1/4
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.11 - Rev.C
Anti-surge Chip Resistors
ESR Series
Features
1) Exclusive resistive element pattern and laser trimming technology results
in significantly improved surge resistance characteristics.
2) 2kV to 5kV electrostatic discharge resistance.
3) Superior power ratings.
4) ROHM resistors have obtained ISO9001 / ISO / TS16949 certification.
5) Corresponds to AEC-Q200.(ESR10/18)
Products List
Limiting Element
Voltage
(V)
Maximum
Overload
Voltage
(V)
Temperature
Coefficient
(ppm /
°C
)
Resistance
Tolerance
(%)
Operating
Temperature
Range
(
°C
)
Resistance Range SeriesPart No.
Rated Power
(70
°C)
(W)
ESR01 1005
ESR03 1608
0.2 50
150
150
200
200 400
400
200
200
100
0.25
2012
3216
3225
0402
0603
0805
1206
1210
ESR10
ESR18
ESR25
0.4
0.33
0.5
−55 to +155
F(±1%)
D(±0.5%)
J(±5%)
1MΩto10Ω
10MΩ
to
1Ω
10MΩ
to
1Ω
10MΩ
to
1Ω
1MΩ
to
10Ω
1MΩ
to
10Ω
1MΩ
to
10Ω
1MΩ
to
10Ω
10MΩ
to
1ΩE24
±200
±100
±100
F(±1%)
D(±0.5%)
J(±5%)
±200
±100
±100
F(±1%)
D(±0.5%)
J(±5%)
±200
±100
±100
F(±1%)
D(±0.5%)
J(±5%)
±200
±100
±100
F(±1%)
J(±5%)±200
±100
∗Design and specifications are subject to change without notice.
Carefully check the specification sheet supplied with the product before using or ordering it.
Size
(mm) (inch)
Part Number Description
ESR
(Anti-surge chip resistors)
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Ex.) 1Ω = 1R00 ( ±1% )
1R0 ( ±5% )
10 Ω = 10R0 ( ±0.5%, ±1%
)
100 ( ±5%
)
1M Ω = 1004 ( ±0.5%, ±1%
)
105 ( ±5%
)
01 (1005 [0402])
03 (1608 [0603])
10 (2012 [0805])
18 (3216 [1206])
25 (3225 [1210])
D ( ±0.5% )
D ( ±0.5% )
F ( ±1% )
J ( ±5% )
1 0 EPZ
SER J01 0
Paper tape
(4mm Pitch)
Packaging
specifications
MZP
Code
ESR01
Part No.
10,000
Paper tape
(4mm Pitch)
EZP
ESR03 5,000
Paper tape
(4mm Pitch)
EZP
ESR10 5,000
Paper tape
(4mm Pitch)
EZPESR18 5,000
Embossed tape
(4mm Pitch)
JZPESR25 4,000
Part No. Packaging Specifications Code
Size
(mm [inch]) Resistance
Tolerance
Nominal Resistance
D,F
J:
:4 digits
3 digits
Resistance
tolerance Resistance
code
Quantity
/ Reel
2/4
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.11 - Rev.C
Data Sheet ESR Series
Chip Resistor Dimensions and Markings
<Marking method>
There are three or four digits used for the calculation number
according to IEC code and “R”is used for the decimal point.
Part No. (mm) L W t a b Marking
existence
(Unit : mm)
∗
Only with square ma
rk
ESR01 1005 1.0±0.05 0.5±0.05 0.35±0.05 0.2±0.1 No ∗
ESR03 1608 1.6±0.1 0.8±0.1 0.45±0.1 0.3±0.2 0.3±0.2 No ∗
ESR10 2012 2.0±0.1 1.25±0.1 0.55±0.1 0.3±0.2 Yes
ESR18 3216 3.2±0.15 1.6±0.15 0.55±0.1 0.3±0.25 0.5±0.25 Yes
ESR25 3225
(inch)
0402
0603
0805
1206
1210 3.2±0.15 2.5±0.15 0.55±0.1 0.3±0.25 0.5±0.25 Yes
0.4±0.2
0.25
+0.05
−0.1
Land pattern Example
B
D
A
Land
C
Dimensions
Part No.
A
ESR01
ESR03
ESR10
ESR18
ESR25
0.5
1.0
1.2
2.2
2.2
B
1.3
2.0
2.6
4.0
4.0
C
0.5
0.8
1.15
1.5
2.3
D
0.4
0.5
0.7
0.9
0.9
(Unit : mm)
L
a
b
W
t
L
a
b
W
t
ESR01 / 03 ESR10 / 18 / 25
103
3/4
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.11 - Rev.C
Data Sheet ESR Series
Derating Curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.
ESR01 / 03 / 10 / 18 / 25
0
20
40
60
80
100
−55 0 70 100 155
AMBIENT TEMPERATURE (°C)
PERCENT RATED POWER (%)
Characteristics
Test Items Test Conditions
Resistor Type
Guaranteed Value
Endurance at 70°C
Endurance
Bend strength of
the end face plating
Resistance to solvent
± (2.0%+0.1Ω)
± (1.0%+0.05Ω)
± (3.0%+0.1Ω)
See P.1
See P.1
20°C
No remarkable abnormality on the appearance.
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
Without mechanical damage such as breaks.
Compliance Standard(s) : IEC60115−
8
JISC 5201−
8
Measurement :
+20 / −55 / +20 / +125°C
Soldering condition : 260±5°C
Duration of immersion : 10±1s
40°C, 93%RH (Relative Humidity)
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (1.0%+0.05Ω)
± (1.0%+0.05Ω)
± (1.0%+0.05Ω)
70°C
Rated voltage (current)
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
155°C
Test time : 1,000h to 1,048h
23±5°C, Immersion cleaning, 5±0.5min
Solvent : 2−propanol
EIAJ ED-4701 / 300 TEST METHOD304
Voltage : 2kV (ESR01)
3kV (ESR03 / 10 / 18)
5kV (ESR25)
C : 100pF
R : 1.5kΩ
Apply cycle : 1time
−
Static electric
characteristics ± (5.0%+0.05Ω)
Test temp. : −55°C to +125°C 5cycle
Rosin·Ethanol : 25% (Weight)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s
Rated voltage (current) ×2.0, 2s (ESR01)
Rated voltage (current) ×2.5, 2s (ESR03 / 10 / 18 / 25)
Maximum overload voltage
Variation of resistance
with temperature
Resistance
Overload
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Chip weight (typical value)
ESR01 ESR03 ESR10 ESR18 ESR25
mg/pc
Parameter Unit
0.63 2.18 5.13 9.62 16.47
Weight
4/4
www.rohm.com
○
c 2012 ROHM Co., Ltd. All rights reserved. 2012.11 - Rev.C
Data Sheet ESR Series
Tape Dimensions
Paper Tape
Embossed Tape
A0P
1
P
0
P
2
B
0
F
W
K
E
φD
0
P0
P2P1
E
FW
T2
φD0
A0
B0
Base paper
(Bottom tape)
Components Cavity
Top tape
0.7±0.1 1.2±0.1
1.1±0.1 1.9±0.1
1.65
+0.2
−0.1
2.4
+0.2
−0.1
1.95
+0.1
−0.05
3.5
+0.15
−0.05
(Unit : mm
)
WPart No. F E A
0
B
0
8.0±0.3ESR01 3.5±0.05 1.75±0.1
8.0±0.3ESR03 3.5±0.05 1.75±0.1
8.0±0.3ESR10 3.5±0.05 1.75±0.1
8.0±0.3ESR18 3.5±0.05 1.75±0.1
φ1.5
+0.1
0
φ1.5
+0.1
0
φ1.5
+0.1
0
φ1.5
+0.1
0
2.0±0.05 Max 1.1
2.0±0.05
2.0±0.05
2.0±0.05
Max 1.1
Max 1.1
Max 1.1
D
0
Part No. P
0
P
1
P
2
T
2
4.0±0.1
4.0±0.1
4.0±0.1
4.0±0.1
ESR01 2.0±0.05
ESR03 4.0±0.1
ESR10 4.0±0.1
ESR18 4.0±0.1
3.0±0.1 3.5±0.1
(Unit : mm
)
WPart No. F E A
0
B
0
D
0
P
0
P
1
P
2
K
8.0±0.3
ESR25
3.5±0.05 1.75±0.1
2.0±0.05 Max 1.14.0±0.1 4.0±0.1
φ1.5
+0.1
0
Reel Dimensions
APart No. B C D
(Unit : mm
)
φ13±0.2
ESR01
ESR03
ESR10
ESR18
ESR25
9 +1.0
0
0 2
0 4
0 6
0 8
0 2
0 4
0 6
0 8
C
ABD
φ180 0
−1.5 φ60 +1.0
0
Label
ACCORDING TO EIAJ ET-7200
B
R1120A
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
Notice
ROHM Customer Support System
http://www.rohm.com/contact/
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specied herein is subject to change for improvement without notice.
The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specied in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
