SPEC NO: DSAJ8704 REV NO: V.5B DATE: FEB/16/2013 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1101026777
T-1 3/4 (5mm) SOLID STATE LAMP
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Part Number: WP7113ZGC/G Green
Features
zLow power consumption.
zPopular T-1 3/4 diameter package.
zGeneral purpose leads.
zReliable and rugged.
zLong life - solid state reliability.
zAvailable on tape and reel.
zRoHS compliant.
Description
The Green source color devices are made with InGaN Light
Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAJ8704 REV NO: V.5B DATE: FEB/16/2013 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1101026777
Selection Guide
Absolute Maximum Ratings at TA=25°C
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
Part No. Dice Lens Type
V
iewing
Angle [1]
Min. Typ. 2θ1/2
WP7113ZGC/G Green (InGaN) Water Clear 12000 19000 20°
Iv (mcd) [2]
@ 20mA
Parameter Green Units
Power dissipation 120 mW
DC Forward Current 30 mA
Peak Forward Current [1] 100 mA
Reverse Voltage 5 V
Operating/Storage Temperature -40°C To +85°C
Lead Solder Temperature [2] 260°C For 3 Seconds
Lead Solder Temperature [3] 260°C For 5 Seconds
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Green 520 nm IF=20mA
λD [1] Dominant Wavelength Green 525 nm IF=20mA
Δλ1/2 Spectral Line Half-width Green 35 nm IF=20mA
C Capacitance Green 100 pF VF=0V;f=1MHz
VF [2] Forward Voltage Green 3.2 4 V IF=20mA
IR Reverse Current Green 50 uA VR = 5V
SPEC NO: DSAJ8704 REV NO: V.5B DATE: FEB/16/2013 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1101026777
Green WP7113ZGC/G
SPEC NO: DSAJ8704 REV NO: V.5B DATE: FEB/16/2013 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1101026777
PACKING & LABEL SPECIFICATIONS WP7113ZGC/G
SPEC NO: DSAJ8704 REV NO: V.5B DATE: FEB/16/2013 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1101026777
SPEC NO: DSAJ8704 REV NO: V.5B DATE: FEB/16/2013 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1101026777
All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes