SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 D D D D D description The SN54LVC541A octal buffer/driver is designed for 2.7-V to 3.6-V VCC operation and the SN74LVC541A octal buffer/driver is designed for 1.65-V to 3.6-V VCC operation. OE1 A1 A2 A3 A4 A5 A6 A7 A8 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC OE2 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 SN54LVC541A . . . FK PACKAGE (TOP VIEW) A3 A4 A5 A6 A7 OE2 D SN54LVC541A . . . J OR W PACKAGE SN74LVC541A . . . DB, DW, OR PW PACKAGE (TOP VIEW) A2 A1 OE1 VCC D EPIC (Enhanced-Performance Implanted CMOS) Submicron Process Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25C Typical VOHV (Output VOH Undershoot) > 2 V at VCC = 3.3 V, TA = 25C Power Off Disables Outputs, Permitting Live Insertion Supports Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC) ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Latch-Up Performance Exceeds 250 mA Per JESD 17 Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), Thin Shrink Small-Outline (PW), and Ceramic Flat (W) Packages, Ceramic Chip Carriers (FK), and DIPs (J) 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 Y1 Y2 Y3 Y4 Y5 A8 GND Y8 Y7 Y6 D The 'LVC541A devices are ideal for driving bus lines or buffering memory address registers. These devices feature inputs and outputs on opposite sides of the package to facilitate printed circuit board layout. The 3-state control gate is a 2-input AND gate with active-low inputs so that if either output enable (OE1 or OE2) input is high, all eight outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment. The SN54LVC541A is characterized for operation over the full military temperature range of -55C to 125C. The SN74LVC541A is characterized for operation from -40C to 85C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC is a trademark of Texas Instruments Incorporated. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 FUNCTION TABLE INPUTS A OUTPUT Y OE1 OE2 L L L L L L H H H X X Z X H X Z logic symbol OE1 OE2 A1 A2 A3 A4 A5 A6 A7 A8 & 1 EN 19 2 18 1 3 17 4 16 5 15 6 14 7 13 8 12 9 11 This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) OE1 OE2 A1 1 19 2 18 To Seven Other Channels 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Y1 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 6.5 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 6.5 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 6.5 V Voltage range applied to any output in the high or low state, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Package thermal impedance, JA (see Note 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The value of VCC is provided in the recommended operating conditions table. 3. The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions (see Note 4) SN54LVC541A VCC Supply voltage VIH High-level input voltage Operating Data retention only VIL Low-level input voltage VI Input voltage VO Output voltage IOH IOL High level output current High-level Low level output current Low-level MAX MIN MAX 2 3.6 1.65 3.6 1.5 1.5 UNIT V 0.65 x VCC VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 1.65 V to 1.95 V SN74LVC541A MIN V 1.7 2 2 0.35 x VCC VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V 0.7 0.8 V 0.8 0 5.5 0 5.5 V High or low state 0 0 VCC 5.5 0 3 state VCC 5.5 V VCC = 1.65 V VCC = 2.3 V 0 -4 -8 VCC = 2.7 V VCC = 3 V -12 -12 -24 -24 VCC = 1.65 V VCC = 2.3 V mA 4 8 VCC = 2.7 V VCC = 3 V 12 12 24 24 mA TA Operating free-air temperature -55 125 -40 85 C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS 2.7 V to 3.6 V IOH = -4 mA IOH = -8 mA SN74LVC541A TYP MAX MIN 1.65 V to 3.6 V IOH = -100 100 A VOH SN54LVC541A TYP MAX VCC MIN VCC-0.2 VCC-0.2 1.65 V 1.2 2.3 V IOH = -12 12 mA IOH = -24 mA V 1.7 2.7 V 2.2 2.2 3V 2.4 2.4 3V 2.2 2.2 1.65 V to 3.6 V IOL = 100 A UNIT 0.2 2.7 V to 3.6 V 0.2 IOL = 4 mA IOL = 8 mA 1.65 V 0.45 2.3 V 0.7 IOL = 12 mA IOL = 24 mA 2.7 V 0.4 0.4 3V 0.55 0.55 II VI = 0 to 5.5 V 3.6 V 5 5 A Ioff VI or VO = 5.5 V IOZ VO = 0 to 5.5 V VI = VCC or GND 3.6 V VI 5.5 V VOL ICC 10 A 15 10 A 10 10 10 10 500 500 0 3.6 V IO = 0 ICC One input at VCC - 0.6 V, Other inputs at VCC or GND Ci VI = VCC or GND Co VO = VCC or GND All typical values are at VCC = 3.3 V, TA = 25C. This applies in the disabled state only. 36V 3.6 2.7 V to 3.6 V V A A 3.3 V 4 4 pF 3.3 V 5.5 5.5 pF switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 3) SN54LVC541A PARAMETER FROM (INPUT) TO (OUTPUT) VCC = 2.7 V MIN 4 VCC = 3.3 V 0.3 V MAX MIN MAX UNIT tpd A Y 5.6 1 5.1 ns ten OE Y 7.5 1 7 ns tdis OE Y 7.7 1 7 ns POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figures 1 through 3) SN74LVC541A FROM (INPUT) TO (OUTPUT) MIN MAX MIN MAX MAX MIN MAX tpd A Y 5.6 1.5 5.1 ns ten OE Y 7.5 1.5 7 ns tdis OE Y 7.7 1.5 7 ns 1 ns PARAMETER VCC = 1.8 V 0.15 V VCC = 2.5 V 0.2 V VCC = 2.7 V MIN VCC = 3.3 V 0.3 V tsk(o) UNIT This information was not available at the time of publication. Skew between any two outputs of the same package switching in the same direction operating characteristics, TA = 25C TEST CONDITIONS PARAMETER Cpd Power dissipation capacitance per buffer/driver Outputs enabled Outputs disabled f = 10 MHz VCC = 1.8 V 0.15 V VCC = 2.5 V 0.2 V VCC = 3.3 V 0.3 V TYP TYP TYP 33 2 UNIT pF This information was not available at the time of publication. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION VCC = 1.8 V 0.15 V 2 x VCC S1 1k From Output Under Test Open GND CL = 30 pF (see Note A) 1k TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCC Open LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) tPLZ VCC VCC/2 VCC/2 VOL Output Waveform 2 S1 at Open (see Note B) VOL + 0.15 V VOL tPHZ tPZH VOH VCC/2 0V Output Waveform 1 S1 at 2 x VCC (see Note B) tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOH VOH - 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2 ns, tf 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION VCC = 2.5 V 0.2 V 2 x VCC S1 500 From Output Under Test Open GND CL = 30 pF (see Note A) 500 TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VCC/2 VCC/2 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC/2 VCC/2 0V tPLH Output Control (low-level enabling) tPLZ VCC VCC/2 VCC/2 VOL Output Waveform 2 S1 at GND (see Note B) VOL + 0.15 V VOL tPHZ tPZH VOH VCC/2 0V Output Waveform 1 S1 at 2 x VCC (see Note B) tPHL VCC/2 VCC VCC/2 tPZL VCC Input VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 0V 0V tsu Output VCC VCC/2 Input VCC/2 VOH VOH - 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2 ns, tf 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 2. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN54LVC541A, SN74LVC541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SCAS298H - JANUARY 1993 - REVISED JUNE 1998 PARAMETER MEASUREMENT INFORMATION VCC = 2.7 V AND 3.3 V 0.3 V 6V S1 500 From Output Under Test Open GND CL = 50 pF (see Note A) 500 TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND tw LOAD CIRCUIT 2.7 V 2.7 V Timing Input 0V 0V VOLTAGE WAVEFORMS PULSE DURATION th 2.7 V Data Input 1.5 V 1.5 V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 1.5 V 0V tPLH tPHL VOH 1.5 V 2.7 V Output Control (low-level enabling) 1.5 V 1.5 V VOL tPLZ 3V Output Waveform 1 S1 at 6 V (see Note B) Output Waveform 2 S1 at GND (see Note B) 1.5 V 0V tPZL 2.7 V Output Input 1.5 V 1.5 V tsu Input 1.5 V 1.5 V tPZH VOL + 0.3 V VOL tPHZ 1.5 V VOH - 0.3 V VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 3. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated