SM15T39CA/9T - Vishay Semiconductors

SM15T Series

www.vishay.com Vishay General Semiconductor

Revision: 16-Jan-18 1Document Number: 88380

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Surface Mount TRANSZORB® Transient Voltage Suppressors

DEVICES FOR BI-DIRECTION APPLICATIONS

For bi-directional devices use CA suffix (e.g. SM15T12CA).

Electrical characteristics apply in both directions.

APPLICATION NOTES

A 1500 W (SMC) device is normally selected when the threat

of transients is from lightning induced transients, conducted

via external leads or I/O lines. It is also used to protect

against switching transients induced by large coils or

industrial motors. Source impedance at component level in

a system is usually high enough to limit the current within the

peak pulse current (IPP) rating of this series. In an overstress

condition, the failure mode is a short circuit.

FEATURES

• Low profile package

• Ideal for automated placement

• Glass passivated chip junction

• Available in uni-directional and bi-directional

• 1500 W peak pulse power capability with a

10/1000 μs waveform

• Excellent clamping capability

• Low inductance

• Meets MSL level 1, per J-STD-020, LF maximum peak

of 260 °C

• AEC-Q101 qualified

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

TYPICAL APPLICATIONS

Use in sensitive electronics protection against voltage

transients induced by inductive load switching and lighting

on ICs, MOSFET, signal lines of sensor units for consumer,

computer, industrial, automotive, and telecommunication.

MECHANICAL DATA

Case: SMC (DO-214AB)

Molding compound meets UL 94 V-0 flammability rating

Base P/N-E3 - RoHS-compliant and industrial grade

Base P/NHE3 - RoHS-compliant and AEC-Q101 qualified

Terminals: matte tin plated leads, solderable per

J-STD-002 and JESD 22-B102

E3 suffix meets JESD 201 class 2 whisker test, HE3 suffix

meets JESD 201 class 2 whisker test

Polarity: for uni-directional types the band denotes cathode

end, no marking on bi-directional types

Notes

(1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2

(2) Mounted on 0.31" x 0.31" (8.0 mm x 8.0 mm) copper pads to each terminal

PRIMARY CHARACTERISTICS

VWM 5.8 V to 188 V

VBR uni-directional 6.8 V to 220 V

VBR bi-directional 6.8 V to 220 V

PPPM 1500 W

PD6.5 W

IFSM (uni-directional only) 200 A

TJ max. 150 °C

Polarity Uni-directional, bi-directional

Package SMC (DO-214AB)

SMC (DO-214AB)

MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)

PARAMETER SYMBOL VALUE UNIT

Peak power dissipation with a 10/1000 μs waveform (1)(2) (fig. 1) PPPM 1500 W

Peak pulse current with a 10/1000 μs waveform (1) (fig. 3) IPPM See next table A

Power dissipation on infinite heatsink at TA = 50 °C PD6.5 W

Peak forward surge current 10 ms single half sine-wave uni-directional only (2) IFSM 200 A

Operating junction and storage temperature range TJ, TSTG -65 to +150 °C

SM15T Series

www.vishay.com Vishay General Semiconductor

Revision: 16-Jan-18 2Document Number: 88380

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

(1) For bi-directional devices add suffix “CA” instead of “A”

(2) VBR measured after IT applied for 300 μs square wave pulse

(3) For bi-polar devices with VRM = 10 V or under, the IRM limit is doubled

Note

(1) Mounted on minimum recommended pad layout

Note

(1) AEC-Q101 qualified

ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)

TYPE (1)

DEVICE

MARKING

CODE

BREAKDOWN

VOLTAGE

VBR AT IT (2)

(V)

TEST

CURRENT

(mA)

STAND-OFF

VOLTAGE

VRM

(V)

LEAKAGE

CURRENT

IRM AT VRM

ID (3)

(μA)

CLAMPING

VOLTAGE

VC AT IPPM

(10/1000 μs)

CLAMPING

VOLTAGE

VC AT IPPM

(8/20 μs)

T

MAX.

10-4/°C

UNI BI MIN. MAX. (V) (A) (V) (A)

SM15T6V8A GDE7 GDE7 6.45 7.14 10 5.80 1000 10.5 143 13.4 746 5.7

SM15T7V5A GDK7 BDK7 7.13 7.88 10 6.40 500 11.3 132 14.5 690 6.1

SM15T10A GDT7 BDT7 9.50 10.5 1.0 8.55 10 14.5 103 18.6 538 7.3

SM15T12A GDX7 BDX7 11.4 12.6 1.0 10.2 5.0 16.7 90.0 21.7 461 7.8

SM15T15A GEG7 GEG7 14.3 15.8 1.0 12.8 1.0 21.2 71.0 27.2 368 8.4

SM15T18A GEM7 BEM7 17.1 18.9 1.0 15.3 1.0 25.2 59.5 32.5 308 8.8

SM15T22A GET7 BET7 20.9 23.1 1.0 18.8 1.0 30.6 49.0 39.3 254 9.2

SM15T24A GEV7 GEV7 22.8 25.2 1.0 20.5 1.0 33.2 45.0 42.8 234 9.4

SM15T27A GEX7 BEX7 25.7 28.4 1.0 23.1 1.0 37.5 40.0 48.3 207 9.6

SM15T30A GFE7 BFE7 28.5 31.5 1.0 25.6 1.0 41.5 36.0 53.5 187 9.7

SM15T33A GFG7 GFG7 31.4 34.7 1.0 28.2 1.0 45.7 33.0 59.0 169 9.8

SM15T36A GFK7 BFK7 34.2 37.8 1.0 30.8 1.0 49.9 30.0 64.3 156 9.9

SM15T39A GFM7 BFM7 37.1 41.0 1.0 33.3 1.0 53.9 28.0 69.7 143 10.0

SM15T68A GGG7 GGG7 64.6 71.4 1.0 58.1 1.0 92.0 16.3 121 83 10.4

SM15T100A GGV7 GGV7 95.0 105 1.0 85.5 1.0 137 11.0 178 56 10.6

SM15T150A GHK7 GHK7 143 158 1.0 128 1.0 207 7.20 265 38 10.8

SM15T200A GHR7 GHR7 190 210 1.0 171 1.0 274 5.50 353 28 10.8

SM15T220A GHR8 GHR8 209 231 1.0 188 1.0 328 4.60 388 26 10.8

THERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)

PARAMETER SYMBOL VALUE UNIT

Typical thermal resistance, junction to ambient air (1) RJA 75 °C/ W

Typical thermal resistance, junction to lead RJL 15

ORDERING INFORMATION (Example)

PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE

SM15T10A-E3/57T 0.211 57T 850 7" diameter plastic tape and reel

SM15T10A-E3/9AT 0.211 9AT 3500 13" diameter plastic tape and reel

SM15T10AHE3/57T (1) 0.211 57T 850 7" diameter plastic tape and reel

SM15T10AHE3/9AT (1) 0.211 9AT 3500 13" diameter plastic tape and reel

SM15T Series

www.vishay.com Vishay General Semiconductor

Revision: 16-Jan-18 3Document Number: 88380

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)

Fig. 1 - Peak Pulse Power Rating Curve

Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature

Fig. 3 - Pulse Waveform

Fig. 4 - Typical Junction Capacitance Uni-Directional

Fig. 5 - Typical Transient Thermal Impedance

Fig. 6 - Maximum Non-Repetitive Forward Surge Current

Uni-Directional Use Only

0.1

100

PPM

- Peak Pulse Power (kW)

td - Pulse Width (s)

0.31 x 0.31" (8.0 x 8.0 mm)

Copper Pad Areas

0.1 µs 1.0 µs 10 µs 100 µs 1.0 ms 10 ms

0 25 50 75 100

100

125 150 175 200

TJ - Initial Temperature (°C)

Peak Pulse Power (P

) or Current (I

)

Derating in Percentage, %

100

150

= 10 µs

Peak Value

IPPM

Half Value -

IPPM

10/1000 µs Waveform

as defined by R.E.A.

01.0 2.0 3.0 4.0

t - Time (ms)

PPM

- Peak Pulse Current, % I

RSM

= 25 °C

Pulse Width (t

)

is defined as the Point

where the Peak Current

decays to 50 % of I

PPM

100

1000

10 000

20 000

101 100 400

Uni-Directional

Bi-Directional

= 25 °C

f = 1.0 MHz

sig

= 50 mVp-p

Measured at

Zero Bias

, Measured at

Stand-Off

Voltage, V

- Junction Capacitance (pF)

- Reverse Stand-Off Voltage (V)

0.1

1.0

100

0.001 0.01 0.1 10 1 100 1000

t - Pulse Duration

(

)

Transient Thermal Impedance (°C/W)

100

200

TJ = TJ max.

8.3 ms Single Half Sine-Wave

Number of Cycles at 60 Hz

Peak Forward Surge Current (A)

SM15T Series

www.vishay.com Vishay General Semiconductor

Revision: 16-Jan-18 4Document Number: 88380

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PACKAGE OUTLINE DIMENSIONS in inches (millimeters)

0.260 (6.60)

0.280 (7.11)

0.006 (0.152)

0.012 (0.305)

0.030 (0.76)

0.060 (1.52)

0.008 (0.2)

0.305 (7.75)

0.320 (8.13)

0.220 (5.59)

0.246 (6.22)

0.079 (2.06)

0.103 (2.62)

0.114 (2.90)

0.126 (3.20)

Cathode Band

SMC (DO-214AB)

0.320 REF.

Mounting Pad Layout

0 (0)

0.185 (4.69)

MAX.

0.126 (3.20)

MIN.

0.060 (1.52)

MIN.

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 08-Feb-17 1Document Number: 91000

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Vishay:

SM15T100A/57T SM15T100A/59T SM15T100A/9AT SM15T100A/9T SM15T100A-E3/51T SM15T100A-E3/57T

SM15T100A-E3/59T SM15T100A-E3/9AT SM15T100AHE3/57T SM15T100AHE3/59T SM15T100AHE3/9AT

SM15T100CA/57T SM15T100CA/59T SM15T100CA/7T SM15T100CA/9AT SM15T100CA-E3/51T SM15T100CA-

E3/57T SM15T100CA-E3/59T SM15T100CA-E3/9AT SM15T100CAHE3/57T SM15T100CAHE3/59T

SM15T100CAHE3/9AT SM15T10A/57T SM15T10A/59T SM15T10A/9AT SM15T10A-E3/51T SM15T10A-E3/57T

SM15T10A-E3/59T SM15T10A-E3/9AT SM15T10AHE3/57T SM15T10AHE3/59T SM15T10AHE3/9AT

SM15T10CA/57T SM15T10CA/59T SM15T10CA/9AT SM15T10CA-E3/51T SM15T10CA-E3/57T SM15T10CA-

E3/59T SM15T10CA-E3/9AT SM15T10CAHE3/57T SM15T10CAHE3/59T SM15T10CAHE3/9AT SM15T12A/57T

SM15T12A/59T SM15T12A/9AT SM15T12A-E3/51T SM15T12A-E3/57T SM15T12A-E3/59T SM15T12A-E3/9AT

SM15T12AHE3/57T SM15T12AHE3/59T SM15T12AHE3/9AT SM15T12CA/57T SM15T12CA/59T SM15T12CA/7T

SM15T12CA/9AT SM15T12CA-E3/51T SM15T12CA-E3/57T SM15T12CA-E3/59T SM15T12CA-E3/9AT

SM15T12CAHE3/57T SM15T12CAHE3/59T SM15T12CAHE3/9AT SM15T150A/57T SM15T150A/59T

SM15T150A/7T SM15T150A/9AT SM15T150A-E3/51T SM15T150A-E3/57T SM15T150A-E3/59T SM15T150A-

E3/9AT SM15T150AHE3/57T SM15T150AHE3/59T SM15T150AHE3/9AT SM15T150CA/57T SM15T150CA/59T

SM15T150CA/9AT SM15T150CA-E3/51T SM15T150CA-E3/57T SM15T150CA-E3/59T SM15T150CA-E3/9AT

SM15T150CAHE3/57T SM15T150CAHE3/59T SM15T150CAHE3/9AT SM15T15A/57T SM15T15A/59T

SM15T15A/7T SM15T15A/9AT SM15T15A-E3/51T SM15T15A-E3/57T SM15T15A-E3/59T SM15T15A-E3/9AT

SM15T15AHE3/57T SM15T15AHE3/59T SM15T15AHE3/9AT SM15T15CA/57T SM15T15CA/59T SM15T15CA/9AT

SM15T15CA-E3/51T SM15T15CA-E3/57T