2N7000D74Z - ON SEMICONDUCTOR - Datasheet.Support

To learn more about ON Semiconductor, please visit our website at

www.onsemi.com

Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers

will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor

product management systems do not have the ability to manage part nomenclature that utilizes an underscore

(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain

device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated

device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please

email any questions regarding the system integration to Fairchild_questions@onsemi.com.

Is Now Part of

ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number

of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right

to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and speciﬁcally disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON

Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON

Semiconductor data sheets and/or speciﬁcations can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s

technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA

Class 3 medical devices or medical devices with a same or similar classiﬁcation in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended

or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its ofﬁcers, employees, subsidiaries, afﬁliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out

of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor

is an Equal Opportunity/Afﬁrmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

September 2009

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

FIN1215 / FIN1216 / FIN1217/ FIN1218

LVDS 21-Bit Serializers / De-Serializers

Features

 Low Power Consumption

 20MHz to 85MHz Shift Clock Support

 50% Duty Cycle on the Clock Output of Receiver

 ±1V Common-mode Range ~1.2V

 Narrow Bus Reduces Cable Size and Cost

 High Throughput: 1.785Gbps

 Up to 595Mbps per Channel

 Internal PLL with No External Components

 Compatible with TIA/EIA-644 Specification

 Offered in 48-lead TSSOP Packages

Description

The FIN1217 and FIN1215 transform 21-bit wide

parallel LVTTL (Low-Voltage TTL) data into three serial

LVDS (Low-Voltage Differential Signaling) data

streams. A phase-locked transmit clock is transmitted in

parallel with the data stream over a separate LVDS link.

Every cycle of transmit clock, 21 bits of input LVTTL

data are sampled and transmitted.

The FIN1216 and FIN1218 receives and converts the

three serial LVDS data streams back into 21 bits of

LVTTL data. Table 1 provides a matrix summary of the

serializers and de-serializers available. For the

FIN1217, at a transmit clock frequency of 85MHz, 21

bits of LVTTL data are transmitted at a rate of 595Mbps

per LVDS channel.

These chipsets solve EMI and cable size problems

associated with wide and high-speed TTL interfaces.

Ordering Information

Part Number Operating

Temperature

Range

Eco

Status Package Packing

Method

FIN1215MTDX

-40 to + 85°C RoHS 48-Lead Thin Shrink Small Outline Package (TSSOP) Tape and Reel

FIN1216MTDX

FIN1217MTDX

FIN1218MTDX

(Preliminary)

For Fairchild’s defini t i on of Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 2

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Block Diagrams

Figure 1. FIN1217 / FIN1215 Transmitter Functional Diagram

Figure 2. FIN1218 / FIN1216 Receiver Functional Diagram

Table 1. Serializers / De-Serializers Chip Matrix

Part CLK

Frequency LVTTL IN LVDS OUT LVDS IN LVTTL

OUT Package

FIN1215 66 21 3 48-Lead TSSOP

FIN1216 66 3 21 48-Lead TSSOP

FIN1217 85 21 3 48-Lead TSSOP

FIN1218 85 3 21 48-Lead TSSOP

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 3

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Transmitters

Pin Configurat ion

Figure 3. FIN1217 / FIN1215 (21:3 Transmitter)

Pin Definitions

Pin Names I/O

Type # of

Pins Description of Signals

TxIn I 21 LVTTL Level Inputs

TxCKLIn I 1 LVTTL Level Clock Input; the rising edge is for data strobe

TxOut+ O 3 Positive LVDS Differential Data Output

TxOut O 3 Negative LVDS Differential Data Output

TxCLKOut+ O 1 Positive LVDS Differential Clock Output

TxCLKOut- O 1 Negative LVDS Differential Clock Output

/PwrDn I 1

LVTTL Level Power-Down Input; assertion (LOW) puts the outputs in high-

impedance state

PLL VCC I 1 Power Supply Pin for LVDS Outputs

PLL GND I 2 Ground Pins for PLL

LVDS VCC I 1 Power Supply Pins for LVDS Outputs

LVDS GND I 3 Ground Pin for LVDS Outputs

VCC I 4 Power Supply Pins for LVTTL Inputs

GND I 5 Ground Pins for LVTTL Inputs

NC No Connect

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 4

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Receivers

Pin Configurat ion

Figure 4. FIN1216 / FIN1218 (3:21 Receiver)

Pin Definitions

Pin Names I/O

Type # of

Pins Description of Signals

RxIn I 3 Negative LVDS Differential Data Output

RxIn+ I 3 Positive LVDS Differential Data Output

RxCLKIn- I 1 Negative LVDS Differential Clock Output

RxCLKIn+ I 1 Positive LVDS Differential Clock Output

RxOut- O 21 LVTTL Level Data Outputs Goes HIGH for /PwrDn LOW

RxCLKOut O 1 LVTTL Level Clock Ou tput

/PwrDn I 1

LVTTL Level Input; Refer to Transmitter and Receiver Power-up and Power-down

Operation Truth Table

PLL VCC I 1 Power Supply Pin for PLL

PLL GND I 2 Ground Pins for PLL

LVDS VCC I 1 Power Supply Pins for LVDS Inputs

LVDS GND I 3 Ground Pin for LVDS Inputs

VCC I 4 Power Supply Pins for LVTTL Outputs

GND I 5 Ground Pins for LVTTL Outputs

NC No Connect

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 5

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Truth Tables

Transmitter

Inputs Outputs

TxIn TxCLKIn PwrDn(1) TxOut± TxCLKOut±

Active Active HIGH LOW / HIGH LOW / HIGH

Active LOW / HIGH

High Impedance HIGH LOW / HIGH Don’t Care(2)

Floating Active HIGH LOW LOW / HIGH

Floating Floating HIGH LOW Don’t Care(2)

Don’t Care Don’t Care LOW High Impedance High Impedance

Notes:

1. The outputs of the transmitter or receiver remain in a high-impedance state until VCC reaches 2V.

2. TxCLKOut± settles at a free running frequency when the part is powered up, PwrDn is HIGH and the TxCLKIn is

a steady logic level LOW / HIGH / high-impedance.

Receiver

Inputs Outputs

RxIn± RxCLKIn± /PwrDn(3) RxOut RxCLKOut

Active Active HIGH LOW / HIGH LOW / HIGH

Active Failsafe Condition(4) HIGH Last Valid State HIGH

Failsafe Condition(4) Active HIGH HIGH LOW / HIGH

Failsafe Condition(4) Failsafe Condition(4) HIGH Last Valid State(5) HIGH

Don’t Care Don’t Care LOW LOW HIGH

Notes:

3. The outputs of the transmitter or receiver remain in a high-impedance state until VCC reaches 2V.

4. Failsafe condition is defined as the input being terminated and un-driven, shorted, or open.

5. If RxCLKIn± is removed prior to the RxIn± date being removed, RxOut is the last valid state. If RxIn± data is

removed prior to RxCLKIn± being removed, RxOut is HIGH.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 6

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Absolute Maximum Ratings

Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be

operable above the recommended operating conditions and stressing the parts to these levels is not recommended.

In addition, extended exposure to stresses above the recommended operating conditions may affect device

reliability. The absolute maximum ratings are stress ratings only.

Symbol Parameter Min. Max. Unit

VCC Power Supply Voltage -0.3 +4.6 V

VTTL TTL/CMOS Input/Output Voltage -0.5 +4.6 V

VLVDS LVDS Input/Output Voltage -0.3 +4.6 V

IOSD LVDS Output Short-Circuit Current Continuous

TSTG Storage Temperature Range -65 +150 °C

TJ Maximum Junction Temperature, Soldering 4 seconds +150 °C

TL Lead Temperature +260 °C

ESD

Human Body Model,

JESD22-A114

(1.5kΩ, 100pF)

LVDS I/O to Ground 10.0 kV

All Pins (FIN1215, FIN1217) 6.5

Machine Model,

JESD22-A115, 0Ω, 200pF FIN1215, FIN1217 Only >400 V

Recommended Operating Conditions

The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended

operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not

recommend exceeding them or designing to Absolute Maximum Ratings.

Symbol Parameter Min. Max. Unit

VCC Supply Voltage 3.0 3.6 V

TA Operating Temperature -40 +85 °C

VCCNPP Maximum Supply Noise Voltage(6) 100 mVPP

Note:

6. 100mV VCC noise should be tested for frequency at least up to 2MHz. All the specifications should be met under

such a noise level.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 7

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Transmitter DC Electrical Characteristics

Typical values are at TA=25°C and with VCC=3.3V; minimum and maximum are at over supply voltages and operating

temperatures ranges, unless otherwise specified.

Symbol Parameter Test Conditions Min. Typ. Max. Units

Transmitter LVTTL Input Characteristics

VIH Input High Voltage 2.0 VCC V

VIL Input Low Voltage GND 0.8 V

VIK Input Clamp Voltage IIK=-18mA -0.79 -1.50 V

IIN Input Current VIN=0.4V to 4.6V 1.8 10.0 μA

VIN=GND -10.0 0

Transmitter LVDS Output Characteristics(7)

VOD Output Differential Voltage

RL=100Ω, Figure 4

250 450 mV

ΔVOD VOD Magnitude Change from

Differential LOW-to-HIGH 35 mV

VOS Offset Voltage 1.125 1.250 1.375 V

ΔVOS Offset Magnitude Change from

Differential LOW-to-HIGH 25 mV

IOS Short-Circuit Output Current VOUT=0V -3.5 -5.0 mA

IOZ Disabled Output Leakage Current DO=0V to 4.6V,

/PwrDn=0V ±1.0 ±10.0

μA

Transmitter Supply Current

ICCWT 21:3 Transmitter Power Supply Current

for Worst-Case Pattern with Load(8, 9) RL=100Ω,

Figure 7

33MHz 28.0 46.2

mA

40MHz 29.0 51.7

65MHz 34.0 57.2

85MHz(10) 39.0 62.7

ICCPDT Powered-Down Supply Current /PwrDn=0.8V 10.0 55.0 μA

Notes:

7. Positive current values refer to the current flowing into device and negative values means current flowing out of

pins. Voltages are referenced to ground unless otherwise specified (except ΔVOD and VOD).

8. The power supply current for both transmitter and receiver can be different with the number of active I/O

channels.

9. The 16-grayscale test pattern tests device power consumption for a “typical” LCD display pattern. The test

pattern approximates signal switching needed to produce groups of 16 vertical strips across the display.

10. FIN1217 only.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 8

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Transmitter AC Electrical Characteristics

Typical values are at over supply voltages and operating temperatures ranges, unless otherwise specified.

Symbol Parameter Conditions Min. Typ. Max. Units

tTCP Transmit Clock Period Figure 10 11.76 T 50.00 ns

tTCH Transmit Clock (TxCLKIn) HIGH Time 0.35 0.50 0.65 T

tTCL Transmit Clock LOW Time 0.35 0.50 0.65 T

tCLKT TxCLKIn Transition Time (Rising and

Falling) 10% to 90%

Figure 11 1.0 6.0 ns

tJIT TxCLKIn Cycle-to-Cycle Jitter 3.0 ns

tXIT TxIn Transition Time 1.5 6.0 ns

LVDS Transmitter Timing Characteristics

tTLH Differential Output Rise Time (20% to 80%) Figure 8 0.75 1.50 ns

tTHL Differential Output Fall Time (80% to 20%) 0.75 1.50 ns

tSTC TxIn Setup to TxCLNIn Figure 10

f=85MHz FIN1217

only

2.5 ns

tHTC TxIn Holds to TCLKIn 0 ns

tTPDD Transmitter Power-Down Delay Figure 17(11) 100 ns

tTCCD Transmitter Clock Input to Clock Output

Delay Figure 13

TA=25°C, VCC=3.3V 2.8 5.5 6.8 ns

Transmitter Output Data Jitter (f=40 MHz)(12)

tTPPB0 Transmitter Output Pulse Position of Bit 0

Figure 20

7f 1

a×

=

-0.25 0 0.25 ns

tTPPB1 Transmitter Output Pulse Position of Bit 1 a-0.25 a a+0.25 ns

tTPPB2 Transmitter Output Pulse Position of Bit 2 2a-0.25 2a 2a+0.25 ns

tTPPB3 Transmitter Output Pulse Position of Bit 3 3a-0.25 3a 3a+0.25 ns

tTPPB4 Transmitter Output Pulse Position of Bit 4 4a-0.25 4a 4a+0.25 ns

tTPPB5 Transmitter Output Pulse Position of Bit 5 5a-0.25 5a 5a+0.25 ns

tTPPB6 Transmitter Output Pulse Position of Bit 6 6a-0.25 6a 6a+0.25 ns

Transmitter Output Data Jitter (f=65 MHz)(12)

tTPPB0 Transmitter Output Pulse Position of Bit 0

Figure 20

7f 1

a×

=

-0.2 0 0.2 ns

tTPPB1 Transmitter Output Pulse Position of Bit 1 a-0.2 a a+0.2 ns

tTPPB2 Transmitter Output Pulse Position of Bit 2 2a-0.2 2a 2a+0.2 ns

tTPPB3 Transmitter Output Pulse Position of Bit 3 3a-0.2 3a 3a+0.2 ns

tTPPB4 Transmitter Output Pulse Position of Bit 4 4a-0.2 4a 4a+0.2 ns

tTPPB5 Transmitter Output Pulse Position of Bit 5 5a-0.2 5a 5a+0.2 ns

tTPPB6 Transmitter Output Pulse Position of Bit 6 6a-0.2 6a 6a+0.2 ns

Continued on following page…

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 9

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Transmitter AC Electrical Characteristics (Continued)

Symbol Parameter Conditions Min. Typ. Max. Units

Transmitter Output Data Jitter (f=85 MHz, FIN1217 only)(12)

tTPPB0 Transmitter Output Pulse Position of Bit 0

Figure 20

7f 1

a×

=

-0.2 0 0.2 ns

tTPPB1 Transmitter Output Pulse Position of Bit 1 a-0.2 a a+0.2 ns

tTPPB2 Transmitter Output Pulse Position of Bit 2 2a-0.2 2a 2a+0.2 ns

tTPPB3 Transmitter Output Pulse Position of Bit 3 3a-0.2 3a 3a+0.2 ns

tTPPB4 Transmitter Output Pulse Position of Bit 4 4a-0.2 4a 4a+0.2 ns

tTPPB5 Transmitter Output Pulse Position of Bit 5 5a-0.2 5a 5a+0.2 ns

tTPPB6 Transmitter Output Pulse Position of Bit 6 6a-0.2 6a 6a+0.2 ns

tJCC Transmitter Clock Out Jitter, Cycle-to cycle

Figure 23

f=40MHz 350 370

ps

f=65MHz 210 230

f=85MHz

FIN1217 only 110 150

tTPLLS Transmitter Phase Lock Loop Set Time(13) Figure 15(12) 10.0 ms

Notes:

11. Outputs of all transmitters stay in 3-STATE until power reaches 2V. Clock and data output begins to toggle

10ms after VCC reaches 3V and /PwrDn pin is above 1.5V.

12. This output data pulse position works for both transmitters with 21 TTL inputs, except the LVDS output bit

mapping difference (see Figure 19). Figure 20 shows the skew between the first data bit and clock output. A

two-bit cycle delay is guaranteed when the MSB is output from transmitter.

13. This jitter specification is based on the assumption that PLL has a reference clock with cycle-to-cycle input jitter

of less than 2ns.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 10

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Receiver DC Electrical Characteristics

Typical values are at TA=25°C and with VCC=3.3V. Positive current values refer to the current flowing into device and

negative values means current flowing out of pins. Voltages are referenced to ground unless otherwise specified

(except ΔVOD and VOD). Minimum and maximum values are at over supply voltage and operating temperature ranges

unless otherwise specified.

Symbol Parameter Conditions Min. Typ. Max. Units

LVTTL/CMOS DC Characteristics

VIH Input High Voltage 2.0 VCC V

VIL Input Low Voltage GND 0.8 V

VOH Output High Voltage IOH=-0.4mA 2.7 3.3 V

VOL Output Low Voltage IOL=2mA 0.3 V

VIK Input Clamp Voltage IIK=-18mA -1.5 V

IIN Input Current VIN=0V to 4.6V -10 10 μA

IOFF Input/Output Power-Off

Leakage Current VCC=0V, All LVTTL Inputs/Outputs

0V to 4.6V ±10

μA

IOS Output Short-Circuit Current VOUT=0V -60 -120

μA

Receiver LVDS Input Characteristics

VTH Differential Input Threshold

HIGH Figure 6, Table 2 100 mV

VTL Differential Input Threshold

LOW Figure 6, Table 2 -100 mV

VICM Input Common Mode Range Figure 6, Table 2 0.05 2.35 V

IIN Input Current VIN=2.4V, VCC=3.6V or 0V ±10.0 μA

VIN=0V, VCC=3.6V or 0V ±10.0

Receiver Supply Current

ICCWR 3:21 Receiver Power Supply

Current for Worst Case

Pattern with Load(14) CL=8pF, Figure 7

33MHz 66

mA

40MHz 56 74

65MHz 75 102

85MHz(15) 92 125

ICCPDR Powered Down Supply

Current /PwrDn=0.8V (RxOut stays LOW) NA 400 μA

Notes:

14. The power supply current for the receiver can be different due to the number of active I/O channels.

15. 85MHz specification for FIN1218 only.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 11

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Receiver AC Electrical Characteristics

Values are at over supply voltages and operating temperatures, unless otherwise specified.

Symbol Parameter Conditions Min. Typ. Max. Units

tRCOL RxCLKOut LOW Time Figure 12

Rising Edge Strobe

f=40MHz

10.0 11.0 ns

tRCOH RxCLKOut HIGH Time 10.0 12.2 ns

tRSRC RxOut Valid Prior to RxCLKOut 6.5 11.6 ns

tRHRC RxOut Valid After RxCLKOut 6.0 11.6 ns

tRCOP Receiver Clock Output (RxCLKOut)

Period Figure 12

Rising Edge Strobe

f=65MHz

15.0 T 50.0 ns

tRCOL RxCLKOut LOW Time 5.0 7.8 9.0 ns

tRCOH RxCLKOut HIGH Time 5.0 7.3 9.0 ns

tRSRC RxOut Valid Prior to RxCLKOut 4.5 7.7 ns

tRHRC RxOut Valid After RxCLKOut 4.0 8.4 ns

tRCOP Receiver Clock Output (RxCLKOut)

Period Figure 12

Rising Edge Strobe

f=85MHz

FIN1218 only

11.76 T 50.00 ns

tRCOL RxCLKOut LOW Time 4.0 6.3 6.0 ns

tRCOH RxCLKOut HIGH Time 4.5 5.4 6.5 ns

tRSRC RxOut Valid Prior to RxCLKOut 3.5 6.3 ns

tRHRC RxOut Valid After RxCLKOut 3.5 6.5 ns

tROLH Output Rise Time (20% to 80%) CL=8pF, Figure 9 2.2 5.0 ns

tROHL Output Fall Time (80% to 20%) 2.1 5.0 ns

tRCCD Receiver Clock Input to Clock Output

Delay

TA=25°C, VCC=3.3V

Figure 14(Error!

Reference source not found.) 3.5 6.9 7.5 ns

tRPDD Receiver Power-Down Delay Figure 18 1.0 ms

tRSPB0 Receiver Input Strobe Position of Bit 0

Figure 21

f=40MHz

1.00 2.15 ns

tRSPB1 Receiver Input Strobe Position of Bit 1 4.5 5.8 ns

tRSPB2 Receiver Input Strobe Position of Bit 2 8.10 9.15 ns

tRSPB3 Receiver Input Strobe Position of Bit 3 11.6 12.6 ns

tRSPB4 Receiver Input Strobe Position of Bit 4 15.1 16.3 ns

tRSPB5 Receiver Input Strobe Position of Bit 5 18.8 19.9 ns

tRSPB6 Receiver Input Strobe Position of Bit 6 22.5 23.6 ns

Continued on following page…

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 12

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Receiver AC Electrical Characteristics (Continued)

Symbol Parameter Conditions Min. Typ. Max. Units

tRSPB0 Receiver Input Strobe Position of Bit 0

Figure 21

f=65MHz

0.7 1.4 ns

tRSPB1 Receiver Input Strobe Position of Bit 1 2.9 3.6 ns

tRSPB2 Receiver Input Strobe Position of Bit 2 5.1 5.8 ns

tRSPB3 Receiver Input Strobe Position of Bit 3 7.3 8.0 ns

tRSPB4 Receiver Input Strobe Position of Bit 4 9.5 10.2 ns

tRSPB5 Receiver Input Strobe Position of Bit 5 11.7 12.4 ns

tRSPB6 Receiver Input Strobe Position of Bit 6 13.9 14.6 ns

tRSPB0 Receiver Input Strobe Position of Bit 0

Figure 21

f=85MHz

FIN1218 only

0.49 1.19 ns

tRSPB1 Receiver Input Strobe Position of Bit 1 2.17 2.87 ns

tRSPB2 Receiver Input Strobe Position of Bit 2 3.85 4.55 ns

tRSPB3 Receiver Input Strobe Position of Bit 3 5.53 6.23 ns

tRSPB4 Receiver Input Strobe Position of Bit 4 7.21 7.91 ns

tRSPB5 Receiver Input Strobe Position of Bit 5 8.89 9.59 ns

tRSPB6 Receiver Input Strobe Position of Bit 6 10.57 11.27 ns

tRSKM RxIn Skew Margin(Error! Reference source not

found.)

f=40MHz, Figure 22 490 ps

f=65MHz, Figure 22 400

f=85MHz

FIN1218 only

Figure 22 252

tRPLLS Receiver Phase Lock Loop Set Time Figure 16 10.0 ms

Notes:

16. Total channel latency from serializer to deserializer is (T + tTCCD) + (2•T + tRCCD).

17. Receiver skew margin is defined as the valid sampling window after considering potential setup/hold time and

minimum/maximum bit position.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 13

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Test Circuits

Figure 5. Differential LVDS Output DC Test Circuit

Notes: For all input pulses, tR or tF<=1ns.

CL includes all probe and jig capacitance.

Figure 6. Differential Receiver Voltage Definitions, Propagation Delay, and Transition Time Test Circuit

Table 2. Receiver Minimum and Maximum Input Threshold Test Voltages

Applied Voltages (V) Resulting Differential

Input Voltage (mV) Resulting Common

Mode Input Voltage (V)

VIA V

IB V

ID V

IC

1.25 1.15 100 1.20

1.15 1.25 -100 1.20

2.40 2.30 100 2.35

2.30 2.40 -100 2.35

0.10 0 100 0.05

0 0.10 -100 0.05

1.50 0.90 600 1.20

0.90 1.50 -600 1.20

2.40 1.80 600 2.10

1.80 2.40 -600 2.10

0.60 0 600 0.30

0 0.60 -600 0.30

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 14

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

AC Loadings and Waveforms

Note: The worst-case test pattern produces a maximum toggling of digital circuits, LVDS I/O and LVTTL/CMOS I/O.

Depending on the valid strobe edge of transmitter, the TxCLKIn can be either rising or failing edge data strobe.

Figure 7. Worst-Case Test Pattern

Figure 8. Transmitter LVDS Output Load and Transition Times

Figure 9. Receiver LVTTL/CMOS Output Load and Transition Times

Figure 10. Transmitter Set-up/Hold and HIGH/LOW Times (Rising Edge Strobe)

Figure 11. Transmitter Input Clock Transition Time

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 15

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

AC Loadings and Waveforms (Continued)

Figure 12. Receiver Set-up/Hold and HIGH/LOW Times

Figure 13. Transmitter Clock-In to Clock-Out Delay (Rising Edge Strobe)

Figure 14. Receiver Clock-In to Clock-Out Delay (Rising Edge Strobe)

Figure 15. Transmitter Phase-Lock-Loop Set Time

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 16

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

AC Loadings and Waveforms (Continued)

Figure 16. Receiver Phase Lock Loop Set Time

Figure 17. Transmitter Power-down Delay

Figure 18. Receiver Power-down Delay

Note: This output date pulse position works for both transmitters with 21 TTL inputs, except the LVDS output bit

mapping difference. Two-bit cycle delay is guaranteed with the MSB is output from transmitter.

Figure 19. Parallel LVTTL Inputs Mapped to Three Serial LVDS Outputs

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 17

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

AC Loadings and Waveforms (Continued)]

Figure 20. Transmitter Output Pulse Bit Position

Figure 21. Receiver Strobe Bit Position

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 18

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

AC Loadings and Waveforms (Continued)

Note: tRSKM is the budget for the cable skew and source clock skew plus Inter-Symbol Interference (ISI).

The minimum and maximum pulse position values are based on the bit position of each of the seven bits within

the LVDS data stream across PVT (Process, Voltage Supply, and Temperature).

Figure 22. Receiver LVDS Input Skew Margin

Note: This jitter pattern is used to test the jitter response (clock out) of the device over the power supply range with

worst jitter ±ns (cycle-to-cycle) clock input. The specific test methodology is as follows:

 Switching input data TxIn0 to TxIn20 at 0.5MHz and the input clock is shifted to left -3ns and to

the right +3ns when data is HIGH (by switching between CLK1 and CLK2 in Figure 11).

 The ±3ns cycle-to-cycle input jitter is the static phase error between the two clock sources.

Jumping between two clock sources to simulate the worst-case of clock edge jump (3ns) from

graphical controllers. Cycle-to-cycle jitter at TxCLK out pin should be measured cross VCC range

with 100mV noise (VCC noise frequency <2MHz).

Figure 23. Jitter Pattern

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 19

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

Physical Dimensions

Figure 24. 48-Lead Thin Shrink Small Outline Package (TSSOP)

Pack age drawings are provided as a servic e t o customers c onsidering Fairchild components. Drawi ngs may change in any manner

without notice. P l ease note the revision and/or date on the drawing and contac t a Fairchild Semic onductor representat i ve to verify

or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically

the warranty therein, which covers Fairchild products.

Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:

http://www.fairchildsemi.com/packaging/.

FIN1215 / FIN1216 / FIN1217 • Rev. 1.0.3 20

FIN1215 / FIN1216 / FIN1217 — LVDS 21-Bit Serializers / De-Serializers

www.onsemi.com

1

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent

coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.

ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,

regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer

application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not

designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification

in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized

application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and

expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such

claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This

literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

www.onsemi.com

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative