Features * Fast Read Access Time - 45 ns * Low-Power CMOS Operation * * * * * * * * - 100 A Max Standby - 20 mA Max Active at 5 MHz JEDEC Standard Packages - 28-lead PDIP - 32-lead PLCC - 28-lead TSOP and SOIC 5V 10% Supply High-Reliability CMOS Technology - 2,000V ESD Protection - 200 mA Latchup Immunity Rapid Programming Algorithm - 100 s/Byte (Typical) CMOS and TTL Compatible Inputs and Outputs Integrated Product Identification Code Industrial and Automotive Temperature Ranges Green (Pb/Halide-free) Packaging Option 512K (64K x 8) OTP EPROM AT27C512R 1. Description The AT27C512R is a low-power, high-performance 524,288-bit one-time programmable read-only memory (OTP EPROM) organized 64K by 8 bits. It requires only one 5V power supply in normal read mode operation. Any byte can be accessed in less than 45 ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems. Atmel's scaled CMOS technology provides high-speed, lower active power consumption, and significantly faster programming. Power consumption is typically only 8 mA in Active Mode and less than 10 A in Standby. The AT27C512R is available in a choice of industry-standard JEDEC-approved onetime programmable (OTP) plastic PDIP, PLCC, SOIC, and TSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. With 64K byte storage capability, the AT27C512R allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. Atmel's AT27C512R has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 s/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper programming algorithms and voltages. 0015O-EPROM-12/07 2. Pin Configurations Pin Name Function A0 - A15 Addresses O0 - O7 Outputs CE Chip Enable OE/VPP Output Enable/ Program Supply NC No Connect 2.1 28-lead PDIP/SOIC Top View A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 O0 O1 O2 GND 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC A14 A13 A8 A9 A11 OE/VPP A10 CE O7 O6 O5 O4 O3 28-lead TSOP Top View - Type 1 OE/VPP A11 A9 A8 A13 A14 VCC A15 A12 A7 A6 A5 A4 A3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 A10 CE O7 O6 O5 O4 O3 GND O2 O1 O0 A0 A1 A2 32-lead PLCC Top View 29 28 27 26 25 24 23 22 21 14 15 16 17 18 19 20 5 6 7 8 9 10 11 12 13 A8 A9 A11 NC OE/VPP A10 CE O7 O6 O1 O2 GND NC O3 O4 O5 A6 A5 A4 A3 A2 A1 A0 NC O0 4 3 2 1 32 31 30 A7 A12 A15 NC VCC A14 A13 2.2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 2.3 Note: 2 PLCC Package Pins 1 and 17 are Don't Connect. AT27C512R 0015O-EPROM-12/07 AT27C512R 3. System Considerations Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed datasheet limits, resulting in device non-conformance. At a minimum, a 0.1 F high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 F bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. 4. Block Diagram 5. Absolute Maximum Ratings* Temperature Under Bias............................... -55C to + 125C Storage Temperature .................................... -65C to + 150C Voltage on Any Pin with Respect to Ground ........................................-2.0V to + 7.0V(1) Voltage on A9 with Respect to Ground .....................................-2.0V to + 14.0V(1) *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. VPP Supply Voltage with Respect to Ground ......................................-2.0V to + 14.0V(1) Note: 1. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V DC which may overshoot to +7.0 volts for pulses of less than 20 ns. 3 0015O-EPROM-12/07 6. Operating Modes Mode/Pin CE OE/VPP Ai Outputs Read VIL VIL Ai DOUT Output Disable (1) VIL VIH X High Z Standby VIH (1) X X High Z Rapid Program(2) VIL VPP Ai DIN PGM Inhibit VIH VPP X High Z =VH(3) Product Identification(4) Notes: (1) VIL A9 A0 = VIH or VIL A1 - A15 = VIL VIL Identification Code 1. X can be VIL or VIH. 2. Refer to Programming Characteristics. 3. VH = 12.0 0.5V. 4. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled low (VIL) to select the Manufacturer's Identification byte and high (VIH) to select the Device Code byte. 7. DC and AC Operating Conditions for Read Operation AT27C512R Ind. -45 -70 -40C - 85C -40C - 85C Operating Temp.(Case) Auto. -40 C - 125 C VCC Supply 5V 10% 5V 10% 8. DC and Operating Characteristics for Read Operation Symbol Parameter Condition ILI Input Load Current VIN = 0V to VCC ILO Output Leakage Current ISB VCC(1) Standby Current ICC VCC Active Current VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 A Note: 4 Max Units Ind. 1 A Auto. 5 A Ind. 5 A Auto. 10 A 100 A ISB2 (TTL), CE = 2.0 to VCC + 0.5V 1 mA f = 5 MHz, IOUT = 0 mA, CE = VIL 20 mA -0.6 0.8 V 2.0 VCC + 0.5 V 0.4 V VOUT = 0V to VCC Min ISB1 (CMOS), CE = VCC 0.3V 2.4 V 1. VCC must be applied simultaneously with or before OE/VPP, and removed simultaneously with or after OE/VPP.. AT27C512R 0015O-EPROM-12/07 AT27C512R 9. AC Characteristics for Read Operation AT27C512R -45 Symbol Parameter Condition tACC(1) Address to Output Delay CE = OE/VPP = VIL tCE(1) CE to Output Delay tOE(1) OE/VPP to Output Delay tDF(1) OE/VPP or CE High to Output Float, Whichever Occurred First tOH Output Hold from Address, CE or OE/VPP, Whichever Occurred First Note: Min -70 Max Max Units 45 70 ns OE/VPP = VIL 45 70 ns CE = VIL 20 30 ns 20 25 ns 7 Min 7 ns 1. See AC Waveforms for Read Operation. 10. AC Waveforms for Read Operation(1) Notes: 1. Timing measurement reference level is 1.5V for -45 devices. Input AC drive levels are VIL = 0.0V and VIH = 3.0V. Timing measurement reference levels for all other speed grades are VOL = 0.8V and VOH = 2.0V. Input AC drive levels are VIL = 0.45V and VIH = 2.4V. 2. OE/VPP may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE. 3. OE/VPP may be delayed up to tACC - tOE after the address is valid without impact on tACC. 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 5 0015O-EPROM-12/07 11. Input Test Waveforms and Measurement Levels For -45 devices only: tR, tF < 5 ns (10% to 90%) For -70 devices: tR, tF < 20 ns (10% to 90%) 12. Output Test Load Note: 1. CL = 100 pF including jig capacitance, except for the -45 devices, where CL = 30 pF. 13. Pin Capacitance f = 1 MHz, T = 25C (1) Symbol CIN COUT Note: 6 Typ Max Units Conditions 4 6 pF VIN = 0V 8 12 pF VOUT = 0V 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C512R 0015O-EPROM-12/07 AT27C512R 14. Programming Waveforms(1) Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer. 15. DC Programming Characteristics TA = 25 5C, VCC = 6.5 0.25V, OE/VPP = 13.0 0.25V Limits Symbol Parameter Test Conditions ILI Input Load Current VIN = VIL,VIH VIL Input Low Level VIH Input High Level VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 A ICC2 VCC Supply Current (Program and Verify) IPP2 OE/VPP Current VID A9 Product Identification Voltage Min Max Units 10 A -0.6 0.8 V 2.0 VCC + 1 V 0.4 V 2.4 CE = VIL 11.5 V 25 mA 25 mA 12.5 V 7 0015O-EPROM-12/07 16. AC Programming Characteristics TA = 25 5C, VCC = 6.5 0.25V, OE/VPP = 13.0 0.25V Limits Test Conditions(1) Symbol Parameter tAS Address Setup Time 2 s tOES OE/VPP Setup Time 2 s tOEH OE/VPP Hold Time 2 s tDS Data Setup Time 2 s tAH Address Hold Time 0 s tDH Data Hold Time 2 s Input Rise and Fall Times (10% to 90%) 20 ns Input Pulse Levels 0.45V to 2.4V (2) CE High to Output Float Delay tDFP VCC Setup Time tPW CE Program Pulse Width(3) Max 0 Input Timing Reference Level 0.8V to 2.0V tVCS tVR OE/VPP Recovery Time tPRT OE/VPP Pulse Rise Time During Programming ns 2 Output Timing Reference Level 0.8V to 2.0V Data Valid from CE Units 130 s 95 (2) tDV Notes: Min 105 s 1 s 2 s 50 ns 1. VCC must be applied simultaneously or before OE/VPP and removed simultaneously or after OE/VPP. 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven - see timing diagram. 3. Program Pulse width tolerance is 100 sec 5%. 17. Atmel's AT27C512R Integrated Product Identification Code Pins A0 O7 O6 O5 O4 O3 O2 O1 O0 Hex Data Manufacturer 0 0 0 0 1 1 1 1 0 1E Device Type 1 0 0 0 0 1 1 0 1 0D Codes 8 AT27C512R 0015O-EPROM-12/07 AT27C512R 18. Rapid Programming Algorithm A 100 s CE pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and OE/VPP is raised to 13.0V. Each address is first programmed with one 100 s CE pulse without verification. Then a verification/reprogramming loop is executed for each address. In the event a byte fails to pass verification, up to 10 successive 100 s pulses are applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been applied, the part is considered failed. After the byte verifies properly, the next address is selected until all have been checked. OE/VPP is then lowered to VIL and VCC to 5.0V. All bytes are read again and compared with the original data to determine if the device passes or fails. 9 0015O-EPROM-12/07 19. Ordering Information 19.1 Standard Package ICC (mA) tACC (ns) Active Standby Ordering Code Package 45 20 0.1 AT27C512R-45JI AT27C512R-45PI AT27C512R-45RI AT27C512R-45TI 32J 28P6 28R(1) 28T Industrial (-40 C to 85 C) 70 20 0.1 AT27C512R-70JI AT27C512R-70PI AT27C512R-70RI AT27C512R-70TI 32J 28P6 28R(1) 28T Industrial (-40 C to 85 C) 20 0.1 AT27C512R-70JA AT27C512R-70PA AT27C512R-70RA 32J 28P6 28R(1) Automotive (-40 C to 125 C) Ordering Code Package Operation Range Note: 19.2 Operation Range Not recommended for new designs. Use Green package option. Green Package (Pb/Halide-free) ICC (mA) tACC (ns) Active Standby 45 20 0.1 AT27C512R-45JU AT27C512R-45PU AT27C512R-45RU AT27C512R-45TU 32J 28P6 28R(1) 28T Industrial (-40 C to 85 C) 70 20 0.1 AT27C512R-70JU AT27C512R-70PU AT27C512R-70RU AT27C512R-70TU 32J 28P6 28R(1) 28T Industrial (-40 C to 85 C) Note: 1. The 28-pin SOIC package is not recommended for new designs. Package Type 32J 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) 28P6 28-Lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) 28R 28-Lead, 0.330" Wide, Plastic Gull Wing Small Outline (SOIC) 28T 28-Lead, Thin Small Outline Package (TSOP) 10 AT27C512R 0015O-EPROM-12/07 AT27C512R Packaging Information 19.3 32J - PLCC 1.14(0.045) X 45 PIN NO. 1 IDENTIFIER 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) E1 E2 B1 E B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) D2 Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 3.175 - 3.556 A1 1.524 - 2.413 A2 0.381 - - D 12.319 - 12.573 D1 11.354 - 11.506 D2 9.906 - 10.922 E 14.859 - 15.113 E1 13.894 - 14.046 E2 12.471 - 13.487 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 32J B 11 0015O-EPROM-12/07 19.4 28P6 - PDIP D PIN 1 E1 A SEATING PLANE A1 L B B1 e E 0 ~ 15 C COMMON DIMENSIONS (Unit of Measure = mm) REF MIN NOM MAX A - - 4.826 A1 0.381 - - D 36.703 - 37.338 E 15.240 - 15.875 E1 13.462 - 13.970 B 0.356 - 0.559 B1 1.041 - 1.651 L 3.048 - 3.556 C 0.203 - 0.381 eB 15.494 - 17.526 SYMBOL eB Notes: 1. This package conforms to JEDEC reference MS-011, Variation AB. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). e NOTE Note 2 Note 2 2.540 TYP 09/28/01 R 12 2325 Orchard Parkway San Jose, CA 95131 TITLE 28P6, 28-lead (0.600"/15.24 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 28P6 REV. B AT27C512R 0015O-EPROM-12/07 AT27C512R 19.5 28R - SOIC B E E1 PIN 1 e D A A1 COMMON DIMENSIONS (Unit of Measure = mm) 0 ~ 8 C L Note: 1. Dimensions D and E1 do not include mold Flash or protrusion. Mold Flash or protrusion shall not exceed 0.25 mm (0.010"). SYMBOL MIN NOM MAX A 2.39 - 2.79 A1 0.050 - 0.356 D 18.00 - 18.50 E 11.70 - 12.50 E1 8.59 - 8.79 B 0.356 - 0.508 C 0.203 - 0.305 L 0.94 - 1.27 e NOTE Note 1 Note 1 1.27 TYP 5/18/2004 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 28R, 28-lead, 0.330" Body Width, Plastic Gull Wing Small Outline (SOIC) DRAWING NO. REV. 28R C 13 0015O-EPROM-12/07 19.6 28T - TSOP PIN 1 0 ~ 5 c Pin 1 Identifier Area D1 D L b e L1 A2 E A GAGE PLANE SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) A1 MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.90 1.00 1.05 D 13.20 13.40 13.60 D1 11.70 11.80 11.90 Note 2 E 7.90 8.00 8.10 Note 2 L 0.50 0.60 0.70 SYMBOL Notes: 1. This package conforms to JEDEC reference MO-183. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. L1 NOTE 0.25 BASIC b 0.17 0.22 0.27 c 0.10 - 0.21 e 0.55 BASIC 12/06/02 R 14 2325 Orchard Parkway San Jose, CA 95131 TITLE 28T, 28-lead (8 x 13.4 mm) Plastic Thin Small Outline Package, Type I (TSOP) DRAWING NO. REV. 28T C AT27C512R 0015O-EPROM-12/07 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support eprom@atmel.com Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2007 Atmel Corporation. All rights reserved. Atmel(R), logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 0015O-EPROM-12/07