ADL6317-EVALZ User Guide UG-1609 One Technology Way * P.O. Box 9106 * Norwood, MA 02062-9106, U.S.A. * Tel: 781.329.4700 * Fax: 781.461.3113 * www.analog.com Evaluating TxVGAs for Use with RF DACs and Transceivers FEATURES GENERAL DESCRIPTION Full featured evaluation board for the ADL6317 SPI control via SDP-S board 5.0 V single-supply operation The ADL6317 is a transmit variable gain amplifier (VGA) that provides an interface from radio frequency (RF) digital-toanalog converters (DACs), transceivers, and systems on a chip (SoC) to power amplifiers (PAs). Integrated balun and hybrid couplers allow high performance RF capability in the 1.5 GHz to 3.0 GHz frequency range EVALUATION KIT CONTENTS ADL6317-EVALZ evaluation board ADDITIONAL HARDWARE REQUIRED Analog signal generator Analog signal analyzer Power supplies (6 V, 5 A) PC with Windows(R) XP, Windows 7, or Windows 10 operating system USB 2.0 port, recommended (USB 1.1-compatible) EVAL-SDP-CS1Z (SDP-S) controller board ADDITIONAL SOFTWARE REQUIRED To optimize performance vs. power level, the ADL6317 includes a voltage variable attenuator (VVA), high linearity amplifiers, and a digital step attenuator (DSA). The devices integrated into the ADL6317 are programmable via a 4-wire serial port interface (SPI). This user guide describes the evaluation board and software for the ADL6317. See the ADL6317 data sheet for full details, which must be consulted in conjunction with this user guide when using the evaluation board. The ADL6317 evaluation board was fabricated using FR-370HR, Rogers 4350B in four layers. Analysis | Control | Evaluation (ACE) software 20927-001 EVALUATION BOARD PHOTOGRAPH Figure 1. ADL6317 Evaluation Board PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 8 UG-1609 ADL6317-EVALZ User Guide TABLE OF CONTENTS Features .............................................................................................. 1 RF Input ..........................................................................................3 Evaluation Kit Contents ................................................................... 1 RF Outputs .....................................................................................3 Additional Hardware Required ...................................................... 1 Signal Path Modes Selection ........................................................3 Additional Software Required ........................................................ 1 Evaluation Board Software ...............................................................4 General Description ......................................................................... 1 Software Requirements and Installation ....................................4 Evaluation Board Photograph......................................................... 1 Installing ADL6317 ACE Plugins ...............................................4 Revision History ............................................................................... 2 ACE Software Suite .......................................................................4 Evaluation Board Hardware ............................................................ 3 Configuration and Programming Sequence..............................5 Power Supply ................................................................................. 3 Evaluation Board Schematic ............................................................7 REVISION HISTORY 10/2019--Revision 0: Initial Version Rev. 0 | Page 2 of 8 ADL6317-EVALZ User Guide UG-1609 EVALUATION BOARD HARDWARE The ADL6317-EVALZ evaluation board provides the support circuitry required to operate the ADL6317 in various modes and configurations. Figure 2 shows the typical bench setup to evaluate the performance of the ADL6317. RF OUTPUTS The RF outputs are available on the evaluation board at the RF_OUT SMA connectors, which can drive a load of 50 . SIGNAL PATH MODES SELECTION POWER SUPPLY The ADL6317 has two signal path modes. This feature allows two predefined modes of operation to be controlled by the logic level on TXEN, a real-time external pin (Pin 37) with no SPI latency. Table 1 shows the hardware configuration to select the desired mode. The ADL6317-EVALZ evaluation board requires a single, 5.0 V power supply. RF INPUT The on-board balun enables single-ended driving. The ADL6317 operates over a frequency range of 1.5 GHz to 3.0 GHz. USB VVA CONTROL VOLTAGE GND RF INPUT RF OUTPUT GND 20927-002 +5.0V Figure 2. ADL6317 Typical Measurement Setup Table 1. Mode Selection and Setup Registers TXEN(Pin 37) 0 1 Register 0x0102 0x0107 0x0108 0x0109 0x010A 0x0112 0x0117 0x0118 0x0119 0x011A Functional Blocks DSA attenuation AMP1 AMP1 AMP2 AMP2 DSA attenuation AMP1 AMP1 AMP2 AMP2 Rev. 0 | Page 3 of 8 Description 0 dB to ~15.5 dB range, 0.5dB step Amplifier 1 optimization Amplifier 1 enable Amplifier 2 optimization Amplifier 2 enable 0 dB to ~15.5 dB range, 0.5dB step Amplifier 1 optimization Amplifier 1 enable Amplifier 2 optimization Amplifier 2 enable UG-1609 ADL6317-EVALZ User Guide EVALUATION BOARD SOFTWARE The ADL6317 on the ADL6317-EVALZ evaluation board and the SDP-S controller board are configured with a USB friendly interface to allow programmability of the ADL6317 registers. SOFTWARE REQUIREMENTS AND INSTALLATION The ACE software suite allows bit control of the ADL6317 register map via the SPI, and communicates to the SDP-S controller board via the USB connection. The SDP-S controller board configures the SPI lines (CS, SDI, SDO, and SCLK) accordingly to communicate to the ADL6317. 20927-003 The Analysis | Control | Evaluation (ACE) software is required to program and control the ADL6317 and the ADL6317-EVALZ evaluation board. Figure 3. ACE Plugin View 2. Installing the ACE Software Suite Double-click the ADL6317-EBZ board icon, as shown in Figure 4. 1. 2. 3. Download the software from the ACE product page. Open the downloaded file to begin the installation process. The default installation path is C:\Program Files (x86)\ Analog Devices\ACE. If desired, the user can create a desktop icon for the ACE software. Otherwise, the ACE executable can be found by clicking Start > Analog Devices > ACE. 20927-004 To install the ACE software suite, take the following steps: Figure 4. ADL6317-EBZ Board Icon 3. The software opens the ACE chip view as shown in Figure 5. INSTALLING ADL6317 ACE PLUGINS 1. Download ADL6317 ACE plugins (Board.ADL631x.1.2019. 34200.acezip) from the ADL6317-EVALZ product page. 2. Double-click the Board.ADL631x.1.2019.34200.acezip file to install the evaluation board plugins. Ensure that the Board.ADL631x.1.2019.34200 and Chip. ADL631x.1.2019.34200 folders are located inside the C:\ProgramData\Analog Devices\ACE\Plugins folder. 3. ACE SOFTWARE SUITE Power up the ADL6317-EVALZ evaluation board and connect the USB cable to the PC and to the SDP-S board mounted on the ADL6317-EVALZ evaluation board. 1. Double-click the ACE shortcut on the PC desktop of the computer (if created). The software automatically detects the ADL6317-EVALZ evaluation board. The software opens the ACE plugin view, as shown in Figure 3. Rev. 0 | Page 4 of 8 20927-005 When the ACE software installations are complete, the user must install the evaluation board plugins to the hard drive of the PC. Figure 5. ACE Chip View ADL6317-EVALZ User Guide UG-1609 4. CONFIGURATION AND PROGRAMMING SEQUENCE To configure and program the evaluation board, take the following steps: 1. 2. 3. After changing the block as directed in Step 3, in the ACE software, click Apply Changes (Label K, see Figure 7) to update to ADL6317. To adjust an individual register and bit, click Proceed to Memory Map. This button opens the ADL6317 memory map for bit control (see Figure 8). The ADL6317 can be configured by either putting data into Data(Hex) column or by clicking a specific bit in the Data(Binary) column of the register map (see Figure 8). Click Apply Changes to save changes and program the ADL6317. 5. Run the ACE software as explained in the ACE Software Suite. Click Initialize Chip (Label A, see Figure 6). Click and adjust the blocks in Label B to Label H, as shown in Figure 6, if necessary. G B A H I J J1 J2 C D C1 C3 E F D1 E1 D2 F1 E2 D3 F2 C2 20927-006 C4 Figure 6. ADL6317 Chip Block Diagram Table 2. Main Screen Functionality (see Figure 6) Label A B C C1 C2 C3 C4 D D1 D2 D3 E F G H I J J1 J2 Function Initialize chip button. 3.3 V low dropout regulator (LDO) enable. VVA control block. VVA Enable checkbox. Selects VVA voltage source: DAC: VVA attenuation set by internal 12-bit DAC, set DAC code (0 to ~4095 range) in VVA Atten (Dec Code) field. VVA_ANALOG: VVA attenuation set by analog voltage applied on ANLG pin. DAC Enable checkbox for VVA attenuation when the VVA Source field is set to DAC. VVA Atten (Dec Code) menu. Selects VVA DAC code in decimal (0 to ~4095 range). Higher numbers equal less attenuation. DSA control block, DSA Atten 0 and DSA Atten 1 are selected by the logic level on TXEN (see Table 1). DSA Enable checkbox. Set DSA Atten 0 attenuation. Set DSA Atten 1 attenuation. AMP1 Enable checkbox. AMP1 can be set individually by the logic level on TXEN (see Table 1). AMP2 Enable checkbox. AMP2 can be set individually by the logic level on TXEN (see Table 1). Read Temp Sensor button and ADC Code text fields. These functions are for proportional to absolute temperature (PTAT) ADC code readback. ADC Enable checkbox. IBIAS Enable checkbox. This function enables the bias generator. IP3 Optimization control block. Enable checkbox for IP3 optimization. TRM AMP2 IP3M dropdown menu. Set the TRM_AMP2_IP3 bits value for IP3 optimization. Rev. 0 | Page 5 of 8 UG-1609 ADL6317-EVALZ User Guide 20927-007 K Figure 7. ADL6317-EVALZ ACE Chip View After Chip Initialization N M 20927-008 L Figure 8. ADL6317-EVALZ ACE Memory Map View Rev. 0 | Page 6 of 8 1 Figure 9. ADL6317-EVALZ Evaluation Board Schematic AGND GND BLK 1 AGND 2 3 4 RF_IN 142-0701-851 1 GND_1 BLK AGND VDD25AMP 1 NC 5 6 T1 3 GND_2 BLK 4 P1 2 TCM1-63AX+ 1 AGND R6 100k 1 2 3 TSW-103-08-G-S AGND C14 0.1F AGND VDD25AMP INN1 INP1 AGND GND GND IN_N IN_P VDAC GND AGND 1 2 3 P4 TSW-103-08-G-S 1 2 3 4 5 6 SDO SCLK SDI CS 1 R9 0 AMUX K24A/C PAD2 PAD1 38 37 36 35 34 33 32 31 30 29 28 27 26 ADL6317 DUT CS4 G V G V CS5 1 2 3 AGND P5 TSW-103-08-G-S AGND VDD25AMP C2 0.1F AGND C8 0.1F AGND 25 24 23 22 21 20 CS5 CS4 GND GND RF_OUT GND GND GND GND GND GND TXEN CS SDI SCLK SDO MUXOUT GND VVA_ANALOG CS5 CS4 NC GND GND GND GND NC NC GND V50AMP1 GND V33FUSE1 NC V50AMP2 NC GND 7 8 9 10 11 12 13 14 15 16 17 18 19 V5AMP1 R62 100k 1 TWI_A0 C38 0.1F AGND A0 AGND A1 SDA_SDP 5 SDA A2 SCL WP VSS 4 U2 8 VCC P6 2 1 TSW-102-08-G-S 24LC32A-I/MS E014160 JEDEC_TYPE=MSOP8 1 2 3 6 7 3P3V_SDP V5AMP1 C13 1F SCL_SDP 5V_1 RED WA_ANALOG K24A/C V5AMP2 5V_2 RED AGND C11 10pF 1 AGND 4 3 2 AGND R61 TBD0402 DNI AGND C3 10pF 1 C6 0.1F AGND 560 R11 RF_OUT 142-0701-851 1 AGND RFOUT AGND C5 0.27NF R60 Rev. 0 | Page 7 of 8 100k R5 100k AGND TWI_A0 13 12 11 10 9 8 7 6 5 4 3 2 1 J3 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 FX8-120S-SV(21) SDO SDI CS AGND DNI AGND SCL_SDP SDA_SDP 3P3V_SDP 1k R69 1k R68 DNI AGND C51 1000pF 0 R66 1k R67 C52 1000pF AGND C50 1000pF DNI DNI AGND C49 1000pF SCLK 108 109 110 111 112 113 114 115 116 117 118 119 120 J3 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 FX8-120S-SV(21) ADL6317-EVALZ User Guide UG-1609 EVALUATION BOARD SCHEMATIC 20927-009 UG-1609 ADL6317-EVALZ User Guide NOTES ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the "Evaluation Board"), you are agreeing to be bound by the terms and conditions set forth below ("Agreement") unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you ("Customer") and Analog Devices, Inc. ("ADI"), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term "Third Party" includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED "AS IS" AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER'S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI'S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed. (c)2019 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG20927-0-10/19(0) Rev. 0 | Page 8 of 8