SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 FEATURES 1 1DIR 2 15 1OE VCCA VCCB 2DIR 3 14 2OE 1 16 16 15 14 13 1A1 4 13 1B1 1DIR 2 15 1OE 1A2 5 12 1B2 2DIR 3 14 2OE 2A1 6 11 2B1 1A1 4 13 1B1 2A2 7 10 2B2 5 12 GND 8 9 GND 1A2 2A1 6 11 1B2 2B1 2A2 7 10 2B2 8 9 1B2 VCCB 2B1 16 12 2B2 2 11 GND 3 10 GND 9 2A2 1 1OE VCCB VCCA 1DIR 4 5 6 7 8 2A1 1 2OE VCCA 1B1 RSV PACKAGE (TOP VIEW) RGY PACKAGE (TOP VIEW) 1A2 D, DGV, OR PW PACKAGE (TOP VIEW) 1A1 * 2DIR * * Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 8000-V Human-Body Model (A114-A) - 150-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) * GND * * Control Inputs VIH/VIL Levels Are Referenced to VCCA Voltage Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.2-V to 3.6-V Power-Supply Range I/Os Are 4.6-V Tolerant Ioff Supports Partial Power-Down-Mode Operation Maximim Data Rates - 380 Mbps (1.8-V to 3.3-V Translation) - 200 Mbps (<1.8-V to 3.3-V Translation) - 200 Mbps (Translate to 2.5 V or 1.8 V) - 150 Mbps (Translate to 1.5 V) - 100 Mbps (Translate to 1.2 V) GND * DESCRIPTION/ORDERING INFORMATION This 4-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.2 V to 3.6 V. The SN74AVC4T245 is optimized to operate with VCCA/VCCB set at 1.4 V to 3.6 V. It is operational with VCCA/VCCB as low as 1.2 V. This allows for universal low-voltage bidirectional translation between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes. The SN74AVC4T245 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ. The SN74AVC4T245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCA. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2007, Texas Instruments Incorporated SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 DESCRIPTION/ORDERING INFORMATION (CONTINUED) The VCC isolation feature ensures that if either VCC input is at GND, then both ports are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION TA -40C to 85C PACKAGE ORDERABLE PART NUMBER TOP-SIDE MARKING QFN - RGY Tape and reel SN74AVC4T245RGYR WT245 QFN - RSV Tape and reel SN74AVC4T245RSVR 2WU Tube SN74AVC4T245D Tape and reel SN74AVC4T245DR Tube SN74AVC4T245PW Tape and reel SN74AVC4T245PWR Tape and reel SN74AVC4T245DGVR SOIC - D TSSOP - PW TVSOP - DGV (1) (2) (1) (2) AVC4T245 WT245 WT245 Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. FUNCTION TABLE (1) (each 2-bit section) CONTROL INPUTS (1) OUTPUT CIRCUITS OPERATION OE DIR A PORT B PORT L L Enabled Hi-Z B data to A bus L H Hi-Z Enabled A data to B bus H X Hi-Z Hi-Z Isolation Input circuits of the data I/Os are always active. LOGIC DIAGRAM (POSITIVE LOGIC) FOR 1/2 OF AVC4T245 DIR OE A1 B1 A2 B2 2 Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 www.ti.com SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) MIN MAX -0.5 4.6 I/O ports (A port) -0.5 4.6 I/O ports (B port) -0.5 4.6 Control inputs -0.5 4.6 A port -0.5 4.6 B port -0.5 4.6 A port -0.5 VCCA + 0.5 B port -0.5 VCCB + 0.5 VCCA Supply voltage range VCCB VI Input voltage range (2) UNIT V V VO Voltage range applied to any output in the high-impedance or power-off state (2) VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA 100 mA Continuous current through VCCA, VCCB, or GND D package (4) Package thermal impedance DGV package 82 (4) 120 PW package (4) 108 RGY package (5) (1) (2) (3) (4) (5) Storage temperature range C/W 39 RSV package Tstg V 73 DB package (4) JA V 184 -65 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input voltage and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed. The package thermal impedance is calculated in accordance with JESD 51-7. The package thermal impedance is calculated in accordance with JESD 51-5. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 3 SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 RECOMMENDED OPERATING CONDITIONS (1) (2) (3) VCCI VCCO MIN MAX UNIT VCCA Supply voltage 1.2 3.6 V VCCB Supply voltage 1.2 3.6 V High-level input voltage VIH Low-level input voltage VIL High-level input voltage VIH VIL Low-level input voltage VI Input voltage Data inputs (4) Data inputs (4) DIR (referenced to VCCA) (5) DIR (referenced to VCCA) (5) 1.2 V to 1.95 V VCCI x 0.65 1.95 V to 2.7 V 1.6 2.7 V to 3.6 V 2 1.2 V to 1.95 V VCCI x 0.35 1.95 V to 2.7 V 0.7 2.7 V to 3.6 V 0.8 1.2 V to 1.95 V VCCA x 0.65 1.95 V to 2.7 V 1.6 2.7 V to 3.6 V 2 Output voltage IOH VCCA x 0.35 1.95 V to 2.7 V 0.7 IOL 3.6 Active state 0 VCCO 3-state 0 3.6 Low-level output current t/v Input transition rise or fall rate TA Operating free-air temperature (1) (2) (3) (4) (5) 4 V 0.8 0 High-level output current V V 1.2 V to 1.95 V 2.7 V to 3.6 V VO V 1.2 V -3 1.4 V to 1.6 V -6 1.65 V to 1.95 V -8 2.3 V to 2.7 V -9 3 V to 3.6 V -12 1.1 V to 1.2 V 3 1.4 V to 1.6 V 6 1.65 V to 1.95 V 8 2.3 V to 2.7 V 9 3 V to 3.6 V 12 -40 V V mA mA 5 ns/V 85 C VCCI is the VCC associated with the input port. VCCO is the VCC associated with the output port. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. For VCCI values not specified in the data sheet, VIH min = VCCI x 0.7 V, VIL max = VCCI x 0.3 V For VCCI values not specified in the data sheet, VIH min = VCCA x 0.7 V, VIL max = VCCA x 0.3 V Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 ELECTRICAL CHARACTERISTICS (1) (2) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = -100 A VOH VCCB TA = 25C MIN TYP 1.2 V to 3.6 V 1.2 V to 3.6 V 1.2 V 1.4 V 1.4 V 1.05 1.65 V 1.65 V 1.2 IOH = -9 mA 2.3 V 2.3 V 1.75 IOH = -12 mA 3V 3V 2.3 VI = VIH 0.2 1.2 V 1.2 V IOL = 6 mA 1.4 V 1.4 V 0.35 1.65 V 1.65 V 0.45 IOL = 9 mA 2.3 V 2.3 V 0.55 IOL = 12 mA 3V 3V 0.7 II Ioff A or B port VI or VO = 0 to 3.6 V IOZ A or B port VI = VCCA or GND 1.2 V to 3.6 V 1.2 V to 3.6 V VO = VCCO or GND, VI = VCCI or GND, OE = VIH 0.25 0.025 0.25 1 0V 0 V to 3.6 V 0.1 1 5 0 V to 3.6 V 0V 0.1 1 5 3.6 V 3.6 V 0.5 2.5 5 1.2 V to 3.6 V 1.2 V to 3.6 V VI = VCCI or GND, IO = 0 VI = VCCI or GND, IO = 0 VI = VCCI or GND, IO = 0 Ci Control inputs 0 V to 3.6 V -2 0 V to 3.6 V 0V 8 Cio A or B port VO = 3.3 V or GND A A A A 8 0V 0 V to 3.6 V 8 0 V to 3.6 V 0V -2 1.2 V to 3.6 V 1.2 V to 3.6 V VI = 3.3 V or GND V 8 0V 1.2 V to 3.6 V 1.2 V to 3.6 V (1) (2) V IOL = 3 mA VI = VIL UNIT 0.95 1.2 V to 3.6 V 1.2 V to 3.6 V Control inputs ICCA + ICCB MAX VCCO - 0.2 1.2 V IOL = 8 mA ICCB MIN IOH = -6 mA IOL = 100 A ICCA -40C to 85C MAX IOH = -3 mA IOH = -8 mA VOL VCCA A 16 A 3.3 V 3.3 V 3.5 4.5 pF 3.3 V 3.3 V 6 7 pF VCCO is the VCC associated with the output port. VCCI is the VCC associated with the input port. Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 5 SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 SWITCHING CHARACTERISTICS over recommended operating free-air temperature range, VCCA = 1.2 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP TYP TYP TYP TYP 3.4 2.9 2.7 2.6 2.8 3.4 2.9 2.7 2.6 2.8 3.6 3.1 2.8 2.6 2.6 3.6 3.1 2.8 2.6 2.6 5.6 4.7 4.3 3.9 3.7 5.6 4.7 4.3 3.9 3.7 5 4.3 3.9 3.6 36.6 5 4.3 3.9 3.6 3.6 6.2 5.2 5.2 4.3 4.8 6.2 5.2 5.2 4.3 4.8 5.9 5.1 5 4.7 5.5 5.9 5.1 5 4.7 5.5 UNIT ns ns ns ns ns ns SWITCHING CHARACTERISTICS over recommended operating free-air temperature range, VCCA = 1.5 V 0.1 V (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ 6 FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 3.2 0.3 6.3 0.3 5.2 0.4 4.2 0.4 4.2 3.2 0.3 6.3 0.3 5.2 0.4 4.2 0.4 4.2 3.3 0.7 6.3 0.5 6 0.4 5.7 0.3 5.6 3.3 0.7 6.3 0.5 6 0.4 5.7 0.3 5.6 4.9 1.4 9.6 1.1 9.5 0.7 9.4 0.4 9.4 4.9 1.4 9.6 1.1 9.5 0.7 9.4 0.4 9.4 4.5 1.4 9.6 1.1 7.7 0.9 5.8 0.9 5.6 4.5 1.4 9.6 1.1 7.7 0.9 5.8 0.9 5.6 5.6 1.8 10.2 1.5 10.2 1.3 10.2 1.6 10.2 5.6 1.8 10.2 1.5 10.2 1.3 10.2 1.6 10.2 5.2 1.9 10.3 1.9 9.1 1.4 7.4 1.2 7.6 5.2 1.9 10.3 1.9 9.1 1.4 7.4 1.2 7.6 Submit Documentation Feedback UNIT ns ns ns ns ns ns Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 SWITCHING CHARACTERISTICS over recommended operating free-air temperature range, VCCA = 1.8 V 0.15 V (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V UNIT TYP MIN MAX MIN MAX MIN MAX MIN MAX 2.9 0.1 6 0.1 4.9 0.1 3.9 0.3 3.9 2.9 0.1 6 0.1 4.9 0.1 3.9 0.3 3.9 3 0.6 5.3 0.5 4.9 0.3 4.6 0.3 4.5 3 0.6 5.3 0.5 4.9 0.3 4.6 0.3 4.5 4.4 1 7.4 1 7.3 0.6 7.3 0.4 7.2 4.4 1 7.4 1 7.3 0.6 7.3 0.4 7.2 4.1 1.2 9.2 1 7.4 0.8 5.3 0.8 4.6 4.1 1.2 9.2 1 7.4 0.8 5.3 0.8 4.6 5.4 1.6 8.6 1.8 8.7 1.3 8.7 1.6 8.7 5.4 1.6 8.6 1.8 8.7 1.3 8.7 1.6 8.7 5 1.7 9.9 1.6 8.7 1.2 6.9 1 6.9 5 1.7 9.9 1.6 8.7 1.2 6.9 1 6.9 ns ns ns ns ns ns SWITCHING CHARACTERISTICS over recommended operating free-air temperature range, VCCA = 2.5 V 0.2 V (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 2.8 0.1 5.7 0.1 4.6 0.2 3.5 0.1 3.6 2.8 0.1 5.7 0.1 4.6 0.2 3.5 0.1 3.6 2.7 0.6 4.2 0.4 3.9 0.2 3.4 0.2 3.3 2.7 0.6 4.2 0.4 3.9 0.2 3.4 0.2 3.3 4 0.7 6.5 0.7 5.2 0.6 4.8 0.4 4.8 4 0.7 6.5 0.7 5.2 0.6 4.8 0.4 4.8 3.8 0.9 8.8 0.8 7 0.6 4.8 0.6 4 3.8 0.9 8.8 0.8 7 0.6 4.8 0.6 4 4.7 1 8.4 1 8.4 1 6.2 1 6.6 4.7 1 8.4 1 8.4 1 6.2 1 6.6 4.5 1.5 9.4 1.3 8.2 1.1 6.2 0.9 5.2 4.5 1.5 9.4 1.3 8.2 1.1 6.2 0.9 5.2 Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 UNIT ns ns ns ns ns ns 7 SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 SWITCHING CHARACTERISTICS over recommended operating free-air temperature range, VCCA = 3.3 V 0.3 V (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) A B B A OE A OE B OE A OE B tPLH tPHL tPLH tPHL tPZH tPZL tPZH tPZL tPHZ tPLZ tPHZ tPLZ VCCB = 1.2 V VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V TYP MIN MAX MIN MAX MIN MAX MIN MAX 2.9 0.1 5.6 0.1 4.5 0.1 3.3 0.1 2.9 2.9 0.1 5.6 0.1 4.5 0.1 3.3 0.1 2.9 2.6 0.6 4.2 0.4 3.4 0.2 3 0.1 2.8 2.6 0.6 4.2 0.4 3.4 0.2 3 0.1 2.8 3.8 0.6 8.7 0.6 5.2 0.6 3.8 0.4 3.8 3.8 0.6 8.7 0.6 5.2 0.6 3.8 0.4 3.8 3.7 0.8 8.7 0.6 6.8 0.5 4.7 0.5 3.8 3.7 0.8 8.7 0.6 6.8 0.5 4.7 0.5 3.8 4.8 0.7 9.3 0.7 8.3 0.7 5.6 0.7 6.6 4.8 0.7 9.3 0.7 8.3 0.7 5.6 0.7 6.6 5.3 1.4 9.3 1.2 8.1 1 6.4 0.8 6.2 5.3 1.4 9.3 1.2 8.1 1 6.4 0.8 6.2 UNIT ns ns ns ns ns ns OPERATING CHARACTERISTICS TA = 25C VCCA = VCCB = 1.2 V VCCA = VCCB = 1.5 V VCCA = VCCB = 1.8 V VCCA = VCCB = 2.5 V VCCA = VCCB = 3.3 V TYP TYP TYP TYP TYP 1 1 1 1.5 2 1 1 1 1 1 12 12.5 13 14 15 Outputs disabled 1 1 1 1 1 Outputs enabled 12 12.5 13 14 15 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 PARAMETER A to B CpdA (1) B to A A to B CpdB (1) B to A (1) 8 TEST CONDITIONS Outputs enabled Outputs disabled Outputs enabled Outputs disabled Outputs enabled CL = 0, f = 10 MHz, tr = tf = 1 ns UNIT pF CL = 0, f = 10 MHz, tr = tf = 1 ns pF Outputs disabled Power dissipation capacitance per transceiver Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 SN74AVC4T245 4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES576D - JUNE 2004 - REVISED SEPTEMBER 2007 PARAMETER MEASUREMENT INFORMATION 2 x VCCO S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCCO GND RL tw LOAD CIRCUIT VCCI VCCI/2 Input VCCO CL RL VTP 1.2 V 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 15 pF 15 pF 15 pF 15 pF 15 pF 2 k 2 k 2 k 2 k 2 k 0.1 V 0.1 V 0.15 V 0.15 V 0.3 V VCCI/2 0V VOLTAGE WAVEFORMS PULSE DURATION VCCA Output Control (low-level enabling) VCCA/2 VCCA/2 0V tPZL VCCI Input VCCI/2 VCCI/2 0V tPLH Output tPHL VOH VCCO/2 VOL VCCO/2 tPLZ VCCO Output Waveform 1 S1 at 2 x VCCO (see Note B) VCCO/2 VOL + VTP VOL tPZH tPHZ Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VCCO/2 VOH - VTP VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 , dv/dt 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. VCCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. Figure 1. Load and Circuit and Voltage Waveforms Submit Documentation Feedback Copyright (c) 2004-2007, Texas Instruments Incorporated Product Folder Link(s): SN74AVC4T245 9 PACKAGE OPTION ADDENDUM www.ti.com 5-Jan-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74AVC4T245DGVRE4 ACTIVE TVSOP DGV 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AVC4T245DGVRG4 ACTIVE TVSOP DGV 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AVC4T245RGYRG4 ACTIVE VQFN RGY 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 74AVC4T245RSVRG4 ACTIVE UQFN RSV 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245D ACTIVE SOIC D 16 40 CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DBR PREVIEW SSOP DB 16 2000 TBD Call TI SN74AVC4T245DE4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DGVR ACTIVE TVSOP DGV 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DRE4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245DTG4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWE4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245PWTG4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AVC4T245RGYR ACTIVE VQFN RGY 16 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) Call TI PACKAGE OPTION ADDENDUM www.ti.com 5-Jan-2010 Orderable Device Status (1) Package Type Package Drawing SN74AVC4T245RSVR ACTIVE UQFN RSV Pins Package Eco Plan (2) Qty 16 3000 Green (RoHS & no Sb/Br) Lead/Ball Finish CU NIPDAU MSL Peak Temp (3) Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74AVC4T245 : * Automotive: SN74AVC4T245-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 5-Jan-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74AVC4T245DGVR Package Package Pins Type Drawing TVSOP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DGV 16 2000 330.0 12.4 6.8 4.0 1.6 8.0 12.0 Q1 SN74AVC4T245DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN74AVC4T245PWR TSSOP PW 16 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1 SN74AVC4T245RGYR VQFN RGY 16 3000 180.0 12.4 3.8 4.3 1.5 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 5-Jan-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74AVC4T245DGVR TVSOP DGV 16 2000 346.0 346.0 29.0 SN74AVC4T245DR SOIC D 16 2500 333.2 345.9 28.6 SN74AVC4T245PWR TSSOP PW 16 2000 346.0 346.0 29.0 SN74AVC4T245RGYR VQFN RGY 16 3000 190.5 212.7 31.8 Pack Materials-Page 2 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP(R) Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee(R) Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2010, Texas Instruments Incorporated