SLR-343x/SLR343x Series
Data Sheet
■Features
■Outline
•
Viewing angle 2θ 1/2 : 40°
•
Competent to direct mount
■Dimensions
■Recommended Solder Pattern
■Specifications
Typ. I
F
Max. V
R
I
F
Min. Typ. I
F
(V) (mA) (µA) (V) (mA) (mcd) (mcd) (mA)
5.6 16
9.0 25
5.6 16
9.0 25
3.6 10
9.0 25
Emitting
Color
*1 : Duty1/5, 200kHz
Yellow Green
Green
GaP
Forward Voltage V
F
Reverse Current I
R
Peak Wavelength λ
P
Dissipation
T
opr
(ºC) T
stg
(ºC)
Red
60
60*
1
3 -25〜+85
-30
〜
+100
P
D
(mW)
I
F
(mA)
Typ.
(nm)
650
610
585
563
555
75
10
Absolute Maximum Ratings (Ta=25ºC) Electrical and Optical Characteristics (Ta=25ºC)
Power
Forward
Luminous Intensity I
V
3 10
5.6 16
6.3
25
2.2
Reverse
Operating Temp.
Storage Temp.
20
Peak Forward
Part No.
Chip Structure
GaAsP
I
FP
(mA)
V
R
(V)
Current
Current
Voltage
SLR-343VR
SLR-343PC
10
Orange
Yellow
2.1
SLR-343VC
SLR-343DU
SLR-343DC
SLR-343YY
SLR-343YC
SLR-343MG
SLR-343MC
SLR-343PG
2.0
10
Tolerance : ±0.2
(unit : mm) (unit : mm)
VDY
Color
Type M
P E B WB
2.5 or 5.0
2.0
1.0
±0.1
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 1/10 2019.3 - Rev.007
[Data Sheet]
■Specifications
Typ. I
F
Max. V
R
I
F
Min. Typ. I
F
(V) (mA) (µA) (V) (mA) (mcd) (mcd) (mA)
3.3 900
2200
3.2 420
1500
3.3 600
220
470
1000
330 680
1500 3300
Emitting
Color
[SLR-343x/SLR343x series]
Part No.
Chip Structure
Absolute Maximum Ratings (Ta=25ºC) Electrical and Optical Characteristics (Ta=25ºC)
Luminous Intensity I
V
Power
Forward Peak Forward
Reverse
Dissipation
Current
Current
Voltage
Typ.
P
D
(mW)
I
F
(mA)
I
FP
(mA)
V
R
(V) T
opr
(ºC) T
stg
(ºC) (nm)
Operating Temp.
Storage Temp.
Forward Voltage V
F
Reverse Current I
R
Dominant Wavelength λ
D
/Chromaticity coordinate(x,y)
SLR343EC4T
525
SLR343BCT 200
SLR343BC4T
3.2
SLR343BD2T
SLR343WBD2PT *3
SLR343ECT
InGaN
Green
120
100*
2
5 -20〜+80
-30〜+100
*2:Duty 1/10,1kHz、*3:Brightness for white color is noted with chromaticity coordinate(x,y).
SLR343BC7T
105
126
30
25
30
100
10
470
SLR343WBC7T *3
Blue
White 105
126
25
30
(x,y)(0.31, 0.31)
47020 5
527
20 20
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 2/10 2019.3 - Rev.007
[Data Sheet]
■Electrical Characteristics Curves
Fig.1 Forward Current
Fig.2 Luminous Intensity -
- Forward Voltages
Atmosphere Temperature
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
Reference
[SLR-343x/SLR343x series]
0
1.2
1.0
0.8
0.6
0.4
0.2
0 5 10 15 20
25
1.4
1.2
1.0
0.8
0.6
0.4
-40 -20 0 20 40 60 80 100
1.0 1.5 2.0 3
.0
2.5
50
20
10
5.0
2.0
1.0
0.5
0.2
0.1
Ta=25ºC
FORWARD CURRENT : IF[mA]
FORWARD VOLTAGE : VF[V]
IF=10mA
RELATIVE LUMINOUS INTENSITY [a.u.]
ATMOSPHERE TEMPERATURE : Ta [ºC]
Ta=25ºC
RELATIVE LUMINOUS INTENSITY
FORWARD CURRENT : IF[mA]
MAXIMUM FORWARD CURRENT : [mA]
AMBIENT TEMPERATURE : Ta [ºC]
SLR-343VR
SLR-343VC
SLR-343DU
SLR-343DC
SLR-343YY
SLR-343YC
SLR-343MG
SLR-343MC
SLR-343PG
SLR-343PC
SLR
-343VR
SLR
-343VC
SLR
-343DU
SLR
-343DC
SLR
-343YY
SLR
-343YC
SLR
-343MG
SLR
-343MC
SLR
-343PG
SLR
-343PC
SLR
-343VR
SLR
-343VC
SLR
-343DU
SLR
-343DC
SLR
-343YY
SLR
-343YC
SLR
-343MG
SLR
-343MC
SLR
-343PG
SLR
-343PC
0
10
20
30
-40 -20 0 20 40 60 80 1
00
SLR
-343VR
SLR
-343VC
SLR
-343DU
SLR
-343DC
SLR
-343YY
SLR
-343YC
SLR
-343MG
SLR
-343MC
SLR
-343PG
SLR
-343PC
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 3/10 2019.3 - Rev.007
[Data Sheet]
■Electrical Characteristics Curves
Fig.1 Forward Current
Fig.2 Luminous Intensity -
- Forward Voltages
Atmosphere Temperature
Fig.3 Luminous Intensity - Forward Current
Fig.4 Derating
Reference
[SLR-343x/SLR343x series]
1.4
1.2
1.0
0.8
0.6
0.4
-40 -20 0 20 40 60 80 100
1.6
Ta=25ºC IF=20mA
Ta=25ºC
FORWARD CURRENT : IF[mA]
FORWARD VOLTAGE : VF[V]
RELATIVE LUMINOUS INTENSITY [a.u.]
ATMOSPHERE TEMPERATURE : Ta [ºC]
RELATIVE LUMINOUS INTENSITY
FORWARD CURRENT : IF[mA]
MAXIMUM FORWARD CURRENT : [mA]
AMBIENT TEMPERATURE : Ta [ºC]
SLR343ECT
SLR343BCT
SLR343EC4T
SLR343BC4T
SLR343BD2T
SLR343WBD2PT
SLR343BC7T
SLR343WBC7T
SLR343ECT
SLR343EC4T
SLR343BCT
SLR343BC4T
SLR343BD2T
SLR343BC7T
SLR343WBC7T
SLR343WBD2PT
SLR343ECT
SLR343EC4T
SLR343BCT
SLR343BC4T
SLR343BD2T
SLR343WBD2PT
SLR343BC7T
SLR343WBC7T
0
10
20
40
30
-40 -20 0 20 40 60 80 1
00
SLR343ECT
SLR343EC4T
SLR343BCT
SLR343BC4T
SLR343BD2T
SLR343WBD2PT
SLR343BC7T
SLR343WBC7T
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 4/10 2019.3 - Rev.007
[Data Sheet]
■Viewing Angle
Reference
[SLR-343x/SLR343x series]
SCANNING ANGLE (deg)
RELATIVE INTENSITY (%)
SLR
-343x Series
SCANNING ANGLE (deg)
RELATIVE INTENSITY (%)
10°
10° 20°
20°
40°
50°
70°
80°
40°
50°
70°
80°
0
5
0
100
50
100
0°
30°
60°
90°
30°
60°
90°
Diffused
Clear
10°
10° 20°
20°
40°
50°
70°
80°
40°
50°
70°
80°
0
5
0
100
50
100
0°
30°
60°
90°
30°
60°
90°
SLR343BD2T
SCANNING ANGLE (deg)
RELATIVE INTENSITY (%)
10°
10° 20°
20°
40°
50°
70°
80°
40°
50°
70°
80°
0
5
0
100
50
100
0°
30°
60°
90°
30°
60°
90°
SLR343BCT / ECT / WBD2PT/WBC7T
SLR343BC4T / EC4T
RELATIVE INTENSITY (%)
SCANNING ANGLE (deg)
SLR343BC7T
050 100
90
80
70
60
50
40
30
20
10
0
10
20
30
40
50
60
70
80
90
100 50
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 5/10 2019.3 - Rev.007
[Data Sheet]
■Rank Reference of Brightness*
*Measurement tolerance：±10%
■Chromaticity Diagram
[SLR-343x/SLR343x series]
0.2
0.3
0.4
0.2 0.3 0.4
CIE x
CIE y
1
2
3
4
Red (V)
(Ta=25ºC, I
F
＝10mA)
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
0.40〜0.63
0.63〜1.0
1.0〜1.6 1.6〜2.5 2.5〜4.0 4.0〜6.3
6.3〜10 10〜16 16〜25 25〜40 40〜63
63〜100
100〜160 160〜250 250〜400 400〜630
Orange(D)
(Ta=25ºC, I
F
＝10mA)
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
0.40〜0.63
0.63〜1.0
1.0〜1.6 1.6〜2.5 2.5〜4.0 4.0〜6.3
6.3〜10 10〜16 16〜25 25〜40 40〜63
63〜100
100〜160 160〜250 250〜400 400〜630
Yellow (Y)
(Ta=25ºC, I
F
＝10mA)
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
0.40〜0.63
0.63〜1.0
1.0〜1.6 1.6〜2.5 2.5〜4.0 4.0〜6.3
6.3〜10 10〜16 16〜25 25〜40 40〜63
63〜100
100〜160 160〜250 250〜400 400〜630
Yellow Green/Green(M,P)
(Ta=25ºC, I
F
＝10mA)
E
F
G
H
J
K
L
M
N
P
Q
R
S
T
U
V
0.40〜0.63
0.63〜1.0
1.0〜1.6 1.6〜2.5 2.5〜4.0 4.0〜6.3
6.3〜10 10〜16 16〜25 25〜40 40〜63
63〜100
100〜160 160〜250 250〜400 400〜630
Green(E)
(Ta=25ºC, I
F
＝20mA)
XH
XJ
XK
XL
XM
XN
XP
XQ
XR
XS
XT
XU
135〜240 200〜360 300〜520
420〜 750
610〜1100 900〜1650 1350〜2400 2000〜3600 3000〜5200 4200〜7500
6100〜11000 9000〜16500
Blue(B)
(Ta=25ºC, I
F
＝20mA)
XH
XJ
XK
XL
XM
XN
XP
XQ
XR
XS
XT
XU
135〜240 200〜360 300〜520
420〜 750
610〜1100 900〜1650 1350〜2400 2000〜3600 3000〜5200 4200〜7500
6100〜11000 9000〜16500
XH
XJ
XK
XL
XM
XN
XP
XQ
XR
XS
XT
XU
150〜220 220〜330 330〜470
470〜 680
680〜1000 1000〜1500 1500〜2200 2200〜3300 3300〜4700 4700〜6800
6800〜10000
10000〜15000
White(WB)
(Ta=25ºC, I
F
＝20mA)
XH
XJ
XK
XL
XM
XN
XP
XQ
XR
XS
XT
XU
150〜220 220〜330 330〜470
470〜 680
680〜1000 1000〜1500 1500〜2200 2200〜3300 3300〜4700 4700〜6800
6800〜10000
10000〜15000
Iv (mcd)
Rank
Iv (mcd)
Rank
Iv (mcd)
SLR343BD2T
SLR343BCT
SLR343WBC7T
SLR343BC7T
Rank
Iv (mcd)
Rank
Iv (mcd)
Rank
Iv (mcd)
Rank
SLR-343VC
SLR-343VR
SLR-343DC
SLR-343DU
Iv (mcd)
Rank
Iv (mcd)
Rank
SLR343WBD2P
SLR-343YC
SLR-343YY
SLR-343MC
SLR-343MG
SLR-343PG
SLR-343PC
SLR343EC4T
SLR343ECT
SLR343BC4T
（Ｔａ＝25℃、If=20mA)
x
y
x
y
x
y
x
y
0.283 0.244 0.280 0.312 0.302 0.338 0.330 0.307
0.299 0.269 0.302 0.338 0.330 0.370 0.354 0.339
0.280 0.312 0.313 0.286 0.330 0.307 0.363 0.398
0.260 0.272 0.299 0.269 0.313 0.286 0.330 0.370
Measurement tolerance：±0.02
1234
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 6/10 2019.3 - Rev.007
[Data Sheet]
■Part No. Construction
[SLR-343x/SLR343x series]
*"-"will be taken out for emitting color Special Code will be applied for Chromaticity rank Rank sign
WB/B/E series. Emitting color WB/B/E series. (for white LED） (Brightness Rank)*
Series name Package type Emitting Color Resin Color Taping Specification
V R
U U
U2 Y
D G
Y C
Y2 RC
M T
P
E
B
*Concerning the Brightness rank.
WB
*Please refer to the rank chart above for
luminous intensity classification.
*Part name is individual for each rank.
*When shipped as sample,the part name will
be a representative part name.
General products are free of ranks.
Please contact sales if rank appointment
is needed.
3T
Transparent Coloreless
S L R － 3 4 3 M T
Yellow
Transparent Colored
P
3F
T□□
1-Element straight bulk
2
See Taping specifications
<Red>DiffusedColored
SLI
1-Die Circular Type Low Current High Brightness LED Lamps
Red
<Orange>DiffusedColored
SLA
1-Die Circular Type High Brightness LED Lamps
Red
<Yellow>DiffusedColored
SLD
1-Die Oval Type High Brightness LED Lamps
Orange
<Yellowish green>DiffusedColored
Green
Blue
White
SLR 1-Die Circular Type LED Lamps Red
Green
Yellow
Yellow green
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 7/10 2019.3 - Rev.007
[Data Sheet]
Visual light emitting diode does not contain reinforcement materials such as glass fillers.
Therefore if sudden thermal and mechanical shock are given, destruction or inferiority of luminous
intensity may occur. Please take care of the handling.
Please consult with us if any problems in the evaluation stage.
■ATTENTION POINTS IN HANDLING
to avoid the remained stress and solder heat stress.
Enough evaluation is requested before deciding assembly and soldering conditions.
failure during soldering or using. Please design the through-holes of PCB suitable for lead pins
space or lead pins space after forming to avoid the physical stress on resin.
(1) In case of soldering on PCB, If the operation is done with stress, it may cause non-lighting
[SLR-343x/SLR343x series]
In case of direct mount on PCB(SLR/SLI-343 series), please take care about clinch of LED pins
■FIXATION METHOD
１．ATTENTION POINTS
(1) Please do not give excessive heat over storage temperature to resin.
In case that the product has to be heated in oven for the glue fixing of surface mount parts,
this LED should be mounted after the glue fixing.
(2) Please avoid stress to resin at high temperature.
２． TERMINATION PROCESSING
(1) In case of termination processing, please fix the
termination
(2) Processing position, and process the reverse side
of LED body.
If stress is given during processing, It may cause
non-lighting failure.
(3) Please process before soldering.
３． ASSEMBLY ON PC BOARD
(2) Using spacer between LEDʼs body and PCB is recommended.
＜Good＞ ＜No good＞
To be fixed To be fixed
＜Good＞ ＜No good＞＜Good＞
＜2 lead pins type＞
＜3 lead pins type＞
＜2 lead pin type＞
Min.15°Min.45°
Die bonding side
＜3 lead pin type＞
Min.15°Min.45°
Die bonding side
Min.45
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 8/10 2019.3 - Rev.007
[Data Sheet]
Soldering Dip
Soldering Bath
Max. 265℃ 5sec Max.
Soldering Iron
Max. 400℃
3sec Max.
The iron should not touch the LEDʼs body.
＜Recommendable soldering conditions＞
60sec Max.
ARTIICLE
SOLDERINGTEMP
OPERATION TIME
Remarks
－
Pre-heat
Max. 100℃
less than 100 degree C.
[SLR-343x/SLR343x series]
４．SOLDERING（Sn-3Ag-0.5Cu）
(1) Please make soldering rapidly under the following temperature and time conditions.
(2) Please avoid stress to LED lamp during soldering.
(3) In case of double peak flow soldering, the temperature gap during 1st and 2nd soldering to be
to the end of 2nd peak.
Temperature of solvent
：Max. 45℃
so please check the solvent before actual use.
Immersion time
：Max. 3min
５．CLEANING
６．RECOMMENDABLE ROUND PATTERN
Round pattern depends on the material PCB, density and circuit arrangement.
■ATTENTION ON STORAGING
Storage in dry box is most desirable, but if it is not possible, we recommend following conditions.
＜RECOMMENDABLE STORAGE CONDITIONS＞
ARTICLE
Temperature
Humidity
Expiration Date
Our recommendation is as follow :
CONDITIONS
5〜30℃
In case of double peak flow soldering, the operation
time is counted from the beginning of 1st peak
Ultrasonic out
：Max. 15W/Liter
The recommendable cleaning solvent is alcoholic one such as isopropyl alcohol.
＜RECOMMENDABLE CLEANING CONDITIONS＞
METHOD
CONDITIONS
Cleaning by solvent
Cleaning by solvent
Cleaning time
：Max. 3min
In case of cleaning, some solvents may cause damage of resin or cause non-lighting failure,
Max.60%RH
Within 1 year
Poor storage conditions may cause some failure as bellow.
(1) Lead pins may corrode if it is stored in the environment of high temperature and humidity
and lead to defective soldering.
(2) In case of soldering after LEDʼs body absorb moisture highly, destruction or inferiority of
luminous intensity may occur.
<2 lead pin type> <3 lead pin type/2.5mm pitch> ＜3 lead pin type/2.0mm pitch>
1.5
±0.1
1.0
2.0
2.0
φ2.0
2.0
2.5
or
5.0
±0.1
1.0 2.0
±0.1
1.0
2.5
2.5
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 9/10 2019.3 - Rev.007
[Data Sheet]
The Product is LED. We are not responsible for the usage as the diode such as Protection Chip,
Rectifier, Switching and so on.
The product is part of semiconductor and electrostatic sensitive, thereʼs high possibility to be
damaged by the electrostatic discharge.
Please take appropriate measures to avoid the static electricity from human body and earthing
setting of production equipment. The resistance values of electrostatic discharge (actual values)
are different varies with products, therefore, please call our Sales staffs for inquiries.
Applications with strong electromagnetic wave such as, IH cooker, will influence the reliability of LED,
therefore please evaluate before using it.
(ammonia), it may result in low soldering ability (caused by the change in quality of the plating
die bonding (Ag-paste) materials. All of the above will cause function failure of the products.
Therefore, please pay attention to the storage environment for mounted product (concern the
generated gas of the surrounding parts of the products and the atmospheric environment).
２. Electrostatic Damage
３. Electromagnetic Wave
[SLR-343x/SLR343x series]
■APPLICATION METHOD
１．Precaution for Drive System and Off Mode
・Design the circuit without the electric load exceeding the ABSOLUTE MAXIMUM RATING that
applies on the products.
・If drive by constant voltage, it may cause current deviation of the LED and result in deviation of
luminous intensity, so we recommend to drive by constant current. (Deviation of VF Value will
cause deviation of current in LED.)
・Furthermore, for off mode, please do not apply voltage neither forward nor reverse. Especially,
for the products with the Ag-paste used in the die bonding, thereʼs high possibility to cause electro
migration and result in function failure.
２. Operation Life Span
Thereʼs possibility for intensity of light drop according to working conditions and environments
(applied current, surrounding temperature and humidity, corrosive gases ), please call our Sales
(1) Longtime intensity of light life
３. Usage
staffs for inquiries about the concerned application below.
(2) On mode all the time
■OTHERS
１. Surrounding Gas
Notice that if it is stored under the condition of acid gas (chlorine gas, sulfured gas) or alkali gas
surface ) or optical characteristics changes (light intensity, chrominance) and change in quality of
＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
www.rohm.co.jp
©2019 ROHM Co., Ltd. All rights reserved 10/10 2019.3 - Rev.007
R1102
A
www.rohm.com
© 201 ROHM Co., Ltd. All rights reserved.
Notice
ROHM Customer Support System
http://www.rohm.com/contact/
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
Notes
The information contained herein is subject to change without notice.
Before you use our Products, please contact our sales representative
and verify the latest specifica-
tions :
Although ROHM is continuously working to improve product reliability and quality, semicon-
ductors can break down and malfunction due to various factors.
Therefore, in order to prevent personal injury or fire arising from failure, please take safety
measures such as complying with the derating characteristics, implementing redundant and
fire prevention designs, and utilizing backups and fail-safe procedures. ROHM shall have no
responsibility for any damages arising out of the use of our Poducts beyond the rating specified by
ROHM.
Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral
conditions must be taken into account when designing circuits for mass production.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly,
any license to use or exercise intellectual property or other rights held by ROHM or any other
parties. ROHM shall have no responsibility whatsoever for any dispute arising out of the use of
such technical information.
The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communi-
cation, consumer systems, gaming/entertainment sets) as well as the applications indicated in
this document.
The Products specified in this document are not designed to be radiation tolerant.
For use of our Products in applications requiring a high degree of reliability (as exemplified
below), please contact and consult with a ROHM representative : transportation equipment (i.e.
cars, ships, trains), primary communication equipment, traffic lights, fire/crime prevention, safety
equipment, medical systems, servers, solar cells, and power transmission systems.
Do not use our Products in applications requiring extremely high reliability, such as aerospace
equipment, nuclear power control systems, and submarine repeaters.
ROHM shall have no responsibility for any damages or injury arising from non-compliance with
the recommended usage conditions and specifications contained herein.
ROHM has used reasonable care to ensur the accuracy of the information contained in this
document. However, ROHM does not warrants that such information is error-free, and ROHM
shall have no responsibility for any damages arising from any inaccuracy or misprint of such
information.
Please use the Products in accordance with any applicable environmental laws and regulations,
such as the RoHS Directive. For more details, including RoHS compatibility, please contact a
ROHM sales office. ROHM shall have no responsibility for any damages or losses resulting
non-compliance with any applicable laws or regulations.
When providing our Products and technologies contained in this document to other countries,
you must abide by the procedures and provisions stipulated in all applicable export laws and
regulations, including without limitation the US Export Administration Regulations and the Foreign
Exchange and Foreign Trade Act.
This document, in part or in whole, may not be reprinted or reproduced without prior consent of
ROHM.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
