SMAJ5.0A thru SMAJ188CA www.vishay.com Vishay General Semiconductor Surface-Mount TRANSZORB(R) Transient Voltage Suppressors FEATURES * Low profile package * Ideal for automated placement * Glass passivated chip junction * Available in uni-directional and bi-directional Available * 400 W peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % (300 W above 78 V) SMA (DO-214AC) * Excellent clamping capability LINKS TO ADDITIONAL RESOURCES 3D 3D * Very fast response time * Low incremental surge resistance * Meets MSL level 1, per J-STD-020, LF maximum peak of 260 C 3D Models * AEC-Q101 qualified available - Automotive ordering code: base P/NHE3 or P/NHM3 PRIMARY CHARACTERISTICS VBR uni-directional 6.40 V to 231 V VBR bi-directional 6.40 V to 231 V VWM 5.0 V to 188 V PPPM 400 W, 300 W IFSM 40 A TJ max. 150 C Polarity Uni-directional, bi-directional Package SMA (DO-214AC) DEVICES FOR BI-DIRECTION APPLICATIONS For bi-directional use CA suffix (e.g. SMAJ10CA). Electrical characteristics apply in both directions. TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA Case: SMA (DO-214AC) Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS-compliant, commercial grade Base P/N-M3 - halogen-free, RoHS-compliant, commercial grade Base P/NHE3_X - RoHS-compliant and AEC-Q101 qualified Base P/NHM3_X - halogen-free, RoHS-compliant, and AEC-Q101 qualified ("_X" denotes revision code e.g. A, B, ...) Terminals: matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 E3, M3, HE3, and HM3 suffix meets JESD 201 class 2 whisker test Polarity: for uni-directional types the band denotes cathode end, no marking on bi-directional types MAXIMUM RATINGS (TA = 25 C unless otherwise noted) SYMBOL VALUE UNIT Peak pulse power dissipation with a 10/1000 s waveform (1)(2) (fig. 1) PARAMETER PPPM 400 W Peak pulse current with a waveform (1) IPPM See next table A Peak forward surge current 8.3 ms single half sine-wave uni-directional only (2) Operating junction and storage temperature range IFSM 40 A TJ, TSTG -55 to +150 C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 C per fig. 2. Rating is 300 W above 78 V A (2) Mounted on 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads to each terminal Revision: 20-Jul-2020 Document Number: 88390 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMAJ5.0A thru SMAJ188CA www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 C unless otherwise noted) DEVICE TYPE (+)SMAJ5.0A (5) (+)SMAJ6.0A (+)SMAJ6.5A (+)SMAJ7.0A (+)SMAJ7.5A (+)SMAJ8.0A (+)SMAJ8.5A (+)SMAJ9.0A (+)SMAJ10A (+)SMAJ11A (+)SMAJ12A (+)SMAJ13A (+)SMAJ14A (+)SMAJ15A (+)SMAJ16A (+)SMAJ17A (+)SMAJ18A (+)SMAJ20A (+)SMAJ22A (+)SMAJ24A (+)SMAJ26A (+)SMAJ28A (+)SMAJ30A (+)SMAJ33A (+)SMAJ36A (+)SMAJ40A (+)SMAJ43A (+)SMAJ45A (+)SMAJ48A (+)SMAJ51A (+)SMAJ54A (+)SMAJ58A (+)SMAJ60A (+)SMAJ64A (+)SMAJ70A (+)SMAJ75A (+)SMAJ78A (+)SMAJ85A (+)SMAJ90A (+)SMAJ100A (+)SMAJ110A (+)SMAJ120A (+)SMAJ130A (+)SMAJ150A (+)SMAJ160A (+)SMAJ170A (+)SMAJ188A DEVICE MARKING CODE UNI AE AG AK AM AP AR AT AV AX AZ BE BG BK BM BP BR BT BV BX BZ CE CG CK CM CP CR CT CV CX CZ RE RG RK RM RP RR RT RV RX RZ SE VG VK VM SP SR SS BI WE WG WK WM WP WR WT WV WX WZ XE XG XK XM XP XR XT XV XX XZ YE YG YK YM YP YR YT YV YX YZ ZE ZG ZK ZM ZP ZR ZT ZV ZX ZZ VE VG VK VM VP VR VS BREAKDOWN VOLTAGE VBR AT IT (1) (V) MIN. 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.0 11.1 12.2 13.3 14.4 15.6 16.7 17.8 18.9 20.0 22.2 24.4 26.7 28.9 31.1 33.3 36.7 40.0 44.4 47.8 50.0 53.3 56.7 60.0 64.4 66.7 71.1 77.8 83.3 86.7 94.4 100 111 122 133 144 167 178 189 209 MAX. 7.07 7.37 7.98 8.60 9.21 9.83 10.4 11.1 12.3 13.5 14.7 15.9 17.2 18.5 19.7 20.9 22.1 24.5 26.9 29.5 31.9 34.4 36.8 40.6 44.2 49.1 52.8 55.3 58.9 62.7 66.3 71.2 73.7 78.6 86.0 92.1 95.8 104 111 123 135 147 159 185 197 209 231 TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM ID (A) (3) 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10 11 12 13 14 15 16 17 18 20 22 24 26 28 30 33 36 40 43 45 48 51 54 58 60 64 70 75 78 85 90 100 110 120 130 150 160 170 188 800 800 500 200 100 50 10 5.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 MAXIMUM MAXIMUM PEAK PULSE CLAMPING SURGE VOLTAGE AT CURRENT IPPM (2) IPPM (A) VC (V) 43.5 38.8 35.7 33.3 31.0 29.4 27.8 26.0 23.5 22.0 20.1 18.6 17.2 16.4 15.4 14.5 13.7 12.3 11.3 10.3 9.5 8.8 8.3 7.5 6.9 6.2 5.8 5.5 5.2 4.9 4.6 4.3 4.1 3.9 3.5 3.3 3.2 2.2 2.1 1.9 1.7 1.6 1.4 1.2 1.2 1.09 0.91 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103 113 121 126 137 146 162 177 193 209 243 259 275 328 Notes (1) Pulse test: t 50 ms p (2) Surge current waveform per fig. 3 and derate per fig. 2 (3) For bi-directional types having V WM of 10 V and less, the ID limit is doubled (4) All terms and symbols are consistent with ANSI/IEEE C62.35 (5) For the bi-directional SMAJ5.0CA, the maximum V BR is 7.25 V (6) V = 3.5 V at I = 25 A (uni-directional only) F F (+) Underwriters Laboratory Recognition for the classification of protectors (QVGQ2) under the UL standard for safety 497B and file number E136766 for both uni-directional and bi-directional device Revision: 20-Jul-2020 Document Number: 88390 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMAJ5.0A thru SMAJ188CA www.vishay.com Vishay General Semiconductor THERMAL CHARACTERISTICS (TA = 25 C unless otherwise noted) PARAMETER Typical thermal resistance, junction to ambient (1) Typical thermal resistance, junction to lead SYMBOL RJA RJL VALUE 120 30 UNIT C/W C/W Note (1) Mounted on minimum recommended pad layout ORDERING INFORMATION (Example) PREFERRED P/N SMAJ5.0A-E3/61 SMAJ5.0A-M3/61 SMAJ5.0A-E3/5A SMAJ5.0A-M3/5A SMAJ5.0AHE3_A/H (1) SMAJ5.0AHM3_A/H (1) SMAJ5.0AHE3_A/I (1) SMAJ5.0AHM3_A/I (1) UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE 0.064 61 1800 7" diameter plastic tape and reel 0.064 5A 7500 13" diameter plastic tape and reel 0.064 H 1800 7" diameter plastic tape and reel 0.064 I 7500 13" diameter plastic tape and reel Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 150 Non-Repetitive Pulse Waveform Shown in Fig. 3 TA = 25 C 10 1 0.2" x 0.2" (5.0 mm x 5.0 mm) Copper Pad Areas 0.1 0.1 tr = 10 s TJ = 25 C Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50 % of IPPM Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 s Waveform as Defined by R.E.A. td 0 1 10 100 1000 10 000 0 1.0 2.0 3.0 td - Pulse Width (s) t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform 100 4.0 10 000 CJ - Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % SMAJ5.0 thru SMAJ78 SMAJ85 thru SMAJ188 IPPM - Peak Pulse Current, % IRSM PPPM - Peak Pulse Power (kW) 100 75 50 25 0 Measured at Stand-off Voltage VWM TJ = 25 C f = 1.0 MHz Vsig = 50 mVp-p 1000 Uni-Directional 100 Bi-Directional 10 0 25 50 75 100 125 150 175 200 1 10 100 TJ - Initial Temperature (C) VWM - Reverse Stand-Off Voltage (V) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Fig. 4 - Typical Junction Capacitance 200 Revision: 20-Jul-2020 Document Number: 88390 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMAJ5.0A thru SMAJ188CA www.vishay.com Vishay General Semiconductor 200 Peak Forward Surge Current (A) Transient Thermal Impedance (C/W) 1000 100 10 1 0.001 TJ = TJ Max. 8.3 ms Single Half Sine-Wave 100 50 10 0.01 0.1 1.0 10 100 1000 1 10 100 tp - Pulse Duration (s) Number of Cycles at 60 Hz Fig. 5 - Typical Transient Thermal Impedance Fig. 6 - Maximum Non-Repetitive Forward Surge Current Uni-Directional Only PACKAGE OUTLINE DIMENSIONS in inches (millimeters) SMA (DO-214AC) Cathode Band Mounting Pad Layout 0.110 (2.79) 0.100 (2.54) 0.065 (1.65) 0.049 (1.25) 0.177 (4.50) 0.157 (3.99) 0.012 (0.305) 0.006 (0.152) 0.060 (1.52) MIN. 0.208 (5.28) REF. 0.090 (2.29) 0.078 (1.98) 0.060 (1.52) 0.030 (0.76) 0.074 (1.88) MAX. 0.066 (1.68) MIN. 0.008 (0.203) 0 (0) 0.208 (5.28) 0.194 (4.93) Revision: 20-Jul-2020 Document Number: 88390 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2021 1 Document Number: 91000