
   
SLVS024E – FEBRUAR Y 1983 – REVISED NOVEMBER 1999
1
www.ti.com
DComplete PWM Power Control Circuitry
DCompletely Synchronized Operation
DInternal Undervoltage Lockout Protection
DWide Supply Voltage Range
DInternal Short-Circuit Protection
DOscillator Frequency ...500 kHz Max
DVariable Dead Time Provides Control Over
Total Range
DInternal Regulator Provides a Stable 2.5-V
Reference Supply
DAvailable in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
description
The TL1451A incorporates on a single monolithic
chip all the functions required in the construction
of two pulse-width-modulation (PWM) control
circuits. Designed primarily for power-supply
control, the TL1451A contains an on-chip 2.5-V
regulator, two error amplifiers, an adjustable
oscillator, two dead-time comparators, undervol-
tage lockout circuitry, and dual common-emitter
output transistor circuits.
The uncommitted output transistors provide
common-emitter output capability for each
controller. The internal amplifiers exhibit a common-mode voltage range from 1.04 V to 1.45 V. The dead-time
control (DTC) comparator has no offset unless externally altered and can provide 0% to 100% dead time. The
on-chip oscillator can be operated by terminating RT and CT. During low VCC conditions, the undervoltage
lockout control circuit feature locks the outputs off until the internal circuitry is operational.
The TL1451AC is characterized for operation from –20°C to 85°C. The TL1451AQ is characterized for operation
from –40°C to 125°C. The TL1451AM is characterized for operation from –55°C to 125°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
TASMALL
OUTLINE
(D)
SMALL
OUTLINE
(DB)
PLASTIC DIP
(N)
SMALL
OUTLINE
(NS)
TSSOP
(PW)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
–20°C to 85°C TL1451ACD TL1451ACDB TL1451ACN TL1451ACNS TL1451ACPW
–40°C to 125°C TL1451AQD
–55°C to 125°C TL1451AMFK TL1451AMJ
The DB and PW packages are only available left-end taped and reeled (add LE suffix, i.e., TL1451ACPWLE).
Copyright 1999, Texas Instruments Incorporated        
         
       
   
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CT
RT
ERROR 1IN+
AMPLIFIER 1 1IN–
1FEEDBACK
1DTC
1OUT
GND
REF
SCP
2IN+ ERROR
2IN– AMPLIFIER 2
2FEEDBACK
2DTC
2OUT
VCC
D, DB, N, NS, PW, OR J PACKAGE
(TOP VIEW)
1920132
17
18
16
15
14
1312119 10
5
4
6
7
8
2IN+
2IN–
NC
2FEEDBACK
2DTC
1IN+
1IN–
NC
1FEEDBACK
IDTC
RT
CT
NC
REF
SCP
GND
NC
V
2
OUT
1OUT
FK PACKAGE
(TOP VIEW)
CC
        
       
        

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
2www.ti.com
functional block diagram
+
+
Oscillator
Reference
Voltage
1/2 Vref
R
S
170 kUVLO
R
92 1
VCC RT CT
10
16
7
8
REF
GND
PWM
COMP
PWM
COMP
12 k
11
14
13
12
5
15
3
4
6
2 DTC
IN+
IN
2 FEEDBACK
1 FEEDBACK
SCP
IN+
IN
1 DTC
ERROR
AMPLIFIER 2
ERROR
AMPLIFIER 1 1 OUTPUT
2 OUTPUT
COMPONENT COUNT
Resistors 65
Capacitors 8
Transistors 105
JFETs 18

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
3
www.ti.com
absolute maximum ratings over operating free-air temperature range
Supply voltage, VCC 51 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Amplifier input voltage, VI20 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Collector output voltage, VO51 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Collector output current, IO21 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous power total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA C suffix 20°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q suffix 40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix 55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg 65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only , an d
functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE TA 25°C
POWER RATING DERATING FACTOR
ABOVE TA = 25°CTA = 70°C
POWER RATING TA = 85°C
POWER RATING TA = 125°C
POWER RATING
D1088 mW 8.7 mW/°C696 mW 566 mW 218 mW
DB 775 mW 6.2 mW/°C 496 mW 403 mW
N1000 mW 8.0 mW/°C 640 mW 520 mW
NS 500 mW 4.0 mW/°C 320 mW 260 mW
PW 838 mW 6.7 mW/°C 536 mW 436 mW 168 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J1375 mW 11.0 mW/°C880 mW 715 mW 275 mW
recommended operating conditions
MIN MAX UNIT
Supply voltage, VCC 3.6 50 V
Amplifier input voltage, VI1.05 1.45 V
Collector output voltage, VO50 V
Collector output current, IO20 mA
Current into feedback terminal 45 µA
Feedback resistor, RF100 k
Timing capacitor, CT150 15000 pF
Timing resistor, RT5.1 100 k
Oscillator frequency 1 500 kHz
C suffix 20 85
Operating free-air temperature, TAQ suffix 40 125 °C
g,
A
M suffix 55 125

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
4www.ti.com
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
f = 200 kHz (unless otherwise noted)
reference section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Output voltage (pin 16) IO = 1 mA 2.4 2.5 2.6 V
O tp t oltage change ith temperat re
TA = 20°C to 25°C0.1% ±1%
Output voltage change with temperature TA = 25°C to 85°C0.2% ±1%
Input voltage regulation VCC = 3.6 V to 40 V 2 12.5 mV
Output voltage regulation IO = 0.1 mA to 1 mA 1 7.5 mV
Short-circuit output current VO = 0 3 10 30 mA
All typical values are at TA = 25°C.
undervoltage lockout section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Upper threshold voltage (VCC) 2.72 V
Lower threshold voltage (VCC)
IO( f) 01mA T
A25°C
2.6 V
Hysteresis (VCC)IO(ref) = 0.1 mA, TA = 25°C80 120 mV
Reset threshold voltage (VCC) 1.5 1.9 V
All typical values are at TA = 25°C.
short-circuit protection control section
PARAMETER
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Input threshold voltage (SCP) TA = 25°C 0.65 0.7 0.75 V
Standby voltage (SCP) No pullup 140 185 230 mV
Latched input voltage (SCP) No pullup 60 120 mV
Input (source) current VI = 0.7 V, TA = 25°C10 15 20 µA
Comparator threshold voltage (FEEDBACK) 1.18 V
All typical values are at TA = 25°C.
oscillator section
PARAMETER
TEST CONDITIONS
TL1451C
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Frequency CT = 330 pF, RT = 10 k200 kHz
Standard deviation of frequency CT = 330 pF, RT = 10 k10%
Frequency change with voltage VCC = 3.6 V to 40 V 1%
Frequency change with tem
p
erature
TA = 20°C to 25°C0.4% ±2%
Frequency change with temperature TA = 25°C to 85°C0.2% ±2%
All typical values are at TA = 25°C.

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
5
www.ti.com
dead-time control section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Input bias current (DTC) 1µA
Latch mode (source) current (DTC) TA = 25°C80 145 µA
Latched input voltage (DTC) IO = 40 µA 2.3 V
In
p
ut threshold voltage at f 10 kHz (DTC)
Zero duty cycle 2.05 2.25
V
Input threshold voltage at f = 10 kHz (DTC) Maximum duty cycle 1.2 1.45 V
All typical values are at TA = 25°C.
error-amplifier section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Input offset voltage VO (FEEDBACK) = 1.25 V ±6 mV
Input offset current VO (FEEDBACK) = 1.25 V ±100 nA
Input bias current VO (FEEDBACK) = 1.25 V 160 500 nA
1.05
Common-mode input volta
g
e ran
g
e V
CC
= 3.6 V to 40 V
1
.
05
to V
Common mode
in ut
voltage
range
VCC
=
3
.
6
V
to
40
V
to
1.45
V
Open-loop voltage amplification RF = 200 k70 80 dB
Unity-gain bandwidth 1.5 MHz
Common-mode rejection ratio 60 80 dB
Positive output voltage swing Vref0.1 V
Negative output voltage swing 1 V
Output (sink) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V 0.5 1.6 mA
Output (source) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V 45 70 µA
All typical values are at TA = 25°C.
output section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Collector off-state current VO = 50 V 10 µA
Output saturation voltage IO = 10 mA 1.2 2 V
Short-circuit output current VO = 6 V 90 mA
All typical values are at TA = 25°C.
pwm comparator section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
In
p
ut threshold voltage at f 10 kHz (FEEDBACK)
Zero duty cycle 2.05 2.25
V
Input threshold voltage at f = 10 kHz (FEEDBACK) Maximum duty cycle 1.2 1.45 V
All typical values are at TA = 25°C.
total device
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Standby supply current Off-state 1.3 1.8 mA
Average supply current RT = 10 k1.7 2.4 mA
All typical values are at TA = 25°C.

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
6www.ti.com
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
f = 200 kHz (unless otherwise noted)
reference section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
O tp t oltage (pin 16)
I1mA
TA = 25°C 2.40 2.50 2.60
V
Output voltage (pin 16) IO = 1 mA TA = MIN and 125°C 2.35 2.46 2.65 V
Output voltage change with temperature 0.63% *±4%
TA = 25°C 2.0 12.5
Input voltage regulation VCC = 3.6 V to 40 V TA = 125°C 0.7 15 mV
In ut
voltage
regulation
VCC
3.6
V
to
40
V
TA = MIN 0.3 30
mV
TA = 25°C 1.0 7.5
Output voltage regulation IO = 0.1 mA to 1 mA TA = 125°C 0.3 14 mV
Out ut
voltage
regulation
IO
0.1
mA
to
1
mA
TA = MIN 0.3 20
mV
Short-circuit output current VO = 0 3 10 30 mA
*These parameters are not production tested.
All typical values are at TA = 25°C unless otherwise indicated.
undervoltage lockout section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
TA = 25°C 2.72
Upper threshold voltage (VCC)TA = 125°C 1.70 V
Uer
threshold
voltage
(VCC)
TA = MIN 3.15
V
TA = 25°C 2.60
Lower threshold voltage (VCC)TA = 125°C 1.65 V
Lower
threshold
voltage
(VCC)
TA = MIN 3.09
V
TA = 25°C 80 120
Hysteresis (VCC)TA = 125°C 10 50 mV
Hysteresis
(VCC)
TA = MIN 10 60
mV
TA = 25°C 1.50
Reset threshold voltage (VCC)TA = 125°C 0.95 V
g(CC)
TA = MIN 1.50
All typical values are at TA = 25°C unless otherwise indicated.

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
7
www.ti.com
short-circuit protection control section
PARAMETER
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
TA = 25°C 650 700 750
Input threshold voltage (SCP) TA = 125°C 400 478 550 mV
In ut
threshold
voltage
(SCP)
TA = MIN 800 880 950
mV
Standby voltage (SCP) 140 185 230 mV
TA = 25°C 60 120
Latched input voltage (SCP) TA = 125°C 70 120 mV
Latched
in ut
voltage
(SCP)
TA = MIN 60 120
mV
Equivalent timing resistance 170 k
Comparator threshold voltage (FEEDBACK) 1.18 V
All typical values are at TA = 25°C unless otherwise indicated.
oscillator section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
C 330 F
TA = 25°C 200
Frequency CT = 330 pF,
RT=10k
TA = 125°C 195 kHz
Frequency
R
T =
10
k
TA = MIN 193
kHz
Standard deviation of frequency CT = 330 pF, RT = 10 k2%
TA = 25°C 1%
Frequency change with voltage VCC = 3.6 V to 40 V TA = 125°C 1%
Frequency
change
with
voltage
VCC
3.6
V
to
40
V
TA = MIN 3%
Frequency change with temperature 1.37% *±10%
*These parameters are not production tested.
All typical values are at TA = 25°C unless otherwise indicated.
dead-time control section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Inp t bias c rrent (DTC)
TA = 25°C 1
A
Input bias current (DTC) TA = MIN and 125°C 3 µA
Latch mode (source) current (DTC) 80 145 µA
TA = 25°C 2.30
Latched input voltage (DTC) TA = 125°C 2.22 2.32 V
Latched
in ut
voltage
(DTC)
TA = MIN 2.28 2.40
V
In
p
ut threshold voltage at f 10 kHz (DTC)
Zero duty cycle 2.05 *2.25
V
Input threshold voltage at f = 10 kHz (DTC) Maximum duty cycle *1.20 1.45 V
*These parameters are not production tested.
All typical values are at TA = 25°C unless otherwise indicated.

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
8www.ti.com
error-amplifier section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
TA = 25°C±6
Input offset voltage VO (FEEDBACK) = 1.25 V TA = 125°C±10 mV
In ut
offset
voltage
TA = MIN ±12
mV
TA = 25°C±100
Input offset current VO (FEEDBACK) = 1.25 V TA = 125°C±100 nA
In ut
offset
current
TA = MIN ±200
nA
TA = 25°C 160 500
Input bias current VO (FEEDBACK) = 1.25 V TA = 125°C 100 500 nA
In ut
bias
current
TA = MIN 142 700
nA
1.05
Common-mode input volta
g
e ran
g
e V
CC
= 3.6 V to 40 V
1
.
05
to V
Common mode
in ut
voltage
range
VCC
=
3
.
6
V
to
40
V
to
1.45
V
TA = 25°C 70 80
Open-loop voltage amplification RF = 200 kTA = 125°C 70 80 dB
O en loo
voltage
am lification
TA = MIN 64 80
dB
Unity-gain bandwidth 1.5 MHz
Common-mode rejection ratio 60 80 dB
Positive output voltage swing 2 V
Negative output voltage swing 1 V
TA = 25°C 0.5 1.6
Output (sink) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V TA = 125°C 0.4 1.8 mA
Out ut
(sink)
current
(FEEDBACK)
TA = MIN 0.3 1.7
mA
TA = 25°C45 70
Output (source) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V TA = 125°C25 50 µA
() ( )
TA = MIN 15 70
µ
All typical values are at TA = 25°C unless otherwise indicated.
output section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Collector off-state current VO = 50 V 10 µA
TA = 25°C 1.20 2.0
Output saturation voltage TA = 125°C 1.60 2.4 V
Out ut
saturation
voltage
TA = MIN 1.36 2.2
V
Short-circuit output current VO = 6 V 90 mA
All typical values are at TA = 25°C unless otherwise indicated.
pwm comparator section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
In
p
ut threshold voltage at f 10 kHz (FEEDBACK)
Zero duty cycle 2.05 *2.25
V
Input threshold voltage at f = 10 kHz (FEEDBACK) Maximum duty cycle *1.20 1.45 V
*These parameters are not production tested.
All typical values are at TA = 25°C unless otherwise indicated.

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
9
www.ti.com
total device
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYPMAX UNIT
Standby supply current Off-state 1.3 1.8 mA
Average supply current RT = 10 k1.7 2.4 mA
All typical values are at TA = 25°C unless otherwise indicated.
PARAMETER MEASUREMENT INFORMATION
87654321
910111213141516
S1
CPE 0.47 µF
Test
Input VCC = 5 V RL
4.7 k
4.7 k
RL
OUT1
OUT2
CT
330 pF RT
10 k
Test
Input
TL1451A
Figure 1. Test Circuit
Dead Time 100%
tpe
2.0 V
1.6 V
1.4 V
1.25 V
H
L
H
L
0.6 V
0 V
H
L
3.6 V
0 V
Oscillator Triangle Waveform
Error Amplifier Output
Dead-Time Input Voltage
Short-Circuit Protection
Comparator Input Voltage
PWM Comparator Output Voltage
Output Transistor Collector
Waveform
Protection Enable
Terminal Waveform
Short-Circuit Protection
Comparator Output
Power Supply Voltage
Protection Enable Time, tpe = (0.051 x 106 x Cpe) in seconds
2.8 V TYP
Figure 2. TL1451A Timing Diagram

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
10 www.ti.com
TYPICAL CHARACTERISTICS
100 k
10 k
1 k
1 M
1 k 4 k 10 k 40 k 100 k 400 k 1 M
TRIANGLE OSCILLATOR FREQUENCY
vs
TIMING RESISTANCE
CT = 150 pF
CT = 1500 pF
CT = 15000 pF
VCC = 5 V
TA = 25°C
RT Timing Resistance
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
0
1
2
3
25 0 25 50
afosc Oscillator Frequency Variation %
1
2
OSCILLATOR FREQUENCY VARIATION
vs
FREE-AIR TEMPERATURE
3
75 100
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
VCC = 3.6 V
RT = 10 k
CT = 330 pF
fosc = 200 kHz
TA Free-Air Temperature °C
osc
f
fosc Triangle Oscillator Frequency Hz
osc
f
Figure 3 Figure 4
2.2
2
1.6
1.4
0.8
2.6
1.8
Triangle Waveform Swing Voltage V
2.4
TRIANGLE WAVEFORM SWING VOLTAGE
vs
TIMING CAPACITANCE
1.2
1
VCC = 5 V
RT = 5.1 k
TA = 25°C
CT Timing Capacitance pF
101102103104105
Triangle Waveform Period uS
TRIANGLE WAVEFORM PERIOD
vs
TIMING CAPACITANCE
VCC = 5 V
RT = 5.1 k
TA = 25°C
sµ
102
101
100
101
101102103104105
CT Timing Capacitance pF
Figure 5 Figure 6

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
11
www.ti.com
TYPICAL CHARACTERISTICS
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
0
10
20
30
25 0 25 50
10
20
REFERENCE OUTPUT VOLTAGE VARIATION
vs
FREE-AIR TEMPERATURE
30
75 100
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
VCC = 3.6 V
II(ref) = 1 mA
TA Free-Air Temperature °C
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
0
10
20
30
25 0 25 50
10
20
REFERENCE OUTPUT VOLTAGE VARIATION
vs
FREE-AIR TEMPERATURE
30
75 100
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
VCC = 40 V
II(ref) = 1 mA
TA Free-Air Temperature °C
avref Reference Output Voltage Variation mV
ÁÁ
ÁÁ
ÁÁ
ÁÁ
VO(ref)
avref Reference Output Voltage Variation mV
ÁÁ
ÁÁ
ÁÁ
ÁÁ
VO(ref)
Figure 7 Figure 8
1.5
1
0.5
00 5 10 15 20 25
2
2.5
REFERENCE OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
3
30 35 40
TA = 25°C
VCC Supply Voltage V
0.8
0.7
0.6
25 0 25 50
Dropout Voltage Variation V
0.9
1
DROPOUT VOLTAGE VARIATION
vs
FREE-TEMPERATURE
1.1
75 100
TA Free-Air Temperature °C
II(ref) = 1 mA
Vref Reference Output Voltage V
ÁÁ
ÁÁ
ÁÁ
VO(ref)
Figure 9 Figure 10

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
12 www.ti.com
TYPICAL CHARACTERISTICS
3
2
1
00123
VCE Output Collector Voltage V
4
5
UNDERVOLTAGE LOCKOUT
HYSTERESIS CHARACTERISTICS
6
45
TA = 25°CTA = 20°C
IO = 10 mA
7,10
8
RL
5 V
I = IO
VDE
TA = 85°C
VCC Supply Voltage V
ÁÁ
ÁÁ
ÁÁ
VCE
2
25 0 25 50
Undervoltage Lockout Threshold Voltage V
2.5
3
UNDERVOLTAGE LOCKOUT CHARACTERISTIC
3.5
75 100
Threshold Voltage VTH
(Left Scale)
Threshold Voltage VTL
(Left Scale)
Hysteresis Voltage
(Right Scale)
300
200
100
0
Undervoltage Lockout Hystersis Voltage mV
TA Free-Air Temperature °C
3.25
2.75
2.25 50
150
250
Figure 11 Figure 12
1.20
1.15
1.10
25 0 25
Comparator Threshold Voltage V
1.25
1.30
SHORT-CIRCUIT PROTECTION CHARACTERISTICS
50 75 100
Short-Circuit Protection
Latch Reset Supply Voltage
(Right Scale)
Short-Circuit Protection
Comparator Threshold Voltage
(Left Scale)
3
2.5
2
1.5
1
RS Latch Reset Supply Voltage V
TA Free-Air Temperature °C
Figure 13

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
13
www.ti.com
TYPICAL CHARACTERISTICS
9
6
3
00 50 100 150
tpe Protection Enable Time s
12
15
PROTECTION ENABLE TIME
vs
PROTECTION ENABLE CAPACITANCE
18
200 250
tpe
CPE Protection Enable Capacitance µF
+
Protection
Latch
SR
CPE U.V.L.O.
ERROR AMP 1
ERROR AMP 2
1.25 V
Short-circuit
Protection
Comparator 12 k
15 16
SCP Vref
170 kVref Vref
Figure 14

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
14 www.ti.com
TYPICAL CHARACTERISTICS
1.75
1.5
1
0.75
0
2.25
1.25
1 k 10 k 100 k 1 M 10 M
Error Amp Maximum Output Voltage Swing V
2
f Frequency Hz
ERROR AMP MAXIMUM OUTPUT VOLTAGE SWING
vs
FREQUENCY
0.5
0.25
VCC = 5 V
TA = 25°C
70
60
40
30
0
90
50
100 1 k 10 k 100 k 1 M 2 M
Open-Loop Voltage Amplification dB
80
f Frequency Hz
OPEN-LOOP VOLTAGE AMPLIFICATION
vs
FREQUENCY
20
10
VCC = 5 V
TA = 25°C
Figure 15 Figure 16
5
20
1 k 10 k 100 k
G Gain dB
f Frequency Hz
GAIN (AMPLIFIER IN
UNITY-GAIN CONFIGURATION)
vs
FREQUENCY
10
1 M 10 M
5
0
10
15
VCC = 5 V
TA = 25°C
Figure 17

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
15
www.ti.com
TYPICAL CHARACTERISTICS
47 pF
470 pF
4700 pF
CX:
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Rref = 150
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain dB
60
f Frequency Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
Phase Shift
CxRref
Cref
Vref
39 k
39 k
+
Test Circuit
Figure 18

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
16 www.ti.com
TYPICAL CHARACTERISTICS
47 pF
470 pF
4700 pF
CX:
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Rref = 15
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain dB
60
f Frequency Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
Phase Shift
CxRref
Cref
Vref
39 k
39 k
+
Test Circuit
Figure 19

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
17
www.ti.com
TYPICAL CHARACTERISTICS
47 pF
470 pF
4700 pF
CX:
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Rref = 15
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain dB
60
f Frequency Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
Phase Shift
CxRref
Cref
Vref
39 k
39 k
+
Test Circuit
Figure 20

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
18 www.ti.com
TYPICAL CHARACTERISTICS
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain dB
60
f Frequency Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
10°
20°
30°
40°
50°
60°
70°
80°
90°
Phase Shift
Cref
Vref
39 k
39 k
+
Test Circuit
Figure 21

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
19
www.ti.com
TYPICAL CHARACTERISTICS
60
40
20
00510
Output Sink Current mA
80
100
Collector Output Saturation Voltage V
OUTPUT SINK CURRENT
vs
COLLECTOR OUTPUT SATURATION VOLTAGE
120
15 20
110
90
70
50
30
10
TA = 20°C
TA = 25°C
VCC = 3.6 V
TA = 85°C
Figure 22
MAXIMUM OUTPUT VOLTAGE SWING
vs
FREE-AIR TEMPERATURE
VO(ref) 0.01
VO(ref) 0.02
VO(ref) 0.03
VO(ref) 0.04
VO(ref) 0.05
VO(ref) 0.06
VO(ref) 0.07
1
0.9
0.8
0.7
0.6
0.5
25 0 25 50 75 100
TA Free-Air Temperature °C
Maximum Output Voltage
Swing (Right Scale)
Maximum Output
Voltage Swing (Right Scale)
+
RL
100 k
Vvom 1
33 k
33 k
VCC = 3.6 V
RL = 100 k
VOM+1 = 1.25 V
VOM 1 = 1.15 V (Right Scale)
VOM 1 = 1.35 V (Left Scale)
Vref
TEST CIRCUIT
Maximum Output Voltage Swing VVOM
Maximum Output Voltage Swing VVOM
Figure 23

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
20 www.ti.com
TYPICAL CHARACTERISTICS
50
60
90
1000 0.5 1 1.5 2 2.5 3
Output Transistor On Duty Cycle %
30
10
Dead-Time Input Voltage V
OUTPUT TRANSISTOR ON DUTY CYCLE
vs
DEAD-TIME INPUT VOLTAGE
0
3.5 4
70
20
40
80
VCC = 3.6 V
RT = 10k
CT = 330 pF
1
0.5
001020
ICC (Standby) Standby Current mA
2
STANDBY CURRENT
vs
SUPPLY VOLTAGE
30 40
1.5
ÁÁ
ÁÁ
CC
I
VCC Supply Voltage V
TA = 25°C
1.75
1.25
0.75
0.25
Figure 24 Figure 25
1
0.5
0
25 0 25 50
ICC Supply Current mA
1.5
2
STANDBY CURRENT
vs
FREE-AIR TEMPERATURE
75 100
ÁÁ
ÁÁ
CC
I
TA Free-Air Temperature °C
Average Supply Current
VCC = 6 V, RT = 10 k,
CT = 330 pF
Stand-By Current, VCC = 40 V, No Load
Stand-By Current, VCC = 3.6 V, No Load 600
400
200
0
25 0 25 50
Maximum Continuous Power Dissipation mW
800
1000
MAXIMUM CONTINUOUS POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
1200
75 100
1100
900
700
500
300
100
16-Pin N Plastic Dip
16-Pin NS Plastic SO
Thermal Resistance
125°C/W
Thermal Resistance
250°C/W
TA Free-Air Temperature
1.75
1.25
0.75
0.25
Figure 26 Figure 27

   
SLVS024E FEBRUARY 1983 REVISED NOVEMBER 1999
21
www.ti.com
APPLICATION INFORMATION
R7
R6 C4
470
1 µF
220
C2
R4
R3
33 k
33 k
470 150
220 k
0.47 µF50 k
R1
500 pF
pF
C5 R5 500
C1
87654321
910111213141516
330 pF
L1
R2
33 k
33 k
Vref
33 k33 k470
470
L2
VCC
Step-Up
Output
Step-Down
Output
TL1451A
NOTE A: Values for R1 through R7, C1 through C4, and L1 and L2 depend upon individual application.
Figure 28. High-Speed Dual Switching Regulator
PACKAGE OPTION ADDENDUM
www.ti.com 5-May-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
5962-9958401Q2A OBSOLETE LCCC FK 20 TBD Call TI Call TI
5962-9958401QEA OBSOLETE CDIP J 16 TBD Call TI Call TI
TL1451ACD ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDBLE NRND SSOP DB 16 TBD Call TI Call TI
TL1451ACDBR ACTIVE SSOP DB 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDG4 ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDR ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDRG4 ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACN ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TL1451ACNE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TL1451ACNSR ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACNSRG4 ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPW ACTIVE TSSOP PW 16 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPWLE OBSOLETE TSSOP PW 16 TBD Call TI Call TI
TL1451ACPWR ACTIVE TSSOP PW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451AMFKB OBSOLETE LCCC FK 20 TBD Call TI Call TI
TL1451AMJB OBSOLETE CDIP J 16 TBD Call TI Call TI
PACKAGE OPTION ADDENDUM
www.ti.com 5-May-2012
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TL1451AQD ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451AQDG4 ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451AQDR ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451AQDRG4 ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451CDBR ACTIVE SSOP DB 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451CDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451CN ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TL1451CNE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TL1451CNS ACTIVE SO NS 16 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451CNSG4 ACTIVE SO NS 16 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451CNSR ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451CNSRG4 ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451INSR ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451INSRG4 ACTIVE SO NS 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
PACKAGE OPTION ADDENDUM
www.ti.com 5-May-2012
Addendum-Page 3
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TL1451A, TL1451AM :
Catalog: TL1451A
Automotive: TL1451A-Q1, TL1451A-Q1
Enhanced Product: TL1451A-EP, TL1451A-EP
Military: TL1451AM
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Enhanced Product - Supports Defense, Aerospace and Medical Applications
Military - QML certified for Military and Defense Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TL1451ACDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
TL1451ACDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451ACDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451ACNSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
TL1451ACPWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TL1451AQDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451CDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
TL1451CNSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
TL1451INSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TL1451ACDBR SSOP DB 16 2000 367.0 367.0 38.0
TL1451ACDR SOIC D 16 2500 367.0 367.0 38.0
TL1451ACDR SOIC D 16 2500 333.2 345.9 28.6
TL1451ACNSR SO NS 16 2000 367.0 367.0 38.0
TL1451ACPWR TSSOP PW 16 2000 367.0 367.0 35.0
TL1451AQDR SOIC D 16 2500 367.0 367.0 38.0
TL1451CDBR SSOP DB 16 2000 367.0 367.0 38.0
TL1451CNSR SO NS 16 2000 367.0 367.0 38.0
TL1451INSR SO NS 16 2000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated