MMBT2222ATT1-D - ON Semiconductor

 Semiconductor Components Industries, LLC, 2001

April, 2000 – Rev. 1 1Publication Order Number:

MMBT2222ATT1/D

MMBT2222ATT1

Preferred Device

General Purpose Transistor

NPN Silicon

These transistors are designed for general purpose amplifier

applications. They are housed in the SOT–416/SC–75 package which

is designed for low power surface mount applications.

MAXIMUM RATINGS (TA = 25°C)

Rating Symbol Max Unit

Collector–Emitter Voltage VCEO 40 Vdc

Collector–Base Voltage VCBO 75 Vdc

Emitter–Base Voltage VEBO 6.0 Vdc

Collector Current – Continuous IC600 mAdc

THERMAL CHARACTERISTICS

Characteristic Symbol Max Unit

Total Device Dissipation, (1)

TA = 25°CPD150 mW

Thermal Resistance,

Junction to Ambient RθJA 833 °C/W

Operating and Storage Junction

Temperature Range TJ, Tstg –55 to

+150 °C

(1) Device mounted on FR–4 glass epoxy printed circuit board using the

minimum recommended footpad.

Device Package Shipping

ORDERING INFORMATION

MMBT2222ATT1 SOT–416

http://onsemi.com

CASE 463

SOT–416/SC–75

STYLE 1

3000 / Tape & Reel

DEVICE MARKING

Preferred devices are recommended choices for future use

and best overall value.

COLLECTOR

BASE

EMITTER

MMBT2222ATT1

http://onsemi.com

ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)

Characteristic Symbol Min Max Unit

OFF CHARACTERISTICS

Collector–Emitter Breakdown Voltage(1)

(IC = 1.0 mAdc, IB = 0) V(BR)CEO 40 — Vdc

Collector–Base Breakdown Voltage

(IC = 10 Adc, IE = 0) V(BR)CBO 75 — Vdc

Emitter–Base Breakdown Voltage

(IE = 10 Adc, IC = 0) V(BR)EBO 6.0 — Vdc

Base Cutoff Current

(VCE = 60 Vdc, VEB = 3.0 Vdc) IBL — 20 nAdc

Collector Cutoff Current

(VCE = 60 Vdc, VEB = 3.0 Vdc) ICEX — 10 nAdc

ON CHARACTERISTICS(1)

DC Current Gain (1)

(IC = 0.1 mAdc, VCE = 10 Vdc)

(IC = 1.0 mAdc, VCE = 10 Vdc)

(IC = 10 mAdc, VCE = 10 Vdc)

(IC = 150 mAdc, VCE = 10 Vdc)

(IC = 500 mAdc, VCE = 10 Vdc)

HFE 35

100

—

Collector–Emitter Saturation Voltage(1)

(IC = 150 mAdc, IB = 15 mAdc)

(IC = 500 mAdc, IB = 50 mAdc)

VCE(sat) —

—0.3

1.0

Vdc

Base–Emitter Saturation Voltage(1)

(IC = 150 mAdc, IB = 15 mAdc)

(IC = 500 mAdc, IB = 50 mAdc)

VBE(sat) 0.6

—1.2

2.0

Vdc

SMALL–SIGNAL CHARACTERISTICS

Current–Gain — Bandwidth Product

(IC = 20 mAdc, VCE = 20 Vdc, f = 100 MHz) fT300 — MHz

Output Capacitance

(VCB = 10 Vdc, IE = 0, f = 1.0 MHz) Cobo — 8.0 pF

Input Capacitance

(VEB = 0.5 Vdc, IC = 0, f = 1.0 MHz) Cibo — 30 pF

Input Impedance

(VCE = 10 Vdc, IC = 10 mAdc, f = 1.0 kHz) hie 0.25 1.25 k ohms

Voltage Feedback Ratio

(VCE = 10 Vdc, IC = 10 mAdc, f = 1.0 kHz) hre — 4.0 X 10–4

Small–Signal Current Gain

(VCE = 10 Vdc, IC = 10 mAdc, f = 1.0 kHz) hfe 75 375 —

Output Admittance

(VCE = 10 Vdc, IC = 10 mAdc, f = 1.0 kHz) hoe 25 200 mhos

Noise Figure

(VCE = 10 Vdc, IC = 100 Adc, RS = 1.0 k ohms, f = 1.0 kHz) NF — 4.0 dB

SWITCHING CHARACTERISTICS

Delay Time (VCC = 3.0 Vdc, VBE = –0.5 Vdc, td— 10

Rise Time

(VCC

Vdc

VBE

Vdc

IC = 150 mAdc, IB1 = 15 mAdc) tr— 25 ns

Storage Time (VCC = 30 Vdc, IC = 150 mAdc, ts— 225

Fall Time

(VCC

Vdc

150

mAdc

IB1 = IB2 = 15 mAdc) tf— 60 ns

1. Pulse Test: Pulse Width  300 s, Duty Cycle  2.0%.

MMBT2222ATT1

http://onsemi.com

Figure 1. Turn–On Time Figure 2. Turn–Off Time

SWITCHING TIME EQUIVALENT TEST CIRCUITS

Scope rise time < 4 ns

*Total shunt capacitance of test jig, connectors, and oscilloscope.

+16 V

-2 V < 2 ns

1.0 to 100 µs,

DUTY CYCLE ≈ 2.0%

1 kΩ

+30 V

200

CS* < 10 pF

+16 V

-14 V

< 20 ns

1.0 to 100 µs,

DUTY CYCLE ≈ 2.0%

1 k

+30 V

200

CS* < 10 pF

-4 V

1N914

1000

100

200

300

500

700

1.0 k0.1 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 30 50 70 100 200 300 500 700

IC, COLLECTOR CURRENT (mA)

Figure 3. DC Current Gain

hFE, DC CURRENT GAINVCE, COLLECTOR-EMITTER VOLTAGE (VOLTS)

1.0

0.8

0.6

0.4

0.2

0.005 0.01 0.02 0.03 0.05 0.1 0.2 0.3 0.5 1.0 2.0 3.0 5.0 10 20 30 50

IB, BASE CURRENT (mA)

Figure 4. Collector Saturation Region

MMBT2222ATT1

http://onsemi.com

Figure 5. Turn–On Time

IC, COLLECTOR CURRENT (mA)

100

200

t, TIME (ns)

10 20 70

5.0

100

5.0 7.0 30 50 200

7.0

IC/IB = 10

TJ = 25°C

tr @ VCC = 30 V

td @ VEB(off) = 2.0 V

td @ VEB(off) = 0

3.0

2.0

300 500

500

t, TIME (ns)

5.0

7.0

100

200

300

Figure 6. Turn–Off Time

IC, COLLECTOR CURRENT (mA)

10 20 70 1005.0 7.0 30 50 200 300 500

VCC = 30 V

IC/IB = 10

IB1 = IB2

TJ = 25°C

t′s = ts - 1/8 tf

Figure 7. Frequency Effects

f, FREQUENCY (kHz)

4.0

6.0

8.0

2.0

0.1

Figure 8. Source Resistance Effects

RS, SOURCE RESISTANCE (OHMS)

NF, NOISE FIGURE (dB)

1.0 2.0 5.0 10 20 50

0.2 0.5

100

NF, NOISE FIGURE (dB)

0.01 0.02 0.05

RS = OPTIMUM

RS = SOURCE

RS = RESISTANCE

IC = 1.0 mA, RS = 150 Ω

500 µA, RS = 200 Ω

100 µA, RS = 2.0 kΩ

50 µA, RS = 4.0 kΩ

f = 1.0 kHz

IC = 50 µA

100 µA

500 µA

1.0 mA

4.0

6.0

8.0

2.0

50 100 200 500 1.0 k 2.0 k 5.0 k 10 k 20 k 50 k 100 k

Figure 9. Capacitances

REVERSE VOLTAGE (VOLTS)

3.0

5.0

7.0

2.0

0.1

CAPACITANCE (pF)

1.0 2.0 3.0 5.0 7.0 10 20 30 50

0.2 0.3 0.5 0.7

Ccb

Ceb

Figure 10. Current–Gain Bandwidth Product

IC, COLLECTOR CURRENT (mA)

100

200

300

500

fT, CURRENT-GAIN BANDWIDTH PRODUCT (MHz)

1.0 2.0 3.0 5.0 7.0 10 20 30 50 70 100

VCE = 20 V

TJ = 25°C

MMBT2222ATT1

http://onsemi.com

Figure 11. “On” Voltages

IC, COLLECTOR CURRENT (mA)

0.4

0.6

0.8

1.0

0.2

V, VOLTAGE (VOLTS)

TJ = 25°C

VBE(sat) @ IC/IB = 10

VCE(sat) @ IC/IB = 10

VBE(on) @ VCE = 10 V

Figure 12. Temperature Coefficients

IC, COLLECTOR CURRENT (mA)

-0.5

+0.5

COEFFICIENT (mV/ C)

-1.0

-1.5

-2.5

RVC for VCE(sat)

RVB for VBE

0.1 1.0 2.0 5.0 10 20 50

0.2 0.5 100 200 500 1.0 k

1.0 V

-2.0

0.1 1.0 2.0 5.0 10 20 500.2 0.5 100 200 500

MMBT2222ATT1

http://onsemi.com

ÉÉÉ

1.4

0.5 min. (3x)

TYPICAL

0.5

SOLDERING PATTERN

Unit: mm

PD = TJ(max) – TA

RθJA

PD = 150°C – 25°C

833°C/W = 150 milliwatts

•The soldering temperature and time should not exceed

260°C for more than 10 seconds.

•When shifting from preheating to soldering, the

maximum temperature gradient should be 5°C or less.

•After soldering has been completed, the device should

be allowed to cool naturally for at least three minutes.

Gradual cooling should be used as the use of forced

cooling will increase the temperature gradient and

result in latent failure due to mechanical stress.

•Mechanical stress or shock should not be applied dur-

ing cooling

* Soldering a device without preheating can cause exces-

sive thermal shock and stress which can result in damage

to the device.

INFORMATION FOR USING THE SOT–416 SURFACE MOUNT PACKAGE

MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS

Surface mount board layout is a critical portion of the total

design. The footprint for the semiconductor packages must

be the correct size to insure proper solder connection

SOT–416/SC–90 POWER DISSIPATION

The power dissipation of the SOT–416/SC–90 is a func-

tion of the pad size. This can vary from the minimum pad

size for soldering to the pad size given for maximum power

dissipation. Power dissipation for a surface mount device

is determined by TJ(max), the maximum rated junction tem-

perature of the die, RθJA, the thermal resistance from the

device junction to ambient; and the operating temperature,

TA. Using the values provided on the data sheet, PD can be

calculated as follows.

The values for the equation are found in the maximum

ratings table on the data sheet. Substituting these values into

the equation for an ambient temperature TA of 25°C, one

can calculate the power dissipation of the device which in

this case is 125 milliwatts.

The 833°C/W assumes the use of the recommended foot-

print on a glass epoxy printed circuit board to achieve a

power dissipation of 150 milliwatts. Another alternative

would be to use a ceramic substrate or an aluminum core

board such as Thermal Clad. Using a board material such

as Thermal Clad, a higher power dissipation can be

achieved using the same footprint.

interface between the board and the package. With the

correct pad geometry, the packages will self align when

subjected to a solder reflow process.

SOLDERING PRECAUTIONS

The melting temperature of solder is higher than the rated

temperature of the device. When the entire device is heated

to a high temperature, failure to complete soldering within

a short time could result in device failure. Therefore, the

following items should always be observed in order to

minimize the thermal stress to which the devices are

subjected.

•Always preheat the device.

•The delta temperature between the preheat and

soldering should be 100°C or less.*

•When preheating and soldering, the temperature of the

leads and the case must not exceed the maximum

temperature ratings as shown on the data sheet. When

using infrared heating with the reflow soldering

method, the difference should be a maximum of 10°C.

MMBT2222ATT1

http://onsemi.com

STEP 1

PREHEAT

ZONE 1

RAMP"

STEP 2

VENT

SOAK"

STEP 3

HEATING

ZONES 2 & 5

RAMP"

STEP 4

HEATING

ZONES 3 & 6

SOAK"

STEP 5

HEATING

ZONES 4 & 7

SPIKE"

STEP 6

VENT

STEP 7

COOLING

200°C

150°C

100°C

50°C

TIME (3 TO 7 MINUTES TOTAL) TMAX

SOLDER IS LIQUID FOR

40 TO 80 SECONDS

(DEPENDING ON

MASS OF ASSEMBLY)

205° TO 219°C

PEAK AT

SOLDER JOINT

DESIRED CURVE FOR LOW

MASS ASSEMBLIES

100°C

150°C

160°C

140°C

Figure 13. Typical Solder Heating Profile

DESIRED CURVE FOR HIGH

MASS ASSEMBLIES

170°C

For any given circuit board, there will be a group of

control settings that will give the desired heat pattern. The

operator must set temperatures for several heating zones,

and a figure for belt speed. Taken together, these control

settings make up a heating “profile” for that particular

circuit board. On machines controlled by a computer, the

computer remembers these profiles from one operating

session t o the next. Figure 7 shows a typical heating profile

for use when soldering a surface mount device to a printed

circuit board. This profile will vary among soldering

systems but it is a good starting point. Factors that can

affect the profile include the type of soldering system in

use, density and types of components on the board, type of

solder used, and the type of board or substrate material

being used. This profile shows temperature versus time.

SOLDER STENCIL GUIDELINES

Prior to placing surface mount components onto a printed

circuit board, solder paste must be applied to the pads. A

solder stencil is required to screen the optimum amount of

solder paste onto the footprint. The stencil is made of brass

or stainless steel with a typical thickness of 0.008 inches.

The stencil opening size for the surface mounted package

should be the same as the pad size on the printed circuit

board, i.e., a 1:1 registration.

TYPICAL SOLDER HEATING PROFILE

The line on the graph shows the actual temperature that

might be experienced on the surface of a test board at or

near a central solder joint. The two profiles are based on a

high density and a low density board. The Vitronics

SMD310 convection/infrared reflow soldering system was

used to generate this profile. The type of solder used was

62/36/2 Tin Lead Silver with a melting point between

177–189°C. When this type of furnace is used for solder

reflow work, the circuit boards and solder joints tend to

heat first. The components on the board are then heated by

conduction. The circuit board, because i t has a lar ge surface

area, absorbs the thermal energy more efficiently, then

distributes this energy to the components. Because of this

effect, the main body of a component may be up to 30

degrees cooler than the adjacent solder joints.

MMBT2222ATT1

http://onsemi.com

PACKAGE DIMENSIONS

SC–75 (SC–90, SOT–416)

CASE 463–01

ISSUE B

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A0.70 0.80 0.028 0.031

B1.40 1.80 0.055 0.071

C0.60 0.90 0.024 0.035

D0.15 0.30 0.006 0.012

G1.00 BSC 0.039 BSC

H--- 0.10 --- 0.004

J0.10 0.25 0.004 0.010

K1.45 1.75 0.057 0.069

L0.10 0.20 0.004 0.008

S0.50 BSC 0.020 BSC

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

0.20 (0.008) B

–A–

–B–

3 PL

0.20 (0.008) A

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes

without further notice to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular

purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,

including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be

validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.

SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or

death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold

SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable

attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim

alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION

JAPAN: ON Semiconductor, Japan Customer Focus Center

4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031

Phone: 81–3–5740–2700

Email: r14525@onsemi.com

ON Semiconductor Website: http://onsemi.com

For additional information, please contact your local

Sales Representative.

MMBT2222ATT1/D

Thermal Clad is a trademark of the Bergquist Company.

Literature Fulfillment:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada

Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada

Email: ONlit@hibbertco.com

N. American Technical Support: 800–282–9855 Toll Free USA/Canada