LM2743
LM2743 Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
Literature Number: SNVS276E
LM2743
January 6, 2011
Low Voltage N-Channel MOSFET Synchronous Buck
Regulator Controller
General Description
The LM2743 is a high-speed synchronous buck regulator
controller with an accurate feedback voltage accuracy of
±2%. It can provide simple down conversion to output volt-
ages as low as 0.6V. Though the control sections of the IC
are rated for 3 to 6V, the driver sections are designed to ac-
cept input supply rails as high as 16V. The use of adaptive
non-overlapping MOSFET gate drivers helps avoid potential
shoot-through problems while maintaining high efficiency.
The IC is designed for the more cost-effective option of driving
only N-channel MOSFETs in both the high-side and low-side
positions. It senses the low-side switch voltage drop for pro-
viding a simple, adjustable current limit.
The fixed-frequency voltage-mode PWM control architecture
is adjustable from 50 kHz to 1 MHz with one external resistor.
This wide range of switching frequency gives the power sup-
ply designer the flexibility to make better tradeoffs between
component size, cost and efficiency.
Features include soft-start, input under-voltage lockout (UV-
LO) and Power Good (based on both under-voltage and over-
voltage detection). In addition, the shutdown pin of the IC can
be used for providing startup delay, and the soft-start pin can
be used for implementing precise tracking, for the purpose of
sequencing with respect to an external rail.
Features
■Power stage input voltage from 1V to 16V
■Control stage input voltage from 3V to 6V
■Output voltage adjustable down to 0.6V
■Power good flag and shutdown
■Output over-voltage and under-voltage detection
■±2% feedback voltage accuracy over temperature
■Low-side adjustable current sensing
■Adjustable soft-start
■Tracking and sequencing with shutdown and soft-start
pins
■Switching frequency from 50 kHz to 1 MHz
■TSSOP-14 package
Applications
■3.3V Buck Regulation
■Cable Modem, DSL and ADSL
■Laser Jet and Ink Jet Printers
■Low Voltage Power Modules
■DSP, ASIC, Core and I/O
Typical Application
20095201
© 2011 National Semiconductor Corporation 200952 www.national.com
LM2743 Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
Connection Diagram
20095202
14-Lead Plastic TSSOP
θJA = 155°C/W
Ordering Information
Order Number Package Type NSC Package Drawing Supplied As
LM2743MTC TSSOP-14 MTC14 94 Units, Raill
LM2743MTCX TSSOP-14 MTC14 2500 Units on Tape and Reel
Pin Descriptions
BOOT (Pin 1) - Bootstrap pin. This is the supply rail for the
gate drivers. When the high-side MOSFET turns on, the volt-
age on this pin should be at least one gate threshold above
the regulator input voltage VIN to properly turn on the MOS-
FET. See MOSFET Gate Drivers in the Application Informa-
tion section for more details on how to select MOSFETs.
LG (Pin 2) - Low-gate drive pin. This is the gate drive for the
low-side N-channel MOSFET. This signal is interlocked with
the high-side gate drive HG (Pin 14), so as to avoid shoot-
through.
PGND (Pins 3, 13) - Power ground. This is also the ground
for the low-side MOSFET driver. Both the pins must be con-
nected together on the PCB and form a ground plane, which
is usually also the system ground.
SGND (Pin 4) - Signal ground. It should be connected ap-
propriately to the ground plane with due regard to good layout
practices in switching power regulator circuits.
VCC (Pin 5) Supply rail for the control sections of the IC.
PWGD (Pin 6) - Power Good pin. This is an open drain output,
which is typically meant to be connected to VCC or any other
low voltage source through a pull-up resistor. Choose the pull-
up resistor so that the current going into this pin is kept below
1 mA. For most applications a recommended value for the
pull-up resistor is 100 kΩ. The voltage on this pin is thus pulled
low under output under-voltage or over-voltage fault condi-
tions and also under input UVLO.
ISEN (Pin 7) - Current limit threshold setting pin. This sources
a fixed 40 µA current. A resistor of appropriate value should
be connected between this pin and the drain of the low-side
MOSFET (switch node).
EAO (Pin 8) - Output of the error amplifier. The voltage level
on this pin is compared with an internally generated ramp
signal to determine the duty cycle. This pin is necessary for
compensating the control loop.
SS/TRACK (Pin 9) - Soft-start and tracking pin. This pin is
internally connected to the non-inverting input of the error
amplifier during soft-start, and in fact any time the SS/TRACK
pin voltage happens to be below the internal reference volt-
age. For the basic soft-start function, a capacitor of minimum
value 1 nF is connected from this pin to ground. To track the
rising ramp of another power supply’s output, connect a re-
sistor divider from the output of that supply to this pin as
described in Application Information.
FB (Pin 10) - Feedback pin. This is the inverting input of the
error amplifier, which is used for sensing the output voltage
and compensating the control loop.
FREQ (Pin 11) - Frequency adjust pin. The switching fre-
quency is set by connecting a resistor of suitable value be-
tween this pin and ground. The equation for calculating the
exact value is provided in Application Information, but some
typical values (rounded up to the nearest standard values) are
324 kΩ for 100 kHz, 97.6 kΩ for 300 kHz, 56.2 kΩ for 500 kHz,
24.9 kΩ for 1 MHz.
SD (Pin 12) - IC shutdown pin. Pull this pin to VCC to ensure
the IC is enabled. Connect to ground to disable the IC. Under
shutdown, both high-side and low-side drives are off. This pin
also features a precision threshold for power supply sequenc-
ing purposes, as well as a low threshold to ensure minimal
quiescent current.
HG (Pin 14) - High-gate drive pin. This is the gate drive for
the high-side N-channel MOSFET. This signal is interlocked
with LG (Pin 2) to avoid shoot-through.
www.national.com 2
LM2743
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
VCC -0.3 to 7V
BOOT Voltage -0.3 to 21V
ISEN -0.3 to 9.5V
All other pins -0.3 to VCC + 0.3V
Junction Temperature 150°C
Storage Temperature −65°C to 150°C
Soldering Information
Lead Temperature
(soldering, 10sec) 260°C
Infrared or Convection (20sec) 235°C
ESD Rating (Note 3) 2 kV
Operating Ratings
Supply Voltage Range (VCC)3V to 6V
Junction Temperature Range (TJ)−40°C to +125°C
Thermal Resistance (θJA)155°C/W
Electrical Characteristics
VCC = 3.3V unless otherwise indicated. Typicals and limits appearing in plain type apply for TA= TJ= 25°C. Limits appearing in
boldface type apply over full Operating Temperature Range. Datasheet min/max specification limits are guaranteed by design,
test, or statistical analysis.
Symbol Parameter Conditions Min Typ Max Units
VFB FB Pin Voltage VCC = 3V to 6V 0.588 0.6 0.612 V
VON UVLO Thresholds Rising
Falling
2.76
2.42
V
IQ_VCC
Operating VCC Current
VCC = 3.3V, VSD = 3.3V
Fsw = 600kHz 1.0 1.5 2.1
mA
VCC = 5V, VSD = 3.3V
Fsw = 600kHz 1.0 1.7 2.1
Shutdown VCC Current VCC = 3.3V, VSD = 0V 110 185 µA
tPWGD1 PWGD Pin Response Time VFB Rising 6 µs
tPWGD2 PWGD Pin Response Time VFB Falling 6 µs
ISS-ON SS Pin Source Current VSS = 0V 710 14 µA
ISS-OC SS Pin Sink Current During Over
Current
VSS = 2.5V 90 µA
ISEN-TH ISEN Pin Source Current Trip Point 25 40 55 µA
ERROR AMPLIFIER
GBW Error Amplifier Unity Gain
Bandwidth
9 MHz
G Error Amplifier DC Gain 106 dB
SR Error Amplifier Slew Rate 3.2 V/µs
IEAO EAO Pin Current Sourcing and
Sinking Capability
VEAO = 1.5, FB = 0.55V
VEAO = 1.5, FB = 0.65V
2.6
9.2
mA
VEA Error Amplifier Output Voltage Minimum 1 V
Maximum 2 V
3 www.national.com
LM2743
Symbol Parameter Conditions Min Typ Max Units
GATE DRIVE
IQ-BOOT BOOT Pin Quiescent Current VBOOT = 12V, VSD = 0 18 90 µA
RHG_UP High-Side MOSFET Driver Pull-Up
ON resistance VBOOT = 5V @ 350mA Sourcing 3 Ω
RHG_DN High-Side MOSFET Driver Pull-
Down ON resistance HG = 5V @ 350mA Sourcing 2 Ω
RLG_UP Low-Side MOSFET Driver Pull-Up
ON resistance VBOOT = 5V @ 350mA Sourcing 3 Ω
RLG_DN Low-Side MOSFET Driver Pull-
Down ON resistance LG = 5V @ 350mA Sourcing 2 Ω
OSCILLATOR
fSW PWM Frequency
RFADJ = 702.1 kΩ 50
kHz
RFADJ = 98.74 kΩ 300
RFADJ = 45.74 kΩ475 600 725
RFADJ = 24.91 kΩ 1000
D Max High-Side Duty Cycle fSW = 300kHz
fSW = 600kHz
fSW = 1MHz
80
76
73
%
LOGIC INPUTS AND OUTPUTS
V STBY-IH Standby High Trip Point VFB = 0.575V, VBOOT = 3.3V, VSD
Rising
1.1 V
V STBY-IL Standby Low Trip Point VFB = 0.575V, VBOOT = 3.3V, VSD
Falling
0.232 V
V SD-IH SD Pin Logic High Trip Point VSD Rising 1.3 V
V SD-IL SD Pin Logic Low Trip Point VSD Falling 0.8 V
VPWGD-TH-LO PWGD Pin Trip Points FB Falling 0.408 0.434 0.457 V
VPWGD-TH-HI PWGD Pin Trip Points FB Rising 0.677 0.710 0.742 V
VPWGD-HYS PWGD Hysteresis FB Falling
FB Rising
60
90
mV
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device
operates correctly. Operating Ratings do not imply guaranteed performance limits.
Note 2: The power MOSFETs can run on a separate 1V to 16V rail (Input voltage, VIN). Practical lower limit of VIN depends on selection of the external MOSFET.
Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
www.national.com 4
LM2743
Typical Performance Characteristics
Efficiency (VOUT = 1.2V)
VCC = 3.3V, fSW = 300 kHz
20095240
Efficiency (VOUT = 2.5V)
VCC = 3.3V, fSW = 300 kHz
20095257
Efficiency (VOUT = 3.3V)
VCC = 5V, fSW = 300 kHz
20095241
VCC Operating Current plus BOOT Current vs Frequency
FDS6898A FET (TA = 25°C)
20095245
BOOT Pin Current vs Temperature for
BOOT Voltage = 3.3V
fSW = 300 kHz, FDS6898A FET, No-Load
20095242
BOOT Pin Current vs Temperature for
BOOT Voltage = 5V
fSW = 300 kHz, FDS6898A FET, No-Load
20095243
5 www.national.com
LM2743
BOOT Pin Current vs Temperature for
BOOT Voltage = 12V
fSW = 300 kHz, FDS6898A FET, No-Load
20095244
Internal Reference Voltage vs Temperature
20095258
Frequency vs Temperature
20095260
Output Voltage vs Output Current
20095256
Switch Waveforms (HG Rising)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
IOUT = 4A, CSS = 12nF, fSW = 300 kHz
20095246
Switch Waveforms (HG Falling)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
IOUT = 4A, CSS = 12nF, fSW = 300 kHz
20095247
www.national.com 6
LM2743
Start-Up (No-Load)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
CSS = 12nF, fSW = 300 kHz
20095248
Start-Up (Full-Load)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
IOUT = 4A, CSS = 12nF, fSW = 300 kHz
20095249
Shutdown (Full-Load)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
IOUT = 4A, CSS = 12nF, fSW = 300 kHz
20095250
Load Transient Response (IOUT = 0A to 4A)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
CSS = 12nF, fSW = 300 kHz
20095251
Load Transient Response (IOUT = 4A to 0A)
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
CSS = 12nF, fSW = 300 kHz
20095252
Load Transient Response
VCC = 3.3V, VIN = 5V, VOUT = 1.2V
CSS = 12nF, fSW = 300 kHz
20095253
7 www.national.com
LM2743
Line Transient Response (VIN = 3V to 9V)
VCC = 3.3V, VOUT = 1.2V
IOUT = 2A, fSW = 300 kHz
20095254
Line Transient Response (VIN = 9V to 3V)
VCC = 3.3V, VOUT = 1.2V
IOUT = 2A, fSW = 300 kHz
20095255
www.national.com 8
LM2743
Block Diagram
20095203
9 www.national.com
LM2743
Application Information
THEORY OF OPERATION
The LM2743 is a voltage-mode, high-speed synchronous
buck regulator with a PWM control scheme. It is designed for
use in set-top boxes, thin clients, DSL/Cable modems, and
other applications that require high efficiency buck convert-
ers. It has output shutdown (SD), input under-voltage lock-out
(UVLO) mode and power good (PWGD) flag (based on over-
voltage and under-voltage detection). The over-voltage and
under-voltage signals are logically OR'ed to drive the power
good signal and provide a logic signal to the system if the
output voltage goes out of regulation. Current limit is achieved
by sensing the voltage VDS across the low side MOSFET.
START UP/SOFT-START
When VCC exceeds 2.76V and the shutdown pin (SD) sees a
logic high, the soft-start period begins. Then an internal, fixed
10 µA source begins charging the soft-start capacitor. During
soft-start the voltage on the soft-start capacitor CSS is con-
nected internally to the non-inverting input of the error ampli-
fier. The soft-start period lasts until the voltage on the soft-
start capacitor exceeds the LM2743 reference voltage of
0.6V. At this point the reference voltage takes over at the non-
inverting error amplifier input. The capacitance of CSS deter-
mines the length of the soft-start period, and can be
approximated by:
Where CSS is in µF and tSS is in ms.
During soft start the Power Good flag is forced low and it is
released when the FB pin voltage reaches 70% of 0.6V. At
this point the chip enters normal operation mode, and the
output overvoltage and undervoltage monitoring starts.
NORMAL OPERATION
While in normal operation mode, the LM2743 regulates the
output voltage by controlling the duty cycle of the high side
and low side MOSFETs (see Typical Application Circuit). The
equation governing output voltage is:
The PWM frequency is adjustable between 50 kHz and 1 MHz
and is set by an external resistor, RFADJ, between the FREQ
pin and ground. The resistance needed for a desired frequen-
cy is approximately:
Where fSW is in Hz and RFADJ is in kΩ.
TRACKING A VOLTAGE LEVEL
The LM2743 can track the output of a master power supply
during soft-start by connecting a resistor divider to the SS/
TRACK pin. In this way, the output voltage slew rate of the
LM2743 will be controlled by the master supply for loads that
require precise sequencing. When the tracking function is
used no soft-start capacitor should be connected to the SS/
TRACK pin. Otherwise, a CSS value of at least 1 nF between
the soft-start pin and ground should be used.
20095207
FIGURE 1. Tracking Circuit
One way to use the tracking feature is to design the tracking
resistor divider so that the master supply’s output voltage
(VOUT1) and the LM2743’s output voltage (represented sym-
bolically in Figure 1 as VOUT2, i.e. without explicitly showing
the power components) both rise together and reach their
target values at the same time. For this case, the equation
governing the values of the tracking divider resistors RT1 and
RT2 is:
The current through RT1 should be about 3 mA to 4 mA for
precise tracking. The final voltage of the SS/TRACK pin
should be set higher than the feedback voltage of 0.6V (say
about 0.65V as in the above equation). If the master supply
voltage was 5V and the LM2743 output voltage was 1.8V, for
example, then the value of RT1 needed to give the two sup-
plies identical soft-start times would be 150Ω. A timing dia-
gram for the equal soft-start time case is shown in Figure 2.
www.national.com 10
LM2743
20095208
FIGURE 2. Tracking with Equal Soft-Start Time
TRACKING A VOLTAGE SLEW RATE
The tracking feature can alternatively be used not to make
both rails reach regulation at the same time but rather to have
similar rise rates (in terms of output dV/dt). This method en-
sures that the output voltage of the LM2743 always reaches
regulation before the output voltage of the master supply. Be-
cause the output of the master supply is divided down, in order
to track properly the output voltage of the LM2743 must be
lower than the voltage of the master supply. In this case, the
tracking resistors can be determined based on the following
equation:
For the example case of VOUT1 = 5V and VOUT2 = 1.8V, with
RT1 set to 150Ω as before, RT2 is calculated from the above
equation to be 265Ω. A timing diagram for the case of equal
slew rates is shown in Figure 3.
20095210
FIGURE 3. Tracking with Equal Slew Rates
SEQUENCING
The start up/soft-start of the LM2743 can be delayed for the
purpose of sequencing by connecting a resistor divider from
the output of a master power supply to the SD pin, as shown
in Figure 4.
20095214
FIGURE 4. Sequencing Circuit
A desired delay time tDELAY between the startup of the master
supply output voltage and the LM2743 output voltage can be
set based on the SD pin low-to-high threshold VSD-IH and the
slew rate of the voltage at the SD pin, SRSD:
tDELAY = VSD-IH / SRSD
Note again, that in Figure 4, the LM2743’s output voltage has
been represented symbolically as VOUT2, i.e. without explicitly
showing the power components.
VSD-IH is typically 1.08V and SRSD is the slew rate of the SD
pin voltage. The values of the sequencing divider resistors
RS1 and RS2 set the SRSD based on the master supply output
voltage slew rate, SROUT1, using the following equation:
For example, if the master supply output voltage slew rate
was 1V/ms and the desired delay time between the startup of
the master supply and LM2743 output voltage was 5ms, then
the desired SD pin slew rate would be (1.08V/5 ms) = 0.216V/
ms. Due to the internal impedance of the SD pin, the maxi-
mum recommended value for RS2 is 1kΩ. To achieve the
desired slew rate, RS1 would then be 274Ω. A timing diagram
for this example is shown in Figure 5.
11 www.national.com
LM2743
20095211
FIGURE 5. Delay for Sequencing
SD PIN IMPEDANCE
When connecting a resistor divider to the SD pin of the
LM2743 some care has to be taken. Once the SD voltage
goes above VSD-IH, a 17 µA pull-up current is activated as
shown in Figure 6. This current is used to create the internal
hysteresis (≊170 mV); however, high external impedances
will affect the SD pin logic thresholds as well. The external
impedance used for the sequencing divider network should
preferably be a small fraction of the impedance of the SD pin
for good performance (around 1kΩ).
20095206
FIGURE 6. SD Pin Logic
MOSFET GATE DRIVERS
The LM2743 has two gate drivers designed for driving N-
channel MOSFETs in a synchronous mode. Note that unlike
most other synchronous controllers, the bootstrap capacitor
of the LM2743 provides power not only to the driver of the
upper MOSFET, but the lower MOSFET driver too (both
drivers are ground referenced, i.e. no floating driver). To fully
turn the top MOSFET on, the BOOT voltage must be at least
one gate threshold greater than VIN when the high-side drive
goes high. This bootstrap voltage is usually supplied from a
local charge pump structure. But looking at the Typical Appli-
cation schematic, this also means that the difference voltage
VCC - VD1, which is the voltage the bootstrap capacitor
charges up to, must be always greater than the maximum tol-
erance limit of the threshold voltage of the upper MOSFET.
Here VD1 is the forward voltage drop across the bootstrap
diode D1. This therefore may place restrictions on the mini-
mum input voltage and/or type of MOSFET used.
The most basic charge bootstrap pump circuit can be built
using one Schottky diode and a small capacitor, as shown in
Figure 7. The capacitor CBOOT serves to maintain enough
voltage between the top MOSFET gate and source to control
the device even when the top MOSFET is on and its source
has risen up to the input voltage level. The charge pump cir-
cuitry is fed from VCC, which can operate over a range from
3.0V to 6.0V. Using this basic method the voltage applied to
the gates of both high-side and low-side MOSFETs is VCC -
VD. This method works well when VCC is 5V±10%, because
the gate drives will get at least 4.0V of drive voltage during
the worst case of VCC-MIN = 4.5V and VD-MAX = 0.5V. Logic
level MOSFETs generally specify their on-resistance at VGS
= 4.5V. When VCC = 3.3V±10%, the gate drive at worst case
could go as low as 2.5V. Logic level MOSFETs are not guar-
anteed to turn on, or may have much higher on-resistance at
2.5V. Sub-logic level MOSFETs, usually specified at VGS =
2.5V, will work, but are more expensive, and tend to have
higher on-resistance. The circuit in Figure 7 works well for
input voltages ranging from 1V up to 16V and VCC = 5V ±10%,
because the drive voltage depends only on VCC.
20095212
FIGURE 7. Basic Charge Pump (Bootstrap)
Note that the LM2743 can be paired with a low cost linear
regulator like the LM78L05 to run from a single input rail be-
tween 6.0 and 14V. The 5V output of the linear regulator
powers both the VCC and the bootstrap circuit, providing effi-
cient drive for logic level MOSFETs. An example of this circuit
is shown in Figure 8.
www.national.com 12
LM2743
20095213
FIGURE 8. LM78L05 Feeding Basic Charge Pump
Figure 9 shows a second possibility for bootstrapping the
MOSFET drives using a doubler. This circuit provides an
equal voltage drive of VCC - 3VD + VIN to both the high-side
and low-side MOSFET drives. This method should only be
used in circuits that use 3.3V for both VCC and VIN. Even with
VIN = VCC = 3.0V (10% lower tolerance on 3.3V) and VD = 0.5V
both high-side and low-side gates will have at least 4.5V of
drive. The power dissipation of the gate drive circuitry is di-
rectly proportional to gate drive voltage, hence the thermal
limits of the LM2743 IC will quickly be reached if this circuit is
used with VCC or VIN voltages over 5V.
20095219
FIGURE 9. Charge Pump with Added Gate Drive
All the gate drive circuits shown in the above figures typically
use 100 nF ceramic capacitors in the bootstrap locations.
POWER GOOD SIGNAL
The open drain output on the Power Good pin needs a pull-
up resistor to a low voltage source. The pull-up resistor should
be chosen so that the current going into the Power Good pin
is less than 1 mA. A 100 kΩ resistor is recommended for most
applications.
The Power Good signal is an OR-gated flag which takes into
account both output over-voltage and under-voltage condi-
tions. If the feedback pin (FB) voltage is 18% above its nom-
inal value (118% x VFB = 0.708V) or falls 28% below that value
(72 %x VFB = 0.42V) the Power Good flag goes low. The
Power Good flag can be used to signal other circuits that the
output voltage has fallen out of regulation, however the
switching of the LM2743 continues regardless of the state of
the Power Good signal. The Power Good flag will return to
logic high whenever the feedback pin voltage is between 72%
and 118% of 0.6V.
UVLO
The 2.76V turn-on threshold on VCC has a built in hysteresis
of about 300 mV. If VCC drops below 2.42V, the chip enters
UVLO mode. UVLO consists of turning off the top and bottom
MOSFETS and remaining in that condition until VCC rises
above 2.76V. As with shutdown, the soft-start capacitor is
discharged through an internal MOSFET, ensuring that the
next start-up will be controlled by the soft-start circuitry.
CURRENT LIMIT
Current limit is realized by sensing the voltage across the low-
side MOSFET while it is on. The RDS(ON) of the MOSFET is a
known value; hence the current through the MOSFET can be
determined as:
VDS = IOUT x RDS(ON)
The current through the low-side MOSFET while it is on is also
the falling portion of the inductor current. The current limit
threshold is determined by an external resistor, RCS, connect-
ed between the switching node and the ISEN pin. A constant
current of 40 µA is forced through RCS, causing a fixed voltage
drop. This fixed voltage is compared against VDS and if the
latter is higher, the current limit of the chip has been reached.
To obtain a more accurate value for RCS you must consider
the operating values of RDS(ON) and ISEN-TH at their operating
temperatures in your application and the effect of slight pa-
rameter differences from part to part. RCS can be found by
using the following equation using the RDS(ON) value of the low
side MOSFET at it's expected hot temperature and the abso-
lute minimum value expected over the full temperature range
for the for the ISEN-TH which is 25 µA:
RCS = RDSON-HOT x ILIM / 40 µA
For example, a conservative 15A current limit in a 10A design
with a minimum RDS(ON) of 10 mΩ would require a 6 kΩ re-
sistor. To prevent the ISEN pin from sinking too much current
when the switch node goes above 9.5V, the value of the cur-
rent limit setting resistor RCS should not be too low. The
criterion is as follows,
where the 10 mA is the maximum current ISEN pin is allowed
to sink. For example if VIN = 13.2V, the minimum value of
RCS is 370Ω. Because current sensing is done across the low-
side MOSFET, no minimum high-side on-time is necessary.
The LM2743 enters current limit mode if the inductor current
exceeds the current limit threshold at the point where the high-
side MOSFET turns off and the low-side MOSFET turns on.
(The point of peak inductor current, see Figure 10). Note that
in normal operation mode the high-side MOSFET always
13 www.national.com
LM2743
turns on at the beginning of a clock cycle. In current limit
mode, by contrast, the high-side MOSFET on-pulse is
skipped. This causes inductor current to fall. Unlike a normal
operation switching cycle, however, in a current limit mode
switching cycle the high-side MOSFET will turn on as soon as
inductor current has fallen to the current limit threshold. The
LM2743 will continue to skip high-side MOSFET pulses until
the inductor current peak is below the current limit threshold,
at which point the system resumes normal operation.
20095288
FIGURE 10. Current Limit Threshold
Unlike a high-side MOSFET current sensing scheme, which
limits the peaks of inductor current, low-side current sensing
is only allowed to limit the current during the converter off-
time, when inductor current is falling. Therefore in a typical
current limit plot the valleys are normally well defined, but the
peaks are variable, according to the duty cycle. The PWM
error amplifier and comparator control the off-pulse of the
high-side MOSFET, even during current limit mode, meaning
that peak inductor current can exceed the current limit thresh-
old. Assuming that the output inductor does not saturate, the
maximum peak inductor current during current limit mode can
be calculated with the following equation:
Where TSW is the inverse of switching frequency fSW. The 200
ns term represents the minimum off-time of the duty cycle,
which ensures enough time for correct operation of the cur-
rent sensing circuitry.
In order to minimize the time period in which peak inductor
current exceeds the current limit threshold, the IC also dis-
charges the soft-start capacitor through a fixed 90 µA sink.
The output of the LM2743 internal error amplifier is limited by
the voltage on the soft-start capacitor. Hence, discharging the
soft-start capacitor reduces the maximum duty cycle D of the
controller. During severe current limit this reduction in duty
cycle will reduce the output voltage if the current limit condi-
tions last for an extended time. Output inductor current will be
reduced in turn to a flat level equal to the current limit thresh-
old. The third benefit of the soft-start capacitor discharge is a
smooth, controlled ramp of output voltage when the current
limit condition is cleared.
FOLDBACK CURRENT LIMIT
In the case where extra protection is used to help an output
short condition, a current foldback resistor (RCLF) should be
considered, see Figure 11. First select the percentage of cur-
rent limit foldback (PLIM):
PLIM = ILIM x P
where P is a ratio between 0 and 1.
20095295
FIGURE 11. Foldback Current Limit Circuit
Obtain the RCS with the following equation:
where ISEN = 40 μA. If the switch node goes above 9.5V the
following criterion must be satisfied:
The equation for calculating the foldback resistance value is:
SHUTDOWN
If the shutdown pin is pulled low, (below 0.8V) the LM2743
enters shutdown mode, and discharges the soft-start capac-
itor through a MOSFET switch. The high and low-side MOS-
FETs are turned off. The LM2743 remains in this state as long
as VSD sees a logic low (see the Electrical Characteristics ta-
ble). To assure proper IC start-up the shutdown pin should
not be left floating. For normal operation this pin should be
connected directly to VCC or to another voltage between 1.3V
to VCC (see the Electrical Characteristics table).
DESIGN CONSIDERATIONS
The following is a design procedure for all the components
needed to create the Typical Application Circuit shown on the
front page. This design converts 3.3V (VIN) to 1.2V (VOUT) at
a maximum load of 4A with an efficiency of 89% and a switch-
ing frequency of 300 kHz. The same procedures can be
www.national.com 14
LM2743
followed to create many other designs with varying input volt-
ages, output voltages, and load currents.
Duty Cycle Calculation
The complete duty cycle for a buck converter is defined with
the following equation:
where VSWL and VSWH are the respective forward voltage
drops that develop across the low side and high side MOS-
FETs. Assuming the inductor ripple current is 20% to 30% of
the output current, therefore:
VSWL = IOUT x RDS(ON)LOW
(Low-Side MOSFET)
VSWH = IOUT x RDS(ON)HIGH
(High-Side MOSFET)
To calculate the maximum duty cycle use the estimated 'hot'
RDS(on) value of the MOSFETs, the minimum input voltage,
and maximum load. As shown in Figure 12, the worst case
maximum duty cycles of the LM2743 occurs at 125°C junction
temperature vs VCC (IC control section voltage). Ensure that
the operating duty cycle is below the curve in Figure 12, if this
condition is not satisfied, the system will be unable to develop
the required duty cycle to derive the necessary system power
and so the output voltage will fall out of regulation.
20095291
FIGURE 12. Maximum Duty Cycle vs VCC
TJ = 125°C
Input Capacitor
The input capacitors in a Buck converter are subjected to high
stress due to the input current trapezoidal waveform. Input
capacitors are selected for their ripple current capability and
their ability to withstand the heat generated since that ripple
current passes through their ESR. Input rms ripple current is
approximately:
The power dissipated by each input capacitor is:
where n is the number of capacitors, and ESR is the equiva-
lent series resistance of each capacitor. The equation above
indicates that power loss in each capacitor decreases rapidly
as the number of input capacitors increases. The worst-case
ripple for a Buck converter occurs during full load and when
the duty cycle (D) is 0.5. For this 3.3V to 1.2V design the duty
cycle is 0.364. For a 4A maximum load the ripple current is
1.92A.
Output Inductor
The output inductor forms the first half of the power stage in
a Buck converter. It is responsible for smoothing the square
wave created by the switching action and for controlling the
output current ripple (ΔIOUT). The inductance is chosen by
selecting between tradeoffs in efficiency and response time.
The smaller the output inductor, the more quickly the con-
verter can respond to transients in the load current. However,
as shown in the efficiency calculations, a smaller inductor re-
quires a higher switching frequency to maintain the same
level of output current ripple. An increase in frequency can
mean increasing loss in the MOSFETs due to the charging
and discharging of the gates. Generally the switching fre-
quency is chosen so that conduction loss outweighs switching
loss. The equation for output inductor selection is:
L = 1.6µH
Here we have plugged in the values for output current ripple,
input voltage, output voltage, switching frequency, and as-
sumed a 40% peak-to-peak output current ripple. This yields
an inductance of 1.6 µH. The output inductor must be rated
to handle the peak current (also equal to the peak switch cur-
rent), which is (IOUT + (0.5 x ΔIOUT)) = 4.8A, for a 4A design.
The Coilcraft DO3316P-222P is 2.2 µH, is rated to 7.4A peak,
and has a direct current resistance (DCR) of 12 mΩ.
After selecting an output inductor, inductor current ripple
should be re-calculated with the new inductance value, as this
information is needed to select the output capacitor. Re-ar-
ranging the equation used to select inductance yields the
following:
VIN(MAX) is assumed to be 10% above the steady state input
voltage, or 3.6V. The actual current ripple will then be 1.2A.
Peak inductor/switch current will be 4.6A.
Output Capacitor
The output capacitor forms the second half of the power stage
of a Buck switching converter. It is used to control the output
15 www.national.com
LM2743
voltage ripple (ΔVOUT) and to supply load current during fast
load transients.
In this example the output current is 4A and the expected type
of capacitor is an aluminum electrolytic, as with the input ca-
pacitors. Other possibilities include ceramic, tantalum, and
solid electrolyte capacitors, however the ceramic type often
do not have the large capacitance needed to supply current
for load transients, and tantalums tend to be more expensive
than aluminum electrolytic. Aluminum capacitors tend to have
very high capacitance and fairly low ESR, meaning that the
ESR zero, which affects system stability, will be much lower
than the switching frequency. The large capacitance means
that at the switching frequency, the ESR is dominant, hence
the type and number of output capacitors is selected on the
basis of ESR. One simple formula to find the maximum ESR
based on the desired output voltage ripple, ΔVOUT and the
designed output current ripple, ΔIOUT, is:
In this example, in order to maintain a 2% peak-to-peak output
voltage ripple and a 40% peak-to-peak inductor current ripple,
the required maximum ESR is 20 mΩ. The Sanyo 4SP560M
electrolytic capacitor will give an equivalent ESR of 14 mΩ.
The capacitance of 560 µF is enough to supply energy even
to meet severe load transient demands.
MOSFETs
Selection of the power MOSFETs is governed by a tradeoff
between cost, size, and efficiency. One method is to deter-
mine the maximum cost that can be endured, and then select
the most efficient device that fits that price. Breaking down the
losses in the high-side and low-side MOSFETs and then cre-
ating spreadsheets is one way to determine relative efficien-
cies between different MOSFETs. Good correlation between
the prediction and the bench result is not guaranteed, how-
ever. Single-channel buck regulators that use a controller IC
and discrete MOSFETs tend to be most efficient for output
currents of 2A to 10A.
Losses in the high-side MOSFET can be broken down into
conduction loss, gate charging loss, and switching loss. Con-
duction loss, or I2R loss, is approximately:
PC = D ((IO)2 x RDSON-HI x 1.3)
(High-Side MOSFET)
PC = (1 - D) x ((IO)2 x RDSON-LO x 1.3)
(Low-Side MOSFET)
In the above equations the factor 1.3 accounts for the in-
crease in MOSFET RDSON due to heating. Alternatively, the
1.3 can be ignored and the RDSON of the MOSFET estimated
using the RDSON Vs. Temperature curves in the MOSFET
datasheets.
Gate charging loss results from the current driving the gate
capacitance of the power MOSFETs, and is approximated as:
PGC = n x (VDD) x QG x fSW
where ‘n’ is the number of MOSFETs (if multiple devices have
been placed in parallel), VDD is the driving voltage (see MOS-
FET Gate Drivers section) and QGS is the gate charge of the
MOSFET. If different types of MOSFETs are used, the ‘n’ term
can be ignored and their gate charges simply summed to form
a cumulative QG. Gate charge loss differs from conduction
and switching losses in that the actual dissipation occurs in
the LM2743, and not in the MOSFET itself.
Switching loss occurs during the brief transition period as the
high-side MOSFET turns on and off, during which both current
and voltage are present in the channel of the MOSFET. It can
be approximated as:
PSW = 0.5 x VIN x IO x (tr + tf) x fSW
where tR and tF are the rise and fall times of the MOSFET.
Switching loss occurs in the high-side MOSFET only.
For this example, the maximum drain-to-source voltage ap-
plied to either MOSFET is 3.6V. The maximum drive voltage
at the gate of the high-side MOSFET is 3.1V, and the maxi-
mum drive voltage for the low-side MOSFET is 3.3V. Due to
the low drive voltages in this example, a MOSFET that turns
on fully with 3.1V of gate drive is needed. For designs of 5A
and under, dual MOSFETs in SO-8 package provide a good
trade-off between size, cost, and efficiency.
Support Components
CIN2 - A small value (0.1 µF to 1 µF) ceramic capacitor should
be placed as close as possible to the drain of the high-side
MOSFET and source of the low-side MOSFET (dual MOS-
FETs make this easy). This capacitor should be X5R type
dielectric or better.
RCC, CCC- These are standard filter components designed to
ensure smooth DC voltage for the chip supply. RCC should be
1Ω to 10Ω. CCC should 1 µF, X5R type or better.
CBOOT- Bootstrap capacitor, typically 100 nF.
RPULL-UP – This is a standard pull-up resistor for the open-
drain power good signal (PWGD). The recommended value
is 10 kΩ connected to VCC. If this feature is not necessary, the
resistor can be omitted.
D1 - A small Schottky diode should be used for the bootstrap.
It allows for a minimum drop for both high and low-side
drivers. The MBR0520 or BAT54 work well in most designs.
RCS - Resistor used to set the current limit. Since the design
calls for a peak current magnitude (IOUT+ (0.5 x ΔIOUT)) of
4.8A, a safe setting would be 6A. (This is below the saturation
current of the output inductor, which is 7A.) Following the
equation from the Current Limit section, a 1.3 kΩ resistor
should be used.
RFADJ - This resistor is used to set the switching frequency of
the chip. The resistor value is calculated from equation in
Normal Operation section. For 300 kHz operation, a 97.6
kΩ resistor should be used.
CSS - The soft-start capacitor depends on the user require-
ments and is calculated based on the equation given in the
section titled START UP/SOFT-START. Therefore, for a 700
μs delay, a 12 nF capacitor is suitable.
Control Loop Compensation
The LM2743 uses voltage-mode (‘VM’) PWM control to cor-
rect changes in output voltage due to line and load transients.
One of the attractive advantages of voltage mode control is
its relative immunity to noise and layout. However VM re-
quires careful small signal compensation of the control loop
for achieving high bandwidth and good phase margin.
The control loop is comprised of two parts. The first is the
power stage, which consists of the duty cycle modulator, out-
put inductor, output capacitor, and load. The second part is
the error amplifier, which for the LM2743 is a 9 MHz op-amp
used in the classic inverting configuration. Figure 13 shows
the regulator and control loop components.
www.national.com 16
LM2743
20095264
FIGURE 13. Power Stage and Error Amp
One popular method for selecting the compensation compo-
nents is to create Bode plots of gain and phase for the power
stage and error amplifier. Combined, they make the overall
bandwidth and phase margin of the regulator easy to see.
Software tools such as Excel, MathCAD, and Matlab are use-
ful for showing how changes in compensation or the power
stage affect system gain and phase.
The power stage modulator provides a DC gain ADC that is
equal to the input voltage divided by the peak-to-peak value
of the PWM ramp. This ramp is 1.0VP-P for the LM2743. The
inductor and output capacitor create a double pole at fre-
quency fDP, and the capacitor ESR and capacitance create a
single zero at frequency fESR. For this example, with VIN =
3.3V, these quantities are:
In the equation for fDP, the variable RL is the power stage re-
sistance, and represents the inductor DCR plus the on resis-
tance of the top power MOSFET. RO is the output voltage
divided by output current. The power stage transfer function
GPS is given by the following equation, and Figure 14 shows
Bode plots of the phase and gain in this example.
a = LCO(RO + RC)
b = L + CO(RORL + RORC + RCRL)
c = RO + RL
20095269
20095270
FIGURE 14. Power Stage Gain and Phase
The double pole at 4.5 kHz causes the phase to drop to ap-
proximately -130° at around 10 kHz. The ESR zero, at 20.3
kHz, provides a +90° boost that prevents the phase from
dropping to -180º. If this loop were left uncompensated, the
bandwidth would be approximately 10 kHz and the phase
margin 53°. In theory, the loop would be stable, but would
suffer from poor DC regulation (due to the low DC gain) and
would be slow to respond to load transients (due to the low
bandwidth.) In practice, the loop could easily become unsta-
ble due to tolerances in the output inductor, capacitor, or
changes in output current, or input voltage. Therefore, the
loop is compensated using the error amplifier and a few pas-
sive components.
For this example, a Type III, or three-pole-two-zero approach
gives optimal bandwidth and phase.
In most voltage mode compensation schemes, including
Type III, a single pole is placed at the origin to boost DC gain
as high as possible. Two zeroes fZ1 and fZ2 are placed at the
double pole frequency to cancel the double pole phase lag.
Then, a pole, fP1 is placed at the frequency of the ESR zero.
A final pole fP2 is placed at one-half of the switching frequency.
The gain of the error amplifier transfer function is selected to
give the best bandwidth possible without violating the Nyquist
stability criteria. In practice, a good crossover point is one-fifth
17 www.national.com
LM2743
of the switching frequency, or 60 kHz for this example. The
generic equation for the error amplifier transfer function is:
In this equation the variable AEA is a ratio of the values of the
capacitance and resistance of the compensation compo-
nents, arranged as shown in Figure 13. AEA is selected to
provide the desired bandwidth. A starting value of 80,000 for
AEA should give a conservative bandwidth. Increasing the
value will increase the bandwidth, but will also decrease
phase margin. Designs with 45° to 60° are usually best be-
cause they represent a good trade-off between bandwidth
and phase margin. In general, phase margin is lowest and
gain highest (worst-case) for maximum input voltage and
minimum output current. One method to select AEA is to use
an iterative process beginning with these worst-case condi-
tions.
1. Increase AEA
2. Check overall bandwidth and phase margin
3. Change VIN to minimum and recheck overall bandwidth
and phase margin
4. Change IO to maximum and recheck overall bandwidth
and phase margin
The process ends when the both bandwidth and the phase
margin are sufficiently high. For this example input voltage
can vary from 3.0 to 3.6V and output current can vary from 0
to 4A, and after a few iterations a moderate gain factor of
101dB is used.
The error amplifier of the LM2743 has a unity-gain bandwidth
of 9 MHz. In order to model the effect of this limitation, the
open-loop gain can be calculated as:
The new error amplifier transfer function that takes into ac-
count unity-gain bandwidth is:
The gain and phase of the error amplifier are shown in Figure
15.
20095274
20095275
FIGURE 15. Error Amp. Gain and Phase
In VM regulators, the top feedback resistor RFB2 forms a part
of the compensation. Setting RFB2 to 10 kΩ, ±1% usually gives
values for the other compensation resistors and capacitors
that fall within a reasonable range. (Capacitances > 1pF, re-
sistances < 1MΩ) CC1, CC2, CC3, RC1, and RC2 are selected
to provide the poles and zeroes at the desired frequencies,
using the following equations:
www.national.com 18
LM2743
In practice, a good trade off between phase margin and band-
width can be obtained by selecting the closest ±10% capac-
itor values above what are suggested for CC1 and CC2, the
closest ±10% capacitor value below the suggestion for CC3,
and the closest ±1% resistor values below the suggestions
for RC1, RC2. Note that if the suggested value for RC2 is less
than 100Ω, it should be replaced by a short circuit. Following
this guideline, the compensation components will be:
CC1 = 27pF ±10%
CC2 = 820pF ±10%
CC3 = 2.7nF ±10%
RC1 = 39.2kΩ ±1%
RC2 = 2.55kΩ ±1%
The transfer function of the compensation block can be de-
rived by considering the compensation components as
impedance blocks ZF and ZI around an inverting op-amp:
As with the generic equation, GEA-ACTUAL must be modified to
take into account the limited bandwidth of the error amplifier.
The result is:
The total control loop transfer function H is equal to the power
stage transfer function multiplied by the error amplifier trans-
fer function.
H = GPS x HEA
The bandwidth and phase margin can be read graphically
from Bode plots of HEA are shown in Figure 16.
20095285
20095286
FIGURE 16. Overall Loop Gain and Phase
The bandwidth of this example circuit is 59 kHz, with a phase
margin of 60°.
EFFICIENCY CALCULATIONS
The following is a sample calculation.
A reasonable estimation of the efficiency of a switching buck
controller can be obtained by adding together the Output
Power (POUT) loss and the Total Power (PTOTAL) loss:
The Output Power (POUT) for theTypical Application Circuit
design is (1.2V x 4A) = 4.8W. The Total Power (PTOTAL), with
an efficiency calculation to complement the design, is shown
below.
The majority of the power losses are due to low and high side
of MOSFET’s losses. The losses in any MOSFET are group
of switching (PSW) and conduction losses(PCND).
PFET = PSW + PCND = 61.38 mW + 270.42 mW
PFET = 331.8 mW
FET Switching Loss (PSW)
PSW = PSW(ON) + PSW(OFF)
19 www.national.com
LM2743
PSW = 0.5 x VIN x IOUT x (tr + tf) x fSW
PSW = 0.5 x 3.3V x 4A x 300 kHz x 31 ns
PSW = 61.38 mW
The FDS6898A has a typical turn-on rise time tr and turn-off
fall time tf of 15 ns and 16 ns, respectively. The switching
losses for this type of dual N-Channel MOSFETs are 0.061W.
FET Conduction Loss (PCND)
PCND = PCND1 + PCND2
PCND1 = (IOUT)2 x RDS(ON) x k x D
PCND2 = (IOUT)2 x RDS(ON) x k x (1-D)
RDS(ON) = 13 mΩ and the factor is a constant value (k = 1.3)
to account for the increasing RDS(ON) of a FET due to heating.
PCND1 = (4A)2 x 13 mΩ x 1.3 x 0.364
PCND2 = (4A)2 x 13 mΩ x 1.3 x (1 - 0.364)
PCND = 98.42 mW + 172 mW = 270.42 mW
There are few additional losses that are taken into account:
IC Operating Loss (PIC)
PIC = IQ_VCC x VCC,
where IQ-VCC is the typical operating VCC current
PIC= 1.5 mA x 3.3V = 4.95 mW
FET Gate Charging Loss (PGATE)
PGATE = n x VCC x QGS x fSW
PGATE = 2 x 3.3V x 3 nC x 300 kHz
PGATE = 5.94 mW
The value n is the total number of FETs used and QGS is the
typical gate-source charge value, which is 3 nC. For the FD-
S6898A the gate charging loss is 5.94 mW.
Input Capacitor Loss (PCAP)
where,
Here n is the number of paralleled capacitors, ESR is the
equivalent series resistance of each, and PCAP is the dissipa-
tion in each. So for example if we use only one input capacitor
of 24 mΩ.
PCAP = 88.8 mW
Output Inductor Loss (PIND)
PIND = I2OUT x DCR
where DCR is the DC resistance. Therefore, for example
PIND = (4A)2 x 11 mΩ
PIND = 176 mW
Total System Efficiency
PTOTAL = PFET + PIC + PGATE + PCAP + PIND
www.national.com 20
LM2743
Example Circuits
20095232
FIGURE 17. 3.3V to 1.8V @ 2A, fSW = 300kHz
PART PART NUMBER TYPE PACKAGE DESCRIPTION VENDOR
U1 LM2743 Synchronous
Controller
TSSOP-14 NSC
Q1 FDS6898A Dual N-MOSFET SO-8 20V, 10mΩ@ 4.5V,
16nC
Fairchild
D1 MBR0520LTI Schottky Diode SOD-123
L1 DO3316P-472 Inductor 4.7µH, 4.8Arms
18mΩ
Coilcraft
CIN1 16SP100M Aluminum
Electrolytic
10mm x 6mm 100µF, 16V,
2.89Arms
Sanyo
CO1 6SP220M Aluminum
Electrolytic
10mm x 6mm 220µF, 6.3V 3.1Arms Sanyo
CCC, CBOOT,
CIN2, CO2
VJ1206Y104KXXA Capacitor 1206 0.1µF, 10% Vishay
CC3 VJ0805Y332KXXA Capacitor 805 3300pF, 10% Vishay
CSS VJ0805A123KXAA Capacitor 805 12nF, 10% Vishay
CC2 VJ0805A821KXAA Capacitor 805 820pF 10% Vishay
CC1 VJ0805A220KXAA Capacitor 805 22pF, 10% Vishay
RFB2 CRCW08051002F Resistor 805 10.0kΩ 1% Vishay
RFB1 CRCW08054991F Resistor 805 4.99kΩ1% Vishay
RFADJ CRCW08051103F Resistor 805 110kΩ 1% Vishay
RC2 CRCW08052101F Resistor 805 2.1kΩ 1% Vishay
RCS CRCW08052101F Resistor 805 2.1 kΩ 1% Vishay
RCC CRCW080510R0F Resistor 805 10.0Ω 1% Vishay
RC1 CRCW08055492F Resistor 805 54.9kΩ 1% Vishay
RPULL-UP CRCW08051003J Resistor 805 100kΩ 5% Vishay
21 www.national.com
LM2743
20095233
FIGURE 18. 5V to 2.5V @ 2A, fSW = 300kHz
PART PART NUMBER TYPE PACKAGE DESCRIPTION VENDOR
U1 LM2743 Synchronous
Controller
TSSOP-14 NSC
Q1 FDS6898A Dual N-MOSFET SO-8 20V, 10mΩ@ 4.5V, 16nC Fairchild
D1 MBR0520LTI Schottky Diode SOD-123
L1 DO3316P-682 Inductor 6.8µH, 4.4Arms, 27mΩCoilcraft
CIN1 16SP100M Aluminum
Electrolytic
10mm x 6mm 100µF, 16V, 2.89Arms Sanyo
CO1 10SP56M Aluminum
Electrolytic
6.3mm x 6mm 56µF, 10V 1.7Arms Sanyo
CCC, CBOOT,
CIN2, CO2
VJ1206Y104KXXA Capacitor 1206 0.1µF, 10% Vishay
CC3 VJ0805Y182KXXA Capacitor 805 1800pF, 10% Vishay
CSS VJ0805A123KXAA Capacitor 805 12nF, 10% Vishay
CC2 VJ0805A821KXAA Capacitor 805 820pF 10% Vishay
CC1 VJ0805A330KXAA Capacitor 805 33pF, 10% Vishay
RFB2 CRCW08051002F Resistor 805 10.0kΩ 1% Vishay
RFB1 CRCW08053161F Resistor 805 3.16kΩ 1% Vishay
RFADJ CRCW08051103F Resistor 805 110kΩ 1% Vishay
RC2 CRCW08051301F Resistor 805 1.3kΩ 1% Vishay
RCS CRCW08052101F Resistor 805 2.1 kΩ 1% Vishay
RCC CRCW080510R0F Resistor 805 10.0Ω 1% Vishay
RC1 CRCW08053322F Resistor 805 33.2kΩ 1% Vishay
RPULL-UP CRCW08051003J Resistor 805 100kΩ 5% Vishay
www.national.com 22
LM2743
20095234
FIGURE 19. 12V to 3.3V @ 4A, fSW = 300kHz
PART PART NUMBER TYPE PACKAGE DESCRIPTION VENDOR
U1 LM2743 Synchronous
Controller
TSSOP-14 NSC
Q1 FDS6898A Dual N-MOSFET SO-8 20V, 10mΩ@ 4.5V,
16nC
Fairchild
D1 MBR0520LTI Schottky Diode SOD-123
L1 DO3316P-332 Inductor 3.3µH, 5.4Arms 15mΩCoilcraft
CIN1 16SP100M Aluminum
Electrolytic
10mm x 6mm 100µF, 16V, 2.89Arms Sanyo
CO1 6SP220M Aluminum
Electrolytic
10mm x 6mm 220µF, 6.3V 3.1Arms Sanyo
CCC, CBOOT,
CIN2, CO2
VJ1206Y104KXXA Capacitor 1206 0.1µF, 10% Vishay
CC3 VJ0805Y222KXXA Capacitor 805 2200pF, 10% Vishay
CSS VJ0805A123KXAA Capacitor 805 12nF, 10% Vishay
CC2 VJ0805Y332KXXA Capacitor 805 3300pF 10% Vishay
CC1 VJ0805A820KXAA Capacitor 805 82pF, 10% Vishay
RFB2 CRCW08051002F Resistor 805 10.0kΩ 1% Vishay
RFB1 CRCW08052211F Resistor 805 2.21kΩ 1% Vishay
RFADJ CRCW08051103F Resistor 805 110kΩ 1% Vishay
RC2 CRCW08052611F Resistor 805 2.61kΩ 1% Vishay
RCS CRCW08054121F Resistor 805 4.12 kΩ 1% Vishay
RCC CRCW080510R0F Resistor 805 10.0Ω 1% Vishay
RC1 CRCW08051272F Resistor 805 12.7kΩ 1% Vishay
RPULL-UP CRCW08051003J Resistor 805 100kΩ 5% Vishay
23 www.national.com
LM2743
Physical Dimensions inches (millimeters) unless otherwise noted
TSSOP-14 Pin Package
NS Package Number MTC14
www.national.com 24
LM2743
Notes
25 www.national.com
LM2743
Notes
LM2743 Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products Design Support
Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench
Audio www.national.com/audio App Notes www.national.com/appnotes
Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns
Data Converters www.national.com/adc Samples www.national.com/samples
Interface www.national.com/interface Eval Boards www.national.com/evalboards
LVDS www.national.com/lvds Packaging www.national.com/packaging
Power Management www.national.com/power Green Compliance www.national.com/quality/green
Switching Regulators www.national.com/switchers Distributors www.national.com/contacts
LDOs www.national.com/ldo Quality and Reliability www.national.com/quality
LED Lighting www.national.com/led Feedback/Support www.national.com/feedback
Voltage References www.national.com/vref Design Made Easy www.national.com/easy
PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions
Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero
Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic
PLL/VCO www.national.com/wireless PowerWise® Design
University
www.national.com/training
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: support@nsc.com
Tel: 1-800-272-9959
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
