0 100 k OUTPUT RIPPLE VOLTAGE START-UP WAVEFORMS 16 20 10 k Figure 14 400 0 1k f - Frequency - Hz Figure 13 TRANSIENT RESPONSE 12 10 7 8 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 DETAILED DESCRIPTION Second, as the output becomes active, a brief ramp up at the internal slow-start rate may be observed before the externally set slow-start rate takes control and the output rises at a rate proportional to the slow-start capacitor. The slow-start time set by the capacitor is approximately: Under Voltage Lock Out (UVLO) The TPS5461x incorporates an under voltage lockout circuit to keep the device disabled when the input voltage (VIN) is insufficient. During power up, internal circuits are held inactive until VIN exceeds the nominal UVLO threshold voltage of 2.95 V. Once the UVLO start threshold is reached, device start-up begins. The device operates until VIN falls below the nominal UVLO stop threshold of 2.8 V. Hysteresis in the UVLO comparator and a 2.5-s rising and falling edge deglitch circuit reduces the likelihood of shutting the device down due to noise on VIN. Slow-Start/Enable (SS/ENA) The slow-start/enable pin provides two functions. First, the pin acts as an enable (shutdown) control by keeping the device turned off until the voltage exceeds the start threshold voltage of approximately 1.2 V. When SS/ENA exceeds the enable threshold, device start up begins. The reference voltage fed to the error amplifier is linearly ramped up from 0 V to 0.891 V in 3.35 ms. Similarly, the converter output voltage reaches regulation in approximately 3.35 ms. Voltage hysteresis and a 2.5-s falling edge deglitch circuit reduce the likelihood of triggering the enable due to noise. See the following table for start up times for each device DEVICE OUTPUT VOLTAGE SLOW-START TPS54611 0.9 V 3.3 ms TPS54612 1.2 V 4.5 ms TPS54613 1.5 V 5.6 ms TPS54614 1.8 V 3.3 ms TPS54615 2.5 V 4.7 ms TPS54616 3.3 V 6.1 ms 1.2 V 5 mA (SS) +C (SS) 0.7 V 5 mA (3) The actual slow-start time is likely to be less than the above approximation due to the brief ramp up at the internal rate. VBIAS Regulator The VBIAS regulator provides internal analog and digital blocks with a stable supply voltage over variations in junction temperature and input voltage. A high quality, low-ESR, ceramic bypass capacitor is required on the VBIAS pin. X7R or X5R grade dielectrics are recommended because their values are more stable over temperature. The bypass capacitor should be placed close to the VBIAS pin and returned to AGND. External loading on VBIAS is allowed, with the caution that internal circuits require a minimum VBIAS of 2.7 V, and external loads on VBIAS with ac or digital switching noise may degrade performance. The VBIAS pin may be useful as a reference voltage for external circuits. Voltage Reference The voltage reference system produces a precise, temperature-stable voltage from a bandgap circuit. A scaling amplifier and DAC are then used to produce the reference voltages for each of the fixed output devices. Oscillator and PWM Ramp The second function of the SS/ENA pin provides an external means for extending the slow-start time with a ceramic capacitor connected between SS/ENA and AGND. Adding a capacitor to the SS/ENA pin has two effects on start-up. First, a delay occurs between release of the SS/ENA pin and start-up of the output. The delay is proportional to the slow-start capacitor value and lasts until the SS/ENA pin reaches the enable threshold. The start-up delay is approximately: t +C d (SS) t (2) The oscillator frequency can be set to internally fixed values of 350 kHz or 550 kHz using the FSEL pin as a static digital input. If a different frequency of operation is required for the application, the oscillator frequency can be externally adjusted from 280 kHz to 700 kHz by connecting a resistor from the RT pin to AGND and floating the FSEL pin. The switching frequency is approximated by the following equation, where R is the resistance from RT to AGND: Switching Frequency + 100 kW R 500 [kHz] (4) External synchronization of the PWM ramp is possible over the frequency range of 330 kHz to 700 kHz by driving a synchronization signal into FSEL and connecting a resistor from RT to AGND. Choose an RT resistor that sets the free-running frequency to 80% of the synchronization signal. Table 1 summarizes the frequency selection configurations. 13 www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 Table 1. Summary of the Frequency Selection Configurations SWITCHING FREQUENCY FSEL PIN RT PIN 350 kHz, internally set Float or AGND Float 550 kHz, internally set 2.5 V Float Externally set 280 kHz to 700 kHz Float R = 68 k to 180 k Externally synchronized frequency(1) Synchronization signal R = RT value for 80% of external synchronization frequency (1) To ensure proper operation when RC filter is used between external clock and FSEL pin, the recommended values are R 1k and C 68 pF. rises to the regulation set-point, setting VSENSE to approximately the same voltage as Vref. If the error amplifier output is low, the PWM latch is continually reset and the high-side FET does not turn on. The low-side FET remains on until the VSENSE voltage decreases to a range that allows the PWM comparator to change states. The TPS54611-TPS54616 devices are capable of sinking current continuously until the output reaches the regulation set-point. If the current limit comparator trips for longer than 100 ns, the PWM latch resets before the PWM ramp exceeds the error amplifier output. The high-side FET turns off and the low-side FET turns on to decrease the energy in the output inductor and consequently decrease the output current. This process is repeated each cycle in which the current limit comparator is tripped. Dead-Time Control and MOSFET Drivers Error Amplifier The high performance, wide bandwidth, voltage error amplifier is gain-limited to provide internal compensation of the control loop. The user is given limited flexibility in choosing output L and C filter components. Inductance values of 4.7 H to 10 H are typical and available from several vendors. The resulting designs exhibit good noise and ripple characteristics, but with exceptional transient response. Transient recovery times are typically in the range of 10 s to 20 s. PWM Control Signals from the error amplifier output, oscillator, and current limit circuit are processed by the PWM control logic. Referring to the internal block diagram, the control logic includes the PWM comparator, OR gate, PWM latch, and portions of the adaptive dead-time and control logic block. During steady-state operation below the current limit threshold, the PWM comparator output and oscillator pulse train alternately set and reset the PWM latch. Once the PWM latch is set, the low-side FET remains on for a minimum duration set by the oscillator pulse width. During this period, the PWM ramp discharges rapidly to its valley voltage. When the ramp begins to charge back up, the low-side FET turns off and high-side FET turns on. As the PWM ramp voltage exceeds the error amplifier output voltage, the PWM comparator resets the latch, thus turning off the high-side FET and turning on the low-side FET. The low-side FET remains on until the next oscillator pulse discharges the PWM ramp. During transient conditions, the error amplifier output could be below the PWM ramp valley voltage or above the PWM peak voltage. If the error amplifier is high, the PWM latch is never reset, and the high-side FET remains on until the oscillator pulse signals the control logic to turn the high-side FET off and the low-side FET on. The device operates at its maximum duty cycle until the output voltage 14 Adaptive dead-time control prevents shoot-through current from flowing in both N-channel power MOSFETs during the switching transitions by actively controlling the turnon times of the MOSFET drivers. The high-side driver does not turn on until the voltage at the gate of the low-side FET is below 2 V. The high-side and low-side drivers are designed with 300-mA source and sink capability to quickly drive the power MOSFETs gates. The low-side driver is supplied from VIN, while the high-side drive is supplied from the BOOT pin. A bootstrap circuit uses an external BOOT capacitor and internal 2.5- bootstrap switch connected between the VIN and BOOT pins. The integrated bootstrap switch improves drive efficiency and reduces external component count. Overcurrent Protection Cycle-by-cycle current limiting is achieved by sensing the current flow through the high-side MOSFET and a differential amplifier with preset overcurrent threshold. The high-side MOSFET is turned off within 200 ns of reaching the current limit threshold. A 100-ns leading edge blanking circuit prevents false tripping of current limit. Current limit detection occurs only when current flows from VIN to PH when sourcing current to the output filter. Load protection during current sink operation is provided by thermal shutdown. Thermal Shutdown The device uses the thermal shutdown to turn off the power MOSFETs and disable the controller if the junction temperature exceeds 150C. The device is released from shutdown when the junction temperature decreases to 10C below the thermal shutdown trip point, and starts up under control of the slow-start circuit. Thermal shutdown provides protection when an overload condition is sustained for several milliseconds. With a persistent fault condition, the device cycles continuously: starting up by www.ti.com SGLS266G - OCTOBER 2004 - REVISED JUNE 2008 control of the slow-start circuit, heating up due to the fault, and then shutting down upon reaching the thermal shutdown trip point. Power Good (PWRGD) The power good circuit monitors for under voltage conditions on VSENSE. If the voltage on VSENSE falls 10% below the reference voltage, the open-drain PWRGD output is pulled low. PWRGD is also pulled low if VIN is less than the UVLO threshold, or SS/ENA is low, or thermal shutdown is asserted. When VIN = UVLO threshold, SS/ENA = enable threshold, and VSENSE > 90% of Vref, the open drain output of the PWRGD pin is high. A hysteresis voltage equal to 3% of Vref and a 35-s falling edge deglitch circuit prevent tripping of the power good comparator due to high-frequency noise. 15 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty 2000 Green (RoHS & no Sb/Br) Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) TPS54612QPWPRQ1 ACTIVE HTSSOP PWP 28 TPS54613QPWPRQ1 ACTIVE HTSSOP PWP 28 TPS54614QPWPRQ1 ACTIVE HTSSOP PWP 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS54615QPWPRQ1 ACTIVE HTSSOP PWP 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS54616QPWPRQ1 ACTIVE HTSSOP PWP 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TBD Samples CU NIPDAU Level-2-260C-1 YEAR Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 OTHER QUALIFIED VERSIONS OF TPS54612-Q1, TPS54613-Q1, TPS54614-Q1, TPS54615-Q1, TPS54616-Q1 : * Catalog: TPS54612, TPS54613, TPS54614, TPS54615, TPS54616 * Enhanced Product: TPS54612-EP, TPS54613-EP, TPS54614-EP, TPS54615-EP, TPS54616-EP NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated