MC74HC175D - Motorola / Freescale Semiconductor



SEMICONDUCTOR TECHNICAL DATA

1REV 6

 Motorola, Inc. 1995

10/95

!   " 

   

High–Performance Silicon–Gate CMOS

The MC54/74HC175 is identical in pinout to the LS175. The device inputs

are compatible with standard CMOS outputs; with pullup resistors, they are

compatible with LSTTL outputs.

This device consists of four D flip–flops with common Reset and Clock

inputs, and separate D inputs. Reset (active–low) is asynchronous and

occurs when a low level is applied to the Reset input. Information at a D input

is transferred to the corresponding Q output on the next positive going edge

of the Clock input.

•Output Drive Capability: 10 LSTTL Loads

•Outputs Directly Interface to CMOS, NMOS, and TTL

•Operating Voltage Range: 2 to 6 V

•Low Input Current: 1 µA

•High Noise Immunity Characteristic of CMOS Devices

•In Compliance with the Requirements Defined by JEDEC Standard

No. 7A

•Chip Complexity 166 FETs or 41.5 Equivalent Gates

LOGIC DIAGRAM

PIN 16 = VCC

PIN 8 = GND

CLOCK

RESET 1

DATA

INPUTS

INVERTING

AND

NONINVERTING

OUTPUTS



PIN ASSIGNMENT

FUNCTION TABLE

125

VCC

CLOCK

RESET

GND

Inputs Outputs

Reset Clock D Q Q

L X X L H

H H H L

H L L H

H L X No Change

D SUFFIX

SOIC PACKAGE

CASE 751B–05

N SUFFIX

PLASTIC PACKAGE

CASE 648–08

ORDERING INFORMATION

MC54HCXXXJ

MC74HCXXXN

MC74HCXXXD

Ceramic

Plastic

SOIC

J SUFFIX

CERAMIC PACKAGE

CASE 620–10

MC54/74HC175

MOTOROLA High–Speed CMOS Logic Data

DL129 — Rev 6

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

MAXIMUM RATINGS*

ÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎÎÎ

Value

ÎÎÎ

Unit

ÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Supply Voltage (Referenced to GND)

ÎÎÎÎÎÎ

– 0.5 to + 7.0

ÎÎÎ

Vin

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Input Voltage (Referenced to GND)

ÎÎÎÎÎÎ

– 1.5 to VCC + 1.5

ÎÎÎ

Vout

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Output Voltage (Referenced to GND)

ÎÎÎÎÎÎ

– 0.5 to VCC + 0.5

ÎÎÎ

Iin

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Input Current, per Pin

ÎÎÎÎÎÎ

± 20

ÎÎÎ

Iout

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Output Current, per Pin

ÎÎÎÎÎÎ

± 25

ÎÎÎ

ICC

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Supply Current, VCC and GND Pins

ÎÎÎÎÎÎ

± 50

ÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Power Dissipation in Still Air,Plastic or Ceramic DIP†

SOIC Package†

ÎÎÎÎÎÎ

750

500

ÎÎÎ

Tstg

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Storage Temperature

ÎÎÎÎÎÎ

– 65 to + 150

ÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Lead Temperature, 1 mm from Case for 10 Seconds

(Plastic DIP or SOIC Package)

(Ceramic DIP)

ÎÎÎÎÎÎ

260

300

ÎÎÎ

*Maximum Ratings are those values beyond which damage to the device may occur.

Functional operation should be restricted to the Recommended Operating Conditions.

†Derating — Plastic DIP: – 10 mW/

C from 65

to 125

Ceramic DIP: – 10 mW/

C from 100

to 125

SOIC Package: – 7 mW/

C from 65

to 125

For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

RECOMMENDED OPERATING CONDITIONS

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎ

Min

ÎÎÎ

Max

ÎÎÎ

Unit

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Supply Voltage (Referenced to GND)

ÎÎÎ

2.0

ÎÎÎ

6.0

ÎÎÎ

ÎÎÎÎ

Vin, Vout

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Input Voltage, Output Voltage (Referenced to GND)

ÎÎÎ

VCC

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Operating Temperature, All Package Types

ÎÎÎ

– 55

ÎÎÎ

+ 125

ÎÎÎ

ÎÎÎÎ

tr, tf

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Input Rise and Fall Time VCC = 2.0 V

(Figure 1) VCC = 4.5 V

VCC = 6.0 V

ÎÎÎ

1000

500

400

ÎÎÎ

DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎÎÎÎÎÎ

Test Conditions

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎ

Guaranteed Limit

ÎÎÎ

Unit

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎÎÎÎÎÎ

Test Conditions

ÎÎÎÎ

VCC

ÎÎÎ

– 55 to

ÎÎÎÎ

125

ÎÎÎ

Unit

ÎÎÎÎ

VIH

ÎÎÎÎÎÎÎÎÎ

Minimum High–Level Input

Voltage

ÎÎÎÎÎÎÎÎÎ

Vout = 0.1 V or VCC – 0.1 V

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

1.5

3.15

4.2

ÎÎÎÎ

1.5

3.15

4.2

ÎÎÎÎ

1.5

3.15

4 2

ÎÎÎ

ÎÎÎÎ

VIL

ÎÎÎÎÎÎÎÎÎ

Maximum Low–Level Input

Voltage

ÎÎÎÎÎÎÎÎÎ

Vout = 0.1 V or VCC – 0.1 V

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

0.3

0.9

1.2

ÎÎÎÎ

0.3

0.9

1.2

ÎÎÎÎ

0.3

0.9

1.2

ÎÎÎ

ÎÎÎÎ

VOH

ÎÎÎÎÎÎÎÎÎ

Minimum High–Level Output

Voltage

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

1.9

4.4

5.9

ÎÎÎÎ

1.9

4.4

5.9

ÎÎÎÎ

1.9

4.4

5.9

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL |Iout|

4.0 mA

|Iout|

5.2 mA

ÎÎÎÎ

4.5

6.0

ÎÎÎ

3.98

5.48

ÎÎÎÎ

3.84

5.34

ÎÎÎÎ

3.70

5.20

ÎÎÎ

ÎÎÎÎ

VOL

ÎÎÎÎÎÎÎÎÎ

Maximum Low–Level Output

Voltage

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

0.1

ÎÎÎÎ

0.1

ÎÎÎÎ

0.1

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL |Iout|

4.0 mA

|Iout|

5.2 mA

ÎÎÎÎ

4.5

6.0

ÎÎÎ

0.26

ÎÎÎÎ

0.33

ÎÎÎÎ

0.40

ÎÎÎ

ÎÎÎÎ

Iin

ÎÎÎÎÎÎÎÎÎ

Maximum Input Leakage Current

ÎÎÎÎÎÎÎÎÎ

Vin = VCC or GND

ÎÎÎÎ

6.0

ÎÎÎ

± 0.1

ÎÎÎÎ

± 1.0

ÎÎÎÎ

± 1.0

ÎÎÎ

µA

ÎÎÎÎ

ICC

ÎÎÎÎÎÎÎÎÎ

Maximum Quiescent Supply

Current (per Package)

ÎÎÎÎÎÎÎÎÎ

Vin = VCC or GND

Iout = 0 µA

ÎÎÎÎ

6.0

ÎÎÎ

ÎÎÎÎ

160

ÎÎÎ

µA

NOTE:Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

This device contains protection

circuitry to guard against damage

due to high static voltages or electric

fields. However, precautions must

be taken to avoid applications of any

voltage higher than maximum rated

voltages to this high–impedance cir-

cuit. For proper operation, Vin and

Vout should be constrained to the

range GND

(Vin or V out)

VCC.

Unused inputs must always be

tied to an appropriate logic voltage

level (e.g., either GND or VCC).

Unused outputs must be left open.

MC54/74HC175

High–Speed CMOS Logic Data

DL129 — Rev 6 3 MOTOROLA

AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎ

Guaranteed Limit

ÎÎÎ

Unit

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎ

VCC

ÎÎÎ

– 55 to

ÎÎÎÎ

125

ÎÎÎ

Unit

ÎÎÎÎ

fmax

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Clock Frequency (50% Duty Cycle)

(Figures 1 and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

6.0

ÎÎÎÎ

4.8

ÎÎÎÎ

4.0

ÎÎÎ

MHz

ÎÎÎÎ

tPLH,

tPHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Propagation Delay, Clock to Q or Q

(Figures 1 and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

150

ÎÎÎÎ

190

ÎÎÎÎ

225

ÎÎÎ

ÎÎÎÎ

tPHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Propagation Delay, Reset to Q or Q

(Figures 2 and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

125

ÎÎÎÎ

155

ÎÎÎÎ

190

ÎÎÎ

ÎÎÎÎ

tTLH,

tTHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Output Transition Time, Any Output

(Figures 1 and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

ÎÎÎÎ

110

ÎÎÎ

ÎÎÎÎ

Cin

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Input Capacitance

ÎÎÎÎ

—

ÎÎÎ

ÎÎÎÎ

ÎÎÎ

NOTES:

1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

2. Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

CPD

Power Dissipation Capacitance (Per Flip–Flop)*

Typical @ 25°C, VCC = 5.0 V

CPD Power Dissipation Capacitance (Per Flip–Flop)*

*Used to determine the no–load dynamic power consumption: PD = CPD VCC2f + ICC VCC. For load considerations, see Chapter 2 of the

Motorola High–Speed CMOS Data Book (DL129/D).

TIMING REQUIREMENTS (Input tr = tf = 6 ns)

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎ

Guaranteed Limit

ÎÎÎ

Unit

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎ

VCC

ÎÎÎ

– 55 to

ÎÎÎÎ

125

ÎÎÎ

Unit

ÎÎÎÎ

tsu

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Minimum Setup Time, Data to Clock

(Figure 3)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

100

ÎÎÎÎ

125

ÎÎÎÎ

150

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Minimum Hold Time, Clock to Data

(Figure 3)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

ÎÎÎÎ

ÎÎÎ

ÎÎÎÎ

trec

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Minimum Recovery Time, Reset Inactive to Clock

(Figure 2)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

100

ÎÎÎÎ

125

ÎÎÎÎ

150

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Minimum Pulse Width, Clock

(Figure 1)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

ÎÎÎÎ

100

ÎÎÎÎ

120

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Minimum Pulse Width, Reset

(Figure 2)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

ÎÎÎÎ

100

ÎÎÎÎ

120

ÎÎÎ

ÎÎÎÎ

tr, tf

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Input Rise and Fall Times

(Figure 1)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

1000

500

400

ÎÎÎÎ

1000

500

400

ÎÎÎÎ

1000

500

400

ÎÎÎ

NOTE:Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

MC54/74HC175

MOTOROLA High–Speed CMOS Logic Data

DL129 — Rev 6

SWITCHING WAVEFORMS

Figure 1.

Figure 2.

50%

VCC

GND

RESET

CLOCK

tPLH

tPHL

50%

DATA

CLOCK

VCC

GND

Figure 3.

GND

*Includes all probe and jig capacitance

CL*

TEST POINT

DEVICE

UNDER

TEST

OUTPUT

Figure 4.

1/fmax

CLOCK

Q or Q

tftrVCC

GND

90%

50%

10%

90%

50%

10%

tPLH tPHL

tTLH tTHL

trec

VALID

tsu

TEST CIRCUIT

MC54/74HC175

High–Speed CMOS Logic Data

DL129 — Rev 6 5 MOTOROLA

D Q

CLOCK

RESET 1

EXPANDED LOGIC DIAGRAM

D Q

MC54/74HC175

MOTOROLA High–Speed CMOS Logic Data

DL129 — Rev 6

OUTLINE DIMENSIONS

J SUFFIX

CERAMIC PACKAGE

CASE 620–10

ISSUE V

N SUFFIX

PLASTIC PACKAGE

CASE 648–08

ISSUE R

19.05

6.10

—

0.39

1.40

0.21

3.18

19.93

7.49

5.08

0.50

1.65

0.38

4.31

0.51 15

1.01

1.27 BSC

2.54 BSC

7.62 BSC

MIN MINMAX MAX

INCHES MILLIMETERS

DIM 0.750

0.240

—

0.015

0.055

0.008

0.125

0.785

0.295

0.200

0.020

0.065

0.015

0.170

0.050 BSC

0.100 BSC

0.300 BSC

0.020 15

0.040

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN

FORMED PARALLEL.

4. DIM F MAY NARROW TO 0.76 (0.030) WHERE

THE LEAD ENTERS THE CERAMIC BODY.

1 8

916

–A

–

–B

–

D 16 PL

–T

–

SEATING

PLANE

J 16 PL

0.25 (0.010) T A

MS0.25 (0.010) T B

MIN MINMAX MAX

INCHES MILLIMETERS

DIM

18.80

6.35

3.69

0.39

1.02

0.21

2.80

7.50

0.51

19.55

6.85

4.44

0.53

1.77

0.38

3.30

7.74

1.01

0.740

0.250

0.145

0.015

0.040

0.008

0.110

0.295

0.020

0.770

0.270

0.175

0.021

0.070

0.015

0.130

0.305

0.040

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN

FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

2.54 BSC

1.27 BSC

0.100 BSC

0.050 BSC

–A

–

1 8

916

HGD 16 PL

–T

–

SEATING

PLANE

KJM

T A0.25 (0.010) M M

0.25 (0.010) T B A

MS S

MIN MINMAX MAX

MILLIMETERS INCHES

DIM

9.80

3.80

1.35

0.35

0.40

0.19

0.10

5.80

0.25

10.00

4.00

1.75

0.49

1.25

0.25

6.20

0.50

0.386

0.150

0.054

0.014

0.016

0.008

0.004

0.229

0.010

0.393

0.157

0.068

0.019

0.049

0.009

0.244

0.019

1.27 BSC 0.050 BSC

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL

IN EXCESS OF THE D DIMENSION AT

MAXIMUM MATERIAL CONDITION.

916

–A

–

–B

–

D16 PL

–T

–

SEATING

PLANE

R X 45°

P 8 PL

0.25 (0.010) B

M M

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751B–05

ISSUE J

MC54/74HC175

High–Speed CMOS Logic Data

DL129 — Rev 6 7 MOTOROLA

How to reach us:

USA/EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315

MFAX: RMFAX0@email.sps.mot.com –TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,

and specifically disclaims any and all liability , including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different

applications. All operating parameters, including “T ypicals” must be validated for each customer application by customer’s technical experts. Motorola does

not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in

systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of

the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such

unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless

against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.

Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer .

MC54/74HC175/D

*MC54/74HC175/D*

◊CODELINE