E M C C o m p o n e n t s April 2018 Chip beads For power line MPZ series MPZ1608 MPZ1608 1608[0603 inch]* * Dimensions code JIS[EIA] type (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20180413 / beads_commercial_power_mpz1608_en.fm (3/11) E M C C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Chip beads For power line Overview of MPZ1608 type FEATURES Noise reduction solution for power line. Compared to the MMZ series, has low direct current resistance for compatibility with large currents, optimal for low power consumption. Various frequency characteristics with 5 materials of different features for countermeasures against everything from general signals to high-speed signals. Performs well even in signal lines where low direct current resistance is required. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MPZ Series name 1608 B LxWxT dimensions (mm) 1.6x0.8x0.6 1608 1.6x0.8x0.8 Material name S Y B R D 471 A Impedance () at 100MHz 260 26 471 470 Characteristic type A B T A00 Packaging style Internal code T Taping A00 AH0 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Operating Storage Type temperature temperature C C t=0.6mm -55 to +125 -55 to +125 MPZ1608 t=0.8mm -55 to +125 -55 to +125 The storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 4,000 4,000 mg 3 4 RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (4/11) E M C C o m p o n e n t s MPZ1608 type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (5/11) E M C C o m p o n e n t s MPZ1608 type MATERIAL CHARACTERISTIC B material: This type is perfectly suited for fast digital signals. By equalizing R components and X components that beads possess at a frequency of 5MHz, it is able to suppress overshooting, undershooting and ringing of fast digital signals. R material: For wide frequency applications calling for broad impedance characteristics. For digital signal line applications calling requiring good waveform integrity. Impedance values selected for effectiveness at 10 to 200MHz. S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. Y material: High frequency range type intended for the 100MHz region and above. For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for effectiveness at 80 to 400MHz. D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500 D 2000 Impedance() Y 1500 1000 R S 500 B 0 10 100 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (6/11) E M C C o m p o n e n t s MPZ1608 type SHAPE & DIMENSIONS T 0.80.15 1.60.15 Thickness(T) 0.60.15mm 0.80.15mm 0.30.2 Dimensions in mm 0.8 RECOMMENDED LAND PATTERN 0.6 0.8 0.6 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (7/11) E M C C o m p o n e n t s MPZ1608 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 470 26 30 60 100 120 180 220 330 470 600 1000 390 60 100 150 220 30 60 100 Tolerance 25% 25% 10 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 10 25% 25% DC resistance Rated current Thickness T Part No. ( )max. 0.150 0.007 0.010 0.020 0.030 0.045 0.050 0.050 0.080 0.150 0.150 0.300 0.120 0.030 0.040 0.050 0.100 0.060 0.100 0.150 (A)max. 1.0 6.0 5.0 3.5 3.0 2.0 2.0 2.2 1.7 1.0 1.0 0.8 1.2 2.3 2.0 1.8 1.5 1.8 1.2 1.0 (mm) 0.8 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 MPZ1608B471ATA00 MPZ1608S260ATAH0 MPZ1608S300ATAH0 MPZ1608S600ATAH0 MPZ1608S101ATAH0 MPZ1608S121ATAH0 MPZ1608S181ATAH0 MPZ1608S221ATA00 MPZ1608S331ATA00 MPZ1608S471ATA00 MPZ1608S601ATA00 MPZ1608S102ATA00 MPZ1608R391ATA00 MPZ1608Y600BTA00 MPZ1608Y101BTA00 MPZ1608Y151BTA00 MPZ1608Y221BTA00 MPZ1608D300BTA00 MPZ1608D600BTA00 MPZ1608D101BTA00 Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85C or more in temperature of the product. Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Yokogawa Rated current vs. temperature characteristics (derating) 7 Rated current (A) 6 5 4 3 2 1 0 -55 -35 -15 5 25 45 65 Temperature (C) 85 105 125 S260A S300A S600A S101A Y600B S221A S121A,S181A,Y101B S331A Y221B Y151B,D300B R391A,D600B B471A,S471A,S601A,D101B S102A Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (8/11) E M C C o m p o n e n t s MPZ1608 type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MPZ1608B series MPZ1608S series 500 1200 MPZ1608B471A MPZ1608S331A MPZ1608S221A MPZ1608S181A 900 MPZ1608S121A 800 MPZ1608S101A MPZ1608S600A 700 MPZ1608S260A MPZ1608S300A MPZ1608R series 500 MPZ1608S102A MPZ1608R391A 1000 300 200 400 MPZ1608S471A Impedance () Impedance () Impedance () 400 MPZ1608S601A 600 500 400 300 200 300 100 100 200 100 0 1 10 100 1000 Frequency (MHz) 0 1 10000 MPZ1608Y series 100 1000 Frequency (MHz) 600 0 1 10 100 1000 Frequency (MHz) 10000 MPZ1608D101B MPZ1608Y221B 300 500 MPZ1608Y151B Impedance () 250 MPZ1608Y101B 200 150 100 400 MPZ1608D600B 300 200 100 50 MPZ1608Y600B 0 10000 MPZ1608D series 350 Impedance () 10 1 10 100 1000 Frequency (MHz) 10000 0 1 10 MPZ1608D300B 100 1000 10000 Frequency (MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (9/11) E M C C o m p o n e n t s MPZ1608 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MPZ1608B471ATA00 MPZ1608S260ATAH0 R 100 X 10 100 1000 Frequency (MHz) 10000 MPZ1608S600ATAH0 Impedance () Impedance () Z 60 R 40 20 0 X 1 10 100 1000 Frequency (MHz) 10000 100 50 10 100 1000 Frequency (MHz) Z 10 100 1000 Frequency (MHz) MPZ1608R391ATA00 Impedance () 400 Z 300 R 100 0 X 1 10 R 100 1000 Frequency (MHz) 10000 10 100 1000 Frequency (MHz) Z 100 10000 R 50 X 800 700 600 500 400 300 200 100 0 1 140 120 100 80 60 40 20 0 0 X 1 10 100 1000 Frequency (MHz) 10000 1 10 100 1000 Frequency (MHz) 10000 450 400 350 300 250 200 150 100 50 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 MPZ1608S102ATA00 1200 1000 Z R X 10 100 1000 Frequency (MHz) 800 Z 600 R 400 200 0 10000 MPZ1608Y600BTA00 500 200 Z 50 0 10000 1 MPZ1608S331ATA00 MPZ1608S601ATA00 R X 150 10000 100 10000 X 1 100 1000 Frequency (MHz) 150 Impedance () 700 600 500 400 300 200 100 0 10 200 X MPZ1608S471ATA00 Impedance () 1 250 R R X MPZ1608S221ATA00 Z Z MPZ1608S121ATAH0 R 250 1 10000 Z 300 0 100 1000 Frequency (MHz) 40 35 30 25 20 15 10 5 0 200 300 150 Impedance () 160 140 120 100 80 60 40 20 0 Impedance () Impedance () MPZ1608S181ATAH0 200 10 MPZ1608S101ATAH0 100 80 X Impedance () 1 R Impedance () 0 Z Impedance () 200 Impedance () Z 300 40 35 30 25 20 15 10 5 0 1 X 1 10 100 1000 Frequency (MHz) 10000 MPZ1608Y101BTA00 200 Impedance () Impedance () 400 Impedance () 500 MPZ1608S300ATAH0 Z R 10 100 1000 Frequency (MHz) Z 100 R 50 X X 1 150 10000 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (10/11) E M C C o m p o n e n t s MPZ1608 type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MPZ1608Y151BTA00 MPZ1608Y221BTA00 Z 200 150 R 100 50 0 X 1 10 100 1000 Frequency (MHz) 10000 250 Z R X 1 10 100 1000 Frequency (MHz) 10000 200 150 Z 100 50 0 X 1 10 100 1000 Frequency (MHz) R 10000 MPZ1608D101BTA00 600 350 300 250 200 150 100 50 0 Impedance () Impedance () MPZ1608D600BTA00 350 300 250 200 150 100 50 0 Impedance () 250 Impedance () Impedance () 300 MPZ1608D300BTA00 Z X R 500 400 200 100 0 1 10 100 1000 Frequency (MHz) 10000 Z 300 1 10 R X 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm (11/11) E M C C o m p o n e n t s MPZ1608 type PACKAGING STYLE REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm 4.00.1 B 8.00.3 2.00.05 3.50.05 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS K 4.00.1 A Dimensions in mm Type MPZ1608 160min. Drawing direction A 1.10.2 Taping B 1.90.2 K 1.1max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180413 / beads_commercial_power_mpz1608_en.fm