Z01 Standard 1A Triacs Features A2 On-state rms current, IT(RMS) 1 A Repetitive peak off-state voltage, VDRM/VRRM 600 or 800 V G A1 A2 Triggering gate current, IGT (Q1) 3 to 25 mA Description G The Z01 series is suitable for general purpose AC switching applications. These devices are typically used in applications such as home appliances (electrovalve, pump, door lock, small lamp control), fan speed controllers,... A2 A1 TO-92 Z01xxA G A2 A1 SOT-223 Z01xxN Different gate current sensitivities are available, allowing optimized performance when driven directly through microcontrollers. October 2010 Doc ID 7474 Rev 9 1/11 www.st.com 11 Characteristics 1 Z01 Characteristics Table 1. Absolute maximum ratings Symbol IT(RMS) ITSM I t Parameter On-state rms current (full sine wave) SOT-223 Ttab = 90 C TO-92 TL = 50 C Non repetitive surge peak on-state current (full cycle, Tj initial = 25 C) F = 50 Hz t = 20 ms F = 60 Hz t = 16.7 ms It Value for fusing tp = 10 ms Value Unit 1 A 8 A 8.5 0.35 As dI/dt Critical rate of rise of on-state current F = 120 Hz IG = 2 x IGT , tr 100 ns Tj = 125 C 20 A/s IGM Peak gate current Tj = 125 C 1 A Tj = 125 C 1 W - 40 to + 150 - 40 to + 125 C PG(AV) Tstg Tj Table 2. tp = 20 s Average gate power dissipation Storage junction temperature range Operating junction temperature range Electrical characteristics (Tj = 25 C, unless otherwise specified) Z01 Symbol IGT (1) Test conditions Quadrant Unit I - II - III VD = 12 V, RL = 30 VGT VGD VD = VDRM, RL = 3.3 k, Tj = 125 C IH (2) IT = 50 mA IL IG = 1.2 IGT IV 09 10 3 5 10 25 5 7 10 25 mA ALL MAX. 1.3 V ALL MIN. 0.2 V MAX. 7 10 10 25 7 10 15 25 15 20 25 50 MIN. 10 20 50 100 V/s MIN. 0.5 1 2 5 V/s MAX. II VD = 67% VDRM gate open Tj = 110 C (dV/dt)c (dI/dt)c = 0.44 A/ms, (2) Tj = 110 C 1. Minimum IGT is guaranteed at 5% of IGT max. 2. For both polarities of A2 referenced to A1. 2/11 07 MAX. I - III - IV dV/dt (2) 03 Doc ID 7474 Rev 9 mA mA Z01 Characteristics Table 3. Static characteristics Symbol VTM(1) Test conditions Value Unit ITM = 1.4 A, tp = 380 s Tj = 25 C MAX. 1.6 V Vto (1) Threshold voltage Tj = 125 C MAX. 0.95 V Rd (1) Dynamic resistance Tj = 125 C MAX. 400 m 5 A 0.5 mA Value Unit SOT-223 25 C/W TO-92 60 C/W SOT-223 60 C/W TO-92 150 IDRM IRRM Tj = 25 C VDRM = VRRM MAX. Tj = 125 C 1. For both polarities of A2 referenced to A1. Table 4. Thermal resistances Symbol Parameter Rth(j-t) Junction to tab (AC) Rth(j-I) Junction to lead (AC) S(1) Rth(j-a) =5 cm Junction to ambient 1. S = copper surface under tab. Figure 1. Maximum power dissipation versus on-state rms current (full cycle) Figure 2. On-state rms current versus lead (TO-92) or tab (SOT-223) temperature (full cycle) IT(RMS)(A) P(W) 1.50 1.2 1.25 1.0 1.00 0.8 0.75 0.6 0.50 0.4 Rth(j-a) = Rth(j-t) (SOT-223) Rth(j-a) = Rth(j-l) (TO-92) 0.25 0.2 IT(RMS)(A) Tl or Ttab(C) 0.00 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 Doc ID 7474 Rev 9 25 50 75 100 125 3/11 Characteristics Figure 3. Z01 On-state rms current versus ambient temperature (full cycle) Figure 4. IT(RMS)(A) Relative variation of thermal impedance versus pulse duration K=[Zth(j-a)/Rth(j-a)] 1.2 1.00 1.0 Rth(j-a) = 60C/W (SOT-223) 0.8 Z01xxA 0.6 0.10 Z01xxN Rth(j-a) = 150C/W (TO-92) 0.4 0.2 tp(s) Tamb (C) 0.0 0 25 Figure 5. 50 75 100 125 0.01 1E-3 1E-2 Relative variation of holding Figure 6. current and latching current versus junction temperature (typ. values) 1E-1 1E+0 1E+1 1E+2 5E+2 Surge peak on-state current versus number of cycles ITSM (A) IGT, IH, IL [Tj] / IGT, IH, IL [Tj=25C] 9 2.5 8 t=20ms 7 2.0 One cycle Non repetitive Tj initial = 25C 6 1.5 5 IGT 4 IH & IL 1.0 Repetitive Tamb = 25C 3 2 0.5 1 Tj (C) 0.0 -40 -20 Figure 7. 0 20 40 60 Number of cycles 0 80 100 120 1 140 10 Non-repetitive surge peak Figure 8. on-state current and corresponding value of I2t sinusoidal pulse width ITSM (A), I2t (A2s) 100 1000 On-state characteristics (maximum values) ITM(A) 10.0 100.0 Tj initial = 25C dI/dt limitation: 20A/s ITSM 10.0 Tj = Tjmax. 2 width tp <10 ms and corresponding value of I t 1.0 1.0 I2t 0.1 0.01 tp (ms) 0.10 VTM (V) 1.00 10.00 0.1 0.0 4/11 Tj=max. Vt0=0.95 V Rd=400 m Tj = 25C Doc ID 7474 Rev 9 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Z01 Characteristics Figure 9. Relative variation of critical rate Figure 10. Relative variation of critical rate of of decrease of main current versus decrease of main current versus junction temperature (dV/dt)c (typical valuues) (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 (dI/dt)c [Tj] / (dI/dt)c [Tj Specified] 6 5 4 3 2 Z0109 Z0103 Z0107 1 Z0110 Tj (C) (dV/dt)c (V/s) 0 0.1 1.0 10.0 100.0 0 25 50 75 100 125 Figure 11. SOT-223 thermal resistance junction to ambient versus copper surface under case (printed circuit board FR4, copper thickness; 35 m) Rth(j-a)(C/W) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 S(cm) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Doc ID 7474 Rev 9 3.5 4.0 4.5 5.0 5/11 Ordering information 2 Z01 Ordering information Figure 12. Ordering information scheme Z 01 03 M A [BLANK] 1AA2 Triac series Current 01 = 1 A Sensitivity 03 = 3 mA 07 = 5 mA 09 = 10 mA 10 = 25 mA Voltage M = 600 V N = 800 V Package A = TO-92 N = SOT-223 UF = SMBF3L Packing mode 1AA2 = TO-92 bulk (preferred) 2AL2 = TO-92 ammopack 5AL2 = TO-92 tape and reel 5AA4 = SOT-223 tape and reel 7" 6AA4 = SOT-223 tape and reel 13" 6/11 Doc ID 7474 Rev 9 Z01 Ordering information Table 5. Product Selector Voltage Part Number 600 V Z0103MA X Z0103MN X 700 V Sensitivity Type Package 3 mA Standard TO-92 800 V 3 mA Standard SOT-223 Z0103SA X 3 mA Standard TO-92 Z0103SN X 3 mA Standard SOT-223 3 mA Standard TO-92 Z0103NA X Z0103NN 3 mA Standard SOT-223 Z0107MA X X 5 mA Standard TO-92 Z0107MN X 5 mA Standard SOT-223 5 mA Standard TO-92 Z0107SA X Z0107SN X 5 mA Standard SOT-223 Z0107NA X 5 mA Standard TO-92 Z0107NN X 5 mA Standard SOT-223 10 mA Standard TO-92 Z0109MA X Z0109MN X 10 mA Standard SOT-223 Z0109SA X 10 mA Standard TO-92 Z0109SN X 10 mA Standard SOT-223 10 mA Standard TO-92 Z0109NA X Z0109NN 10 mA Standard SOT-223 Z0110MA X X 25 mA Standard TO-92 Z0110MN X 25 mA Standard SOT-223 25 mA Standard TO-92 Z0110SA X Z0110SN X 25 mA Standard SOT-223 Z0110NA X 25 mA Standard TO-92 Z0110NN X 25 mA Standard SOT-223 Doc ID 7474 Rev 9 7/11 Packaging information 3 Z01 Packaging information Epoxy meets UL94, V0 Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Table 6. SOT-223 dimensions Dimensions Ref. V A A1 c B Millimeters Min. Typ. A Inches Max. Min. Typ. Max. 1.80 0.071 0.02 0.10 0.001 0.004 0.60 0.70 0.85 0.024 0.027 0.033 B1 2.90 3.00 3.15 0.114 0.118 0.124 c 0.24 0.26 0.35 0.009 0.010 0.014 D(1) 6.30 6.50 6.70 0.248 0.256 0.264 e1 A1 D B B1 4 H E 1 2 3 e e 2.3 0.090 e1 4.6 0.181 (1) 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 E V 10 max 1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches) Figure 13. SOT-223 footprint dimensions (in millimeters) 3.25 1.32 5.16 7.80 1.32 2.30 8/11 Doc ID 7474 Rev 9 0.95 Z01 Packaging information Table 7. TO-92 dimensions Dimensions REF. Millimeters Min. Typ. Max. Inches Min. Typ. Max. A a B A 1.35 B C 4.70 C F D E 0.053 0.185 2.54 0.100 D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 Doc ID 7474 Rev 9 9/11 Ordering information 4 Z01 Ordering information Table 8. Ordering information Order code(1) Marking(1) Z01xxyA 1AA2 Z01xxyA Z01xxyA 2AL2 Z01xxyA Package TO-92 Weight Base quantity Delivery mode 2500 Bulk 0.2 g Ammopack 2000 Z01xxyA 5AL2 Z01xxyA Z0103yN 5AA4 Z3y Z0107yN 5AA4 Z7y Z0109yN 5AA4 Z9y Z0103yN 6AA4 Z3y Z0107yN 6AA4 Z7y Z0109yN 6AA4 Z9y Tape and reel SOT-223 1000 Tape and reel 7" 4000 Tape and reel 13" 0.12 g 1. xx = sensitivity, y = voltage 5 Revision history Table 9. 10/11 Document revision history Date Revision Changes Oct-2001 4 Last update. 10-Feb-2005 5 Package: TO-92 tape and reel delivery mode 5AL2 added. 09-May-2005 6 Table 4 on page 2: typo. mistake corrected 1. (dV/dt)c instead of (dI/dt)c 2. V/s unit instead of A/ms 21-Apr-2006 7 Reformatted to current standard. Table 2 on page 2: Typo corrected. Values for IGT split into two separate rows. 10-Oct-2006 8 Table 2: modified test conditions for (dV/dt)c. Changed "ambient" to "lead or tab" in Figure 2. 20-Oct-2010 9 Package: SOT-223 13" tape and reel added = 6AA4 Doc ID 7474 Rev 9 Z01 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 7474 Rev 9 11/11