AZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY PART NUMBER: DATE: AGM 1232E SERIES FEBRUARY 10, 2001 AGM1232E SERIES GRAPHIC MODULE 1.0 MECHANICAL SPECS 1. Item Description 2. Overall Module Size 66.1mm(W) x 27.3mm(H) x max 8.5mm(D) 3. Dot Size 0.40mm(W) x 0.45mm(H) 4. Dot Pitch 0.44mm(W) x 0.49mm(H) 5. Duty 1/32 6. Controller IC SED1520FOA/DOA 7. LC Fluid Options STN, FSTN 8. Polarizer Options Reflective, Transflective, Transmissive 9. Backlight Options EL 10. Temperature Range Options Standard (0C ~ 50C), Wide (-20C ~ 70C) 2.0 ABSOLUTE MAXIMUM RATINGS Item Symbol Min Typ Max Unit Operating temperature (Standard) Top 0 - 50 C Storage temperature (Standard) Tst -20 - 70 C Operating temperature (Wide temperature) Top -20 - 70 C Storage temperature (Wide temperature) Tst -30 - 80 C Input voltage Vin Vss Vdd V Supply voltage for logic Vdd- Vss -0.3 - 7.0 V Supply voltage for LCD drive Vdd- Vee 5.0 6.5 9.5 V AZ DISPLAYS, INC. 1 AGM1232E SERIES GRAPHIC MODULE 3.0 ELECTRICAL CHARACTERISTICS Item Symbol Condition Min Typ Max Unit Input voltage (high) Vih H level 3.5 - Vdd V Input voltage (low) Vil L level 0 - 1.5 V 0"C - 7.8 10.0 25"C - 6.5 - 50"C 4.3 5.5 - -20"C - 8.5 10.8 0"C - 7.8 - 50"C 4.3 5.5 - 70"C 3.5 4.8 - Idd Vdd=5.0V - - 13.0 mA LED Power Supply Voltage Vfled R=6.8 - 4.4 5.0 V LED Power Supply Current Ifled R=6.8 - 300 420 mA Recommended LC Driving Voltage (Standard Temp) Vdd - Vee Recommended LC Driving Voltage (Wide Temp) Vdd -Vee Power Supply Current V V 4.0 OPTICAL CHARACTERISTICS Item Mode R S Cr (Contrast Ratio) (Viewing Angle) (Viewing Angle) 25"C 25"C 25"C MIN. TYP. MIN TYP. MIN TYP. A 2.8 3.05 80 85 - 35 B 7.10 7.70 80 85 - 35 C - - - - - - A 2.49 2.99 80 85 - 35 B 7.05 7.55 80 85 - 35 C - - - - - - Note: R: Reflective S: Transflective A: STN Gray B: STN Yellow C: FSTN At: =0, =0 AZ DISPLAYS, INC. 2 AGM1232E SERIES GRAPHIC MODULE Item Symbol Condition Min Typ Max Unit Response time (rise) Tr 25 " C - 80 160 ms Response time (fall) Tf 25"C - 50 100 ns 5.0 BLOCK DIAGRAM ~ 1. AO 2.E1 6. R/W 7. Vss 16.Vdd 17.RST 18.Vo 8.DB0 15.DB7 SEG61-122 SEG1-60 61 U1 COM1-16 8 SEG1 SEG60SEG61 SEG122 COM1 COM16 COM17 Ck FR 5 COM17-32 61 LCD 122x32 COM32 U2 SEG61-122 3.E2 19 EL 20 EL AZ DISPLAYS, INC. ELBACKLIGHT 3 AGM1232E SERIES GRAPHIC MODULE 6.0 PIN ASSIGNMENT Pin No. Symbol Function 1 AO Instruction/Data H/L 2 E1 Enable for IC1 H/L 3 E2 Enable for IC2 H/L 4 NC No Connect 5 NC No Connect 6 R/W 7 Vss Ground - 8 DB0 Data bit 0 H/L 9 DB1 Data bit 1 H/L 10 DB2 Data bit 2 H/L 11 DB3 Data bit 3 H/L 12 DB4 Data bit 4 H/L 13 DB5 Data bit 5 H/L 14 DB6 Data bit 6 H/L 15 DB7 Data bit 7 H/L 16 Vdd Power Supply For Logic Circuit 17 RST Reset 18 Vee Power Supply For LCD Driving 19 EL Power Supply for EL - 20 EL Power Supply for EL - H: Data read L: Data write Level H/L 7.0 POWER SUPPLY AZ DISPLAYS, INC. 4 AGM1232E SERIES GRAPHIC MODULE 8.0 TIMING CHARACTERISTICS Symbol Test Condition Min. Typ. Max. Unit System cycle time Item tCYC6 Fig. a, Fig. b 1000 - - ns Address setup time tAW6 Fig. a, Fig. b 20 - - ns Address hold time tAH6 Fig. a, Fig. b 10 - - ns Data hold time tDH6 Fig. a 10 - - ns Data setup time tDS6 Fig. a 80 - - ns Output disable time tOH6 10 - 60 ns Access time tACC6 - - 90 Enable pulsewidth Read Write Rise and fall time CL=100 pF TEW Tr, Tf Fig. a, Fig. b 100 ns 80 ns - - 15 ns t CYC6 t EW E t AW6 R/W tr tf VIH1 VIH1 V IL1 V IL1 tH t AH6 A0,CS VIH1 VIH1 V IL1 V IL1 t t ACC6 DB0~DB7 t OH6 VIH1 VIH1 V IL1 V IL1 Valid Data Fig. a Interface timing (data Read) AZ DISPLAYS, INC. 5 AGM1232E SERIES GRAPHIC MODULE t CYC6 t EW E tr t AW6 R/W t DS6 tf V IH1 VIH1 VIL1 V IL1 t AH6 A0,CS V IH1 VIH1 VIL1 V IL1 t DH6 VIH1 DB0~DB7 VIH1 Valid Data V IL1 VIL1 Fig. b Interface timing (data Write) 9.0 RELIABILITY TEST Evaluations and Assessment* Storage Condition Operation at high temperature and humidity High temperature storage Low temperature storage Content Current Consumption Oozing Contrast Other Appearances 40 C,90% RH,240hrs Twice initial value or less none More than 80% of initial value No abnormality 60 C, 240hrs -20 C, 240hrs Twice initial value or less Twice initial value or less none More than 80% of initial value No abnormality More than 80% of initial value No abnormality *Evaluations and assessment to be made two hours after returning to room temperature (25 C5 C). *The LCDs subjected to the test must not have dew condensation. AZ DISPLAYS, INC. 6 10.0 MECHANICAL DIMENSIONS AO No Connect No Connect AZ DISPLAYS, INC. AGM1232E SERIES GRAPHIC MODULE 11.0 RELATION BETWEEN DISPLAY PATTERN AND DRIVERS AZ DISPLAYS, INC. 8 AGM1232E SERIES GRAPHIC MODULE 12.0 DISPLAY CONTROL INSTRUCTION The display control instructions control the internal state of the SED1520DOA/FOA. Instructions are received from MPU to SED1520DOA/FOA for the display control. INSTRUCTION A0 RD R/W DB7 DB6 DB5 Display ON/OFF 0 1 0 1 0 1 0 1 1 Set Page Address 0 1 0 1 0 1 1 1 0 0 1 0 0 0 1 0 1 Set Column (Segment address) Display Start Line DB4 DB3 DB2 DB1 1 DB0 1/0 Page (0~3) 0 Turns display on or off. 0: OFF. 1:ON Sets display RAM Page in Page address register Sets display RAM column address in column address register Column address (0~79) 1 DESCRIPTION Display start line (0~31) Indicates the display data RAM displayed at the top of the screen. Reads the following status: BUSY 0: Ready 1: Busy RESET 1 ON/OFF 0 ADC 0 BUSY Status Read ADC 0 0 0 0 1: CW output 0: CCW output ON/OFF 0: Display on 1: Display off RESET 0: Normal 1: Being Reset Write Display Data 1 1 0 Write Data Writes data DB0~DB7 from bus into display data RAM. Read Display Data 1 0 1 Read Data Reads data DB0~DB7 from display data RAM onto the data bus. Select ADC 0 1 0 1 0 1 0 0 0 0 0/1 Static drive ON/OFF 0 1 0 1 0 1 0 0 1 0 0/1 Select duty 0 1 0 1 0 1 0 1 0 0 0/1 Read-Modify-Wreti 0 1 0 1 1 1 0 0 0 0 0 Read-Modify-write ON END 0 1 0 1 1 1 0 1 1 1 0 Read-Modify-write OFF Reset 0 1 0 1 1 1 0 0 0 1 0 Software reset AZ DISPLAYS, INC. 0: CW output,1: CCW output 1: Static drive, 0: Normal driving Select LCD duty cycle 1:1/32, 0: 1/16 9