SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 D Designed for TIA/EIA-485, TIA/EIA-422, and D D D D D D D ISO 8482 Applications Signaling Rate Exceeding 50 Mbps Fail-Safe in Bus Short-Circuit, Open-Circuit, and Idle-Bus Conditions ESD Protection on Bus Inputs Exceeds 6 kV Common-Mode Bus Input Range -7 V to 12 V Propagation Delay Times <16 ns Low Standby Power Consumption <20 A Pin-Compatible Upgrade for AM26LS32, DS96F173, LTC488, and SN75173 SN65LBC173A (Marked as 65LBC173A) SN75LBC173A (Marked as 75LBC173A) D or N PACKAGE (TOP VIEW) 1B 1A 1Y G 2Y 2A 2B GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC 4B 4A 4Y G 3Y 3A 3B logic diagram G description G The SN65LBC173A and SN75LBC173A are quadruple differential line receivers with 3-state outputs, designed for TIA/EIA-485 (RS-485), TIA/EIA-422 (RS-422), and ISO 8482 (Euro RS-485) applications. These devices are optimized for balanced multipoint bus communication at data rates up to and exceeding 50 million bits per second. The transmission media may be twisted-pair cables, printed-circuit board traces, or backplanes. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment. 1A 1B 1Y 2A 2B 2Y 3A 3B 3Y 4A 4B 4Y Each receiver operates over a wide range of positive and negative common-mode input voltages, and features ESD protection to 6 kV, making it suitable for high-speed multipoint data transmission applications in harsh environments. These devices are designed using LinBiCMOSt, facilitating low power consumption and robustness. The G and G inputs provide enable control logic for either positive- or negative-logic enabling all four drivers. When disabled or powered off, the receiver inputs present a high-impedance to the bus for reduced system loading. The SN75LBC173A is characterized for operation over the temperature range of 0C to 70C. The SN65LBC173A is characterized over the temperature range from -40C to 85C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. LinBiCMOS is a trademark of Texas Instruments. The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second). Copyright 2001, Texas Instruments Incorporated !"# $ %&'# "$ (&)*%"# +"#', +&%#$ %! # $('%%"#$ (' #-' #'!$ '."$ $#&!'#$ $#"+"+ /""#0, +&%# (%'$$1 +'$ # '%'$$"*0 %*&+' #'$#1 "** (""!'#'$, POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 FUNCTION TABLE (each receiver) ENABLES DIFFERENTIAL INPUTS A - B (VID) G G H X X L H X X L H X X L L H OPEN OPEN H X X L H X VID -0.2 V -0.2 V < VID < -0.01 V -0.01 V VID X Short circuit Open circuit H = high level, L = low level, ? = indeterminate OUTPUT Y L ? H Z H H X = irrelevant, Z = high impedance (off), AVAILABLE OPTIONS PACKAGE TA PLASTIC SMALL OUTLINE (JEDEC MS-012) PLASTIC DUAL-IN-LINE (JEDEC MS-001) 0C to 70C SN75LBC173AD SN75LBC173AN -40C to 85C SN65LBC173AD SN65LBC173AN Add an R suffix for taped and reeled equivalent input and output schematic diagrams A Input B Input VCC 16 V 100 k VCC 4 k 18 k Input Input 16 V G Input 4 k 16 V 18 k 4 k 16 V G Input VCC 100 k 4 k VCC Y Output VCC 100 k 1 k Input 100 k 8V 2 Input 8V 1 k 5 8V POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 8V Output 8V SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6 V Voltage range at any bus input (DC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10 V to 15 V Voltage range at any bus input (transient pulse through 100 , see Figure 5) . . . . . . . . . . . . . . -30 V to 30 V Voltage input range at G and G, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V Receiver output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA Electrostatic discharge: Human body model (see Note 2): A and B to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 kV All pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 kV Charged-device model (see Note 3): All pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV Continuous power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Power Dissipation Rating Table Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential I/O bus voltages, are with respect to GND, and are steady-state (unless otherwise specified). 2. Tested in accordance with JEDEC Standard 22, Test Method A114-A. 3. Tested in accordance with JEDEC Standard 22, Test Method C101. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING D 1080 mW 8.7 mW/C 690 mW 560 mW N 1150 mW 9.2 mW/C 736 mW 598 mW This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. recommended operating conditions Supply voltage, VCC Voltage at any bus terminal High-level input voltage, VIH Low-level input voltage, VIL Output current Operating free-air temperature, TA A, B G, G MIN NOM MAX UNIT 4.75 5 5.25 V -7 12 V 2 VCC 0.8 V 0 Y -8 8 SN75LBC173A 0 70 SN65LBC173A -40 85 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 mA C 3 SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 electrical characteristics over recommended operating conditions PARAMETER TEST CONDITIONS VIT+ VIT- Positive-going differential input voltage threshold VHYS VIK Hysteresis voltage (VIT+ - VIT-) VOH High-level output voltage Negative-going differential input voltage threshold -7 V VCM 12 V (VCM = (VA + VB )/2) TYP MAX -80 -10 -200 -120 II = -18 mA VID = 200 mV, IOH = -8 mA -1.5 -0.8 2.7 4.8 mV V See Figure 1 VOL Low-level output voltage VID = -200 mV, IOL = 8 mA IOZ High-impedance-state output current VO = 0 V to VCC II Line input current Other input at 0 V, VCC = 0 V or 5 V IIH IIL High-level input current RI Input resistance ICC Supply current V 0.2 -1 VI = 12 V VI = -7 V 0.4 1 A, B inputs VID = 5 V No load A 0.9 mA -0.7 100 Enable inputs G, G UNIT mV 40 Input clamp voltage Low-level input current MIN A -100 A 12 k 20 A 11 16 mA TYP MAX G at 0 V, G at VCC G at VCC, G at 0 V All typical values are at VCC = 5 V and 25C. switching characteristics over recommended operating conditions PARAMETER TEST CONDITIONS MIN UNIT tr tf Output rise time 2 4 ns Output fall time 2 4 ns tPLH tPHL Propagation delay time, low-to-high level output 9 12 16 ns 9 12 16 ns tPZH tPHZ Propagation delay time, high-impedance to high-level output 27 38 ns tPZL tPLZ Propagation delay time, high-impedance to low level output tsk(p) tsk(o) Pulse skew (| (tPLH - tPHL) |) VID = -3 V to 3 V, See Figure 2 Propagation delay time, high-to-low level output Propagation delay time, high-level to high-impedance output Propagation delay time, low-level to high-impedance output See Figure 3 See Figure 4 Output skew (see Note 4) 7 16 ns 29 38 ns 12 16 ns 0.2 1 ns 2 ns tsk(pp) Part-to-part skew (see Note 5) 2 ns All typical values are at VCC = 5 V and 25C. NOTES: 4. Outputs skew (tsk(o)) is the magnitude of the time delay difference between the outputs of a single device with all of the inputs connected together. 5. Part-to-part skew (tsk(pp)) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same input signals, the same supply voltages, at the same temperature, and have identical packages and test circuits. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 PARAMETER MEASUREMENT INFORMATION VA IO VID VB VO Figure 1. Voltage and Current Definitions 50 Generator Input B A 3V 1.5 V Y 1.5 V Input A B 0V tPLH CL = 15 pF (Includes Probe and Jig Capacitance) 50 Generator tPHL 1.5 V Output Y 90% 10% tr VOH 90% 10% VOL tf Generators: PRR = 1 MHz, 50% Duty Cycle, tr <6 ns, Zo = 50 Figure 2. Switching Test Circuit and Waveforms VCC 1.5 V A 1 k Y B CL = 15 pF (Includes Probe and Jig Capacitance) 3V G 1.5 V 0V tPHZ tPZH G Generator 50 G Y VCC 1.5 V 1.5 V VOH VOH -0.5 V GND Generators: PRR = 1 MHz, 50% Duty Cycle, tr <6 ns, Zo = 50 Figure 3. Test Circuit Waveforms, tPZH and tPHZ POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 PARAMETER MEASUREMENT INFORMATION VCC A -1.5 V Y 1 k B CL = 15 pF (Includes Probe and Jig Capacitance) 3V G 1.5 V 1.5 V 0V tPLZ tPZL G Generator 50 VCC G Y 1.5 V VCC VOL + 0.5 V VOL Generators: PRR = 1 MHz, 50% Duty Cycle, tr <6 ns, Zo = 50 Figure 4. Test Circuit Waveforms, tPZL and tPLZ 100 VTEST 0V Pulse Generator, 15 s Duration, 1% Duty Cycle 15 s 1.5 ms Figure 5. Test Circuit and Waveform, Transient Over-Voltage Test 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 VTEST SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 TYPICAL CHARACTERISTICS BUS INPUT CURRENT vs BUS INPUT VOLTAGE OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 800 6 VCC = 5 V TA = 25C 600 5 400 VO - Output Voltage - V Bus Input Current - A VCC = 0 V VCC = 5 V 200 0 -200 VIC = -7 V VIC = 0 V VIC = 12 V 4 VIC = -7 V VIC = 0 V VIC = 12 V 3 2 1 -400 -600 -10 -5 0 5 10 0 -150 15 -100 Bus Input Voltage - V -50 0 50 Differential Input Voltage - mV Figure 6 Figure 7 SUPPLY CURRENT vs SIGNALING RATE (ALL FOUR CHANNELS) PROPAGATION DELAY TIME vs FREE-AIR TEMPERATURE 60 13.5 Propagation Delay Time - ns I CC - Supply Current - mA 50 40 VCC = 5.25 V, CL = 15 pF 30 VCC = 5 V, CL = 15 pF VCC = 4.75 V, CL = 15 pF 20 10 13 tPLH 12.5 tPHL 12 11.5 VCC = 5 V, No Load 0 1 10 100 Signaling Rate (All Four Channels) - Mbps 11 -40 -20 0 20 40 60 80 TA - Free-Air Temperature - C Figure 8 Figure 9 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 TYPICAL CHARACTERISTICS 500 mV A, B -500 mV 20 ns 5V Y 0V Figure 10. Receiver Inputs and Outputs, 50 Mbps Signaling Rate 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLLS456B - NOVEMBER 2000 - REVISED APRIL 2005 APPLICATION INFORMATION TMS320F243 DSP (Controller) SN65LBC174A SN65LBC173A SPISIMO TMS320F241 DSP (Embedded Application) SPISIMO IOPA1 (Enable) SPISTE SPISTE IOPA1 IOPA2 SPICLK SPICLK IOPA2 (Enable) IOPA0 (Handshake /Status) IOPA0 SPISOMI SPISOMI Figure 11. Typical Application Circuit, DSP-to-DSP Link via Serial Peripheral Interface Motion Controller Servo Drive SN65LBC173A Encoder Phase A Encoder Phase B Encoder Index Status Bit Figure 12. Typical Application Circuit, High-Speed Servomotor Encoder Interface POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) SN65LBC173AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 65LBC173A SN65LBC173ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 65LBC173A SN65LBC173ADR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 65LBC173A SN65LBC173ADRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 65LBC173A SN65LBC173AN ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 65LBC173A SN65LBC173ANE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type -40 to 85 65LBC173A SN75LBC173AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 75LBC173A SN75LBC173ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 75LBC173A SN75LBC173ADR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 75LBC173A SN75LBC173ADRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 75LBC173A SN75LBC173AN ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 75LBC173A SN75LBC173ANE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 75LBC173A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN65LBC173ADR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN75LBC173ADR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65LBC173ADR SOIC D 16 2500 333.2 345.9 28.6 SN75LBC173ADR SOIC D 16 2500 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated