SLVS296 − JUNE 2000
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
features
DRegulated 3.3-V Output Voltage From a
1.8-V to 3.6-V Input Voltage Range
DUltraLow Operating Current in Snooze
Mode, Typical 2 µA
DLess Than 5-mV(PP) Output Voltage Ripple
Achieved With Push-Pull Topology
DIntegrated Low-Battery and Power-Good
Detector
DSwitching Frequency Can Be Synchronized
to External Clock Signal
DExtends Battery Usage With up to 90%
Efficiency and 35-µA Quiescent Current
DEasy-To-Design, Low Cost, Low EMI Power
Supply Since No Inductors Are Used
DCompact Converter Solution in UltraSmall
10-Pin MSOP With Only Four External
Capacitors Required
DEvaluation Module Available
(TPS60210EVM-167)
applications
DReplaces DC/DC Converters With Inductors
in Battery-Powered Applications Like:
− Two Battery Cells to 3.3-V Conversion
− MSP430 Ultralow-Power Microcontroller
and Other Battery Powered
Microprocessor Systems
− Glucose Meters and Other Medical
Instruments
− MP3 Portable Audio Players
− Backup-Battery Boost Converters
− Cordless Phones, PDAs
·
description
The TPS6021x step-up, regulated charge pumps generate a 3.3-V ±4% output voltage from a 1.8-V to 3.6-V
input voltage. These devices are typically powered by two alkaline, NiCd, or NiMH battery cells or by one primary
lithium MnO2 (or similar) coin cell and operate down to a minimum supply voltage of 1.6 V. Continuous output
current is a minimum of 100 mA for the TPS60210 and TPS60211, and 50 mA for the TPS60212 and TPS60213,
all from a 2-V input.
Figure 1. Typical Application Circuit With
Low-Battery Warning
OUTPUT
3.3 V
INPUT
1.6 V to 3.6 V
ON/OFF
C1
1µFC2
1µF
Co
2.2 µF
Ci
2.2 µF
R1
R2
1
2
3
4
5
6
7
8
9
10
R3
Low Battery
Warning
IN
C1−
C1+
LBI
TPS60210
OUT
C2−
C2+
LBO
GND
SNOOZE
TPS60210
PEAK OUTPUT CURRENT
vs
INPUT VOLTAGE
150
100
50
01.6 2.0 2.4 2.8
200
250
350
3.2 3.6
300
VI − Input Voltage − V
I − Output Current − mA
O
Copyright 2000, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
!"# $ %&'# "$ (&)*%"# +"#'
+&%#$ %! # $('%%"#$ (' #,' #'!$ '-"$ $#&!'#$
$#"+"+ .""#/ +&%# (%'$$0 +'$ # '%'$$"*/ %*&+'
#'$#0 "** (""!'#'$
SLVS296 − JUNE 2000
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
description (continued)
Three operating modes can be programmed using the SNOOZE pin. When SNOOZE is low, the device is put
into snooze mode. In snooze mode, the device operates with a typical quiescent current of 2 µA while the output
voltage is m a intained at 3.3 V ±6%. This is lower than the self-discharge current of most batteries. Load current
in snooze mode is limited to 2 mA. When SNOOZE is high, the device is put into normal operating mode. During
normal operating mode, the device operates in the newly developed linskip mode where it switches seamlessly
from the power saving pulse-skip mode at light loads to the low-noise constant-frequency linear-regulation
mode once the output current exceeds the linskip current threshold of about 7 mA. In this mode, the device
operates from the internal oscillator. The device is synchronized to an external clock signal if SNOOZE is
clocked; thus switching harmonics can be controlled and minimized.
Only four external capacitors are needed to build a complete low-ripple dc/dc converter. The push-pull operating
mode of two single-ended charge pumps assures the low output voltage ripple as charge is continuously
transferred to the output. All the devices can start with full load current. The devices include a low-battery
detector that issues a warning if the battery voltage drops below a user-defined threshold voltage or a
power-good detector that goes active when the output voltage reaches about 90% of its nominal value. This
dc/dc converter requires no inductors; therefore, EMI of the system is reduced to a minimum, making it easier
to use in designs. It is available in the small 10-pin MSOP package (DGS).
DGS PACKAGES
1
2
3
4
5
10
9
8
7
6
LBI
GND
C1−
C1+
OUT
LBO
SNOOZE
C2−
IN
C2+
TPS60210
TPS60212
1
2
3
4
5
10
9
8
7
6
GND
GND
C1−
C1+
OUT
PG
SNOOZE
C2−
IN
C2+
TPS60211
TPS60213
AVAILABLE OPTIONS
TAPART NUMBER†MARKING
DGS
PACKAGE
OUTPUT
CURRENT
(mA)
OUTPUT
VOLTAGE
(V) DEVICE FEATURES
TPS60210DGS AFD 100 3.3 Low-battery detector
−40°C to 85°C
TPS60211DGS AFE 100 3.3 Power-good detector
−40
°
C to 85
°
C
TPS60212DGS AFF 50 3.3 Low-battery detector
TPS60213DGS AFG 50 3.3 Power-good detector
†The DGS package is available taped and reeled. Add R suffix to device type (e.g., TPS60210DGSR) to order
quantities of 3000 devices per reel.
SLVS296 − JUNE 2000
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
functional block diagrams
TPS60210 and TPS60212 with low-battery detector
_
+
Oscillator
Control
Circuit
_
+
+
−
VREF
_
+
+
−
Shutdown/
Start-Up
Control
0.8 x VIN +
−
VREF
LBI
GND LBO
SNOOZE
Charge Pump 1
C1+
C1−
C1
C2+
C2−
OUT
C2
IN
Charge Pump 2
0°
180°
TPS60211 and TPS60213 with power-good detector
_
+
Oscillator
Control
Circuit
_
+
+
−
VREF
_
+
+
−
Shutdown/
Start-Up
Control
0.8 x VIN +
−
VREF
GND PG
SNOOZE
Charge Pump 1
C1+
C1−
C1
C2+
C2−
OUT
C2
IN
Charge Pump 2
0°
180°
SLVS296 − JUNE 2000
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME NO.
I/O
DESCRIPTION
C1+ 4 Positive terminal of the flying capacitor C1
C1− 3 Negative terminal of the flying capacitor C1
C2+ 6 Positive terminal of the flying capacitor C2
C2− 8 Negative terminal of the flying capacitor C2
GND 2 Ground
IN 7 I Supply input. Bypass IN to GND with a capacitor of a minimum of 2.2 µF.
LBI/GND 1 I Low-battery detector input for TPS60210 and TPS60212. A low-battery warning is generated at the LBO pin when
the voltage on LBI drops below the threshold of 1.18 V. Connect LBI to GND or VBAT if the low-battery detector
function is not used. For the devices TPS60211 and TPS60213, this pin is a ground (GND pin).
LBO/PG 10 O
Open-drain low-battery detector output for TPS60210 and TPS60212. This pin is pulled low if the voltage on LBI
drops below the threshold of 1.18 V. A pullup resistor should be connected between LBO and OUT or any other
logic supply rail that is lower than 3.6 V.
Open-drain power-good detector output for TPS60211 and TPS60213. As soon as the voltage on OUT reaches
about 90% of its nominal value, this pin goes active high. A pullup resistor should be connected between PG and
OUT or any other logic supply rail that is lower than 3.6 V.
OUT 5 O Regulated 3.3-V power output. Bypass OUT to GND with the output filter capacitor Co.
SNOOZE 9 I
Three operating modes can be programmed with the SNOOZE pin.
− SNOOZE = Low programs the device in the snooze mode, enabling ultralow operating current while still
maintaining the output voltage to within 3.3 V ±6%.
− SNOOZE = High programs the device into normal operation mode where it runs from the internal oscillator.
− If an external clock signal is applied to the SNOOZE pin, the charge pump operates synchronized to the
frequency of the external clock signal.
detailed description
operating principle
The TPS6021x charge pumps provide a regulated 3.3-V output from a 1.8-V to 3.6-V input. They deliver a
minimum 10 0 - m A l o a d current while maintaining the output at 3.3 V ±4%. Designed specifically for space critical
battery-powered applications, the complete converter requires only four external capacitors. The device is using
the push-pull topology to achieve the lowest output voltage ripple. The converter is also optimized for a very
small board space. It makes use of small-sized capacitors, with the highest output current rating per output
capacitance.
The TPS6021x circuits consist of an oscillator , a voltage reference, an internal resistive feedback circuit, an error
amplifier, two charge-pump power stages with high-current MOSFET switches, a shutdown/start-up circuit, and
a control circuit (see functional block diagrams).
push-pull operating mode
The two single-ended charge-pump power stages operate in the push-pull operating mode (i.e., they operate
with a 180°C phase shift). Each single-ended charge pump transfers a charge into its flying capacitor (C1 or
C2) in one-half of the period. During the other half of the period (transfer phase), the flying capacitor is placed
in series with the input to transfer its charge to the load and output capacitor (Co). While one single-ended charge
pump is in the charge phase, the other one is in the transfer phase. This operation ensures that there is a
continuous flow of charge to the load, hence the output capacitor no longer needs to buf fer the load current for
half of the switching cycle, avoiding the high, inherent output voltage ripple of conventional charge pumps.
In order to provide a regulated output voltage of 3.3 V, the TPS6021x devices operate either in
constant-frequency linear-regulation control mode or in pulse-skip mode. The mode is automatically selected
based on the output current. If the load current is low, the controller switches into the power-saving pulse-skip
mode to boost efficiency at low output power.
SLVS296 − JUNE 2000
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
detailed description (continued)
constant-frequency mode
When the output current is higher than the linskip current threshold, the charge pump runs continuously at the
switching frequency fOSC. The control circuit, fed from the error amplifier, controls the charge on C1 and C2 by
regulating the rDS(on) of the integrated MOSFET switches. When the output voltage decreases, the rDS(on)
decreases as well, resulting in a larger voltage across the flying capacitors C1 and C2. This regulation scheme
minimizes output ripple.
Since the device switches continuously, the output ripple contains well-defined frequency components, and the
circuit requires smaller external capacitors for a given output ripple. However, constant-frequency mode, due
to higher operating current, is less efficient at light loads. For this reason, the device switches seamlessly into
the pulse-skip mode when the output current drops below the linskip current threshold.
pulse-skip mode
The device enters the pulse-skip mode when the load current drops below the linskip current threshold of about
7 mA. In pulse-skip mode, the controller disables switching of the power stages when it detects an output voltage
higher than 3.3 V. It skips switching cycles until the output voltage drops below 3.3 V. Then the controller
reactivates the oscillator and switching of the power stages starts again. A 30-mV output voltage offset is
introduced in this mode.
The pulse-skip regulation mode minimizes operating current because it does not switch continuously and
deactivates all functions except the voltage reference and error amplifier when the output is higher than 3.3 V.
Even i n pulse-skip mode the rDS(ON) of the MOSFETs is controlled. This way the energy per switching cycle that
is transferred by the charge pump from the input to the output is limited to the minimum that is necessary to
sustain a regulated output voltage, with the benefit that the output ripple is kept to a minimum. When switching
is disabled in pulse-skip mode, the load is isolated from the input.
start up, snooze mode, short circuit protection
During start-up (i.e., when voltage is applied to the supply pin IN) the input is connected to the output until the
output voltage reaches 0.8 x VI. When the start-up comparator detects this limit, the actual charge pump output
stages are activated to boost the voltage higher than the input voltage. This precharging of the output current
with a limited current ensures a short start-up time and avoids high inrush currents into an empty output
capacitor.
Driving SNOOZE low, programs the device into the snooze mode. In this mode, the converter will still maintain
the output voltage at 3.3 V ±6%. The operating current in snooze mode, is however, drastically reduced to a
typical value of 2 µA, while the output current is limited to a maximum of 2 mA. If the load current increases above
2 mA, the controller recognizes a further drop of the output voltage and the device enters the start-up mode to
bring the voltage up to its nominal value again. However, it does not switch into the normal operating mode. The
device limits short circuit currents to typically 60 mA.
synchronization to an external clock signal
The operating frequency of the charge pump is limited to 400 kHz in order to avoid troublesome interference
problems in the sensitive 455-kHz IF band. The device can either run from the integrated oscillator, or an
external clock signal can be used to drive the charge pump. The maximum frequency of the external clock signal
is 800 kHz. The switching frequency used internally to drive the charge pump power stages is half of the external
clock frequency. The external clock signal is applied to the SNOOZE-pin. The device will switch into the snooze
mode if the signal on SNOOZE is held low for more than 10 µs.
When the load current drops below the linskip current threshold, the device enters the pulse-skip mode but stays
synchronized to the external clock signal.
SLVS296 − JUNE 2000
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
detailed description (continued)
low-battery detector (TPS60210 and TPS60212)
The low-battery comparator trips at 1.18 V ±5% when the voltage on pin LBI ramps down. The voltage V(TRIP)
at which the low-battery warning is issued can be adjusted with a resistive divider as shown in Figure 2. The
sum of resistors R1 and R2 is recommended to be in the 100-kΩ to 1-MΩ range.
LBO is an open drain output. An external pullup resistor to OUT, or any other voltage rail in the appropriate range,
in the 100-kΩ to 1-MΩ range is recommended. During start-up, the LBO output signal is invalid for the first
500 µs. LBO is high impedance when the device is programmed into snooze mode.
If the low battery function is not used, connect LBI to ground and leave LBO unconnected. When the device is
programmed into snooze mode (SNOOZE = LOW), the low-battery detector is disabled.
V(TRIP) +1.18 V ǒ1)R1
R2Ǔ
_
+
+
−
VREF
VBAT
IN
R1
LBI
R2
LBO
R3
V
O
Figure 2. Programming of the Low-Battery Comparator Trip Voltage
A 100-nF ceramic capacitor should be connected in parallel to R2 if large line transients are expected. These
voltage drops may inadvertently trigger the low-battery comparator and produce a wrong low-battery warning
signal at the LBO pin.
Formulas to calculate the resistive divider for low-battery detection, with VLBI = 1.13 V to 1.23 V and the sum
of resistors R1 and R2 equal 1 MΩ:
R2 +1MW VLBI
VBat
R1 +1MW*R2
(1)
(2)
Formulas to calculate the minimum and maximum battery voltage:
VBat(min) +VLBI(min)
R1
(min) )
R2
(max)
R2(max)
V
Bat(max) +VLBI(max) R1(max) )R2(min)
R2
(min)
(3
)
(4
)
SLVS296 − JUNE 2000
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
detailed description (continued)
Table 1. Recommended Values for the Resistive Divider From the E96 Series (±1%)
VIN/V R1/kΩR2/kΩVTRIP(MIN)/V VTRIP(MAX)/V
1.6 267 750 1.524 1.677
1.7 301 681 1.620 1.785
1.8 340 649 1.710 1.887
1.9 374 619 1.799 1.988
2.0 402 576 1.903 2.106
power-good detector (TPS60211 and TPS60213)
The power-good output is an open-drain output that pulls low when the output is out of regulation. When the
output rises above 91% of its nominal voltage, the power-good output is released. When the device is
programmed into snooze mode (SNOOZE = LOW), the power-good detector is disabled and PG is high
impedance. In normal operation, an external pullup resistor must be connected between PG and OUT, or any
other voltage rail in the appropriate range. The pullup resistor should be in the 100-kΩ to 1-MΩ range. If th e P G
output is not used, it should remain unconnected.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Voltage range: IN, OUT, SNOOZE, LBI, LBO, PG to GND −0.3 V to 3.6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . .
C1+, C2+ to GND −0.3 V to (VO + 0.3 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C1−, C2− to GND −0.3 V to (VI + 0.3 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output current: TPS60210, TPS60211 150 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TPS60212, TPS60213 75 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg −55°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum junction temperature, TJ150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE 1 FREE-AIR TEMPERATURE
PACKAGE TA ≤ 25°C
POWER RATING DERATING FACTOR
ABOVE TA = 25°CTA = 70°C
POWER RATING TA = 85°C
POWER RATING
DGS 424 mW 3.4 mW/_C178 mW 136 mW
The thermal resistance junction to ambient of the DGS package is RTH−JA = 294°C/W.
recommended operating conditions
MIN NOM MAX UNIT
Input voltage range, VI1.6 3.6 V
Input capacitor, Ci2.2 µF
Flying capacitors, C1, C2 1µF
Output capacitor, Co2.2 µF
Operating junction temperature, TJ−40 125 °C
SLVS296 − JUNE 2000
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at Ci= 2.2 µF, C1 = C2 = 1 µF, Co = 2.2 µF, TA = −40°C to 85°C, VI = 2.4 V,
SNOOZE = VI (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IO(MAX)
Maximum continuous output current
TPS60210 and TPS60211, VI = 2 V 100 mA
I
O(MAX
)
Maximum continuous output current
TPS60212 and TPS60213, VI = 2 V 50 mA
1.6 V < VI < 1.8 V, 0 < IO < 0.25 × IO(MAX) 3 V
Output voltage
1.8 V < VI < 2 V, 0 < IO < 0.5 × IO(MAX) 3.17 3.3 3.43 V
VO
Output voltage
2 V < VI < 3.3 V, 0 < IO < IO(MAX) 3.17 3.3 3.43 V
V
O3.3 V < VI < 3.6 V, 0 < IO < IO(MAX) 3.17 3.3 3.47 V
Output voltage in snooze mode SNOOZE = GND, 1.8 V < VI < 3.6 V,
IO < 2 mA 3.1 3.3 3.47 V
VPP Output voltage ripple IO = IO(MAX) 5 mVPP
I(Q)
Quiescent current (no-load input current) IO = 0 mA, VI = 1.8 V to 3.6 V 35 70 µA
I
(Q) Quiescent current in snooze mode SNOOZE = GND, IO = 0 mA 2 5 µA
f(OSC) Internal switching frequency 200 300 400 kHz
f(SYNC) External clock signal frequency 400 600 800 kHz
External clock signal duty cycle 30% 70%
VIL SNOOZE input low voltage VI = 1.6 V to 3.6 V 0.3 × VIV
VIH SNOOZE input high voltage VI = 1.6 V to 3.6 V 0.7 × VIV
Ilkg SNOOZE input leakage current SNOOZE = GND or VI0.01 0.1 µA
LinSkip current threshold VI = 2 V to 3 V 7 mA
Output load regulation
VI = 2.4 V, 1 mA < IO < IO(MAX),
TC = 25°C0.015
%/mA
Output load regulation
VI = 2.4 V, 10 mA < IO < IO(MAX),
TC = 25°C0.008
%/mA
Output line regulation 2 V < VI < 3.3 V, IO = 0.5 x IO(MAX),
TA = 25°C0.28 %V
I(SC) Short circuit current VI = 2.4 V, VO = 0 V 60 mA
electrical characteristics for low-battery comparator of devices TPS60210 and TPS60212 at
TA = −40°C to 85°C, VI = 2.4 V and SNOOZE = VI (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V(LBI) LBI trip voltage VI = 1.6 V to 2.2 V, Tc = 0°C to 70°C 1.13 1.18 1.23 V
LBI trip voltage hysteresis For rising voltage at LBI 10 mV
II(LBI) LBI input current V(LBI) = 1.3 V 20 100 nA
VO(LBO) LBO output voltage low V(LBI) = 0 V, I(LBO) = 1 mA 0.4 V
Ilkg(LBO) LBO leakage current V(LBI) = 1.3 V, V(LBO) = 3.3 V 0.01 0.1 µA
NOTE: During start-up of the converter the LBO output signal is invalid for the first 500 µs.
electrical characteristics for power-good comparator of devices TPS60211 and TPS60213 at
TA = −40°C to 85°C, VI = 2.4 V and SNOOZE = VI (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V(PG) Power-good trip voltage Tc = 0°C to 70°C0.87 × VO0.91 × VO0.95 × VOV
Vhys(PG) Power-good trip voltage hysteresis VO decreasing, Tc = 0°C to 70°C 1%
VO(PG) Power-good output voltage low VO = 0 V, I(PG) = 1 mA 0.4 V
Ilkg(PG) Power-good leakage current VO = 3.3 V, V(PG) = 3.3 V 0.01 0.1 µA
NOTE: During start-up of the converter the PG output signal is invalid for the first 500 µs.
SLVS296 − JUNE 2000
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURES
Efficiency
vs Output current (TPS60210 and TPS60212) 3, 4
ηEfficiency vs Input voltage 5
IOOutput current vs Input voltage 6
VO
Output voltage
vs Output current (TPS60210 and TPS60212) 7, 8
VOOutput voltage vs Input voltage (TPS60210 and TPS60212) 9, 10
IQ
Quiescent supply current
vs Input voltage 11
IQQuiescent supply current vs Output current in snooze mode 12
VOOutput voltage vs Time (Exit from snooze mode) 13
VO
Output voltage ripple
vs Time 14, 15, 16
VOOutput voltage ripple vs Time in snooze mode 17, 18
Load transient response 19
Line transient response 20
NOTE: All typical characteristics were measured using the typical application circuit of Figure 21 (unless otherwise noted).
Figure 3
0.1 IO − Output Current − mA
TPS60210
EFFICIENCY
vs
OUTPUT CURRENT
1 10 100 1000
VI = 2.4 V
VI = 1.8 V
VI = 2.7 V
Efficiency − %
100
90
80
70
60
50
40
30
20
10
0
Figure 4
0.1
IO − Output Current − mA
TPS60212
EFFICIENCY
vs
OUTPUT CURRENT
Efficiency − %
1 10 100
VI = 1.8 V
VI = 2.4 V
VI = 2.7 V
100
90
80
70
60
50
40
30
20
10
0
SLVS296 − JUNE 2000
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 5
TPS60210
EFFICIENCY
vs
INPUT VOLTAGE
0
10
20
30
40
50
60
70
80
90
100
1.6 2.0 2.4 2.8 3.2 3.6
VI − Input Voltage − V
Efficiency − %
IO = 50 mA
Figure 6
TPS60210
PEAK OUTPUT CURRENT
vs
INPUT VOLTAGE
150
100
50
01.6 2.0 2.4 2.8
200
250
350
3.2 3.6
300
VI − Input Voltage − V
I − Output Current − mA
O
Figure 7
TPS60210
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
3.2
2.9
3.5
3.4
3.3
3.1
3.0
VO− Output Voltage − V
VI = 1.8 V
VI = 2.4 V
VI = 2.7 V
VI = 3.6 V
IO − Output Current − mA
1 10 100 1000
Figure 8
3
3.05
3.10
3.15
3.20
3.25
3.30
3.35
1 10 100
VI = 3.6 V
VI = 2.7 V
VI = 2.4 VVI = 1.8 V
− Output Voltage − V
TPS60212
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
VO
IO − Output Current − mA
SLVS296 − JUNE 2000
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 9
TPS60210
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
3.0
2.9
2.8
2.71.6 2.0 2.4 2.8
3.1
3.2
3.4
3.2 3.6
3.3
1 mA
50 mA
100 mA
VO− Output Voltage − V
VI − Input Voltage − V
Figure 10
TPS60212
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
3.15
3.10
3.05
3.001.6 2.0 2.4 2.8
3.20
3.25
3.35
3.2 3.6
3.30
1 mA
25 mA
50 mA
VO− Output Voltage − V
VI − Input Voltage − V
Figure 11
30
28
24
22
20
38
26
1.6 1.8 2.0 2.2 2.4 2.6 2.8
34
32
36
V − Input Voltage − V
QUIESCENT SUPPLY CURRENT
vs
INPUT VOLTAGE
40
3.0 3.2 3.4 3.6
I − Quiescent Current − A
µ
Q
I
IO = 0 mA
SNOOZE = VI
Figure 12
0
10
20
30
40
50
60
70
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
QUIESCENT SUPPLY CURRENT
vs
OUTPUT CURRENT IN SNOOZE MODE
IO − Output Current − mA
I − Quiescent Current − A
µ
Q
VI = 2.4 V
SNOOZE = GND
SLVS296 − JUNE 2000
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 13
0 50 100 150 200 250 300
SNOOZE
350 400 450 500
3.3
3.2
3.5
3.6
3.4
t − Time − ms
− Output Voltage − V
VO
High
Low
TPS60210
OUTPUT VOLTAGE
vs
TIME
Figure 14
t − Time − µs
TPS60210
OUTPUT VOLTAGE RIPPLE
vs
TIME
050
3.22
3.24
3.34
3.38
3.36
3.32
3.30
3.26
3.28
5454035302510 15 20
− Output Voltage − V
VO
VI = 2.4 V
IO = 1 mA
Figure 15
t − Time − µs
TPS60210
OUTPUT VOLTAGE RIPPLE
vs
TIME
010
3.22
3.24
3.34
3.38
3.36
3.32
3.30
3.26
3.28
198765234
− Output Voltage − V
VO
VI = 2.4 V
IO = 10 mA
Figure 16
t − Time − µs
TPS60210
OUTPUT VOLTAGE RIPPLE
vs
TIME
3.30
3.28
3.24
3.220123456
3.34
3.36
3.38
78910
VI = 2.4 V
IO = 100 mA
3.32
3.26
− Output Voltage − V
VO
SLVS296 − JUNE 2000
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
3.3
3.2
3.1
2.9 0 100 200 300 400 500 600
3.5
3.6
TPS60210
OUTPUT VOLTAGE RIPPLE IN SNOOZE MODE
vs
TIME
3.7
700 800 900 1000
3.4
3
t − Time − µs
− Output Voltage − V
VO
VI = 2.4 V
IO = 1 mA
CO = 10 µF (Tantalum)
SNOOZE = Low
Figure 17
3.3
3.2
3.1
2.9 0 100 200 300 400 500 600
3.5
3.6
TPS60210
OUTPUT VOLTAGE RIPPLE IN SNOOZE MODE
vs
TIME
3.7
700 800 900 1000
3.4
3
t − Time − µs
− Output Voltage − V
VO
VI = 2.4 V
IO = 1 mA
CO = 2.2 µF (Ceramic)
SNOOZE = Low
Figure 18
Figure 19
TPS60210
LOAD TRANSIENT RESPONSE
100 mA
10 mA0 50 100 150 200 250 300
− Output Voltage − V
3.26
3.28
3.30
350 400 450 500
3.24
VO
− Output Current − mA
IO
t − Time − µs
VI = 2.4 V
Figure 20
TPS60210
LINE TRANSIENT RESPONSE
3.30
3.26
2.2 V 0123456
3.32
78910
IO = 50 mA
3.28
2.8 V
− Output Voltage − V
VO
− Input Voltage − V
VI
t − Time − ms
SLVS296 − JUNE 2000
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
capacitor selection
The TPS6021x devices require only four external capacitors to achieve a very low output voltage ripple. The
capacitor values are closely linked to the required output current. Low ESR (< 0.1-Ω) capacitors should be us ed
at the input and output of the charge pump. In general, the transfer capacitors (C1 and C2) will be the smallest.
A 1-µF value is recommended if full load current performance is needed. With smaller capacitor values, the
maximum possible load current is reduced and the linskip threshold is lowered.
The input capacitor improves system efficiency by reducing the input impedance. It also stabilizes the input
current of the power source. The input capacitor should be chosen according to the power supply used, the
distance from the power source to the converter IC. CI is recommended to be about two to four times as large
as the flying capacitors C1 and C2.
The minimum required capacitance is 2.2 µF. Larger values will improve the load transient performance and
will reduce the maximum output ripple voltage. The larger the output capacitor, the better the output voltage
accuracy, and the more output current can be drawn from the converter when programmed into snooze mode.
Only ceramic capacitors are recommended for input, output and flying capacitors. Depending on the material
used to manufacture them, ceramic capacitors might lose their capacitance over temperature and voltage.
Ceramic capacitors of type X7R or X5R material will keep their capacitance over temperature and voltage,
whereas Z5U- or Y5V-type capacitors will decrease in capacitance. Table 1 lists recommended capacitor
values.
SLVS296 − JUNE 2000
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
Table 2. Recommended Capacitor Values (Ceramic X5R and X7R)
LOAD CURRENT,
ILOAD
(mA)
FLYING
CAPACITORS,
C1/C2
(µF)
INPUT
CAPACITOR,
CIN
(µF)
OUTPUT
CAPACITOR,
COUT
(µF)
OUTPUT VOLTAGE
RIPPLE IN LINEAR MODE,
VP-P
(mV)
OUTPUT VOLTAGE
RIPPLE IN SKIP MODE,
VP-P
(mV)
0−100 1 2.2 2.2 3 20
0−100 1 4.7 4.7 3 10
0−100 1 2.2 10 3 7
0−100 2.2 4.7 4.7 3 10
0−50 0.47 2.2 2.2 3 20
0−25 0.22 2.2 2.2 5 15
0−10 0.1 2.2 2.2 5 15
Table 3. Recommended Capacitor Types
MANUFACTURER PART NUMBER SIZE CAPACITANCE TYPE
Taiyo Yuden UMK212BJ104MG 0805 0.1 µF Ceramic
Taiyo Yuden
EMK212BJ224MG 0805 0.22 µF Ceramic
EMK212BJ474MG 0805 0.47 µF Ceramic
LMK212BJ105KG 0805 1 µF Ceramic
LMK212BJ225MG 0805 2.2 µF Ceramic
EMK316BJ225KL 1206 2.2 µF Ceramic
LMK316BJ475KL 1206 4.7 µF Ceramic
JMK316BJ106ML 1206 10 µF Ceramic
AVX 0805ZC105KAT2A 0805 1 µF Ceramic
AVX
1206ZC225KAT2A 1206 2.2 µF Ceramic
Table 4. Recommended Capacitor Manufacturers
MANUFACTURER CAPACITOR TYPE INTERNET SITE
Taiyo Yuden X7R/X5R ceramic http://www.t−yuden.com/
AVX X7R/X5R ceramic http://www.avxcorp.com/
SLVS296 − JUNE 2000
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
typical operating circuit TPS60210
OUTPUT
3.3 V, 100 mA
INPUT
1.8 V to 3.6 V
ON/OFF
C1
1µFC2
1µF
Co
2.2 µF
Ci
2.2 µFR1
R2
1
2
3
4
5
6
7
8
9
10 R3
Low Battery
Warning
IN
C1−
C1+
LBI
TPS60210
OUT
C2−
C2+
LBO
GND
SNOOZE
Figure 21. Typical Operating Circuit TPS60210 With Low-Battery Comparator
OUTPUT
3.3 V, 50 mA
INPUT
1.6 V to 3.6 V
ON/OFF
C1
0.47 µFC2
0.47µF
Co
2.2µF
Ci
2.2 µFR1
R2
1
2
3
4
5
6
7
8
9
10 R3
Low Battery
Warning
IN
C1−
C1+
LBI
TPS60212
OUT
C2−
C2+
LBO
GND
SNOOZE
Figure 22. Typical Operating Circuit TPS60212 With Low-Battery Comparator
The current losses through the resistive divider used to set the low-battery threshold can be avoided if an
additional MOSFET (like BSS138) is used in series to the resistors. This switch is controlled using the SNOOZE
signal. When the SNOOZE-signal is taken high, the device is programmed into normal operating mode, the
switch will turn on and the resistive divider draws current to set the LBI threshold voltage. When SNOOZE is
taken low, the device is programmed into snooze mode during which the low-battery comparator is disabled.
In addition, the resistive divider R1/R2 is disconnected from GND and therefore draws no current from the
battery. A typical schematic for this circuit is shown in Figure 22.
SLVS296 − JUNE 2000
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
typical operating circuit TPS60211
OUTPUT
3.3 V, 100 mA
INPUT
1.8 V to 3.6 V
ON/OFF
C1
1µFC2
1µF
Co
2.2µF
Ci
2.2 µF
3
4
5
6
7
8
9
10 R1
Power-Good Signal
IN
C1−
C1+
TPS60211
OUT
C2−
C2+
PG
GND
1,2
SNOOZE
Figure 23. Typical Operating Circuit TPS60211 With Power-Good Comparator
power dissipation
The power dissipated in the TPS6021x devices depends mainly on input voltage (VI) and output current (IO)
and is approximated by:
P(DISS) +IOxǒ2xV
I*VOǓfor I(Q) tt IO(5)
By observing equation 5, it can be seen that the power dissipation is worse with a higher input voltage and a
higher output current. For an input voltage of 3.6 V and an output current of 100 mA, the calculated power
dissipation ( P (DISS)) is 390 mW. This is also the point where the charge pump operates with its lowest efficiency.
With the recommended maximum junction temperature of 125°C and an assumed maximum ambient operating
temperature of 85°C, the maximum allowed thermal resistance junction to ambient of the system can be
calculated.
RQJA(max) +TJ(MAX) *TA
PDISS(max) +125°C*85°C
390 mW +102°CńW(6)
PDISS must be less than that allowed by the package rating. The thermal resistance junction to ambient of the
used 10-pin MSOP is 294°C/W for an unsoldered package. The thermal resistance junction to ambient with the
IC soldered to a printed circuit using a board layout as described in the application information section, the RΘJA
is typically 200°C/W, which is higher than the maximum value calculated previously. However, in a battery
powered application, both the VI and the ambient temperature (TA) will typically be lower than the worst case
ratings used in equation 6, and PDISS should not be a problem in most applications.
layout and board space
Careful board layout is necessary due to the high transient currents and switching frequency of the converter.
All capacitors should be placed in close proximity to the device. A PCB layout proposal for a one-layer board
is given in Figure 24.
An evaluation module for the TPS60210 is available and can be ordered under product code
TPS60210EVM−167. The EVM uses the layout shown in Figure 26. The EVM has the form factor of a 14-pin
dual in-line package and can be mounted accordingly on a socket. All components, including the pins, are
shown in Figure 24. The actual size of the EVM is 17,9 mm x 10,2 mm = 182,6 mm2.
SLVS296 − JUNE 2000
18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
layout and board space (continued)
Figure 24. Recommended Component Placement and Board Layout
17,9 mm
10,2 mm
C1
C2
C3 C4
R2
C5
R3
R4
R1
IC1
Table 5. Component Identification
IC1 TPS60210
C1, C2 Flying capacitors
C3 Input capacitor
C4 Output capacitor
C5 Stabilization capacitor for LBI
R1, R2 Resistive divider for LBI
R3 Pullup resistor for LBO
R4 Pullup resistor for EN
Capacitor C5 should be included if large line transients are expected. This capacitor suppresses toggling of the
LBO due to these line changes.
SLVS296 − JUNE 2000
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
device family products
Other charge pump dc-dc converters from Texas Instruments are:
Table 6. Product Identification
PART NUMBER LITERATURE
NUMBER DESCRIPTION
TPS60100 SLVS213 2-cell to regulated 3.3-V, 200-mA low-noise charge pump
TPS60101 SLVS214 2-cell to regulated 3.3-V, 100-mA low-noise charge pump
TPS60110 SLVS215 3-cell to regulated 5.0-V, 300-mA low-noise charge pump
TPS60111 SLVS216 3-cell to regulated 5.0-V, 150-mA low-noise charge pump
TPS60120 SLVS257 2-cell to regulated 3.3-V, 200-mA high-efficiency charge pump with low-battery comparator
TPS60121 SLVS257 2-cell to regulated 3.3-V, 200-mA high-efficiency charge pump with power-good comparator
TPS60122 SLVS257 2-cell to regulated 3.3-V, 100-mA high-efficiency charge pump with low-battery comparator
TPS60123 SLVS257 2-cell to regulated 3.3-V, 100-mA high-efficiency charge pump with power-good comparator
TPS60130 SLVS258 3-cell to regulated 5.0-V, 300-mA high-efficiency charge pump with low-battery comparator
TPS60131 SLVS258 3-cell to regulated 5.0-V, 300-mA high-efficiency charge pump with power-good comparator
TPS60132 SLVS258 3-cell to regulated 5.0-V, 150-mA high-efficiency charge pump with low-battery comparator
TPS60133 SLVS258 3-cell to regulated 5.0-V, 150-mA high-efficiency charge pump with power-good comparator
TPS60140 SLVS273 2-cell to regulated 5.0-V, 100-mA charge pump voltage tripler with low-battery comparator
TPS60141 SLVS273 2-cell to regulated 5.0-V, 100-mA charge pump voltage tripler with power-good comparator
TPS60200 SLVS274 2-cell to regulated 3.3-V, 100-mA low-ripple charge pump with low-battery comparator
TPS60201 SLVS274 2-cell to regulated 3.3-V, 100-mA low-ripple charge pump with power-good comparator
TPS60202 SLVS274 2-cell to regulated 3.3-V, 50-mA low-ripple charge pump with low-battery comparator
TPS60203 SLVS274 2-cell to regulated 3.3-V, 50-mA low-ripple charge pump with power-good comparator
PACKAGE OPTION ADDENDUM
www.ti.com 30-Jul-2011
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TPS60210DGS ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60210DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60210DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60210DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60211DGS ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60211DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60212DGS ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60212DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60212DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60212DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60213DGS ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60213DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60213DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TPS60213DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
PACKAGE OPTION ADDENDUM
www.ti.com 30-Jul-2011
Addendum-Page 2
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TPS60210DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
TPS60212DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
TPS60213DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Jul-2011
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TPS60210DGSR MSOP DGS 10 2500 340.5 338.1 20.6
TPS60212DGSR MSOP DGS 10 2500 340.5 338.1 20.6
TPS60213DGSR MSOP DGS 10 2500 340.5 338.1 20.6
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Jul-2011
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and www.ti.com/automotive
Automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions www.ti.com/lprfTI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
