CSM_CJ1W-OUTPUT_DS_E_8_1
1
CJ-series Output Units
CJ1W-OC/OA/OD
A Wide Range of Basic Output
Units for High Speed Output
and Different Applications
• These Output Units receive the results of
output instructions from the CPU Unit and
perform ON/OFF control for external devices.
• High-speed Output models CJ1W-OD213 and
CJ1W-OD234 can help to increase system
throughput.
Features
•High-speed output models are available, meeting versatile applications.
ON Response Time: 15μs, OFF Response Time: 80μs
•Output Units are available with any of three output types: relay contact outputs, triac outputs, or transistor outputs.
•For transistor outputs, select from sinking outputs or sourcing outputs.
•Output Units with load short-circuit protection are also available. *1
•Select the best interface for each application: Fujitsu connectors or MIL connectors. *2
•A wide variety of Connector-Terminal Block Conversion Units are available to allow you to easily wire external output devices.
*1. The following Units have load short-circuit protection: CJ1W-OC202, CJ1W-OD204, CJ1W-OD212, and CJ1W-OD232.
*2. Available for models with 32 outputs or 64 outputs
CJ1W-OD213 CJ1W-OD234
CJ1W-OC/OA/OD
2
Ordering Information
International Standards
• The standards are abbreviated as follows: U: UL, U1: UL (Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2
Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, and CE: EC Directives.
• Contact your OMRON representative for further details and applicable conditions for these standards.
Output Units
Accessories
Connectors are not included for models with connectors. Either use one of the applicable connector listed below or use an applicable Connector-
Terminal Block Conversion Unit or I/O Relay Terminal. For details on wiring methods, refer to External Interface.
Unit type Product
name
Specifications No. of
words
allocated
Current
consumption
(A) Model Standards
Output
type
I/O
points
Maximum switching
capacity Commons External
connection 5 V 24 V
CJ1
Basic
I/O Units
Relay
Contact
Output Units −8
outputs 250 VAC/24 VDC, 2 A Independen
t contacts
Removable
terminal
block
1 words 0.09 0.048
max. CJ1W-OC201
UC1, N, L,
CE
−16
outputs 250 VAC/24 VDC, 2 A 16 points,
1 common
Removable
terminal
block
1 words 0.11 0.096
max. CJ1W-OC211
Triac Output
Unit
−8
outputs 250 VAC, 0.6 A 8 points,
1 common
Removable
terminal
block
1 words 0.22 −CJ1W-OA201
Transistor
Output Units
Sinking 8
outputs 12 to 24 VDC, 2 A 4 points,
1 common
Removable
terminal
block
1 words 0.09 −CJ1W-OD201
Sinking 8
outputs 12 to 24 VDC, 0.5 A 8 points,
1 common
Removable
terminal
block
1 words 0.10 −CJ1W-OD203
Sinking 16
outputs 12 to 24 VDC, 0.5 A 16 points,
1 common
Removable
terminal
block
1 words 0.10 −CJ1W-OD211
Sinking
16
outputs
(High
speed)
24 VDC, 0.5 A 16 points,
1 common
Removable
terminal
block
1 words 0.15 −CJ1W-OD213 N, L, CE
Sinking 32
outputs 12 to 24 VDC, 0.5 A 16 points,
1 common
Fujitsu
connector 2 words 0.14 −CJ1W-OD231 UC1, N, L,
CE
Sinking 32
outputs 12 to 24 VDC, 0.5 A 16 points,
1 common
MIL
connector 2 words 0.14 −CJ1W-OD233
Sinking
32
outputs
(High
speed)
24 VDC, 0.5 A 16 points,
1 common
MIL
connector 2 words 0.22 −CJ1W-OD234 N, L, CE
Sinking 64
outputs 12 to 24 VDC, 0.3 A 16 points,
1 common
Fujitsu
connector 4 words 0.17 −CJ1W-OD261
UC1, N, L,
CE
Sinking 64
outputs 12 to 24 VDC, 0.3 A 16 points,
1 common
MIL
connector 4 words 0.17 −CJ1W-OD263
Sourcing 8
outputs
24 VDC, 2 A
Short-circuit protection
4 points,
1 common
Removable
terminal
block
1 words 0.11 −CJ1W-OD202
Sourcing 8
outputs
24 VDC, 0.5 A
Short-circuit protection
8 points,
1 common
Removable
terminal
block
1 words 0.10 −CJ1W-OD204
Sourcing 16
outputs
24 VDC, 0.5 A
Short-circuit protection
16 points,
1 common
Removable
terminal
block
1 words 0.10 −CJ1W-OD212
Sourcing 32
outputs
24 VDC, 0.5 A
Short-circuit protection
16 points,
1 common
MIL
connector 2 words 0.15 −CJ1W-OD232
Sourcing 64
outputs 12 to 24 VDC, 0.3 A 16 points,
1 common
MIL
connector 4 words 0.17 −CJ1W-OD262
3
CJ1W-OC/OA/OD
Applicable Connectors
Fujitsu Connectors for 32-input, 32-output, 64-input, 64-output, 32-input/32-output, and 16-input/16-output Units
MIL Connectors for 32-input, 32-output, 64-input, 64-output, 32-input/32-output, and 16-input/16-output Units
* Crimp Contacts are also required. Refer to page 31 for details.
Applicable Connector-Terminal Block Conversion Units
Note: For the combination of Output Units with Connector-Terminal Block Conversion Units, refer to 2. Connecting Connector-Terminal Block
Conversion Units.
Name Connection Remarks Applicable Units Model Standards
40-pin
Connectors
Soldered FCN-361J040-AU Connector
FCN-360C040-J2 Connector Cover Fujitsu Connectors:
CJ1W-ID231(32 inputs): 1 per Unit
CJ1W-ID261 (64 inputs): 2 per Unit
CJ1W-OD231 (32 outputs): 1 per Unit
CJ1W-OD261 (64 outputs): 2 per Unit
CJ1W-MD261 (32 inputs, 32 outputs): 2 per Unit
C500-CE404
−
Crimped
FCN-363J040 Housing
FCN-363J-AU Contactor
FCN-360C040-J2 Connector Cover
C500-CE405
Pressure welded FCN-367J040-AU/F C500-CE403
24-pin
Connectors
Soldered FCN-361J024-AU Connector
FCN-360C024-J2 Connector Cover
Fujitsu Connectors:
CJ1W-MD231 (16 inputs, 16 outputs): 2 per Unit
C500-CE241
Crimped
FCN-363J024 Socket
FCN-363J-AU Contactor
FCN-360C024-J2 Connector Cover
C500-CE242
Pressure welded FCN-367J024-AU/F C500-CE243
Name Connection Remarks Applicable Units Model Standards
40-pin
Connectors
Pressure welded FRC5-AO40-3TOS MIL Connectors:
CJ1W-ID232/233 (32 inputs): 1 per Unit
CJ1W-OD232/233/234 (32 outputs):1 per Unit
CJ1W-ID262 (64 inputs): 2 per Unit
CJ1W-OD262/263 (64 outputs): 2 per Unit
CJ1W-MD263/563 (32 inputs, 32 outputs): 2 per Unit
XG4M-4030-T
−
Crimped −XG5N-401*
20-pin
Connectors
Pressure welded FRC5-AO20-3TOS MIL Connectors:
CJ1W-MD232/233 (16 inputs, 16 outputs): 2 per Unit
XG4M-2030-T −
Crimped −XG5N-201*
Type Series I/O Number
of poles Wiring method Terminal
type
Size Mounting Common
terminals
Bleeder
resistance Indicators I/O Units Model Standards
Depth
(mm)
Height
(mm)
Width
(mm)
DIN
Track Screws
PLCs
XW2R Output 34
Phillips screw
M3 50
48.35 130.7
Yes Yes No No No
CJ1W-OD231
CJ1W-OD261
XW2R-J34G-C3
−
CJ1W-OD232
CJ1W-OD233
CJ1W-OD234
CJ1W-OD262
CJ1W-OD263
XW2R-J34G-C4
Slotted screw
(rise up)
M3
(European
type)
50
45.11
98.5
CJ1W-OD231
CJ1W-OD261
XW2R-E34G-C3
CJ1W-OD232
CJ1W-OD233
CJ1W-OD234
CJ1W-OD262
CJ1W-OD263
XW2R-E34G-C4
Push-in
spring
Clamp 50
45.11
98.5
CJ1W-OD231
CJ1W-OD261
XW2R-P34G-C3
CJ1W-OD232
CJ1W-OD233
CJ1W-OD234
CJ1W-OD262
CJ1W-OD263
XW2R-P34G-C4
CJ1W-OC/OA/OD
4
Applicable I/O Relay Terminals
Note: For the combination of Output Units with I/O Relay Terminal and Connecting Cables, refer to 3. Connecting I/O Relay Terminals.
Type Series
Specifications Size (horizontal
mounting) Mounting
Model
Standrads
Classification
Polarity
Number
of
points
Rated ON
current at
contacts
Operation
indicators
Terminal
block for
power
supply
wiring
Horizontal
(mm)
Vertical
(mm)
Height
(mm)
DIN
Track Screws
Space-
saving
G70D
Vertical
type
G70D-V
Outputs
Relay
outputs
NPN
16
(SPST-
NO
×
16)
5A or 3A
Yes
Expandable
135 46 81 Yes Yes
G70D-VSOC16
U, C,
CE
MOSFET
relay
outputs
0.3A
G70D-VFOM16
Flat
type
G70D
Relay
outputs
NPN
8 (SPST-
NO
×
8)
5A
Yes −
68 93 44
Yes Yes
G70D-SOC08
−
16
(SPST-
NO
×
16)
3A
156 51 39
G70D-SOC16
−
PNP
16
(SPST-
NO
×
16)
3A
G70D-SOC16-1
MOSFET
relay
outputs
NPN
16
(SPST-
NO
×
16)
0.3A
G70D-FOM16
−
PNP
G70D-FOM16-1
High-
capacity,
space-
saving
G70R
Outputs Relay
outputs
NPN
8 (SPST-
NO
×
8)
10A Yes −136 93 55 Yes Yes
G70R-SOC08
−
Standard
G7TC
Inputs
AC
inputs
NPN
16
(SPST-
NO
×
16)
1A
Yes −
182
85 68 Yes −
G7TC-IA16
U, C
DC
inputs
G7TC-ID16
Outputs Relay
outputs
NPN
8 (SPST-
NO
×
8)
5A
102
G7TC-OC08
16
(SPST-
NO
×
16)
182
G7TC-OC16
PNP
16
(SPST-
NO
×
16)
G7TC-OC16-1
−
High-
capacity
socket
G70A
(Socket only)
Outputs Relay
outputs
NPN
16
(SPDT
×
16
possible
with G2R
Relays)
10 A
(Terminal
block
allowable
current)
No −234 75 64 Yes −
G70A-ZOC16-3
U, C,
CE
(Socket only) +
Relay/SSR/
MOSFET Relay/
Timer
PNP
G70A-ZOC16-4
(Socket only) +
Relay/SSR/
MOSFET Relay/
Timer
5
CJ1W-OC/OA/OD
Mountable Racks
Model
NJ system CJ system (CJ1, CJ2) CP1H system NSJ system
CPU Rack Expansion Rack CPU Rack Expansion
Backplane CP1H PLC NSJ Controller Expansion
Backplane
CJ1W-OC201
10 Units
10 Units
(Per Expansion
Rack)
10 Units
10 Units
(Per Expansion
Backplane)
Not Supported Not Supported
10 Units
(Per Expansion
Backplane)
CJ1W-OC211
CJ1W-OA201
CJ1W-OD201
CJ1W-OD203
CJ1W-OD211
CJ1W-OD213
CJ1W-OD231
CJ1W-OD233
CJ1W-OD234
CJ1W-OD261
CJ1W-OD263
CJ1W-OD202
CJ1W-OD204
CJ1W-OD212
CJ1W-OD232
CJ1W-OD262
CJ1W-OC/OA/OD
6
Specifications
CJ1W-OC201 Contact Output Unit (Independent Relays, 8 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.
Name 8-point Contact Output Unit with Terminal Block (Independent Relays)
Model CJ1W-OC201
Max. Switching
Capacity 2 A 250 VAC (cosφ = 1), 2 A 250 VAC (cosφ = 0.4), 2 A 24 VDC (16 A/Unit)
Min. Switching
Capacity 1 mA 5 VDC
Relays NY-24W-K-IE (Fujitsu Takamizawa Components, Ltd.), Cannot be replaced.
Service Life of Relay
Electrical: 150,000 operations (24 VDC, resistive load)/100,000 operations (240 VAC, cosφ = 0.4, inductive load)
Mechanical: 20,000,000 operations
Service life will vary depending on the connected load.
ON Response Time 15 ms max.
OFF Response Time 15 ms max.
Number of Circuits 8 independent contacts
Insulation Resistance
20 MΩ between external terminals and the GR terminal (500 VDC)
Dielectric Strength 2,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Internal Current
Consumption
90 mA 5 VDC max.
48 mA 24 VDC max. (6 mA × No. of ON points)
Weight 140 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
•The input power supply polarity can be connected in either direction.
Output indicator
Internal circuits
Signal
name
Jxx_Ch1_Out00
Jxx_Ch1_Out00
2 A 250 VAC,
2 A 24 VDC max.
Signal
name
Signal
name
Connec-
tor pin *
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
B0
A0
L
L
L
L
L
L
L
L
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
NC
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
NC
7
CJ1W-OC/OA/OD
CJ1W-OC211 Contact Output Unit (16 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Name 16-point Contact Output Unit with Terminal Block
Model CJ1W-OC211
Max. Switching
Capacity 2 A 250 VAC (cosφ = 1), 2 A 250 VAC (cosφ = 0.4), 2 A 24 VDC (8 A/Unit)
Min. Switching
Capacity 1 mA 5 VDC
Relays NY-24W-K-IE (Fujitsu Takamizawa Components, Ltd.), Cannot be replaced.
Service Life of Relay
Electrical: 150,000 operations (24 VDC, resistive load)/ 100,000 operations (250 VAC, cosφ = 0.4, inductive load)
Mechanical: 20,000,000 operations
Service life will vary depending on the connected load.
ON Response Time 15 ms max.
OFF Response Time 15 ms max.
Number of Circuits 16 points/common, 1 circuit
Insulation Resistance
20 MΩ between external terminals and the GR terminal (500 VDC)
Dielectric Strength 2,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Internal Current
Consumption
110 mA 5 VDC max.
96 mA 24 VDC max. (6 mA × No. of ON points)
Weight 170 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
Internal circuits
to
Signal
name
Jxx_Ch1_Out15
Jxx_Ch1_Out00
COM
COM
2 A 250 VAC,
2 A 24 VDC max.
Signal
name
Signal
name
Connec-
tor pin
*
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
B0
A0
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch1_Out01
Jxx_Ch1_Out03
Jxx_Ch1_Out05
Jxx_Ch1_Out07
Jxx_Ch1_Out09
Jxx_Ch1_Out11
Jxx_Ch1_Out13
Jxx_Ch1_Out15
Jxx_Ch1_Out00
Jxx_Ch1_Out02
Jxx_Ch1_Out04
Jxx_Ch1_Out06
Jxx_Ch1_Out08
Jxx_Ch1_Out10
Jxx_Ch1_Out12
Jxx_Ch1_Out14
COM
COM
CJ1W-OC/OA/OD
8
CJ1W-OA201 Triac Output Unit (8 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.
Name 8-point Triac Output Unit with Terminal Block
Model CJ1W-OA201
Max. Switching
Capacity 0.6 A 250 VAC, 50/60 Hz (2.4 A/Unit)
Max. Inrush Current 15 A (pulse width: 10 ms max.)
Min. Switching
Capacity 50 mA 75 VAC
Leakage Current 1.5 mA (200 VAC) max.
Residual Voltage 1.6 VAC max.
ON Response Time 1 ms max.
OFF Response Time 1/2 of load frequency + 1 ms or less.
Number of Circuits 8 (8 points/common, 1 circuit)
Surge Protector C.R Absorber + Surge Absorber
Fuses 5 A (1/common, 1 used)
The fuse cannot be replaced by the user.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (500 VDC)
Dielectric Strength 2,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Internal Current
Consumption 220 mA max.
Weight 150 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
Internal circuits
Fuse
to
Signal
name
COM
Jxx_Ch1_Out00
Jxx_Ch1_Out07
250 VAC max.
Signal
name
Connec-
tor pin *
B0
B1
B2
B3
B4
B5
B6
B7
B8
A0
A1
A2
A3
A4
A5
A6
A7
A8
NC
NC
NC
NC
NC
NC
NC
NC
NC
L
L
L
L
L
L
L
L
COM
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
9
CJ1W-OC/OA/OD
CJ1W-OD201 Transistor Output Unit (8 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.
Name 8-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model CJ1W-OD201
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 2.0 A/point, 8.0 A/Unit
Maximum Inrush
Current 10 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 8 (4 points/common, 2 circuits)
Internal Current
Consumption 90 mA max.
Fuse 6.3 A (1/common, 2 used)
The fuse cannot be replaced by the user.
External Power
Supply 12 to 24 VDC, 10 mA min.
Weight 110 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Internal circuits
Output indicator
Fuse
Fuse
to
to
Signal name
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out03
COM0
Jxx_Ch1_Out04
+V
Jxx_Ch1_Out07
COM1
12 to 24 VDC
12 to 24 VDC
Signal
name
Signal
name
Connec-
tor pin
*
B0
B1
B2
B3
B4
B5
B6
B7
B8
A0
A1
A2
A3
A4
A5
A6
A7
A8
L
L
L
L
L
L
L
LJxx_Ch1_Out00
Jxx_Ch1_Out02
COM0
NC
NC
Jxx_Ch1_Out04
Jxx_Ch1_Out06
NC
Jxx_Ch1_Out01
Jxx_Ch1_Out03
+V
NC
NC
NC
Jxx_Ch1_Out05
Jxx_Ch1_Out07
COM1
+V
CJ1W-OC/OA/OD
10
CJ1W-OD203 Transistor Output Unit (8 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.
Name 8-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model CJ1W-OD203
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 4.0 A/Unit
Maximum Inrush
Current 4.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.1 ms max.
OFF Response Time 0.8 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 8 (8 points/common, 1 circuit)
Internal Current
Consumption 100 mA max.
Fuse None
External Power
Supply 10.2 to 26.4 VDC, 20 mA min.
Weight 110 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
Internal circuits
to
Signal
name
Jxx_Ch1_Out00
Jxx_Ch1_Out07
+V
COM
12 to 24 VDC
Signal
name
Signal
name
Connec-
tor pin
*
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
B0
A0
L
L
L
L
L
L
L
L
Jxx_Ch1_Out01
Jxx_Ch1_Out03
Jxx_Ch1_Out05
Jxx_Ch1_Out07
Jxx_Ch1_Out00
Jxx_Ch1_Out02
Jxx_Ch1_Out04
Jxx_Ch1_Out06
NC
COM
+V
NC
NC
NC
NC
NC
NC
NC
11
CJ1W-OC/OA/OD
CJ1W-OD211 Transistor Output Unit (16 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Name 16-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model CJ1W-OD211
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 5.0 A/Unit
Maximum Inrush
Current 4.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.1 ms max.
OFF Response Time 0.8 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 16 (16 points/common, 1 circuit)
Internal Current
Consumption 5 VDC 100 mA max.
Fuse None
External Power
Supply 10.2 to 26.4 VDC, 20 mA min.
Weight 110 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
Internal circuits
to
Signal
name
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM
12 to 24 VDC
Signal
name
Signal
name
Connec-
tor pin *
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
B0
A0
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch1_Out01
Jxx_Ch1_Out03
Jxx_Ch1_Out05
Jxx_Ch1_Out07
Jxx_Ch1_Out09
Jxx_Ch1_Out11
Jxx_Ch1_Out13
Jxx_Ch1_Out15
Jxx_Ch1_Out00
Jxx_Ch1_Out02
Jxx_Ch1_Out04
Jxx_Ch1_Out06
Jxx_Ch1_Out08
Jxx_Ch1_Out10
Jxx_Ch1_Out12
Jxx_Ch1_Out14
COM
+V
CJ1W-OC/OA/OD
12
CJ1W-OD213 Transistor Output Unit (16 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Name 16-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model CJ1W-OD213
Rated Voltage 24 VDC
Operating Load
Voltage Range 20.4 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 5.0 A/Unit
Maximum Inrush
Current 4.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 15 μs max.
OFF Response Time 80 μs max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 16 (16 points/common, 1 circuit)
Internal Current
Consumption 5 VDC 150 mA max.
Fuse None
External Power
Supply 20.4 to 26.4 VDC, 55 mA min.
Weight 110 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
Internal circuits
to
Signal
name
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM
24 VDC
Signal
name
Signal
name
Connec-
tor pin
*
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
B0
A0
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch1_Out01
Jxx_Ch1_Out03
Jxx_Ch1_Out05
Jxx_Ch1_Out07
Jxx_Ch1_Out09
Jxx_Ch1_Out11
Jxx_Ch1_Out13
Jxx_Ch1_Out15
Jxx_Ch1_Out00
Jxx_Ch1_Out02
Jxx_Ch1_Out04
Jxx_Ch1_Out06
Jxx_Ch1_Out08
Jxx_Ch1_Out10
Jxx_Ch1_Out12
Jxx_Ch1_Out14
COM
+V
13
CJ1W-OC/OA/OD
CJ1W-OD231 Transistor Output Unit (32 Points)
Name 32-point Transistor Output Unit with Fujitsu Connector (Sinking Outputs)
Model CJ1W-OD231
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 2.0 A/common, 4.0 A/Unit
Maximum Inrush
Current 4.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.1 ms max.
OFF Response Time 0.8 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 32 (16 points/common, 2 circuits)
Internal Current
Consumption 5 VDC 140 mA max.
Fuse None
External Power
Supply 10.2 to 26.4 VDC, 30 mA min.
Weight 70 g max.
Accessories None
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•Be sure to wire both terminals A9 and A19 (COM0).
•Be sure to wire both terminals B9 and B19 (COM1).
•Be sure to wire both terminals A10 and A20 (+V).
•Be sure to wire both terminals B10 and B20 (+V).
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
to
to
Internal circuits
Wd m+1
Wd m
Allocated
CIO word
Signal
name
Connector
row A
Connector
row B
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM0
Jxx_Ch2_Out00
+V
Jxx_Ch2_Out15
COM1
COM0
COM1
SW
Wd m+1
Wd m+1
Wd m
Wd m
12 to
24 VDC 12 to
24 VDC
Signal
name
Signal
name
Connec-
tor pin Allocated
CIO word
Allocated
CIO word
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
+V
COM0
+V
COM0
Jxx_Ch1_Out08
Jxx_Ch1_Out09
Jxx_Ch1_Out10
Jxx_Ch1_Out11
Jxx_Ch1_Out12
Jxx_Ch1_Out13
Jxx_Ch1_Out14
Jxx_Ch1_Out15
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
COM1
+V
COM1
+V
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out10
Jxx_Ch2_Out11
Jxx_Ch2_Out12
Jxx_Ch2_Out13
Jxx_Ch2_Out14
Jxx_Ch2_Out15
Jxx_Ch2_Out00
Jxx_Ch2_Out01
Jxx_Ch2_Out02
Jxx_Ch2_Out03
Jxx_Ch2_Out04
Jxx_Ch2_Out05
Jxx_Ch2_Out06
Jxx_Ch2_Out07
CJ1W-OC/OA/OD
14
CJ1W-OD233 Transistor Output Unit (32 Points)
Name 32-point Transistor Output Unit with MIL Connector (Sinking Outputs)
Model CJ1W-OD233
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 2 A/common, 4 A/Unit
Maximum Inrush
Current 4.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.1 ms max.
OFF Response Time 0.8 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 32 (16 points/common, 2 circuits)
Internal Current
Consumption 140 mA max.
Fuse None
External Power
Supply 12 to 24 VDC, 30 mA min.
Weight 70 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•Be sure to wire both terminals 23 and 24 (COM0).
•Be sure to wire both terminals 3 and 4 (COM1).
•Be sure to wire both terminals 21 and 22 (+V).
•Be sure to wire both terminals 1 and 2 (+V).
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Wd m+1
Wd m
to
to
Output indicator
Internal circuits
Allocated
CIO word
Signal
name
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM0
Jxx_Ch2_Out00
+V
Jxx_Ch2_Out15
COM1
COM0
COM1
SW
Wd m+1
Wd m
Wd m+1
Wd m
12 to
24 VDC
12 to
24 VDC
Signal
name
Signal
name
Connec-
tor pin Allocated
CIO word
Allocated
CIO word
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch2_Out00
Jxx_Ch2_Out01
Jxx_Ch2_Out02
Jxx_Ch2_Out03
Jxx_Ch2_Out04
Jxx_Ch2_Out05
Jxx_Ch2_Out06
+V
COM1
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out10
Jxx_Ch2_Out11
Jxx_Ch2_Out12
Jxx_Ch2_Out07
Jxx_Ch2_Out13
Jxx_Ch2_Out14
Jxx_Ch2_Out15
+V
COM1
+V+V
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
Jxx_Ch1_Out08
Jxx_Ch1_Out09
Jxx_Ch1_Out10
Jxx_Ch1_Out11
Jxx_Ch1_Out12
Jxx_Ch1_Out13
Jxx_Ch1_Out14
Jxx_Ch1_Out15
COM0 COM0
15
CJ1W-OC/OA/OD
CJ1W-OD234 Transistor Output Unit (32 Points)
Name 32-point Transistor Output Unit with MIL Connector (Sinking Outputs)
Model CJ1W-OD234
Rated Voltage 24 VDC
Operating Load
Voltage Range 20.4 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 2 A/common, 4 A/Unit
Maximum Inrush
Current 4.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 15 μs max.
OFF Response Time 80 μs max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 32 (16 points/common, 2 circuits)
Internal Current
Consumption 220 mA max.
Fuse None
External Power
Supply 20.4 to 26.4 VDC, 110 mA min.
Weight 70 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•Be sure to wire both terminals 23 and 24 (COM0).
•Be sure to wire both terminals 3 and 4 (COM1).
•Be sure to wire both terminals 21 and 22 (+V).
•Be sure to wire both terminals 1 and 2 (+V).
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Wd m+1
Wd m
to
to
Output indicator
Internal circuits
Allocated
CIO word
Signal name
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM0
Jxx_Ch2_Out00
+V
Jxx_Ch2_Out15
COM1
COM0
COM1
SW
Wd m+1
Wd m
Wd m+1
Wd m
24 VDC
24 VDC
Signal
name Signal
name
Connec-
tor pin Allocated
CIO word
Allocated
CIO word
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch2_Out00
Jxx_Ch2_Out01
Jxx_Ch2_Out02
Jxx_Ch2_Out03
Jxx_Ch2_Out04
Jxx_Ch2_Out05
Jxx_Ch2_Out06
+V
COM1
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out10
Jxx_Ch2_Out11
Jxx_Ch2_Out12
Jxx_Ch2_Out07
Jxx_Ch2_Out13
Jxx_Ch2_Out14
Jxx_Ch2_Out15
+V
COM1
+V+V
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
Jxx_Ch1_Out08
Jxx_Ch1_Out09
Jxx_Ch1_Out10
Jxx_Ch1_Out11
Jxx_Ch1_Out12
Jxx_Ch1_Out13
Jxx_Ch1_Out14
Jxx_Ch1_Out15
COM0 COM0
CJ1W-OC/OA/OD
16
CJ1W-OD261 Transistor Output Unit (64 Points)
Name 64-point Transistor Output Unit with Fujitsu Connectors (Sinking Outputs)
Model CJ1W-OD261
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.3 A/point, 1.6 A/common, 6.4 A/Unit
Maximum Inrush
Current 3.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 64 (16 points/common, 4 circuits)
Internal Current
Consumption 5 VDC, 170 mA max.
Fuse None
External Power
Supply 10.2 to 26.4 VDC, 50 mA min.
Weight 110 g max.
Accessories None
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
to
to
to
to
Wd m
Wd m+1
Wd m+2
Wd m+3
Internal circuits
Allocated
CIO word
Signal name
Connector
row A
Connector
row B
Connector
row A
Connector
row B
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM0
Jxx_Ch3_Out00
+V
Jxx_Ch3_Out15
COM2
COM0
COM2
+V
Jxx_Ch2_Out00
Jxx_Ch2_Out15
COM1
COM1
+V
Jxx_Ch4_Out00
Jxx_Ch4_Out15
COM3
COM3
CN1
SW
CN2
CJ1W-OC/OA/OD
17
External connection
and terminal-device
variable diagram
CN1 CN2
•When wiring, pay careful attention to the polarity of the external
power supply. The load may operate incorrectly if the polarity is
reversed.
•Be sure to wire both terminals A9 and A19 (COM0) of CN1.
•Be sure to wire both terminals B9 and B19 (COM1) of CN1.
•Be sure to wire both terminals A10 and A20 (+V) of CN1.
•Be sure to wire both terminals B10 and B20 (+V) of CN1.
•The signal names of the terminals are the device variable
names.The device variable names are the names that use "Jxx" as
the device name.
•When wiring, pay careful attention to the polarity of the external
power supply. The load may operate incorrectly if the polarity is
reversed.
•Be sure to wire both terminals A9 and A19 (COM2) of CN2.
•Be sure to wire both terminals B9 and B19 (COM3) of CN2.
•Be sure to wire both terminals A10 and A20 (+V) of CN2.
•Be sure to wire both terminals B10 and B20 (+V) of CN2.
•The signal names of the terminals are the device variable
names.The device variable names are the names that use "Jxx" as
the device name.
12 to
24
VDC
Wd m
Wd m+1
12 to
24
VDC
Wd m+1
Wd m
Signal
name
Signal
name
Connec-
tor pin Allocated
CIO word
Allocated
CIO word
COM0
+V
COM0
+V
COM1
+V
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out10
Jxx_Ch2_Out11
Jxx_Ch2_Out12
Jxx_Ch2_Out13
Jxx_Ch2_Out14
Jxx_Ch2_Out15
COM1
+V
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch2_Out00
Jxx_Ch2_Out01
Jxx_Ch2_Out02
Jxx_Ch2_Out03
Jxx_Ch2_Out04
Jxx_Ch2_Out05
Jxx_Ch2_Out06
Jxx_Ch2_Out07
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
Jxx_Ch1_Out08
Jxx_Ch1_Out09
Jxx_Ch1_Out10
Jxx_Ch1_Out11
Jxx_Ch1_Out12
Jxx_Ch1_Out13
Jxx_Ch1_Out14
Jxx_Ch1_Out15
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
12 to
24
VDC
Wd m+3
Wd m+2
Wd m+2
Wd m+3
12 to
24
VDC
Signal
name
Signal
name
Connec-
tor pin Allocated
CIO word
Allocated
CIO word
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
COM3
+V
COM3
+V
COM2
+V
Jxx_Ch3_Out08
Jxx_Ch3_Out09
Jxx_Ch3_Out10
Jxx_Ch3_Out11
Jxx_Ch3_Out12
Jxx_Ch3_Out13
Jxx_Ch3_Out14
Jxx_Ch3_Out15
COM2
+V
Jxx_Ch3_Out00
Jxx_Ch3_Out01
Jxx_Ch3_Out02
Jxx_Ch3_Out03
Jxx_Ch3_Out04
Jxx_Ch3_Out05
Jxx_Ch3_Out06
Jxx_Ch3_Out07
Jxx_Ch4_Out00
Jxx_Ch4_Out01
Jxx_Ch4_Out02
Jxx_Ch4_Out03
Jxx_Ch4_Out04
Jxx_Ch4_Out05
Jxx_Ch4_Out06
Jxx_Ch4_Out07
Jxx_Ch4_Out08
Jxx_Ch4_Out09
Jxx_Ch4_Out10
Jxx_Ch4_Out11
Jxx_Ch4_Out12
Jxx_Ch4_Out13
Jxx_Ch4_Out14
Jxx_Ch4_Out15
CJ1W-OC/OA/OD
18
CJ1W-OD263 Transistor Output Unit (64 Points)
Name 64-point Transistor Output Unit with MIL Connectors (Sinking Outputs)
Model CJ1W-OD263
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.3 A/point, 1.6 A/common, 6.4 A/Unit
Maximum Inrush
Current 3.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 64 (16 points/common, 4 circuits)
Internal Current
Consumption 170 mA max.
Fuse None
External Power
Supply 12 to 24 VDC, 50 mA min.
Weight 110 g max.
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Internal circuits
Output indicator
to Wd m
Wd m+1
Wd m+2
Wd m+3
Allocated
CIO word
Signal
name
Jxx_Ch1_Out00
+V
Jxx_Ch1_Out15
COM0
Jxx_Ch3_Out00
+V
Jxx_Ch3_Out15
COM2
COM0
COM2
+V
Jxx_Ch2_Out00
Jxx_Ch2_Out15
COM1
COM1
+V
Jxx_Ch4_Out00
Jxx_Ch4_Out15
COM3
COM3
CN1
SW
CN2
to
to
to
CJ1W-OC/OA/OD
19
External connection
and terminal-device
variable diagram
CN1 CN2
•When wiring, pay careful attention to the polarity of the external
power supply. The load may operate incorrectly if the polarity is
reversed.
•Be sure to wire both terminals 23 and 24 (COM0) of CN1.
•Be sure to wire both terminals 3 and 4 (COM1) of CN1.
•Be sure to wire both terminals 21 and 22 (+V) of CN1.
•Be sure to wire both terminals 1 and 2 (+V) of CN1.
•The signal names of the terminals are the device variable
names.The device variable names are the names that use "Jxx" as
the device name.
•When wiring, pay careful attention to the polarity of the external
power supply. The load may operate incorrectly if the polarity is
reversed.
•Be sure to wire both terminals 23 and 24 (COM2) of CN2.
•Be sure to wire both terminals 3 and 4 (COM3) of CN2.
•Be sure to wire both terminals 21 and 22 (+V) of CN2.
•Be sure to wire both terminals 1 and 2 (+V) of CN2.
•The signal names of the terminals are the device variable
names.The device variable names are the names that use "Jxx" as
the device name.
Wd m
Wd m
Wd m+1
Wd m+1
12 to
24
VDC
12 to
24
VDC
Signal
name Signal
name
Connec-
tor pin
Allocated
CIO word
Allocated
CIO word
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
+V
Jxx_Ch1_Out15
Jxx_Ch1_Out14
Jxx_Ch1_Out13
Jxx_Ch1_Out12
Jxx_Ch1_Out11
+V
+V
COM1
Jxx_Ch1_Out10
COM1
+V
Jxx_Ch1_Out00
Jxx_Ch1_Out07
Jxx_Ch1_Out06
Jxx_Ch1_Out05
Jxx_Ch1_Out04
Jxx_Ch1_Out03
Jxx_Ch1_Out02
Jxx_Ch1_Out01
COM0
Jxx_Ch1_Out08
Jxx_Ch1_Out09
COM0
Jxx_Ch2_Out15
Jxx_Ch2_Out14
Jxx_Ch2_Out13
Jxx_Ch2_Out12
Jxx_Ch2_Out11
Jxx_Ch2_Out10
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out00
Jxx_Ch2_Out07
Jxx_Ch2_Out06
Jxx_Ch2_Out05
Jxx_Ch2_Out04
Jxx_Ch2_Out03
Jxx_Ch2_Out02
Jxx_Ch2_Out01
Wd m+3
Wd m+3
Wd m+2
Wd m+2
12 to
24
VDC
12 to
24
VDC
Signal
name
Signal
name
Connec-
tor pin Allocated
CIO word
Allocated
CIO word
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
+V
COM3
+V
COM3
+V +V
COM2 COM2
Jxx_Ch4_Out08
Jxx_Ch4_Out09
Jxx_Ch4_Out10
Jxx_Ch4_Out11
Jxx_Ch4_Out12
Jxx_Ch4_Out13
Jxx_Ch4_Out14
Jxx_Ch4_Out15
Jxx_Ch3_Out08
Jxx_Ch3_Out09
Jxx_Ch3_Out10
Jxx_Ch3_Out11
Jxx_Ch3_Out12
Jxx_Ch3_Out13
Jxx_Ch3_Out14
Jxx_Ch3_Out15
Jxx_Ch4_Out00
Jxx_Ch4_Out01
Jxx_Ch4_Out02
Jxx_Ch4_Out03
Jxx_Ch4_Out04
Jxx_Ch4_Out05
Jxx_Ch4_Out06
Jxx_Ch4_Out07
Jxx_Ch3_Out00
Jxx_Ch3_Out01
Jxx_Ch3_Out02
Jxx_Ch3_Out03
Jxx_Ch3_Out04
Jxx_Ch3_Out05
Jxx_Ch3_Out06
Jxx_Ch3_Out07
CJ1W-OC/OA/OD
20
CJ1W-OD202 Transistor Output Unit (8 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.
Name 8-point Transistor Output Unit with Terminal Block (Sourcing Outputs)
Model CJ1W-OD202
Rated Voltage 24 VDC
Operating Load
Voltage Range 20.4 to 26.4 VDC
Maximum Load
Current 2 A/point, 8 A/Unit
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Load Short-circuit
Protection
Detection current: 6 A min.
Automatic restart after error clearance.
Line Disconnection
Detection Detection current: 200 mA
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 8 (4 points/common, 2 circuits)
Internal Current
Consumption 110 mA max.
Fuse None
External Power
Supply 24 VDC, 50 mA min.
Weight 120 g max.
Circuit Configuration
•When overcurrent or line disconnection is detected, the ERR indicator will light, and the corresponding bit (two points per bit) in the Basic
I/O Unit Information Area (A050 to A069) will change to TRUE.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
COM0 (+V)
COM1 (+V)
to
to
Output indicator
ERR indicator
Internal circuits
Signal name
Jxx_Ch1_Out03
Jxx_Ch1_Out00
0 V
Jxx_Ch1_Out04
Jxx_Ch1_Out07
0 V
Short-circuit
protection
Short-circuit
protection
24 VDC
24 VDC
Signal
name
Signal
name
Connec-
tor pin
*
B0
B1
B2
B3
B4
B5
B6
B7
B8
A0
A1
A2
A3
A4
A5
A6
A7
A8
L
L
L
L
L
L
L
L
Jxx_Ch1_Out00
Jxx_Ch1_Out02
0 V
NC
NC
Jxx_Ch1_Out04
Jxx_Ch1_Out06
NC
Jxx_Ch1_Out01
Jxx_Ch1_Out03
COM0 (+V)
NC
NC
NC
Jxx_Ch1_Out05
Jxx_Ch1_Out07
0 V
COM1 (+V)
21
CJ1W-OC/OA/OD
CJ1W-OD204 Transistor Output Unit (8 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.
Name 8-point Transistor Output Unit with Terminal Block (Sourcing Outputs)
Model CJ1W-OD204
Rated Voltage 24 VDC
Operating Load
Voltage Range 20.4 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 4.0 A/Unit
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Load Short-circuit
Protection
Detection current: 0.7 to 2.5 A
Automatic restart after error clearance.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 8 (8 points/common, 1 circuit)
Internal Current
Consumption 5 VDC, 100 mA max.
Fuse None
External Power
Supply 20.4 to 26.4 VDC, 40 mA min.
Weight 120 g max.
Circuit Configuration
•When overcurrent is detected, the ERR indicator will light, and the corresponding bit in the Basic I/O Unit Information Area (A050 to A069)
will change to TRUE.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Output indicator
ERR indicator
Internal circuits
to
Signal name
COM (+V)
Jxx_Ch1_Out00
Jxx_Ch1_Out07
0 V
Short-circuit
protection
24 VDC
Signal
name
Signal
name
Connec-
tor pin
*
B1
Jxx_Ch1_Out01
B2
Jxx_Ch1_Out03
B3
Jxx_Ch1_Out05
B4
Jxx_Ch1_Out07
B5
B6
B7
B8
A1
Jxx_Ch1_Out00
A2
Jxx_Ch1_Out02
A3
Jxx_Ch1_Out04
A4
Jxx_Ch1_Out06
A5
NC
A6
A7
A8
0 V
B0
A0
COM (+V)
L
L
L
L
L
L
L
L
NC
NC
NC
NC
NC
NC
NC
CJ1W-OC/OA/OD
22
CJ1W-OD212 Transistor Output Unit (16 Points)
* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. They are not printed on
the Units.
Name 16-point Transistor Output Unit with Terminal Block (Sourcing Outputs)
Model CJ1W-OD212
Rated Voltage 24 VDC
Operating Load
Voltage Range 20.4 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 5.0 A/Unit
Maximum Inrush
Current 0.1 mA max.
Leakage Current 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Load Short-circuit
Protection
Detection current: 0.7 to 2.5 A
Automatic restart after error clearance.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 16 (16 points/common, 1 circuit)
Internal Current
Consumption 5 VDC, 100 mA max.
External Power
Supply 20.4 to 26.4 VDC, 40 mA min.
Weight 120 g max.
Circuit Configuration
•When overcurrent is detected, the ERR indicator will light, and the corresponding bit in the Basic I/O Unit Information Area (A050 to A069)
will change to TRUE.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Internal circuits
Output indicator
ERR indicator
to
Signal name
Jxx_Ch1_Out15
Jxx_Ch1_Out00
0 V
COM (+V)
Short-circuit
protection
24 VDC
Signal
name
Signal
name
Connector
pin *
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
B0
A0
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch1_Out01
Jxx_Ch1_Out03
Jxx_Ch1_Out05
Jxx_Ch1_Out07
Jxx_Ch1_Out09
Jxx_Ch1_Out11
Jxx_Ch1_Out13
Jxx_Ch1_Out15
Jxx_Ch1_Out00
Jxx_Ch1_Out02
Jxx_Ch1_Out04
Jxx_Ch1_Out06
Jxx_Ch1_Out08
Jxx_Ch1_Out10
Jxx_Ch1_Out12
Jxx_Ch1_Out14
0 V
COM (+V)
23
CJ1W-OC/OA/OD
CJ1W-OD232 Transistor Output Unit (32 Points)
Name 32-point Transistor Output Unit with MIL Connector (Sourcing Outputs)
Model CJ1W-OD232
Rated Voltage 24 VDC
Operating Load
Voltage Range 20.4 to 26.4 VDC
Maximum Load
Current 0.5 A/point, 2.0 A/common, 4.0 A/Unit
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Load Short-circuit
Protection
Detection current: 0.7 to 2.5 A
Automatic restart after error clearance.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 32 (16 points/common, 2 circuits)
Internal Current
Consumption 5 VDC 150 mA max.
External Power
Supply 20.4 to 26.4 VDC, 70 mA min.
Weight 80 g max.
Accessories None
Circuit Configuration
•When overcurrent is detected, the ERR indicator will light, and the corresponding bit (bit allocated for each common)in the Basic I/O Unit
Information Area (A050 to A069)will change to TRUE.
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Wd m
Wd m+1
to
to
Output indicator
Internal circuits
ERR indicator
Allocated
CIO word
Signal name
Jxx_Ch1_Out15
Jxx_Ch1_Out00
0 V
Jxx_Ch2_Out00
Jxx_Ch2_Out15
0 V
SW
COM0 (+V)
COM0 (+V)
COM1 (+V)
COM1 (+V)
Short-circuit
protection
Short-circuit
protection
24
CJ1W-OC/OA/OD
External connection
and terminal-device
variable diagram
•When wiring, pay careful attention to the polarity of the external power supply. The load may operate incorrectly if the polarity is reversed.
•Be sure to wire both terminals 21 and 22 (COM0 (+V)).
•Be sure to wire both terminals 1 and 2 (COM1 (+V)).
•Be sure to wire both terminals 3 and 4 (0 V).
•Be sure to wire both terminals 23 and 24 (0 V).
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Wd m+1
Wd m+1
Wd m
Wd m
24 VDC
24 VDC
Signal
name
Signal
name
Connec-
tor pin
Allocated
CIO word
Allocated
CIO word
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Jxx_Ch2_Out00
Jxx_Ch2_Out01
Jxx_Ch2_Out02
Jxx_Ch2_Out03
Jxx_Ch2_Out04
Jxx_Ch2_Out05
Jxx_Ch2_Out06
Jxx_Ch2_Out07
0 V
COM1 (+V)
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out10
Jxx_Ch2_Out11
Jxx_Ch2_Out12
Jxx_Ch2_Out13
Jxx_Ch2_Out14
Jxx_Ch2_Out15
0 V
COM1 (+V)
0 V
COM0 (+V)
0 V
COM0 (+V)
Jxx_Ch1_Out00
Jxx_Ch1_Out01
Jxx_Ch1_Out02
Jxx_Ch1_Out03
Jxx_Ch1_Out04
Jxx_Ch1_Out05
Jxx_Ch1_Out06
Jxx_Ch1_Out07
Jxx_Ch1_Out08
Jxx_Ch1_Out09
Jxx_Ch1_Out10
Jxx_Ch1_Out11
Jxx_Ch1_Out12
Jxx_Ch1_Out13
Jxx_Ch1_Out14
Jxx_Ch1_Out15
25
CJ1W-OC/OA/OD
CJ1W-OD262 Transistor Output Unit (64 Points)
Name 64-point Transistor Output Unit with MIL Connectors (Sourcing Outputs)
Model CJ1W-OD262
Rated Voltage 12 to 24 VDC
Operating Load
Voltage Range 10.2 to 26.4 VDC
Maximum Load
Current 0.3 A/point, 1.6 A/common, 6.4 A/Unit
Maximum Inrush
Current 3.0 A/point, 10 ms max.
Leakage Current 0.1 mA max.
Residual Voltage 1.5 V max.
ON Response Time 0.5 ms max.
OFF Response Time 1.0 ms max.
Insulation Resistance
20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength 1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of 10 mA max.
Number of Circuits 64 (16 points/common, 4 circuits)
Internal Current
Consumption 170 mA max. (5 VDC)
Fuse None
External Power
Supply 10.2 to 26.4 VDC, 50 mA min.
Weight 110 g max.
Accessories None
Circuit Configuration
•The signal names of the terminals are the device variable names.
The device variable names are the names that use "Jxx" as the device name.
Wd m
Wd m+1
Wd m+3
Wd m+2
Internal circuits
Indicator switch
Output indicator
to
to
to
to
Allocated
CIO word
Signal
name
Jxx_Ch1_Out15
0 V
Jxx_Ch1_Out00
COM0
COM0
0 V
0 V
COM1
0 V
COM1
Jxx_Ch2_Out15
Jxx_Ch2_Out00
COM2
COM2
Jxx_Ch3_Out15
Jxx_Ch3_Out00
Jxx_Ch4_Out15
Jxx_Ch4_Out00
COM3
COM3
CN1 (OUT)
CN2 (OUT)
CJ1W-OC/OA/OD
26
External connection
and terminal-device
variable diagram
CN1 CN2
•When wiring, pay careful attention to the polarity of the external
power supply. The load may operate incorrectly if the polarity is
reversed.
•Be sure to wire both terminals 21 and 22 (COM0 (+V)) of CN1.
•Be sure to wire both terminals 1 and 2 (COM1 (+V)) of CN1.
•Be sure to wire both terminals 23 and 24 (0 V) of CN1.
•Be sure to wire both terminals 3 and 4 (0 V) of CN1.
•The signal names of the terminals are the device variable
names.The device variable names are the names that use "Jxx" as
the device name.
•When wiring, pay careful attention to the polarity of the external
power supply. The load may operate incorrectly if the polarity is
reversed.
•Be sure to wire both terminals 21 and 22 (COM2 (+V)) of CN2.
•Be sure to wire both terminals 1 and 2 (COM3 (+V)) of CN2.
•Be sure to wire both terminals 23 and 24 (0 V) of CN2.
•Be sure to wire both terminals 3 and 4 (0 V) of CN2.
•The signal names of the terminals are the device variable
names.The device variable names are the names that use "Jxx" as
the device name.
Wd m
12 to
24 VDC
Wd m+1
Wd m
Wd m+1
12 to
24 VDC
Signal
name
Signal
name
Connec-
tor pin
Allocated
CIO word
Allocated
CIO word
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
L L
Jxx_Ch2_Out15
Jxx_Ch2_Out14
Jxx_Ch2_Out13
Jxx_Ch2_Out12
Jxx_Ch2_Out11
Jxx_Ch2_Out10Jxx_Ch2_Out02
Jxx_Ch1_Out15
Jxx_Ch1_Out14
Jxx_Ch1_Out13
Jxx_Ch1_Out12
Jxx_Ch1_Out11
0 V
0 V
Jxx_Ch2_Out07
Jxx_Ch2_Out06
Jxx_Ch2_Out05
Jxx_Ch2_Out04
Jxx_Ch2_Out03
COM1 (+V)
Jxx_Ch1_Out10
0 V
Jxx_Ch1_Out00
Jxx_Ch1_Out07
Jxx_Ch1_Out06
Jxx_Ch1_Out05
Jxx_Ch1_Out04
Jxx_Ch1_Out03
Jxx_Ch1_Out02
Jxx_Ch1_Out01
COM0 (+V)
Jxx_Ch1_Out08
Jxx_Ch1_Out09
COM0 (+V)
Jxx_Ch2_Out08
Jxx_Ch2_Out09
Jxx_Ch2_Out00
Jxx_Ch2_Out01
0 V
COM1 (+V)
Wd m+3
Wd m+2
12 to
24 VDC
12 to
24 VDC
Wd m+3
Wd m+2
Signal
name
Signal
name
Connector
pin Allocated
CIO word
Allocated
CIO word
LL
LL
LL
L L
LL
L L
L L
LL
L L
L L
L L
LL
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
39
37
35
33
31
29
27
25
23
21
19
17
15
13
10
9
7
5
3
1
L
L
LL
L
LL
L
Jxx_Ch3_Out00
Jxx_Ch3_Out01
Jxx_Ch3_Out02
Jxx_Ch3_Out03
Jxx_Ch3_Out04
Jxx_Ch3_Out05
Jxx_Ch3_Out06
Jxx_Ch3_Out07Jxx_Ch3_Out15
Jxx_Ch4_Out00
Jxx_Ch4_Out01
Jxx_Ch4_Out02
Jxx_Ch4_Out03
Jxx_Ch4_Out04
Jxx_Ch4_Out05
Jxx_Ch4_Out06
Jxx_Ch3_Out08
Jxx_Ch3_Out09
Jxx_Ch3_Out10
Jxx_Ch3_Out11
Jxx_Ch3_Out12
Jxx_Ch3_Out13
Jxx_Ch3_Out14
Jxx_Ch4_Out08
Jxx_Ch4_Out09
Jxx_Ch4_Out10
Jxx_Ch4_Out11
Jxx_Ch4_Out12
Jxx_Ch4_Out07
Jxx_Ch4_Out13
Jxx_Ch4_Out14
Jxx_Ch4_Out15
0 V
COM3 (+V)
0 V
COM2 (+V)
0 V
COM3 (+V)
0 V
COM2 (+V)
27
CJ1W-OC/OA/OD
Bit Allocations for Output Unit
8-point Output Unit 16-point Output Unit
32-point Output Unit 64-point Output Unit
Allocated CIO word Signal name(CJ/NJ)
CIO Bit
Wd m
(Output)
00 OUT0/Jxx_Ch1_Out00
01 OUT1/Jxx_Ch1_Out01
::
06 OUT6/Jxx_Ch1_Out06
07 OUT7/Jxx_Ch1_Out07
08 −
09 −
::
14 −
15 −
Allocated CIO word Signal name(CJ/NJ)
CIO Bit
Wd m
(Output)
00 OUT0/Jxx_Ch1_Out00
01 OUT1/Jxx_Ch1_Out01
::
14 OUT14/Jxx_Ch1_Out14
15 OUT15/Jxx_Ch1_Out15
Allocated CIO word Signal name(CJ/NJ)
CIO Bit
Wd m
(Output)
00 OUT0/Jxx_Ch1_Out00
01 OUT1/Jxx_Ch1_Out01
::
14 OUT14/Jxx_Ch1_Out14
15 OUT15/Jxx_Ch1_Out15
Wd m+1
(Output)
00 OUT0/Jxx_Ch2_Out00
01 OUT1/Jxx_Ch2_Out01
::
14 OUT14/Jxx_Ch2_Out14
15 OUT15/Jxx_Ch2_Out15
Allocated CIO word Signal name(CJ/NJ)
CIO Bit
Wd m
(Output)
00 OUT0/Jxx_Ch1_Out00
01 OUT1/Jxx_Ch1_Out01
::
14 OUT14/Jxx_Ch1_Out14
15 OUT15/Jxx_Ch1_Out15
Wd m+1
(Output)
00 OUT0/Jxx_Ch2_Out00
01 OUT1/Jxx_Ch2_Out01
::
14 OUT14/Jxx_Ch2_Out14
15 OUT15/Jxx_Ch2_Out15
Wd m+2
(Output)
00 OUT0/Jxx_Ch3_Out00
01 OUT1/Jxx_Ch3_Out01
::
14 OUT14/Jxx_Ch3_Out14
15 OUT15/Jxx_Ch3_Out15
Wd m+3
(Output)
00 OUT0/Jxx_Ch4_Out00
01 OUT1/Jxx_Ch4_Out01
::
14 OUT14/Jxx_Ch4_Out14
15 OUT15/Jxx_Ch4_Out15
CJ1W-OC/OA/OD
28
External Interface
8-point/16-point Units (18-point Terminal Blocks)
Note: The CJ1W-OD202, CJ1W-OD204, and CJ1W-OD212 also have an ERR indicator for the load short-circuit alarm.
32-point Units (Models with 40-point Fujitsu Connector or MIL Connector)
Note: Only the CJ1W-OD232 has an ERR indicator for the load short-circuit alarm.
ERR
0 1 2 3 4 5 6 7
8 9 10 11 12 13 14 15
Connector
Connect to the connector on the next Unit.
I/O indicators
Model number label
Terminal block for
I/O wiring, 18P × 1
ID231
ID232
0 1 2 3
4 5 6 7
8 9
12 13 14 15
10 11
ERR
1 2
Wd m (Row A on connector)
Fujitsu connector MIL connector
Bottom of connector
Top of connector
Wd m+1 (Row B on connector)
Setting 1
Setting 2
Model number
I/O indicators
Unit with MIL Connector
Unit with Fujitsu-compatible
Connector
Connector
Connected to the connector on the next Unit.
Indicator Switch
Changes the 16 I/O displayed on the I/O indicators.
Word m
or
m+1
I/O wiring
connector
(40-pin × 1)
29
CJ1W-OC/OA/OD
64-point Units (Models with Two 40-point Fujitsu Connectors or MIL Connector)
Wiring Basic I/O Units with Terminal Blocks
Electric Wires
The following wire gauges are recommended.
Crimp terminals
Use crimp terminals (M3) having the dimensions shown below.
Terminal Block Connector Wire Size
18-terminal AWG 22 to 18 (0.32 to 0.82 mm2)
ID261
0 1 2 3 4 5 6 7
8 9 12 13 14 15
10 11
0 1 2 3 4 5 6 7
8 9 12 13 14 15
10 11
I
II
ID261
1 2
Model number
I/O indicators
Unit with MIL Connector
Unit with Fujitsu-compatible
Connector
Connector
Connected to the connector on the next Unit.
Indicator Switch
Changes the 32 I/O displayed on the I/O indicators.
Setting 1
Setting 2
I/O wiring
connector
(40-pin × 2)
Wd m and m+1: CN1
Wd m+2 and m+3: CN2
Word m or
m+2
Word m+1
or m+3
6.2 mm max. 6.2 mm max.
CJ1W-OC/OA/OD
30
I/O Unit Wiring Methods
An I/O Unit can be connected to an external device by any of the following three methods.
1. User-provided Cable
An I/O Unit can be directly connected to an external device by using a connector.
2. Connector-Terminal Block Conversion Unit
Use a Connecting Cable to connect to a Connector-Terminal Block Conversion Unit.
Converting the I/O Unit connector to a screw terminal block makes it easy to connect external devices.
3. I/O Relay Terminal
Use a Connecting Cable to connect to an I/O Relay Terminal.
The I/O specifications can be converted to relay outputs and AC inputs by connecting the I/O Relay Terminal to an I/O Unit.
B
C
A
AUser-provided cable
BExternal device
CConnector
B
C
A
AConnecting Cable for Connector-Terminal Block Conversion Unit
XW2Z
BConnector-Terminal Block Conversion Unit
XW2R
CConversion to a screw terminal block
B
B
A
AG79 I/O Relay Terminal Connecting Cable
BG7@@ I/O Relay Terminals
Or, conversion to relay outputs and AC inputs.
31
CJ1W-OC/OA/OD
1. Using User-made Cables with Connector
Available Connectors
Use the following connectors when assembling a connector and cable.
32- and 64-point Basic I/O Units with Fujitsu-compatible Connectors
Applicable Units
Applicable Cable-side Connectors
32- and 64-point Basic I/O Units with MIL Connectors
Applicable Units
Applicable Cable-side Connectors
*1. Socket and Stain Relief set.
*2. Crimp Contacts (XG5W-0232) are sold separately.
*3. Applicable wire size is AWG 28 to 24. For applicable conductor construction and more information, visit the OMRON website at
www.ia.omron.com.
Wire Size
We recommend using cable with wire gauges of AWG 28 to 24 (0.08 to 0.2 mm2). Use cable with external wire diameters of 1.61 mm max.
Crimping Tools
The following models are recommended for crimping tools and pressure-welding tools for Fujitsu connectors.
Tools for Crimped Connectors (Fujitsu Component)
Tools for Pressure-welded Connectors (Fujitsu Component)
The following models are recommended for tools for OMRON MIL connectors.
Tools for Pressure-welded Connectors (OMRON)
Tools for Crimped Connectors (OMRON)
Model Specifications Pins
CJ1W-OD231 Transistor Output Unit with Sinking Outputs, 32 outputs 40
CJ1W-OD261 Transistor Output Unit with Sinking Outputs, 64 outputs
Connection Pins OMRON set Fujitsu parts
Solder-type 40 C500-CE404 Socket: FCN-361J040-AU
Connector cover: FCN-360C040-J2
Crimped 40 C500-CE405
Socket: FCN-363J040
Connector cover: FCN-360C040-J2
Contacts: FCN-363J-AU
Pressure-welded 40 C500-CE403 FCN-367J040-AU/F
Model Specifications Pins
CJ1W-OD232 Transistor Output Unit with sourcing outputs, 32 outputs
40
CJ1W-OD262 Transistor Output Unit with sourcing outputs, 64 outputs
CJ1W-OD233
CJ1W-OD234 Transistor Output Unit with sinking outputs, 32 outputs
CJ1W-OD263 Transistor Output Unit with sinking outputs, 64 outputs
Connection Pins OMRON set DDK parts
Pressure-welded 40 XG4M-4030-T *1 FRC5-A040-3T0S
Crimped
40 XG5N-401 *2 HU-40OS2-001
−
Crimp Contacts for XG5N *3
XG5W-0232 (loose contacts: 100 pieces)
XG5W-0232-R (reel contacts: 10,000 pieces)
HU-111S
Product Name Model
Hand Crimping Tool FCN-363T-T005/H
Contact Withdrawal Tool FCN-360T-T001/H
Product Name Model
Hand Press FCN-707T-T101/H
Cable Cutter FCN-707T-T001/H
Locator Plate FCN-367T-T012/H
Product Name Model
Pressure-welding Tool XY2B-0002
Attachment XY2B-1007
Product Name Model
Manual Crimping Tool XY2B-7007
CJ1W-OC/OA/OD
32
2. Connecting Connector-Terminal Block Conversion Units
Connection Patterns for Connector-Terminal Block Conversion Units
Combination of I/O Units with Connector-Terminal Block Conversion Units
Pattern Configuration Number of Connectors
A 1
B 2
Unit I/O
capacity
Number of
connectors Polarity Connection
pattern
Connecting
Cable
Connector-Terminal
Block
Conversion Unit
Wiring method Common
terminals
CJ1W-
OD231 32 outputs 1 Fujitsu
connector NPN A XW2Z-@@@B
XW2R-J34G-C3 Phillips screw
NoXW2R-E34G-C3 Slotted screw (rise up)
XW2R-P34G-C3 Push-in spring
CJ1W-
OD232 32 outputs 1 MIL
connector PNP A XW2Z-@@@K
XW2R-J34G-C4 Phillips screw
NoXW2R-E34G-C4 Slotted screw (rise up)
XW2R-P34G-C4 Push-in spring
CJ1W-
OD233 32 outputs 1 MIL
connector NPN A XW2Z-@@@K
XW2R-J34G-C4 Phillips screw
NoXW2R-E34G-C4 Slotted screw (rise up)
XW2R-P34G-C4 Push-in spring
CJ1W-
OD234 32 outputs 1 MIL
connector NPN A XW2Z-@@@K
XW2R-J34G-C4 Phillips screw
NoXW2R-E34G-C4 Slotted screw (rise up)
XW2R-P34G-C4 Push-in spring
CJ1W-
OD261 64 outputs 2 Fujitsu
connectors NPN B XW2Z-@@@B
(2 Cables)
XW2R-J34G-C3 (2 Units) Phillips screw
NoXW2R-E34G-C3 (2 Units) Slotted screw (rise up)
XW2R-P34G-C3 (2 Units) Push-in spring
CJ1W-
OD262 64 outputs 2 MIL
connectors PNP B XW2Z-@@@K
(2 Cables)
XW2R-J34G-C4 (2 Units) Phillips screw
NoXW2R-E34G-C4 (2 Units) Slotted screw (rise up)
XW2R-P34G-C4 (2 Units) Push-in spring
CJ1W-
OD263 64 outputs 2 MIL
connectors NPN B XW2Z-@@@K
(2 Cables)
XW2R-J34G-C4 (2 Units) Phillips screw
NoXW2R-E34G-C4 (2 Units) Slotted screw (rise up)
XW2R-P34G-C4 (2 Units) Push-in spring
Connecting Cable
34 terminals
Connector-Terminal
Block Conversion Unit
Connecting Cable
34 terminals 34 terminals
Connector-Terminal
Block Conversion Unit
33
CJ1W-OC/OA/OD
Types of Connecting Cables
3. Connecting I/O Relay Terminals
Connection Patterns for I/O Relay Terminals
Combination of I/O Units with I/O Relay Terminal and Connecting Cables
Appearance Connectors Model Cable lenght [m]
XW2Z-@@@B
One 40-pin Connector Made by Fujitsu Component, Ltd.
to One 40-pin MIL Connector
XW2Z-050B 0.5
XW2Z-100B 1
XW2Z-150B 1.5
XW2Z-200B 2
XW2Z-300B 3
XW2Z-500B 5
XW2Z-@@@K
One 40-pin MIL Connector to One 40-pin MIL Connector
XW2Z-C50K 0.5
XW2Z-100K 1
XW2Z-150K 1.5
XW2Z-200K 2
XW2Z-300K 3
XW2Z-500K 5
Pattern Configuration
A
B
Unit I/O capacity Number of
connectors Polarity Connection
pattern
Number of
branches Connecting Cable I/O Relay Terminal
CJ1W-OD231 32 outputs 1 Fujitsu connector NPN
A 2 G79-O@C-@G7TC-OC16
A 2 G79-O@C-@G7TC-OC08
A 2 G79-O@C-@G70D-SOC16
A 2 G79-O@C-@G70D-FOM16
A 2 G79-O@C-@G70D-VSOC16
A 2 G79-O@C-@G70D-VFOM16
A 2 G79-O@C-@G70A-ZOC16-3 and Relay
A 2 G79-O@C-@G70R-SOC08
A 2 G79-O@C-@G70D-SOC08
CJ1W-OD232 32 outputs 1 MIL connector PNP
A 2 G79-I@-@-D1 G7TC-OC16-1
A 2 G79-O@-@-D1 G70D-SOC16-1
A 2 G79-O@-@-D1 G70D-FOM16-1
A 2 G79-O@-@-D1 G70A-ZOC16-4 and Relay
Connecting Cable
I/O Relay Terminal
Connecting Cable
I/O Relay Terminal I/O Relay Terminal
CJ1W-OC/OA/OD
34
Types of Connecting Cables
CJ1W-OD233 32 outputs 1 MIL connector NPN
A 2 G79-O@-@-D1 G7TC-OC16
A 2 G79-O@-@-D1 G7TC-OC08
A 2 G79-O@-@-D1 G70D-SOC16
A 2 G79-O@-@-D1 G70D-FOM16
A 2 G79-O@-@-D1 G70D-VSOC16
A 2 G79-O@-@-D1 G70D-VFOM16
A 2 G79-O@-@-D1 G70A-ZOC16-3 and Relay
A 2 G79-O@-@-D1 G70R-SOC08
A 2 G79-O@-@-D1 G70D-SOC08
CJ1W-OD234 32 outputs 1 MIL connector NPN
A 2 G79-O@-@-D1 G7TC-OC16
A 2 G79-O@-@-D1 G7TC-OC08
A 2 G79-O@-@-D1 G70D-SOC16
A 2 G79-O@-@-D1 G70D-FOM16
A 2 G79-O@-@-D1 G70D-VSOC16
A 2 G79-O@-@-D1 G70D-VFOM16
A 2 G79-O@-@-D1 G70A-ZOC16-3 and Relay
A 2 G79-O@-@-D1 G70R-SOC08
A 2 G79-O@-@-D1 G70D-SOC08
CJ1W-OD261 64 outputs 2 Fujitsu connectors NPN
B 2 G79-O@C-@G7TC-OC16
B 2 G79-O@C-@G7TC-OC08
B 2 G79-O@C-@G70D-SOC16
B 2 G79-O@C-@G70D-FOM16
B 2 G79-O@C-@G70D-VSOC16
B 2 G79-O@C-@G70D-VFOM16
B 2 G79-O@C-@G70A-ZOC16-3 and Relay
B 2 G79-O@C-@G70R-SOC08
B 2 G79-O@C-@G70D-SOC08
CJ1W-OD262 64 outputs 2 MIL connectors PNP
B 2 G79-I@-@-D1 G7TC-OC16-1
B 2 G79-O@-@-D1 G70D-SOC16-1
B 2 G79-O@-@-D1 G70D-FOM16-1
B 2 G79-O@-@-D1 G70A-ZOC16-4 and Relay
CJ1W-OD263 64 outputs 2 MIL connectors NPN
B 2 G79-O@-@-D1 G7TC-OC16
B 2 G79-O@-@-D1 G7TC-OC08
B 2 G79-O@-@-D1 G70D-SOC16
B 2 G79-O@-@-D1 G70D-FOM16
B 2 G79-O@-@-D1 G70D-VSOC16
B 2 G79-O@-@-D1 G70D-VFOM16
B 2 G79-O@-@-D1 G70A-ZOC16-3 and Relay
B 2 G79-O@-@-D1 G70R-SOC08
B 2 G79-O@-@-D1 G70D-SOC08
Cable length G79-O@C-@G79-O@-@-D1 G79-I@-@-D1
0.25m −−−
0.5m −G79-O50-25-D1 G79-I50-25-D1
1.0m G79-O100C-75 G79-O75-50-D1 G79-I75-50-D1
1.5m G79-O150C-125 −−
2.0m G79-O200C-175 −−
3.0m G79-O300C-275 −−
5.0m G79-O500C-475 −−
Unit I/O capacity Number of
connectors Polarity Connection
pattern
Number of
branches Connecting Cable I/O Relay Terminal
35
CJ1W-OC/OA/OD
Dimensions (Unit: mm)
8-point/16-point Units (18-point Terminal Blocks)
CJ1W-OC201/ OC211/ OA201/ OD201 / OD202/ OD203/ OD204/ OD211/ OD213 / OD212
32-point Unit (Output Units)
With Fujitsu-Compatible Connector (40-pin × 1)
CJ1W-OD231
With MIL Connector (40-pin × 1)
CJ1W-OD232 / OD233 / OD234
ID211
01 23 4 56 7
89
10 11 12 13 14 15
0
1
3
2
4
5
7
6
8
9
11
10
12
13
14
15
DC24V
7mA
COM
COM
2.7
2.7 90
65
89
31
ID231
0
0
1
20
AB
20
1
1
123
456 7
89
10 11
12 13 14 15
DC24V 4.1mA
2.72.7 90
65
66.5
(112.5)
20
ID231
0
01
1ch
0ch
123
456 7
89
10 11
12 13 14 15
DC24V 4.1mA
65
83.6
2.72.7 90
20
CJ1W-OC/OA/OD
36
64-point Units (Output Units)
With Fujitsu-Compatible Connector (40-pin × 2)
CJ1W-OD261
With MIL Connector (40-pin × 2)
CJ1W-OD262 / OD263
Related Manuals
Name Cat. No. Contents
CJ-series CJ2 CPU Unit Hardware User's Manual
CJ2H-CPU6@-EIP
CJ2H-CPU6@
CJ2M-CPU@@
W472
Describes the following for CJ2 CPU Units:
•Overview and features
•Basic system configuration
•Part nomenclature and functions
•Mounting and setting procedure
•Remedies for errors
•Also refer to the Software User’s Manual (W473).
CJ Series
CJ1H-CPU@@H-R, CJ1G/H-CPU@@H, CJ1G-CPU@@P,
CJ1G-CPU@@, CJ1M-CPU@@
Programmable Controllers Operation Manual
W393 Provides an outlines of and describes the design, installation, maintenance, and other
basic operations for the CJ-series PLCs.
NJ-series
CPU Unit Hardware User's Manual
NJ501-@@@@ W500
An introduction to the entire NJ-series system is provided along with the following
information on a Controller built with an NJ501 CPU Unit.
•Features and system configuration
•Introduction
•Part names and functions
•General specifications
•Installation and wiring
•Maintenance and inspection
Use this manual together with the NJ-series CPU Unit Software User's Manual (Cat. No.
W501).
65
66.5
(112.5)
31
90 2.72.7
83.6
65
90 2.72.7
31
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2014.9
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2014 All Right Reserved.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Omron:
G7TC-OC08 DC24V G70D-VSOC16 DC24 G70D-SOC16-1 DC24 G70D-VFOM16 DC24 G7TC-OC16 DC12V
G7TC-OC08-1 DC24V G7TC-ID16 DC24V G7TC-OC16 DC24V G70D-FOM16 G70D-ET G7TC-OC08 DC12V
G70D-SOC16 DC24 G7TC-ID16-5 DC24 CJ1W-OD234 CJ1W-OD213
