SL74HC175 Quad D Flip-Flop with Common Clock and Reset High-Performance Silicon-Gate CMOS The SL74HC175 is identical in pinout to the LS/ALS175. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. This device consists of four D flip-flops with common Reset and Clock inputs, and separate D inputs. Reset (active-low) is asynchronous and occurs when a low level is applied to the Reset input. Information at a D input is transferred to the corresponding Q output on the next positive-going edge of the Clock input. * Outputs Directly Interface to CMOS, NMOS, and TTL * Operating Voltage Range: 2.0 to 6.0 V * Low Input Current: 1.0 A * High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION SL74HC175N Plastic SL74HC175D SOIC TA = -55 to 125 C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs PIN 16=VCC PIN 8 = GND Outputs Reset Clock D Q Q L X X L H H H H L H L L H H L X no change X = Don't care SLS System Logic Semiconductor SL74HC175 MAXIMUM RATINGS * Symbol Parameter Value Unit -0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V DC Input Current, per Pin 20 mA DC Output Current, per Pin 25 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ 750 500 mW -65 to +150 C 260 C VOUT IIN IOUT Tstg Storage Temperature TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/C from 65 to 125C SOIC Package: : - 7 mW/C from 65 to 125C RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter DC Supply Voltage (Referenced to GND) VIN, VOUT DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, t f Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min Max Unit 2.0 6.0 V 0 VCC V -55 +125 C 0 0 0 1000 500 400 ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. SLS System Logic Semiconductor SL74HC175 DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Guaranteed Limit Test Conditions V 25 C to -55C 85 C 125 C Unit Minimum High-Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT 20 A 2.0 4.5 6.0 1.5 3.15 4.2 1.5 3.15 4.2 1.5 3.15 4.2 V VIL Maximum Low -Level Input Voltage VOUT=0.1 V or VCC-0.1 V IOUT 20 A 2.0 4.5 6.0 0.3 0.9 1.2 0.3 0.9 1.2 0.3 0.9 1.2 V VOH Minimum High-Level Output Voltage VIN=VIH or VIL IOUT 20 A 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 4.5 6.0 3.98 5.48 3.84 5.34 3.7 5.2 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 VIN= VIL or VIH IOUT 4.0 mA IOUT 5.2 mA 4.5 6.0 0.26 0.26 0.33 0.33 0.4 0.4 Symbol Parameter VIH VIN=VIH or VIL IOUT 4.0 mA IOUT 5.2 mA VOL Maximum Low-Level Output Voltage VIN= VIL or VIH IOUT 20 A V IIN Maximum Input Leakage Current VIN=VCC or GND 6.0 0.1 1.0 1.0 A ICC Maximum Quiescent Supply Current (per Package) VIN=VCC or GND IOUT=0A 6.0 8.0 80 160 A SLS System Logic Semiconductor SL74HC175 AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input t r=t f=6.0 ns) VCC Symbol Parameter Guaranteed Limit V 25 C to -55C 85C 125C Unit fmax Maximum Clock Frequency (50% Duty Cycle) (Figures 1 and 4) 2.0 4.5 6.0 6.0 30 35 4.8 24 28 4.0 20 24 MHz tPLH, t PHL Maximum Propagation Delay, Clock to Q or Q (Figures 1 and 4) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tPHL, tPLH Maximum Propagation Delay , Reset to Q or Q (Figures 2 and 4) 2.0 4.5 6.0 125 25 21 155 31 26 190 38 32 ns tTLH, t THL Maximum Output Transition Time, Any Output (Figures 1 and 4) 2.0 4.5 6.0 75 15 13 95 19 16 110 22 19 ns - 10 10 10 pF CIN Maximum Input Capacitance CPD Power Dissipation Capacitance (Per Flip-Flop) Typical @25C,VCC=5.0 V Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC 35 pF TIMING REQUIREMENTS (CL=50pF,Input t r=t f=6.0 ns) VCC Guaranteed Limit Symbol Parameter V 25 C to -55C 85C 125C Unit tSU Minimum Setup Time, Data to Clock (Figure 3) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns th Minimum Hold Time, Clock to Data (Figure 3) 2.0 4.5 6.0 3 3 3 3 3 3 3 3 3 ns trec Minimum Recovery Time, Reset Inactive to Clock (Figure 2) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns tw Minimum Pulse Width, Clock (Figure 1) 2.0 4.5 6.0 80 16 14 100 20 17 120 24 20 ns tw Minimum Pulse Width, Reset (Figure 2) 2.0 4.5 6.0 80 16 14 100 20 17 120 24 20 ns tr, tf Maximum Input Rise and Fall Times (Figure 1) 2.0 4.5 6.0 1000 500 400 1000 500 400 1000 500 400 ns SLS System Logic Semiconductor SL74HC175 Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms Figure 4. Test Circuit EXPANDED LOGIC DIAGRAM SLS System Logic Semiconductor