SLAS231B - JUNE 1999 - REVISED APRIL 2004 D 8-Bit Voltage Output DAC D Programmable Settling Time vs Power D D D D D Buffered High-Impedance Reference Input D Monotonic Over Temperature D Available in MSOP Package Consumption 3 s in Fast Mode 9 s in Slow Mode Ultra Low Power Consumption: 900 W Typ in Slow Mode at 3 V 2.1 mW Typ in Fast Mode at 3 V Differential Nonlinearity . . . <0.2 LSB Compatible With TMS320 and SPI Serial Ports Power-Down Mode applications D D D D D Digital Servo Control Loops Digital Offset and Gain Adjustment Industrial Process Control Machine and Motion Control Devices Mass Storage Devices D OR DGK PACKAGE (TOP VIEW) description The TLV5623 is a 8-bit voltage output digital-toanalog converter (DAC) with a flexible 4-wire serial interface. The 4-wire serial interface allows glueless interface to TMS320, SPI, QSPI, and Microwire serial ports. The TLV5623 is programmed with a 16-bit serial string containing 4 control and 8 data bits. Developed for a wide range of supply voltages, the TLV5623 can operate from 2.7 V to 5.5 V. DIN SCLK CS FS 1 8 2 7 3 6 4 5 VDD OUT REFIN AGND The resistor string output voltage is buffered by a x2 gain rail-to-rail output buffer. The buffer features a Class AB output stage to improve stability and reduce settling time. The settling time of the DAC is programmable to allow the designer to optimize speed versus power dissipation. The settling time is chosen by the control bits within the 16-bit serial input string. A high-impedance buffer is integrated on the REFIN terminal to reduce the need for a low source impedance drive to the terminal. Implemented with a CMOS process, the TLV5623 is designed for single supply operation from 2.7 V to 5.5 V. The device is available in an 8-terminal SOIC package. The TLV5623C is characterized for operation from 0C to 70C. The TLV5623I is characterized for operation from - 40C to 85C. AVAILABLE OPTIONS TA PACKAGE SMALL OUTLINE (D) 0C to 70C TLV5623CD -40C to 85C TLV5623ID MSOP (DGK) TLV5623CDGK TLV5623IDGK Available in tape and reel as the TLV5623CDR and the TLV5623IDR Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002 - 2004, Texas Instruments Incorporated !"#$ % &'!!($ #% )'*+&#$ ,#$( !,'&$% &!" $ %)(&&#$% )(! $-( $(!"% (.#% %$!'"($% %$#,#!, /#!!#$0 !,'&$ )!&(%%1 ,(% $ (&(%%#!+0 &+',( $(%$1 #++ )#!#"($(!% WWW.TI.COM 1 SLAS231B - JUNE 1999 - REVISED APRIL 2004 functional block diagram _ 6 + REFIN 10 Serial Input Register 1 DIN 8 8-Bit Data Latch 2 SCLK 16 Cycle Timer 3 CS 4 FS 8 x2 7 OUT Update 2 Power-On Reset Speed/Power-Down Logic Terminal Functions TERMINAL NAME 2 NO. I/O DESCRIPTION AGND 5 Analog ground CS 3 I Chip select. Digital input used to enable and disable inputs, active low. DIN 1 I Serial digital data input FS 4 I Frame sync. Digital input used for 4-wire serial interfaces such as the TMS320 DSP interface. OUT 7 O DAC analog output REFIN 6 I Reference analog input voltage SCLK 2 I Serial digital clock input VDD 8 Positive power supply WWW.TI.COM SLAS231B - JUNE 1999 - REVISED APRIL 2004 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage (VDD to AGND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Reference input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.3 V to VDD + 0.3 V Digital input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.3 V to VDD + 0.3 V Operating free-air temperature range, TA: TLV5623C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C TLV5623I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to 85C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions Supply voltage, VDD VDD = 5 V VDD = 3 V High-level digital input voltage, VIH DVDD = 2.7 V DVDD = 5.5 V Low-level digital input voltage, VIL DVDD = 2.7 V DVDD = 5.5 V Reference voltage, Vref to REFIN terminal Reference voltage, Vref to REFIN terminal MIN NOM MAX 4.5 5 5.5 V 2.7 3 3.3 V 2 V 2.4 VDD = 5 V (see Note 1) VDD = 3 V (see Note 1) V AGND 2.048 AGND 1.024 2 10 Load resistance, RL UNIT 0.6 V 1 V VDD -1.5 VDD -1.5 V V k Load capacitance, CL 100 pF Clock frequency, fCLK 20 MHz 0 70 C -40 85 C Operating free-air temperature, TA TLV5623C TLV5623I NOTE 1: Due to the x2 output buffer, a reference input voltage VDD/2 causes clipping of the transfer function. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) power supply PARAMETER IDD TEST CONDITIONS VDD = 5 V, VREF = 2.048 V, No load, All inputs = AGND or VDD, DAC latch = 0x800 Power supply current VDD = 3 V, VREF = 1.024 V No load, All inputs = AGND or VDD, DAC latch = 0x800 MIN TYP MAX UNIT Fast 0.9 1.35 mA Slow 0.4 0.6 mA Fast 0.7 1.1 mA Slow 0.3 0.45 mA Power down supply current (see Figure 12) PSRR Power supply rejection ratio 1 Zero scale See Note 2 -68 Full scale See Note 3 -68 Power on threshold voltage, POR 2 A dB V NOTES: 2. Power supply rejection ratio at zero scale is measured by varying VDD and is given by: PSRR = 20 log [(EZS(VDDmax) - EZS(VDDmin))/VDDmax] 3. Power supply rejection ratio at full scale is measured by varying VDD and is given by: PSRR = 20 log [(EG(VDDmax) - EG(VDDmin))/VDDmax] WWW.TI.COM 3 SLAS231B - JUNE 1999 - REVISED APRIL 2004 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) (continued) static DAC specifications RL = 10 k, CL = 100 pF PARAMETER TEST CONDITIONS MIN Resolution TYP MAX UNIT 8 bits INL Integral nonlinearity See Note 4 0.3 0.5 LSB DNL Differential nonlinearity See Note 5 0.07 0.2 LSB EZS EZS TC Zero-scale error (offset error at zero scale) See Note 6 Zero-scale-error temperature coefficient See Note 7 EG Gain error See Note 8 Gain-error temperature coefficient See Note 9 10 10 mV ppm/C 0.6 10 % of FS voltage ppm/C NOTES: 4. The relative accuracy or integral nonlinearity (INL) sometimes referred to as linearity error, is the maximum deviation of the output from the line between zero and full scale excluding the effects of zero code and full-scale errors. Tested from code 10 to code 255. 5. The differential nonlinearity (DNL) sometimes referred to as differential error, is the difference between the measured and ideal 1 LSB amplitude change of any two adjacent codes. Monotonic means the output voltage changes in the same direction (or remains constant) as a change in the digital input code. Tested from code 10 to code 255. 6. Zero-scale error is the deviation from zero voltage output when the digital input code is zero. 7. Zero-scale-error temperature coefficient is given by: EZS TC = [EZS (Tmax) - EZS (Tmin)]/Vref x 106/(Tmax - Tmin). 8. Gain error is the deviation from the ideal output (2Vref - 1 LSB) with an output load of 10 k excluding the effects of the zero-error. 9. Gain temperature coefficient is given by: EG TC = [EG(Tmax) - EG (Tmin)]/Vref x 106/(Tmax - Tmin). output specifications PARAMETER VO TEST CONDITIONS Voltage output range MIN RL = 10 k Output load regulation accuracy TYP 0 MAX VDD-0.1 0.1 RL = 2 k, vs 10 k 0.25 UNIT V % of FS voltage reference input (REF) PARAMETER VI RI Input voltage range CI Input capacitance TEST CONDITIONS MIN TYP 0 MAX VDD-1.5 Input resistance 10 Reference input bandwidth REFIN = 0.2 Vpp + 1.024 V dc Reference feed through REFIN = 1 Vpp at 1 kHz + 1.024 V dc (see Note 10) UNIT V M 5 pF Slow 525 kHz Fast 1.3 MHz -75 dB NOTE 10: Reference feedthrough is measured at the DAC output with an input code = 0x000. digital inputs PARAMETER IIH IIL High-level digital input current CI Input capacitance 4 Low-level digital input current TEST CONDITIONS MIN TYP VI = VDD VI = 0 V 3 WWW.TI.COM MAX UNIT 1 A 1 A pF SLAS231B - JUNE 1999 - REVISED APRIL 2004 operating characteristics over recommended operating free-air temperature range (unless otherwise noted) analog output dynamic performance PARAMETER TEST CONDITIONS ts(FS) Output settling time, full scale RL = 10 k, See Note 11 CL = 100 pF, ts(CC) Output settling time, code to code RL = 10 k, See Note 12 CL = 100 pF, SR S/N Slew rate RL = 10 k, See Note 13 CL = 100 pF, Glitch energy Code transition from 0x7F0 to 0x800 MIN TYP MAX Fast 3 5.5 Slow 9 20 Fast 1 s Slow 2 s Fast 3.6 Slow 0.9 Signal to noise S/(N+D) Signal to noise + distortion THD Total harmonic distortion fs = 400 KSPS fout = 1.1 kHz, RL = 10 k, CL = 100 pF, k BW = 20 kHz Spurious free dynamic range UNIT ss V/ s V/s 10 nV-s 57 dB 49 dB -50 dB 60 dB NOTES: 11. Settling time is the time for the output signal to remain within 0.5 LSB of the final measured value for a digital input code change of 0x020 to 0xFF0 or 0xFF0 to 0x020. Not tested, ensured by design. 12. Settling time is the time for the output signal to remain within 0.5 LSB of the final measured value for a digital input code change of one count. Not tested, ensured by design. 13. Slew rate determines the time it takes for a change of the DAC output from 10% to 90% full-scale voltage. digital input timing requirements MIN tsu(CS-FS) tsu(FS-CK) Setup time, CS low before FS Setup time, FS low before first negative SCLK edge NOM MAX UNIT 10 ns 8 ns tsu(C16-FS) Setup time, sixteenth negative edge after FS low on which bit D0 is sampled before rising edge of FS 10 ns tsu(C16-CS) Setup time, sixteenth positive SCLK edge (first positive after D0 is sampled) before CS rising edge. If FS is used instead of the sixteenth positive edge to update the DAC, then the setup time is between the FS rising edge and CS rising edge. 10 ns twH twL Pulse duration, SCLK high 25 ns Pulse duration, SCLK low 25 ns tsu(D) Setup time, data ready before SCLK falling edge 8 ns th(D) twH(FS) Hold time, data held valid after SCLK falling edge 5 ns 20 ns Pulse duration, FS high WWW.TI.COM 5 SLAS231B - JUNE 1999 - REVISED APRIL 2004 PARAMETER MEASUREMENT INFORMATION IIIII IIIII IIII IIII SCLK 1 2 tsu(D) DIN twH twL 3 4 5 15 16 th(D) D15 D14 D13 D12 tsu(FS-CK) D1 D0 tsu(C16-CS) tsu(CS-FS) CS twH(FS) tsu(C16-FS) FS Figure 1. Timing Diagram 6 III III IIII IIII WWW.TI.COM SLAS231B - JUNE 1999 - REVISED APRIL 2004 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs LOAD CURRENT OUTPUT VOLTAGE vs LOAD CURRENT 2.004 3 V Slow Mode, SOURCE 3 V Fast Mode, SOURCE 2 1.998 1.996 1.994 5 V Slow Mode, SOURCE 4.005 VO - Output Voltage - V VO - Output Voltage - V 2.002 4.01 VDD = 3 V, Vref = 1 V, Full Scale 1.992 4 5 V Fast Mode, SOURCE 3.995 3.99 3.985 3.98 1.990 3.975 0 0.01 0.02 0.05 0.1 0.2 0.5 Load Current - mA 1 2 0 0.02 0.04 0.1 0.2 0.4 1 Load Current - mA Figure 2 2 4 Figure 3 OUTPUT VOLTAGE vs LOAD CURRENT OUTPUT VOLTAGE vs LOAD CURRENT 0.2 0.35 VDD = 3 V, Vref = 1 V, Zero Code 0.18 VDD = 5 V, Vref = 2 V, Zero Code 0.3 0.16 0.14 VO - Output Voltage - V VO - Output Voltage - V VDD = 5 V, Vref = 2 V, Full Scale 3 V Slow Mode, SINK 0.12 0.1 0.08 3 V Fast Mode, SINK 0.06 0.25 5 V Slow Mode, SINK 0.2 0.15 5 V Fast Mode, SINK 0.1 0.04 0.05 0.02 0 0 0 0.01 0.02 0.05 0.1 0.2 0.5 Load Current - mA 1 2 0 Figure 4 0.02 0.04 0.1 0.2 0.4 1 Load Current - mA 2 4 Figure 5 WWW.TI.COM 7 SLAS231B - JUNE 1999 - REVISED APRIL 2004 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 1 1 VDD = 5 V, Vref = 2 V, Full Scale I DD - Supply Current - mA I DD - Supply Current - mA VDD = 3 V, Vref = 1 V, Full Scale 0.8 Fast Mode 0.6 0.4 Fast Mode 0.8 0.6 0.4 Slow Mode Slow Mode 0.2 -55 -40 85 -25 0 25 40 70 TA - Free-Air Temperature - C 0.2 -55 -40 125 Figure 6 TOTAL HARMONIC DISTORTION vs FREQUENCY 0 0 Vref = 1 V dc + 1 V p/p Sinewave, Output Full Scale -10 THD - Total Harmonic Distortion - dB THD - Total Harmonic Distortion - dB 125 Figure 7 TOTAL HARMONIC DISTORTION vs FREQUENCY -20 -30 --40 -50 -60 Fast Mode -70 -80 0 5 10 20 30 50 100 f - Frequency - kHz Vref = 1 V dc + 1 V p/p Sinewave, Output Full Scale -10 -20 -30 --40 -50 -60 Slow Mode -70 -80 0 5 10 20 30 f - Frequency - kHz Figure 8 8 85 -25 0 25 40 70 TA - Free-Air Temperature - C Figure 9 WWW.TI.COM 50 100 SLAS231B - JUNE 1999 - REVISED APRIL 2004 TYPICAL CHARACTERISTICS Vref = 1 V dc + 1 V p/p Sinewave, Output Full Scale -10 TOTAL HARMONIC DISTORTION AND NOISE vs FREQUENCY THD - Total Harmonic Distortion And Noise - dB 0 -20 -30 --40 -50 Fast Mode -60 -70 -80 0 Vref = 1 V dc + 1 V p/p Sinewave, Output Full Scale -10 -20 -30 --40 -50 Slow Mode -60 -70 -80 0 5 10 30 20 50 100 0 5 f - Frequency - kHz 10 20 30 50 100 f - Frequency - kHz Figure 10 Figure 11 SUPPLY CURRENT vs TIME (WHEN ENTERING POWER-DOWN MODE) 900 800 I DD - Supply Current - A THD - Total Harmonic Distortion And Noise - dB TOTAL HARMONIC DISTORTION AND NOISE vs FREQUENCY 700 600 500 400 300 200 100 0 0 100 200 300 400 500 600 700 800 900 1000 T - Time - ns Figure 12 WWW.TI.COM 9 SLAS231B - JUNE 1999 - REVISED APRIL 2004 TYPICAL CHARACTERISTICS DNL - Differential Nonlinearity - LSB DIFFERENTIAL NONLINEARITY vs DIGITAL OUTPUT CODE 0.10 0.08 0.06 0.04 0.02 0.00 -0.02 -0.04 -0.06 -0.08 -0.10 0 64 128 192 255 Digital Output Code Figure 13 INL - Integral Nonlinearity - LSB INTEGRAL NONLINEARITY vs DIGITAL OUTPUT CODE 0.5 0.4 0.3 0.2 0.1 -0.0 -0.1 -0.2 -0.3 -0.4 -0.5 0 64 128 Digital Output Code Figure 14 10 WWW.TI.COM 192 255 SLAS231B - JUNE 1999 - REVISED APRIL 2004 APPLICATION INFORMATION general function The TLV5623 is an 8-bit single supply DAC based on a resistor string architecture. The device consists of a serial interface, speed and power-down control logic, a reference input buffer, a resistor string, and a rail-to-rail output buffer. The output voltage (full scale determined by external reference) is given by: 2 REF CODE [V] 2n where REF is the reference voltage and CODE is the digital input value within the range of 010 to 2n-1, where n = 8 (bits). The 16-bit data word, consisting of control bits and the new DAC value, is illustrated in the data format section. A power-on reset initially resets the internal latches to a defined state (all bits zero). serial interface The device has to be enabled with CS set to low. A falling edge of FS starts shifting the data bit-per-bit (starting with the MSB) to the internal register on the falling edges of SCLK. After 16 bits have been transferred or FS rises, the content of the shift register is moved to the DAC latch, which updates the voltage output to the new level. The serial interface of the TLV5623 can be used in two basic modes: D Four wire (with chip select) D Three wire (without chip select) Using chip select (four-wire mode), it is possible to have more than one device connected to the serial port of the data source (DSP or microcontroller). The interface is compatible with the TMS320 family. Figure 15 shows an example with two TLV5623s connected directly to a TMS320 DSP. TLV5623 CS FS DIN SCLK TLV5623 CS FS DIN SCLK TMS320 DSP XF0 XF1 FSX DX CLKX Figure 15. TMS320 Interface WWW.TI.COM 11 SLAS231B - JUNE 1999 - REVISED APRIL 2004 APPLICATION INFORMATION serial interface (continued) If there is no need to have more than one device on the serial bus, then CS can be tied low. Figure 16 shows an example of how to connect the TLV5623 to a TMS320, SPI, or Microwire port using only three pins. TMS320 DSP TLV5623 FSX SPI FS DIN DX CLKX TLV5623 FS DIN SS MOSI SCLK SCLK Microwire FS DIN I/O SO SK SCLK CS TLV5623 SCLK CS CS Figure 16. Three-Wire Interface Notes on SPI and Microwire: Before the controller starts the data transfer, the software has to generate a falling edge on the I/O pin connected to FS. If the word width is 8 bits (SPI and Microwire), two write operations must be performed to program the TLV5623. After the write operation(s), the DAC output is updated automatically on the next positive clock edge following the sixteenth falling clock edge. serial clock frequency and update rate The maximum serial clock frequency is given by: f SCLKmax + t wH(min) 1 )t + 20 MHz wL(min) The maximum update rate is: f UPDATEmax + 1 wH(min) ) twL(min) + 1.25 MHz 16 t The maximum update rate is a theoretical value for the serial interface, since the settling time of the TLV5623 has to be considered also. data format The 16-bit data word for the TLV5623 consists of two parts: D Control bits D New DAC value D15 D14 D13 D12 X SPD PWR X X: don't care SPD: Speed control bit. PWR: Power control bit. (D15 . . . D12) (D11 . . . D0) D11 1 fast mode 1 power down D10 D9 D8 D7 D6 D5 New DAC value (8 bits) 0 slow mode 0 normal operation In power-down mode, all amplifiers within the TLV5623 are disabled. 12 WWW.TI.COM D4 D3 D2 D1 D0 0 0 0 0 SLAS231B - JUNE 1999 - REVISED APRIL 2004 APPLICATION INFORMATION TLV5623 interfaced to TMS320C203 DSP hardware interfacing Figure 17 shows an example how to connect the TLV5623 to a TMS320C203 DSP. The serial interface of the TLV5623 is ideally suited to this configuration, using a maximum of four wires to make the necessary connections. In applications where only one synchronous serial peripheral is used, the interface can be simplified even further by pulling CS low all the time as shown in the figure. TMS320C203 TLV5623 FS FS DX DIN VDD SCLK CLKX OUT REFIN REF CS AGND RLOAD Figure 17. TLV5623 to DSP Interface TLV5623 interfaced to MCS51 microcontroller hardware interfacing Figure 18 shows an example of how to connect the TLV5623 to an MCS51 compatible microcontroller. The serial DAC input data and external control signals are sent via I/O port 3 of the controller. The serial data is sent on the RxD line, with the serial clock output on the TxD line. P3.4 and P3.5 are configured as outputs to provide the chip select and frame sync signals for the TLV5623. MCS51 Controller TLV5623 RxD SDIN TxD SCLK P3.4 P3.5 CS FS VDD OUT REF REFIN RLOAD AGND Figure 18. TLV5623 to MCS51 Controller Interface MCS is a registered trademark of Intel Corporation WWW.TI.COM 13 SLAS231B - JUNE 1999 - REVISED APRIL 2004 APPLICATION INFORMATION linearity, offset, and gain error using single ended supplies When an amplifier is operated from a single supply, the voltage offset can still be either positive or negative. With a positive offset, the output voltage changes on the first code change. With a negative offset, the output voltage may not change with the first code, depending on the magnitude of the offset voltage. The output amplifier attempts to drive the output to a negative voltage. However, because the most negative supply rail is ground, the output cannot drive below ground and clamps the output at 0 V. The output voltage then remains at zero until the input code value produces a sufficient positive output voltage to overcome the negative offset voltage, resulting in the transfer function shown in Figure 19. Output Voltage 0V DAC Code Negative Offset Figure 19. Effect of Negative Offset (single supply) This offset error, not the linearity error, produces this breakpoint. The transfer function would have followed the dotted line if the output buffer could drive below the ground rail. For a DAC, linearity is measured between zero-input code (all inputs 0) and full-scale code after offset and full scale are adjusted out or accounted for in some way. However, single supply operation does not allow for adjustment when the offset is negative due to the breakpoint in the transfer function. So the linearity is measured between full-scale code and the lowest code that produces a positive output voltage. power-supply bypassing and ground management Printed-circuit boards that use separate analog and digital ground planes offer the best system performance. Wire-wrap boards do not perform well and should not be used. The two ground planes should be connected together at the low-impedance power-supply source. The best ground connection may be achieved by connecting the DAC AGND terminal to the system analog ground plane, making sure that analog ground currents are well managed and there are negligible voltage drops across the ground plane. A 0.1-F ceramic-capacitor bypass should be connected between VDD and AGND and mounted with short leads as close as possible to the device. Use of ferrite beads may further isolate the system analog supply from the digital power supply. Figure 20 shows the ground plane layout and bypassing technique. Analog Ground Plane 1 8 2 7 3 6 4 5 0.1 F Figure 20. Power-Supply Bypassing 14 WWW.TI.COM SLAS231B - JUNE 1999 - REVISED APRIL 2004 APPLICATION INFORMATION definitions of specifications and terminology integral nonlinearity (INL) The relative accuracy or integral nonlinearity (INL), sometimes referred to as linearity error, is the maximum deviation of the output from the line between zero and full scale excluding the effects of zero code and full-scale errors. differential nonlinearity (DNL) The differential nonlinearity (DNL), sometimes referred to as differential error, is the difference between the measured and ideal 1 LSB amplitude change of any two adjacent codes. Monotonic means the output voltage changes in the same direction (or remains constant) as a change in the digital input code. zero-scale error (EZS) Zero-scale error is defined as the deviation of the output from 0 V at a digital input value of 0. gain error (EG) Gain error is the error in slope of the DAC transfer function. signal-to-noise ratio + distortion (S/N+D) S/N+D is the ratio of the rms value of the output signal to the rms sum of all other spectral components below the Nyquist frequency, including harmonics but excluding dc. The value for S/N+D is expressed in decibels. spurious free dynamic range (SFDR) SFDR is the difference between the rms value of the output signal and the rms value of the largest spurious signal within a specified bandwidth. The value for SFDR is expressed in decibels. total harmonic distortion (THD) THD is the ratio of the rms sum of the first six harmonic components to the rms value of the fundamental signal and is expressed in decibels. WWW.TI.COM 15 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device (1) Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TLV5623CD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623CDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623CDGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623CDGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623CDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623CDGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623CDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623IDGK ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623IDGKG4 ACTIVE VSSOP DGK 8 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623IDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623IDGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TLV5623IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLV5623IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM The marketing status values are defined as follows: Addendum-Page 1 (3) Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TLV5623CDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TLV5623IDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TLV5623IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLV5623CDGKR VSSOP DGK 8 2500 367.0 367.0 35.0 TLV5623IDGKR VSSOP DGK 8 2500 367.0 367.0 35.0 TLV5623IDR SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated