Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type: B41866
Date: December 2010
© EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Long-life grade capacitors for automotive electronics
Applications
High-reliability equipment in industrial and automotive
electronics
High-temperature environments
Features
High reliability and long useful life
High ripple current capability
Wide temperature range up to 125 °C
RoHS-compatible
Construction
Charge-discharge proof, polar
Aluminum case with insulating sleeve
Minus pole marking on the insulating sleeve
Case with safety vent
Delivery mode
Terminal configurations and packing:
Bulk
Taped, Ammo pack
Cut (see chapter "Single-ended Taping, packing and lead
configurations, Cut leads (Chapter B)")
Kinked (see chapter "Single-ended Taping, packing and
lead configurations, Kinked leads (Chapter B)")
PAPR (protection against polarity reversal):
crimped leads, J leads, bent leads
Refer to chapter "Single-ended capacitors Taping, packing
and lead configurations" for further details.
Single-ended capacitors B41866
High ripple current 125 °C
Page 2 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Specifications and characteristics in brief
Rated voltage VR10 ... 75 V DC
Surge voltage VS1.15 VR(1.1 VRfor 75 V DC)
Rated capacitance CR10 ... 10000 µF
Capacitance tolerance ±20% M
Dissipation factor tan δ
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR(V DC) 10 16 ... 25 35 50 63 75
tan δ(max.) 0.20 0.17 0.12 0.10 0.12 0.12
Leakage current Ileak
(20 °C, 5 min)
or 3 µA, whichever is greater
Self-inductance ESL Diameter (mm) 8 ... 12.5 16 18
ESL (nH) 20 26 34
Useful life
125 °C; VR; IAC,R > 2000 h for ∅= 8 mm and VR≤63 V
> 3000 h for ∅= 10 mm and VR≤63 V
> 3000 h for VR= 75 V
> 5000 h for ∅≥12.5 mm and VR≤63 V
Requirements ∆C/C ≤ ±35% of initial value
tan δ ≤ 3 times initial specified limit
Ileak ≤initial specified limit
Voltage endurance test
125 °C; VR2000 h for ∅= 8 mm and VR≤63 V
3000 h for ∅= 10 mm and VR≤63 V
3000 h for VR= 75 V
5000 h for ∅≥12.5 mm and VR≤63 V
Post test requirements ∆C/C ≤ ±30% of initial value
tan δ ≤ 2 times initial specified limit
Ileak ≤initial specified limit
Vibration resistance test To IEC 60068-2-6, test Fc:
Frequency range 10 Hz … 2 kHz, displacement amplitude max.
1.5 mm, acceleration max. 20 g, duration 3 ×2 h.
Capacitor rigidly clamped by the aluminum case.
IEC climatic category To IEC 60068-1:
55/125/56 (55 °C/+125 °C/56 days damp heat test)
Sectional specification IEC 60384-4, AEC-Q200
B41866
High ripple current 125 °C
Page 3 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawings
With stand-off rubber seal
Diameters (mm): 10, 12.5, 16, 18
With flat rubber seal
Diameter (mm): 8
Dimensions and weights
Dimensions (mm) Approx. weight
d +0.5 l a ±0.5 b g
8 11.5 +1.5 3.5 0.60 ±0.05 1.0
10 12.5 +1.0 5.0 0.60 ±0.05 1.6
10 16 +1.0 5.0 0.60 ±0.05 1.9
10 20 +2.0 5.0 0.60 ±0.05 2.6
12.5 20 +2.0 5.0 0.60 ±0.05 3.6
12.5 25 +2.0 5.0 0.60 ±0.05 4.5
12.5 40 +2.0 5.0 0.80 ±0.05 7.4
16 20 +2.0 7.5 0.80 ±0.05 5.5
16 25 +2.0 7.5 0.80 ±0.05 7.5
16 31.5 +2.0 7.5 0.80 ±0.05 7.8
16 35.5 +2.0 7.5 0.80 ±0.05 9.2
18 20 +2.0 7.5 0.80 ±0.1 8.0
18 25 +2.0 7.5 0.80 ±0.1 9.0
18 31.5 +2.0 7.5 0.80 ±0.1 11.0
18 35 +2.0 7.5 0.80 ±0.1 13.0
18 40 +2.0 7.5 0.80 ±0.1 16.0
B41866
High ripple current 125 °C
Page 4 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types
VR(V DC) 10 16 25 35
Case dimensions d ×l (mm)
CR(µF)
100 8 ×11.5 8 ×11.5 8 ×11.5
120 8 ×11.5 8 ×11.5 8 ×11.5
150 8 ×11.5 8 ×11.5 10 ×12.5
180 8 ×11.5 8 ×11.5 10 ×12.5
220 8 ×11.5 8 ×11.5 10 ×12.5
270 8 ×11.5 10 ×12.5 10 ×16
330 8 ×11.5 8 ×11.5 10 ×12.5 10 ×16
390 8 ×11.5 10 ×12.5 10 ×16 10 ×20
470 8 ×11.5 10 ×12.5 10 ×16 10 ×20
560 10 ×12.5 10 ×12.5 10 ×20 12.5 ×20
680 10 ×16 10 ×16 10 ×20 12.5 ×20
820 10 ×16 10 ×16 12.5 ×20 12.5 ×25
1000 10 ×16 10 ×20 12.5 ×20 16 ×20
1200 10 ×20 12.5 ×20 12.5 ×25 16 ×25
1500 10 ×20 12.5 ×25 12.5 ×25 16 ×25
18 ×20
1800 12.5 ×20 12.5 ×25 16 ×20 16 ×31.5
18 ×25
2200 12.5 ×20 16 ×20 12.5 ×40
16 ×25
18 ×20
16 ×35.5
18 ×31.5
2700 12.5 ×25 16 ×25
18 ×20
18 ×25 18 ×35
3300 16 ×20 18 ×25 16 ×31.5 18 ×40
3900 16 ×25 18 ×25 16 ×35.5
18 ×31.5
4700 16 ×25
18 ×20
18 ×31.5 18 ×35
5600 16 ×31.5 18 ×35 18 ×40
6800 18 ×31.5 18 ×40
8200 18 ×31.5
10000 18 ×40
B41866
High ripple current 125 °C
Page 5 of 39Please read Cautions and warnings and
Important notes at the end of this document.
VR(V DC) 50 63 75
Case dimensions d ×l (mm)
CR(µF)
10 8 ×11.5
12 8 ×11.5
15 8 ×11.5
18 8 ×11.5
22 8 ×11.5
27 8 ×11.5
33 8 ×11.5 8 ×11.5
39 8 ×11.5 10 ×12.5
47 8 ×11.5 10 ×12.5
56 8 ×11.5 10 ×12.5
68 8 ×11.5 10 ×16
82 8 ×11.5 10 ×16
100 10 ×12.5 10 ×16
120 10 ×16 10 ×16
150 10 ×16 10 ×16
180 10 ×20 10 ×20
220 10 ×20 12.5 ×20
270 10 ×20 12.5 ×20 16 ×20
330 12.5 ×20 12.5 ×20 16 ×25
18 ×20
390 12.5 ×25 12.5 ×25
470 12.5 ×25
16 ×20
16 ×20 16 ×31.5
18 ×25
560 16 ×20 16 ×20
680 16 ×25 12.5 ×40
16 ×25
18 ×20
18 ×31.5
820 16 ×25
18 ×20
16 ×31.5 18 ×35
1000 16 ×31.5
18 ×25
16 ×31.5 18 ×40
1200 16 ×35.5
18 ×31.5
18 ×31.5
1500 18 ×35 18 ×35
1800 18 ×40 18 ×40
Other voltage and capacitance ratings are available upon request.
B41866
High ripple current 125 °C
Page 6 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 10 V DC
330 8 ×11.5 5.170 0.646 0.573 297 B41866C3337M***
390 8 ×11.5 5.170 0.646 0.573 297 B41866C3397M***
470 8 ×11.5 5.170 0.646 0.573 297 B41866C3477M***
560 10 ×12.5 2.980 0.373 0.336 450 B41866C3567M***
680 10 ×16 1.404 0.175 0.160 714 B41866C3687M***
820 10 ×16 1.404 0.175 0.160 714 B41866C3827M***
1000 10 ×16 1.404 0.175 0.160 714 B41866C3108M***
1200 10 ×20 1.070 0.134 0.127 875 B41866C3128M***
1500 10 ×20 1.070 0.134 0.127 875 B41866C3158M***
1800 12.5 ×20 0.881 0.110 0.104 1105 B41866C3188M***
2200 12.5 ×20 0.881 0.110 0.104 1105 B41866C3228M***
2700 12.5 ×25 0.710 0.089 0.082 1358 B41866C3278M***
3300 16 ×20 0.401 0.050 0.046 1895 B41866C3338M***
3900 16 ×25 0.314 0.039 0.037 2279 B41866C3398M***
4700 16 ×25 0.314 0.039 0.037 2279 B41866C3478M***
4700 18 ×20 0.341 0.043 0.040 2190 B41866D3478M***
5600 16 ×31.5 0.249 0.031 0.029 2822 B41866C3568M***
6800 18 ×31.5 0.226 0.028 0.027 3178 B41866C3688M***
8200 18 ×31.5 0.226 0.028 0.027 3178 B41866C3828M***
10000 18 ×40 0.153 0.019 0.018 4244 B41866C3109M***
B41866
High ripple current 125 °C
Page 7 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 16 V DC
100 8 ×11.5 5.170 0.646 0.573 297 B41866C4107M***
120 8 ×11.5 5.170 0.646 0.573 297 B41866C4127M***
150 8 ×11.5 5.170 0.646 0.573 297 B41866C4157M***
180 8 ×11.5 5.170 0.646 0.573 297 B41866C4187M***
220 8 ×11.5 5.170 0.646 0.573 297 B41866C4227M***
270 8 ×11.5 5.170 0.646 0.573 297 B41866C4277M***
330 8 ×11.5 5.170 0.646 0.573 297 B41866C4337M***
390 10 ×12.5 2.980 0.373 0.336 450 B41866C4397M***
470 10 ×12.5 2.980 0.373 0.336 450 B41866C4477M***
560 10 ×12.5 2.980 0.373 0.336 450 B41866C4567M***
680 10 ×16 1.404 0.175 0.160 714 B41866C4687M***
820 10 ×16 1.404 0.175 0.160 714 B41866C4827M***
1000 10 ×20 1.070 0.134 0.127 875 B41866C4108M***
1200 12.5 ×20 0.881 0.110 0.104 1105 B41866C4128M***
1500 12.5 ×25 0.710 0.089 0.082 1358 B41866C4158M***
1800 12.5 ×25 0.710 0.089 0.082 1358 B41866C4188M***
2200 16 ×20 0.401 0.050 0.046 1895 B41866C4228M***
2700 16 ×25 0.314 0.039 0.037 2279 B41866C4278M***
2700 18 ×20 0.341 0.043 0.040 2190 B41866D4278M***
3300 18 ×25 0.314 0.039 0.037 2454 B41866C4338M***
3900 18 ×25 0.314 0.039 0.037 2454 B41866C4398M***
4700 18 ×31.5 0.226 0.028 0.027 3178 B41866C4478M***
5600 18 ×35 0.187 0.023 0.022 3638 B41866C4568M***
6800 18 ×40 0.153 0.019 0.018 4244 B41866C4688M***
B41866
High ripple current 125 °C
Page 8 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 25 V DC
100 8 ×11.5 5.170 0.646 0.573 297 B41866C5107M***
120 8 ×11.5 5.170 0.646 0.573 297 B41866C5127M***
150 8 ×11.5 5.170 0.646 0.573 297 B41866C5157M***
180 8 ×11.5 5.170 0.646 0.573 297 B41866C5187M***
220 8 ×11.5 5.170 0.646 0.573 297 B41866C5227M***
270 10 ×12.5 2.980 0.373 0.336 450 B41866C5277M***
330 10 ×12.5 2.980 0.373 0.336 450 B41866C5337M***
390 10 ×16 1.404 0.175 0.160 714 B41866C5397M***
470 10 ×16 1.404 0.175 0.160 714 B41866C5477M***
560 10 ×20 1.070 0.134 0.127 875 B41866C5567M***
680 10 ×20 1.070 0.134 0.127 875 B41866C5687M***
820 12.5 ×20 0.881 0.110 0.104 1105 B41866C5827M***
1000 12.5 ×20 0.881 0.110 0.104 1105 B41866C5108M***
1200 12.5 ×25 0.710 0.089 0.082 1358 B41866C5128M***
1500 12.5 ×25 0.710 0.089 0.082 1358 B41866C5158M***
1800 16 ×20 0.401 0.050 0.046 1895 B41866C5188M***
2200 12.5 ×40 0.406 0.051 0.047 2185 B41866C5228M***
2200 16 ×25 0.314 0.039 0.037 2279 B41866D5228M***
2200 18 ×20 0.341 0.043 0.040 2190 B41866E5228M***
2700 18 ×25 0.312 0.039 0.037 2454 B41866D5278M***
3300 16 ×31.5 0.248 0.031 0.029 2822 B41866D5338M***
3900 16 ×35.5 0.200 0.025 0.024 3230 B41866E5398M***
3900 18 ×31.5 0.224 0.028 0.027 3178 B41866D5398M***
4700 18 ×35 0.184 0.023 0.022 3638 B41866D5478M***
5600 18 ×40 0.152 0.019 0.018 4244 B41866C5568M***
B41866
High ripple current 125 °C
Page 9 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 35 V DC
100 8 ×11.5 5.170 0.646 0.573 297 B41866C7107M***
120 8 ×11.5 5.170 0.646 0.573 297 B41866C7127M***
150 10 ×12.5 2.980 0.373 0.336 450 B41866C7157M***
180 10 ×12.5 2.980 0.373 0.336 450 B41866C7187M***
220 10 ×12.5 2.980 0.373 0.336 450 B41866C7227M***
270 10 ×16 1.404 0.175 0.160 714 B41866C7277M***
330 10 ×16 1.404 0.175 0.160 714 B41866C7337M***
390 10 ×20 1.070 0.134 0.127 875 B41866C7397M***
470 10 ×20 1.070 0.134 0.127 875 B41866C7477M***
560 12.5 ×20 0.881 0.110 0.104 1105 B41866C7567M***
680 12.5 ×20 0.881 0.110 0.104 1105 B41866C7687M***
820 12.5 ×25 0.710 0.089 0.082 1358 B41866C7827M***
1000 16 ×20 0.401 0.050 0.046 1895 B41866C7108M***
1200 16 ×25 0.314 0.039 0.037 2279 B41866C7128M***
1500 16 ×25 0.314 0.039 0.037 2279 B41866C7158M***
1500 18 ×20 0.341 0.043 0.040 2190 B41866D7158M***
1800 16 ×31.5 0.249 0.031 0.029 2822 B41866C7188M***
1800 18 ×25 0.314 0.039 0.037 2454 B41866D7188M***
2200 16 ×35.5 0.200 0.025 0.024 3230 B41866D7228M***
2200 18 ×31.5 0.226 0.028 0.027 3178 B41866C7228M***
2700 18 ×35 0.187 0.023 0.022 3638 B41866C7278M***
3300 18 ×40 0.153 0.019 0.018 4244 B41866C7338M***
VR= 50 V DC
10 8 ×11.5 7.445 0.931 0.826 160 B41866C6106M***
12 8 ×11.5 7.445 0.931 0.826 160 B41866C6126M***
15 8 ×11.5 7.445 0.931 0.826 160 B41866C6156M***
18 8 ×11.5 7.445 0.931 0.826 160 B41866C6186M***
B41866
High ripple current 125 °C
Page 10 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 50 V DC
22 8 ×11.5 7.445 0.931 0.826 210 B41866C6226M***
27 8 ×11.5 7.445 0.931 0.826 210 B41866C6276M***
33 8 ×11.5 6.204 0.776 0.688 250 B41866C6336M***
39 8 ×11.5 6.204 0.776 0.688 250 B41866C6396M***
47 8 ×11.5 5.687 0.711 0.631 370 B41866C6476M***
56 8 ×11.5 5.429 0.679 0.602 370 B41866C6566M***
68 8 ×11.5 5.170 0.646 0.573 370 B41866C6686M***
82 8 ×11.5 5.170 0.646 0.573 370 B41866C6826M***
100 10 ×12.5 2.980 0.373 0.336 450 B41866C6107M***
120 10 ×16 1.404 0.175 0.160 714 B41866C6127M***
150 10 ×16 1.404 0.175 0.160 714 B41866C6157M***
180 10 ×20 1.070 0.134 0.127 875 B41866C6187M***
220 10 ×20 1.070 0.134 0.127 875 B41866C6227M***
270 10 ×20 1.070 0.134 0.127 875 B41866C6277M***
330 12.5 ×20 0.881 0.110 0.104 1105 B41866C6337M***
390 12.5 ×25 0.710 0.089 0.082 1358 B41866C6397M***
470 12.5 ×25 0.710 0.089 0.082 1358 B41866C6477M***
470 16 ×20 0.680 0.085 0.080 1370 B41866D6477M***
560 16 ×20 0.401 0.050 0.046 1895 B41866C6567M***
680 16 ×25 0.314 0.039 0.037 2279 B41866C6687M***
820 16 ×25 0.314 0.039 0.037 2279 B41866C6827M***
820 18 ×20 0.344 0.043 0.040 2190 B41866E6827M***
1000 16 ×31.5 0.249 0.031 0.029 2822 B41866C6108M***
1000 18 ×25 0.314 0.039 0.037 2454 B41866D6108M***
1200 16 ×35.5 0.200 0.025 0.024 3230 B41866D6128M***
1200 18 ×31.5 0.226 0.028 0.027 3178 B41866C6128M***
1500 18 ×35 0.187 0.023 0.022 3638 B41866C6158M***
1800 18 ×40 0.153 0.019 0.018 4244 B41866C6188M***
B41866
High ripple current 125 °C
Page 11 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 63 V DC
33 8 ×11.5 13.776 1.722 1.62 153 B41866C8336M***
39 10 ×12.5 4.456 0.557 0.533 309 B41866C8396M***
47 10 ×12.5 4.456 0.557 0.533 309 B41866C8476M***
56 10 ×12.5 4.456 0.557 0.533 309 B41866C8566M***
68 10 ×16 2.856 0.357 0.326 433 B41866C8686M***
82 10 ×16 2.856 0.357 0.326 433 B41866C8826M***
100 10 ×16 2.856 0.357 0.326 433 B41866C8107M***
120 10 ×16 2.856 0.357 0.326 433 B41866C8127M***
150 10 ×16 2.856 0.357 0.326 433 B41866C8157M***
180 10 ×20 1.920 0.240 0.244 546 B41866C8187M***
220 12.5 ×20 1.408 0.176 0.182 723 B41866C8227M***
270 12.5 ×20 1.408 0.176 0.182 723 B41866C8277M***
330 12.5 ×20 1.408 0.176 0.182 723 B41866C8337M***
390 12.5 ×25 0.936 0.117 0.116 989 B41866C8397M***
470 16 ×20 1.624 0.203 0.191 930 B41866C8477M***
560 16 ×20 1.624 0.203 0.191 930 B41866C8567M***
680 12.5 ×40 0.528 0.066 0.067 1588 B41866C8687M***
680 16 ×25 1.216 0.152 0.143 1165 B41866D8687M***
680 18 ×20 1.480 0.185 0.173 1052 B41866E8687M***
820 16 ×31.5 0.976 0.122 0.109 1461 B41866C8827M***
1000 16 ×31.5 0.976 0.122 0.109 1461 B41866C8108M***
1200 18 ×31.5 0.976 0.122 0.099 1645 B41866C8128M***
1500 18 ×35 0.752 0.094 0.085 1847 B41866C8158M***
1800 18 ×40 0.672 0.084 0.080 2015 B41866C8188M***
B41866
High ripple current 125 °C
Page 12 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 ... 12.5 ×25 mm and ∅16 ... 18 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 75 V DC
270 16 ×20 1.572 0.131 0.128 930 B41866C0277M***
330 16 ×25 1.260 0.105 0.103 1165 B41866C0337M***
330 18 ×20 1.488 0.124 0.121 1052 B41866D0337M***
470 16 ×31.5 0.900 0.075 0.073 1461 B41866C0477M***
470 18 ×25 1.044 0.087 0.085 1178 B41866D0477M***
680 18 ×31.5 0.768 0.064 0.062 1645 B41866C0687M***
820 18 ×35 0.672 0.056 0.054 1847 B41866C0827M***
1000 18 ×40 0.576 0.048 0.047 2015 B41866C0108M***
B41866
High ripple current 125 °C
Page 13 of 39Please read Cautions and warnings and
Important notes at the end of this document.
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Useful life
depending on ambient temperature TAunder ripple current operating conditions1)
d=8mmandVR≤63 VDC
Useful life
depending on ambient temperature TAunder ripple current operating conditions1)
d = 10 mm and VR≤63 VDC
B41866
High ripple current 125 °C
Page 14 of 39Please read Cautions and warnings and
Important notes at the end of this document.
2) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Useful life
depending on ambient temperature TAunder ripple current operating conditions2)
d≥12.5 mm and VR≤63 VDC
Useful life
depending on ambient temperature TAunder ripple current operating conditions2)
VR= 75 VDC
B41866
High ripple current 125 °C
Page 15 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Frequency factor of permissible ripple current IAC versus frequency f
B41866
High ripple current 125 °C
Page 16 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 18 mm as follows:
Lead spacing F = 2.0 mm (∅d=4 … 5 mm)
Lead spacing F = 2.5 mm (∅d=4 … 6.3 mm)
Lead spacing F = 3.5 mm (∅d = 8 mm)
Lead spacing F = 5.0 mm (∅d=4 … 12.5 mm)
Lead spacing F = 7.5 mm (∅d = 16 ... 18 mm).
Lead spacing 2.0 mm (∅d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆h D0
4 ... 5 2.0 18.5 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
B41866
High ripple current 125 °C
Page 17 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 2.5 mm (∅d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
∅d F H W W0W1W2H0P P0P1I1t∆h D0
4 ... 6.3 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
Toler-
rance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
Lead spacing 3.5 mm (∅d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆h D0
8 3.5 18.5 18.0 10 9.0 3.0 12.7 12.7 4.6 1.0 0.7 1.0 4.0
Toler-
ance
+0.8
0.2 ±1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.6 max. ±0.2 max. ±0.2
Leads can also run straight through the taping area. Taping is available up to dimensions
d×l=8×15 mm.
B41866
High ripple current 125 °C
Page 18 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 5.0 mm (∅d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (∅d = 10 ... 12.5 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
∅d F H W W0W1W2H0P P0P1I1t∆h D0
4 ...
6.3 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.6 1.0 4.0
820.0 10.0 16.0 12.7 12.7 3.85
10 5.0 19.0 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.6 1.0 4.0
12.5 19.0 12.5 15.0 15.0 5.0
Toler-
ance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. +0.3
0.2 max. ±0.2
Taping is available up to dimensions d ×l=10×31.5 mm and 12.5 ×25 mm.
Taping is not available for d ×l=8×20 mm.
B41866
High ripple current 125 °C
Page 19 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 7.5 mm (∅d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆P∆h D0
16 7.5 18.5 18.0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0
18
Toler-
ance ±0.8 0.5
+0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2
Taping is available up to dimensions d ×l=16×31.5 mm and 18 ×31.5 mm.
B41866
High ripple current 125 °C
Page 20 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Cut or kinked leads
Single-ended capacitors are available with cut or kinked leads. Other lead configurations also
available upon request.
Cut leads (Chapter A)
Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086,
B43088, B43827, B43828.
Last 3 digits of ordering code: 002
Case size d x l (mm) Dimensions
(mm)
a±0.5
4 x 7 1.5
5 x 7 2.0
5 x 11 2.0
6.3 x 7 2.5
6.3 x 11 2.5
8 x 7 3.5
8 x 11.5 3.5
8 x 15 3.5
8 x 20 3.5
10 x 12.5 5.0
10 x 16 5.0
10 x 20 5.0
10 x 25 5.0
10 x 31.5 5.0
Case size d x l (mm) Dimensions
(mm)
a±0.5
12.5 x 16 5.0
12.5 x 20 5.0
12.5 x 25 5.0
12.5 x 31.5 5.0
12.5 x 35.5 5.0
12.5 x 40 5.0
16 x 20 7.5
16 x 25 7.5
16 x 31.5 7.5
16 x 35.5 7.5
16 x 40 7.5
18 x 20 7.5
18 x 25 7.5
18 x 31.5 7.5
18 x 35.5 7.5
18 x 40 7.5
B41866
High ripple current 125 °C
Page 21 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Cut leads (Chapter B)
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Last 3 digits of ordering code: 002
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×12.5 5.0
10 ×16 5.0
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
16 ×35.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B41866
High ripple current 125 °C
Page 22 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Kinked leads (Chapter A)
Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086,
B43088, B43827, B43828.
Last 3 digits of ordering code: 001
Case size d x l (mm) Dimensions
(mm)
a±0.5
4 x 7 1.5
5 x 7 2.0
5 x 11 2.0
6.3 x 7 2.5
6.3 x 11 2.5
8 x 7 3.5
8 x 11.5 3.5
8 x 15 3.5
8 x 20 3.5
10 x 12.5 5.0
10 x 16 5.0
10 x 20 5.0
10 x 25 5.0
10 x 31.5 5.0
Case size d x l (mm) Dimensions
(mm)
a±0.5
12.5 x 16 5.0
12.5 x 20 5.0
12.5 x 25 5.0
12.5 x 31.5 5.0
12.5 x 35.5 5.0
12.5 x 40 5.0
16 x 20 7.5
16 x 25 7.5
16 x 31.5 7.5
16 x 35.5 7.5
16 x 40 7.5
18 x 20 7.5
18 x 25 7.5
18 x 31.5 7.5
18 x 35.5 7.5
18 x 40 7.5
B41866
High ripple current 125 °C
Page 23 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Kinked leads (Chapter B)
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Last 3 digits of ordering code: 001
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
16 ×35.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B41866
High ripple current 125 °C
Page 24 of 39Please read Cautions and warnings and
Important notes at the end of this document.
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 18 mm.
There are three configurations available: Crimped leads, J leads, bent 90°leads
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal With flat rubber seal
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 a ±0.5 ∅b
16 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×35.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
18 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
B41866
High ripple current 125 °C
Page 25 of 39Please read Cautions and warnings and
Important notes at the end of this document.
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 J ±0.2 a ±0.5 ∅b
10 ×12.5 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×16 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×25 3.2 0.7 1.2 5.0 0.6 ±0.05
16 ×20 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×25 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×35.5 3.5 0.7 1.6 7.5 0.8 ±0.05
18 ×20 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×25 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×35 3.5 0.7 1.6 7.5 0.8 ±0.1
B41866
High ripple current 125 °C
Page 26 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Bent 90°leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 ∅b
16 ×20 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×25 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×31.5 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×35.5 4.0 4.0 12.0 7.5 0.8 ±0.05
18 ×20 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×25 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×31.5 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×35 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×40 4.0 4.0 13.0 7.5 0.8 ±0.1
Bent leads for diameter 12.5 mm available upon request.
B41866
High ripple current 125 °C
Page 27 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Packing units and box dimensions
Ammo pack
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
4×7 330 50 196 2000
5×7 330 50 226 2000
5×11 330 50 226 2000
6.3 ×7 330 50 286 2000
6.3 ×11 330 50 286 2000
8×7 330 50 246 1000
8×11.5 330 50 246 1000
8×15 330 50 246 500
10 ×12.5 330 50 196 500
10 ×16 330 54 196 500
10 ×20 330 58 196 500
12.5 ×20 341 60 272 500
12.5 ×25 341 65 272 500
16 ×25 320 65 270 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B41866
High ripple current 125 °C
Page 28 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Ammo pack
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
8×11.5 345 55 240 1000
10 ×12.5 345 55 280 750
10 ×16 345 60 200 500
10 ×20 345 60 200 500
12.5 ×20 345 65 280 500
12.5 ×25 345 65 280 500
16 ×20 315 65 275 300
16 ×25 315 65 275 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B41866
High ripple current 125 °C
Page 29 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 4 x 7 ... 16 x 40
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
dxl
mm
Standard,
bulk
pcs.
Taped,
Ammo pack
pcs.
Kinked leads,
bulk
pcs.
Cut leads,
bulk
pcs.
4 x 7 10000 2000 15000 15000
5 x 7 7500 2000 10000 10000
5 x 11 5000 2000 10000 10000
6.3 x 7 5000 2000 10000 10000
6.3 x 11 5000 2000 5000 5000
8 x 7 5000 1000 5000 5000
8 x 11.5 2500 1000 4000 4000
8 x 15 2000 1000 2500 2500
8 x 20 1500 2000 2000
10 x 12.5 2000 500 2500 2500
10 x 16 1500 500 2000 2000
10 x 20 1000 500 1500 1500
10 x 25 1000 500 1250 1250
12.5 x 16 750 500 1000 1000
12.5 x 20 750 500 500 500
12.5 x 25 750 500 500 500
12.5 x 31.5 500 750 750
12.5 x 35.5 500 750 750
12.5 x 40 500 750 750
16 x 20 375 300 500 500
16 x 25 375 300 500 500
16 x 31.5 250 300 375 375
16 x 35.5 250 375 375
16 x 40 250 375 375
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002
006
007
008
009
016
3.5
2.5
5.0
7.5
2.0
8
4 ... 6.3
4 ... 12.5
16 ... 18
4 ... 5
B41866
High ripple current 125 °C
Page 30 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 x 20 ... 18 x 40
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
dxl
mm
Standard,
bulk
pcs.
Taped,
Ammo pack
pcs.
Kinked leads,
bulk
pcs.
Cut leads,
bulk
pcs.
18 x 20 250 250 100 100
18 x 25 250 250 100 100
18 x 31.5 250 250 100 100
18 x 35.5 250 100 100
18 x 40 250 100 100
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002
009 7.5 16 ... 18
B41866
High ripple current 125 °C
Page 31 of 39Please read Cautions and warnings and
Important notes at the end of this document.
1) Available upon request
Overview of packing units and code numbers for case sizes 8 ×11.5 ... 16 ×35.5
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
8×11.5 1000 1000
10 ×12.5 1000 750 1000 675
10 ×16 1000 500 1000 675
10 ×20 500 500 500 500 500
12.5 ×20 350 500 350 350 300 1)
12.5 ×25 250 500 500 500 225 1)
12.5 ×30 200
12.5 ×35 175
12.5 ×40 175
16 ×20 250 300 200 200 200 200 120
16 ×25 250 300 200 200 200 200 120
16 ×31.5 200 300 250 250 344 344 120
16 ×35.5 100 100 100 150 150 150
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
006
008
009
3.5
5
7.5
8
5...12.5
16...18
B41866
High ripple current 125 °C
Page 32 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 ×20 ... 18 ×40
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
18 ×20 175 250 175 175 200 200 120
18 ×25 150 250 150 150 200 200 120
18 ×31.5 100 250 100 100 150 150 120
18 ×35 100 100 100 150 150 150
18 ×40 125 100 100 120 72
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
009 7.5 16...18
B41866
High ripple current 125 °C
Page 33 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling aluminum electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
B41866
High ripple current 125 °C
Page 34 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Product safety
The table below summarizes the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic Safety information Reference
chapter "General
technical information"
Polarity Make sure that polar capacitors are connected
with the right polarity.
1
"Basic construction of
aluminum electrolytic
capacitors"
Reverse voltage Voltages polarity classes should be prevented by
connecting a diode.
3.1.6
"Reverse voltage"
Upper category
temperature
Do not exceed the upper category temperature. 7.2
"Maximum permissible
operating temperature"
Maintenance Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
10
"Maintenance"
Mounting
position of screw-
terminal capacitors
Do not mount the capacitor with the terminals
(safety vent) upside down.
11.1.
"Mounting positions of
capacitors with screw
terminals"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
11.4
"Mounting
considerations for
single-ended capacitors"
Robustness of
terminals
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
11.3
"Mounting torques"
Soldering Do not exceed the specified time or temperature
limits during soldering.
11.5
"Soldering"
B41866
High ripple current 125 °C
Page 35 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Topic Safety information Reference
chapter "General
technical information"
Soldering,
cleaning agents
Do not allow halogenated hydrocarbons to come
into contact with aluminum electrolytic capacitors.
11.6
"Cleaning agents"
Passive
flammability
Avoid external energy, such as fire or electricity. 8.1
"Passive flammability"
Active
flammability
Avoid overload of the capacitors. 8.2
"Active flammability"
Reference
chapter "Capacitors with
screw terminals"
Breakdown strength
of insulating
sleeves
Do not damage the insulating sleeve, especially
when ring clips are used for mounting.
"Screw terminals
accessories"
B41866
High ripple current 125 °C
Page 36 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Symbols and terms
Symbol English German
C Capacitance Kapazität
CRRated capacitance Nennkapazität
CSSeries capacitance Serienkapazität
CS,T Series capacitance at temperature T Serienkapazität bei Temperatur T
CfCapacitance at frequency f Kapazität bei Frequenz f
d Case diameter, nominal dimension Gehäusedurchmesser, Nennmaß
dmax Maximum case diameter Maximaler Gehäusedurchmesser
ESL Self-inductance Eigeninduktivität
ESR Equivalent series resistance Ersatzserienwiderstand
ESRfEquivalent series resistance at
frequency f
Ersatzserienwiderstand bei Frequenz f
ESRTEquivalent series resistance at
temperature T
Ersatzserienwiderstand bei Temperatur T
f Frequency Frequenz
I Current Strom
IAC Alternating current (ripple current) Wechselstrom
IAC,rms Root-mean-square value of alternating
current
Wechselstrom, Effektivwert
IAC,f Ripple current at frequency f Wechselstrom bei Frequenz f
IAC,max Maximum permissible ripple current Maximal zulässiger Wechselstrom
IAC,R Rated ripple current Nennwechselstrom
IAC,R (B) Rated ripple current for base cooling Nennwechselstromstrom für Bodenkühlung
Ileak Leakage current Reststrom
Ileak,op Operating leakage current Betriebsreststrom
l Case length, nominal dimension Gehäuselänge, Nennmaß
lmax Maximum case length (without
terminals and mounting stud)
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
R Resistance Widerstand
Rins Insulation resistance Isolationswiderstand
Rsymm Balancing resistance Symmetrierwiderstand
T Temperature Temperatur
∆T Temperature difference Temperaturdifferenz
TAAmbient temperature Umgebungstemperatur
TCCase temperature Gehäusetemperatur
TBCapacitor base temperature Temperatur des Becherbodens
t Time Zeit
∆t Period Zeitraum
tbService life (operating hours) Brauchbarkeitsdauer (Betriebszeit)
B41866
High ripple current 125 °C
Page 37 of 39Please read Cautions and warnings and
Important notes at the end of this document.
Symbol English German
V Voltage Spannung
VFForming voltage Formierspannung
Vop Operating voltage Betriebsspannung
VRRated voltage, DC voltage Nennspannung, Gleichspannung
VSSurge voltage Spitzenspannung
XCCapacitive reactance Kapazitiver Blindwiderstand
XLInductive reactance Induktiver Blindwiderstand
Z Impedance Scheinwiderstand
ZTImpedance at temperature T Scheinwiderstand bei Temperatur T
tan δDissipation factor Verlustfaktor
λFailure rate Ausfallrate
ε0Absolute permittivity Elektrische Feldkonstante
εrRelative permittivity Dielektrizitätszahl
ωAngular velocity; 2 πf Kreisfrequenz; 2 πf
Note
All dimensions are given in mm.
B41866
High ripple current 125 °C
Page 38 of 39Please read Cautions and warnings and
Important notes at the end of this document.
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-
tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the "General Terms of Delivery for Products and Services in the Electrical In-
dustry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap,
DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKK, MKD, MLSC, MotorCap, PCC,
PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trade-
marks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
Important notes
Page 39 of 39
