Series PVI-NPbF Photovoltaic Isolator Single and Dual Channel 5-10 Volt Output General Description The PVI Series Photovoltaic Isolator generates an electrically isolated DC voltage upon receipt of a DC input signal. It is capable of directly driving gates of power MOSFETs or IGBTs. It utilizes a monolithic integrated circuit photovoltaic generator of novel construction as its output. The output is controlled by radiation from a GaAlAs light emitting diode (LED), which is optically isolated from the photovoltaic generator. Features Isolated Voltage Source Monolithic Construction Up to 8A Output Single or Dual Output Solid-State Reliability The PVI Series is ideally suited for applications requiring high-current and/or high-voltage switching with optical isolation between the low-level driving circuitry and high-energy or high-voltage load circuits. It can be used for directly driving gates of power MOSFETs. The dual-channel device allows its outputs to drive independent discrete power MOSFETs, or be connected in parallel or in series to provide higher current drive for power MOSFETs or higher voltage drive for IGBTs. The PVI Series Photovoltaic isolators employ fast turn-off circuitry. These PVI Series Photovoltaic Isolators are packaged in 8-pin, molded DIP packages and available with either thru-hole or surface-mount (gull-wing) leads, in plastic shipping tubes. Applications 1 Load Distribution Industrial Controls Current-to-Voltage Conversion Custom Solid-State Relay www.irf.com (c) 2015 International Rectifier Part Identification PVI1050NPbF PVI5050NPbF PVI5080NPbF PVI1050NSPbF PVI5050NSPbF PVI5080NSPbF PVI1050NS-TPbF Submit Datasheet Feedback thru-hole surface-mount (gull-wing) surface-mount, tape and reel April 24, 2015 Series PVI-NPbF Electrical Specifications (-40C TA +85C unless otherwise specified) INPUT CHARACTERISTICS Input Current Range (see figure 4) Maximum Forward Voltage Drop @ 10mA, 25C (see figure 5) Maximum Reverse Voltage Maximum Reverse Current @ -6.0V (DC), 25C PVI Series Units 2.0 to 50 1.4 6.0 100 mA (DC) V (DC) V(DC) A(DC) 1.0 A(peak) PVI Series Units Maximum Pulsed Input Current @ 25C (see figure 6) OUTPUT CHARACTERISTICS Maximum Forward Voltage @ 10A 8.0 per channel V(DC) 10 A (DC) Maxiumum Reverse Current @ -10VDC COUPLED CHARACTERISTICS PVI5050N Minimum Open Circuit Voltage @ ILED = 10mA, 25C, RL = >10M (see figures 1 to 2) Minimum Short Circuit Current @ ILED = 10mA, 25C (see figures 1 to 2) Maximum Capacitance (Input/Output) PVI5080N 5.0 5.0 8.0 1.0 PVI1050N 5.0/channel 10 series 5.0 /channel 10 parallel 2.0 Units V (DC) A (DC) pF Maximum Ton Time @ ILED=10mA, CLOAD=10pF (See Figure7) RL>20M 300 RL=10M 160 S 90 S 220 S RL=4.7M Maximum Toff Time @ ILED=10mA, CLOAD=10pF (See Figure7) GENERAL CHARACTERISTICS Min. Dielectric Strength, Input-Output Min. Dielectric Strength, Output-to-Output Min. Insulation Resistance, Input-to-Output @TA=+25C, 50%RH, 100VDC Max. Pin Soldering Temperature (10 seconds max.) Ambient Temperature Range: Operating Storage PVI5050N/5080N PVI1050N 4000 2500 1200 S Units V RMS 1012 VDC +260 C -40 to +85 C -40 to +125 C International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this International Rectifier product in such applications assume all risks of such use and indemnify International Rectifier against all damages resulting from such use. 2 www.irf.com (c) 2015 International Rectifier Submit Datasheet Feedback April 24, 2015 Series PVI-NPbF 6 30 RL=10M 5 25 RL=4.7M 4 20 RL=2.2M 3 15 RL=1M 2 10 Short Circuit Current 1 5 0 0 0 2 4 6 8 10 12 14 16 18 40 Open Circuit Voltage 7 Output Voltage (VDC) 35 Output Short Circuit Current (A) 7 Output Voltage (VDC) 8 40 Open Circuit Voltage 35 6 30 RL=10M 5 25 RL=4.7M 4 20 RL=2.2M 15 3 RL=1M 2 10 Short Circuit Current 5 1 0 0 20 0 2 4 6 8 10 12 14 16 18 Output Short Circuit Current (A) 8 20 Input Current (mA) Input Current (mA) Figure 1. PVI5050N, PVI1050N Typical Output Characteristics Figure 2. PVI5080N Typical Output Characteristics 1.6 Allowable Input Current (mA) 1.8 Short Circuit Current (Isc) Normalized Output 1.4 1.2 Output Voltage (Voc) 1.0 0.8 0.6 0.4 0.2 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature (C) Figure 3. Typical Variation of Output Figure 4. Input Current Derating Input Current (mA) CAUTION: Provide current limiting so that 50mA maximum steadystate control current is not exceeded. LED Forward Voltage Drop (VDC) Figure 5. Input Characteristics 3 www.irf.com (c) 2015 International Rectifier Allowable Input Pulse Current (mA) Forced Air Temperature (C) Duty Cycle Figure 6. Input Pulse Capability Submit Datasheet Feedback April 24, 2015 Series PVI-NPbF Response Time (s) 10000 RL=10M Ton RL=4.7M 1000 RL=2.2M Toff 100 10 0 200 400 600 800 1000 Load Capacitance (pF) Figure 7. Typical Response Time Wiring Diagram Anode (+) 1 (-) 8 (-) 2 (+) 7 (+) 3 (-) 6 (-) 8 Anode (+) 2 DC Cathode Anode Cathode (-) 3 PVI5050N PVI5080N (+) 5 Cathode (-) 4 (+) 5 PVI1050N Application Note: The outputs of the PVI1050N (pins 5-6 and 7-8) may be placed in series connection to produce a 10-volt output with a 5A minimum short circuit current. Alternatively, the two ouptut of the PVI1050 may be connected in parallel to produce a 5.0-volt ouput with a 10A minimum short circuit current. The two outputs of the PVI1050N may be applied separately with a maximum 1200VDC between the outputs. Input-to-output isolation to either output is 2500V (RMS). 4 www.irf.com (c) 2015 International Rectifier Submit Datasheet Feedback April 24, 2015 Series PVI-NPbF Case Outlines PVI1050N 01-2030 01 PVI1050NS 01-2031 01 Note: For the most current drawing please refer to IR website at: http://www.irf.com/package/ 5 www.irf.com (c) 2015 International Rectifier Submit Datasheet Feedback April 24, 2015 Series PVI-NPbF Case Outlines PVI5050N/PVI5080N 01-2013 00 (MS-001AB) 01-2019 00 PVI5050NS/PVI5080NS Note: For the most current drawing please refer to IR website at: http://www.irf.com/package/ 6 www.irf.com (c) 2015 International Rectifier Submit Datasheet Feedback April 24, 2015 Series PVI-NPbF Qualification information Indusrial Qualification level (per JE DEC JE S D47I guidelines) PVI1050NPbF N/A PVI5050NPbF PVI5080NPbF Moisture Sensitivity Level PVI1050NSPbF MS L4 PVI5050NSPbF PVI5080NSPbF (per JE DE C J-S T D-020E & JE DEC J-S T D-033C ) PVI1050NS-TPbF RoHS compliant Yes Qualification standards can be found at International Rectifiers web site http://www.irf.com/product-info/reliability Applicable version of JEDEC standard at the time of product release. Revision History Date 4/24/2015 Comment * Added Qualification Information table on page 7. * Updated data sheet based on corporate template. IR WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245, USA To contact International Rectifier, please visit http://www.irf.com/whoto-call/ 7 www.irf.com (c) 2015 International Rectifier Submit Datasheet Feedback April 24, 2015