Preliminary Revised November 2001 FSTD16244 16-Bit Bus Switch with Level Shifting (Preliminary) General Description Features The Fairchild Switch FSTD16244 provides 16-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. A diode to VCC has been integrated into the circuit to allow for level shifting between 5V inputs and 3.3V outputs. 4 switch connection between two ports. The device is organized as a 16-bit switch. There are four 4-bit switches with separate output enable inputs. When OE is LOW, the switch in ON and Port A is connected to Port B. When OE is HIGH, the switch OFF and a high impedance state exists between the A and B Ports. Minimal propagation delay through the switch. Low lCC. Zero bounce in flow-through mode. Control inputs compatible with TTL level. TruTranslation voltage translation from 5.0V inputs to 3.3V outputs Ordering Code: Order Number FSTD16244MTD Package Number Package Description MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Devices also available in Tape and Reel. Specify by appending the suffix letter "X" to the ordering code. TruTranslation is trademark of Fairchild Semiconductor Corporation. (c) 2001 Fairchild Semiconductor Corporation DS500693 www.fairchildsemi.com FSTD16244 16-Bit Bus Switch with Level Shifting (Preliminary) November 2001 FSTD16244 Preliminary Connection Diagram Logic Diagram Pin Descriptions Truth Table Pin Name Description Inputs OEn Output Enable Input (Active LOW) OEx A, B 1An, 2An, 3An, 4An Bus A L A Port = B Port 1Bn, 2Bn, 3Bn, 4Bn Bus B H H = HIGH Voltage Level www.fairchildsemi.com Outputs 2 Z L = LOW Voltage Level Z = High Impedance Preliminary Recommended Operating Conditions (Note 4) Supply Voltage (VCC) -0.5V to +7.0V DC Switch Voltage (VS) (Note 2) -0.5V to +7.0V Power Supply Operating (VCC) DC Input Voltage (VIN) (Note 3) -0.5V to +7.0V Input Voltage (VIN) 0V to 5.5V 0V to 5.5V DC Input Diode Current (lIK) VIN < 0V -50mA Output Voltage (VOUT) DC Output (IOUT) Current 128mA Input Rise and Fall Time (tr, tf) 100mA DC VCC/GND Current (ICC/IGND) Storage Temperature Range (TSTG) 4.5V to 5.5V Switch Control Input -65C to +150 C 0 ns/V to 5 ns/V Switch I/O 0 ns/V to DC -40C to +85C Free Air Operating Temperature (TA) Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The "Recommended Operating Conditions" table will define the conditions for actual device operation. Note 2: VS is the voltage observed/applied at either the A or B Ports across the switch. Note 3: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 4: Unused control inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics TA = -40C to +85C Symbol Parameter VCC Min Typ (V) VIK Clamp Diode Voltage VIH HIGH Level Input Voltage 4.5 - 5.5 VIL LOW Level Input Voltage 4.5 - 5.5 VOH HIGH Level 4.5 - 5.5 II Input Leakage Current 4.5 -1.2 V 2.0 1.0 A 0 VIN 5.5V 0 10 A VIN = 5.5V 1.0 A 0 A, B VCC 7 VIN = 0V, IIN = 64mA VIN = 0V, IIN = 30mA 5.5 Switch On Resistance 4.5 See Figure 3 4 V 4.5 4 7 4.5 35 50 Quiescent Supply Current 1.5 mA 10 A 2.5 mA 5.5 Increase in ICC per Input IIN = -18mA V 5.5 OFF-STATE Leakage Current ICC Conditions V IOZ ICC Units 0.8 RON (Note 6) Max (Note 5) 5.5 VIN = 2.4V, IIN = 15mA OEn = GND VIN = VCC or GND, IOUT = 0 OEn = VCC VIN = VCC or GND, IOUT = 0 One Input at 3.4V Other Inputs at VCC or GND Note 5: Typical values are at VCC = 5.0V and TA = +25C Note 6: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B) pins. 3 www.fairchildsemi.com FSTD16244 Absolute Maximum Ratings(Note 1) FSTD16244 Preliminary AC Electrical Characteristics TA = -40 C to +85 C, Symbol Parameter CL = 50pF, RU = RD = 500 Min tPHL, tPLH Propagation Delay Bus-to-Bus (Note 7) tPZH, tPZL Output Enable Time Units VCC = 4.5 - 5.5V Conditions Max 1.0 0.25 ns 5.1 ns VI = OPEN Figures 1, 2 VI = 7V for tPZL Figures 1, 2 VI = OPEN for tPZH tPHZ, tPLZ Output Disable Time Figure Number 1.0 5.4 ns VI = 7V for tPLZ Figures 1, 2 VI = OPEN for tPHZ Note 7: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage source (zero output impedance). Capacitance Symbol (Note 8) Parameter Typ Max Units Conditions CIN Control Pin Input Capacitance 3 pF VCC = 5.0V, VIN = 0V CI/O Input/Output Capacitance "OFF State" 6 pF VCC, OE = 5.0V, VIN = 0V Note 8: TA = +25C, f = 1 MHz, Capacitance is characterized but not tested. AC Loading and Waveforms Note: Input driven by 50 source terminated in 50 Note: CL includes load and stray capacitance Note: Input PRR = 1.0 MHz, tW = 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms www.fairchildsemi.com 4 Preliminary FSTD16244 Output Voltage HIGH vs. Supply Voltage FIGURE 3. 5 www.fairchildsemi.com FSTD16244 16-Bit Bus Switch with Level Shifting (Preliminary) Preliminary Physical Dimensions inches (millimeters) unless otherwise noted 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD48 Technology Description The Fairchild Switch family derives from and embodies Fairchild's proven switch technology used for several years in its 74LVX3L384(FST3384) bus switch product. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 6