Document Number: 42016 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 19-Feb-07 25
Type 225P
Vishay Sprague
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
FEATURES
Utilizes minimum area where printed wiring
board space is most important
Wound from PETP polyester film and thin gauge
foil under carefully controlled atmospheric
conditions
Protected against moisture by a conformal coating of
epoxy
Specifically designed for printed wiring board applications
Widely used in computers, instrumentation and
telecommunications equipment
100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
To + 105 °C when working voltage is reduced to 70 % of
+ 85 °C rating; to + 125 °C when working voltage is reduced
to 50 % of 85 °C rating
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 100 000 Megohm for C 0.25 Microfarads
25000 Megohm - Microfarads for C > 0.25 Microfarads
At + 85 °C: 10 000 Megohm for C 0.15 Microfarads
1500 Megohm - Microfarads for C > 0.15 Microfarads
At + 105 °C: 1500 Megohm for C 0.17 Microfarads
250 Megohm - Microfarads for C > 0.17 Microfarads
At + 125 °C: 200 Megohm for C 0.13 Microfarads
25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %
Dielectric Withstanding Voltage:
Capacitors shall withstand a DC potential of 250 % of rated
voltage applied between terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at
95 % relative humidity and + 75 °C. Remove capacitors from
humidity chamber, wipe surface dry of moisture and dry in
circulating air for 4 hours. Measure insulation resistance after
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
whichever is less. Minimum product of insulation resistance
and capacitance shall be 5000 Megohm - Microfarads after
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
RoHS
COMPLIANT
DIMENSIONS in inches [millimeters]
CASE
CODE
L
(Max.)
S
Terminal A and B Terminal D
W 0.70 [17.78] 0.562 [14.275] 0.375 [9.525]
X 0.80 [20.32] 0.613 [15.570] 0.375 [9.525]
Y 1.25 [31.75] 0.969 [24.613] 0.719 [18.263]
Terminal A
L
Max.
0.237
[6.020]
Max.
S
± 0.060 [1.524]
Lead
Length
"
Terminal B
0.237
[6.020]
Max.
L
Max.
S
± 0.030 [0.762]
Lead
Length
0.237
[6.020]
Max.
Terminal D
L
Max.
S
± 0.030 [0.762]
T Max.
H
Max.
Lead
Length
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42016
26 Revision: 19-Feb-07
Type 225P
Vishay Sprague Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See Ordering Information (Ex: 225P39391WD3).
** 60 Hz rms
CAPACITANCE CHANGE
- 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125
- 50 + 100
16
14
12
10
8
6
4
2
0
2
4
6
zH0001/EGNAHC ECNATICAPAC
%
CAPACITANCE CHANGE ENVELOPE
FOR 96 % CONFIDENCE LEVEL
TEMPERATURE DEG. CENTIGRADE
DISSIPATION FACTOR VS.TEMPERATURE
TYPICAL
- 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125
- 50 + 100
TEMPERATURE DEG. CENTIGRADE
1
.5
1.0
0.5
0
% DISSIPATION/1000 Hz
STANDARD RATINGS*
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LHT
100 VDC/70 VAC**
0.001 225P10291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0012 225P12291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0015 225P15291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0018 225P18291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0022 225P22291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0027 225P27291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0033 225P33291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0039 225P39291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0047 225P47291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0056 225P56291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0068 225P68291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.0082 225P82291W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.01 225P10391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.012 225P12391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.015 225P15391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.018 225P18391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.022 225P22391W 0.70 [17.78] 0.35 [8.89] 0.25 [6.35]
0.027 225P27391W 0.70 [17.78] 0.37 [9.40] 0.27 [6.86]
0.033 225P33391W 0.70 [17.78] 0.37 [9.40] 0.27 [6.86]
0.039 225P39391W 0.70 [17.78] 0.42 [10.67] 0.30 [7.62]
0.047 225P47391W 0.70 [17.78] 0.42 [10.67] 0.30 [7.62]
0.056 225P56391W 0.70 [17.78] 0.49 [12.45] 0.34 [8.64]
0.068 225P68391W 0.70 [17.78] 0.49 [12.45] 0.34 [8.64]
0.082 225P82391W 0.70 [17.78] 0.55 [13.97] 0.40 [10.16]
0.1 225P10491W 0.70 [17.78] 0.55 [13.97] 0.40 [10.16]
0.12 225P12491X 0.80 [20.32] 0.57 [14.48] 0.37 [9.40]
0.15 225P15491X 0.80 [20.32] 0.62 [15.75] 0.40 [10.16]
0.18 225P18491X 0.80 [20.32] 0.66 [16.76] 0.43 [10.92]
0.22 225P22491X 0.80 [20.32] 0.70 [17.78] 0.46 [11.68]
0.27 225P27491X 0.80 [20.32] 0.74 [18.80] 0.49 [12.45]
0.33 225P33491X 0.80 [20.32] 0.77 [19.56] 0.52 [13.21]
0.39 225P39491X 0.80 [20.32] 0.81 [20.57] 0.55 [13.97]
0.47 225P47491X 0.80 [20.32] 0.86 [21.84] 0.60 [15.24]
0.56 225P56491Y 1.25 [31.75] 0.88 [22.35] 0.55 [13.97]
0.68 225P68491Y 1.25 [31.75] 0.90 [22.86] 0.58 [14.73]
0.82 225P82491Y 1.25 [31.75] 0.94 [23.88] 0.65 [16.51]
1.0 225P10591Y 1.25 [31.75] 0.98 [24.89] 0.72 [18.29]
Type 225P
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead Vishay Sprague
Document Number: 42016 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 19-Feb-07 27
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
** 60 Hz rms
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LHT
200 VDC/140 VAC**
0.001 225P10292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0015 225P15292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0022 225P22292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0033 225P33292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0047 225P47292X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0068 225P68292X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.01 225P10392X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.015 225P15392X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.022 225P22392X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.033 225P33392X 0.80 [20.32] 0.61 [15.49] 0.28 [7.11]
0.047 225P47392X 0.80 [20.32] 0.61 [15.49] 0.28 [7.11]
0.068 225P68392X 0.80 [20.32] 0.64 [16.26] 0.31 [7.87]
0.1 225P10492X 0.80 [20.32] 0.71 [18.03] 0.37 [9.40]
0.1 225P10492Y 1.25 [31.75] 0.64 [16.26] 0.31 [7.87]
0.15 225P15492X 0.80 [20.32] 0.74 [18.80] 0.41 [10.41]
0.22 225P22492X 0.80 [20.32] 0.77 [19.56] 0.48 [12.19]
0.33 225P33492Y 1.25 [31.75] 0.71 [18.03] 0.41 [10.41]
0.47 225P47492Y 1.25 [31.75] 0.83 [21.08] 0.50 [12.70]
0.68 225P68492Y 1.25 [31.75] 1.14 [28.96] 0.84 [21.34]
400 VDC/200 VAC**
0.001 225P10294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0015 225P15294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0022 225P22294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0033 225P33294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0047 225P47294X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0068 225P68294X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.01 225P10394X 0.80 [20.32] 0.58 [14.73] 0.28 [7.11]
0.015 225P15394X 0.80 [20.32] 0.58 [14.73] 0.28 [7.11]
0.022 225P22394X 0.80 [20.32] 0.58 [14.73] 0.31 [7.87]
0.033 225P33394X 0.80 [20.32] 0.65 [16.51] 0.34 [8.64]
0.047 225P47394X 0.80 [20.32] 0.65 [16.51] 0.41 [10.41]
0.047 225P47394Y 1.25 [31.75] 0.64 [16.26] 0.31 [7.87]
0.068 225P68394X 0.80 [20.32] 0.80 [20.32] 0.47 [11.94]
0.1 225P10494X 0.80 [20.32] 0.84 [21.34] 0.52 [13.21]
0.1 225P10494Y 1.25 [31.75] 0.74 [18.80] 0.41 [10.41]
0.15 225P15494Y 1.25 [31.75] 0.80 [20.32] 0.47 [11.94]
0.22 225P22494Y 1.25 [31.75] 0.89 [22.61] 0.56 [14. 22]
0.33 225P33494Y 1.25 [31.75] 0.99 [25.15] 0.72 [18.29]
0.47 225P47494Y 1.25 [31.75] 1.14 [28.96] 0.84 [21.34]
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42016
28 Revision: 19-Feb-07
Type 225P
Vishay Sprague Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
* 60 Hz rms
Note: Some Part Numbers are in stock and available through the Vishay Sprague® Distribution Network. Other Part Numbers are available on
special order through Vishay Sprague® Distribution. In the construction of the components described, the full intent of the specification will be
met. Vishay however, reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit
improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Vishay Sprague®
assumes no responsibility for its use nor for any infringements of patens of other rights of third parties which may result from its use.
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LHT
600 VDC/200 VAC**
0.001 225P10296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0015 225P15296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0022 225P22296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0033 225P33296X 0.80 [20.32] 0.55 [13.97] 0.25 [6.35]
0.0047 225P47296X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.0068 225P68296X 0.80 [20.32] 0.58 [14.73] 0.25 [6.35]
0.01 225P10396X 0.80 [20.32] 0.64 [16.26] 0.31 [7.87]
0.015 225P15396X 0.80 [20.32] 0.67 [17.02] 0.34 [8.64]
0.018 225P18396X 0.80 [20.32] 0.74 [18.80] 0.37 [9.40]
0.022 225P22396X 0.80 [20.32] 0.74 [18.80] 0.37 [9.40]
0.033 225P33396X 0.80 [20.32] 0.77 [19.56] 0.44 [11.18]
0.039 225P39396X 0.80 [20.32] 0.83 [21.08] 0.50 [12.70]
0.047 225P47396X 0.80 [20.32] 0.83 [21.08] 0.50 [12.70]
0.068 225P68396Y 1.25 [31.75] 0.82 [20.83] 0.47 [11.94]
0.1 225P10496Y 1.25 [31.75] 0.91 [23.11] 0.56 [14.22]
0.22 225P22496Y 1.25 [31.75] 1.10 [27.94] 0.76 [19.30]
ORDERING INFORMATION
225P 104 9 1 W D 3 (-XXX)
TYPE CAPACITANCE TOLERANCE DC VOLTAGE
RATING
CASE CODE TERMINAL LEAD LENGTH SPECIAL
CONSTRUCTION
Capacitance is
expressed in
picofarads. The first
two digits are
significant. The third
is the number of
zeros to follow.
Values must
conform to Decade
Rating for the
tolerance specified.
0 = ± 20 %
9 = ± 10 %
5 = ± 50 %
This is
expressed in
hundred of
volts.
See Dimensional
Configurations.
A = Straight Lead
B = Hairpin Crimped
D = Hockey Crimped
1 = 0.187" ± 0.030"
[4.750 ± 0.762]
2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250” [31.750]
Minimum
A three-digit suffix
may be added by
the factory to
denote special
construction.
Document Number: 91000 www.vishay.com
Revision: 18-Jul-08 1
Disclaimer
Legal Disclaimer Notice
Vishay
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
225P10591YD3 225P10492XD3 225P47291WD3 225P22291WD3 225P15394XD3 225P33394XD3
225P10494XD3 225P10491WD3 225P10392XA3 225P10451WD3 225P22491XA3 225P22492XA3
225P68291WD3 779P1025400JB3 779P1035400JB3 225P47391WD3 225P10291WD3 225P68391WD3
225P27391WD3 225P82391WD3 225P22391WD3 779P1535400JB3 779P1525400JB3 75-327 225P22394XD3
225P33391WD3 225P39391WD3 225P47294XD3 225P15391WD3 225P56391WD3 225P47392XD3
225P22392XD3 225P10394XD3 225P10392XD3 225P68492YD3 225P47491XD3 225P82491YD3 225P10391WD3
225P47494YD3 225P47492YD3 225P15494YD3 225P15492XD3 225P15491XD3 225P56491YD3
225P18491XD3 225P33491XD3 225P12491XD3 225P33494YD3 225P22494YD3 225P22492XD3 225P68491YD3
225P27491XD3 225P33492YD3 225P22491XD3 225P10294XD3 225P47394XD3 225P15291WD3
225P56291WD3 225P33291WD3 225P39291WD3 225P10292XD3 225P10291WD3-PB 225P10391WD3-PB
225P10392XA3-PB 225P10491WD3-PB 225P10492XD3-PB 225P10494XD3-PB 225P22291WD3-PB
225P22391WD3-PB 225P22491XD3-PB 225P22494YD3-PB 225P47291WD3-PB 225P47391WD3-PB
225P47394XD3-PB 225P47491XD3-PB